Re: [PATCH v3 1/3] dt-bindings: iio: adc: add AD7191

[Rob Herring <robh@kernel.org>]

On Wed, Jan 29, 2025 at 04:29:02PM +0200, Alisa-Dariana Roman wrote:
> AD7191 is a pin-programmable, ultra-low noise 24-bit sigma-delta ADC
> designed for precision bridge sensor measurements. It features two
> differential analog input channels, selectable output rates,
> programmable gain, internal temperature sensor and simultaneous
> 50Hz/60Hz rejection.
> 
> Signed-off-by: Alisa-Dariana Roman <alisa.roman@analog.com>
> ---
>  .../bindings/iio/adc/adi,ad7191.yaml          | 149 ++++++++++++++++++
>  MAINTAINERS                                   |   7 +
>  2 files changed, 156 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/iio/adc/adi,ad7191.yaml
> 
> diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7191.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7191.yaml
> new file mode 100644
> index 000000000000..ac14096ba76c
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7191.yaml
> @@ -0,0 +1,149 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +# Copyright 2025 Analog Devices Inc.
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/iio/adc/adi,ad7191.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Analog Devices AD7191 ADC
> +
> +maintainers:
> +  - Alisa-Dariana Roman <alisa.roman@analog.com>
> +
> +description: |
> +  Bindings for the Analog Devices AD7191 ADC device. Datasheet can be
> +  found here:
> +  https://www.analog.com/media/en/technical-documentation/data-sheets/AD7191.pdf
> +  The device's PDOWN pin must be connected to the SPI controller's chip select
> +  pin.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - adi,ad7191
> +
> +  reg:
> +    maxItems: 1
> +
> +  spi-cpol: true
> +
> +  spi-cpha: true
> +
> +  clocks:
> +    maxItems: 1
> +    description: |

Don't need '|' if no formatting.

> +      Must be present when CLKSEL pin is tied HIGH to select external clock
> +      source (either a crystal between MCLK1 and MCLK2 pins, or a
> +      CMOS-compatible clock driving MCLK2 pin). Must be absent when CLKSEL pin
> +      is tied LOW to use the internal 4.92MHz clock.
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  avdd-supply:
> +    description: AVdd voltage supply
> +
> +  dvdd-supply:
> +    description: DVdd voltage supply
> +
> +  vref-supply:
> +    description: Vref voltage supply
> +
> +  odr-gpios:
> +    description: |

Don't need '|' if no formatting.

> +      ODR1 and ODR2 pins for output data rate selection. Should be defined if
> +      adi,odr-value is absent.
> +    minItems: 2
> +    maxItems: 2
> +
> +  adi,odr-value:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    description: |
> +      Should be present if ODR pins are pin-strapped. Possible values:
> +      120 Hz (ODR1=0, ODR2=0)
> +      60 Hz (ODR1=0, ODR2=1)
> +      50 Hz (ODR1=1, ODR2=0)
> +      10 Hz (ODR1=1, ODR2=1)
> +      If defined, odr-gpios must be absent.
> +    enum: [120, 60, 50, 10]
> +
> +  pga-gpios:
> +    description: |

Don't need '|' if no formatting.

With those fixed,

Reviewed-by: Rob Herring (Arm) <robh@kernel.org>

> +      PGA1 and PGA2 pins for gain selection. Should be defined if adi,pga-value
> +      is absent.
> +    minItems: 2
> +    maxItems: 2