From: Stoyan Bogdanov <sbogdanov@baylibre.com>
To: jbrunet@baylibre.com, linux@roeck-us.net, robh@kernel.org,
krzk+dt@kernel.org, conor+dt@kernel.org, corbet@lwn.net,
skhan@linuxfoundation.org
Cc: linux-hwmon@vger.kernel.org, devicetree@vger.kernel.org,
linux-doc@vger.kernel.org, linux-kernel@vger.kernel.org,
Stoyan Bogdanov <sbogdanov@baylibre.com>
Subject: [PATCH v1 3/3] hwmon: (pmbus/tps1689): Add TPS1689 support
Date: Thu, 12 Feb 2026 10:45:02 +0200 [thread overview]
Message-ID: <20260212084502.1795-4-sbogdanov@baylibre.com> (raw)
In-Reply-To: <20260212084502.1795-1-sbogdanov@baylibre.com>
Extend tps25990 existing driver to support tps1689 eFuse,
since they are sharing command interface and functionality
Update documentation for tps1689
Signed-off-by: Stoyan Bogdanov <sbogdanov@baylibre.com>
---
Documentation/hwmon/tps25990.rst | 15 ++++---
drivers/hwmon/pmbus/tps25990.c | 70 ++++++++++++++++++++++++++++++++
2 files changed, 80 insertions(+), 5 deletions(-)
diff --git a/Documentation/hwmon/tps25990.rst b/Documentation/hwmon/tps25990.rst
index 04faec780d26..e8bc9a550bda 100644
--- a/Documentation/hwmon/tps25990.rst
+++ b/Documentation/hwmon/tps25990.rst
@@ -9,26 +9,31 @@ Supported chips:
Prefix: 'tps25990'
- * Datasheet
+ Datasheet: Publicly available at Texas Instruments website: https://www.ti.com/lit/gpn/tps25990
- Publicly available at Texas Instruments website: https://www.ti.com/lit/gpn/tps25990
+ * TI TPS1689
+
+ Prefix: 'tps1689'
+
+ Datasheet: Publicly available at Texas Instruments website: https://www.ti.com/lit/gpn/tps1689
Author:
Jerome Brunet <jbrunet@baylibre.com>
+ Stoyan Bogdanov <sbogdanov@baylibre.com>
Description
-----------
-This driver implements support for TI TPS25990 eFuse.
+This driver implements support for TI TPS25990 and TI TPS1689 eFuse chips.
This is an integrated, high-current circuit protection and power
management device with PMBUS interface
-Device compliant with:
+Devices are compliant with:
- PMBus rev 1.3 interface.
-Device supports direct format for reading input voltages,
+Devices supports direct format for reading input voltages,
output voltage, input current, input power and temperature.
Due to the specificities of the chip, all history reset attributes
diff --git a/drivers/hwmon/pmbus/tps25990.c b/drivers/hwmon/pmbus/tps25990.c
index 268e361b6fd3..3d4056724303 100644
--- a/drivers/hwmon/pmbus/tps25990.c
+++ b/drivers/hwmon/pmbus/tps25990.c
@@ -370,6 +370,15 @@ static const struct regulator_desc tps25990_reg_desc[] = {
};
#endif
+struct local_direct_value tps1689_local_info = {
+ .m[TPS25990_VIN_OVF] = 3984,
+ .b[TPS25990_VIN_OVF] = -63750,
+ .R[TPS25990_VIN_OVF] = -3,
+ .m[TPS25990_IIN_OCF] = 7111,
+ .b[TPS25990_IIN_OCF] = -2133,
+ .R[TPS25990_IIN_OCF] = -2,
+};
+
struct local_direct_value tps25590_local_info = {
.m[TPS25990_VIN_OVF] = 10163,
.b[TPS25990_VIN_OVF] = -30081,
@@ -379,6 +388,60 @@ struct local_direct_value tps25590_local_info = {
.R[TPS25990_IIN_OCF] = -6,
};
+static struct pmbus_driver_info tps1689_base_info = {
+ .pages = 1,
+ .format[PSC_VOLTAGE_IN] = direct,
+ .m[PSC_VOLTAGE_IN] = 1166,
+ .b[PSC_VOLTAGE_IN] = 0,
+ .R[PSC_VOLTAGE_IN] = -2,
+ .format[PSC_VOLTAGE_OUT] = direct,
+ .m[PSC_VOLTAGE_OUT] = 1166,
+ .b[PSC_VOLTAGE_OUT] = 0,
+ .R[PSC_VOLTAGE_OUT] = -2,
+ .format[PSC_TEMPERATURE] = direct,
+ .m[PSC_TEMPERATURE] = 140,
+ .b[PSC_TEMPERATURE] = 32103,
+ .R[PSC_TEMPERATURE] = -2,
+ /*
+ * Current and Power measurement depends on the ohm value
+ * of Rimon. m is multiplied by 1000 below to have an integer
+ * and -3 is added to R to compensate.
+ */
+ .format[PSC_CURRENT_IN] = direct,
+ .m[PSC_CURRENT_IN] = 9548,
+ .b[PSC_CURRENT_IN] = 0,
+ .R[PSC_CURRENT_IN] = -6,
+ .format[PSC_CURRENT_OUT] = direct,
+ .m[PSC_CURRENT_OUT] = 24347,
+ .b[PSC_CURRENT_OUT] = 0,
+ .R[PSC_CURRENT_OUT] = -3,
+ .format[PSC_POWER] = direct,
+ .m[PSC_POWER] = 2775,
+ .b[PSC_POWER] = 0,
+ .R[PSC_POWER] = -4,
+ .func[0] = (PMBUS_HAVE_VIN |
+ PMBUS_HAVE_VOUT |
+ PMBUS_HAVE_VMON |
+ PMBUS_HAVE_IIN |
+ PMBUS_HAVE_PIN |
+ PMBUS_HAVE_TEMP |
+ PMBUS_HAVE_STATUS_VOUT |
+ PMBUS_HAVE_STATUS_IOUT |
+ PMBUS_HAVE_STATUS_INPUT |
+ PMBUS_HAVE_STATUS_TEMP |
+ PMBUS_HAVE_SAMPLES),
+
+ .read_word_data = tps25990_read_word_data,
+ .write_word_data = tps25990_write_word_data,
+ .read_byte_data = tps25990_read_byte_data,
+ .write_byte_data = tps25990_write_byte_data,
+
+#if IS_ENABLED(CONFIG_SENSORS_TPS25990_REGULATOR)
+ .reg_desc = tps25990_reg_desc,
+ .num_regulators = ARRAY_SIZE(tps25990_reg_desc),
+#endif
+};
+
static struct pmbus_driver_info tps25990_base_info = {
.pages = 1,
.format[PSC_VOLTAGE_IN] = direct,
@@ -428,18 +491,25 @@ static struct pmbus_driver_info tps25990_base_info = {
#endif
};
+struct tps25990_data data_tps1689 = {
+ .info = &tps1689_base_info,
+ .info_local = &tps1689_local_info,
+};
+
struct tps25990_data data_tps25990 = {
.info = &tps25990_base_info,
.info_local = &tps25590_local_info,
};
static const struct i2c_device_id tps25990_i2c_id[] = {
+ { .name = "tps1689", .driver_data = (kernel_ulong_t)&data_tps1689 },
{ .name = "tps25990", .driver_data = (kernel_ulong_t)&data_tps25990 },
{}
};
MODULE_DEVICE_TABLE(i2c, tps25990_i2c_id);
static const struct of_device_id tps25990_of_match[] = {
+ { .compatible = "ti,tps1689", .data = &data_tps1689 },
{ .compatible = "ti,tps25990", .data = &data_tps25990 },
{}
};
--
2.34.1
prev parent reply other threads:[~2026-02-12 8:45 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-02-12 8:44 [PATCH v1 0/3] Add TI TPS1689 pmbus eFuse Stoyan Bogdanov
2026-02-12 8:45 ` [PATCH v1 1/3] hwmon: (pmbus/tps25990): Rework TPS25990 non standatd direct conversion Stoyan Bogdanov
2026-02-12 14:03 ` kernel test robot
2026-02-12 14:55 ` kernel test robot
2026-02-12 8:45 ` [PATCH v1 2/3] dt-bindings: hwmon: pmbus/tps1689: Add TPS1689 support Stoyan Bogdanov
2026-02-12 12:06 ` Krzysztof Kozlowski
2026-02-12 8:45 ` Stoyan Bogdanov [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260212084502.1795-4-sbogdanov@baylibre.com \
--to=sbogdanov@baylibre.com \
--cc=conor+dt@kernel.org \
--cc=corbet@lwn.net \
--cc=devicetree@vger.kernel.org \
--cc=jbrunet@baylibre.com \
--cc=krzk+dt@kernel.org \
--cc=linux-doc@vger.kernel.org \
--cc=linux-hwmon@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@roeck-us.net \
--cc=robh@kernel.org \
--cc=skhan@linuxfoundation.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox