[PATCH v5 00/16] PCI: imx6: Clean up and add imx95 pci support

[PATCH v5 00/16] PCI: imx6: Clean up and add imx95 pci support

[Frank Li]

first 6 patches use drvdata: flags to simplify some switch-case code.
Improve maintaince and easy to read code.

Then add imx95 basic pci host function.

follow two patch do endpoint code clean up.
Then add imx95 basic endpont function.

Compared with v2, added EP function support and some fixes,  please change
notes at each patches.

dt-binding pass pcie node:

pcie0: pcie@4c300000 {
                        compatible = "fsl,imx95-pcie";
                        reg = <0 0x4c300000 0 0x40000>,
                                <0 0x4c360000 0 0x10000>,
                                <0 0x4c340000 0 0x20000>,
                                <0 0x60100000 0 0xfe00000>;
                        reg-names = "dbi", "atu", "app", "config";
                        #address-cells = <3>;
                        #size-cells = <2>;
                        device_type = "pci";
                        linux,pci-domain = <0>;
                        bus-range = <0x00 0xff>;
                        ranges = <0x81000000 0x0 0x00000000 0x0 0x6ff00000 0 0x00100000>,
                                 <0x82000000 0x0 0x10000000 0x9 0x10000000 0 0x10000000>;
                        num-lanes = <1>;
                        num-viewport = <8>;
                        interrupts = <GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH>;
                        interrupt-names = "msi";
                        #interrupt-cells = <1>;
                        interrupt-map-mask = <0 0 0 0x7>;
                        interrupt-map = <0 0 0 1 &gic 0 0 GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH>,
                                        <0 0 0 2 &gic 0 0 GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH>,
                                        <0 0 0 3 &gic 0 0 GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>,
                                        <0 0 0 4 &gic 0 0 GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>;
                        fsl,max-link-speed = <3>;
                        clocks = <&scmi_clk IMX95_CLK_HSIO>,
                                 <&scmi_clk IMX95_CLK_HSIOPLL>,
                                 <&scmi_clk IMX95_CLK_HSIOPLL_VCO>,
                                 <&scmi_clk IMX95_CLK_HSIOPCIEAUX>;
                        clock-names = "pcie", "pcie_bus", "pcie_phy", "pcie_aux";
                        assigned-clocks =<&scmi_clk IMX95_CLK_HSIOPLL_VCO>,
                                         <&scmi_clk IMX95_CLK_HSIOPLL>,
                                         <&scmi_clk IMX95_CLK_HSIOPCIEAUX>;
                        assigned-clock-rates = <3600000000>, <100000000>, <10000000>;
                        assigned-clock-parents = <0>, <0>,
                                                 <&scmi_clk IMX95_CLK_SYSPLL1_PFD1_DIV2>;
                        power-domains = <&scmi_devpd IMX95_PD_HSIO_TOP>;
                        /* 0x30~0x37 stream id for pci0 */
                        /*
                         * iommu-map = <0x000 &apps_smmu 0x30 0x1>,
                         * <0x100 &apps_smmu 0x31 0x1>;
                         */
                        status = "disabled";
                };

pcie1: pcie-ep@4c380000 {
                        compatible = "fsl,imx95-pcie-ep";
                        reg = <0 0x4c380000 0 0x20000>,
                              <0 0x4c3e0000 0 0x1000>,
                              <0 0x4c3a0000 0 0x1000>,
                              <0 0x4c3c0000 0 0x10000>,
                              <0 0x4c3f0000 0 0x10000>,
                              <0xa 0 1 0>;
                        reg-names = "dbi", "atu", "dbi2", "app", "dma", "addr_space";
                        interrupts = <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>;
                        interrupt-names = "dma";
                        fsl,max-link-speed = <3>;
                        clocks = <&scmi_clk IMX95_CLK_HSIO>,
                                 <&scmi_clk IMX95_CLK_HSIOPLL>,
                                 <&scmi_clk IMX95_CLK_HSIOPLL_VCO>,
                                 <&scmi_clk IMX95_CLK_HSIOPCIEAUX>;
                        clock-names = "pcie", "pcie_bus", "pcie_phy", "pcie_aux";
                        assigned-clocks =<&scmi_clk IMX95_CLK_HSIOPLL_VCO>,
                                         <&scmi_clk IMX95_CLK_HSIOPLL>,
                                         <&scmi_clk IMX95_CLK_HSIOPCIEAUX>;
                        assigned-clock-rates = <3600000000>, <100000000>, <10000000>;
                        assigned-clock-parents = <0>, <0>,
                                                 <&scmi_clk IMX95_CLK_SYSPLL1_PFD1_DIV2>;
                        power-domains = <&scmi_devpd IMX95_PD_HSIO_TOP>;
                        status = "disabled";
                };

Frank Li (15):
  PCI: imx6: Simplify clock handling by using bulk_clk_*() function
  PCI: imx6: Simplify phy handling by using by using
    IMX6_PCIE_FLAG_HAS_PHY
  PCI: imx6: Simplify reset handling by using by using
    *_FLAG_HAS_*_RESET
  dt-bindings: imx6q-pcie: Add linux,pci-domain as required for iMX8MQ
  PCI: imx6: Using "linux,pci-domain" as slot ID
  PCI: imx6: Simplify ltssm_enable() by using ltssm_off and ltssm_mask
  PCI: imx6: Simplify configure_type() by using mode_off and mode_mask
  PCI: imx6: Simplify switch-case logic by involve init_phy callback
  dt-bindings: imx6q-pcie: Clean up irrationality clocks check
  dt-bindings: imx6q-pcie: remove reg and reg-name
  PCI: imx6: Add iMX95 PCIe support
  PCI: imx6: Clean up get addr_space code
  PCI: imx6: Add epc_features in imx6_pcie_drvdata
  dt-bindings: imx6q-pcie: Add iMX95 pcie endpoint compatible string
  PCI: imx6: Add iMX95 Endpoint (EP) function support

Richard Zhu (1):
  dt-bindings: imx6q-pcie: Add imx95 pcie compatible string

 .../bindings/pci/fsl,imx6q-pcie-common.yaml   |  28 +-
 .../bindings/pci/fsl,imx6q-pcie-ep.yaml       |  52 +-
 .../bindings/pci/fsl,imx6q-pcie.yaml          |  28 +-
 drivers/pci/controller/dwc/pci-imx6.c         | 628 ++++++++++--------
 4 files changed, 426 insertions(+), 310 deletions(-)

-- 
2.34.1

[PATCH v5 01/16] PCI: imx6: Simplify clock handling by using bulk_clk_*() function

[Frank Li]

Refactors the clock handling logic. Adds clk_names[] define in drvdata.
Using clk_bulk*() api simplifies the code.

Signed-off-by: Frank Li <Frank.Li@nxp.com>
---

Notes:
    Change from v4 to v5
    - update commit message
    - direct using clk name list, instead of macro
    - still keep caculate clk list count because sizeof return pre allocated
    array size.
    
    Change from v3 to v4
    - using clk_bulk_*() API
    Change from v1 to v3
    - none

 drivers/pci/controller/dwc/pci-imx6.c | 125 ++++++++------------------
 1 file changed, 35 insertions(+), 90 deletions(-)

diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c
index 74703362aeec7..50d9faaa17f71 100644
--- a/drivers/pci/controller/dwc/pci-imx6.c
+++ b/drivers/pci/controller/dwc/pci-imx6.c
@@ -61,12 +61,15 @@ enum imx6_pcie_variants {
 #define IMX6_PCIE_FLAG_IMX6_SPEED_CHANGE	BIT(1)
 #define IMX6_PCIE_FLAG_SUPPORTS_SUSPEND		BIT(2)
 
+#define IMX6_PCIE_MAX_CLKS       6
+
 struct imx6_pcie_drvdata {
 	enum imx6_pcie_variants variant;
 	enum dw_pcie_device_mode mode;
 	u32 flags;
 	int dbi_length;
 	const char *gpr;
+	const char *clk_names[IMX6_PCIE_MAX_CLKS];
 };
 
 struct imx6_pcie {
@@ -74,11 +77,8 @@ struct imx6_pcie {
 	int			reset_gpio;
 	bool			gpio_active_high;
 	bool			link_is_up;
-	struct clk		*pcie_bus;
-	struct clk		*pcie_phy;
-	struct clk		*pcie_inbound_axi;
-	struct clk		*pcie;
-	struct clk		*pcie_aux;
+	struct clk_bulk_data	clks[IMX6_PCIE_MAX_CLKS];
+	u32			clks_cnt;
 	struct regmap		*iomuxc_gpr;
 	u16			msi_ctrl;
 	u32			controller_id;
@@ -407,13 +407,18 @@ static void imx7d_pcie_wait_for_phy_pll_lock(struct imx6_pcie *imx6_pcie)
 
 static int imx6_setup_phy_mpll(struct imx6_pcie *imx6_pcie)
 {
-	unsigned long phy_rate = clk_get_rate(imx6_pcie->pcie_phy);
+	unsigned long phy_rate = 0;
 	int mult, div;
 	u16 val;
+	int i;
 
 	if (!(imx6_pcie->drvdata->flags & IMX6_PCIE_FLAG_IMX6_PHY))
 		return 0;
 
+	for (i = 0; i < imx6_pcie->clks_cnt; i++)
+		if (strncmp(imx6_pcie->clks[i].id, "pcie_phy", 8) == 0)
+			phy_rate = clk_get_rate(imx6_pcie->clks[i].clk);
+
 	switch (phy_rate) {
 	case 125000000:
 		/*
@@ -550,19 +555,11 @@ static int imx6_pcie_attach_pd(struct device *dev)
 
 static int imx6_pcie_enable_ref_clk(struct imx6_pcie *imx6_pcie)
 {
-	struct dw_pcie *pci = imx6_pcie->pci;
-	struct device *dev = pci->dev;
 	unsigned int offset;
 	int ret = 0;
 
 	switch (imx6_pcie->drvdata->variant) {
 	case IMX6SX:
-		ret = clk_prepare_enable(imx6_pcie->pcie_inbound_axi);
-		if (ret) {
-			dev_err(dev, "unable to enable pcie_axi clock\n");
-			break;
-		}
-
 		regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
 				   IMX6SX_GPR12_PCIE_TEST_POWERDOWN, 0);
 		break;
@@ -589,12 +586,6 @@ static int imx6_pcie_enable_ref_clk(struct imx6_pcie *imx6_pcie)
 	case IMX8MQ_EP:
 	case IMX8MP:
 	case IMX8MP_EP:
-		ret = clk_prepare_enable(imx6_pcie->pcie_aux);
-		if (ret) {
-			dev_err(dev, "unable to enable pcie_aux clock\n");
-			break;
-		}
-
 		offset = imx6_pcie_grp_offset(imx6_pcie);
 		/*
 		 * Set the over ride low and enabled
@@ -615,9 +606,6 @@ static int imx6_pcie_enable_ref_clk(struct imx6_pcie *imx6_pcie)
 static void imx6_pcie_disable_ref_clk(struct imx6_pcie *imx6_pcie)
 {
 	switch (imx6_pcie->drvdata->variant) {
-	case IMX6SX:
-		clk_disable_unprepare(imx6_pcie->pcie_inbound_axi);
-		break;
 	case IMX6QP:
 	case IMX6Q:
 		regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1,
@@ -631,14 +619,6 @@ static void imx6_pcie_disable_ref_clk(struct imx6_pcie *imx6_pcie)
 				   IMX7D_GPR12_PCIE_PHY_REFCLK_SEL,
 				   IMX7D_GPR12_PCIE_PHY_REFCLK_SEL);
 		break;
-	case IMX8MM:
-	case IMX8MM_EP:
-	case IMX8MQ:
-	case IMX8MQ_EP:
-	case IMX8MP:
-	case IMX8MP_EP:
-		clk_disable_unprepare(imx6_pcie->pcie_aux);
-		break;
 	default:
 		break;
 	}
@@ -650,23 +630,9 @@ static int imx6_pcie_clk_enable(struct imx6_pcie *imx6_pcie)
 	struct device *dev = pci->dev;
 	int ret;
 
-	ret = clk_prepare_enable(imx6_pcie->pcie_phy);
-	if (ret) {
-		dev_err(dev, "unable to enable pcie_phy clock\n");
+	ret =  clk_bulk_prepare_enable(imx6_pcie->clks_cnt, imx6_pcie->clks);
+	if (ret)
 		return ret;
-	}
-
-	ret = clk_prepare_enable(imx6_pcie->pcie_bus);
-	if (ret) {
-		dev_err(dev, "unable to enable pcie_bus clock\n");
-		goto err_pcie_bus;
-	}
-
-	ret = clk_prepare_enable(imx6_pcie->pcie);
-	if (ret) {
-		dev_err(dev, "unable to enable pcie clock\n");
-		goto err_pcie;
-	}
 
 	ret = imx6_pcie_enable_ref_clk(imx6_pcie);
 	if (ret) {
@@ -679,11 +645,7 @@ static int imx6_pcie_clk_enable(struct imx6_pcie *imx6_pcie)
 	return 0;
 
 err_ref_clk:
-	clk_disable_unprepare(imx6_pcie->pcie);
-err_pcie:
-	clk_disable_unprepare(imx6_pcie->pcie_bus);
-err_pcie_bus:
-	clk_disable_unprepare(imx6_pcie->pcie_phy);
+	clk_bulk_disable_unprepare(imx6_pcie->clks_cnt, imx6_pcie->clks);
 
 	return ret;
 }
@@ -691,9 +653,7 @@ static int imx6_pcie_clk_enable(struct imx6_pcie *imx6_pcie)
 static void imx6_pcie_clk_disable(struct imx6_pcie *imx6_pcie)
 {
 	imx6_pcie_disable_ref_clk(imx6_pcie);
-	clk_disable_unprepare(imx6_pcie->pcie);
-	clk_disable_unprepare(imx6_pcie->pcie_bus);
-	clk_disable_unprepare(imx6_pcie->pcie_phy);
+	clk_bulk_disable_unprepare(imx6_pcie->clks_cnt, imx6_pcie->clks);
 }
 
 static void imx6_pcie_assert_core_reset(struct imx6_pcie *imx6_pcie)
@@ -1305,32 +1265,19 @@ static int imx6_pcie_probe(struct platform_device *pdev)
 		return imx6_pcie->reset_gpio;
 	}
 
-	/* Fetch clocks */
-	imx6_pcie->pcie_bus = devm_clk_get(dev, "pcie_bus");
-	if (IS_ERR(imx6_pcie->pcie_bus))
-		return dev_err_probe(dev, PTR_ERR(imx6_pcie->pcie_bus),
-				     "pcie_bus clock source missing or invalid\n");
+	while (imx6_pcie->drvdata->clk_names[imx6_pcie->clks_cnt]) {
+		int i = imx6_pcie->clks_cnt;
+
+		imx6_pcie->clks[i].id = imx6_pcie->drvdata->clk_names[i];
+		imx6_pcie->clks_cnt++;
+	}
 
-	imx6_pcie->pcie = devm_clk_get(dev, "pcie");
-	if (IS_ERR(imx6_pcie->pcie))
-		return dev_err_probe(dev, PTR_ERR(imx6_pcie->pcie),
-				     "pcie clock source missing or invalid\n");
+	/* Fetch clocks */
+	ret = devm_clk_bulk_get(dev, imx6_pcie->clks_cnt, imx6_pcie->clks);
+	if (ret)
+		return ret;
 
 	switch (imx6_pcie->drvdata->variant) {
-	case IMX6SX:
-		imx6_pcie->pcie_inbound_axi = devm_clk_get(dev,
-							   "pcie_inbound_axi");
-		if (IS_ERR(imx6_pcie->pcie_inbound_axi))
-			return dev_err_probe(dev, PTR_ERR(imx6_pcie->pcie_inbound_axi),
-					     "pcie_inbound_axi clock missing or invalid\n");
-		break;
-	case IMX8MQ:
-	case IMX8MQ_EP:
-		imx6_pcie->pcie_aux = devm_clk_get(dev, "pcie_aux");
-		if (IS_ERR(imx6_pcie->pcie_aux))
-			return dev_err_probe(dev, PTR_ERR(imx6_pcie->pcie_aux),
-					     "pcie_aux clock source missing or invalid\n");
-		fallthrough;
 	case IMX7D:
 		if (dbi_base->start == IMX8MQ_PCIE2_BASE_ADDR)
 			imx6_pcie->controller_id = 1;
@@ -1353,10 +1300,6 @@ static int imx6_pcie_probe(struct platform_device *pdev)
 	case IMX8MM_EP:
 	case IMX8MP:
 	case IMX8MP_EP:
-		imx6_pcie->pcie_aux = devm_clk_get(dev, "pcie_aux");
-		if (IS_ERR(imx6_pcie->pcie_aux))
-			return dev_err_probe(dev, PTR_ERR(imx6_pcie->pcie_aux),
-					     "pcie_aux clock source missing or invalid\n");
 		imx6_pcie->apps_reset = devm_reset_control_get_exclusive(dev,
 									 "apps");
 		if (IS_ERR(imx6_pcie->apps_reset))
@@ -1372,14 +1315,6 @@ static int imx6_pcie_probe(struct platform_device *pdev)
 	default:
 		break;
 	}
-	/* Don't fetch the pcie_phy clock, if it has abstract PHY driver */
-	if (imx6_pcie->phy == NULL) {
-		imx6_pcie->pcie_phy = devm_clk_get(dev, "pcie_phy");
-		if (IS_ERR(imx6_pcie->pcie_phy))
-			return dev_err_probe(dev, PTR_ERR(imx6_pcie->pcie_phy),
-					     "pcie_phy clock source missing or invalid\n");
-	}
-
 
 	/* Grab turnoff reset */
 	imx6_pcie->turnoff_reset = devm_reset_control_get_optional_exclusive(dev, "turnoff");
@@ -1477,6 +1412,7 @@ static const struct imx6_pcie_drvdata drvdata[] = {
 			 IMX6_PCIE_FLAG_IMX6_SPEED_CHANGE,
 		.dbi_length = 0x200,
 		.gpr = "fsl,imx6q-iomuxc-gpr",
+		.clk_names = {"pcie_bus", "pcie", "pcie_phy"},
 	},
 	[IMX6SX] = {
 		.variant = IMX6SX,
@@ -1484,6 +1420,7 @@ static const struct imx6_pcie_drvdata drvdata[] = {
 			 IMX6_PCIE_FLAG_IMX6_SPEED_CHANGE |
 			 IMX6_PCIE_FLAG_SUPPORTS_SUSPEND,
 		.gpr = "fsl,imx6q-iomuxc-gpr",
+		.clk_names = {"pcie_bus", "pcie", "pcie_phy", "pcie_inbound_axi"},
 	},
 	[IMX6QP] = {
 		.variant = IMX6QP,
@@ -1492,40 +1429,48 @@ static const struct imx6_pcie_drvdata drvdata[] = {
 			 IMX6_PCIE_FLAG_SUPPORTS_SUSPEND,
 		.dbi_length = 0x200,
 		.gpr = "fsl,imx6q-iomuxc-gpr",
+		.clk_names = {"pcie_bus", "pcie", "pcie_phy"},
 	},
 	[IMX7D] = {
 		.variant = IMX7D,
 		.flags = IMX6_PCIE_FLAG_SUPPORTS_SUSPEND,
 		.gpr = "fsl,imx7d-iomuxc-gpr",
+		.clk_names = {"pcie_bus", "pcie", "pcie_phy"},
 	},
 	[IMX8MQ] = {
 		.variant = IMX8MQ,
 		.gpr = "fsl,imx8mq-iomuxc-gpr",
+		.clk_names = {"pcie_bus", "pcie", "pcie_phy", "pcie_aux"},
 	},
 	[IMX8MM] = {
 		.variant = IMX8MM,
 		.flags = IMX6_PCIE_FLAG_SUPPORTS_SUSPEND,
 		.gpr = "fsl,imx8mm-iomuxc-gpr",
+		.clk_names = {"pcie_bus", "pcie", "pcie_aux"},
 	},
 	[IMX8MP] = {
 		.variant = IMX8MP,
 		.flags = IMX6_PCIE_FLAG_SUPPORTS_SUSPEND,
 		.gpr = "fsl,imx8mp-iomuxc-gpr",
+		.clk_names = {"pcie_bus", "pcie", "pcie_aux"},
 	},
 	[IMX8MQ_EP] = {
 		.variant = IMX8MQ_EP,
 		.mode = DW_PCIE_EP_TYPE,
 		.gpr = "fsl,imx8mq-iomuxc-gpr",
+		.clk_names = {"pcie_bus", "pcie", "pcie_phy", "pcie_aux"},
 	},
 	[IMX8MM_EP] = {
 		.variant = IMX8MM_EP,
 		.mode = DW_PCIE_EP_TYPE,
 		.gpr = "fsl,imx8mm-iomuxc-gpr",
+		.clk_names = {"pcie_bus", "pcie", "pcie_aux"},
 	},
 	[IMX8MP_EP] = {
 		.variant = IMX8MP_EP,
 		.mode = DW_PCIE_EP_TYPE,
 		.gpr = "fsl,imx8mp-iomuxc-gpr",
+		.clk_names = {"pcie_bus", "pcie", "pcie_aux"},
 	},
 };
 
-- 
2.34.1

[PATCH v5 02/16] PCI: imx6: Simplify phy handling by using by using IMX6_PCIE_FLAG_HAS_PHY

[Frank Li]

Refactors the phy handling logic in the imx6 PCI driver by adding
IMX6_PCIE_FLAG_HAS_PHY bitmask define for drvdata::flags.

The drvdata::flags and a bitmask ensures a cleaner and more scalable
switch-case structure for handling phy.

Signed-off-by: Frank Li <Frank.Li@nxp.com>
---

Notes:
    Change from v4 to v5:
    - none, Keep IMX6_PCIE_FLAG_HAS_PHY to indicate dts mismatch when platform
    require phy suppport.
    
    Change from v1 to v3:
    - none

 drivers/pci/controller/dwc/pci-imx6.c | 23 ++++++++++++++++-------
 1 file changed, 16 insertions(+), 7 deletions(-)

diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c
index 50d9faaa17f71..4d620249f3d52 100644
--- a/drivers/pci/controller/dwc/pci-imx6.c
+++ b/drivers/pci/controller/dwc/pci-imx6.c
@@ -60,6 +60,9 @@ enum imx6_pcie_variants {
 #define IMX6_PCIE_FLAG_IMX6_PHY			BIT(0)
 #define IMX6_PCIE_FLAG_IMX6_SPEED_CHANGE	BIT(1)
 #define IMX6_PCIE_FLAG_SUPPORTS_SUSPEND		BIT(2)
+#define IMX6_PCIE_FLAG_HAS_PHY			BIT(3)
+
+#define imx6_check_flag(pci, val)     (pci->drvdata->flags & val)
 
 #define IMX6_PCIE_MAX_CLKS       6
 
@@ -1277,6 +1280,13 @@ static int imx6_pcie_probe(struct platform_device *pdev)
 	if (ret)
 		return ret;
 
+	if (imx6_check_flag(imx6_pcie, IMX6_PCIE_FLAG_HAS_PHY)) {
+		imx6_pcie->phy = devm_phy_get(dev, "pcie-phy");
+		if (IS_ERR(imx6_pcie->phy))
+			return dev_err_probe(dev, PTR_ERR(imx6_pcie->phy),
+					     "failed to get pcie phy\n");
+	}
+
 	switch (imx6_pcie->drvdata->variant) {
 	case IMX7D:
 		if (dbi_base->start == IMX8MQ_PCIE2_BASE_ADDR)
@@ -1306,11 +1316,6 @@ static int imx6_pcie_probe(struct platform_device *pdev)
 			return dev_err_probe(dev, PTR_ERR(imx6_pcie->apps_reset),
 					     "failed to get pcie apps reset control\n");
 
-		imx6_pcie->phy = devm_phy_get(dev, "pcie-phy");
-		if (IS_ERR(imx6_pcie->phy))
-			return dev_err_probe(dev, PTR_ERR(imx6_pcie->phy),
-					     "failed to get pcie phy\n");
-
 		break;
 	default:
 		break;
@@ -1444,13 +1449,15 @@ static const struct imx6_pcie_drvdata drvdata[] = {
 	},
 	[IMX8MM] = {
 		.variant = IMX8MM,
-		.flags = IMX6_PCIE_FLAG_SUPPORTS_SUSPEND,
+		.flags = IMX6_PCIE_FLAG_SUPPORTS_SUSPEND |
+			 IMX6_PCIE_FLAG_HAS_PHY,
 		.gpr = "fsl,imx8mm-iomuxc-gpr",
 		.clk_names = {"pcie_bus", "pcie", "pcie_aux"},
 	},
 	[IMX8MP] = {
 		.variant = IMX8MP,
-		.flags = IMX6_PCIE_FLAG_SUPPORTS_SUSPEND,
+		.flags = IMX6_PCIE_FLAG_SUPPORTS_SUSPEND |
+			 IMX6_PCIE_FLAG_HAS_PHY,
 		.gpr = "fsl,imx8mp-iomuxc-gpr",
 		.clk_names = {"pcie_bus", "pcie", "pcie_aux"},
 	},
@@ -1462,12 +1469,14 @@ static const struct imx6_pcie_drvdata drvdata[] = {
 	},
 	[IMX8MM_EP] = {
 		.variant = IMX8MM_EP,
+		.flags = IMX6_PCIE_FLAG_HAS_PHY,
 		.mode = DW_PCIE_EP_TYPE,
 		.gpr = "fsl,imx8mm-iomuxc-gpr",
 		.clk_names = {"pcie_bus", "pcie", "pcie_aux"},
 	},
 	[IMX8MP_EP] = {
 		.variant = IMX8MP_EP,
+		.flags = IMX6_PCIE_FLAG_HAS_PHY,
 		.mode = DW_PCIE_EP_TYPE,
 		.gpr = "fsl,imx8mp-iomuxc-gpr",
 		.clk_names = {"pcie_bus", "pcie", "pcie_aux"},
-- 
2.34.1

[PATCH v5 03/16] PCI: imx6: Simplify reset handling by using by using *_FLAG_HAS_*_RESET

[Frank Li]

Refactors the reset handling logic in the imx6 PCI driver by adding
IMX6_PCIE_FLAG_HAS_*_RESET bitmask define for drvdata::flags.

The drvdata::flags and a bitmask ensures a cleaner and more scalable
switch-case structure for handling reset.

Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---

Notes:
    Change from v4 to v5:
    - Add Mani's Reviewed-by tag
    - Fixed MQ_EP's flags
    
    Chagne from v3 to v4:
    - none
    Change from v2 to v3:
    - add Philipp's Reviewed-by tag
    Change from v1 to v2:
    - remove condition check before reset_control_(de)assert() because it is
      none ops if a NULL pointer pass down.
    - still keep condition check at probe to help identify dts file mismatch
      problem.
    
    Change from v1 to v2:
    - remove condition check before reset_control_(de)assert() because it is
      none ops if a NULL pointer pass down.
    - still keep condition check at probe to help identify dts file mismatch
      problem.

 drivers/pci/controller/dwc/pci-imx6.c | 108 ++++++++++----------------
 1 file changed, 41 insertions(+), 67 deletions(-)

diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c
index 4d620249f3d52..294f61a9c6fd9 100644
--- a/drivers/pci/controller/dwc/pci-imx6.c
+++ b/drivers/pci/controller/dwc/pci-imx6.c
@@ -61,6 +61,8 @@ enum imx6_pcie_variants {
 #define IMX6_PCIE_FLAG_IMX6_SPEED_CHANGE	BIT(1)
 #define IMX6_PCIE_FLAG_SUPPORTS_SUSPEND		BIT(2)
 #define IMX6_PCIE_FLAG_HAS_PHY			BIT(3)
+#define IMX6_PCIE_FLAG_HAS_APP_RESET		BIT(4)
+#define IMX6_PCIE_FLAG_HAS_PHY_RESET		BIT(5)
 
 #define imx6_check_flag(pci, val)     (pci->drvdata->flags & val)
 
@@ -661,18 +663,10 @@ static void imx6_pcie_clk_disable(struct imx6_pcie *imx6_pcie)
 
 static void imx6_pcie_assert_core_reset(struct imx6_pcie *imx6_pcie)
 {
+	reset_control_assert(imx6_pcie->pciephy_reset);
+	reset_control_assert(imx6_pcie->apps_reset);
+
 	switch (imx6_pcie->drvdata->variant) {
-	case IMX7D:
-	case IMX8MQ:
-	case IMX8MQ_EP:
-		reset_control_assert(imx6_pcie->pciephy_reset);
-		fallthrough;
-	case IMX8MM:
-	case IMX8MM_EP:
-	case IMX8MP:
-	case IMX8MP_EP:
-		reset_control_assert(imx6_pcie->apps_reset);
-		break;
 	case IMX6SX:
 		regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
 				   IMX6SX_GPR12_PCIE_TEST_POWERDOWN,
@@ -693,6 +687,8 @@ static void imx6_pcie_assert_core_reset(struct imx6_pcie *imx6_pcie)
 		regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1,
 				   IMX6Q_GPR1_PCIE_REF_CLK_EN, 0 << 16);
 		break;
+	default:
+		break;
 	}
 
 	/* Some boards don't have PCIe reset GPIO. */
@@ -706,14 +702,10 @@ static int imx6_pcie_deassert_core_reset(struct imx6_pcie *imx6_pcie)
 	struct dw_pcie *pci = imx6_pcie->pci;
 	struct device *dev = pci->dev;
 
+	reset_control_deassert(imx6_pcie->pciephy_reset);
+
 	switch (imx6_pcie->drvdata->variant) {
-	case IMX8MQ:
-	case IMX8MQ_EP:
-		reset_control_deassert(imx6_pcie->pciephy_reset);
-		break;
 	case IMX7D:
-		reset_control_deassert(imx6_pcie->pciephy_reset);
-
 		/* Workaround for ERR010728, failure of PCI-e PLL VCO to
 		 * oscillate, especially when cold.  This turns off "Duty-cycle
 		 * Corrector" and other mysterious undocumented things.
@@ -745,11 +737,7 @@ static int imx6_pcie_deassert_core_reset(struct imx6_pcie *imx6_pcie)
 
 		usleep_range(200, 500);
 		break;
-	case IMX6Q:		/* Nothing to do */
-	case IMX8MM:
-	case IMX8MM_EP:
-	case IMX8MP:
-	case IMX8MP_EP:
+	default:
 		break;
 	}
 
@@ -796,16 +784,11 @@ static void imx6_pcie_ltssm_enable(struct device *dev)
 				   IMX6Q_GPR12_PCIE_CTL_2,
 				   IMX6Q_GPR12_PCIE_CTL_2);
 		break;
-	case IMX7D:
-	case IMX8MQ:
-	case IMX8MQ_EP:
-	case IMX8MM:
-	case IMX8MM_EP:
-	case IMX8MP:
-	case IMX8MP_EP:
-		reset_control_deassert(imx6_pcie->apps_reset);
+	default:
 		break;
 	}
+
+	reset_control_deassert(imx6_pcie->apps_reset);
 }
 
 static void imx6_pcie_ltssm_disable(struct device *dev)
@@ -819,16 +802,11 @@ static void imx6_pcie_ltssm_disable(struct device *dev)
 		regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
 				   IMX6Q_GPR12_PCIE_CTL_2, 0);
 		break;
-	case IMX7D:
-	case IMX8MQ:
-	case IMX8MQ_EP:
-	case IMX8MM:
-	case IMX8MM_EP:
-	case IMX8MP:
-	case IMX8MP_EP:
-		reset_control_assert(imx6_pcie->apps_reset);
+	default:
 		break;
 	}
+
+	reset_control_assert(imx6_pcie->apps_reset);
 }
 
 static int imx6_pcie_start_link(struct dw_pcie *pci)
@@ -1287,36 +1265,24 @@ static int imx6_pcie_probe(struct platform_device *pdev)
 					     "failed to get pcie phy\n");
 	}
 
-	switch (imx6_pcie->drvdata->variant) {
-	case IMX7D:
-		if (dbi_base->start == IMX8MQ_PCIE2_BASE_ADDR)
-			imx6_pcie->controller_id = 1;
-
-		imx6_pcie->pciephy_reset = devm_reset_control_get_exclusive(dev,
-									    "pciephy");
-		if (IS_ERR(imx6_pcie->pciephy_reset)) {
-			dev_err(dev, "Failed to get PCIEPHY reset control\n");
-			return PTR_ERR(imx6_pcie->pciephy_reset);
-		}
-
-		imx6_pcie->apps_reset = devm_reset_control_get_exclusive(dev,
-									 "apps");
-		if (IS_ERR(imx6_pcie->apps_reset)) {
-			dev_err(dev, "Failed to get PCIE APPS reset control\n");
-			return PTR_ERR(imx6_pcie->apps_reset);
-		}
-		break;
-	case IMX8MM:
-	case IMX8MM_EP:
-	case IMX8MP:
-	case IMX8MP_EP:
-		imx6_pcie->apps_reset = devm_reset_control_get_exclusive(dev,
-									 "apps");
+	if (imx6_check_flag(imx6_pcie, IMX6_PCIE_FLAG_HAS_APP_RESET)) {
+		imx6_pcie->apps_reset = devm_reset_control_get_exclusive(dev, "apps");
 		if (IS_ERR(imx6_pcie->apps_reset))
 			return dev_err_probe(dev, PTR_ERR(imx6_pcie->apps_reset),
 					     "failed to get pcie apps reset control\n");
+	}
 
-		break;
+	if (imx6_check_flag(imx6_pcie, IMX6_PCIE_FLAG_HAS_PHY_RESET)) {
+		imx6_pcie->pciephy_reset = devm_reset_control_get_exclusive(dev, "pciephy");
+		if (IS_ERR(imx6_pcie->pciephy_reset))
+			return dev_err_probe(dev, PTR_ERR(imx6_pcie->pciephy_reset),
+					     "Failed to get PCIEPHY reset control\n");
+	}
+
+	switch (imx6_pcie->drvdata->variant) {
+	case IMX7D:
+		if (dbi_base->start == IMX8MQ_PCIE2_BASE_ADDR)
+			imx6_pcie->controller_id = 1;
 	default:
 		break;
 	}
@@ -1438,31 +1404,39 @@ static const struct imx6_pcie_drvdata drvdata[] = {
 	},
 	[IMX7D] = {
 		.variant = IMX7D,
-		.flags = IMX6_PCIE_FLAG_SUPPORTS_SUSPEND,
+		.flags = IMX6_PCIE_FLAG_SUPPORTS_SUSPEND |
+			 IMX6_PCIE_FLAG_HAS_APP_RESET |
+			 IMX6_PCIE_FLAG_HAS_PHY_RESET,
 		.gpr = "fsl,imx7d-iomuxc-gpr",
 		.clk_names = {"pcie_bus", "pcie", "pcie_phy"},
 	},
 	[IMX8MQ] = {
 		.variant = IMX8MQ,
+		.flags = IMX6_PCIE_FLAG_HAS_APP_RESET |
+			 IMX6_PCIE_FLAG_HAS_PHY_RESET,
 		.gpr = "fsl,imx8mq-iomuxc-gpr",
 		.clk_names = {"pcie_bus", "pcie", "pcie_phy", "pcie_aux"},
 	},
 	[IMX8MM] = {
 		.variant = IMX8MM,
 		.flags = IMX6_PCIE_FLAG_SUPPORTS_SUSPEND |
-			 IMX6_PCIE_FLAG_HAS_PHY,
+			 IMX6_PCIE_FLAG_HAS_PHY |
+			 IMX6_PCIE_FLAG_HAS_APP_RESET,
 		.gpr = "fsl,imx8mm-iomuxc-gpr",
 		.clk_names = {"pcie_bus", "pcie", "pcie_aux"},
 	},
 	[IMX8MP] = {
 		.variant = IMX8MP,
 		.flags = IMX6_PCIE_FLAG_SUPPORTS_SUSPEND |
-			 IMX6_PCIE_FLAG_HAS_PHY,
+			 IMX6_PCIE_FLAG_HAS_PHY |
+			 IMX6_PCIE_FLAG_HAS_APP_RESET,
 		.gpr = "fsl,imx8mp-iomuxc-gpr",
 		.clk_names = {"pcie_bus", "pcie", "pcie_aux"},
 	},
 	[IMX8MQ_EP] = {
 		.variant = IMX8MQ_EP,
+		.flags = IMX6_PCIE_FLAG_HAS_APP_RESET |
+			 IMX6_PCIE_FLAG_HAS_PHY_RESET,
 		.mode = DW_PCIE_EP_TYPE,
 		.gpr = "fsl,imx8mq-iomuxc-gpr",
 		.clk_names = {"pcie_bus", "pcie", "pcie_phy", "pcie_aux"},
-- 
2.34.1

[PATCH v5 04/16] dt-bindings: imx6q-pcie: Add linux,pci-domain as required for iMX8MQ

[Frank Li]

iMX8MQ have two pci controllers. Adds "linux,pci-domain" as required
proptery for iMX8MQ to indicate pci controller index.

Signed-off-by: Frank Li <Frank.Li@nxp.com>
---

Notes:
    Change from v4 to v5
    - new patch at v5

 .../bindings/pci/fsl,imx6q-pcie-common.yaml           | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie-common.yaml b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie-common.yaml
index d91b639ae7ae7..8f39b4e6e8491 100644
--- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie-common.yaml
+++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie-common.yaml
@@ -265,6 +265,17 @@ allOf:
             - const: apps
             - const: turnoff
 
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - fsl,imx8mq-pcie
+              - fsl,imx8mq-pcie-ep
+    then:
+      required:
+        - linux,pci-domain
+
 additionalProperties: true
 
 ...
-- 
2.34.1

Re: [PATCH v5 04/16] dt-bindings: imx6q-pcie: Add linux,pci-domain as required for iMX8MQ

[Krzysztof Kozlowski]

On 20/12/2023 22:36, Frank Li wrote:
> iMX8MQ have two pci controllers. Adds "linux,pci-domain" as required
> proptery for iMX8MQ to indicate pci controller index.


Why it has to be required? Everything will work fine if skipped.
Otherwise please provide reason why it must be *required*.

Best regards,
Krzysztof

Re: [PATCH v5 04/16] dt-bindings: imx6q-pcie: Add linux,pci-domain as required for iMX8MQ

[Frank Li]

On Sat, Dec 23, 2023 at 07:40:28PM +0100, Krzysztof Kozlowski wrote:
> On 20/12/2023 22:36, Frank Li wrote:
> > iMX8MQ have two pci controllers. Adds "linux,pci-domain" as required
> > proptery for iMX8MQ to indicate pci controller index.
> 
> 
> Why it has to be required? Everything will work fine if skipped.
> Otherwise please provide reason why it must be *required*.

Next patch will use "linux,pci-domain" as PCI slot ID, instead compared
with hard code register address.

The below code will be removed.

-		if (dbi_base->start == IMX8MQ_PCIE2_BASE_ADDR)
-			imx6_pcie->controller_id = 1;


when there are more than 2 controller, this compare logic will become
complex. 

So after next patch, "linux,pci-domain" will be required.

Frank

> 
> Best regards,
> Krzysztof
> 

Re: [PATCH v5 04/16] dt-bindings: imx6q-pcie: Add linux,pci-domain as required for iMX8MQ

[Krzysztof Kozlowski]

On 24/12/2023 05:29, Frank Li wrote:
> On Sat, Dec 23, 2023 at 07:40:28PM +0100, Krzysztof Kozlowski wrote:
>> On 20/12/2023 22:36, Frank Li wrote:
>>> iMX8MQ have two pci controllers. Adds "linux,pci-domain" as required
>>> proptery for iMX8MQ to indicate pci controller index.
>>
>>
>> Why it has to be required? Everything will work fine if skipped.
>> Otherwise please provide reason why it must be *required*.
> 
> Next patch will use "linux,pci-domain" as PCI slot ID, instead compared
> with hard code register address.
> 
> The below code will be removed.
> 
> -		if (dbi_base->start == IMX8MQ_PCIE2_BASE_ADDR)
> -			imx6_pcie->controller_id = 1;
> 
> 
> when there are more than 2 controller, this compare logic will become
> complex. 
> 
> So after next patch, "linux,pci-domain" will be required.

Nothing in commit msg explains this. Why you cannot use some
auto-incremented values when this is missing?

Best regards,
Krzysztof

[PATCH v5 05/16] PCI: imx6: Using "linux,pci-domain" as slot ID

[Frank Li]

Avoid use get slot id by compared with register physical address. If there
are more than 2 slots, compared logic will become complex.

"linux,pci-domain" already exist at dts since commit:
	commit (c0b70f05c87f3b arm64: dts: imx8mq: use_dt_domains for pci node).

So it is safe to remove compare basic address code:
	...
	if (dbi_base->start == IMX8MQ_PCIE2_BASE_ADDR)
		imx6_pcie->controller_id = 1;
	...

Signed-off-by: Frank Li <Frank.Li@nxp.com>
---

Notes:
    Change from v3 to v4
    - remove compare basic address logic
    Change from v2 to v3
    - none
    Change from v1 to v2
    - fix of_get_pci_domain_nr return value check logic

 drivers/pci/controller/dwc/pci-imx6.c | 17 +++++++++--------
 1 file changed, 9 insertions(+), 8 deletions(-)

diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c
index 294f61a9c6fd9..332c392f8e5bc 100644
--- a/drivers/pci/controller/dwc/pci-imx6.c
+++ b/drivers/pci/controller/dwc/pci-imx6.c
@@ -33,6 +33,7 @@
 #include <linux/pm_domain.h>
 #include <linux/pm_runtime.h>
 
+#include "../../pci.h"
 #include "pcie-designware.h"
 
 #define IMX8MQ_GPR_PCIE_REF_USE_PAD		BIT(9)
@@ -40,7 +41,6 @@
 #define IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE	BIT(11)
 #define IMX8MQ_GPR_PCIE_VREG_BYPASS		BIT(12)
 #define IMX8MQ_GPR12_PCIE2_CTRL_DEVICE_TYPE	GENMASK(11, 8)
-#define IMX8MQ_PCIE2_BASE_ADDR			0x33c00000
 
 #define to_imx6_pcie(x)	dev_get_drvdata((x)->dev)
 
@@ -1279,13 +1279,14 @@ static int imx6_pcie_probe(struct platform_device *pdev)
 					     "Failed to get PCIEPHY reset control\n");
 	}
 
-	switch (imx6_pcie->drvdata->variant) {
-	case IMX7D:
-		if (dbi_base->start == IMX8MQ_PCIE2_BASE_ADDR)
-			imx6_pcie->controller_id = 1;
-	default:
-		break;
-	}
+	/* Using linux,pci-domain as PCI slot id */
+	imx6_pcie->controller_id = of_get_pci_domain_nr(node);
+	/* If there are not "linux,pci-domain" in dts file, means only 1 controller */
+	if (imx6_pcie->controller_id == -EINVAL)
+		imx6_pcie->controller_id = 0;
+	else if (imx6_pcie->controller_id < 0)
+		return dev_err_probe(dev, imx6_pcie->controller_id,
+				     "linux,pci-domain have wrong value\n");
 
 	/* Grab turnoff reset */
 	imx6_pcie->turnoff_reset = devm_reset_control_get_optional_exclusive(dev, "turnoff");
-- 
2.34.1

[PATCH v5 06/16] PCI: imx6: Simplify ltssm_enable() by using ltssm_off and ltssm_mask

[Frank Li]

Add drvdata::ltssm_off and drvdata::ltssm_mask to simple
imx6_pcie_ltssm_enable(disable)() logic.

Signed-off-by: Frank Li <Frank.Li@nxp.com>
---

Notes:
    Change from v1 to v3
    - none

 drivers/pci/controller/dwc/pci-imx6.c | 37 ++++++++++++---------------
 1 file changed, 16 insertions(+), 21 deletions(-)

diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c
index 332c392f8e5bc..588bfb616260e 100644
--- a/drivers/pci/controller/dwc/pci-imx6.c
+++ b/drivers/pci/controller/dwc/pci-imx6.c
@@ -75,6 +75,8 @@ struct imx6_pcie_drvdata {
 	int dbi_length;
 	const char *gpr;
 	const char *clk_names[IMX6_PCIE_MAX_CLKS];
+	const u32 ltssm_off;
+	const u32 ltssm_mask;
 };
 
 struct imx6_pcie {
@@ -775,18 +777,11 @@ static int imx6_pcie_wait_for_speed_change(struct imx6_pcie *imx6_pcie)
 static void imx6_pcie_ltssm_enable(struct device *dev)
 {
 	struct imx6_pcie *imx6_pcie = dev_get_drvdata(dev);
+	const struct imx6_pcie_drvdata *drvdata = imx6_pcie->drvdata;
 
-	switch (imx6_pcie->drvdata->variant) {
-	case IMX6Q:
-	case IMX6SX:
-	case IMX6QP:
-		regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
-				   IMX6Q_GPR12_PCIE_CTL_2,
-				   IMX6Q_GPR12_PCIE_CTL_2);
-		break;
-	default:
-		break;
-	}
+	if (drvdata->ltssm_mask)
+		regmap_update_bits(imx6_pcie->iomuxc_gpr, drvdata->ltssm_off, drvdata->ltssm_mask,
+				   drvdata->ltssm_mask);
 
 	reset_control_deassert(imx6_pcie->apps_reset);
 }
@@ -794,17 +789,11 @@ static void imx6_pcie_ltssm_enable(struct device *dev)
 static void imx6_pcie_ltssm_disable(struct device *dev)
 {
 	struct imx6_pcie *imx6_pcie = dev_get_drvdata(dev);
+	const struct imx6_pcie_drvdata *drvdata = imx6_pcie->drvdata;
 
-	switch (imx6_pcie->drvdata->variant) {
-	case IMX6Q:
-	case IMX6SX:
-	case IMX6QP:
-		regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
-				   IMX6Q_GPR12_PCIE_CTL_2, 0);
-		break;
-	default:
-		break;
-	}
+	if (drvdata->ltssm_mask)
+		regmap_update_bits(imx6_pcie->iomuxc_gpr, drvdata->ltssm_off,
+				   drvdata->ltssm_mask, 0);
 
 	reset_control_assert(imx6_pcie->apps_reset);
 }
@@ -1385,6 +1374,8 @@ static const struct imx6_pcie_drvdata drvdata[] = {
 		.dbi_length = 0x200,
 		.gpr = "fsl,imx6q-iomuxc-gpr",
 		.clk_names = {"pcie_bus", "pcie", "pcie_phy"},
+		.ltssm_off = IOMUXC_GPR12,
+		.ltssm_mask = IMX6Q_GPR12_PCIE_CTL_2,
 	},
 	[IMX6SX] = {
 		.variant = IMX6SX,
@@ -1393,6 +1384,8 @@ static const struct imx6_pcie_drvdata drvdata[] = {
 			 IMX6_PCIE_FLAG_SUPPORTS_SUSPEND,
 		.gpr = "fsl,imx6q-iomuxc-gpr",
 		.clk_names = {"pcie_bus", "pcie", "pcie_phy", "pcie_inbound_axi"},
+		.ltssm_off = IOMUXC_GPR12,
+		.ltssm_mask = IMX6Q_GPR12_PCIE_CTL_2,
 	},
 	[IMX6QP] = {
 		.variant = IMX6QP,
@@ -1402,6 +1395,8 @@ static const struct imx6_pcie_drvdata drvdata[] = {
 		.dbi_length = 0x200,
 		.gpr = "fsl,imx6q-iomuxc-gpr",
 		.clk_names = {"pcie_bus", "pcie", "pcie_phy"},
+		.ltssm_off = IOMUXC_GPR12,
+		.ltssm_mask = IMX6Q_GPR12_PCIE_CTL_2,
 	},
 	[IMX7D] = {
 		.variant = IMX7D,
-- 
2.34.1

[PATCH v5 07/16] PCI: imx6: Simplify configure_type() by using mode_off and mode_mask

[Frank Li]

Add drvdata::mode_off and drvdata::mode_mask to simple
imx6_pcie_configure_type() logic.

Signed-off-by: Frank Li <Frank.Li@nxp.com>
---

Notes:
    Change from v2 to v3
    - none
    Change from v1 to v2
    - use ffs() to fixe build error.

 drivers/pci/controller/dwc/pci-imx6.c | 60 ++++++++++++++++++---------
 1 file changed, 40 insertions(+), 20 deletions(-)

diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c
index 588bfb616260e..717e8fa030deb 100644
--- a/drivers/pci/controller/dwc/pci-imx6.c
+++ b/drivers/pci/controller/dwc/pci-imx6.c
@@ -68,6 +68,7 @@ enum imx6_pcie_variants {
 
 #define IMX6_PCIE_MAX_CLKS       6
 
+#define IMX6_PCIE_MAX_INSTANCES			2
 struct imx6_pcie_drvdata {
 	enum imx6_pcie_variants variant;
 	enum dw_pcie_device_mode mode;
@@ -77,6 +78,8 @@ struct imx6_pcie_drvdata {
 	const char *clk_names[IMX6_PCIE_MAX_CLKS];
 	const u32 ltssm_off;
 	const u32 ltssm_mask;
+	const u32 mode_off[IMX6_PCIE_MAX_INSTANCES];
+	const u32 mode_mask[IMX6_PCIE_MAX_INSTANCES];
 };
 
 struct imx6_pcie {
@@ -174,32 +177,25 @@ static unsigned int imx6_pcie_grp_offset(const struct imx6_pcie *imx6_pcie)
 
 static void imx6_pcie_configure_type(struct imx6_pcie *imx6_pcie)
 {
-	unsigned int mask, val, mode;
+	const struct imx6_pcie_drvdata *drvdata = imx6_pcie->drvdata;
+	unsigned int mask, val, mode, id;
 
-	if (imx6_pcie->drvdata->mode == DW_PCIE_EP_TYPE)
+	if (drvdata->mode == DW_PCIE_EP_TYPE)
 		mode = PCI_EXP_TYPE_ENDPOINT;
 	else
 		mode = PCI_EXP_TYPE_ROOT_PORT;
 
-	switch (imx6_pcie->drvdata->variant) {
-	case IMX8MQ:
-	case IMX8MQ_EP:
-		if (imx6_pcie->controller_id == 1) {
-			mask = IMX8MQ_GPR12_PCIE2_CTRL_DEVICE_TYPE;
-			val  = FIELD_PREP(IMX8MQ_GPR12_PCIE2_CTRL_DEVICE_TYPE,
-					  mode);
-		} else {
-			mask = IMX6Q_GPR12_DEVICE_TYPE;
-			val  = FIELD_PREP(IMX6Q_GPR12_DEVICE_TYPE, mode);
-		}
-		break;
-	default:
-		mask = IMX6Q_GPR12_DEVICE_TYPE;
-		val  = FIELD_PREP(IMX6Q_GPR12_DEVICE_TYPE, mode);
-		break;
-	}
+	id = imx6_pcie->controller_id;
+
+	/* If mode_mask[id] is zero, means each controller have its individual gpr */
+	if (!drvdata->mode_mask[id])
+		id = 0;
+
+	mask = drvdata->mode_mask[id];
+	/* FIELD_PREP mask have been constant */
+	val = mode << (ffs(mask) - 1);
 
-	regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12, mask, val);
+	regmap_update_bits(imx6_pcie->iomuxc_gpr, drvdata->mode_off[id], mask, val);
 }
 
 static int pcie_phy_poll_ack(struct imx6_pcie *imx6_pcie, bool exp_val)
@@ -1376,6 +1372,8 @@ static const struct imx6_pcie_drvdata drvdata[] = {
 		.clk_names = {"pcie_bus", "pcie", "pcie_phy"},
 		.ltssm_off = IOMUXC_GPR12,
 		.ltssm_mask = IMX6Q_GPR12_PCIE_CTL_2,
+		.mode_off[0] = IOMUXC_GPR12,
+		.mode_mask[0] = IMX6Q_GPR12_DEVICE_TYPE,
 	},
 	[IMX6SX] = {
 		.variant = IMX6SX,
@@ -1386,6 +1384,8 @@ static const struct imx6_pcie_drvdata drvdata[] = {
 		.clk_names = {"pcie_bus", "pcie", "pcie_phy", "pcie_inbound_axi"},
 		.ltssm_off = IOMUXC_GPR12,
 		.ltssm_mask = IMX6Q_GPR12_PCIE_CTL_2,
+		.mode_off[0] = IOMUXC_GPR12,
+		.mode_mask[0] = IMX6Q_GPR12_DEVICE_TYPE,
 	},
 	[IMX6QP] = {
 		.variant = IMX6QP,
@@ -1397,6 +1397,8 @@ static const struct imx6_pcie_drvdata drvdata[] = {
 		.clk_names = {"pcie_bus", "pcie", "pcie_phy"},
 		.ltssm_off = IOMUXC_GPR12,
 		.ltssm_mask = IMX6Q_GPR12_PCIE_CTL_2,
+		.mode_off[0] = IOMUXC_GPR12,
+		.mode_mask[0] = IMX6Q_GPR12_DEVICE_TYPE,
 	},
 	[IMX7D] = {
 		.variant = IMX7D,
@@ -1405,6 +1407,8 @@ static const struct imx6_pcie_drvdata drvdata[] = {
 			 IMX6_PCIE_FLAG_HAS_PHY_RESET,
 		.gpr = "fsl,imx7d-iomuxc-gpr",
 		.clk_names = {"pcie_bus", "pcie", "pcie_phy"},
+		.mode_off[0] = IOMUXC_GPR12,
+		.mode_mask[0] = IMX6Q_GPR12_DEVICE_TYPE,
 	},
 	[IMX8MQ] = {
 		.variant = IMX8MQ,
@@ -1412,6 +1416,10 @@ static const struct imx6_pcie_drvdata drvdata[] = {
 			 IMX6_PCIE_FLAG_HAS_PHY_RESET,
 		.gpr = "fsl,imx8mq-iomuxc-gpr",
 		.clk_names = {"pcie_bus", "pcie", "pcie_phy", "pcie_aux"},
+		.mode_off[0] = IOMUXC_GPR12,
+		.mode_mask[0] = IMX6Q_GPR12_DEVICE_TYPE,
+		.mode_off[1] = IOMUXC_GPR12,
+		.mode_mask[1] = IMX8MQ_GPR12_PCIE2_CTRL_DEVICE_TYPE,
 	},
 	[IMX8MM] = {
 		.variant = IMX8MM,
@@ -1420,6 +1428,8 @@ static const struct imx6_pcie_drvdata drvdata[] = {
 			 IMX6_PCIE_FLAG_HAS_APP_RESET,
 		.gpr = "fsl,imx8mm-iomuxc-gpr",
 		.clk_names = {"pcie_bus", "pcie", "pcie_aux"},
+		.mode_off[0] = IOMUXC_GPR12,
+		.mode_mask[0] = IMX6Q_GPR12_DEVICE_TYPE,
 	},
 	[IMX8MP] = {
 		.variant = IMX8MP,
@@ -1428,6 +1438,8 @@ static const struct imx6_pcie_drvdata drvdata[] = {
 			 IMX6_PCIE_FLAG_HAS_APP_RESET,
 		.gpr = "fsl,imx8mp-iomuxc-gpr",
 		.clk_names = {"pcie_bus", "pcie", "pcie_aux"},
+		.mode_off[0] = IOMUXC_GPR12,
+		.mode_mask[0] = IMX6Q_GPR12_DEVICE_TYPE,
 	},
 	[IMX8MQ_EP] = {
 		.variant = IMX8MQ_EP,
@@ -1436,6 +1448,10 @@ static const struct imx6_pcie_drvdata drvdata[] = {
 		.mode = DW_PCIE_EP_TYPE,
 		.gpr = "fsl,imx8mq-iomuxc-gpr",
 		.clk_names = {"pcie_bus", "pcie", "pcie_phy", "pcie_aux"},
+		.mode_off[0] = IOMUXC_GPR12,
+		.mode_mask[0] = IMX6Q_GPR12_DEVICE_TYPE,
+		.mode_off[1] = IOMUXC_GPR12,
+		.mode_mask[1] = IMX8MQ_GPR12_PCIE2_CTRL_DEVICE_TYPE,
 	},
 	[IMX8MM_EP] = {
 		.variant = IMX8MM_EP,
@@ -1443,6 +1459,8 @@ static const struct imx6_pcie_drvdata drvdata[] = {
 		.mode = DW_PCIE_EP_TYPE,
 		.gpr = "fsl,imx8mm-iomuxc-gpr",
 		.clk_names = {"pcie_bus", "pcie", "pcie_aux"},
+		.mode_off[0] = IOMUXC_GPR12,
+		.mode_mask[0] = IMX6Q_GPR12_DEVICE_TYPE,
 	},
 	[IMX8MP_EP] = {
 		.variant = IMX8MP_EP,
@@ -1450,6 +1468,8 @@ static const struct imx6_pcie_drvdata drvdata[] = {
 		.mode = DW_PCIE_EP_TYPE,
 		.gpr = "fsl,imx8mp-iomuxc-gpr",
 		.clk_names = {"pcie_bus", "pcie", "pcie_aux"},
+		.mode_off[0] = IOMUXC_GPR12,
+		.mode_mask[0] = IMX6Q_GPR12_DEVICE_TYPE,
 	},
 };
 
-- 
2.34.1

[PATCH v5 08/16] PCI: imx6: Simplify switch-case logic by involve init_phy callback

[Frank Li]

Add drvdata::init_phy() callback function, so difference SOC choose
difference callback function to simple switch-case logic.

Signed-off-by: Frank Li <Frank.Li@nxp.com>
---

Notes:
    change from v1 to v4:
    - none

 drivers/pci/controller/dwc/pci-imx6.c | 135 ++++++++++++++------------
 1 file changed, 71 insertions(+), 64 deletions(-)

diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c
index 717e8fa030deb..d66a2db53bdb7 100644
--- a/drivers/pci/controller/dwc/pci-imx6.c
+++ b/drivers/pci/controller/dwc/pci-imx6.c
@@ -69,6 +69,9 @@ enum imx6_pcie_variants {
 #define IMX6_PCIE_MAX_CLKS       6
 
 #define IMX6_PCIE_MAX_INSTANCES			2
+
+struct imx6_pcie;
+
 struct imx6_pcie_drvdata {
 	enum imx6_pcie_variants variant;
 	enum dw_pcie_device_mode mode;
@@ -80,6 +83,7 @@ struct imx6_pcie_drvdata {
 	const u32 ltssm_mask;
 	const u32 mode_off[IMX6_PCIE_MAX_INSTANCES];
 	const u32 mode_mask[IMX6_PCIE_MAX_INSTANCES];
+	int (*init_phy)(struct imx6_pcie *pcie);
 };
 
 struct imx6_pcie {
@@ -323,76 +327,69 @@ static int pcie_phy_write(struct imx6_pcie *imx6_pcie, int addr, u16 data)
 	return 0;
 }
 
-static void imx6_pcie_init_phy(struct imx6_pcie *imx6_pcie)
+static int imx8mq_pcie_init_phy(struct imx6_pcie *imx6_pcie)
 {
-	switch (imx6_pcie->drvdata->variant) {
-	case IMX8MM:
-	case IMX8MM_EP:
-	case IMX8MP:
-	case IMX8MP_EP:
-		/*
-		 * The PHY initialization had been done in the PHY
-		 * driver, break here directly.
-		 */
-		break;
-	case IMX8MQ:
-	case IMX8MQ_EP:
-		/*
-		 * TODO: Currently this code assumes external
-		 * oscillator is being used
-		 */
+	/*
+	 * TODO: Currently this code assumes external
+	 * oscillator is being used
+	 */
+	regmap_update_bits(imx6_pcie->iomuxc_gpr,
+			   imx6_pcie_grp_offset(imx6_pcie),
+			   IMX8MQ_GPR_PCIE_REF_USE_PAD,
+			   IMX8MQ_GPR_PCIE_REF_USE_PAD);
+	/*
+	 * Regarding the datasheet, the PCIE_VPH is suggested
+	 * to be 1.8V. If the PCIE_VPH is supplied by 3.3V, the
+	 * VREG_BYPASS should be cleared to zero.
+	 */
+	if (imx6_pcie->vph && regulator_get_voltage(imx6_pcie->vph) > 3000000)
 		regmap_update_bits(imx6_pcie->iomuxc_gpr,
 				   imx6_pcie_grp_offset(imx6_pcie),
-				   IMX8MQ_GPR_PCIE_REF_USE_PAD,
-				   IMX8MQ_GPR_PCIE_REF_USE_PAD);
-		/*
-		 * Regarding the datasheet, the PCIE_VPH is suggested
-		 * to be 1.8V. If the PCIE_VPH is supplied by 3.3V, the
-		 * VREG_BYPASS should be cleared to zero.
-		 */
-		if (imx6_pcie->vph &&
-		    regulator_get_voltage(imx6_pcie->vph) > 3000000)
-			regmap_update_bits(imx6_pcie->iomuxc_gpr,
-					   imx6_pcie_grp_offset(imx6_pcie),
-					   IMX8MQ_GPR_PCIE_VREG_BYPASS,
-					   0);
-		break;
-	case IMX7D:
-		regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
+				   IMX8MQ_GPR_PCIE_VREG_BYPASS,
+				   0);
+
+	return 0;
+}
+
+static int imx7d_pcie_init_phy(struct imx6_pcie *imx6_pcie)
+{
+	return	regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
 				   IMX7D_GPR12_PCIE_PHY_REFCLK_SEL, 0);
-		break;
-	case IMX6SX:
-		regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
-				   IMX6SX_GPR12_PCIE_RX_EQ_MASK,
-				   IMX6SX_GPR12_PCIE_RX_EQ_2);
-		fallthrough;
-	default:
-		regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
+}
+
+static int imx6_pcie_init_phy(struct imx6_pcie *imx6_pcie)
+{
+	regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
 				   IMX6Q_GPR12_PCIE_CTL_2, 0 << 10);
 
-		/* configure constant input signal to the pcie ctrl and phy */
-		regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
-				   IMX6Q_GPR12_LOS_LEVEL, 9 << 4);
-
-		regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR8,
-				   IMX6Q_GPR8_TX_DEEMPH_GEN1,
-				   imx6_pcie->tx_deemph_gen1 << 0);
-		regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR8,
-				   IMX6Q_GPR8_TX_DEEMPH_GEN2_3P5DB,
-				   imx6_pcie->tx_deemph_gen2_3p5db << 6);
-		regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR8,
-				   IMX6Q_GPR8_TX_DEEMPH_GEN2_6DB,
-				   imx6_pcie->tx_deemph_gen2_6db << 12);
-		regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR8,
-				   IMX6Q_GPR8_TX_SWING_FULL,
-				   imx6_pcie->tx_swing_full << 18);
-		regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR8,
-				   IMX6Q_GPR8_TX_SWING_LOW,
-				   imx6_pcie->tx_swing_low << 25);
-		break;
-	}
+	/* configure constant input signal to the pcie ctrl and phy */
+	regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
+			   IMX6Q_GPR12_LOS_LEVEL, 9 << 4);
+
+	regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR8,
+			   IMX6Q_GPR8_TX_DEEMPH_GEN1,
+			   imx6_pcie->tx_deemph_gen1 << 0);
+	regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR8,
+			   IMX6Q_GPR8_TX_DEEMPH_GEN2_3P5DB,
+			   imx6_pcie->tx_deemph_gen2_3p5db << 6);
+	regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR8,
+			   IMX6Q_GPR8_TX_DEEMPH_GEN2_6DB,
+			   imx6_pcie->tx_deemph_gen2_6db << 12);
+	regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR8,
+			   IMX6Q_GPR8_TX_SWING_FULL,
+			   imx6_pcie->tx_swing_full << 18);
+	regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR8,
+			   IMX6Q_GPR8_TX_SWING_LOW,
+			   imx6_pcie->tx_swing_low << 25);
+	return 0;
+}
 
-	imx6_pcie_configure_type(imx6_pcie);
+static int imx6sx_pcie_init_phy(struct imx6_pcie *imx6_pcie)
+{
+	regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
+			   IMX6SX_GPR12_PCIE_RX_EQ_MASK, IMX6SX_GPR12_PCIE_RX_EQ_2);
+
+	return imx6_pcie_init_phy(imx6_pcie);
 }
 
 static void imx7d_pcie_wait_for_phy_pll_lock(struct imx6_pcie *imx6_pcie)
@@ -903,7 +900,11 @@ static int imx6_pcie_host_init(struct dw_pcie_rp *pp)
 	}
 
 	imx6_pcie_assert_core_reset(imx6_pcie);
-	imx6_pcie_init_phy(imx6_pcie);
+
+	if (imx6_pcie->drvdata->init_phy)
+		imx6_pcie->drvdata->init_phy(imx6_pcie);
+
+	imx6_pcie_configure_type(imx6_pcie);
 
 	ret = imx6_pcie_clk_enable(imx6_pcie);
 	if (ret) {
@@ -1374,6 +1375,7 @@ static const struct imx6_pcie_drvdata drvdata[] = {
 		.ltssm_mask = IMX6Q_GPR12_PCIE_CTL_2,
 		.mode_off[0] = IOMUXC_GPR12,
 		.mode_mask[0] = IMX6Q_GPR12_DEVICE_TYPE,
+		.init_phy = imx6_pcie_init_phy,
 	},
 	[IMX6SX] = {
 		.variant = IMX6SX,
@@ -1386,6 +1388,7 @@ static const struct imx6_pcie_drvdata drvdata[] = {
 		.ltssm_mask = IMX6Q_GPR12_PCIE_CTL_2,
 		.mode_off[0] = IOMUXC_GPR12,
 		.mode_mask[0] = IMX6Q_GPR12_DEVICE_TYPE,
+		.init_phy = imx6sx_pcie_init_phy,
 	},
 	[IMX6QP] = {
 		.variant = IMX6QP,
@@ -1399,6 +1402,7 @@ static const struct imx6_pcie_drvdata drvdata[] = {
 		.ltssm_mask = IMX6Q_GPR12_PCIE_CTL_2,
 		.mode_off[0] = IOMUXC_GPR12,
 		.mode_mask[0] = IMX6Q_GPR12_DEVICE_TYPE,
+		.init_phy = imx6_pcie_init_phy,
 	},
 	[IMX7D] = {
 		.variant = IMX7D,
@@ -1409,6 +1413,7 @@ static const struct imx6_pcie_drvdata drvdata[] = {
 		.clk_names = {"pcie_bus", "pcie", "pcie_phy"},
 		.mode_off[0] = IOMUXC_GPR12,
 		.mode_mask[0] = IMX6Q_GPR12_DEVICE_TYPE,
+		.init_phy = imx7d_pcie_init_phy,
 	},
 	[IMX8MQ] = {
 		.variant = IMX8MQ,
@@ -1420,6 +1425,7 @@ static const struct imx6_pcie_drvdata drvdata[] = {
 		.mode_mask[0] = IMX6Q_GPR12_DEVICE_TYPE,
 		.mode_off[1] = IOMUXC_GPR12,
 		.mode_mask[1] = IMX8MQ_GPR12_PCIE2_CTRL_DEVICE_TYPE,
+		.init_phy = imx8mq_pcie_init_phy,
 	},
 	[IMX8MM] = {
 		.variant = IMX8MM,
@@ -1452,6 +1458,7 @@ static const struct imx6_pcie_drvdata drvdata[] = {
 		.mode_mask[0] = IMX6Q_GPR12_DEVICE_TYPE,
 		.mode_off[1] = IOMUXC_GPR12,
 		.mode_mask[1] = IMX8MQ_GPR12_PCIE2_CTRL_DEVICE_TYPE,
+		.init_phy = imx8mq_pcie_init_phy,
 	},
 	[IMX8MM_EP] = {
 		.variant = IMX8MM_EP,
-- 
2.34.1

[PATCH v5 09/16] dt-bindings: imx6q-pcie: Clean up irrationality clocks check

[Frank Li]

There are clocks and clock-names restriction for difference compatible
string. So needn't irrationality check again for clock's miniItems and
maxItems.

Signed-off-by: Frank Li <Frank.Li@nxp.com>
---

Notes:
    Change from v1 to v4
    - new patch at v4

 .../bindings/pci/fsl,imx6q-pcie-common.yaml      | 16 ----------------
 1 file changed, 16 deletions(-)

diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie-common.yaml b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie-common.yaml
index 8f39b4e6e8491..a284a27c5e873 100644
--- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie-common.yaml
+++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie-common.yaml
@@ -150,22 +150,6 @@ allOf:
             - {}
             - const: pcie_phy
             - const: pcie_aux
-  - if:
-      properties:
-        compatible:
-          not:
-            contains:
-              enum:
-                - fsl,imx6sx-pcie
-                - fsl,imx8mq-pcie
-                - fsl,imx6sx-pcie-ep
-                - fsl,imx8mq-pcie-ep
-    then:
-      properties:
-        clocks:
-          maxItems: 3
-        clock-names:
-          maxItems: 3
 
   - if:
       properties:
-- 
2.34.1

Re: [PATCH v5 09/16] dt-bindings: imx6q-pcie: Clean up irrationality clocks check

[Krzysztof Kozlowski]

On 20/12/2023 22:36, Frank Li wrote:
> There are clocks and clock-names restriction for difference compatible
> string. So needn't irrationality check again for clock's miniItems and
> maxItems.

That's not really true. Other entry does not restrict clocks and leave
items quite flexible. These entries should be combined so all
constraints are fixed for all variants.

Best regards,
Krzysztof

Re: [PATCH v5 09/16] dt-bindings: imx6q-pcie: Clean up irrationality clocks check

[Frank Li]

On Sat, Dec 23, 2023 at 07:42:12PM +0100, Krzysztof Kozlowski wrote:
> On 20/12/2023 22:36, Frank Li wrote:
> > There are clocks and clock-names restriction for difference compatible
> > string. So needn't irrationality check again for clock's miniItems and
> > maxItems.
> 
> That's not really true. Other entry does not restrict clocks and leave
> items quite flexible. These entries should be combined so all
> constraints are fixed for all variants.

There are 7 compatible string at pci/fsl,imx6q-pcie.yaml 

- fsl,imx6q-pcie                                                     
      - fsl,imx6sx-pcie                                                    
      - fsl,imx6qp-pcie                                                    
      - fsl,imx7d-pcie                                                     
      - fsl,imx8mq-pcie                                                    
      - fsl,imx8mm-pcie                                                    
      - fsl,imx8mp-pcie                                                    
      - fsl,imx95-pcie                                                     
                      
All 7 compatible string have check

 - if:                                                                    
      properties:                                                          
        compatible:                                                        
          enum:                                                            
            - fsl,imx6sx-pcie
...
- if:                                                                    
      properties:                                                          
        compatible:                                                        
          enum:                                                            
            - fsl,imx8mq-pcie

...
- if:                                                                    
      properties:                                                          
        compatible:                                                        
          enum:                                                            
            - fsl,imx6q-pcie                                               
            - fsl,imx6qp-pcie                                              
            - fsl,imx7d-pcie
...
  - if:                                                                    
      properties:                                                          
        compatible:                                                        
          enum:                                                            
            - fsl,imx8mm-pcie                                              
            - fsl,imx8mp-pcie
...

This check was not necessary at all. 

> 
> Best regards,
> Krzysztof
> 

Re: [PATCH v5 09/16] dt-bindings: imx6q-pcie: Clean up irrationality clocks check

[Krzysztof Kozlowski]

On 24/12/2023 05:43, Frank Li wrote:
> On Sat, Dec 23, 2023 at 07:42:12PM +0100, Krzysztof Kozlowski wrote:
>> On 20/12/2023 22:36, Frank Li wrote:
>>> There are clocks and clock-names restriction for difference compatible
>>> string. So needn't irrationality check again for clock's miniItems and
>>> maxItems.
>>
>> That's not really true. Other entry does not restrict clocks and leave
>> items quite flexible. These entries should be combined so all
>> constraints are fixed for all variants.
> 
> There are 7 compatible string at pci/fsl,imx6q-pcie.yaml 

Then explain it in the commit msg. The file you are touching has
something entirely else.

And what about -ep binding? Commit msg explains nothing here as well.


Best regards,
Krzysztof

[PATCH v5 10/16] dt-bindings: imx6q-pcie: remove reg and reg-name

[Frank Li]

snps,dw-pcie.yaml already have reg and reg-name information. Needn't
duplciate here.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---

Notes:
    Change from v4 to v5
    - add Rob's Acked
    Change from v1 to v4:
    - new patch at v4

 .../devicetree/bindings/pci/fsl,imx6q-pcie.yaml        | 10 ----------
 1 file changed, 10 deletions(-)

diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
index 81bbb8728f0f9..f20d4f0e3cb6c 100644
--- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
+++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
@@ -30,16 +30,6 @@ properties:
       - fsl,imx8mm-pcie
       - fsl,imx8mp-pcie
 
-  reg:
-    items:
-      - description: Data Bus Interface (DBI) registers.
-      - description: PCIe configuration space region.
-
-  reg-names:
-    items:
-      - const: dbi
-      - const: config
-
   clocks:
     minItems: 3
     items:
-- 
2.34.1

Re: [PATCH v5 10/16] dt-bindings: imx6q-pcie: remove reg and reg-name

[Rob Herring]

On Wed, Dec 20, 2023 at 04:36:09PM -0500, Frank Li wrote:
> snps,dw-pcie.yaml already have reg and reg-name information. Needn't
> duplciate here.
> 
> Acked-by: Rob Herring <robh@kernel.org>
> Signed-off-by: Frank Li <Frank.Li@nxp.com>
> ---
> 
> Notes:
>     Change from v4 to v5
>     - add Rob's Acked

Err, that was intended for patch 9, not this one. This patch should be 
dropped.

>     Change from v1 to v4:
>     - new patch at v4
> 
>  .../devicetree/bindings/pci/fsl,imx6q-pcie.yaml        | 10 ----------
>  1 file changed, 10 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
> index 81bbb8728f0f9..f20d4f0e3cb6c 100644
> --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
> +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
> @@ -30,16 +30,6 @@ properties:
>        - fsl,imx8mm-pcie
>        - fsl,imx8mp-pcie
>  
> -  reg:
> -    items:
> -      - description: Data Bus Interface (DBI) registers.
> -      - description: PCIe configuration space region.
> -
> -  reg-names:
> -    items:
> -      - const: dbi
> -      - const: config
> -
>    clocks:
>      minItems: 3
>      items:
> -- 
> 2.34.1
> 

Re: [PATCH v5 10/16] dt-bindings: imx6q-pcie: remove reg and reg-name

[Frank Li]

On Thu, Dec 21, 2023 at 04:50:33PM -0600, Rob Herring wrote:
> On Wed, Dec 20, 2023 at 04:36:09PM -0500, Frank Li wrote:
> > snps,dw-pcie.yaml already have reg and reg-name information. Needn't
> > duplciate here.
> > 
> > Acked-by: Rob Herring <robh@kernel.org>
> > Signed-off-by: Frank Li <Frank.Li@nxp.com>
> > ---
> > 
> > Notes:
> >     Change from v4 to v5
> >     - add Rob's Acked
> 
> Err, that was intended for patch 9, not this one. This patch should be 
> dropped.

Sorry, will correct it.

Actually I want to move it under Allof

if compatiable string (A, B, C...)
then
	reg-names:
		-const: dbi
		-const: config

Differece SOC have difference reg-names required list. If split it, it
will be easy when add new SOC. Needn't change two place.

Let me update at next version.


> 
> >     Change from v1 to v4:
> >     - new patch at v4
> > 
> >  .../devicetree/bindings/pci/fsl,imx6q-pcie.yaml        | 10 ----------
> >  1 file changed, 10 deletions(-)
> > 
> > diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
> > index 81bbb8728f0f9..f20d4f0e3cb6c 100644
> > --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
> > +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
> > @@ -30,16 +30,6 @@ properties:
> >        - fsl,imx8mm-pcie
> >        - fsl,imx8mp-pcie
> >  
> > -  reg:
> > -    items:
> > -      - description: Data Bus Interface (DBI) registers.
> > -      - description: PCIe configuration space region.
> > -
> > -  reg-names:
> > -    items:
> > -      - const: dbi
> > -      - const: config
> > -
> >    clocks:
> >      minItems: 3
> >      items:
> > -- 
> > 2.34.1
> > 

Re: [PATCH v5 10/16] dt-bindings: imx6q-pcie: remove reg and reg-name

[Krzysztof Kozlowski]

On 23/12/2023 04:46, Frank Li wrote:
> On Thu, Dec 21, 2023 at 04:50:33PM -0600, Rob Herring wrote:
>> On Wed, Dec 20, 2023 at 04:36:09PM -0500, Frank Li wrote:
>>> snps,dw-pcie.yaml already have reg and reg-name information. Needn't
>>> duplciate here.
>>>
>>> Acked-by: Rob Herring <robh@kernel.org>
>>> Signed-off-by: Frank Li <Frank.Li@nxp.com>
>>> ---
>>>
>>> Notes:
>>>     Change from v4 to v5
>>>     - add Rob's Acked
>>
>> Err, that was intended for patch 9, not this one. This patch should be 
>> dropped.
> 
> Sorry, will correct it.
> 
> Actually I want to move it under Allof
> 
> if compatiable string (A, B, C...)
> then
> 	reg-names:
> 		-const: dbi
> 		-const: config
> 
> Differece SOC have difference reg-names required list. If split it, it
> will be easy when add new SOC. Needn't change two place.
> 
> Let me update at next version.
> 

This patch should be dropped. Why do you remove entries from top-level?
Are they defined in other schema?

Best regards,
Krzysztof

Re: [PATCH v5 10/16] dt-bindings: imx6q-pcie: remove reg and reg-name

[Frank Li]

On Sat, Dec 23, 2023 at 07:43:01PM +0100, Krzysztof Kozlowski wrote:
> On 23/12/2023 04:46, Frank Li wrote:
> > On Thu, Dec 21, 2023 at 04:50:33PM -0600, Rob Herring wrote:
> >> On Wed, Dec 20, 2023 at 04:36:09PM -0500, Frank Li wrote:
> >>> snps,dw-pcie.yaml already have reg and reg-name information. Needn't
> >>> duplciate here.
> >>>
> >>> Acked-by: Rob Herring <robh@kernel.org>
> >>> Signed-off-by: Frank Li <Frank.Li@nxp.com>
> >>> ---
> >>>
> >>> Notes:
> >>>     Change from v4 to v5
> >>>     - add Rob's Acked
> >>
> >> Err, that was intended for patch 9, not this one. This patch should be 
> >> dropped.
> > 
> > Sorry, will correct it.
> > 
> > Actually I want to move it under Allof
> > 
> > if compatiable string (A, B, C...)
> > then
> > 	reg-names:
> > 		-const: dbi
> > 		-const: config
> > 
> > Differece SOC have difference reg-names required list. If split it, it
> > will be easy when add new SOC. Needn't change two place.
> > 
> > Let me update at next version.
> > 
> 
> This patch should be dropped. Why do you remove entries from top-level?
> Are they defined in other schema?

pci/snps,dw-pcie.yaml already define it.

Frank

> 
> Best regards,
> Krzysztof
> 

Re: [PATCH v5 10/16] dt-bindings: imx6q-pcie: remove reg and reg-name

[Krzysztof Kozlowski]

On 24/12/2023 05:34, Frank Li wrote:
> On Sat, Dec 23, 2023 at 07:43:01PM +0100, Krzysztof Kozlowski wrote:
>> On 23/12/2023 04:46, Frank Li wrote:
>>> On Thu, Dec 21, 2023 at 04:50:33PM -0600, Rob Herring wrote:
>>>> On Wed, Dec 20, 2023 at 04:36:09PM -0500, Frank Li wrote:
>>>>> snps,dw-pcie.yaml already have reg and reg-name information. Needn't
>>>>> duplciate here.
>>>>>
>>>>> Acked-by: Rob Herring <robh@kernel.org>
>>>>> Signed-off-by: Frank Li <Frank.Li@nxp.com>
>>>>> ---
>>>>>
>>>>> Notes:
>>>>>     Change from v4 to v5
>>>>>     - add Rob's Acked
>>>>
>>>> Err, that was intended for patch 9, not this one. This patch should be 
>>>> dropped.
>>>
>>> Sorry, will correct it.
>>>
>>> Actually I want to move it under Allof
>>>
>>> if compatiable string (A, B, C...)
>>> then
>>> 	reg-names:
>>> 		-const: dbi
>>> 		-const: config
>>>
>>> Differece SOC have difference reg-names required list. If split it, it
>>> will be easy when add new SOC. Needn't change two place.
>>>
>>> Let me update at next version.
>>>
>>
>> This patch should be dropped. Why do you remove entries from top-level?
>> Are they defined in other schema?
> 
> pci/snps,dw-pcie.yaml already define it.

Indeed I see you wrote it in commit msg. However snps,dwc-pcie has it in
 an unconstrained way. Nothing in commit msg suggests there are
constrains somewhere.

Best regards,
Krzysztof

[PATCH v5 11/16] dt-bindings: imx6q-pcie: Add imx95 pcie compatible string

[Frank Li]

From: Richard Zhu <hongxing.zhu@nxp.com>

Add i.MX95 PCIe "fsl,imx95-pcie" compatible string.
Add "atu" and "app" to reg-names.

Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
---

Notes:
    Change from v2 to v3
    - Remove krzy's ACK tag
    - Add condition check for imx95, which required more reg-names then old
    platform, so need Krzy review again,
    
    Change from v1 to v2
    - add Krzy's ACK tag

 .../bindings/pci/fsl,imx6q-pcie-common.yaml    |  1 +
 .../bindings/pci/fsl,imx6q-pcie.yaml           | 18 ++++++++++++++++++
 2 files changed, 19 insertions(+)

diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie-common.yaml b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie-common.yaml
index a284a27c5e873..1b63089ff0aee 100644
--- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie-common.yaml
+++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie-common.yaml
@@ -207,6 +207,7 @@ allOf:
                 - fsl,imx6sx-pcie
                 - fsl,imx6q-pcie
                 - fsl,imx6qp-pcie
+                - fsl,imx95-pcie
                 - fsl,imx6sx-pcie-ep
                 - fsl,imx6q-pcie-ep
                 - fsl,imx6qp-pcie-ep
diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
index f20d4f0e3cb6c..8633c622bd178 100644
--- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
+++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
@@ -29,6 +29,7 @@ properties:
       - fsl,imx8mq-pcie
       - fsl,imx8mm-pcie
       - fsl,imx8mp-pcie
+      - fsl,imx95-pcie
 
   clocks:
     minItems: 3
@@ -80,6 +81,22 @@ required:
 allOf:
   - $ref: /schemas/pci/snps,dw-pcie.yaml#
   - $ref: /schemas/pci/fsl,imx6q-pcie-common.yaml#
+  - if:
+      properties:
+        compatible:
+          enum:
+            - fsl,imx95-pcie
+    then:
+      properties:
+        reg:
+          minItems: 4
+        reg-names:
+          items:
+            - const: dbi
+            - const: atu
+            - const: app
+            - const: config
+
   - if:
       properties:
         compatible:
@@ -101,6 +118,7 @@ allOf:
         compatible:
           enum:
             - fsl,imx8mq-pcie
+            - fsl,imx95-pcie
     then:
       properties:
         clocks:
-- 
2.34.1

Re: [PATCH v5 11/16] dt-bindings: imx6q-pcie: Add imx95 pcie compatible string

[Rob Herring]

On Wed, Dec 20, 2023 at 04:36:10PM -0500, Frank Li wrote:
> From: Richard Zhu <hongxing.zhu@nxp.com>
> 
> Add i.MX95 PCIe "fsl,imx95-pcie" compatible string.
> Add "atu" and "app" to reg-names.
> 
> Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
> ---
> 
> Notes:
>     Change from v2 to v3
>     - Remove krzy's ACK tag
>     - Add condition check for imx95, which required more reg-names then old
>     platform, so need Krzy review again,
>     
>     Change from v1 to v2
>     - add Krzy's ACK tag
> 
>  .../bindings/pci/fsl,imx6q-pcie-common.yaml    |  1 +
>  .../bindings/pci/fsl,imx6q-pcie.yaml           | 18 ++++++++++++++++++
>  2 files changed, 19 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie-common.yaml b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie-common.yaml
> index a284a27c5e873..1b63089ff0aee 100644
> --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie-common.yaml
> +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie-common.yaml
> @@ -207,6 +207,7 @@ allOf:
>                  - fsl,imx6sx-pcie
>                  - fsl,imx6q-pcie
>                  - fsl,imx6qp-pcie
> +                - fsl,imx95-pcie
>                  - fsl,imx6sx-pcie-ep
>                  - fsl,imx6q-pcie-ep
>                  - fsl,imx6qp-pcie-ep
> diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
> index f20d4f0e3cb6c..8633c622bd178 100644
> --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
> +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
> @@ -29,6 +29,7 @@ properties:
>        - fsl,imx8mq-pcie
>        - fsl,imx8mm-pcie
>        - fsl,imx8mp-pcie
> +      - fsl,imx95-pcie
>  
>    clocks:
>      minItems: 3
> @@ -80,6 +81,22 @@ required:
>  allOf:
>    - $ref: /schemas/pci/snps,dw-pcie.yaml#
>    - $ref: /schemas/pci/fsl,imx6q-pcie-common.yaml#
> +  - if:
> +      properties:
> +        compatible:
> +          enum:
> +            - fsl,imx95-pcie
> +    then:
> +      properties:
> +        reg:
> +          minItems: 4
> +        reg-names:
> +          items:
> +            - const: dbi
> +            - const: atu
> +            - const: app
> +            - const: config

Add new entries to the end. Originally, you had dbi and config. Add ata 
and app on the end.

> +
>    - if:
>        properties:
>          compatible:
> @@ -101,6 +118,7 @@ allOf:
>          compatible:
>            enum:
>              - fsl,imx8mq-pcie
> +            - fsl,imx95-pcie
>      then:
>        properties:
>          clocks:
> -- 
> 2.34.1
> 

[PATCH v5 12/16] PCI: imx6: Add iMX95 PCIe support

[Frank Li]

Add iMX95 PCIe basic root complex function support.

Signed-off-by: Frank Li <Frank.Li@nxp.com>
---

Notes:
    Change from v1 to v3
    - none

 drivers/pci/controller/dwc/pci-imx6.c | 90 +++++++++++++++++++++++++--
 1 file changed, 85 insertions(+), 5 deletions(-)

diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c
index d66a2db53bdb7..9e60ab6f1885a 100644
--- a/drivers/pci/controller/dwc/pci-imx6.c
+++ b/drivers/pci/controller/dwc/pci-imx6.c
@@ -42,6 +42,25 @@
 #define IMX8MQ_GPR_PCIE_VREG_BYPASS		BIT(12)
 #define IMX8MQ_GPR12_PCIE2_CTRL_DEVICE_TYPE	GENMASK(11, 8)
 
+#define IMX95_PCIE_PHY_GEN_CTRL			0x0
+#define IMX95_PCIE_REF_USE_PAD			BIT(17)
+
+#define IMX95_PCIE_PHY_MPLLA_CTRL		0x10
+#define IMX95_PCIE_PHY_MPLL_STATE		BIT(30)
+
+#define IMX95_PCIE_SS_RW_REG_0			0xf0
+#define IMX95_PCIE_REF_CLKEN			BIT(23)
+#define IMX95_PCIE_PHY_CR_PARA_SEL		BIT(9)
+
+#define IMX95_PE0_GEN_CTRL_1			0x1050
+#define IMX95_PCIE_DEVICE_TYPE			GENMASK(3, 0)
+
+#define IMX95_PE0_GEN_CTRL_3			0x1058
+#define IMX95_PCIE_LTSSM_EN			BIT(0)
+
+#define IMX95_PE0_PM_STS			0x1064
+#define IMX95_PCIE_PM_LINKST_IN_L2		BIT(14)
+
 #define to_imx6_pcie(x)	dev_get_drvdata((x)->dev)
 
 enum imx6_pcie_variants {
@@ -52,6 +71,7 @@ enum imx6_pcie_variants {
 	IMX8MQ,
 	IMX8MM,
 	IMX8MP,
+	IMX95,
 	IMX8MQ_EP,
 	IMX8MM_EP,
 	IMX8MP_EP,
@@ -63,6 +83,7 @@ enum imx6_pcie_variants {
 #define IMX6_PCIE_FLAG_HAS_PHY			BIT(3)
 #define IMX6_PCIE_FLAG_HAS_APP_RESET		BIT(4)
 #define IMX6_PCIE_FLAG_HAS_PHY_RESET		BIT(5)
+#define IMX6_PCIE_FLAG_HAS_SERDES		BIT(6)
 
 #define imx6_check_flag(pci, val)     (pci->drvdata->flags & val)
 
@@ -179,6 +200,24 @@ static unsigned int imx6_pcie_grp_offset(const struct imx6_pcie *imx6_pcie)
 	return imx6_pcie->controller_id == 1 ? IOMUXC_GPR16 : IOMUXC_GPR14;
 }
 
+static int imx95_pcie_init_phy(struct imx6_pcie *imx6_pcie)
+{
+	regmap_update_bits(imx6_pcie->iomuxc_gpr,
+			IMX95_PCIE_SS_RW_REG_0,
+			IMX95_PCIE_PHY_CR_PARA_SEL,
+			IMX95_PCIE_PHY_CR_PARA_SEL);
+
+	regmap_update_bits(imx6_pcie->iomuxc_gpr,
+			   IMX95_PCIE_PHY_GEN_CTRL,
+			   IMX95_PCIE_REF_USE_PAD, 0);
+	regmap_update_bits(imx6_pcie->iomuxc_gpr,
+			   IMX95_PCIE_SS_RW_REG_0,
+			   IMX95_PCIE_REF_CLKEN,
+			   IMX95_PCIE_REF_CLKEN);
+
+	return 0;
+}
+
 static void imx6_pcie_configure_type(struct imx6_pcie *imx6_pcie)
 {
 	const struct imx6_pcie_drvdata *drvdata = imx6_pcie->drvdata;
@@ -579,6 +618,7 @@ static int imx6_pcie_enable_ref_clk(struct imx6_pcie *imx6_pcie)
 				   IMX6Q_GPR1_PCIE_REF_CLK_EN, 1 << 16);
 		break;
 	case IMX7D:
+	case IMX95:
 		break;
 	case IMX8MM:
 	case IMX8MM_EP:
@@ -696,10 +736,19 @@ static int imx6_pcie_deassert_core_reset(struct imx6_pcie *imx6_pcie)
 {
 	struct dw_pcie *pci = imx6_pcie->pci;
 	struct device *dev = pci->dev;
+	u32 val;
 
 	reset_control_deassert(imx6_pcie->pciephy_reset);
 
 	switch (imx6_pcie->drvdata->variant) {
+	case IMX95:
+		/* Polling the MPLL_STATE */
+		if (regmap_read_poll_timeout(imx6_pcie->iomuxc_gpr,
+					IMX95_PCIE_PHY_MPLLA_CTRL, val,
+					val & IMX95_PCIE_PHY_MPLL_STATE,
+					10, 10000))
+			dev_err(dev, "PCIe PLL lock timeout\n");
+		break;
 	case IMX7D:
 		/* Workaround for ERR010728, failure of PCI-e PLL VCO to
 		 * oscillate, especially when cold.  This turns off "Duty-cycle
@@ -1281,12 +1330,32 @@ static int imx6_pcie_probe(struct platform_device *pdev)
 		return PTR_ERR(imx6_pcie->turnoff_reset);
 	}
 
+	if (imx6_pcie->drvdata->gpr) {
 	/* Grab GPR config register range */
-	imx6_pcie->iomuxc_gpr =
-		 syscon_regmap_lookup_by_compatible(imx6_pcie->drvdata->gpr);
-	if (IS_ERR(imx6_pcie->iomuxc_gpr)) {
-		dev_err(dev, "unable to find iomuxc registers\n");
-		return PTR_ERR(imx6_pcie->iomuxc_gpr);
+		imx6_pcie->iomuxc_gpr =
+			 syscon_regmap_lookup_by_compatible(imx6_pcie->drvdata->gpr);
+		if (IS_ERR(imx6_pcie->iomuxc_gpr))
+			return dev_err_probe(dev, PTR_ERR(imx6_pcie->iomuxc_gpr),
+					     "unable to find iomuxc registers\n");
+	}
+
+	if (imx6_check_flag(imx6_pcie, IMX6_PCIE_FLAG_HAS_SERDES)) {
+		void __iomem *off = devm_platform_ioremap_resource_byname(pdev, "app");
+
+		if (IS_ERR(off))
+			return dev_err_probe(dev, PTR_ERR(off),
+					     "unable to find serdes registers\n");
+
+		static struct regmap_config regmap_config = {
+			.reg_bits = 32,
+			.val_bits = 32,
+			.reg_stride = 4,
+		};
+
+		imx6_pcie->iomuxc_gpr = devm_regmap_init_mmio(dev, off, &regmap_config);
+		if (IS_ERR(imx6_pcie->iomuxc_gpr))
+			return dev_err_probe(dev, PTR_ERR(imx6_pcie->iomuxc_gpr),
+					     "unable to find iomuxc registers\n");
 	}
 
 	/* Grab PCIe PHY Tx Settings */
@@ -1447,6 +1516,16 @@ static const struct imx6_pcie_drvdata drvdata[] = {
 		.mode_off[0] = IOMUXC_GPR12,
 		.mode_mask[0] = IMX6Q_GPR12_DEVICE_TYPE,
 	},
+	[IMX95] = {
+		.variant = IMX95,
+		.flags = IMX6_PCIE_FLAG_HAS_SERDES,
+		.clk_names = {"pcie_bus", "pcie", "pcie_phy", "pcie_aux"},
+		.ltssm_off = IMX95_PE0_GEN_CTRL_3,
+		.ltssm_mask = IMX95_PCIE_LTSSM_EN,
+		.mode_off[0]  = IMX95_PE0_GEN_CTRL_1,
+		.mode_mask[0] = IMX95_PCIE_DEVICE_TYPE,
+		.init_phy = imx95_pcie_init_phy,
+	},
 	[IMX8MQ_EP] = {
 		.variant = IMX8MQ_EP,
 		.flags = IMX6_PCIE_FLAG_HAS_APP_RESET |
@@ -1488,6 +1567,7 @@ static const struct of_device_id imx6_pcie_of_match[] = {
 	{ .compatible = "fsl,imx8mq-pcie", .data = &drvdata[IMX8MQ], },
 	{ .compatible = "fsl,imx8mm-pcie", .data = &drvdata[IMX8MM], },
 	{ .compatible = "fsl,imx8mp-pcie", .data = &drvdata[IMX8MP], },
+	{ .compatible = "fsl,imx95-pcie", .data = &drvdata[IMX95], },
 	{ .compatible = "fsl,imx8mq-pcie-ep", .data = &drvdata[IMX8MQ_EP], },
 	{ .compatible = "fsl,imx8mm-pcie-ep", .data = &drvdata[IMX8MM_EP], },
 	{ .compatible = "fsl,imx8mp-pcie-ep", .data = &drvdata[IMX8MP_EP], },
-- 
2.34.1

[PATCH v5 13/16] PCI: imx6: Clean up get addr_space code

[Frank Li]

The common dw_pcie_ep_init() already do the same thing. Needn't platform
driver do it again.

Signed-off-by: Frank Li <Frank.Li@nxp.com>
---

Notes:
    Change from v1 to v3
    - new patches

 drivers/pci/controller/dwc/pci-imx6.c | 9 +--------
 1 file changed, 1 insertion(+), 8 deletions(-)

diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c
index 9e60ab6f1885a..4b2b9aafad1b4 100644
--- a/drivers/pci/controller/dwc/pci-imx6.c
+++ b/drivers/pci/controller/dwc/pci-imx6.c
@@ -1080,7 +1080,6 @@ static int imx6_add_pcie_ep(struct imx6_pcie *imx6_pcie,
 	int ret;
 	unsigned int pcie_dbi2_offset;
 	struct dw_pcie_ep *ep;
-	struct resource *res;
 	struct dw_pcie *pci = imx6_pcie->pci;
 	struct dw_pcie_rp *pp = &pci->pp;
 	struct device *dev = pci->dev;
@@ -1099,14 +1098,8 @@ static int imx6_add_pcie_ep(struct imx6_pcie *imx6_pcie,
 		pcie_dbi2_offset = SZ_4K;
 		break;
 	}
-	pci->dbi_base2 = pci->dbi_base + pcie_dbi2_offset;
-	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "addr_space");
-	if (!res)
-		return -EINVAL;
 
-	ep->phys_base = res->start;
-	ep->addr_size = resource_size(res);
-	ep->page_size = SZ_64K;
+	pci->dbi_base2 = pci->dbi_base + pcie_dbi2_offset;
 
 	ret = dw_pcie_ep_init(ep);
 	if (ret) {
-- 
2.34.1

[PATCH v5 14/16] PCI: imx6: Add epc_features in imx6_pcie_drvdata

[Frank Li]

The i.MX EP exhibits variations in epc_features among different EP
configurations. This introduces the addition of epc_features in
imx6_pcie_drvdata to accommodate these differences. It's important to note
that there are no functional changes in this commit; instead, it lays the
groundwork for supporting i.MX95 EP functions.

Signed-off-by: Frank Li <Frank.Li@nxp.com>
---

Notes:
    Change from v1 to v3
    - new patch at v3

 drivers/pci/controller/dwc/pci-imx6.c | 9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)

diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c
index 4b2b9aafad1b4..6a58fd63a9dd2 100644
--- a/drivers/pci/controller/dwc/pci-imx6.c
+++ b/drivers/pci/controller/dwc/pci-imx6.c
@@ -104,6 +104,7 @@ struct imx6_pcie_drvdata {
 	const u32 ltssm_mask;
 	const u32 mode_off[IMX6_PCIE_MAX_INSTANCES];
 	const u32 mode_mask[IMX6_PCIE_MAX_INSTANCES];
+	const struct pci_epc_features *epc_features;
 	int (*init_phy)(struct imx6_pcie *pcie);
 };
 
@@ -1065,7 +1066,10 @@ static const struct pci_epc_features imx8m_pcie_epc_features = {
 static const struct pci_epc_features*
 imx6_pcie_ep_get_features(struct dw_pcie_ep *ep)
 {
-	return &imx8m_pcie_epc_features;
+	struct dw_pcie *pci = to_dw_pcie_from_ep(ep);
+	struct imx6_pcie *imx6_pcie = to_imx6_pcie(pci);
+
+	return imx6_pcie->drvdata->epc_features;
 }
 
 static const struct dw_pcie_ep_ops pcie_ep_ops = {
@@ -1530,6 +1534,7 @@ static const struct imx6_pcie_drvdata drvdata[] = {
 		.mode_mask[0] = IMX6Q_GPR12_DEVICE_TYPE,
 		.mode_off[1] = IOMUXC_GPR12,
 		.mode_mask[1] = IMX8MQ_GPR12_PCIE2_CTRL_DEVICE_TYPE,
+		.epc_features = &imx8m_pcie_epc_features,
 		.init_phy = imx8mq_pcie_init_phy,
 	},
 	[IMX8MM_EP] = {
@@ -1540,6 +1545,7 @@ static const struct imx6_pcie_drvdata drvdata[] = {
 		.clk_names = {"pcie_bus", "pcie", "pcie_aux"},
 		.mode_off[0] = IOMUXC_GPR12,
 		.mode_mask[0] = IMX6Q_GPR12_DEVICE_TYPE,
+		.epc_features = &imx8m_pcie_epc_features,
 	},
 	[IMX8MP_EP] = {
 		.variant = IMX8MP_EP,
@@ -1549,6 +1555,7 @@ static const struct imx6_pcie_drvdata drvdata[] = {
 		.clk_names = {"pcie_bus", "pcie", "pcie_aux"},
 		.mode_off[0] = IOMUXC_GPR12,
 		.mode_mask[0] = IMX6Q_GPR12_DEVICE_TYPE,
+		.epc_features = &imx8m_pcie_epc_features,
 	},
 };
 
-- 
2.34.1

[PATCH v5 15/16] dt-bindings: imx6q-pcie: Add iMX95 pcie endpoint compatible string

[Frank Li]

Add i.MX95 PCIe "fsl,imx95-pcie-ep" compatible string.
Add reg-name: "atu", "dbi2", "dma" and "serdes".

Signed-off-by: Frank Li <Frank.Li@nxp.com>
---

Notes:
    Change from v1 to v3
    - new patches at v3

 .../bindings/pci/fsl,imx6q-pcie-ep.yaml       | 52 ++++++++++++++++---
 1 file changed, 44 insertions(+), 8 deletions(-)

diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie-ep.yaml b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie-ep.yaml
index ee155ed5f1811..be9ea77ce8548 100644
--- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie-ep.yaml
+++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie-ep.yaml
@@ -22,14 +22,7 @@ properties:
       - fsl,imx8mm-pcie-ep
       - fsl,imx8mq-pcie-ep
       - fsl,imx8mp-pcie-ep
-
-  reg:
-    minItems: 2
-
-  reg-names:
-    items:
-      - const: dbi
-      - const: addr_space
+      - fsl,imx95-pcie-ep
 
   clocks:
     minItems: 3
@@ -62,11 +55,46 @@ required:
 allOf:
   - $ref: /schemas/pci/snps,dw-pcie-ep.yaml#
   - $ref: /schemas/pci/fsl,imx6q-pcie-common.yaml#
+  - if:
+      properties:
+        compatible:
+          enum:
+            - fsl,imx8mm-pcie-ep
+            - fsl,imx8mq-pcie-ep
+            - fsl,imx8mp-pcie-ep
+    then:
+      properties:
+        reg:
+          minItems: 2
+        reg-names:
+          items:
+            - const: dbi
+            - const: addr_space
+
+  - if:
+      properties:
+        compatible:
+          enum:
+            - fsl,imx95-pcie-ep
+    then:
+      properties:
+        reg:
+          minItems: 6
+        reg-names:
+          items:
+            - const: dbi
+            - const: atu
+            - const: dbi2
+            - const: app
+            - const: dma
+            - const: addr_space
+
   - if:
       properties:
         compatible:
           enum:
             - fsl,imx8mq-pcie-ep
+            - fsl,imx95-pcie-ep
     then:
       properties:
         clocks:
@@ -87,6 +115,14 @@ allOf:
             - const: pcie_bus
             - const: pcie_aux
 
+  - if:
+      properties:
+        compatible:
+          enum:
+            - fsl,imx95-pcie-ep
+    then:
+      properties:
+        linux,pci-domain: true
 
 unevaluatedProperties: false
 
-- 
2.34.1

Re: [PATCH v5 15/16] dt-bindings: imx6q-pcie: Add iMX95 pcie endpoint compatible string

[Krzysztof Kozlowski]

On 20/12/2023 22:36, Frank Li wrote:
> Add i.MX95 PCIe "fsl,imx95-pcie-ep" compatible string.
> Add reg-name: "atu", "dbi2", "dma" and "serdes".
> 
> Signed-off-by: Frank Li <Frank.Li@nxp.com>
> ---
> 
> Notes:
>     Change from v1 to v3
>     - new patches at v3
> 
>  .../bindings/pci/fsl,imx6q-pcie-ep.yaml       | 52 ++++++++++++++++---
>  1 file changed, 44 insertions(+), 8 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie-ep.yaml b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie-ep.yaml
> index ee155ed5f1811..be9ea77ce8548 100644
> --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie-ep.yaml
> +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie-ep.yaml
> @@ -22,14 +22,7 @@ properties:
>        - fsl,imx8mm-pcie-ep
>        - fsl,imx8mq-pcie-ep
>        - fsl,imx8mp-pcie-ep
> -
> -  reg:
> -    minItems: 2
> -
> -  reg-names:
> -    items:
> -      - const: dbi
> -      - const: addr_space

No, why? Entries should be defined top-level. If you remove them here,
where are they defined (in which schema)?


> +  - if:
> +      properties:
> +        compatible:
> +          enum:
> +            - fsl,imx95-pcie-ep
> +    then:
> +      properties:
> +        linux,pci-domain: true

Why? It is allowed already.


Best regards,
Krzysztof

Re: [PATCH v5 15/16] dt-bindings: imx6q-pcie: Add iMX95 pcie endpoint compatible string

[Frank Li]

On Sat, Dec 23, 2023 at 07:44:30PM +0100, Krzysztof Kozlowski wrote:
> On 20/12/2023 22:36, Frank Li wrote:
> > Add i.MX95 PCIe "fsl,imx95-pcie-ep" compatible string.
> > Add reg-name: "atu", "dbi2", "dma" and "serdes".
> > 
> > Signed-off-by: Frank Li <Frank.Li@nxp.com>
> > ---
> > 
> > Notes:
> >     Change from v1 to v3
> >     - new patches at v3
> > 
> >  .../bindings/pci/fsl,imx6q-pcie-ep.yaml       | 52 ++++++++++++++++---
> >  1 file changed, 44 insertions(+), 8 deletions(-)
> > 
> > diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie-ep.yaml b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie-ep.yaml
> > index ee155ed5f1811..be9ea77ce8548 100644
> > --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie-ep.yaml
> > +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie-ep.yaml
> > @@ -22,14 +22,7 @@ properties:
> >        - fsl,imx8mm-pcie-ep
> >        - fsl,imx8mq-pcie-ep
> >        - fsl,imx8mp-pcie-ep
> > -
> > -  reg:
> > -    minItems: 2
> > -
> > -  reg-names:
> > -    items:
> > -      - const: dbi
> > -      - const: addr_space
> 
> No, why? Entries should be defined top-level. If you remove them here,
> where are they defined (in which schema)?

See: pci/snps,dw-pcie.yaml

> 
> 
> > +  - if:
> > +      properties:
> > +        compatible:
> > +          enum:
> > +            - fsl,imx95-pcie-ep
> > +    then:
> > +      properties:
> > +        linux,pci-domain: true
> 
> Why? It is allowed already.

Sorry, I suppose it should be required. I will fix it.

> 
> 
> Best regards,
> Krzysztof
> 

Re: [PATCH v5 15/16] dt-bindings: imx6q-pcie: Add iMX95 pcie endpoint compatible string

[Krzysztof Kozlowski]

On 24/12/2023 05:47, Frank Li wrote:
> On Sat, Dec 23, 2023 at 07:44:30PM +0100, Krzysztof Kozlowski wrote:
>> On 20/12/2023 22:36, Frank Li wrote:
>>> Add i.MX95 PCIe "fsl,imx95-pcie-ep" compatible string.
>>> Add reg-name: "atu", "dbi2", "dma" and "serdes".
>>>
>>> Signed-off-by: Frank Li <Frank.Li@nxp.com>
>>> ---
>>>
>>> Notes:
>>>     Change from v1 to v3
>>>     - new patches at v3
>>>
>>>  .../bindings/pci/fsl,imx6q-pcie-ep.yaml       | 52 ++++++++++++++++---
>>>  1 file changed, 44 insertions(+), 8 deletions(-)
>>>
>>> diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie-ep.yaml b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie-ep.yaml
>>> index ee155ed5f1811..be9ea77ce8548 100644
>>> --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie-ep.yaml
>>> +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie-ep.yaml
>>> @@ -22,14 +22,7 @@ properties:
>>>        - fsl,imx8mm-pcie-ep
>>>        - fsl,imx8mq-pcie-ep
>>>        - fsl,imx8mp-pcie-ep
>>> -
>>> -  reg:
>>> -    minItems: 2
>>> -
>>> -  reg-names:
>>> -    items:
>>> -      - const: dbi
>>> -      - const: addr_space
>>
>> No, why? Entries should be defined top-level. If you remove them here,
>> where are they defined (in which schema)?
> 
> See: pci/snps,dw-pcie.yaml

OK



Best regards,
Krzysztof

Re: [PATCH v5 15/16] dt-bindings: imx6q-pcie: Add iMX95 pcie endpoint compatible string

[Krzysztof Kozlowski]

On 20/12/2023 22:36, Frank Li wrote:
> +    then:
> +      properties:
> +        reg:
> +          minItems: 2

Missing maxItems.

> +        reg-names:
> +          items:
> +            - const: dbi
> +            - const: addr_space
> +
> +  - if:
> +      properties:
> +        compatible:
> +          enum:
> +            - fsl,imx95-pcie-ep
> +    then:
> +      properties:
> +        reg:
> +          minItems: 6

Missing maxItems.



Best regards,
Krzysztof

[PATCH v5 16/16] PCI: imx6: Add iMX95 Endpoint (EP) function support

[Frank Li]

Add iMX95 EP function support and add 64bit address support. Internal bus
bridge for PCI support 64bit dma address in iMX95. So set call
dma_set_mask_and_coherent(dev, DMA_BIT_MASK(64)).

Signed-off-by: Frank Li <Frank.Li@nxp.com>
---

Notes:
    Change from v3 to v4
    - change align to 4k for imx95
    Change from v1 to v3
    - new patches at v3

 drivers/pci/controller/dwc/pci-imx6.c | 45 +++++++++++++++++++++++++++
 1 file changed, 45 insertions(+)

diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c
index 6a58fd63a9dd2..00ec59867c17b 100644
--- a/drivers/pci/controller/dwc/pci-imx6.c
+++ b/drivers/pci/controller/dwc/pci-imx6.c
@@ -75,6 +75,7 @@ enum imx6_pcie_variants {
 	IMX8MQ_EP,
 	IMX8MM_EP,
 	IMX8MP_EP,
+	IMX95_EP,
 };
 
 #define IMX6_PCIE_FLAG_IMX6_PHY			BIT(0)
@@ -84,6 +85,7 @@ enum imx6_pcie_variants {
 #define IMX6_PCIE_FLAG_HAS_APP_RESET		BIT(4)
 #define IMX6_PCIE_FLAG_HAS_PHY_RESET		BIT(5)
 #define IMX6_PCIE_FLAG_HAS_SERDES		BIT(6)
+#define IMX6_PCIE_FLAG_SUPPORT_64BIT		BIT(7)
 
 #define imx6_check_flag(pci, val)     (pci->drvdata->flags & val)
 
@@ -620,6 +622,7 @@ static int imx6_pcie_enable_ref_clk(struct imx6_pcie *imx6_pcie)
 		break;
 	case IMX7D:
 	case IMX95:
+	case IMX95_EP:
 		break;
 	case IMX8MM:
 	case IMX8MM_EP:
@@ -1063,6 +1066,23 @@ static const struct pci_epc_features imx8m_pcie_epc_features = {
 	.align = SZ_64K,
 };
 
+/*
+ * BAR#	| Default BAR enable	| Default BAR Type	| Default BAR Size	| BAR Sizing Scheme
+ * ================================================================================================
+ * BAR0	| Enable		| 64-bit		| 1 MB			| Programmable Size
+ * BAR1	| Disable		| 32-bit		| 64 KB			| Fixed Size
+ *	| (BAR0 is 64-bit)	| if BAR0 is 32-bit	|			| As Bar0 is 64bit
+ * BAR2	| Enable		| 32-bit		| 1 MB			| Programmable Size
+ * BAR3	| Enable		| 32-bit		| 64 KB			| Programmable Size
+ * BAR4	| Enable		| 32-bit		| 1M			| Programmable Size
+ * BAR5	| Enable		| 32-bit		| 64 KB			| Programmable Size
+ */
+static const struct pci_epc_features imx95_pcie_epc_features = {
+	.msi_capable = true,
+	.bar_fixed_size[1] = SZ_64K,
+	.align = SZ_4K,
+};
+
 static const struct pci_epc_features*
 imx6_pcie_ep_get_features(struct dw_pcie_ep *ep)
 {
@@ -1105,6 +1125,14 @@ static int imx6_add_pcie_ep(struct imx6_pcie *imx6_pcie,
 
 	pci->dbi_base2 = pci->dbi_base + pcie_dbi2_offset;
 
+	/*
+	 * db2 information should fetch from dtb file. dw_pcie_ep_init() can get dbi_base2 from
+	 * "dbi2" if pci->dbi_base2 is NULL. All code related pcie_dbi2_offset should be removed
+	 * after all dts added "dbi2" reg.
+	 */
+	if (imx6_pcie->drvdata->variant == IMX95_EP)
+		pci->dbi_base2 = NULL;
+
 	ret = dw_pcie_ep_init(ep);
 	if (ret) {
 		dev_err(dev, "failed to initialize endpoint\n");
@@ -1355,6 +1383,9 @@ static int imx6_pcie_probe(struct platform_device *pdev)
 					     "unable to find iomuxc registers\n");
 	}
 
+	if (imx6_check_flag(imx6_pcie, IMX6_PCIE_FLAG_SUPPORT_64BIT))
+		dma_set_mask_and_coherent(dev, DMA_BIT_MASK(64));
+
 	/* Grab PCIe PHY Tx Settings */
 	if (of_property_read_u32(node, "fsl,tx-deemph-gen1",
 				 &imx6_pcie->tx_deemph_gen1))
@@ -1557,6 +1588,19 @@ static const struct imx6_pcie_drvdata drvdata[] = {
 		.mode_mask[0] = IMX6Q_GPR12_DEVICE_TYPE,
 		.epc_features = &imx8m_pcie_epc_features,
 	},
+	[IMX95_EP] = {
+		.variant = IMX95_EP,
+		.flags = IMX6_PCIE_FLAG_HAS_SERDES |
+			 IMX6_PCIE_FLAG_SUPPORT_64BIT,
+		.clk_names = {"pcie_bus", "pcie", "pcie_phy", "pcie_aux"},
+		.ltssm_off = IMX95_PE0_GEN_CTRL_3,
+		.ltssm_mask = IMX95_PCIE_LTSSM_EN,
+		.mode_off[0]  = IMX95_PE0_GEN_CTRL_1,
+		.mode_mask[0] = IMX95_PCIE_DEVICE_TYPE,
+		.init_phy = imx95_pcie_init_phy,
+		.epc_features = &imx95_pcie_epc_features,
+		.mode = DW_PCIE_EP_TYPE,
+	},
 };
 
 static const struct of_device_id imx6_pcie_of_match[] = {
@@ -1571,6 +1615,7 @@ static const struct of_device_id imx6_pcie_of_match[] = {
 	{ .compatible = "fsl,imx8mq-pcie-ep", .data = &drvdata[IMX8MQ_EP], },
 	{ .compatible = "fsl,imx8mm-pcie-ep", .data = &drvdata[IMX8MM_EP], },
 	{ .compatible = "fsl,imx8mp-pcie-ep", .data = &drvdata[IMX8MP_EP], },
+	{ .compatible = "fsl,imx95-pcie-ep", .data = &drvdata[IMX95_EP], },
 	{},
 };
 
-- 
2.34.1