From: Icenowy Zheng <icenowy@aosc.io>
To: Chen-Yu Tsai <wens@csie.org>,
Maxime Ripard <maxime.ripard@bootlin.com>,
Lee Jones <lee.jones@linaro.org>,
Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>
Cc: Andre Przywara <andre.przywara@arm.com>,
linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org
Subject: Re: [PATCH 5/5] arm64: dts: allwinner: h6: enable AXP805 PMIC on Pine H64
Date: Tue, 26 Jun 2018 08:49:41 +0800 [thread overview]
Message-ID: <f93b1524657048279f54004fdbcd6ab5af9ec1c1.camel@aosc.io> (raw)
In-Reply-To: <20180620051540.25617-6-wens@csie.org>
在 2018-06-20三的 13:15 +0800，Chen-Yu Tsai写道：
> From: Icenowy Zheng <icenowy@aosc.io>
>
> Pine H64 board has an AXP805 PMIC on it.
>
> Enable it in the device tree.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
I suggest to mention the working mode change here.
> Signed-off-by: Chen-Yu Tsai <wens@csie.org>
> ---
> .../boot/dts/allwinner/sun50i-h6-pine-h64.dts | 109
> ++++++++++++++++++
> 1 file changed, 109 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts
> b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts
> index 2e97173c9204..1673636358ef 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts
> @@ -44,6 +44,115 @@
> &r_i2c {
> status = "okay";
>
> + axp805: pmic@36 {
> + compatible = "x-powers,axp805", "x-powers,axp806";
> + reg = <0x36>;
> + interrupt-parent = <&r_intc>;
> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> + x-powers,self-working-mode;
> +
> + regulators {
> + reg_aldo1: aldo1 {
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-pl";
> + };
> +
> + reg_aldo2: aldo2 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-ac200";
> + };
> +
> + reg_aldo3: aldo3 {
> + /* This regulator is connected with
> CLDO1 */
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-3v3-1";
> + };
> +
> + reg_bldo1: bldo1 {
> + regulator-always-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc-bias-pll";
> + };
> +
> + reg_bldo2: bldo2 {
> + regulator-always-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc-efuse-pcie-
> hdmi-io";
> + };
> +
> + reg_bldo3: bldo3 {
> + regulator-always-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc-dcxoio";
> + };
> +
> + bldo4 {
> + /* unused */
> + };
> +
> + reg_cldo1: cldo1 {
> + /* This regulator is connected with
> ALDO3 */
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-3v3-2";
> + };
> +
> + reg_cldo2: cldo2 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-wifi-1";
> + };
> +
> + reg_cldo3: cldo3 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-wifi-2";
> + };
> +
> + reg_dcdca: dcdca {
> + regulator-always-on;
> + regulator-min-microvolt = <810000>;
> + regulator-max-microvolt = <1080000>;
> + regulator-name = "vdd-cpu";
> + };
> +
> + reg_dcdcc: dcdcc {
> + regulator-min-microvolt = <810000>;
> + regulator-max-microvolt = <1080000>;
> + regulator-name = "vdd-gpu";
> + };
> +
> + reg_dcdcd: dcdcd {
> + regulator-always-on;
> + regulator-min-microvolt = <960000>;
> + regulator-max-microvolt = <960000>;
> + regulator-name = "vdd-sys";
> + };
> +
> + reg_dcdce: dcdce {
> + regulator-always-on;
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-name = "vcc-dram";
> + };
> +
> + sw {
> + /* unused */
> + };
> + };
> + };
> +
> pcf8563: rtc@51 {
> compatible = "nxp,pcf8563";
> reg = <0x51>;
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2018-06-26 0:49 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-06-20 5:15 [PATCH 0/5] arm64: allwinner: h6: Enable AXP805 PMIC on Pine H64 Chen-Yu Tsai
2018-06-20 5:15 ` [PATCH 1/5] dt-bindings: mfd: axp20x: Add "self-working" mode for AXP806 Chen-Yu Tsai
2018-06-26 21:41 ` Rob Herring
2018-07-04 7:29 ` Lee Jones
2018-06-20 5:15 ` [PATCH 2/5] mfd: axp20x: Add self-working mode support " Chen-Yu Tsai
2018-07-04 7:33 ` Lee Jones
2018-06-20 5:15 ` [PATCH 3/5] mfd: axp20x: Support AXP806 in I2C mode Chen-Yu Tsai
2018-07-04 7:33 ` Lee Jones
2018-06-20 5:15 ` [PATCH 4/5] arm64: dts: allwinner: h6: Use macros for R_CCU clock and reset indices Chen-Yu Tsai
2018-06-20 13:11 ` Icenowy Zheng
2018-06-20 13:46 ` Chen-Yu Tsai
2018-06-20 5:15 ` [PATCH 5/5] arm64: dts: allwinner: h6: enable AXP805 PMIC on Pine H64 Chen-Yu Tsai
2018-06-26 0:49 ` Icenowy Zheng [this message]
2018-06-26 3:46 ` Chen-Yu Tsai
2018-06-26 5:14 ` [PATCH 0/5] arm64: allwinner: h6: Enable " Icenowy Zheng
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=f93b1524657048279f54004fdbcd6ab5af9ec1c1.camel@aosc.io \
--to=icenowy@aosc.io \
--cc=andre.przywara@arm.com \
--cc=devicetree@vger.kernel.org \
--cc=lee.jones@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=mark.rutland@arm.com \
--cc=maxime.ripard@bootlin.com \
--cc=robh+dt@kernel.org \
--cc=wens@csie.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).