From: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
To: Andrea Parri <andrea.parri@amarulasolutions.com>
Cc: linux-kernel@vger.kernel.org, linux-doc@vger.kernel.org,
Josh Triplett <josh@joshtriplett.org>,
Steven Rostedt <rostedt@goodmis.org>,
Mathieu Desnoyers <mathieu.desnoyers@efficios.com>,
Lai Jiangshan <jiangshanlai@gmail.com>,
Jonathan Corbet <corbet@lwn.net>
Subject: Re: [PATCH] doc: Update synchronize_rcu() definition in whatisRCU.txt
Date: Fri, 8 Jun 2018 02:38:26 -0700 [thread overview]
Message-ID: <20180608093826.GT3593@linux.vnet.ibm.com> (raw)
In-Reply-To: <1528365717-7213-1-git-send-email-andrea.parri@amarulasolutions.com>
On Thu, Jun 07, 2018 at 12:01:57PM +0200, Andrea Parri wrote:
> The synchronize_rcu() definition based on RW-locks in whatisRCU.txt
> does not meet the "Memory-Barrier Guarantees" in Requirements.html;
> for example, the following SB-like test:
>
> P0: P1:
>
> WRITE_ONCE(x, 1); WRITE_ONCE(y, 1);
> synchronize_rcu(); smp_mb();
> r0 = READ_ONCE(y); r1 = READ_ONCE(x);
>
> should not be allowed to reach the state "r0 = 0 AND r1 = 0", but
> the current write_lock()+write_unlock() definition can not ensure
> this. Remedies this by inserting an smp_mb__after_spinlock().
>
> Suggested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
> Signed-off-by: Andrea Parri <andrea.parri@amarulasolutions.com>
Queued for review, thank you!
Thanx, Paul
> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
> Cc: Josh Triplett <josh@joshtriplett.org>
> Cc: Steven Rostedt <rostedt@goodmis.org>
> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
> Cc: Lai Jiangshan <jiangshanlai@gmail.com>
> Cc: Jonathan Corbet <corbet@lwn.net>
> ---
> Documentation/RCU/whatisRCU.txt | 16 ++++++++++------
> 1 file changed, 10 insertions(+), 6 deletions(-)
>
> diff --git a/Documentation/RCU/whatisRCU.txt b/Documentation/RCU/whatisRCU.txt
> index a27fbfb0efb82..86a54ff911fc2 100644
> --- a/Documentation/RCU/whatisRCU.txt
> +++ b/Documentation/RCU/whatisRCU.txt
> @@ -586,6 +586,7 @@ It is extremely simple:
> void synchronize_rcu(void)
> {
> write_lock(&rcu_gp_mutex);
> + smp_mb__after_spinlock();
> write_unlock(&rcu_gp_mutex);
> }
>
> @@ -607,12 +608,15 @@ don't forget about them when submitting patches making use of RCU!]
>
> The rcu_read_lock() and rcu_read_unlock() primitive read-acquire
> and release a global reader-writer lock. The synchronize_rcu()
> -primitive write-acquires this same lock, then immediately releases
> -it. This means that once synchronize_rcu() exits, all RCU read-side
> -critical sections that were in progress before synchronize_rcu() was
> -called are guaranteed to have completed -- there is no way that
> -synchronize_rcu() would have been able to write-acquire the lock
> -otherwise.
> +primitive write-acquires this same lock, then releases it. This means
> +that once synchronize_rcu() exits, all RCU read-side critical sections
> +that were in progress before synchronize_rcu() was called are guaranteed
> +to have completed -- there is no way that synchronize_rcu() would have
> +been able to write-acquire the lock otherwise. The smp_mb__after_spinlock()
> +promotes synchronize_rcu() to a full memory barrier in compliance with
> +the "Memory-Barrier Guarantees" listed in:
> +
> + Documentation/RCU/Design/Requirements/Requirements.html.
>
> It is possible to nest rcu_read_lock(), since reader-writer locks may
> be recursively acquired. Note also that rcu_read_lock() is immune
> --
> 2.7.4
>
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
prev parent reply other threads:[~2018-06-08 9:36 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-06-07 10:01 [PATCH] doc: Update synchronize_rcu() definition in whatisRCU.txt Andrea Parri
2018-06-08 9:38 ` Paul E. McKenney [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180608093826.GT3593@linux.vnet.ibm.com \
--to=paulmck@linux.vnet.ibm.com \
--cc=andrea.parri@amarulasolutions.com \
--cc=corbet@lwn.net \
--cc=jiangshanlai@gmail.com \
--cc=josh@joshtriplett.org \
--cc=linux-doc@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mathieu.desnoyers@efficios.com \
--cc=rostedt@goodmis.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).