Re: [PATCH 31/49] ath11k: add mac.c

[Vasanthakumar Thiagarajan <vthiagar-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>]

On 2019-08-21 02:16, Johannes Berg wrote:
> On Tue, 2019-08-20 at 18:47 +0300, Kalle Valo wrote:
> 
>> +static int ath11k_mac_op_config(struct ieee80211_hw *hw, u32 changed)
>> +{
>> +	struct ath11k *ar = hw->priv;
>> +	int ret = 0;
>> +
>> +	/* mac80211 requires this op to be present and that's why
>> +	 * there's an empty function, this can be extended when
>> +	 * required.
>> +	 */
> 
> Well, oops. Maybe it shouldn't be required?

I think we require this for some configuration handling. The comment is 
to be updated with
proper information. We'll address that.

> 
>> +	mutex_lock(&ar->conf_mutex);
>> +
>> +	/* TODO: Handle configuration changes as appropriate */
>> +
>> +	mutex_unlock(&ar->conf_mutex);
> 
> It's not actually empty though - why bother locking the mutex for
> nothing?

Sure, we'll remove this locking.

> 
>> +	if (sta->mfp) {
>> +		/* TODO: Need to check if FW supports PMF? */
> 
> Probably not? shouldn't get a sta with MFP unless you advertised 
> support
> for it. At least I'd think so, and consider it a mac80211 bug if you
> still did.
> 

I could see driver getting sta with MFP irrespective of whether driver
advertises it's support in hw_flags by setting IEEE80211_HW_MFP_CAPABLE.
I see MFP station in driver even when I remove the support for the MFP 
cipher
suits in STA mode. I agree all these needs to be handled in mac80211.

>> +	/* This is a workaround for HT-enabled STAs which break the spec
>> +	 * and have no HT capabilities RX mask (no HT RX MCS map).
>> +	 *
>> +	 * As per spec, in section 20.3.5 Modulation and coding scheme 
>> (MCS),
>> +	 * MCS 0 through 7 are mandatory in 20MHz with 800 ns GI at all 
>> STAs.
> 
> Wouldn't that better be in mac80211?

Right.

> 
>> +	ampdu_factor = (vht_cap->cap &
>> +			IEEE80211_VHT_CAP_MAX_A_MPDU_LENGTH_EXPONENT_MASK) >>
>> +		       IEEE80211_VHT_CAP_MAX_A_MPDU_LENGTH_EXPONENT_SHIFT;
> 
> consider u32_get_bits() or something like that from bitfield.h
> 
>> +	/* Workaround: Some Netgear/Linksys 11ac APs set Rx A-MPDU factor to
>> +	 * zero in VHT IE. Using it would result in degraded throughput.
>> +	 * arg->peer_max_mpdu at this point contains HT max_mpdu so keep
>> +	 * it if VHT max_mpdu is smaller.
>> +	 */
>> +	arg->peer_max_mpdu = max(arg->peer_max_mpdu,
>> +				 (1U << (IEEE80211_HT_MAX_AMPDU_FACTOR +
>> +					ampdu_factor)) - 1);
> 
> Wait, that seems familiar. Again, put it into mac80211?
> 

Sure.

>> +static void ath11k_peer_assoc_h_smps(struct ieee80211_sta *sta,
>> +				     struct peer_assoc_params *arg)
>> +{
>> +	const struct ieee80211_sta_ht_cap *ht_cap = &sta->ht_cap;
>> +	int smps;
>> +
>> +	if (!ht_cap->ht_supported)
>> +		return;
>> +
>> +	smps = ht_cap->cap & IEEE80211_HT_CAP_SM_PS;
>> +	smps >>= IEEE80211_HT_CAP_SM_PS_SHIFT;
> 
> also here, u*_get_bits() or something might be nicer
> 
> (and yes, I've written tons of code like this myself before that
> existed, which is why I'm pointing it out - it's much nicer)
> 

Ok.

>> +void ath11k_mac_drain_tx(struct ath11k *ar)
>> +{
>> +	/* make sure rcu-protected mac80211 tx path itself is drained */
>> +	synchronize_net();
> 
> Doesn't mac80211 ensure that in the relevant places like flush()? But
> then again, not sure where you call this.

This tx drain cleans up any pending management frames in the software 
queue.
This will be done from hw_restart and drv_start callback to make sure we
do not have any pending management frames.

> 
>> +	ath11k_dbg(ar->ab, ATH11K_DBG_MAC, "mac set fixed rate params vdev 
>> %i rate 0x%02hhx nss %hhu sgi %hhu\n",
>> +		   arvif->vdev_id, rate, nss, sgi);
> 
> nit: that could use a line-break
> 
>> +	vdev_param = WMI_VDEV_PARAM_FIXED_RATE;
>> +	ret = ath11k_wmi_vdev_set_param_cmd(ar, arvif->vdev_id,
>> +					    vdev_param, rate);
>> +	if (ret) {
>> +		ath11k_warn(ar->ab, "failed to set fixed rate param 0x%02x: %d\n",
>> 
>> +	/* TODO: Check if HT capability advertised from firmware is 
>> different
>> +	 * for each band for a dual band capable radio. It will be tricky to
>> +	 * handle it when the ht capability different for each band.
>> +	 */
> 
> For each band shouldn't really be that tricky?
> 

Sure, we'll review and address this TODO.

Thanks,
Vasanth

> _______________________________________________
> ath11k mailing list
> ath11k-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
> http://lists.infradead.org/mailman/listinfo/ath11k