* [PATCH v10 1/6] Docs: iio: ad4030: Add double PWM SPI offload doc
2026-02-23 17:08 [PATCH v10 0/6] Add SPI offload support to AD4030 Marcelo Schmitt
@ 2026-02-23 17:09 ` Marcelo Schmitt
2026-02-23 17:09 ` [PATCH v10 2/6] dt-bindings: iio: adc: adi,ad4030: Add PWM Marcelo Schmitt
` (5 subsequent siblings)
6 siblings, 0 replies; 8+ messages in thread
From: Marcelo Schmitt @ 2026-02-23 17:09 UTC (permalink / raw)
To: linux-iio, devicetree, linux-doc, linux-kernel
Cc: jic23, michael.hennerich, nuno.sa, eblanc, dlechner, andy, robh,
krzk+dt, conor+dt, corbet, marcelo.schmitt1
Document double PWM setup SPI offload wiring schema.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
---
Change log v9 -> v10
- No changes.
Documentation/iio/ad4030.rst | 39 ++++++++++++++++++++++++++++++++++++
1 file changed, 39 insertions(+)
diff --git a/Documentation/iio/ad4030.rst b/Documentation/iio/ad4030.rst
index b57424b650a8..9caafa4148b0 100644
--- a/Documentation/iio/ad4030.rst
+++ b/Documentation/iio/ad4030.rst
@@ -92,6 +92,45 @@ Interleaved mode
In this mode, both channels conversion results are bit interleaved one SDO line.
As such the wiring is the same as `One lane mode`_.
+SPI offload wiring
+^^^^^^^^^^^^^^^^^^
+
+.. code-block::
+
+ +-------------+ +-------------+
+ | CNV |<-----+--| GPIO |
+ | | +--| PWM0 |
+ | | | |
+ | | +--| PWM1 |
+ | | | +-------------+
+ | | +->| TRIGGER |
+ | CS |<--------| CS |
+ | | | |
+ | ADC | | SPI |
+ | | | |
+ | SDI |<--------| SDO |
+ | SDO |-------->| SDI |
+ | SCLK |<--------| SCLK |
+ +-------------+ +-------------+
+
+In this mode, both the ``cnv-gpios`` and a ``pwms`` properties are required.
+The ``pwms`` property specifies the PWM that is connected to the ADC CNV pin.
+The SPI offload will have a ``trigger-sources`` property to indicate the SPI
+offload (PWM) trigger source. For AD4030 and similar ADCs, there are two
+possible data transfer zones for sample N. One of them (zone 1) starts after the
+data conversion for sample N is complete while the other one (zone 2) starts 9.8
+nanoseconds after the rising edge of CNV for sample N + 1.
+
+The configuration depicted in the above diagram is intended to perform data
+transfer in zone 2. To achieve high sample rates while meeting ADC timing
+requirements, an offset is added between the rising edges of PWM0 and PWM1 to
+delay the SPI transfer until 9.8 nanoseconds after CNV rising edge. This
+requires a specialized PWM controller that can provide such an offset.
+The `AD4630-FMC HDL project`_, for example, can be configured to sample AD4030
+data during zone 2 data read window.
+
+.. _AD4630-FMC HDL project: https://analogdevicesinc.github.io/hdl/projects/ad4630_fmc/index.html
+
SPI Clock mode
--------------
--
2.39.2
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH v10 2/6] dt-bindings: iio: adc: adi,ad4030: Add PWM
2026-02-23 17:08 [PATCH v10 0/6] Add SPI offload support to AD4030 Marcelo Schmitt
2026-02-23 17:09 ` [PATCH v10 1/6] Docs: iio: ad4030: Add double PWM SPI offload doc Marcelo Schmitt
@ 2026-02-23 17:09 ` Marcelo Schmitt
2026-02-23 17:09 ` [PATCH v10 3/6] iio: adc: ad4030: Add SPI offload support Marcelo Schmitt
` (4 subsequent siblings)
6 siblings, 0 replies; 8+ messages in thread
From: Marcelo Schmitt @ 2026-02-23 17:09 UTC (permalink / raw)
To: linux-iio, devicetree, linux-doc, linux-kernel
Cc: jic23, michael.hennerich, nuno.sa, eblanc, dlechner, andy, robh,
krzk+dt, conor+dt, corbet, marcelo.schmitt1, Conor Dooley
In setups designed for high speed data rate capture, a PWM is used to
generate the CNV signal that issues data captures from the ADC. Document
the use of a PWM for AD4030 and similar devices.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
---
Change log v9 -> v10
- No changes.
Documentation/devicetree/bindings/iio/adc/adi,ad4030.yaml | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad4030.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad4030.yaml
index 29e266865805..a135c66142df 100644
--- a/Documentation/devicetree/bindings/iio/adc/adi,ad4030.yaml
+++ b/Documentation/devicetree/bindings/iio/adc/adi,ad4030.yaml
@@ -72,6 +72,10 @@ properties:
The Reset Input (/RST). Used for asynchronous device reset.
maxItems: 1
+ pwms:
+ description: PWM signal connected to the CNV pin.
+ maxItems: 1
+
interrupts:
description:
The BUSY pin is used to signal that the conversions results are available
--
2.39.2
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH v10 3/6] iio: adc: ad4030: Add SPI offload support
2026-02-23 17:08 [PATCH v10 0/6] Add SPI offload support to AD4030 Marcelo Schmitt
2026-02-23 17:09 ` [PATCH v10 1/6] Docs: iio: ad4030: Add double PWM SPI offload doc Marcelo Schmitt
2026-02-23 17:09 ` [PATCH v10 2/6] dt-bindings: iio: adc: adi,ad4030: Add PWM Marcelo Schmitt
@ 2026-02-23 17:09 ` Marcelo Schmitt
2026-02-23 17:10 ` [PATCH v10 4/6] dt-bindings: iio: adc: adi,ad4030: Add ADAQ4216 and ADAQ4224 Marcelo Schmitt
` (3 subsequent siblings)
6 siblings, 0 replies; 8+ messages in thread
From: Marcelo Schmitt @ 2026-02-23 17:09 UTC (permalink / raw)
To: linux-iio, devicetree, linux-doc, linux-kernel
Cc: jic23, michael.hennerich, nuno.sa, eblanc, dlechner, andy, robh,
krzk+dt, conor+dt, corbet, marcelo.schmitt1, Trevor Gamblin,
Axel Haslam
AD4030 and similar ADCs can capture data at sample rates up to 2 mega
samples per second (MSPS). Not all SPI controllers are able to achieve such
high throughputs and even when the controller is fast enough to run
transfers at the required speed, it may be costly to the CPU to handle
transfer data at such high sample rates. Add SPI offload support for AD4030
and similar ADCs to enable data capture at maximum sample rates.
Note that a pair of PWM devices are used for the supported setup. One of
the PWM goes to the ADC CNV pin to initiate conversions while the other PWM
is connected to the SPI offload trigger to signal when to fetch data from
the peripheral. Note also that the PWMs must be somewhat synchronized such
to make the controller run transfers only when ADC sample data is
available. See Documentation/iio/ad4030.rst for details.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Co-developed-by: Trevor Gamblin <tgamblin@baylibre.com>
Signed-off-by: Trevor Gamblin <tgamblin@baylibre.com>
Co-developed-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
---
Change log v9 -> v10
- Explained the need of PWM in commint message.
- Fixed off-by-one bug.
- Initialize iio_scan_type struct fields on same order they are on structure definition.
drivers/iio/adc/Kconfig | 5 +
drivers/iio/adc/ad4030.c | 409 +++++++++++++++++++++++++++++++++++++--
2 files changed, 396 insertions(+), 18 deletions(-)
diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
index 60038ae8dfc4..c1e55bc70ff4 100644
--- a/drivers/iio/adc/Kconfig
+++ b/drivers/iio/adc/Kconfig
@@ -60,9 +60,14 @@ config AD4030
tristate "Analog Devices AD4030 ADC Driver"
depends on SPI
depends on GPIOLIB
+ depends on PWM
select REGMAP
select IIO_BUFFER
+ select IIO_BUFFER_DMA
+ select IIO_BUFFER_DMAENGINE
select IIO_TRIGGERED_BUFFER
+ select SPI_OFFLOAD
+ select SPI_OFFLOAD_TRIGGER_PWM
help
Say yes here to build support for Analog Devices AD4030 and AD4630 high speed
SPI analog to digital converters (ADC).
diff --git a/drivers/iio/adc/ad4030.c b/drivers/iio/adc/ad4030.c
index def3e1d01ceb..9540ff8c49df 100644
--- a/drivers/iio/adc/ad4030.c
+++ b/drivers/iio/adc/ad4030.c
@@ -14,15 +14,26 @@
*/
#include <linux/bitfield.h>
+#include <linux/cleanup.h>
#include <linux/clk.h>
-#include <linux/iio/iio.h>
-#include <linux/iio/trigger_consumer.h>
-#include <linux/iio/triggered_buffer.h>
+#include <linux/dmaengine.h>
+#include <linux/limits.h>
+#include <linux/log2.h>
+#include <linux/math64.h>
+#include <linux/minmax.h>
+#include <linux/pwm.h>
#include <linux/regmap.h>
#include <linux/regulator/consumer.h>
+#include <linux/spi/offload/consumer.h>
#include <linux/spi/spi.h>
#include <linux/unaligned.h>
#include <linux/units.h>
+#include <linux/types.h>
+
+#include <linux/iio/buffer-dmaengine.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/trigger_consumer.h>
+#include <linux/iio/triggered_buffer.h>
#define AD4030_REG_INTERFACE_CONFIG_A 0x00
#define AD4030_REG_INTERFACE_CONFIG_A_SW_RESET (BIT(0) | BIT(7))
@@ -111,6 +122,8 @@
#define AD4632_TCYC_NS 2000
#define AD4632_TCYC_ADJUSTED_NS (AD4632_TCYC_NS - AD4030_TCNVL_NS)
#define AD4030_TRESET_COM_DELAY_MS 750
+/* Datasheet says 9.8ns, so use the closest integer value */
+#define AD4030_TQUIET_CNV_DELAY_NS 10
enum ad4030_out_mode {
AD4030_OUT_DATA_MD_DIFF,
@@ -136,11 +149,13 @@ struct ad4030_chip_info {
const char *name;
const unsigned long *available_masks;
const struct iio_chan_spec channels[AD4030_MAX_IIO_CHANNEL_NB];
+ const struct iio_chan_spec offload_channels[AD4030_MAX_IIO_CHANNEL_NB];
u8 grade;
u8 precision_bits;
/* Number of hardware channels */
int num_voltage_inputs;
unsigned int tcyc_ns;
+ unsigned int max_sample_rate_hz;
};
struct ad4030_state {
@@ -153,6 +168,14 @@ struct ad4030_state {
int offset_avail[3];
unsigned int avg_log2;
enum ad4030_out_mode mode;
+ /* Offload sampling */
+ struct spi_transfer offload_xfer;
+ struct spi_message offload_msg;
+ struct spi_offload *offload;
+ struct spi_offload_trigger *offload_trigger;
+ struct spi_offload_trigger_config offload_trigger_config;
+ struct pwm_device *cnv_trigger;
+ struct pwm_waveform cnv_wf;
/*
* DMA (thus cache coherency maintenance) requires the transfer buffers
@@ -209,8 +232,9 @@ struct ad4030_state {
* - voltage0-voltage1
* - voltage2-voltage3
*/
-#define AD4030_CHAN_DIFF(_idx, _scan_type) { \
+#define __AD4030_CHAN_DIFF(_idx, _scan_type, _offload) { \
.info_mask_shared_by_all = \
+ (_offload ? BIT(IIO_CHAN_INFO_SAMP_FREQ) : 0) | \
BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO), \
.info_mask_shared_by_all_available = \
BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO), \
@@ -232,6 +256,12 @@ struct ad4030_state {
.num_ext_scan_type = ARRAY_SIZE(_scan_type), \
}
+#define AD4030_CHAN_DIFF(_idx, _scan_type) \
+ __AD4030_CHAN_DIFF(_idx, _scan_type, 0)
+
+#define AD4030_OFFLOAD_CHAN_DIFF(_idx, _scan_type) \
+ __AD4030_CHAN_DIFF(_idx, _scan_type, 1)
+
/*
* AD4030 can average over 2^N samples, where N = 1, 2, 3, ..., 16.
* We use N = 0 to mean no sample averaging.
@@ -244,6 +274,11 @@ static const int ad4030_average_modes[] = {
BIT(13), BIT(14), BIT(15), BIT(16),
};
+static const struct spi_offload_config ad4030_offload_config = {
+ .capability_flags = SPI_OFFLOAD_CAP_TRIGGER |
+ SPI_OFFLOAD_CAP_RX_STREAM_DMA,
+};
+
static int ad4030_enter_config_mode(struct ad4030_state *st)
{
st->tx_data[0] = AD4030_REG_ACCESS;
@@ -457,6 +492,102 @@ static int ad4030_get_chan_calibbias(struct iio_dev *indio_dev,
}
}
+static void ad4030_get_sampling_freq(struct ad4030_state *st, int *freq)
+{
+ struct spi_offload_trigger_config *config = &st->offload_trigger_config;
+
+ /*
+ * Conversion data is fetched from the device when the offload transfer
+ * is triggered. Thus, provide the SPI offload trigger frequency as the
+ * sampling frequency.
+ */
+ *freq = config->periodic.frequency_hz;
+}
+
+static int ad4030_update_conversion_rate(struct ad4030_state *st,
+ unsigned int freq_hz, unsigned int avg_log2)
+{
+ struct spi_offload_trigger_config *config = &st->offload_trigger_config;
+ unsigned int offload_period_ns, cnv_rate_hz;
+ struct pwm_waveform cnv_wf = { };
+ u64 target = AD4030_TCNVH_NS;
+ u64 offload_offset_ns;
+ int ret;
+
+ /*
+ * When averaging/oversampling over N samples, we fire the offload
+ * trigger once at every N pulses of the CNV signal. Conversely, the CNV
+ * signal needs to be N times faster than the offload trigger. Take that
+ * into account to correctly re-evaluate both the PWM waveform connected
+ * to CNV and the SPI offload trigger.
+ */
+ cnv_rate_hz = freq_hz << avg_log2;
+
+ cnv_wf.period_length_ns = DIV_ROUND_CLOSEST(NSEC_PER_SEC, cnv_rate_hz);
+ /*
+ * The datasheet lists a minimum time of 9.8 ns, but no maximum. If the
+ * rounded PWM's value is less than 10, increase the target value by 10
+ * and attempt to round the waveform again, until the value is at least
+ * 10 ns. Use a separate variable to represent the target in case the
+ * rounding is severe enough to keep putting the first few results under
+ * the minimum 10ns condition checked by the while loop.
+ */
+ do {
+ cnv_wf.duty_length_ns = target;
+ ret = pwm_round_waveform_might_sleep(st->cnv_trigger, &cnv_wf);
+ if (ret)
+ return ret;
+ target += AD4030_TCNVH_NS;
+ } while (cnv_wf.duty_length_ns < AD4030_TCNVH_NS);
+
+ /*
+ * The CNV waveform period (period_length_ns) might get rounded down by
+ * pwm_round_waveform_might_sleep(). Check the resultant PWM period
+ * is not smaller than the minimum data conversion cycle time.
+ */
+ if (!in_range(cnv_wf.period_length_ns, AD4030_TCYC_NS, INT_MAX))
+ return -EINVAL;
+
+ offload_period_ns = DIV_ROUND_CLOSEST(NSEC_PER_SEC, freq_hz);
+
+ config->periodic.frequency_hz = DIV_ROUND_UP(HZ_PER_GHZ, offload_period_ns);
+
+ /*
+ * The hardware does the capture on zone 2 (when SPI trigger PWM
+ * is used). This means that the SPI trigger signal should happen at
+ * tsync + tquiet_con_delay being tsync the conversion signal period
+ * and tquiet_con_delay 9.8ns. Hence set the PWM phase accordingly.
+ *
+ * The PWM waveform API only supports nanosecond resolution right now,
+ * so round this setting to the closest available value.
+ */
+ offload_offset_ns = AD4030_TQUIET_CNV_DELAY_NS;
+ do {
+ config->periodic.offset_ns = offload_offset_ns;
+ ret = spi_offload_trigger_validate(st->offload_trigger, config);
+ if (ret)
+ return ret;
+ offload_offset_ns += AD4030_TQUIET_CNV_DELAY_NS;
+ } while (config->periodic.offset_ns < AD4030_TQUIET_CNV_DELAY_NS);
+
+ st->cnv_wf = cnv_wf;
+
+ return 0;
+}
+
+static int ad4030_set_sampling_freq(struct iio_dev *indio_dev, int freq_hz)
+{
+ struct ad4030_state *st = iio_priv(indio_dev);
+
+ if (freq_hz == 0)
+ return -EINVAL;
+
+ if (!in_range(freq_hz, 0, st->chip->max_sample_rate_hz))
+ return -ERANGE;
+
+ return ad4030_update_conversion_rate(st, freq_hz, st->avg_log2);
+}
+
static int ad4030_set_chan_calibscale(struct iio_dev *indio_dev,
struct iio_chan_spec const *chan,
int gain_int,
@@ -516,11 +647,30 @@ static int ad4030_set_avg_frame_len(struct iio_dev *dev, int avg_val)
struct ad4030_state *st = iio_priv(dev);
unsigned int avg_log2 = ilog2(avg_val);
unsigned int last_avg_idx = ARRAY_SIZE(ad4030_average_modes) - 1;
+ int freq_hz;
int ret;
if (avg_val < 0 || avg_val > ad4030_average_modes[last_avg_idx])
return -EINVAL;
+ if (st->offload_trigger) {
+ /*
+ * The sample averaging and sampling frequency configurations
+ * are mutually dependent on each other. That's because the
+ * effective data sample rate is fCNV / 2^N, where N is the
+ * number of samples being averaged.
+ *
+ * When SPI offload is supported and we have control over the
+ * sample rate, the conversion start signal (CNV) and the SPI
+ * offload trigger frequencies must be re-evaluated so data is
+ * fetched only after 'avg_val' conversions.
+ */
+ ad4030_get_sampling_freq(st, &freq_hz);
+ ret = ad4030_update_conversion_rate(st, freq_hz, avg_log2);
+ if (ret)
+ return ret;
+ }
+
ret = regmap_write(st->regmap, AD4030_REG_AVG,
AD4030_REG_AVG_MASK_AVG_SYNC |
FIELD_PREP(AD4030_REG_AVG_MASK_AVG_VAL, avg_log2));
@@ -773,6 +923,10 @@ static int ad4030_read_raw_dispatch(struct iio_dev *indio_dev,
*val = BIT(st->avg_log2);
return IIO_VAL_INT;
+ case IIO_CHAN_INFO_SAMP_FREQ:
+ ad4030_get_sampling_freq(st, val);
+ return IIO_VAL_INT;
+
default:
return -EINVAL;
}
@@ -813,6 +967,9 @@ static int ad4030_write_raw_dispatch(struct iio_dev *indio_dev,
case IIO_CHAN_INFO_OVERSAMPLING_RATIO:
return ad4030_set_avg_frame_len(indio_dev, val);
+ case IIO_CHAN_INFO_SAMP_FREQ:
+ return ad4030_set_sampling_freq(indio_dev, val);
+
default:
return -EINVAL;
}
@@ -902,6 +1059,86 @@ static const struct iio_buffer_setup_ops ad4030_buffer_setup_ops = {
.validate_scan_mask = ad4030_validate_scan_mask,
};
+static void ad4030_prepare_offload_msg(struct iio_dev *indio_dev)
+{
+ struct ad4030_state *st = iio_priv(indio_dev);
+ u8 offload_bpw;
+
+ if (st->mode == AD4030_OUT_DATA_MD_30_AVERAGED_DIFF)
+ offload_bpw = 32;
+ else
+ offload_bpw = st->chip->precision_bits;
+
+ st->offload_xfer.bits_per_word = offload_bpw;
+ st->offload_xfer.len = spi_bpw_to_bytes(offload_bpw);
+ st->offload_xfer.offload_flags = SPI_OFFLOAD_XFER_RX_STREAM;
+ spi_message_init_with_transfers(&st->offload_msg, &st->offload_xfer, 1);
+}
+
+static int ad4030_offload_buffer_postenable(struct iio_dev *indio_dev)
+{
+ struct ad4030_state *st = iio_priv(indio_dev);
+ unsigned int reg_modes;
+ int ret;
+
+ /*
+ * When data from 2 analog input channels is output through a single
+ * bus line (interleaved mode (LANE_MD == 0b11)) and gets pushed through
+ * DMA, extra hardware is required to do the de-interleaving. While we
+ * don't support such hardware configurations, disallow interleaved mode
+ * when using SPI offload.
+ */
+ ret = regmap_read(st->regmap, AD4030_REG_MODES, ®_modes);
+ if (ret)
+ return ret;
+
+ if (st->chip->num_voltage_inputs > 1 &&
+ FIELD_GET(AD4030_REG_MODES_MASK_LANE_MODE, reg_modes) == AD4030_LANE_MD_INTERLEAVED)
+ return -EINVAL;
+
+ ad4030_prepare_offload_msg(indio_dev);
+ st->offload_msg.offload = st->offload;
+ ret = spi_optimize_message(st->spi, &st->offload_msg);
+ if (ret)
+ return ret;
+
+ ret = pwm_set_waveform_might_sleep(st->cnv_trigger, &st->cnv_wf, false);
+ if (ret)
+ goto out_unoptimize;
+
+ ret = spi_offload_trigger_enable(st->offload, st->offload_trigger,
+ &st->offload_trigger_config);
+ if (ret)
+ goto out_pwm_disable;
+
+ return 0;
+
+out_pwm_disable:
+ pwm_disable(st->cnv_trigger);
+out_unoptimize:
+ spi_unoptimize_message(&st->offload_msg);
+
+ return ret;
+}
+
+static int ad4030_offload_buffer_predisable(struct iio_dev *indio_dev)
+{
+ struct ad4030_state *st = iio_priv(indio_dev);
+
+ spi_offload_trigger_disable(st->offload, st->offload_trigger);
+
+ pwm_disable(st->cnv_trigger);
+
+ spi_unoptimize_message(&st->offload_msg);
+
+ return 0;
+}
+
+static const struct iio_buffer_setup_ops ad4030_offload_buffer_setup_ops = {
+ .postenable = &ad4030_offload_buffer_postenable,
+ .predisable = &ad4030_offload_buffer_predisable,
+};
+
static int ad4030_regulators_get(struct ad4030_state *st)
{
struct device *dev = &st->spi->dev;
@@ -971,6 +1208,24 @@ static int ad4030_detect_chip_info(const struct ad4030_state *st)
return 0;
}
+static int ad4030_pwm_get(struct ad4030_state *st)
+{
+ struct device *dev = &st->spi->dev;
+
+ st->cnv_trigger = devm_pwm_get(dev, NULL);
+ if (IS_ERR(st->cnv_trigger))
+ return dev_err_probe(dev, PTR_ERR(st->cnv_trigger),
+ "Failed to get CNV PWM\n");
+
+ /*
+ * Preemptively disable the PWM, since we only want to enable it with
+ * the buffer.
+ */
+ pwm_disable(st->cnv_trigger);
+
+ return 0;
+}
+
static int ad4030_config(struct ad4030_state *st)
{
int ret;
@@ -998,6 +1253,31 @@ static int ad4030_config(struct ad4030_state *st)
return 0;
}
+static int ad4030_spi_offload_setup(struct iio_dev *indio_dev,
+ struct ad4030_state *st)
+{
+ struct device *dev = &st->spi->dev;
+ struct dma_chan *rx_dma;
+
+ indio_dev->setup_ops = &ad4030_offload_buffer_setup_ops;
+
+ st->offload_trigger = devm_spi_offload_trigger_get(dev, st->offload,
+ SPI_OFFLOAD_TRIGGER_PERIODIC);
+ if (IS_ERR(st->offload_trigger))
+ return dev_err_probe(dev, PTR_ERR(st->offload_trigger),
+ "failed to get offload trigger\n");
+
+ st->offload_trigger_config.type = SPI_OFFLOAD_TRIGGER_PERIODIC;
+
+ rx_dma = devm_spi_offload_rx_stream_request_dma_chan(dev, st->offload);
+ if (IS_ERR(rx_dma))
+ return dev_err_probe(dev, PTR_ERR(rx_dma),
+ "failed to get offload RX DMA\n");
+
+ return devm_iio_dmaengine_buffer_setup_with_handle(dev, indio_dev, rx_dma,
+ IIO_BUFFER_DIRECTION_IN);
+}
+
static int ad4030_probe(struct spi_device *spi)
{
struct device *dev = &spi->dev;
@@ -1049,24 +1329,58 @@ static int ad4030_probe(struct spi_device *spi)
return dev_err_probe(dev, PTR_ERR(st->cnv_gpio),
"Failed to get cnv gpio\n");
- /*
- * One hardware channel is split in two software channels when using
- * common byte mode. Add one more channel for the timestamp.
- */
- indio_dev->num_channels = 2 * st->chip->num_voltage_inputs + 1;
indio_dev->name = st->chip->name;
indio_dev->modes = INDIO_DIRECT_MODE;
indio_dev->info = &ad4030_iio_info;
- indio_dev->channels = st->chip->channels;
indio_dev->available_scan_masks = st->chip->available_masks;
- ret = devm_iio_triggered_buffer_setup(dev, indio_dev,
- iio_pollfunc_store_time,
- ad4030_trigger_handler,
- &ad4030_buffer_setup_ops);
- if (ret)
- return dev_err_probe(dev, ret,
- "Failed to setup triggered buffer\n");
+ st->offload = devm_spi_offload_get(dev, spi, &ad4030_offload_config);
+ ret = PTR_ERR_OR_ZERO(st->offload);
+ /* Fall back to low speed usage when no SPI offload is available. */
+ if (ret == -ENODEV) {
+ /*
+ * One hardware channel is split in two software channels when
+ * using common byte mode. Add one more channel for the timestamp.
+ */
+ indio_dev->num_channels = 2 * st->chip->num_voltage_inputs + 1;
+ indio_dev->channels = st->chip->channels;
+
+ ret = devm_iio_triggered_buffer_setup(dev, indio_dev,
+ iio_pollfunc_store_time,
+ ad4030_trigger_handler,
+ &ad4030_buffer_setup_ops);
+ if (ret)
+ return dev_err_probe(dev, ret,
+ "Failed to setup triggered buffer\n");
+ } else if (ret) {
+ return dev_err_probe(dev, ret, "failed to get offload\n");
+ } else {
+ /*
+ * Offloaded SPI transfers can't support software timestamp so
+ * no additional timestamp channel is added.
+ */
+ indio_dev->num_channels = st->chip->num_voltage_inputs;
+ indio_dev->channels = st->chip->offload_channels;
+ ret = ad4030_spi_offload_setup(indio_dev, st);
+ if (ret)
+ return dev_err_probe(dev, ret,
+ "Failed to setup SPI offload\n");
+
+ ret = ad4030_pwm_get(st);
+ if (ret)
+ return dev_err_probe(dev, ret, "Failed to get PWM\n");
+
+ /*
+ * Start with a slower sampling rate so there is some room for
+ * adjusting the sample averaging and the sampling frequency
+ * without hitting the maximum conversion rate.
+ */
+ ret = ad4030_update_conversion_rate(st, st->chip->max_sample_rate_hz >> 4,
+ st->avg_log2);
+ if (ret)
+ return dev_err_probe(dev, ret,
+ "Failed to set offload samp freq\n");
+ }
return devm_iio_device_register(dev, indio_dev);
}
@@ -1104,11 +1418,28 @@ static const struct iio_scan_type ad4030_24_scan_types[] = {
},
};
+static const struct iio_scan_type ad4030_24_offload_scan_types[] = {
+ [AD4030_SCAN_TYPE_NORMAL] = {
+ .sign = 's',
+ .realbits = 24,
+ .storagebits = 32,
+ .shift = 0,
+ .endianness = IIO_CPU,
+ },
+ [AD4030_SCAN_TYPE_AVG] = {
+ .sign = 's',
+ .realbits = 30,
+ .storagebits = 32,
+ .shift = 2,
+ .endianness = IIO_CPU,
+ },
+};
+
static const struct iio_scan_type ad4030_16_scan_types[] = {
[AD4030_SCAN_TYPE_NORMAL] = {
.sign = 's',
- .storagebits = 32,
.realbits = 16,
+ .storagebits = 32,
.shift = 16,
.endianness = IIO_BE,
},
@@ -1121,6 +1452,23 @@ static const struct iio_scan_type ad4030_16_scan_types[] = {
}
};
+static const struct iio_scan_type ad4030_16_offload_scan_types[] = {
+ [AD4030_SCAN_TYPE_NORMAL] = {
+ .sign = 's',
+ .realbits = 16,
+ .storagebits = 32,
+ .shift = 0,
+ .endianness = IIO_CPU,
+ },
+ [AD4030_SCAN_TYPE_AVG] = {
+ .sign = 's',
+ .realbits = 30,
+ .storagebits = 32,
+ .shift = 2,
+ .endianness = IIO_CPU,
+ },
+};
+
static const struct ad4030_chip_info ad4030_24_chip_info = {
.name = "ad4030-24",
.available_masks = ad4030_channel_masks,
@@ -1129,10 +1477,14 @@ static const struct ad4030_chip_info ad4030_24_chip_info = {
AD4030_CHAN_CMO(1, 0),
IIO_CHAN_SOFT_TIMESTAMP(2),
},
+ .offload_channels = {
+ AD4030_OFFLOAD_CHAN_DIFF(0, ad4030_24_offload_scan_types),
+ },
.grade = AD4030_REG_CHIP_GRADE_AD4030_24_GRADE,
.precision_bits = 24,
.num_voltage_inputs = 1,
.tcyc_ns = AD4030_TCYC_ADJUSTED_NS,
+ .max_sample_rate_hz = 2 * HZ_PER_MHZ,
};
static const struct ad4030_chip_info ad4630_16_chip_info = {
@@ -1145,10 +1497,15 @@ static const struct ad4030_chip_info ad4630_16_chip_info = {
AD4030_CHAN_CMO(3, 1),
IIO_CHAN_SOFT_TIMESTAMP(4),
},
+ .offload_channels = {
+ AD4030_OFFLOAD_CHAN_DIFF(0, ad4030_16_offload_scan_types),
+ AD4030_OFFLOAD_CHAN_DIFF(1, ad4030_16_offload_scan_types),
+ },
.grade = AD4030_REG_CHIP_GRADE_AD4630_16_GRADE,
.precision_bits = 16,
.num_voltage_inputs = 2,
.tcyc_ns = AD4030_TCYC_ADJUSTED_NS,
+ .max_sample_rate_hz = 2 * HZ_PER_MHZ,
};
static const struct ad4030_chip_info ad4630_24_chip_info = {
@@ -1161,10 +1518,15 @@ static const struct ad4030_chip_info ad4630_24_chip_info = {
AD4030_CHAN_CMO(3, 1),
IIO_CHAN_SOFT_TIMESTAMP(4),
},
+ .offload_channels = {
+ AD4030_OFFLOAD_CHAN_DIFF(0, ad4030_24_offload_scan_types),
+ AD4030_OFFLOAD_CHAN_DIFF(1, ad4030_24_offload_scan_types),
+ },
.grade = AD4030_REG_CHIP_GRADE_AD4630_24_GRADE,
.precision_bits = 24,
.num_voltage_inputs = 2,
.tcyc_ns = AD4030_TCYC_ADJUSTED_NS,
+ .max_sample_rate_hz = 2 * HZ_PER_MHZ,
};
static const struct ad4030_chip_info ad4632_16_chip_info = {
@@ -1177,10 +1539,15 @@ static const struct ad4030_chip_info ad4632_16_chip_info = {
AD4030_CHAN_CMO(3, 1),
IIO_CHAN_SOFT_TIMESTAMP(4),
},
+ .offload_channels = {
+ AD4030_OFFLOAD_CHAN_DIFF(0, ad4030_16_offload_scan_types),
+ AD4030_OFFLOAD_CHAN_DIFF(1, ad4030_16_offload_scan_types),
+ },
.grade = AD4030_REG_CHIP_GRADE_AD4632_16_GRADE,
.precision_bits = 16,
.num_voltage_inputs = 2,
.tcyc_ns = AD4632_TCYC_ADJUSTED_NS,
+ .max_sample_rate_hz = 500 * HZ_PER_KHZ,
};
static const struct ad4030_chip_info ad4632_24_chip_info = {
@@ -1193,10 +1560,15 @@ static const struct ad4030_chip_info ad4632_24_chip_info = {
AD4030_CHAN_CMO(3, 1),
IIO_CHAN_SOFT_TIMESTAMP(4),
},
+ .offload_channels = {
+ AD4030_OFFLOAD_CHAN_DIFF(0, ad4030_24_offload_scan_types),
+ AD4030_OFFLOAD_CHAN_DIFF(1, ad4030_24_offload_scan_types),
+ },
.grade = AD4030_REG_CHIP_GRADE_AD4632_24_GRADE,
.precision_bits = 24,
.num_voltage_inputs = 2,
.tcyc_ns = AD4632_TCYC_ADJUSTED_NS,
+ .max_sample_rate_hz = 500 * HZ_PER_KHZ,
};
static const struct spi_device_id ad4030_id_table[] = {
@@ -1232,3 +1604,4 @@ module_spi_driver(ad4030_driver);
MODULE_AUTHOR("Esteban Blanc <eblanc@baylibre.com>");
MODULE_DESCRIPTION("Analog Devices AD4630 ADC family driver");
MODULE_LICENSE("GPL");
+MODULE_IMPORT_NS("IIO_DMAENGINE_BUFFER");
--
2.39.2
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH v10 4/6] dt-bindings: iio: adc: adi,ad4030: Add ADAQ4216 and ADAQ4224
2026-02-23 17:08 [PATCH v10 0/6] Add SPI offload support to AD4030 Marcelo Schmitt
` (2 preceding siblings ...)
2026-02-23 17:09 ` [PATCH v10 3/6] iio: adc: ad4030: Add SPI offload support Marcelo Schmitt
@ 2026-02-23 17:10 ` Marcelo Schmitt
2026-02-23 17:10 ` [PATCH v10 5/6] iio: adc: ad4030: Add support for " Marcelo Schmitt
` (2 subsequent siblings)
6 siblings, 0 replies; 8+ messages in thread
From: Marcelo Schmitt @ 2026-02-23 17:10 UTC (permalink / raw)
To: linux-iio, devicetree, linux-doc, linux-kernel
Cc: jic23, michael.hennerich, nuno.sa, eblanc, dlechner, andy, robh,
krzk+dt, conor+dt, corbet, marcelo.schmitt1, Conor Dooley
ADAQ4216 and ADAQ4224 are similar to AD4030 except that ADAQ devices have a
PGA (programmable gain amplifier) that scales the input signal prior to it
reaching the ADC inputs. The PGA is controlled through a couple of pins (A0
and A1) that set one of four possible signal gain configurations.
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
---
Change log v9 -> v10
- No changes.
.../bindings/iio/adc/adi,ad4030.yaml | 58 +++++++++++++++++++
1 file changed, 58 insertions(+)
diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad4030.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad4030.yaml
index a135c66142df..08b1f9d75f89 100644
--- a/Documentation/devicetree/bindings/iio/adc/adi,ad4030.yaml
+++ b/Documentation/devicetree/bindings/iio/adc/adi,ad4030.yaml
@@ -19,6 +19,8 @@ description: |
* https://www.analog.com/media/en/technical-documentation/data-sheets/ad4030-24-4032-24.pdf
* https://www.analog.com/media/en/technical-documentation/data-sheets/ad4630-24_ad4632-24.pdf
* https://www.analog.com/media/en/technical-documentation/data-sheets/ad4630-16-4632-16.pdf
+ * https://www.analog.com/media/en/technical-documentation/data-sheets/adaq4216.pdf
+ * https://www.analog.com/media/en/technical-documentation/data-sheets/adaq4224.pdf
$ref: /schemas/spi/spi-peripheral-props.yaml#
@@ -31,6 +33,8 @@ properties:
- adi,ad4630-24
- adi,ad4632-16
- adi,ad4632-24
+ - adi,adaq4216
+ - adi,adaq4224
reg:
maxItems: 1
@@ -62,6 +66,14 @@ properties:
description:
Internal buffered Reference. Used when ref-supply is not connected.
+ vddh-supply:
+ description:
+ PGIA Positive Power Supply.
+
+ vdd-fda-supply:
+ description:
+ FDA Positive Power Supply.
+
cnv-gpios:
description:
The Convert Input (CNV). It initiates the sampling conversions.
@@ -72,6 +84,13 @@ properties:
The Reset Input (/RST). Used for asynchronous device reset.
maxItems: 1
+ pga-gpios:
+ description:
+ A0 and A1 pins for gain selection. For devices that have PGA configuration
+ input pins, pga-gpios should be defined.
+ minItems: 2
+ maxItems: 2
+
pwms:
description: PWM signal connected to the CNV pin.
maxItems: 1
@@ -113,6 +132,22 @@ allOf:
properties:
spi-rx-bus-width:
maxItems: 1
+ # ADAQ devices require a gain property to indicate how hardware PGA is set
+ - if:
+ properties:
+ compatible:
+ contains:
+ pattern: ^adi,adaq
+ then:
+ required:
+ - vddh-supply
+ - vdd-fda-supply
+ - pga-gpios
+ properties:
+ ref-supply: false
+ else:
+ properties:
+ pga-gpios: false
examples:
- |
@@ -154,3 +189,26 @@ examples:
reset-gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
};
};
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+
+ spi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ adc@0 {
+ compatible = "adi,adaq4216";
+ reg = <0>;
+ spi-max-frequency = <80000000>;
+ vdd-5v-supply = <&supply_5V>;
+ vdd-1v8-supply = <&supply_1_8V>;
+ vio-supply = <&supply_1_8V>;
+ refin-supply = <&refin_sup>;
+ vddh-supply = <&vddh>;
+ vdd-fda-supply = <&vdd_fda>;
+ cnv-gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
+ pga-gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>,
+ <&gpio0 3 GPIO_ACTIVE_HIGH>;
+ };
+ };
--
2.39.2
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH v10 5/6] iio: adc: ad4030: Add support for ADAQ4216 and ADAQ4224
2026-02-23 17:08 [PATCH v10 0/6] Add SPI offload support to AD4030 Marcelo Schmitt
` (3 preceding siblings ...)
2026-02-23 17:10 ` [PATCH v10 4/6] dt-bindings: iio: adc: adi,ad4030: Add ADAQ4216 and ADAQ4224 Marcelo Schmitt
@ 2026-02-23 17:10 ` Marcelo Schmitt
2026-02-23 17:10 ` [PATCH v10 6/6] iio: adc: ad4030: Support common-mode channels with SPI offloading Marcelo Schmitt
2026-02-28 19:15 ` [PATCH v10 0/6] Add SPI offload support to AD4030 Jonathan Cameron
6 siblings, 0 replies; 8+ messages in thread
From: Marcelo Schmitt @ 2026-02-23 17:10 UTC (permalink / raw)
To: linux-iio, devicetree, linux-doc, linux-kernel
Cc: jic23, michael.hennerich, nuno.sa, eblanc, dlechner, andy, robh,
krzk+dt, conor+dt, corbet, marcelo.schmitt1
ADAQ4216 and ADAQ4224 are similar to AD4030, but feature a PGA circuitry
that scales the analog input signal prior to it reaching the ADC. The PGA
is controlled through a pair of pins (A0 and A1) whose state define the
gain that is applied to the input signal.
Add support for ADAQ4216 and ADAQ4224. Provide a list of PGA options
through the IIO device channel scale available interface and enable control
of the PGA through the channel scale interface.
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
---
Change log v9 -> v10
- Use in-loop counter declaration.
- Correctly prepared patches, dropping unsupported bindings for input gain
control that slipped through in v9.
drivers/iio/adc/ad4030.c | 201 ++++++++++++++++++++++++++++++++++++++-
1 file changed, 198 insertions(+), 3 deletions(-)
diff --git a/drivers/iio/adc/ad4030.c b/drivers/iio/adc/ad4030.c
index 9540ff8c49df..47f733aceb03 100644
--- a/drivers/iio/adc/ad4030.c
+++ b/drivers/iio/adc/ad4030.c
@@ -48,6 +48,8 @@
#define AD4030_REG_CHIP_GRADE_AD4630_24_GRADE 0x00
#define AD4030_REG_CHIP_GRADE_AD4632_16_GRADE 0x05
#define AD4030_REG_CHIP_GRADE_AD4632_24_GRADE 0x02
+#define AD4030_REG_CHIP_GRADE_ADAQ4216_GRADE 0x1E
+#define AD4030_REG_CHIP_GRADE_ADAQ4224_GRADE 0x1C
#define AD4030_REG_CHIP_GRADE_MASK_CHIP_GRADE GENMASK(7, 3)
#define AD4030_REG_SCRATCH_PAD 0x0A
#define AD4030_REG_SPI_REVISION 0x0B
@@ -125,6 +127,10 @@
/* Datasheet says 9.8ns, so use the closest integer value */
#define AD4030_TQUIET_CNV_DELAY_NS 10
+/* HARDWARE_GAIN */
+#define ADAQ4616_PGA_PINS 2
+#define ADAQ4616_PGA_GAIN_MAX_NANO (NANO * 2 / 3)
+
enum ad4030_out_mode {
AD4030_OUT_DATA_MD_DIFF,
AD4030_OUT_DATA_MD_16_DIFF_8_COM,
@@ -145,6 +151,23 @@ enum {
AD4030_SCAN_TYPE_AVG,
};
+/*
+ * Gains computed as fractions of 1000 so they can be expressed by integers.
+ */
+static const int adaq4216_hw_gains_vpv[] = {
+ 1 * MILLI / 3, /* 0.333 */
+ 5 * MILLI / 9, /* 0.555 */
+ 20 * MILLI / 9, /* 0.2222 */
+ 20 * MILLI / 3, /* 0.6666 */
+};
+
+static const int adaq4216_hw_gains_frac[][2] = {
+ { 1, 3 }, /* 1/3 V/V gain */
+ { 5, 9 }, /* 5/9 V/V gain */
+ { 20, 9 }, /* 20/9 V/V gain */
+ { 20, 3 }, /* 20/3 V/V gain */
+};
+
struct ad4030_chip_info {
const char *name;
const unsigned long *available_masks;
@@ -152,6 +175,7 @@ struct ad4030_chip_info {
const struct iio_chan_spec offload_channels[AD4030_MAX_IIO_CHANNEL_NB];
u8 grade;
u8 precision_bits;
+ bool has_pga;
/* Number of hardware channels */
int num_voltage_inputs;
unsigned int tcyc_ns;
@@ -175,7 +199,11 @@ struct ad4030_state {
struct spi_offload_trigger *offload_trigger;
struct spi_offload_trigger_config offload_trigger_config;
struct pwm_device *cnv_trigger;
+ size_t scale_avail_size;
struct pwm_waveform cnv_wf;
+ unsigned int scale_avail[ARRAY_SIZE(adaq4216_hw_gains_vpv)][2];
+ struct gpio_descs *pga_gpios;
+ unsigned int pga_index;
/*
* DMA (thus cache coherency maintenance) requires the transfer buffers
@@ -232,7 +260,7 @@ struct ad4030_state {
* - voltage0-voltage1
* - voltage2-voltage3
*/
-#define __AD4030_CHAN_DIFF(_idx, _scan_type, _offload) { \
+#define __AD4030_CHAN_DIFF(_idx, _scan_type, _offload, _pga) { \
.info_mask_shared_by_all = \
(_offload ? BIT(IIO_CHAN_INFO_SAMP_FREQ) : 0) | \
BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO), \
@@ -243,6 +271,7 @@ struct ad4030_state {
BIT(IIO_CHAN_INFO_CALIBBIAS) | \
BIT(IIO_CHAN_INFO_RAW), \
.info_mask_separate_available = BIT(IIO_CHAN_INFO_CALIBBIAS) | \
+ (_pga ? BIT(IIO_CHAN_INFO_SCALE) : 0) | \
BIT(IIO_CHAN_INFO_CALIBSCALE), \
.type = IIO_VOLTAGE, \
.indexed = 1, \
@@ -257,10 +286,16 @@ struct ad4030_state {
}
#define AD4030_CHAN_DIFF(_idx, _scan_type) \
- __AD4030_CHAN_DIFF(_idx, _scan_type, 0)
+ __AD4030_CHAN_DIFF(_idx, _scan_type, 0, 0)
#define AD4030_OFFLOAD_CHAN_DIFF(_idx, _scan_type) \
- __AD4030_CHAN_DIFF(_idx, _scan_type, 1)
+ __AD4030_CHAN_DIFF(_idx, _scan_type, 1, 0)
+
+#define ADAQ4216_CHAN_DIFF(_idx, _scan_type) \
+ __AD4030_CHAN_DIFF(_idx, _scan_type, 0, 1)
+
+#define ADAQ4216_OFFLOAD_CHAN_DIFF(_idx, _scan_type) \
+ __AD4030_CHAN_DIFF(_idx, _scan_type, 1, 1)
/*
* AD4030 can average over 2^N samples, where N = 1, 2, 3, ..., 16.
@@ -418,6 +453,65 @@ static const struct regmap_config ad4030_regmap_config = {
.max_register = AD4030_REG_DIG_ERR,
};
+static void ad4030_fill_scale_avail(struct ad4030_state *st)
+{
+ unsigned int mag_bits, int_part, fract_part;
+ u64 range;
+
+ /*
+ * The maximum precision of differential channels is retrieved from the
+ * chip properties. The output code of differential channels is in two's
+ * complement format (i.e. signed), so the MSB is the sign bit and only
+ * (precision_bits - 1) bits express voltage magnitude.
+ */
+ mag_bits = st->chip->precision_bits - 1;
+
+ for (unsigned int i = 0; i < ARRAY_SIZE(adaq4216_hw_gains_frac); i++) {
+ range = mult_frac(st->vref_uv, adaq4216_hw_gains_frac[i][1],
+ adaq4216_hw_gains_frac[i][0]);
+ /*
+ * If range were in mV, we would multiply it by NANO below.
+ * Though, range is in µV so multiply it by MICRO only so the
+ * result after right shift and division scales output codes to
+ * millivolts.
+ */
+ int_part = div_u64_rem((range * MICRO) >> mag_bits, NANO, &fract_part);
+ st->scale_avail[i][0] = int_part;
+ st->scale_avail[i][1] = fract_part;
+ }
+}
+
+static int ad4030_set_pga_gain(struct ad4030_state *st)
+{
+ DECLARE_BITMAP(bitmap, ADAQ4616_PGA_PINS) = { };
+
+ bitmap_write(bitmap, st->pga_index, 0, ADAQ4616_PGA_PINS);
+
+ return gpiod_multi_set_value_cansleep(st->pga_gpios, bitmap);
+}
+
+static int ad4030_set_pga(struct iio_dev *indio_dev, int gain_int, int gain_fract)
+{
+ struct ad4030_state *st = iio_priv(indio_dev);
+ unsigned int mag_bits = st->chip->precision_bits - 1;
+ unsigned int tmp;
+ u64 gain_nano;
+
+ if (!st->pga_gpios)
+ return -EINVAL;
+
+ gain_nano = gain_int * NANO + gain_fract;
+ if (!in_range(gain_nano, 1, ADAQ4616_PGA_GAIN_MAX_NANO))
+ return -EINVAL;
+
+ tmp = DIV_ROUND_CLOSEST_ULL(gain_nano << mag_bits, NANO);
+ gain_nano = DIV_ROUND_CLOSEST(st->vref_uv, tmp);
+ st->pga_index = find_closest(gain_nano, adaq4216_hw_gains_vpv,
+ ARRAY_SIZE(adaq4216_hw_gains_vpv));
+
+ return ad4030_set_pga_gain(st);
+}
+
static int ad4030_get_chan_scale(struct iio_dev *indio_dev,
struct iio_chan_spec const *chan,
int *val,
@@ -430,6 +524,13 @@ static int ad4030_get_chan_scale(struct iio_dev *indio_dev,
if (IS_ERR(scan_type))
return PTR_ERR(scan_type);
+ /* The LSB of the 8-bit common-mode data is always vref/256. */
+ if (st->chip->has_pga && scan_type->realbits != 8) {
+ *val = st->scale_avail[st->pga_index][0];
+ *val2 = st->scale_avail[st->pga_index][1];
+ return IIO_VAL_INT_PLUS_NANO;
+ }
+
if (chan->differential)
*val = (st->vref_uv * 2) / MILLI;
else
@@ -898,6 +999,15 @@ static int ad4030_read_avail(struct iio_dev *indio_dev,
*length = ARRAY_SIZE(ad4030_average_modes);
return IIO_AVAIL_LIST;
+ case IIO_CHAN_INFO_SCALE:
+ if (st->scale_avail_size == 1)
+ *vals = (int *)st->scale_avail[st->pga_index];
+ else
+ *vals = (int *)st->scale_avail;
+ *length = st->scale_avail_size * 2; /* print int and nano part */
+ *type = IIO_VAL_INT_PLUS_NANO;
+ return IIO_AVAIL_LIST;
+
default:
return -EINVAL;
}
@@ -970,6 +1080,9 @@ static int ad4030_write_raw_dispatch(struct iio_dev *indio_dev,
case IIO_CHAN_INFO_SAMP_FREQ:
return ad4030_set_sampling_freq(indio_dev, val);
+ case IIO_CHAN_INFO_SCALE:
+ return ad4030_set_pga(indio_dev, val, val2);
+
default:
return -EINVAL;
}
@@ -991,6 +1104,17 @@ static int ad4030_write_raw(struct iio_dev *indio_dev,
return ret;
}
+static int ad4030_write_raw_get_fmt(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan, long mask)
+{
+ switch (mask) {
+ case IIO_CHAN_INFO_SCALE:
+ return IIO_VAL_INT_PLUS_NANO;
+ default:
+ return IIO_VAL_INT_PLUS_MICRO;
+ }
+}
+
static int ad4030_reg_access(struct iio_dev *indio_dev, unsigned int reg,
unsigned int writeval, unsigned int *readval)
{
@@ -1037,6 +1161,7 @@ static const struct iio_info ad4030_iio_info = {
.read_avail = ad4030_read_avail,
.read_raw = ad4030_read_raw,
.write_raw = ad4030_write_raw,
+ .write_raw_get_fmt = &ad4030_write_raw_get_fmt,
.debugfs_reg_access = ad4030_reg_access,
.read_label = ad4030_read_label,
.get_current_scan_type = ad4030_get_current_scan_type,
@@ -1278,6 +1403,26 @@ static int ad4030_spi_offload_setup(struct iio_dev *indio_dev,
IIO_BUFFER_DIRECTION_IN);
}
+static int ad4030_setup_pga(struct device *dev, struct iio_dev *indio_dev,
+ struct ad4030_state *st)
+{
+ /* Setup GPIOs for PGA control */
+ st->pga_gpios = devm_gpiod_get_array(dev, "pga", GPIOD_OUT_LOW);
+ if (IS_ERR(st->pga_gpios))
+ return dev_err_probe(dev, PTR_ERR(st->pga_gpios),
+ "Failed to get PGA gpios.\n");
+
+ if (st->pga_gpios->ndescs != ADAQ4616_PGA_PINS)
+ return dev_err_probe(dev, -EINVAL,
+ "Expected %d GPIOs for PGA control.\n",
+ ADAQ4616_PGA_PINS);
+
+ st->scale_avail_size = ARRAY_SIZE(adaq4216_hw_gains_vpv);
+ st->pga_index = 0;
+
+ return 0;
+}
+
static int ad4030_probe(struct spi_device *spi)
{
struct device *dev = &spi->dev;
@@ -1320,6 +1465,14 @@ static int ad4030_probe(struct spi_device *spi)
if (ret)
return ret;
+ if (st->chip->has_pga) {
+ ret = ad4030_setup_pga(dev, indio_dev, st);
+ if (ret)
+ return ret;
+
+ ad4030_fill_scale_avail(st);
+ }
+
ret = ad4030_config(st);
if (ret)
return ret;
@@ -1571,12 +1724,52 @@ static const struct ad4030_chip_info ad4632_24_chip_info = {
.max_sample_rate_hz = 500 * HZ_PER_KHZ,
};
+static const struct ad4030_chip_info adaq4216_chip_info = {
+ .name = "adaq4216",
+ .available_masks = ad4030_channel_masks,
+ .channels = {
+ ADAQ4216_CHAN_DIFF(0, ad4030_16_scan_types),
+ AD4030_CHAN_CMO(1, 0),
+ IIO_CHAN_SOFT_TIMESTAMP(2),
+ },
+ .offload_channels = {
+ ADAQ4216_OFFLOAD_CHAN_DIFF(0, ad4030_16_offload_scan_types),
+ },
+ .grade = AD4030_REG_CHIP_GRADE_ADAQ4216_GRADE,
+ .precision_bits = 16,
+ .has_pga = true,
+ .num_voltage_inputs = 1,
+ .tcyc_ns = AD4030_TCYC_ADJUSTED_NS,
+ .max_sample_rate_hz = 2 * HZ_PER_MHZ,
+};
+
+static const struct ad4030_chip_info adaq4224_chip_info = {
+ .name = "adaq4224",
+ .available_masks = ad4030_channel_masks,
+ .channels = {
+ ADAQ4216_CHAN_DIFF(0, ad4030_24_scan_types),
+ AD4030_CHAN_CMO(1, 0),
+ IIO_CHAN_SOFT_TIMESTAMP(2),
+ },
+ .offload_channels = {
+ ADAQ4216_OFFLOAD_CHAN_DIFF(0, ad4030_24_offload_scan_types),
+ },
+ .grade = AD4030_REG_CHIP_GRADE_ADAQ4224_GRADE,
+ .precision_bits = 24,
+ .has_pga = true,
+ .num_voltage_inputs = 1,
+ .tcyc_ns = AD4030_TCYC_ADJUSTED_NS,
+ .max_sample_rate_hz = 2 * HZ_PER_MHZ,
+};
+
static const struct spi_device_id ad4030_id_table[] = {
{ "ad4030-24", (kernel_ulong_t)&ad4030_24_chip_info },
{ "ad4630-16", (kernel_ulong_t)&ad4630_16_chip_info },
{ "ad4630-24", (kernel_ulong_t)&ad4630_24_chip_info },
{ "ad4632-16", (kernel_ulong_t)&ad4632_16_chip_info },
{ "ad4632-24", (kernel_ulong_t)&ad4632_24_chip_info },
+ { "adaq4216", (kernel_ulong_t)&adaq4216_chip_info },
+ { "adaq4224", (kernel_ulong_t)&adaq4224_chip_info },
{ }
};
MODULE_DEVICE_TABLE(spi, ad4030_id_table);
@@ -1587,6 +1780,8 @@ static const struct of_device_id ad4030_of_match[] = {
{ .compatible = "adi,ad4630-24", .data = &ad4630_24_chip_info },
{ .compatible = "adi,ad4632-16", .data = &ad4632_16_chip_info },
{ .compatible = "adi,ad4632-24", .data = &ad4632_24_chip_info },
+ { .compatible = "adi,adaq4216", .data = &adaq4216_chip_info },
+ { .compatible = "adi,adaq4224", .data = &adaq4224_chip_info },
{ }
};
MODULE_DEVICE_TABLE(of, ad4030_of_match);
--
2.39.2
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH v10 6/6] iio: adc: ad4030: Support common-mode channels with SPI offloading
2026-02-23 17:08 [PATCH v10 0/6] Add SPI offload support to AD4030 Marcelo Schmitt
` (4 preceding siblings ...)
2026-02-23 17:10 ` [PATCH v10 5/6] iio: adc: ad4030: Add support for " Marcelo Schmitt
@ 2026-02-23 17:10 ` Marcelo Schmitt
2026-02-28 19:15 ` [PATCH v10 0/6] Add SPI offload support to AD4030 Jonathan Cameron
6 siblings, 0 replies; 8+ messages in thread
From: Marcelo Schmitt @ 2026-02-23 17:10 UTC (permalink / raw)
To: linux-iio, devicetree, linux-doc, linux-kernel
Cc: jic23, michael.hennerich, nuno.sa, eblanc, dlechner, andy, robh,
krzk+dt, conor+dt, corbet, marcelo.schmitt1, David Lechner
AD4030 and similar devices can read common-mode voltage together with
ADC sample data. When enabled, common-mode voltage data is provided in a
separate IIO channel since it measures something other than the primary
ADC input signal and requires separate scaling to convert to voltage
units. The initial SPI offload support patch for AD4030 only provided
differential channels. Now, extend the AD4030 driver to also provide
common-mode IIO channels when setup with SPI offloading capability.
Reviewed-by: David Lechner <dlechner@baylible.com>
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
---
Change log v9 -> v10
- No changes.
drivers/iio/adc/ad4030.c | 49 ++++++++++++++++++++++++++++++++--------
1 file changed, 40 insertions(+), 9 deletions(-)
diff --git a/drivers/iio/adc/ad4030.c b/drivers/iio/adc/ad4030.c
index 47f733aceb03..8414ab73345e 100644
--- a/drivers/iio/adc/ad4030.c
+++ b/drivers/iio/adc/ad4030.c
@@ -193,7 +193,7 @@ struct ad4030_state {
unsigned int avg_log2;
enum ad4030_out_mode mode;
/* Offload sampling */
- struct spi_transfer offload_xfer;
+ struct spi_transfer offload_xfer[2];
struct spi_message offload_msg;
struct spi_offload *offload;
struct spi_offload_trigger *offload_trigger;
@@ -238,7 +238,7 @@ struct ad4030_state {
* - _idx - _ch * 2 + _ch gives the channel number for this specific common-mode
* channel
*/
-#define AD4030_CHAN_CMO(_idx, _ch) { \
+#define __AD4030_CHAN_CMO(_idx, _ch, _offload) { \
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
BIT(IIO_CHAN_INFO_SCALE), \
.type = IIO_VOLTAGE, \
@@ -248,12 +248,18 @@ struct ad4030_state {
.scan_index = (_idx), \
.scan_type = { \
.sign = 'u', \
- .storagebits = 8, \
+ .storagebits = (_offload ? 32 : 8), \
.realbits = 8, \
- .endianness = IIO_BE, \
+ .endianness = (_offload ? IIO_CPU : IIO_BE), \
}, \
}
+#define AD4030_CHAN_CMO(_idx, _ch) \
+ __AD4030_CHAN_CMO(_idx, _ch, 0)
+
+#define AD4030_OFFLOAD_CHAN_CMO(_idx, _ch) \
+ __AD4030_CHAN_CMO(_idx, _ch, 1)
+
/*
* For a chip with 2 hardware channel this will be used to create 2 differential
* channels:
@@ -1187,6 +1193,7 @@ static const struct iio_buffer_setup_ops ad4030_buffer_setup_ops = {
static void ad4030_prepare_offload_msg(struct iio_dev *indio_dev)
{
struct ad4030_state *st = iio_priv(indio_dev);
+ bool common_mode;
u8 offload_bpw;
if (st->mode == AD4030_OUT_DATA_MD_30_AVERAGED_DIFF)
@@ -1194,10 +1201,22 @@ static void ad4030_prepare_offload_msg(struct iio_dev *indio_dev)
else
offload_bpw = st->chip->precision_bits;
- st->offload_xfer.bits_per_word = offload_bpw;
- st->offload_xfer.len = spi_bpw_to_bytes(offload_bpw);
- st->offload_xfer.offload_flags = SPI_OFFLOAD_XFER_RX_STREAM;
- spi_message_init_with_transfers(&st->offload_msg, &st->offload_xfer, 1);
+ st->offload_xfer[0].bits_per_word = offload_bpw;
+ st->offload_xfer[0].len = spi_bpw_to_bytes(offload_bpw);
+ st->offload_xfer[0].offload_flags = SPI_OFFLOAD_XFER_RX_STREAM;
+
+ common_mode = st->mode == AD4030_OUT_DATA_MD_24_DIFF_8_COM ||
+ st->mode == AD4030_OUT_DATA_MD_16_DIFF_8_COM;
+
+ if (common_mode) {
+ offload_bpw = 8;
+ st->offload_xfer[1].bits_per_word = offload_bpw;
+ st->offload_xfer[1].len = spi_bpw_to_bytes(offload_bpw);
+ st->offload_xfer[1].offload_flags = SPI_OFFLOAD_XFER_RX_STREAM;
+ }
+
+ spi_message_init_with_transfers(&st->offload_msg, st->offload_xfer,
+ common_mode ? 2 : 1);
}
static int ad4030_offload_buffer_postenable(struct iio_dev *indio_dev)
@@ -1262,6 +1281,7 @@ static int ad4030_offload_buffer_predisable(struct iio_dev *indio_dev)
static const struct iio_buffer_setup_ops ad4030_offload_buffer_setup_ops = {
.postenable = &ad4030_offload_buffer_postenable,
.predisable = &ad4030_offload_buffer_predisable,
+ .validate_scan_mask = ad4030_validate_scan_mask,
};
static int ad4030_regulators_get(struct ad4030_state *st)
@@ -1512,7 +1532,7 @@ static int ad4030_probe(struct spi_device *spi)
* Offloaded SPI transfers can't support software timestamp so
* no additional timestamp channel is added.
*/
- indio_dev->num_channels = st->chip->num_voltage_inputs;
+ indio_dev->num_channels = 2 * st->chip->num_voltage_inputs;
indio_dev->channels = st->chip->offload_channels;
ret = ad4030_spi_offload_setup(indio_dev, st);
if (ret)
@@ -1632,6 +1652,7 @@ static const struct ad4030_chip_info ad4030_24_chip_info = {
},
.offload_channels = {
AD4030_OFFLOAD_CHAN_DIFF(0, ad4030_24_offload_scan_types),
+ AD4030_OFFLOAD_CHAN_CMO(1, 0),
},
.grade = AD4030_REG_CHIP_GRADE_AD4030_24_GRADE,
.precision_bits = 24,
@@ -1653,6 +1674,8 @@ static const struct ad4030_chip_info ad4630_16_chip_info = {
.offload_channels = {
AD4030_OFFLOAD_CHAN_DIFF(0, ad4030_16_offload_scan_types),
AD4030_OFFLOAD_CHAN_DIFF(1, ad4030_16_offload_scan_types),
+ AD4030_OFFLOAD_CHAN_CMO(2, 0),
+ AD4030_OFFLOAD_CHAN_CMO(3, 1),
},
.grade = AD4030_REG_CHIP_GRADE_AD4630_16_GRADE,
.precision_bits = 16,
@@ -1674,6 +1697,8 @@ static const struct ad4030_chip_info ad4630_24_chip_info = {
.offload_channels = {
AD4030_OFFLOAD_CHAN_DIFF(0, ad4030_24_offload_scan_types),
AD4030_OFFLOAD_CHAN_DIFF(1, ad4030_24_offload_scan_types),
+ AD4030_OFFLOAD_CHAN_CMO(2, 0),
+ AD4030_OFFLOAD_CHAN_CMO(3, 1),
},
.grade = AD4030_REG_CHIP_GRADE_AD4630_24_GRADE,
.precision_bits = 24,
@@ -1695,6 +1720,8 @@ static const struct ad4030_chip_info ad4632_16_chip_info = {
.offload_channels = {
AD4030_OFFLOAD_CHAN_DIFF(0, ad4030_16_offload_scan_types),
AD4030_OFFLOAD_CHAN_DIFF(1, ad4030_16_offload_scan_types),
+ AD4030_OFFLOAD_CHAN_CMO(2, 0),
+ AD4030_OFFLOAD_CHAN_CMO(3, 1),
},
.grade = AD4030_REG_CHIP_GRADE_AD4632_16_GRADE,
.precision_bits = 16,
@@ -1716,6 +1743,8 @@ static const struct ad4030_chip_info ad4632_24_chip_info = {
.offload_channels = {
AD4030_OFFLOAD_CHAN_DIFF(0, ad4030_24_offload_scan_types),
AD4030_OFFLOAD_CHAN_DIFF(1, ad4030_24_offload_scan_types),
+ AD4030_OFFLOAD_CHAN_CMO(2, 0),
+ AD4030_OFFLOAD_CHAN_CMO(3, 1),
},
.grade = AD4030_REG_CHIP_GRADE_AD4632_24_GRADE,
.precision_bits = 24,
@@ -1734,6 +1763,7 @@ static const struct ad4030_chip_info adaq4216_chip_info = {
},
.offload_channels = {
ADAQ4216_OFFLOAD_CHAN_DIFF(0, ad4030_16_offload_scan_types),
+ AD4030_OFFLOAD_CHAN_CMO(1, 0),
},
.grade = AD4030_REG_CHIP_GRADE_ADAQ4216_GRADE,
.precision_bits = 16,
@@ -1753,6 +1783,7 @@ static const struct ad4030_chip_info adaq4224_chip_info = {
},
.offload_channels = {
ADAQ4216_OFFLOAD_CHAN_DIFF(0, ad4030_24_offload_scan_types),
+ AD4030_OFFLOAD_CHAN_CMO(1, 0),
},
.grade = AD4030_REG_CHIP_GRADE_ADAQ4224_GRADE,
.precision_bits = 24,
--
2.39.2
^ permalink raw reply related [flat|nested] 8+ messages in thread* Re: [PATCH v10 0/6] Add SPI offload support to AD4030
2026-02-23 17:08 [PATCH v10 0/6] Add SPI offload support to AD4030 Marcelo Schmitt
` (5 preceding siblings ...)
2026-02-23 17:10 ` [PATCH v10 6/6] iio: adc: ad4030: Support common-mode channels with SPI offloading Marcelo Schmitt
@ 2026-02-28 19:15 ` Jonathan Cameron
6 siblings, 0 replies; 8+ messages in thread
From: Jonathan Cameron @ 2026-02-28 19:15 UTC (permalink / raw)
To: Marcelo Schmitt
Cc: linux-iio, devicetree, linux-doc, linux-kernel, michael.hennerich,
nuno.sa, eblanc, dlechner, andy, robh, krzk+dt, conor+dt, corbet,
marcelo.schmitt1
On Mon, 23 Feb 2026 14:08:50 -0300
Marcelo Schmitt <marcelo.schmitt@analog.com> wrote:
> Hello,
>
> This is v10 of high speed data capture support for AD4030/AD4630 and similar ADCs.
> It also adds support for ADAQ4216 and ADAQ4224.
>
> Rebased on top of IIO testing.
Series applied to the togreg branch of iio.git and pushed out as testing.
Thanks!
J
>
> Looks like a devm_pwm_get_disabled() interface might not get accepted so I
> didn't change the handling of PWM initialization on v10.
>
> Change log v9 -> v10
> [DT]
> - No changes.
> [IIO]
> - Explained the need of PWM in commint message.
> - Fixed off-by-one bug.
> - Use in-loop counter declaration.
> - Correctly prepared patches, dropping unsupported bindings for input gain control.
> - Skipped the patches applied from previous version.
> - Initialize iio_scan_type struct fields on same order they are on structure definition.
>
> Link to v9: https://lore.kernel.org/linux-iio/cover.1771253601.git.marcelo.schmitt@analog.com/
>
> Thanks,
> Marcelo
>
> Marcelo Schmitt (6):
> Docs: iio: ad4030: Add double PWM SPI offload doc
> dt-bindings: iio: adc: adi,ad4030: Add PWM
> iio: adc: ad4030: Add SPI offload support
> dt-bindings: iio: adc: adi,ad4030: Add ADAQ4216 and ADAQ4224
> iio: adc: ad4030: Add support for ADAQ4216 and ADAQ4224
> iio: adc: ad4030: Support common-mode channels with SPI offloading
>
> .../bindings/iio/adc/adi,ad4030.yaml | 62 ++
> Documentation/iio/ad4030.rst | 39 ++
> drivers/iio/adc/Kconfig | 5 +
> drivers/iio/adc/ad4030.c | 641 +++++++++++++++++-
> 4 files changed, 726 insertions(+), 21 deletions(-)
>
>
> base-commit: 0be8a2716187607daaa8ba80687a926438d88432
^ permalink raw reply [flat|nested] 8+ messages in thread