[PATCH v2 0/3] arm64: dts: qcom: sa8775p-ride: support both board variants

[PATCH v2 0/3] arm64: dts: qcom: sa8775p-ride: support both board variants

[Bartosz Golaszewski]

From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

Split the current .dts into two: the existing one keeps the name and
supports revision 2 of the board while patch 2 adds a .dts for revision 3.

Changes since v1:
- add a new compatible for Rev3

Bartosz Golaszewski (3):
  dt-bindings: arm: qcom: add sa8775p-ride Rev 3
  arm64: dts: qcom: move common parts for sa8775p-ride variants into a
    .dtsi
  arm64: dts: qcom: sa8775p-ride-r3: add new board file

 .../devicetree/bindings/arm/qcom.yaml         |   1 +
 arch/arm64/boot/dts/qcom/Makefile             |   1 +
 arch/arm64/boot/dts/qcom/sa8775p-ride-r3.dts  |  47 +
 arch/arm64/boot/dts/qcom/sa8775p-ride.dts     | 836 +-----------------
 arch/arm64/boot/dts/qcom/sa8775p-ride.dtsi    | 814 +++++++++++++++++
 5 files changed, 885 insertions(+), 814 deletions(-)
 create mode 100644 arch/arm64/boot/dts/qcom/sa8775p-ride-r3.dts
 create mode 100644 arch/arm64/boot/dts/qcom/sa8775p-ride.dtsi

-- 
2.43.0

[PATCH v2 1/3] dt-bindings: arm: qcom: add sa8775p-ride Rev 3

[Bartosz Golaszewski]

From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

Document the compatible for revision 3 of the sa8775p-ride board.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
---
 Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index ec1c10a12470..000037f4a712 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -895,6 +895,7 @@ properties:
       - items:
           - enum:
               - qcom,sa8775p-ride
+              - qcom,sa8775p-ride-r3
           - const: qcom,sa8775p
 
       - items:
-- 
2.43.0

[PATCH v2 2/3] arm64: dts: qcom: move common parts for sa8775p-ride variants into a .dtsi

[Bartosz Golaszewski]

From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

In order to support multiple revisions of the sa8775p-ride board, create
a .dtsi containing the common parts and split out the ethernet bits into
the actual board file as they will change in revision 3.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
---
 arch/arm64/boot/dts/qcom/sa8775p-ride.dts  | 836 +--------------------
 arch/arm64/boot/dts/qcom/sa8775p-ride.dtsi | 814 ++++++++++++++++++++
 2 files changed, 836 insertions(+), 814 deletions(-)
 create mode 100644 arch/arm64/boot/dts/qcom/sa8775p-ride.dtsi

diff --git a/arch/arm64/boot/dts/qcom/sa8775p-ride.dts b/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
index 26ad05bd3b3f..2e87fd760dbd 100644
--- a/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
+++ b/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
@@ -5,835 +5,43 @@
 
 /dts-v1/;
 
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
-
-#include "sa8775p.dtsi"
-#include "sa8775p-pmics.dtsi"
+#include "sa8775p-ride.dtsi"
 
 / {
 	model = "Qualcomm SA8775P Ride";
 	compatible = "qcom,sa8775p-ride", "qcom,sa8775p";
-
-	aliases {
-		ethernet0 = &ethernet0;
-		ethernet1 = &ethernet1;
-		i2c11 = &i2c11;
-		i2c18 = &i2c18;
-		serial0 = &uart10;
-		serial1 = &uart12;
-		serial2 = &uart17;
-		spi16 = &spi16;
-		ufshc1 = &ufs_mem_hc;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-};
-
-&apps_rsc {
-	regulators-0 {
-		compatible = "qcom,pmm8654au-rpmh-regulators";
-		qcom,pmic-id = "a";
-
-		vreg_s4a: smps4 {
-			regulator-name = "vreg_s4a";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1816000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_s5a: smps5 {
-			regulator-name = "vreg_s5a";
-			regulator-min-microvolt = <1850000>;
-			regulator-max-microvolt = <1996000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_s9a: smps9 {
-			regulator-name = "vreg_s9a";
-			regulator-min-microvolt = <535000>;
-			regulator-max-microvolt = <1120000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l4a: ldo4 {
-			regulator-name = "vreg_l4a";
-			regulator-min-microvolt = <788000>;
-			regulator-max-microvolt = <1050000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l5a: ldo5 {
-			regulator-name = "vreg_l5a";
-			regulator-min-microvolt = <870000>;
-			regulator-max-microvolt = <950000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l6a: ldo6 {
-			regulator-name = "vreg_l6a";
-			regulator-min-microvolt = <870000>;
-			regulator-max-microvolt = <970000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l7a: ldo7 {
-			regulator-name = "vreg_l7a";
-			regulator-min-microvolt = <720000>;
-			regulator-max-microvolt = <950000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l8a: ldo8 {
-			regulator-name = "vreg_l8a";
-			regulator-min-microvolt = <2504000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l9a: ldo9 {
-			regulator-name = "vreg_l9a";
-			regulator-min-microvolt = <2970000>;
-			regulator-max-microvolt = <3544000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-	};
-
-	regulators-1 {
-		compatible = "qcom,pmm8654au-rpmh-regulators";
-		qcom,pmic-id = "c";
-
-		vreg_l1c: ldo1 {
-			regulator-name = "vreg_l1c";
-			regulator-min-microvolt = <1140000>;
-			regulator-max-microvolt = <1260000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l2c: ldo2 {
-			regulator-name = "vreg_l2c";
-			regulator-min-microvolt = <900000>;
-			regulator-max-microvolt = <1100000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l3c: ldo3 {
-			regulator-name = "vreg_l3c";
-			regulator-min-microvolt = <1100000>;
-			regulator-max-microvolt = <1300000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l4c: ldo4 {
-			regulator-name = "vreg_l4c";
-			regulator-min-microvolt = <1200000>;
-			regulator-max-microvolt = <1200000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			/*
-			 * FIXME: This should have regulator-allow-set-load but
-			 * we're getting an over-current fault from the PMIC
-			 * when switching to LPM.
-			 */
-		};
-
-		vreg_l5c: ldo5 {
-			regulator-name = "vreg_l5c";
-			regulator-min-microvolt = <1100000>;
-			regulator-max-microvolt = <1300000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l6c: ldo6 {
-			regulator-name = "vreg_l6c";
-			regulator-min-microvolt = <1620000>;
-			regulator-max-microvolt = <1980000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l7c: ldo7 {
-			regulator-name = "vreg_l7c";
-			regulator-min-microvolt = <1620000>;
-			regulator-max-microvolt = <2000000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l8c: ldo8 {
-			regulator-name = "vreg_l8c";
-			regulator-min-microvolt = <2400000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l9c: ldo9 {
-			regulator-name = "vreg_l9c";
-			regulator-min-microvolt = <1650000>;
-			regulator-max-microvolt = <2700000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-	};
-
-	regulators-2 {
-		compatible = "qcom,pmm8654au-rpmh-regulators";
-		qcom,pmic-id = "e";
-
-		vreg_s4e: smps4 {
-			regulator-name = "vreg_s4e";
-			regulator-min-microvolt = <970000>;
-			regulator-max-microvolt = <1520000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_s7e: smps7 {
-			regulator-name = "vreg_s7e";
-			regulator-min-microvolt = <1010000>;
-			regulator-max-microvolt = <1170000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_s9e: smps9 {
-			regulator-name = "vreg_s9e";
-			regulator-min-microvolt = <300000>;
-			regulator-max-microvolt = <570000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l6e: ldo6 {
-			regulator-name = "vreg_l6e";
-			regulator-min-microvolt = <1280000>;
-			regulator-max-microvolt = <1450000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l8e: ldo8 {
-			regulator-name = "vreg_l8e";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1950000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-	};
 };
 
 &ethernet0 {
 	phy-mode = "sgmii";
-	phy-handle = <&sgmii_phy0>;
-
-	pinctrl-0 = <&ethernet0_default>;
-	pinctrl-names = "default";
-
-	snps,mtl-rx-config = <&mtl_rx_setup>;
-	snps,mtl-tx-config = <&mtl_tx_setup>;
-	snps,ps-speed = <1000>;
-
-	status = "okay";
-
-	mdio {
-		compatible = "snps,dwmac-mdio";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		sgmii_phy0: phy@8 {
-			compatible = "ethernet-phy-id0141.0dd4";
-			reg = <0x8>;
-			device_type = "ethernet-phy";
-			interrupts-extended = <&tlmm 7 IRQ_TYPE_EDGE_FALLING>;
-			reset-gpios = <&pmm8654au_2_gpios 8 GPIO_ACTIVE_LOW>;
-			reset-assert-us = <11000>;
-			reset-deassert-us = <70000>;
-		};
-
-		sgmii_phy1: phy@a {
-			compatible = "ethernet-phy-id0141.0dd4";
-			reg = <0xa>;
-			device_type = "ethernet-phy";
-			interrupts-extended = <&tlmm 26 IRQ_TYPE_EDGE_FALLING>;
-			reset-gpios = <&pmm8654au_2_gpios 9 GPIO_ACTIVE_LOW>;
-			reset-assert-us = <11000>;
-			reset-deassert-us = <70000>;
-		};
-	};
-
-	mtl_rx_setup: rx-queues-config {
-		snps,rx-queues-to-use = <4>;
-		snps,rx-sched-sp;
-
-		queue0 {
-			snps,dcb-algorithm;
-			snps,map-to-dma-channel = <0x0>;
-			snps,route-up;
-			snps,priority = <0x1>;
-		};
-
-		queue1 {
-			snps,dcb-algorithm;
-			snps,map-to-dma-channel = <0x1>;
-			snps,route-ptp;
-		};
-
-		queue2 {
-			snps,avb-algorithm;
-			snps,map-to-dma-channel = <0x2>;
-			snps,route-avcp;
-		};
-
-		queue3 {
-			snps,avb-algorithm;
-			snps,map-to-dma-channel = <0x3>;
-			snps,priority = <0xc>;
-		};
-	};
-
-	mtl_tx_setup: tx-queues-config {
-		snps,tx-queues-to-use = <4>;
-		snps,tx-sched-sp;
-
-		queue0 {
-			snps,dcb-algorithm;
-		};
-
-		queue1 {
-			snps,dcb-algorithm;
-		};
-
-		queue2 {
-			snps,avb-algorithm;
-			snps,send_slope = <0x1000>;
-			snps,idle_slope = <0x1000>;
-			snps,high_credit = <0x3e800>;
-			snps,low_credit = <0xffc18000>;
-		};
-
-		queue3 {
-			snps,avb-algorithm;
-			snps,send_slope = <0x1000>;
-			snps,idle_slope = <0x1000>;
-			snps,high_credit = <0x3e800>;
-			snps,low_credit = <0xffc18000>;
-		};
-	};
 };
 
 &ethernet1 {
 	phy-mode = "sgmii";
-	phy-handle = <&sgmii_phy1>;
+};
 
-	snps,mtl-rx-config = <&mtl_rx_setup1>;
-	snps,mtl-tx-config = <&mtl_tx_setup1>;
-	snps,ps-speed = <1000>;
+&mdio {
+	compatible = "snps,dwmac-mdio";
+	#address-cells = <1>;
+	#size-cells = <0>;
 
-	status = "okay";
-
-	mtl_rx_setup1: rx-queues-config {
-		snps,rx-queues-to-use = <4>;
-		snps,rx-sched-sp;
-
-		queue0 {
-			snps,dcb-algorithm;
-			snps,map-to-dma-channel = <0x0>;
-			snps,route-up;
-			snps,priority = <0x1>;
-		};
-
-		queue1 {
-			snps,dcb-algorithm;
-			snps,map-to-dma-channel = <0x1>;
-			snps,route-ptp;
-		};
-
-		queue2 {
-			snps,avb-algorithm;
-			snps,map-to-dma-channel = <0x2>;
-			snps,route-avcp;
-		};
-
-		queue3 {
-			snps,avb-algorithm;
-			snps,map-to-dma-channel = <0x3>;
-			snps,priority = <0xc>;
-		};
+	sgmii_phy0: phy@8 {
+		compatible = "ethernet-phy-id0141.0dd4";
+		reg = <0x8>;
+		device_type = "ethernet-phy";
+		interrupts-extended = <&tlmm 7 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&pmm8654au_2_gpios 8 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <11000>;
+		reset-deassert-us = <70000>;
 	};
 
-	mtl_tx_setup1: tx-queues-config {
-		snps,tx-queues-to-use = <4>;
-		snps,tx-sched-sp;
-
-		queue0 {
-			snps,dcb-algorithm;
-		};
-
-		queue1 {
-			snps,dcb-algorithm;
-		};
-
-		queue2 {
-			snps,avb-algorithm;
-			snps,send_slope = <0x1000>;
-			snps,idle_slope = <0x1000>;
-			snps,high_credit = <0x3e800>;
-			snps,low_credit = <0xffc18000>;
-		};
-
-		queue3 {
-			snps,avb-algorithm;
-			snps,send_slope = <0x1000>;
-			snps,idle_slope = <0x1000>;
-			snps,high_credit = <0x3e800>;
-			snps,low_credit = <0xffc18000>;
-		};
+	sgmii_phy1: phy@a {
+		compatible = "ethernet-phy-id0141.0dd4";
+		reg = <0xa>;
+		device_type = "ethernet-phy";
+		interrupts-extended = <&tlmm 26 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&pmm8654au_2_gpios 9 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <11000>;
+		reset-deassert-us = <70000>;
 	};
 };
-
-&i2c11 {
-	clock-frequency = <400000>;
-	pinctrl-0 = <&qup_i2c11_default>;
-	pinctrl-names = "default";
-	status = "okay";
-};
-
-&i2c18 {
-	clock-frequency = <400000>;
-	pinctrl-0 = <&qup_i2c18_default>;
-	pinctrl-names = "default";
-	status = "okay";
-};
-
-&pmm8654au_0_gpios {
-	gpio-line-names = "DS_EN",
-			  "POFF_COMPLETE",
-			  "UFS0_VER_ID",
-			  "FAST_POFF",
-			  "DBU1_PON_DONE",
-			  "AOSS_SLEEP",
-			  "CAM_DES0_EN",
-			  "CAM_DES1_EN",
-			  "CAM_DES2_EN",
-			  "CAM_DES3_EN",
-			  "UEFI",
-			  "ANALOG_PON_OPT";
-};
-
-&pmm8654au_0_pon_resin {
-	linux,code = <KEY_VOLUMEDOWN>;
-	status = "okay";
-};
-
-&pmm8654au_1_gpios {
-	gpio-line-names = "PMIC_C_ID0",
-			  "PMIC_C_ID1",
-			  "UFS1_VER_ID",
-			  "IPA_PWR",
-			  "",
-			  "WLAN_DBU4_EN",
-			  "WLAN_EN",
-			  "BT_EN",
-			  "USB2_PWR_EN",
-			  "USB2_FAULT";
-
-	usb2_en_state: usb2-en-state {
-		pins = "gpio9";
-		function = "normal";
-		output-high;
-		power-source = <0>;
-	};
-};
-
-&pmm8654au_2_gpios {
-	gpio-line-names = "PMIC_E_ID0",
-			  "PMIC_E_ID1",
-			  "USB0_PWR_EN",
-			  "USB0_FAULT",
-			  "SENSOR_IRQ_1",
-			  "SENSOR_IRQ_2",
-			  "SENSOR_RST",
-			  "SGMIIO0_RST",
-			  "SGMIIO1_RST",
-			  "USB1_PWR_ENABLE",
-			  "USB1_FAULT",
-			  "VMON_SPX8";
-
-	usb0_en_state: usb0-en-state {
-		pins = "gpio3";
-		function = "normal";
-		output-high;
-		power-source = <0>;
-	};
-
-	usb1_en_state: usb1-en-state {
-		pins = "gpio10";
-		function = "normal";
-		output-high;
-		power-source = <0>;
-	};
-};
-
-&pmm8654au_3_gpios {
-	gpio-line-names = "PMIC_G_ID0",
-			  "PMIC_G_ID1",
-			  "GNSS_RST",
-			  "GNSS_EN",
-			  "GNSS_BOOT_MODE";
-};
-
-&qupv3_id_1 {
-	status = "okay";
-};
-
-&qupv3_id_2 {
-	status = "okay";
-};
-
-&serdes0 {
-	phy-supply = <&vreg_l5a>;
-	status = "okay";
-};
-
-&serdes1 {
-	phy-supply = <&vreg_l5a>;
-	status = "okay";
-};
-
-&sleep_clk {
-	clock-frequency = <32764>;
-};
-
-&spi16 {
-	pinctrl-0 = <&qup_spi16_default>;
-	pinctrl-names = "default";
-	status = "okay";
-};
-
-&tlmm {
-	ethernet0_default: ethernet0-default-state {
-		ethernet0_mdc: ethernet0-mdc-pins {
-			pins = "gpio8";
-			function = "emac0_mdc";
-			drive-strength = <16>;
-			bias-pull-up;
-		};
-
-		ethernet0_mdio: ethernet0-mdio-pins {
-			pins = "gpio9";
-			function = "emac0_mdio";
-			drive-strength = <16>;
-			bias-pull-up;
-		};
-	};
-
-	qup_uart10_default: qup-uart10-state {
-		pins = "gpio46", "gpio47";
-		function = "qup1_se3";
-	};
-
-	qup_spi16_default: qup-spi16-state {
-		pins = "gpio86", "gpio87", "gpio88", "gpio89";
-		function = "qup2_se2";
-		drive-strength = <6>;
-		bias-disable;
-	};
-
-	qup_i2c11_default: qup-i2c11-state {
-		pins = "gpio48", "gpio49";
-		function = "qup1_se4";
-		drive-strength = <2>;
-		bias-pull-up;
-	};
-
-	qup_i2c18_default: qup-i2c18-state {
-		pins = "gpio95", "gpio96";
-		function = "qup2_se4";
-		drive-strength = <2>;
-		bias-pull-up;
-	};
-
-	qup_uart12_default: qup-uart12-state {
-		qup_uart12_cts: qup-uart12-cts-pins {
-			pins = "gpio52";
-			function = "qup1_se5";
-			bias-disable;
-		};
-
-		qup_uart12_rts: qup-uart12-rts-pins {
-			pins = "gpio53";
-			function = "qup1_se5";
-			bias-pull-down;
-		};
-
-		qup_uart12_tx: qup-uart12-tx-pins {
-			pins = "gpio54";
-			function = "qup1_se5";
-			bias-pull-up;
-		};
-
-		qup_uart12_rx: qup-uart12-rx-pins {
-			pins = "gpio55";
-			function = "qup1_se5";
-			bias-pull-down;
-		};
-	};
-
-	qup_uart17_default: qup-uart17-state {
-		qup_uart17_cts: qup-uart17-cts-pins {
-			pins = "gpio91";
-			function = "qup2_se3";
-			bias-disable;
-		};
-
-		qup_uart17_rts: qup0-uart17-rts-pins {
-			pins = "gpio92";
-			function = "qup2_se3";
-			bias-pull-down;
-		};
-
-		qup_uart17_tx: qup0-uart17-tx-pins {
-			pins = "gpio93";
-			function = "qup2_se3";
-			bias-pull-up;
-		};
-
-		qup_uart17_rx: qup0-uart17-rx-pins {
-			pins = "gpio94";
-			function = "qup2_se3";
-			bias-pull-down;
-		};
-	};
-
-	pcie0_default_state: pcie0-default-state {
-		perst-pins {
-			pins = "gpio2";
-			function = "gpio";
-			drive-strength = <2>;
-			bias-pull-down;
-		};
-
-		clkreq-pins {
-			pins = "gpio1";
-			function = "pcie0_clkreq";
-			drive-strength = <2>;
-			bias-pull-up;
-		};
-
-		wake-pins {
-			pins = "gpio0";
-			function = "gpio";
-			drive-strength = <2>;
-			bias-pull-up;
-		};
-	};
-
-	pcie1_default_state: pcie1-default-state {
-		perst-pins {
-			pins = "gpio4";
-			function = "gpio";
-			drive-strength = <2>;
-			bias-pull-down;
-		};
-
-		clkreq-pins {
-			pins = "gpio3";
-			function = "pcie1_clkreq";
-			drive-strength = <2>;
-			bias-pull-up;
-		};
-
-		wake-pins {
-			pins = "gpio5";
-			function = "gpio";
-			drive-strength = <2>;
-			bias-pull-up;
-		};
-	};
-};
-
-&pcie0 {
-	perst-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
-	wake-gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&pcie0_default_state>;
-
-	status = "okay";
-};
-
-&pcie1 {
-	perst-gpios = <&tlmm 4 GPIO_ACTIVE_LOW>;
-	wake-gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>;
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&pcie1_default_state>;
-
-	status = "okay";
-};
-
-&pcie0_phy {
-	vdda-phy-supply = <&vreg_l5a>;
-	vdda-pll-supply = <&vreg_l1c>;
-
-	status = "okay";
-};
-
-&pcie1_phy {
-	vdda-phy-supply = <&vreg_l5a>;
-	vdda-pll-supply = <&vreg_l1c>;
-
-	status = "okay";
-};
-
-&uart10 {
-	compatible = "qcom,geni-debug-uart";
-	pinctrl-0 = <&qup_uart10_default>;
-	pinctrl-names = "default";
-	status = "okay";
-};
-
-&uart12 {
-	pinctrl-0 = <&qup_uart12_default>;
-	pinctrl-names = "default";
-	status = "okay";
-};
-
-&uart17 {
-	pinctrl-0 = <&qup_uart17_default>;
-	pinctrl-names = "default";
-	status = "okay";
-};
-
-&ufs_mem_hc {
-	reset-gpios = <&tlmm 149 GPIO_ACTIVE_LOW>;
-	vcc-supply = <&vreg_l8a>;
-	vcc-max-microamp = <1100000>;
-	vccq-supply = <&vreg_l4c>;
-	vccq-max-microamp = <1200000>;
-
-	status = "okay";
-};
-
-&ufs_mem_phy {
-	vdda-phy-supply = <&vreg_l4a>;
-	vdda-pll-supply = <&vreg_l1c>;
-
-	status = "okay";
-};
-
-&usb_0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb0_en_state>;
-
-	status = "okay";
-};
-
-&usb_0_dwc3 {
-	dr_mode = "peripheral";
-};
-
-&usb_0_hsphy {
-	vdda-pll-supply = <&vreg_l7a>;
-	vdda18-supply = <&vreg_l6c>;
-	vdda33-supply = <&vreg_l9a>;
-
-	status = "okay";
-};
-
-&usb_0_qmpphy {
-	vdda-phy-supply = <&vreg_l1c>;
-	vdda-pll-supply = <&vreg_l7a>;
-
-	status = "okay";
-};
-
-&usb_1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb1_en_state>;
-
-	status = "okay";
-};
-
-&usb_1_dwc3 {
-	dr_mode = "host";
-};
-
-&usb_1_hsphy {
-	vdda-pll-supply = <&vreg_l7a>;
-	vdda18-supply = <&vreg_l6c>;
-	vdda33-supply = <&vreg_l9a>;
-
-	status = "okay";
-};
-
-&usb_1_qmpphy {
-	vdda-phy-supply = <&vreg_l1c>;
-	vdda-pll-supply = <&vreg_l7a>;
-
-	status = "okay";
-};
-
-&usb_2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb2_en_state>;
-
-	status = "okay";
-};
-
-&usb_2_dwc3 {
-	dr_mode = "host";
-};
-
-&usb_2_hsphy {
-	vdda-pll-supply = <&vreg_l7a>;
-	vdda18-supply = <&vreg_l6c>;
-	vdda33-supply = <&vreg_l9a>;
-
-	status = "okay";
-};
-
-&xo_board_clk {
-	clock-frequency = <38400000>;
-};
diff --git a/arch/arm64/boot/dts/qcom/sa8775p-ride.dtsi b/arch/arm64/boot/dts/qcom/sa8775p-ride.dtsi
new file mode 100644
index 000000000000..2a6170623ea9
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sa8775p-ride.dtsi
@@ -0,0 +1,814 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023, Linaro Limited
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+#include "sa8775p.dtsi"
+#include "sa8775p-pmics.dtsi"
+
+/ {
+	aliases {
+		ethernet0 = &ethernet0;
+		ethernet1 = &ethernet1;
+		i2c11 = &i2c11;
+		i2c18 = &i2c18;
+		serial0 = &uart10;
+		serial1 = &uart12;
+		serial2 = &uart17;
+		spi16 = &spi16;
+		ufshc1 = &ufs_mem_hc;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pmm8654au-rpmh-regulators";
+		qcom,pmic-id = "a";
+
+		vreg_s4a: smps4 {
+			regulator-name = "vreg_s4a";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1816000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s5a: smps5 {
+			regulator-name = "vreg_s5a";
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <1996000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s9a: smps9 {
+			regulator-name = "vreg_s9a";
+			regulator-min-microvolt = <535000>;
+			regulator-max-microvolt = <1120000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4a: ldo4 {
+			regulator-name = "vreg_l4a";
+			regulator-min-microvolt = <788000>;
+			regulator-max-microvolt = <1050000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5a: ldo5 {
+			regulator-name = "vreg_l5a";
+			regulator-min-microvolt = <870000>;
+			regulator-max-microvolt = <950000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6a: ldo6 {
+			regulator-name = "vreg_l6a";
+			regulator-min-microvolt = <870000>;
+			regulator-max-microvolt = <970000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7a: ldo7 {
+			regulator-name = "vreg_l7a";
+			regulator-min-microvolt = <720000>;
+			regulator-max-microvolt = <950000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8a: ldo8 {
+			regulator-name = "vreg_l8a";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9a: ldo9 {
+			regulator-name = "vreg_l9a";
+			regulator-min-microvolt = <2970000>;
+			regulator-max-microvolt = <3544000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,pmm8654au-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vreg_l1c: ldo1 {
+			regulator-name = "vreg_l1c";
+			regulator-min-microvolt = <1140000>;
+			regulator-max-microvolt = <1260000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2c: ldo2 {
+			regulator-name = "vreg_l2c";
+			regulator-min-microvolt = <900000>;
+			regulator-max-microvolt = <1100000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3c: ldo3 {
+			regulator-name = "vreg_l3c";
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4c: ldo4 {
+			regulator-name = "vreg_l4c";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			/*
+			 * FIXME: This should have regulator-allow-set-load but
+			 * we're getting an over-current fault from the PMIC
+			 * when switching to LPM.
+			 */
+		};
+
+		vreg_l5c: ldo5 {
+			regulator-name = "vreg_l5c";
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6c: ldo6 {
+			regulator-name = "vreg_l6c";
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <1980000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7c: ldo7 {
+			regulator-name = "vreg_l7c";
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8c: ldo8 {
+			regulator-name = "vreg_l8c";
+			regulator-min-microvolt = <2400000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9c: ldo9 {
+			regulator-name = "vreg_l9c";
+			regulator-min-microvolt = <1650000>;
+			regulator-max-microvolt = <2700000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-2 {
+		compatible = "qcom,pmm8654au-rpmh-regulators";
+		qcom,pmic-id = "e";
+
+		vreg_s4e: smps4 {
+			regulator-name = "vreg_s4e";
+			regulator-min-microvolt = <970000>;
+			regulator-max-microvolt = <1520000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s7e: smps7 {
+			regulator-name = "vreg_s7e";
+			regulator-min-microvolt = <1010000>;
+			regulator-max-microvolt = <1170000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s9e: smps9 {
+			regulator-name = "vreg_s9e";
+			regulator-min-microvolt = <300000>;
+			regulator-max-microvolt = <570000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6e: ldo6 {
+			regulator-name = "vreg_l6e";
+			regulator-min-microvolt = <1280000>;
+			regulator-max-microvolt = <1450000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8e: ldo8 {
+			regulator-name = "vreg_l8e";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1950000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+};
+
+&ethernet0 {
+	phy-handle = <&sgmii_phy0>;
+
+	pinctrl-0 = <&ethernet0_default>;
+	pinctrl-names = "default";
+
+	snps,mtl-rx-config = <&mtl_rx_setup>;
+	snps,mtl-tx-config = <&mtl_tx_setup>;
+	snps,ps-speed = <1000>;
+
+	status = "okay";
+
+	mdio: mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	mtl_rx_setup: rx-queues-config {
+		snps,rx-queues-to-use = <4>;
+		snps,rx-sched-sp;
+
+		queue0 {
+			snps,dcb-algorithm;
+			snps,map-to-dma-channel = <0x0>;
+			snps,route-up;
+			snps,priority = <0x1>;
+		};
+
+		queue1 {
+			snps,dcb-algorithm;
+			snps,map-to-dma-channel = <0x1>;
+			snps,route-ptp;
+		};
+
+		queue2 {
+			snps,avb-algorithm;
+			snps,map-to-dma-channel = <0x2>;
+			snps,route-avcp;
+		};
+
+		queue3 {
+			snps,avb-algorithm;
+			snps,map-to-dma-channel = <0x3>;
+			snps,priority = <0xc>;
+		};
+	};
+
+	mtl_tx_setup: tx-queues-config {
+		snps,tx-queues-to-use = <4>;
+		snps,tx-sched-sp;
+
+		queue0 {
+			snps,dcb-algorithm;
+		};
+
+		queue1 {
+			snps,dcb-algorithm;
+		};
+
+		queue2 {
+			snps,avb-algorithm;
+			snps,send_slope = <0x1000>;
+			snps,idle_slope = <0x1000>;
+			snps,high_credit = <0x3e800>;
+			snps,low_credit = <0xffc18000>;
+		};
+
+		queue3 {
+			snps,avb-algorithm;
+			snps,send_slope = <0x1000>;
+			snps,idle_slope = <0x1000>;
+			snps,high_credit = <0x3e800>;
+			snps,low_credit = <0xffc18000>;
+		};
+	};
+};
+
+&ethernet1 {
+	phy-handle = <&sgmii_phy1>;
+
+	snps,mtl-rx-config = <&mtl_rx_setup1>;
+	snps,mtl-tx-config = <&mtl_tx_setup1>;
+	snps,ps-speed = <1000>;
+
+	status = "okay";
+
+	mtl_rx_setup1: rx-queues-config {
+		snps,rx-queues-to-use = <4>;
+		snps,rx-sched-sp;
+
+		queue0 {
+			snps,dcb-algorithm;
+			snps,map-to-dma-channel = <0x0>;
+			snps,route-up;
+			snps,priority = <0x1>;
+		};
+
+		queue1 {
+			snps,dcb-algorithm;
+			snps,map-to-dma-channel = <0x1>;
+			snps,route-ptp;
+		};
+
+		queue2 {
+			snps,avb-algorithm;
+			snps,map-to-dma-channel = <0x2>;
+			snps,route-avcp;
+		};
+
+		queue3 {
+			snps,avb-algorithm;
+			snps,map-to-dma-channel = <0x3>;
+			snps,priority = <0xc>;
+		};
+	};
+
+	mtl_tx_setup1: tx-queues-config {
+		snps,tx-queues-to-use = <4>;
+		snps,tx-sched-sp;
+
+		queue0 {
+			snps,dcb-algorithm;
+		};
+
+		queue1 {
+			snps,dcb-algorithm;
+		};
+
+		queue2 {
+			snps,avb-algorithm;
+			snps,send_slope = <0x1000>;
+			snps,idle_slope = <0x1000>;
+			snps,high_credit = <0x3e800>;
+			snps,low_credit = <0xffc18000>;
+		};
+
+		queue3 {
+			snps,avb-algorithm;
+			snps,send_slope = <0x1000>;
+			snps,idle_slope = <0x1000>;
+			snps,high_credit = <0x3e800>;
+			snps,low_credit = <0xffc18000>;
+		};
+	};
+};
+
+&i2c11 {
+	clock-frequency = <400000>;
+	pinctrl-0 = <&qup_i2c11_default>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&i2c18 {
+	clock-frequency = <400000>;
+	pinctrl-0 = <&qup_i2c18_default>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&pmm8654au_0_gpios {
+	gpio-line-names = "DS_EN",
+			  "POFF_COMPLETE",
+			  "UFS0_VER_ID",
+			  "FAST_POFF",
+			  "DBU1_PON_DONE",
+			  "AOSS_SLEEP",
+			  "CAM_DES0_EN",
+			  "CAM_DES1_EN",
+			  "CAM_DES2_EN",
+			  "CAM_DES3_EN",
+			  "UEFI",
+			  "ANALOG_PON_OPT";
+};
+
+&pmm8654au_0_pon_resin {
+	linux,code = <KEY_VOLUMEDOWN>;
+	status = "okay";
+};
+
+&pmm8654au_1_gpios {
+	gpio-line-names = "PMIC_C_ID0",
+			  "PMIC_C_ID1",
+			  "UFS1_VER_ID",
+			  "IPA_PWR",
+			  "",
+			  "WLAN_DBU4_EN",
+			  "WLAN_EN",
+			  "BT_EN",
+			  "USB2_PWR_EN",
+			  "USB2_FAULT";
+
+	usb2_en_state: usb2-en-state {
+		pins = "gpio9";
+		function = "normal";
+		output-high;
+		power-source = <0>;
+	};
+};
+
+&pmm8654au_2_gpios {
+	gpio-line-names = "PMIC_E_ID0",
+			  "PMIC_E_ID1",
+			  "USB0_PWR_EN",
+			  "USB0_FAULT",
+			  "SENSOR_IRQ_1",
+			  "SENSOR_IRQ_2",
+			  "SENSOR_RST",
+			  "SGMIIO0_RST",
+			  "SGMIIO1_RST",
+			  "USB1_PWR_ENABLE",
+			  "USB1_FAULT",
+			  "VMON_SPX8";
+
+	usb0_en_state: usb0-en-state {
+		pins = "gpio3";
+		function = "normal";
+		output-high;
+		power-source = <0>;
+	};
+
+	usb1_en_state: usb1-en-state {
+		pins = "gpio10";
+		function = "normal";
+		output-high;
+		power-source = <0>;
+	};
+};
+
+&pmm8654au_3_gpios {
+	gpio-line-names = "PMIC_G_ID0",
+			  "PMIC_G_ID1",
+			  "GNSS_RST",
+			  "GNSS_EN",
+			  "GNSS_BOOT_MODE";
+};
+
+&qupv3_id_1 {
+	status = "okay";
+};
+
+&qupv3_id_2 {
+	status = "okay";
+};
+
+&serdes0 {
+	phy-supply = <&vreg_l5a>;
+	status = "okay";
+};
+
+&serdes1 {
+	phy-supply = <&vreg_l5a>;
+	status = "okay";
+};
+
+&sleep_clk {
+	clock-frequency = <32764>;
+};
+
+&spi16 {
+	pinctrl-0 = <&qup_spi16_default>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&tlmm {
+	ethernet0_default: ethernet0-default-state {
+		ethernet0_mdc: ethernet0-mdc-pins {
+			pins = "gpio8";
+			function = "emac0_mdc";
+			drive-strength = <16>;
+			bias-pull-up;
+		};
+
+		ethernet0_mdio: ethernet0-mdio-pins {
+			pins = "gpio9";
+			function = "emac0_mdio";
+			drive-strength = <16>;
+			bias-pull-up;
+		};
+	};
+
+	qup_uart10_default: qup-uart10-state {
+		pins = "gpio46", "gpio47";
+		function = "qup1_se3";
+	};
+
+	qup_spi16_default: qup-spi16-state {
+		pins = "gpio86", "gpio87", "gpio88", "gpio89";
+		function = "qup2_se2";
+		drive-strength = <6>;
+		bias-disable;
+	};
+
+	qup_i2c11_default: qup-i2c11-state {
+		pins = "gpio48", "gpio49";
+		function = "qup1_se4";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+
+	qup_i2c18_default: qup-i2c18-state {
+		pins = "gpio95", "gpio96";
+		function = "qup2_se4";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+
+	qup_uart12_default: qup-uart12-state {
+		qup_uart12_cts: qup-uart12-cts-pins {
+			pins = "gpio52";
+			function = "qup1_se5";
+			bias-disable;
+		};
+
+		qup_uart12_rts: qup-uart12-rts-pins {
+			pins = "gpio53";
+			function = "qup1_se5";
+			bias-pull-down;
+		};
+
+		qup_uart12_tx: qup-uart12-tx-pins {
+			pins = "gpio54";
+			function = "qup1_se5";
+			bias-pull-up;
+		};
+
+		qup_uart12_rx: qup-uart12-rx-pins {
+			pins = "gpio55";
+			function = "qup1_se5";
+			bias-pull-down;
+		};
+	};
+
+	qup_uart17_default: qup-uart17-state {
+		qup_uart17_cts: qup-uart17-cts-pins {
+			pins = "gpio91";
+			function = "qup2_se3";
+			bias-disable;
+		};
+
+		qup_uart17_rts: qup0-uart17-rts-pins {
+			pins = "gpio92";
+			function = "qup2_se3";
+			bias-pull-down;
+		};
+
+		qup_uart17_tx: qup0-uart17-tx-pins {
+			pins = "gpio93";
+			function = "qup2_se3";
+			bias-pull-up;
+		};
+
+		qup_uart17_rx: qup0-uart17-rx-pins {
+			pins = "gpio94";
+			function = "qup2_se3";
+			bias-pull-down;
+		};
+	};
+
+	pcie0_default_state: pcie0-default-state {
+		perst-pins {
+			pins = "gpio2";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+
+		clkreq-pins {
+			pins = "gpio1";
+			function = "pcie0_clkreq";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		wake-pins {
+			pins = "gpio0";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	pcie1_default_state: pcie1-default-state {
+		perst-pins {
+			pins = "gpio4";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+
+		clkreq-pins {
+			pins = "gpio3";
+			function = "pcie1_clkreq";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		wake-pins {
+			pins = "gpio5";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+};
+
+&pcie0 {
+	perst-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie0_default_state>;
+
+	status = "okay";
+};
+
+&pcie1 {
+	perst-gpios = <&tlmm 4 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie1_default_state>;
+
+	status = "okay";
+};
+
+&pcie0_phy {
+	vdda-phy-supply = <&vreg_l5a>;
+	vdda-pll-supply = <&vreg_l1c>;
+
+	status = "okay";
+};
+
+&pcie1_phy {
+	vdda-phy-supply = <&vreg_l5a>;
+	vdda-pll-supply = <&vreg_l1c>;
+
+	status = "okay";
+};
+
+&uart10 {
+	compatible = "qcom,geni-debug-uart";
+	pinctrl-0 = <&qup_uart10_default>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&uart12 {
+	pinctrl-0 = <&qup_uart12_default>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&uart17 {
+	pinctrl-0 = <&qup_uart17_default>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&ufs_mem_hc {
+	reset-gpios = <&tlmm 149 GPIO_ACTIVE_LOW>;
+	vcc-supply = <&vreg_l8a>;
+	vcc-max-microamp = <1100000>;
+	vccq-supply = <&vreg_l4c>;
+	vccq-max-microamp = <1200000>;
+
+	status = "okay";
+};
+
+&ufs_mem_phy {
+	vdda-phy-supply = <&vreg_l4a>;
+	vdda-pll-supply = <&vreg_l1c>;
+
+	status = "okay";
+};
+
+&usb_0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_en_state>;
+
+	status = "okay";
+};
+
+&usb_0_dwc3 {
+	dr_mode = "peripheral";
+};
+
+&usb_0_hsphy {
+	vdda-pll-supply = <&vreg_l7a>;
+	vdda18-supply = <&vreg_l6c>;
+	vdda33-supply = <&vreg_l9a>;
+
+	status = "okay";
+};
+
+&usb_0_qmpphy {
+	vdda-phy-supply = <&vreg_l1c>;
+	vdda-pll-supply = <&vreg_l7a>;
+
+	status = "okay";
+};
+
+&usb_1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb1_en_state>;
+
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_1_hsphy {
+	vdda-pll-supply = <&vreg_l7a>;
+	vdda18-supply = <&vreg_l6c>;
+	vdda33-supply = <&vreg_l9a>;
+
+	status = "okay";
+};
+
+&usb_1_qmpphy {
+	vdda-phy-supply = <&vreg_l1c>;
+	vdda-pll-supply = <&vreg_l7a>;
+
+	status = "okay";
+};
+
+&usb_2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb2_en_state>;
+
+	status = "okay";
+};
+
+&usb_2_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_2_hsphy {
+	vdda-pll-supply = <&vreg_l7a>;
+	vdda18-supply = <&vreg_l6c>;
+	vdda33-supply = <&vreg_l9a>;
+
+	status = "okay";
+};
+
+&xo_board_clk {
+	clock-frequency = <38400000>;
+};
-- 
2.43.0

[PATCH v2 3/3] arm64: dts: qcom: sa8775p-ride-r3: add new board file

[Bartosz Golaszewski]

From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

Revision 3 of the sa8775p-ride board uses a different PHY for the two
ethernet ports and supports 2.5G speed. Create a new file for the board
reflecting the changes.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
---
 arch/arm64/boot/dts/qcom/Makefile            |  1 +
 arch/arm64/boot/dts/qcom/sa8775p-ride-r3.dts | 47 ++++++++++++++++++++
 2 files changed, 48 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sa8775p-ride-r3.dts

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 5576c7d6ea06..8b7a81b82213 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -113,6 +113,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sa8155p-adp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sa8295p-adp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sa8540p-ride.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sa8775p-ride.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sa8775p-ride-r3.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-acer-aspire1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-idp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-coachz-r1.dtb
diff --git a/arch/arm64/boot/dts/qcom/sa8775p-ride-r3.dts b/arch/arm64/boot/dts/qcom/sa8775p-ride-r3.dts
new file mode 100644
index 000000000000..d214a87d69b2
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sa8775p-ride-r3.dts
@@ -0,0 +1,47 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023, Linaro Limited
+ */
+
+/dts-v1/;
+
+#include "sa8775p-ride.dtsi"
+
+/ {
+	model = "Qualcomm SA8775P Ride Rev3";
+	compatible = "qcom,sa8775p-ride-r3", "qcom,sa8775p";
+};
+
+&ethernet0 {
+	phy-mode = "ocsgmii";
+};
+
+&ethernet1 {
+	phy-mode = "ocsgmii";
+};
+
+&mdio {
+	compatible = "snps,dwmac-mdio";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	sgmii_phy0: phy@8 {
+		compatible = "ethernet-phy-id31c3.1c33";
+		reg = <0x8>;
+		device_type = "ethernet-phy";
+		interrupts-extended = <&tlmm 7 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&pmm8654au_2_gpios 8 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <11000>;
+		reset-deassert-us = <70000>;
+	};
+
+	sgmii_phy1: phy@0 {
+		compatible = "ethernet-phy-id31c3.1c33";
+		reg = <0x0>;
+		device_type = "ethernet-phy";
+		interrupts-extended = <&tlmm 26 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&pmm8654au_2_gpios 9 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <11000>;
+		reset-deassert-us = <70000>;
+	};
+};
-- 
2.43.0

Re: [PATCH v2 0/3] arm64: dts: qcom: sa8775p-ride: support both board variants

[Bartosz Golaszewski]

On Tue, Jun 25, 2024 at 5:14 PM Bartosz Golaszewski <brgl@bgdev.pl> wrote:
>
> From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
>
> Split the current .dts into two: the existing one keeps the name and
> supports revision 2 of the board while patch 2 adds a .dts for revision 3.
>
> Changes since v1:
> - add a new compatible for Rev3
>
> Bartosz Golaszewski (3):
>   dt-bindings: arm: qcom: add sa8775p-ride Rev 3
>   arm64: dts: qcom: move common parts for sa8775p-ride variants into a
>     .dtsi
>   arm64: dts: qcom: sa8775p-ride-r3: add new board file
>
>  .../devicetree/bindings/arm/qcom.yaml         |   1 +
>  arch/arm64/boot/dts/qcom/Makefile             |   1 +
>  arch/arm64/boot/dts/qcom/sa8775p-ride-r3.dts  |  47 +
>  arch/arm64/boot/dts/qcom/sa8775p-ride.dts     | 836 +-----------------
>  arch/arm64/boot/dts/qcom/sa8775p-ride.dtsi    | 814 +++++++++++++++++
>  5 files changed, 885 insertions(+), 814 deletions(-)
>  create mode 100644 arch/arm64/boot/dts/qcom/sa8775p-ride-r3.dts
>  create mode 100644 arch/arm64/boot/dts/qcom/sa8775p-ride.dtsi
>
> --
> 2.43.0
>

Eeek -ETOOEARLY, please disregard this one, it requires one more
change. Sorry for the noise.

Bartosz

Re: [PATCH v2 1/3] dt-bindings: arm: qcom: add sa8775p-ride Rev 3

[Krzysztof Kozlowski]

On 25/06/2024 17:14, Bartosz Golaszewski wrote:
> From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> 
> Document the compatible for revision 3 of the sa8775p-ride board.
> 
> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> ---
>  Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
>  1 file changed, 1 insertion(+)
> 
> diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
> index ec1c10a12470..000037f4a712 100644
> --- a/Documentation/devicetree/bindings/arm/qcom.yaml
> +++ b/Documentation/devicetree/bindings/arm/qcom.yaml
> @@ -895,6 +895,7 @@ properties:
>        - items:
>            - enum:
>                - qcom,sa8775p-ride
> +              - qcom,sa8775p-ride-r3

The board is not compatible with earlier revision?

Best regards,
Krzysztof

Re: [PATCH v2 1/3] dt-bindings: arm: qcom: add sa8775p-ride Rev 3

[Bartosz Golaszewski]

On Wed, Jun 26, 2024 at 11:00 AM Krzysztof Kozlowski <krzk@kernel.org> wrote:
>
> On 25/06/2024 17:14, Bartosz Golaszewski wrote:
> > From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> >
> > Document the compatible for revision 3 of the sa8775p-ride board.
> >
> > Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> > ---
> >  Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
> >  1 file changed, 1 insertion(+)
> >
> > diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
> > index ec1c10a12470..000037f4a712 100644
> > --- a/Documentation/devicetree/bindings/arm/qcom.yaml
> > +++ b/Documentation/devicetree/bindings/arm/qcom.yaml
> > @@ -895,6 +895,7 @@ properties:
> >        - items:
> >            - enum:
> >                - qcom,sa8775p-ride
> > +              - qcom,sa8775p-ride-r3
>
> The board is not compatible with earlier revision?
>

In what way? Can you run the same DTB on both? Sure. Will ethernet
work in both cases? No.

Bart

Re: [PATCH v2 1/3] dt-bindings: arm: qcom: add sa8775p-ride Rev 3

[Krzysztof Kozlowski]

On 26/06/2024 13:02, Bartosz Golaszewski wrote:
> On Wed, Jun 26, 2024 at 11:00 AM Krzysztof Kozlowski <krzk@kernel.org> wrote:
>>
>> On 25/06/2024 17:14, Bartosz Golaszewski wrote:
>>> From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
>>>
>>> Document the compatible for revision 3 of the sa8775p-ride board.
>>>
>>> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
>>> ---
>>>  Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
>>>  1 file changed, 1 insertion(+)
>>>
>>> diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
>>> index ec1c10a12470..000037f4a712 100644
>>> --- a/Documentation/devicetree/bindings/arm/qcom.yaml
>>> +++ b/Documentation/devicetree/bindings/arm/qcom.yaml
>>> @@ -895,6 +895,7 @@ properties:
>>>        - items:
>>>            - enum:
>>>                - qcom,sa8775p-ride
>>> +              - qcom,sa8775p-ride-r3
>>
>> The board is not compatible with earlier revision?
>>
> 
> In what way? Can you run the same DTB on both? Sure. Will ethernet
> work in both cases? No.

OK

Best regards,
Krzysztof

Re: [PATCH v2 0/3] arm64: dts: qcom: sa8775p-ride: support both board variants

[Rob Herring (Arm)]

On Tue, 25 Jun 2024 17:14:27 +0200, Bartosz Golaszewski wrote:
> From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> 
> Split the current .dts into two: the existing one keeps the name and
> supports revision 2 of the board while patch 2 adds a .dts for revision 3.
> 
> Changes since v1:
> - add a new compatible for Rev3
> 
> Bartosz Golaszewski (3):
>   dt-bindings: arm: qcom: add sa8775p-ride Rev 3
>   arm64: dts: qcom: move common parts for sa8775p-ride variants into a
>     .dtsi
>   arm64: dts: qcom: sa8775p-ride-r3: add new board file
> 
>  .../devicetree/bindings/arm/qcom.yaml         |   1 +
>  arch/arm64/boot/dts/qcom/Makefile             |   1 +
>  arch/arm64/boot/dts/qcom/sa8775p-ride-r3.dts  |  47 +
>  arch/arm64/boot/dts/qcom/sa8775p-ride.dts     | 836 +-----------------
>  arch/arm64/boot/dts/qcom/sa8775p-ride.dtsi    | 814 +++++++++++++++++
>  5 files changed, 885 insertions(+), 814 deletions(-)
>  create mode 100644 arch/arm64/boot/dts/qcom/sa8775p-ride-r3.dts
>  create mode 100644 arch/arm64/boot/dts/qcom/sa8775p-ride.dtsi
> 
> --
> 2.43.0
> 
> 
> 


My bot found new DTB warnings on the .dts files added or changed in this
series.

Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.

If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:

  pip3 install dtschema --upgrade


New warnings running 'make CHECK_DTBS=y qcom/sa8775p-ride-r3.dtb qcom/sa8775p-ride.dtb' for 20240625151430.34024-1-brgl@bgdev.pl:

arch/arm64/boot/dts/qcom/sa8775p-ride-r3.dtb: usb@a4f8800: interrupt-names: ['pwr_event', 'hs_phy_irq', 'dp_hs_phy_irq', 'dm_hs_phy_irq'] is too short
	from schema $id: http://devicetree.org/schemas/usb/qcom,dwc3.yaml#
arch/arm64/boot/dts/qcom/sa8775p-ride-r3.dtb: rsc@18200000: 'power-domains' is a required property
	from schema $id: http://devicetree.org/schemas/soc/qcom/qcom,rpmh-rsc.yaml#
arch/arm64/boot/dts/qcom/sa8775p-ride-r3.dtb: ethernet@23000000: tx-queues-config: 'snps,tx-sched-sp' does not match any of the regexes: '^queue[0-9]$', 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/net/qcom,ethqos.yaml#
arch/arm64/boot/dts/qcom/sa8775p-ride-r3.dtb: ethernet@23000000: phy-mode:0: 'ocsgmii' is not one of ['internal', 'mii', 'gmii', 'sgmii', 'psgmii', 'qsgmii', 'qusgmii', 'tbi', 'rev-mii', 'rmii', 'rev-rmii', 'moca', 'rgmii', 'rgmii-id', 'rgmii-rxid', 'rgmii-txid', 'rtbi', 'smii', 'xgmii', 'trgmii', '1000base-x', '2500base-x', '5gbase-r', 'rxaui', 'xaui', '10gbase-kr', 'usxgmii', '10gbase-r', '25gbase-r', '10g-qxgmii']
	from schema $id: http://devicetree.org/schemas/net/qcom,ethqos.yaml#
arch/arm64/boot/dts/qcom/sa8775p-ride-r3.dtb: ethernet@23000000: snps,pbl: [32] is not of type 'integer'
	from schema $id: http://devicetree.org/schemas/net/qcom,ethqos.yaml#
arch/arm64/boot/dts/qcom/sa8775p-ride-r3.dtb: ethernet@23000000: snps,pbl: [32] is not one of [1, 2, 4, 8, 16, 32]
	from schema $id: http://devicetree.org/schemas/net/qcom,ethqos.yaml#
arch/arm64/boot/dts/qcom/sa8775p-ride-r3.dtb: ethernet@23000000: Unevaluated properties are not allowed ('phy-handle', 'phy-mode', 'power-domains', 'rx-fifo-depth', 'rx-queues-config', 'snps,mtl-rx-config', 'snps,mtl-tx-config', 'snps,pbl', 'snps,ps-speed', 'snps,tso', 'tx-fifo-depth', 'tx-queues-config' were unexpected)
	from schema $id: http://devicetree.org/schemas/net/qcom,ethqos.yaml#
arch/arm64/boot/dts/qcom/sa8775p-ride-r3.dtb: ethernet@23000000: phy-mode:0: 'ocsgmii' is not one of ['internal', 'mii', 'gmii', 'sgmii', 'psgmii', 'qsgmii', 'qusgmii', 'tbi', 'rev-mii', 'rmii', 'rev-rmii', 'moca', 'rgmii', 'rgmii-id', 'rgmii-rxid', 'rgmii-txid', 'rtbi', 'smii', 'xgmii', 'trgmii', '1000base-x', '2500base-x', '5gbase-r', 'rxaui', 'xaui', '10gbase-kr', 'usxgmii', '10gbase-r', '25gbase-r', '10g-qxgmii']
	from schema $id: http://devicetree.org/schemas/net/ethernet-controller.yaml#
arch/arm64/boot/dts/qcom/sa8775p-ride-r3.dtb: ethernet@23040000: tx-queues-config: 'snps,tx-sched-sp' does not match any of the regexes: '^queue[0-9]$', 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/net/qcom,ethqos.yaml#
arch/arm64/boot/dts/qcom/sa8775p-ride-r3.dtb: ethernet@23040000: phy-mode:0: 'ocsgmii' is not one of ['internal', 'mii', 'gmii', 'sgmii', 'psgmii', 'qsgmii', 'qusgmii', 'tbi', 'rev-mii', 'rmii', 'rev-rmii', 'moca', 'rgmii', 'rgmii-id', 'rgmii-rxid', 'rgmii-txid', 'rtbi', 'smii', 'xgmii', 'trgmii', '1000base-x', '2500base-x', '5gbase-r', 'rxaui', 'xaui', '10gbase-kr', 'usxgmii', '10gbase-r', '25gbase-r', '10g-qxgmii']
	from schema $id: http://devicetree.org/schemas/net/qcom,ethqos.yaml#
arch/arm64/boot/dts/qcom/sa8775p-ride-r3.dtb: ethernet@23040000: snps,pbl: [32] is not of type 'integer'
	from schema $id: http://devicetree.org/schemas/net/qcom,ethqos.yaml#
arch/arm64/boot/dts/qcom/sa8775p-ride-r3.dtb: ethernet@23040000: snps,pbl: [32] is not one of [1, 2, 4, 8, 16, 32]
	from schema $id: http://devicetree.org/schemas/net/qcom,ethqos.yaml#
arch/arm64/boot/dts/qcom/sa8775p-ride-r3.dtb: ethernet@23040000: Unevaluated properties are not allowed ('mdio', 'phy-handle', 'phy-mode', 'power-domains', 'rx-fifo-depth', 'rx-queues-config', 'snps,mtl-rx-config', 'snps,mtl-tx-config', 'snps,pbl', 'snps,ps-speed', 'snps,tso', 'tx-fifo-depth', 'tx-queues-config' were unexpected)
	from schema $id: http://devicetree.org/schemas/net/qcom,ethqos.yaml#
arch/arm64/boot/dts/qcom/sa8775p-ride-r3.dtb: ethernet@23040000: phy-mode:0: 'ocsgmii' is not one of ['internal', 'mii', 'gmii', 'sgmii', 'psgmii', 'qsgmii', 'qusgmii', 'tbi', 'rev-mii', 'rmii', 'rev-rmii', 'moca', 'rgmii', 'rgmii-id', 'rgmii-rxid', 'rgmii-txid', 'rtbi', 'smii', 'xgmii', 'trgmii', '1000base-x', '2500base-x', '5gbase-r', 'rxaui', 'xaui', '10gbase-kr', 'usxgmii', '10gbase-r', '25gbase-r', '10g-qxgmii']
	from schema $id: http://devicetree.org/schemas/net/ethernet-controller.yaml#

Re: [PATCH v2 3/3] arm64: dts: qcom: sa8775p-ride-r3: add new board file

[Konrad Dybcio]

On 25.06.2024 5:14 PM, Bartosz Golaszewski wrote:
> From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> 
> Revision 3 of the sa8775p-ride board uses a different PHY for the two
> ethernet ports and supports 2.5G speed. Create a new file for the board
> reflecting the changes.
> 
> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> ---

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad