From: Peng Fan <peng.fan@oss.nxp.com>
To: Marco Felsch <m.felsch@pengutronix.de>
Cc: robh+dt@kernel.org, krzysztof.kozlowski+dt@linaro.org,
shawnguo@kernel.org, s.hauer@pengutronix.de,
devicetree@vger.kernel.org, Peng Fan <peng.fan@nxp.com>,
linux-kernel@vger.kernel.org, linux-imx@nxp.com,
kernel@pengutronix.de, festevam@gmail.com,
linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH V2 03/15] arm64: dts: imx8mp-evk: fix BUCK/LDO voltage
Date: Thu, 3 Nov 2022 18:22:42 +0800 [thread overview]
Message-ID: <fbb62cdc-ad27-d2f9-2f5c-ee64f14b103f@oss.nxp.com> (raw)
In-Reply-To: <20221028145306.66lcoycuzmfb5yug@pengutronix.de>
On 10/28/2022 10:53 PM, Marco Felsch wrote:
> On 22-10-24, Peng Fan (OSS) wrote:
>> From: Peng Fan <peng.fan@nxp.com>
>>
>> Per PCA9450C datasheet, the voltage range as below:
>> BUCK1 0.6 - 2.1875
>> BUCK2 0.6 - 2.1875
>> BUCK4 0.6 - 3.4
>> BUCK5 0.6 - 3.4
>> BUCK6 0.6 - 3.4
>>
>> LDO1 1.6-1.9, 3.0-3.3
>> LDO2 0.8 – 1.15
>> LDO3 0.8 - 3.3
>> LDO4 0.8 - 3.3
>> LDO5 1.8 - 3.3
>>
>> Currently we set the board voltage range same as PMIC regulator
>> range.
>
> We did not therefore you aligned it. Also are you sure that this will
> not damage the boards since you're lowering the min-voltage and raising
> the max. voltage? According the schematic, BUCK1 is for VDD_SOC which is
> min. 0.805V and max. 1.0V. After you're change someone could set it to
> 2.1875V. Same applies to BUCK2 which is for VDD_ARM and should be within
> min. 0.805V and max. 1.05V.
You are right. But I think DVFS already limit it.
I am not sure very sure, let me drop this patch for now. I need confirm
with HW team.
Thanks,
Peng.
>
> Regards,
> Marco
>
>> Also add LDO[2,4] in this patch
>>
>> Fixes: 5497bc2a2bff ("arm64: dts: imx8mp-evk: Add PMIC device")
>> Signed-off-by: Peng Fan <peng.fan@nxp.com>
>> ---
>> arch/arm64/boot/dts/freescale/imx8mp-evk.dts | 44 +++++++++++++-------
>> 1 file changed, 30 insertions(+), 14 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-evk.dts b/arch/arm64/boot/dts/freescale/imx8mp-evk.dts
>> index b4c1ef2559f2..a4cddc5a8620 100644
>> --- a/arch/arm64/boot/dts/freescale/imx8mp-evk.dts
>> +++ b/arch/arm64/boot/dts/freescale/imx8mp-evk.dts
>> @@ -248,8 +248,8 @@ pmic@25 {
>> regulators {
>> BUCK1 {
>> regulator-name = "BUCK1";
>> - regulator-min-microvolt = <720000>;
>> - regulator-max-microvolt = <1000000>;
>> + regulator-min-microvolt = <600000>;
>> + regulator-max-microvolt = <2187500>;
>> regulator-boot-on;
>> regulator-always-on;
>> regulator-ramp-delay = <3125>;
>> @@ -257,8 +257,8 @@ BUCK1 {
>>
>> reg_arm: BUCK2 {
>> regulator-name = "BUCK2";
>> - regulator-min-microvolt = <720000>;
>> - regulator-max-microvolt = <1025000>;
>> + regulator-min-microvolt = <600000>;
>> + regulator-max-microvolt = <2187500>;
>> regulator-boot-on;
>> regulator-always-on;
>> regulator-ramp-delay = <3125>;
>> @@ -268,40 +268,56 @@ reg_arm: BUCK2 {
>>
>> BUCK4 {
>> regulator-name = "BUCK4";
>> - regulator-min-microvolt = <3000000>;
>> - regulator-max-microvolt = <3600000>;
>> + regulator-min-microvolt = <600000>;
>> + regulator-max-microvolt = <3400000>;
>> regulator-boot-on;
>> regulator-always-on;
>> };
>>
>> BUCK5 {
>> regulator-name = "BUCK5";
>> - regulator-min-microvolt = <1650000>;
>> - regulator-max-microvolt = <1950000>;
>> + regulator-min-microvolt = <600000>;
>> + regulator-max-microvolt = <3400000>;
>> regulator-boot-on;
>> regulator-always-on;
>> };
>>
>> BUCK6 {
>> regulator-name = "BUCK6";
>> - regulator-min-microvolt = <1045000>;
>> - regulator-max-microvolt = <1155000>;
>> + regulator-min-microvolt = <600000>;
>> + regulator-max-microvolt = <3400000>;
>> regulator-boot-on;
>> regulator-always-on;
>> };
>>
>> LDO1 {
>> regulator-name = "LDO1";
>> - regulator-min-microvolt = <1650000>;
>> - regulator-max-microvolt = <1950000>;
>> + regulator-min-microvolt = <1600000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-boot-on;
>> + regulator-always-on;
>> + };
>> +
>> + LDO2 {
>> + regulator-name = "LDO2";
>> + regulator-min-microvolt = <800000>;
>> + regulator-max-microvolt = <1150000>;
>> regulator-boot-on;
>> regulator-always-on;
>> };
>>
>> LDO3 {
>> regulator-name = "LDO3";
>> - regulator-min-microvolt = <1710000>;
>> - regulator-max-microvolt = <1890000>;
>> + regulator-min-microvolt = <800000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-boot-on;
>> + regulator-always-on;
>> + };
>> +
>> + ldo4: LDO4 {
>> + regulator-name = "LDO4";
>> + regulator-min-microvolt = <800000>;
>> + regulator-max-microvolt = <3300000>;
>> regulator-boot-on;
>> regulator-always-on;
>> };
>> --
>> 2.37.1
>>
>>
>>
next prev parent reply other threads:[~2022-11-03 10:23 UTC|newest]
Thread overview: 32+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-10-24 3:13 [PATCH V2 00/15] arm64: dts: imx8m-evk: misc dts update Peng Fan (OSS)
2022-10-24 3:13 ` [PATCH V2 01/15] arm64: dts: imx8mp: add mlmix power domain Peng Fan (OSS)
2022-10-28 14:58 ` Marco Felsch
2022-10-24 3:13 ` [PATCH V2 02/15] arm64: dts: imx8mp-evk: correct pcie pad settings Peng Fan (OSS)
2022-10-28 14:59 ` Marco Felsch
2022-10-24 3:13 ` [PATCH V2 03/15] arm64: dts: imx8mp-evk: fix BUCK/LDO voltage Peng Fan (OSS)
2022-10-28 14:53 ` Marco Felsch
2022-11-03 10:22 ` Peng Fan [this message]
2022-10-24 3:13 ` [PATCH V2 04/15] ARM64: dts: imx8mp-evk: add pwm support Peng Fan (OSS)
2022-10-28 14:59 ` Marco Felsch
2022-10-24 3:13 ` [PATCH V2 05/15] arm64: dts: imx8mp-evk: enable uart1/3 ports Peng Fan (OSS)
2022-10-28 15:00 ` Marco Felsch
2022-10-24 3:13 ` [PATCH V2 06/15] arm64: dts: imx8mp-evk: enable fspi nor on imx8mp evk Peng Fan (OSS)
2022-10-28 15:00 ` Marco Felsch
2022-10-24 3:13 ` [PATCH V2 07/15] arm64: dts: imx8mp-evk: enable I2C2 node Peng Fan (OSS)
2022-10-28 15:01 ` Marco Felsch
2022-10-24 3:13 ` [PATCH V2 08/15] arm64: dts: imx8mn-evk: update vdd_soc dvs voltage Peng Fan (OSS)
2022-10-24 3:13 ` [PATCH V2 09/15] arm64: dts: imx8mn-evk: set off-on-delay-us in regulator Peng Fan (OSS)
2022-10-28 15:02 ` Marco Felsch
2022-11-03 10:25 ` Peng Fan
2022-10-24 3:13 ` [PATCH V2 10/15] arm64: dts: imx8mn-evk: add i2c gpio recovery settings Peng Fan (OSS)
2022-10-28 14:44 ` Marco Felsch
2022-10-24 3:13 ` [PATCH V2 11/15] arm64: dts: imx8mn-evk: enable uart1 Peng Fan (OSS)
2022-10-28 15:03 ` Marco Felsch
2022-10-24 3:13 ` [PATCH V2 12/15] arm64: dts: imx8mn-evk: enable usdhc1 Peng Fan (OSS)
2022-10-28 15:05 ` Marco Felsch
2022-10-24 3:13 ` [PATCH V2 13/15] arm64: dts: imx8mm-evk: Enable usdhc1 to support wifi Peng Fan (OSS)
2022-10-28 14:42 ` Marco Felsch
2022-11-03 10:27 ` Peng Fan
2022-10-24 3:13 ` [PATCH V2 14/15] arm64: dts: imx8m[m,p]-evk: change to use off-on-delay-us in regulator Peng Fan (OSS)
2022-10-28 14:41 ` [PATCH V2 14/15] arm64: dts: imx8m[m, p]-evk: " Marco Felsch
2022-10-24 3:13 ` [PATCH V2 15/15] arm64: dts: imx8mm-evk: add vcc supply for pca6416 Peng Fan (OSS)
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=fbb62cdc-ad27-d2f9-2f5c-ee64f14b103f@oss.nxp.com \
--to=peng.fan@oss.nxp.com \
--cc=devicetree@vger.kernel.org \
--cc=festevam@gmail.com \
--cc=kernel@pengutronix.de \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-imx@nxp.com \
--cc=linux-kernel@vger.kernel.org \
--cc=m.felsch@pengutronix.de \
--cc=peng.fan@nxp.com \
--cc=robh+dt@kernel.org \
--cc=s.hauer@pengutronix.de \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).