From: sashiko-bot@kernel.org
To: "Adil Hüsrev Tepe" <tadilhusrev@gmail.com>
Cc: devicetree@vger.kernel.org, robh@kernel.org, conor+dt@kernel.org
Subject: Re: [PATCH v2 2/2] iio: proximity: add Imagis ISG5320A SAR sensor driver
Date: Tue, 17 Nov 2026 11:08:13 +0000 [thread overview]
Message-ID: <sashiko-outbox-218694@kernel.org> (raw)
In-Reply-To: <20261117104414.1182364-2-tadilhusrev@gmail.com>
Thank you for your contribution! Sashiko AI review found 4 potential
issues to consider:
- [High] iio: proximity: isg5320a: inverted INT polarity in
isg5320a_reset()
- [Medium] iio: proximity: isg5320a: free_irq() runs before
isg5320a_teardown()
- [Medium] iio: proximity: isg5320a: broken wakeup handling in
isg5320a_events_on()
- [Low] iio: proximity: isg5320a: unchecked enable_irq_wake() in
isg5320a_events_on()
--
commit b880374f416c9c620d39544cb088cc6a533d446b
Author: Adil Hüsrev Tepe <tadilhusrev@gmail.com>
iio: proximity: add Imagis ISG5320A SAR sensor driver
This commit adds an IIO proximity driver for the Imagis ISG5320A I2C
capacitive SAR/grip sensor, exposing a raw proximity channel and
rising/falling threshold events.
> diff --git a/drivers/iio/proximity/isg5320a.c b/drivers/iio/proximity/isg5320a.c
> new file mode 100644
> index 0000000000000..baa8d07ecfd7f
> --- /dev/null
> +++ b/drivers/iio/proximity/isg5320a.c
> @@ -0,0 +1,880 @@
[ ... ]
> +/* Wait for the INT line to reach @level: up to 10 x 5 ms (vendor :262, :281). */
> +static int isg5320a_wait_int(struct isg5320a_data *data, int level)
> +{
> + int cnt, val;
> +
> + if (!data->int_gpio) {
> + msleep(50);
> + return 0;
> + }
> +
> + for (cnt = 0; cnt < 10; cnt++) {
> + /* Logical, not raw: honours the GPIO's DT polarity. */
> + val = gpiod_get_value_cansleep(data->int_gpio);
> + if (val < 0)
> + return val;
> + if (val == level)
> + return cnt;
> + usleep_range(5000, 5100);
> + }
> +
> + return -ETIMEDOUT;
> +}
> +
> +/* vendor isg5320a_reset(), :247-292, plus a CHIPID read the vendor never does */
> +static int isg5320a_reset(struct isg5320a_data *data)
> +{
[ ... ]
> + if (isg5320a_wait_int(data, 1) < 0) /* :262-266 */
> + dev_warn(dev, "INT did not go high before reset\n");
> +
> + ret = regmap_write(data->regmap, ISG5320A_REG_PROTECT, /* :268-271 */
> + ISG5320A_PROTECT_UNLOCK);
> + if (ret)
> + return dev_err_probe(dev, ret, "unlock protect failed\n");
> +
> + ret = regmap_write(data->regmap, ISG5320A_REG_SOFTRESET, /* :273-276 */
> + ISG5320A_SOFTRESET_VAL);
> + if (ret)
> + return dev_err_probe(dev, ret, "soft reset write failed\n");
> +
> + usleep_range(1000, 1100); /* :278 */
> +
> + ret = isg5320a_wait_int(data, 0); /* :280-289 */
> + if (ret < 0)
> + return dev_err_probe(dev, -EIO, "INT not asserted after soft reset\n");
[Severity: High]
Are the @level arguments passed to isg5320a_wait_int() inverted for an
active-low interrupt GPIO?
gpiod_get_value_cansleep() returns the logical state (0 when deasserted,
1 when asserted), whereas the callers here still pass the physical line
levels (1 for released/high before reset, 0 for asserted/low after soft
reset). When int-gpios is described as GPIO_ACTIVE_LOW in Device Tree,
isg5320a_wait_int(data, 0) waits for INT to be deasserted after soft
reset, timing out and failing probe.
Also, dev_err_probe() overwrites ret with -EIO instead of propagating the
error returned by isg5320a_wait_int().
[ ... ]
> +static int isg5320a_events_on(struct isg5320a_data *data)
> +{
[ ... ]
> + WRITE_ONCE(data->ev_enabled, true);
> + enable_irq(data->irq); /* :721 */
> + /* Cache the decision: device_may_wakeup(dev) may change before events_off(). */
> + data->irq_wake_enabled = device_may_wakeup(dev);
> + if (data->irq_wake_enabled)
> + enable_irq_wake(data->irq); /* :722 */
[Severity: Low]
What happens if enable_irq_wake(data->irq) fails here?
data->irq_wake_enabled remains true while desc->wake_depth stays at 0, so
isg5320a_events_off() will later call disable_irq_wake(data->irq) and
trigger an unbalanced IRQ wake disable warning.
[Severity: Medium]
Does arming enable_irq_wake() in isg5320a_events_on() respect changes to
/sys/.../power/wakeup while events are enabled?
If userspace disables wakeup via sysfs after enabling proximity events,
IRQD_WAKEUP_STATE remains set on data->irq and isg5320a_pm_ops has no
system sleep callbacks to stop the sensor, so the interrupt still wakes
the system from suspend. Conversely, on Device Tree systems with
wakeup-source, i2c_device_probe() registers client->irq via
dev_pm_set_wake_irq() (which also makes the device_init_wakeup() call in
isg5320a_probe() redundant), arming the wake IRQ on every suspend even
when data->ev_enabled is false.
Wakeup arming and sensor sleep/resume state across system suspend should
be handled in system sleep PM callbacks instead of isg5320a_events_on()
and isg5320a_events_off().
[ ... ]
> +static void isg5320a_events_off(struct isg5320a_data *data)
> +{
> + struct device *dev = data->dev;
> + int ret = 0;
> +
> + scoped_guard(mutex, &data->lock)
> + ret = regmap_write(data->regmap, ISG5320A_REG_IRQFUNC, /* :726 */
> + ISG5320A_IRQFUNC_DISABLE);
> + if (ret)
> + dev_warn(dev, "IRQFUNC disable failed: %d\n", ret);
> +
> + WRITE_ONCE(data->ev_enabled, false);
> + disable_irq(data->irq); /* :728 */
> + if (data->irq_wake_enabled) {
> + disable_irq_wake(data->irq); /* :729 */
> + data->irq_wake_enabled = false;
> + }
> +}
[ ... ]
> +/* vendor isg5320a_remove(), :2030-2033 */
> +static void isg5320a_teardown(void *arg)
> +{
> + struct isg5320a_data *data = arg;
> + struct device *dev = data->dev;
> +
> + pm_runtime_disable(dev);
> +
> + if (data->ev_enabled) {
> + isg5320a_events_off(data);
> + pm_runtime_put_noidle(dev);
> + }
> +
> + if (!pm_runtime_status_suspended(dev))
> + isg5320a_mode_sleep(data);
> +
> + pm_runtime_set_suspended(dev);
> + pm_runtime_dont_use_autosuspend(dev);
> +}
> +
> +static int isg5320a_probe(struct i2c_client *client)
> +{
[ ... ]
> + ret = devm_add_action_or_reset(dev, isg5320a_teardown, data);
> + if (ret)
> + return ret;
> +
> + if (data->irq > 0) {
> + irqflags = irq_get_trigger_type(data->irq);
> + if (!irqflags)
> + irqflags = IRQF_TRIGGER_FALLING; /* :1932 */
> +
> + ret = devm_request_threaded_irq(dev, data->irq, NULL,
> + isg5320a_irq_thread,
> + irqflags | IRQF_ONESHOT |
> + IRQF_NO_AUTOEN,
> + "isg5320a", indio_dev);
> + if (ret)
> + return dev_err_probe(dev, ret, "irq request failed\n");
> +
> + if (device_property_read_bool(dev, "wakeup-source"))
> + device_init_wakeup(dev, true);
> + }
> +
> + indio_dev->name = "isg5320a";
> + indio_dev->modes = INDIO_DIRECT_MODE;
> + if (data->irq > 0) {
> + indio_dev->info = &isg5320a_info;
> + indio_dev->channels = isg5320a_channels;
> + indio_dev->num_channels = ARRAY_SIZE(isg5320a_channels);
> + } else {
> + indio_dev->info = &isg5320a_info_noirq;
> + indio_dev->channels = isg5320a_channels_noirq;
> + indio_dev->num_channels = ARRAY_SIZE(isg5320a_channels_noirq);
> + }
> +
> + return devm_iio_device_register(dev, indio_dev);
> +}
[Severity: Medium]
Doesn't registering isg5320a_teardown() before devm_request_threaded_irq()
and devm_iio_device_register() cause devres to free data->irq before
isg5320a_teardown() runs?
If the driver is unbound while proximity events are enabled, devres
unregisters indio_dev and calls free_irq(data->irq, indio_dev) while
ISG5320A_REG_IRQFUNC and IRQ wake are still active, and
isg5320a_teardown() -> isg5320a_events_off() then calls disable_irq() and
disable_irq_wake() on an IRQ that has already been shut down and
released.
--
Sashiko AI review · https://sashiko.dev/#/patchset/20261117104414.1182364-1-tadilhusrev@gmail.com?part=2
next prev parent reply other threads:[~2026-11-17 11:08 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-16 7:40 [PATCH v1 0/2] iio: proximity: add Imagis ISG5320A (Samsung Galaxy XCover5) Adil Hüsrev Tepe
2026-11-16 7:40 ` [PATCH v1 1/2] dt-bindings: iio: proximity: add Imagis ISG5320A Adil Hüsrev Tepe
2026-11-16 7:51 ` sashiko-bot
2026-11-16 7:40 ` [PATCH v1 2/2] iio: proximity: add Imagis ISG5320A SAR sensor driver Adil Hüsrev Tepe
2026-11-16 7:58 ` sashiko-bot
2026-11-16 10:53 ` Andy Shevchenko
2026-11-16 10:48 ` [PATCH v1 0/2] iio: proximity: add Imagis ISG5320A (Samsung Galaxy XCover5) Andy Shevchenko
2026-11-17 10:44 ` [PATCH v2 1/2] dt-bindings: iio: proximity: add Imagis ISG5320A Adil Hüsrev Tepe
2026-11-17 10:44 ` [PATCH v2 2/2] iio: proximity: add Imagis ISG5320A SAR sensor driver Adil Hüsrev Tepe
2026-11-17 11:08 ` sashiko-bot [this message]
2026-11-17 10:54 ` [PATCH v2 1/2] dt-bindings: iio: proximity: add Imagis ISG5320A sashiko-bot
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=sashiko-outbox-218694@kernel.org \
--to=sashiko-bot@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=robh@kernel.org \
--cc=sashiko-reviews@lists.linux.dev \
--cc=tadilhusrev@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox