From: Konrad Dybcio <konrad.dybcio@linaro.org>
To: Lux Aliaga <they@mint.lgbt>,
agross@kernel.org, andersson@kernel.org, robh+dt@kernel.org,
krzysztof.kozlowski+dt@linaro.org, vkoul@kernel.org,
kishon@kernel.org, alim.akhtar@samsung.com, avri.altman@wdc.com,
bvanassche@acm.org, keescook@chromium.org, tony.luck@intel.com,
gpiccoli@igalia.com
Cc: ~postmarketos/upstreaming@lists.sr.ht,
linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, linux-phy@lists.infradead.org,
linux-scsi@vger.kernel.org, linux-hardening@vger.kernel.org,
phone-devel@vger.kernel.org, martin.botka@somainline.org,
marijn.suijten@somainline.org
Subject: Re: [PATCH v6 6/6] arm64: dts: qcom: sm6125: Initial support for xiaomi-laurel-sprout
Date: Mon, 9 Jan 2023 13:21:01 +0100 [thread overview]
Message-ID: <ee8c5ad1-77c0-43fe-a233-ee1fa31f1a3a@linaro.org> (raw)
In-Reply-To: <20230108195336.388349-7-they@mint.lgbt>
On 8.01.2023 20:53, Lux Aliaga wrote:
> Add support for the Xiaomi Mi A3 (xiaomi-laurel-sprout). Here's a
> summary on what's defined.
>
> - dmesg output to bootloader preconfigured display
> - USB
> - UFS
> - SD card
> - SMD RPM regulators
> - Volume Up, Down and Power buttons
> - Thermistors
>
> Signed-off-by: Lux Aliaga <they@mint.lgbt>
> ---
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> .../dts/qcom/sm6125-xiaomi-laurel-sprout.dts | 424 ++++++++++++++++++
> 2 files changed, 425 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/sm6125-xiaomi-laurel-sprout.dts
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 3e79496292e7..2b2a0170db14 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -157,6 +157,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sdm850-lenovo-yoga-c630.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm850-samsung-w737.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sm4250-oneplus-billie2.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sm6125-sony-xperia-seine-pdx201.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += sm6125-xiaomi-laurel-sprout.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sm6350-sony-xperia-lena-pdx213.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sm6375-sony-xperia-murray-pdx225.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sm7225-fairphone-fp4.dtb
> diff --git a/arch/arm64/boot/dts/qcom/sm6125-xiaomi-laurel-sprout.dts b/arch/arm64/boot/dts/qcom/sm6125-xiaomi-laurel-sprout.dts
> new file mode 100644
> index 000000000000..7ff18f481060
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sm6125-xiaomi-laurel-sprout.dts
> @@ -0,0 +1,424 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2022, Lux Aliaga <they@mint.lgbt>
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/input/gpio-keys.h>
> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
> +#include "sm6125.dtsi"
> +#include "pm6125.dtsi"
> +
> +/ {
> + model = "Xiaomi Mi A3";
> + compatible = "xiaomi,laurel-sprout", "qcom,sm6125";
> + chassis-type = "handset";
> +
> + /* required for bootloader to select correct board */
> + qcom,msm-id = <394 0>; /* sm6125 v1 */
> + qcom,board-id = <11 0>;
> +
> + chosen {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + framebuffer0: framebuffer@5c000000 {
> + compatible = "simple-framebuffer";
> + reg = <0 0x5c000000 0 (1560 * 720 * 4)>;
> + width = <720>;
> + height = <1560>;
> + stride = <(720 * 4)>;
> + format = "a8r8g8b8";
> + };
> + };
> +
> + reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
These two properties are already set in the SoC dtsi, you can
drop them.
> +
> + debug_mem: debug@ffb00000 {
> + reg = <0x0 0xffb00000 0x0 0xc0000>;
> + no-map;
> + };
> +
> + last_log_mem: lastlog@ffbc0000 {
> + reg = <0x0 0xffbc0000 0x0 0x80000>;
> + no-map;
> + };
> +
> + pstore_mem: ramoops@ffc00000 {
> + compatible = "ramoops";
> + reg = <0x0 0xffc40000 0x0 0xc0000>;
> + record-size = <0x1000>;
> + console-size = <0x40000>;
> + msg-size = <0x20000 0x20000>;
> + };
> +
> + cmdline_mem: memory@ffd00000 {
> + reg = <0x0 0xffd40000 0x0 0x1000>;
> + no-map;
> + };
> + };
> +
> + extcon_usb: usb-id {
> + compatible = "linux,extcon-usb-gpio";
> + id-gpio = <&tlmm 102 GPIO_ACTIVE_HIGH>;
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> +
> + pinctrl-0 = <&vol_up_n>;
> + pinctrl-names = "default";
> +
> + key-volume-up {
> + label = "Volume Up";
> + gpios = <&pm6125_gpio 5 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_VOLUMEUP>;
> + debounce-interval = <15>;
> + linux,can-disable;
> + wakeup-source;
> + };
> + };
> +
> + thermal-zones {
> + rf-pa0-thermal {
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
> + thermal-sensors = <&pm6125_adc_tm 0>;
> +
> + trips {
> + active-config0 {
> + temperature = <125000>;
> + hysteresis = <1000>;
> + type = "critical";
> + };
> + };
> + };
> +
> + quiet-thermal {
> + polling-delay-passive = <0>;
> + polling-delay = <5000>;
> + thermal-sensors = <&pm6125_adc_tm 1>;
> +
> + trips {
> + active-config0 {
> + temperature = <125000>;
> + hysteresis = <1000>;
> + type = "critical";
> + };
> + };
> + };
> +
> + xo-thermal {
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
> + thermal-sensors = <&pm6125_adc_tm 2>;
> +
> + trips {
> + active-config0 {
> + temperature = <125000>;
> + hysteresis = <1000>;
> + type = "critical";
> + };
> + };
> + };
> + };
> +};
> +
> +&hsusb_phy1 {
> + vdd-supply = <&vreg_l7a>;
> + vdda-pll-supply = <&vreg_l10a>;
> + vdda-phy-dpdm-supply = <&vreg_l15a>;
> + status = "okay";
> +};
> +
> +&pm6125_adc {
> + pinctrl-names = "default";
> + pinctrl-0 = <&camera_flash_therm &emmc_ufs_therm>;
> +
> + adc-chan@4d {
> + reg = <ADC5_AMUX_THM1_100K_PU>;
> + qcom,ratiometric;
> + qcom,hw-settle-time = <200>;
> + qcom,pre-scaling = <1 1>;
> + label = "rf_pa0_therm";
> + };
> +
> + adc-chan@4e {
> + reg = <ADC5_AMUX_THM2_100K_PU>;
> + qcom,ratiometric;
> + qcom,hw-settle-time = <200>;
> + qcom,pre-scaling = <1 1>;
> + label = "quiet_therm";
> + };
> +
> + adc-chan@52 {
> + reg = <ADC5_GPIO1_100K_PU>;
> + qcom,ratiometric;
> + qcom,hw-settle-time = <200>;
> + qcom,pre-scaling = <1 1>;
> + label = "camera_flash_therm";
> + };
> +
> + adc-chan@54 {
> + reg = <ADC5_GPIO3_100K_PU>;
> + qcom,ratiometric;
> + qcom,hw-settle-time = <200>;
> + qcom,pre-scaling = <1 1>;
> + label = "emmc_ufs_therm";
> + };
> +};
> +
> +&pm6125_adc_tm {
> + status = "okay";
> +
> + rf-pa0-therm@0 {
> + reg = <0>;
> + io-channels = <&pm6125_adc ADC5_AMUX_THM1_100K_PU>;
> + qcom,ratiometric;
> + qcom,hw-settle-time-us = <200>;
> + };
> +
> + quiet-therm@1 {
> + reg = <1>;
> + io-channels = <&pm6125_adc ADC5_AMUX_THM2_100K_PU>;
> + qcom,ratiometric;
> + qcom,hw-settle-time-us = <200>;
> + };
> +
> + xo-therm@2 {
> + reg = <2>;
> + io-channels = <&pm6125_adc ADC5_XO_THERM_100K_PU>;
> + qcom,ratiometric;
> + qcom,hw-settle-time-us = <200>;
> + };
> +};
> +
> +&pm6125_gpio {
> + camera_flash_therm: camera-flash-therm-state {
> + pins = "gpio3";
> + function = PMIC_GPIO_FUNC_NORMAL;
> + bias-high-impedance;
> + };
> +
> + emmc_ufs_therm: emmc-ufs-therm-state {
> + pins = "gpio6";
> + function = PMIC_GPIO_FUNC_NORMAL;
> + bias-high-impedance;
> + };
> +
> + vol_up_n: vol-up-n-state {
> + pins = "gpio5";
> + function = PMIC_GPIO_FUNC_NORMAL;
> + input-enable;
> + bias-pull-up;
> + };
> +};
> +
> +&pon_pwrkey {
> + status = "okay";
> +};
> +
> +&pon_resin {
> + status = "okay";
> + linux,code = <KEY_VOLUMEDOWN>;
Status should go last.
With these two addressed:
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Konrad
> +};
> +
> +&rpm_requests {
> + regulators-0 {
> + compatible = "qcom,rpm-pm6125-regulators";
> +
> + vreg_s6a: s6 {
> + regulator-min-microvolt = <936000>;
> + regulator-max-microvolt = <1422000>;
> + };
> +
> + vreg_l1a: l1 {
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1256000>;
> + };
> +
> + vreg_l2a: l2 {
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1056000>;
> + };
> +
> + vreg_l3a: l3 {
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1064000>;
> + };
> +
> + vreg_l4a: l4 {
> + regulator-min-microvolt = <872000>;
> + regulator-max-microvolt = <976000>;
> + regulator-allow-set-load;
> + };
> +
> + vreg_l5a: l5 {
> + regulator-min-microvolt = <1648000>;
> + regulator-max-microvolt = <2950000>;
> + regulator-allow-set-load;
> + };
> +
> + vreg_l6a: l6 {
> + regulator-min-microvolt = <576000>;
> + regulator-max-microvolt = <656000>;
> + };
> +
> + vreg_l7a: l7 {
> + regulator-min-microvolt = <872000>;
> + regulator-max-microvolt = <976000>;
> + };
> +
> + vreg_l8a: l8 {
> + regulator-min-microvolt = <400000>;
> + regulator-max-microvolt = <728000>;
> + };
> +
> + vreg_l9a: l9 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1896000>;
> + };
> +
> + vreg_l10a: l10 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1896000>;
> + regulator-allow-set-load;
> + };
> +
> + vreg_l11a: l11 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1952000>;
> + regulator-allow-set-load;
> + };
> +
> + vreg_l12a: l12 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1996000>;
> + };
> +
> + vreg_l13a: l13 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1832000>;
> + };
> +
> + vreg_l14a: l14 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1904000>;
> + };
> +
> + vreg_l15a: l15 {
> + regulator-min-microvolt = <3104000>;
> + regulator-max-microvolt = <3232000>;
> + };
> +
> + vreg_l16a: l16 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1904000>;
> + };
> +
> + vreg_l17a: l17 {
> + regulator-min-microvolt = <1248000>;
> + regulator-max-microvolt = <1304000>;
> + };
> +
> + vreg_l18a: l18 {
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1264000>;
> + regulator-allow-set-load;
> + };
> +
> + vreg_l19a: l19 {
> + regulator-min-microvolt = <1648000>;
> + regulator-max-microvolt = <2952000>;
> + };
> +
> + vreg_l20a: l20 {
> + regulator-min-microvolt = <1648000>;
> + regulator-max-microvolt = <2952000>;
> + };
> +
> + vreg_l21a: l21 {
> + regulator-min-microvolt = <2600000>;
> + regulator-max-microvolt = <2856000>;
> + };
> +
> + vreg_l22a: l22 {
> + regulator-min-microvolt = <2944000>;
> + regulator-max-microvolt = <2950000>;
> + regulator-allow-set-load;
> + };
> +
> + vreg_l23a: l23 {
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3400000>;
> + };
> +
> + vreg_l24a: l24 {
> + regulator-min-microvolt = <2944000>;
> + regulator-max-microvolt = <2950000>;
> + regulator-allow-set-load;
> + };
> + };
> +};
> +
> +&sdc2_off_state {
> + sd-cd-pins {
> + pins = "gpio98";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +};
> +
> +&sdc2_on_state {
> + sd-cd-pins {
> + pins = "gpio98";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +};
> +
> +&sdhc_2 {
> + cd-gpios = <&tlmm 98 GPIO_ACTIVE_HIGH>;
> + vmmc-supply = <&vreg_l22a>;
> + vqmmc-supply = <&vreg_l5a>;
> + no-sdio;
> + no-mmc;
> + status = "okay";
> +};
> +
> +&tlmm {
> + gpio-reserved-ranges = <22 2>, <28 6>;
> +};
> +
> +&ufs_mem_hc {
> + vcc-supply = <&vreg_l24a>;
> + vccq2-supply = <&vreg_l11a>;
> + vcc-max-microamp = <600000>;
> + vccq2-max-microamp = <600000>;
> + status = "okay";
> +};
> +
> +&ufs_mem_phy {
> + vdda-phy-supply = <&vreg_l4a>;
> + vdda-pll-supply = <&vreg_l10a>;
> + vdda-phy-max-microamp = <51400>;
> + vdda-pll-max-microamp = <14200>;
> + vddp-ref-clk-supply = <&vreg_l18a>;
> + status = "okay";
> +};
> +
> +&usb3 {
> + status = "okay";
> +};
> +
> +&usb3_dwc3 {
> + extcon = <&extcon_usb>;
> +};
next prev parent reply other threads:[~2023-01-09 12:21 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-01-08 19:53 [PATCH v6 0/6] arm64: dts: qcom: sm6125: UFS and xiaomi-laurel-sprout support Lux Aliaga
2023-01-08 19:53 ` [PATCH v6 1/6] dt-bindings: ufs: qcom: Add SM6125 compatible string Lux Aliaga
2023-01-08 19:53 ` [PATCH v6 2/6] dt-bindings: phy: Add QMP UFS PHY compatible for SM6125 Lux Aliaga
2023-01-09 12:19 ` Krzysztof Kozlowski
2023-01-13 18:21 ` Vinod Koul
2023-01-08 19:53 ` [PATCH v6 3/6] phy: qcom-qmp: Add SM6125 UFS PHY support Lux Aliaga
2023-01-13 18:21 ` Vinod Koul
2023-01-13 19:31 ` Dmitry Baryshkov
2023-02-09 14:34 ` Lux Aliaga
2023-01-08 19:53 ` [PATCH v6 4/6] arm64: dts: qcom: sm6125: Add UFS nodes Lux Aliaga
2023-01-09 12:18 ` Konrad Dybcio
2023-01-11 2:53 ` Lux Aliaga
2023-01-11 12:04 ` Konrad Dybcio
2023-01-17 20:01 ` Caleb Connolly
2023-01-08 19:53 ` [PATCH v6 5/6] dt-bindings: arm: qcom: Document xiaomi,laurel-sprout board Lux Aliaga
2023-01-08 19:53 ` [PATCH v6 6/6] arm64: dts: qcom: sm6125: Initial support for xiaomi-laurel-sprout Lux Aliaga
2023-01-09 12:21 ` Konrad Dybcio [this message]
2023-01-10 11:56 ` Marijn Suijten
2023-01-10 12:03 ` [PATCH v6 0/6] arm64: dts: qcom: sm6125: UFS and xiaomi-laurel-sprout support Marijn Suijten
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=ee8c5ad1-77c0-43fe-a233-ee1fa31f1a3a@linaro.org \
--to=konrad.dybcio@linaro.org \
--cc=agross@kernel.org \
--cc=alim.akhtar@samsung.com \
--cc=andersson@kernel.org \
--cc=avri.altman@wdc.com \
--cc=bvanassche@acm.org \
--cc=devicetree@vger.kernel.org \
--cc=gpiccoli@igalia.com \
--cc=keescook@chromium.org \
--cc=kishon@kernel.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-hardening@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-phy@lists.infradead.org \
--cc=linux-scsi@vger.kernel.org \
--cc=marijn.suijten@somainline.org \
--cc=martin.botka@somainline.org \
--cc=phone-devel@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=they@mint.lgbt \
--cc=tony.luck@intel.com \
--cc=vkoul@kernel.org \
--cc=~postmarketos/upstreaming@lists.sr.ht \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).