* [PATCH v3] arm64: dts: qcom: x1e80100: Enable tsens and thermal zone nodes
@ 2024-06-21 7:20 Abel Vesa
2024-06-22 11:29 ` Konrad Dybcio
2024-06-23 21:02 ` Bjorn Andersson
0 siblings, 2 replies; 3+ messages in thread
From: Abel Vesa @ 2024-06-21 7:20 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: Johan Hovold, Dmitry Baryshkov, linux-arm-msm, devicetree,
linux-kernel, Rajendra Nayak, Abel Vesa
From: Rajendra Nayak <quic_rjendra@quicinc.com>
Add tsens and thermal zones nodes for x1e80100 SoC.
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
Changes in v3:
- Changed the upper-lower tsense interrupts to PDC.
- Renamed the 'bottom' thermal zones to 'btm' due to name lenght
limitation in thermal framework.
- Dropped the passive polling delay from zones where there are no
passsive trip points.
- Link to v2: https://lore.kernel.org/r/20240614-x1e80100-dts-thermal-v2-1-4d4f9effacc6@linaro.org
Changes in v2:
- Dropped the thermal engine nodes.
- Dropped comments from tsens nodes.
- Droppd the polling-delay entirely and polling-delay-passive where not
necessary.
- Added top/bottom location to all sensors (where applicable).
- Fixed trip points with duplicate values for same temp.
- Marked as critical the 125°C throughout all trip points.
- Link to v1: https://lore.kernel.org/r/20240527-x1e80100-dts-thermal-v1-1-ea13b8fa6ffc@linaro.org
---
arch/arm64/boot/dts/qcom/x1e80100.dtsi | 1214 ++++++++++++++++++++++++++++++++
1 file changed, 1214 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
index 9944c654851e..09fd6c8e53bb 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
+++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
@@ -2505,6 +2505,66 @@ &config_noc SLAVE_QUP_0 QCOM_ICC_TAG_ALWAYS>,
};
};
+ tsens0: thermal-sensor@c271000 {
+ compatible = "qcom,x1e80100-tsens", "qcom,tsens-v2";
+ reg = <0 0x0c271000 0 0x1000>,
+ <0 0x0c222000 0 0x1000>;
+
+ interrupts-extended = <&pdc 26 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 641 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "uplow",
+ "critical";
+
+ #qcom,sensors = <16>;
+
+ #thermal-sensor-cells = <1>;
+ };
+
+ tsens1: thermal-sensor@c272000 {
+ compatible = "qcom,x1e80100-tsens", "qcom,tsens-v2";
+ reg = <0 0x0c272000 0 0x1000>,
+ <0 0x0c223000 0 0x1000>;
+
+ interrupts-extended = <&pdc 27 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 642 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "uplow",
+ "critical";
+
+ #qcom,sensors = <16>;
+
+ #thermal-sensor-cells = <1>;
+ };
+
+ tsens2: thermal-sensor@c273000 {
+ compatible = "qcom,x1e80100-tsens", "qcom,tsens-v2";
+ reg = <0 0x0c273000 0 0x1000>,
+ <0 0x0c224000 0 0x1000>;
+
+ interrupts-extended = <&pdc 28 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 643 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "uplow",
+ "critical";
+
+ #qcom,sensors = <16>;
+
+ #thermal-sensor-cells = <1>;
+ };
+
+ tsens3: thermal-sensor@c274000 {
+ compatible = "qcom,x1e80100-tsens", "qcom,tsens-v2";
+ reg = <0 0x0c274000 0 0x1000>,
+ <0 0x0c225000 0 0x1000>;
+
+ interrupts-extended = <&pdc 29 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 770 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "uplow",
+ "critical";
+
+ #qcom,sensors = <16>;
+
+ #thermal-sensor-cells = <1>;
+ };
+
usb_1_ss0_hsphy: phy@fd3000 {
compatible = "qcom,x1e80100-snps-eusb2-phy",
"qcom,sm8550-snps-eusb2-phy";
@@ -5469,4 +5529,1158 @@ timer {
<GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
<GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
};
+
+ thermal-zones {
+ aoss0-thermal {
+ thermal-sensors = <&tsens0 0>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+
+ aoss0-critical {
+ temperature = <125000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu0-0-top-thermal {
+ polling-delay-passive = <250>;
+
+ thermal-sensors = <&tsens0 1>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu-critical {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu0-0-btm-thermal {
+ polling-delay-passive = <250>;
+
+ thermal-sensors = <&tsens0 2>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu-critical {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu0-1-top-thermal {
+ polling-delay-passive = <250>;
+
+ thermal-sensors = <&tsens0 3>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu-critical {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu0-1-btm-thermal {
+ polling-delay-passive = <250>;
+
+ thermal-sensors = <&tsens0 4>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu-critical {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu0-2-top-thermal {
+ polling-delay-passive = <250>;
+
+ thermal-sensors = <&tsens0 5>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu-critical {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu0-2-btm-thermal {
+ polling-delay-passive = <250>;
+
+ thermal-sensors = <&tsens0 6>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu-critical {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu0-3-top-thermal {
+ polling-delay-passive = <250>;
+
+ thermal-sensors = <&tsens0 7>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu-critical {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu0-3-btm-thermal {
+ polling-delay-passive = <250>;
+
+ thermal-sensors = <&tsens0 8>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu-critical {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpuss0-top-thermal {
+ thermal-sensors = <&tsens0 9>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+
+ cpuss2-critical {
+ temperature = <125000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpuss0-btm-thermal {
+ thermal-sensors = <&tsens0 10>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+
+ cpuss2-critical {
+ temperature = <125000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+ };
+
+ mem-thermal {
+ thermal-sensors = <&tsens0 11>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+
+ mem-critical {
+ temperature = <125000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+ };
+
+ video-thermal {
+ polling-delay-passive = <250>;
+
+ thermal-sensors = <&tsens0 12>;
+
+ trips {
+ trip-point0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ aoss1-thermal {
+ thermal-sensors = <&tsens1 0>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+
+ aoss0-critical {
+ temperature = <125000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu1-0-top-thermal {
+ polling-delay-passive = <250>;
+
+ thermal-sensors = <&tsens1 1>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu-critical {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu1-0-btm-thermal {
+ polling-delay-passive = <250>;
+
+ thermal-sensors = <&tsens1 2>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu-critical {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu1-1-top-thermal {
+ polling-delay-passive = <250>;
+
+ thermal-sensors = <&tsens1 3>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu-critical {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu1-1-btm-thermal {
+ polling-delay-passive = <250>;
+
+ thermal-sensors = <&tsens1 4>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu-critical {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu1-2-top-thermal {
+ polling-delay-passive = <250>;
+
+ thermal-sensors = <&tsens1 5>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu-critical {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu1-2-btm-thermal {
+ polling-delay-passive = <250>;
+
+ thermal-sensors = <&tsens1 6>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu-critical {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu1-3-top-thermal {
+ polling-delay-passive = <250>;
+
+ thermal-sensors = <&tsens1 7>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu-critical {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu1-3-btm-thermal {
+ polling-delay-passive = <250>;
+
+ thermal-sensors = <&tsens1 8>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu-critical {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpuss1-top-thermal {
+ thermal-sensors = <&tsens1 9>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+
+ cpuss2-critical {
+ temperature = <125000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpuss1-btm-thermal {
+ thermal-sensors = <&tsens1 10>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+
+ cpuss2-critical {
+ temperature = <125000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+ };
+
+ aoss2-thermal {
+ thermal-sensors = <&tsens2 0>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+
+ aoss0-critical {
+ temperature = <125000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu2-0-top-thermal {
+ polling-delay-passive = <250>;
+
+ thermal-sensors = <&tsens2 1>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu-critical {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu2-0-btm-thermal {
+ polling-delay-passive = <250>;
+
+ thermal-sensors = <&tsens2 2>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu-critical {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu2-1-top-thermal {
+ polling-delay-passive = <250>;
+
+ thermal-sensors = <&tsens2 3>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu-critical {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu2-1-btm-thermal {
+ polling-delay-passive = <250>;
+
+ thermal-sensors = <&tsens2 4>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu-critical {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu2-2-top-thermal {
+ polling-delay-passive = <250>;
+
+ thermal-sensors = <&tsens2 5>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu-critical {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu2-2-btm-thermal {
+ polling-delay-passive = <250>;
+
+ thermal-sensors = <&tsens2 6>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu-critical {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu2-3-top-thermal {
+ polling-delay-passive = <250>;
+
+ thermal-sensors = <&tsens2 7>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu-critical {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu2-3-btm-thermal {
+ polling-delay-passive = <250>;
+
+ thermal-sensors = <&tsens2 8>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu-critical {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpuss2-top-thermal {
+ thermal-sensors = <&tsens2 9>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+
+ cpuss2-critical {
+ temperature = <125000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpuss2-btm-thermal {
+ thermal-sensors = <&tsens2 10>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+
+ cpuss2-critical {
+ temperature = <125000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+ };
+
+ aoss3-thermal {
+ thermal-sensors = <&tsens3 0>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+
+ aoss0-critical {
+ temperature = <125000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+ };
+
+ nsp0-thermal {
+ thermal-sensors = <&tsens3 1>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+
+ nsp0-critical {
+ temperature = <125000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+ };
+
+ nsp1-thermal {
+ thermal-sensors = <&tsens3 2>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+
+ nsp1-critical {
+ temperature = <125000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+ };
+
+ nsp2-thermal {
+ thermal-sensors = <&tsens3 3>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+
+ nsp2-critical {
+ temperature = <125000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+ };
+
+ nsp3-thermal {
+ thermal-sensors = <&tsens3 4>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+
+ nsp3-critical {
+ temperature = <125000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+ };
+
+ gpuss-0-thermal {
+ polling-delay-passive = <10>;
+
+ thermal-sensors = <&tsens3 5>;
+
+ trips {
+ trip-point0 {
+ temperature = <85000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+
+ trip-point1 {
+ temperature = <90000>;
+ hysteresis = <1000>;
+ type = "hot";
+ };
+
+ trip-point2 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ gpuss-1-thermal {
+ polling-delay-passive = <10>;
+
+ thermal-sensors = <&tsens3 6>;
+
+ trips {
+ trip-point0 {
+ temperature = <85000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+
+ trip-point1 {
+ temperature = <90000>;
+ hysteresis = <1000>;
+ type = "hot";
+ };
+
+ trip-point2 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ gpuss-2-thermal {
+ polling-delay-passive = <10>;
+
+ thermal-sensors = <&tsens3 7>;
+
+ trips {
+ trip-point0 {
+ temperature = <85000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+
+ trip-point1 {
+ temperature = <90000>;
+ hysteresis = <1000>;
+ type = "hot";
+ };
+
+ trip-point2 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ gpuss-3-thermal {
+ polling-delay-passive = <10>;
+
+ thermal-sensors = <&tsens3 8>;
+
+ trips {
+ trip-point0 {
+ temperature = <85000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+
+ trip-point1 {
+ temperature = <90000>;
+ hysteresis = <1000>;
+ type = "hot";
+ };
+
+ trip-point2 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ gpuss-4-thermal {
+ polling-delay-passive = <10>;
+
+ thermal-sensors = <&tsens3 9>;
+
+ trips {
+ trip-point0 {
+ temperature = <85000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+
+ trip-point1 {
+ temperature = <90000>;
+ hysteresis = <1000>;
+ type = "hot";
+ };
+
+ trip-point2 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ gpuss-5-thermal {
+ polling-delay-passive = <10>;
+
+ thermal-sensors = <&tsens3 10>;
+
+ trips {
+ trip-point0 {
+ temperature = <85000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+
+ trip-point1 {
+ temperature = <90000>;
+ hysteresis = <1000>;
+ type = "hot";
+ };
+
+ trip-point2 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ gpuss-6-thermal {
+ polling-delay-passive = <10>;
+
+ thermal-sensors = <&tsens3 11>;
+
+ trips {
+ trip-point0 {
+ temperature = <85000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+
+ trip-point1 {
+ temperature = <90000>;
+ hysteresis = <1000>;
+ type = "hot";
+ };
+
+ trip-point2 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ gpuss-7-thermal {
+ polling-delay-passive = <10>;
+
+ thermal-sensors = <&tsens3 12>;
+
+ trips {
+ trip-point0 {
+ temperature = <85000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+
+ trip-point1 {
+ temperature = <90000>;
+ hysteresis = <1000>;
+ type = "hot";
+ };
+
+ trip-point2 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ camera0-thermal {
+ thermal-sensors = <&tsens3 13>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+
+ camera0-critical {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+ };
+
+ camera1-thermal {
+ thermal-sensors = <&tsens3 14>;
+
+ trips {
+ trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+
+ camera0-critical {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+ };
+ };
};
---
base-commit: 2102cb0d050d34d50b9642a3a50861787527e922
change-id: 20240109-x1e80100-dts-thermal-47db566a60bc
Best regards,
--
Abel Vesa <abel.vesa@linaro.org>
^ permalink raw reply related [flat|nested] 3+ messages in thread* Re: [PATCH v3] arm64: dts: qcom: x1e80100: Enable tsens and thermal zone nodes
2024-06-21 7:20 [PATCH v3] arm64: dts: qcom: x1e80100: Enable tsens and thermal zone nodes Abel Vesa
@ 2024-06-22 11:29 ` Konrad Dybcio
2024-06-23 21:02 ` Bjorn Andersson
1 sibling, 0 replies; 3+ messages in thread
From: Konrad Dybcio @ 2024-06-22 11:29 UTC (permalink / raw)
To: Abel Vesa, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: Johan Hovold, Dmitry Baryshkov, linux-arm-msm, devicetree,
linux-kernel, Rajendra Nayak
On 21.06.2024 9:20 AM, Abel Vesa wrote:
> From: Rajendra Nayak <quic_rjendra@quicinc.com>
>
> Add tsens and thermal zones nodes for x1e80100 SoC.
>
> Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---
> Changes in v3:
> - Changed the upper-lower tsense interrupts to PDC.
I'm still puzzled that the critical irq is not wired up through pdc as
you've said, since it would make a lot of sense that if the thermal subsystem
detects a dangerous situation, the AP would be woken up and the soc would be
then shut down by the OS before any last-moment safety mechanisms (if such
exist) kick in..
Anyway, this looks good now to my brain compiler and the device seems to agree
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Tested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Konrad
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [PATCH v3] arm64: dts: qcom: x1e80100: Enable tsens and thermal zone nodes
2024-06-21 7:20 [PATCH v3] arm64: dts: qcom: x1e80100: Enable tsens and thermal zone nodes Abel Vesa
2024-06-22 11:29 ` Konrad Dybcio
@ 2024-06-23 21:02 ` Bjorn Andersson
1 sibling, 0 replies; 3+ messages in thread
From: Bjorn Andersson @ 2024-06-23 21:02 UTC (permalink / raw)
To: Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Abel Vesa
Cc: Johan Hovold, Dmitry Baryshkov, linux-arm-msm, devicetree,
linux-kernel, Rajendra Nayak
On Fri, 21 Jun 2024 10:20:06 +0300, Abel Vesa wrote:
> Add tsens and thermal zones nodes for x1e80100 SoC.
>
>
Applied, thanks!
[1/1] arm64: dts: qcom: x1e80100: Enable tsens and thermal zone nodes
commit: 4e915987ff5b91ea531e716367373ff4442d9614
Best regards,
--
Bjorn Andersson <andersson@kernel.org>
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2024-06-23 21:02 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2024-06-21 7:20 [PATCH v3] arm64: dts: qcom: x1e80100: Enable tsens and thermal zone nodes Abel Vesa
2024-06-22 11:29 ` Konrad Dybcio
2024-06-23 21:02 ` Bjorn Andersson
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).