Re: [PATCH v2 6/8] arm64: dts: qcom: Add PMI632 PMIC

[Konrad Dybcio <konrad.dybcio@linaro.org>]

On 18.04.2023 18:43, Luca Weiss wrote:
> The PMI632, commonly found on SoCs with SDM632 has various standard
> functions like ADC, GPIOs, LPG and more.
> 
> Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
> ---
Looks good!

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad
>  arch/arm64/boot/dts/qcom/pmi632.dtsi | 165 +++++++++++++++++++++++++++++++++++
>  1 file changed, 165 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/pmi632.dtsi b/arch/arm64/boot/dts/qcom/pmi632.dtsi
> new file mode 100644
> index 000000000000..4eb79e0ce40a
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/pmi632.dtsi
> @@ -0,0 +1,165 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (C) 2023 Luca Weiss <luca@z3ntu.xyz>
> + */
> +
> +#include <dt-bindings/iio/qcom,spmi-vadc.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/spmi/spmi.h>
> +
> +/ {
> +	thermal-zones {
> +		pmi632-thermal {
> +			polling-delay-passive = <100>;
> +			polling-delay = <0>;
> +
> +			thermal-sensors = <&pmi632_temp>;
> +
> +			trips {
> +				trip0 {
> +					temperature = <95000>;
> +					hysteresis = <0>;
> +					type = "passive";
> +				};
> +
> +				trip1 {
> +					temperature = <115000>;
> +					hysteresis = <0>;
> +					type = "hot";
> +				};
> +
> +				trip2 {
> +					temperature = <125000>;
> +					hysteresis = <0>;
> +					type = "critical";
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +&spmi_bus {
> +	pmic@2 {
> +		compatible = "qcom,pmi632", "qcom,spmi-pmic";
> +		reg = <0x2 SPMI_USID>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		pmi632_temp: temp-alarm@2400 {
> +			compatible = "qcom,spmi-temp-alarm";
> +			reg = <0x2400>;
> +			interrupts = <0x2 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
> +			#thermal-sensor-cells = <0>;
> +		};
> +
> +		pmi632_adc: adc@3100 {
> +			compatible = "qcom,spmi-adc5";
> +			reg = <0x3100>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			#io-channel-cells = <1>;
> +			interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
> +
> +			channel@0 {
> +				reg = <ADC5_REF_GND>;
> +				qcom,pre-scaling = <1 1>;
> +				label = "ref_gnd";
> +			};
> +
> +			channel@1 {
> +				reg = <ADC5_1P25VREF>;
> +				qcom,pre-scaling = <1 1>;
> +				label = "vref_1p25";
> +			};
> +
> +			channel@6 {
> +				reg = <ADC5_DIE_TEMP>;
> +				qcom,pre-scaling = <1 1>;
> +				label = "die_temp";
> +			};
> +
> +			channel@7 {
> +				reg = <ADC5_USB_IN_I>;
> +				qcom,pre-scaling = <1 1>;
> +				label = "usb_in_i_uv";
> +			};
> +
> +			channel@8 {
> +				reg = <ADC5_USB_IN_V_16>;
> +				qcom,pre-scaling = <1 16>;
> +				label = "usb_in_v_div_16";
> +			};
> +
> +			channel@9 {
> +				reg = <ADC5_CHG_TEMP>;
> +				qcom,pre-scaling = <1 1>;
> +				label = "chg_temp";
> +			};
> +
> +			channel@4b {
> +				reg = <ADC5_BAT_ID_100K_PU>;
> +				qcom,hw-settle-time = <200>;
> +				qcom,pre-scaling = <1 1>;
> +				qcom,ratiometric;
> +				label = "bat_id";
> +			};
> +
> +			channel@83 {
> +				reg = <ADC5_VPH_PWR>;
> +				qcom,pre-scaling = <1 3>;
> +				label = "vph_pwr";
> +			};
> +
> +			channel@84 {
> +				reg = <ADC5_VBAT_SNS>;
> +				qcom,pre-scaling = <1 3>;
> +				label = "vbat_sns";
> +			};
> +		};
> +
> +		pmi632_adc_tm: adc-tm@3500 {
> +			compatible = "qcom,spmi-adc-tm5";
> +			reg = <0x3500>;
> +			interrupts = <0x2 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
> +			#thermal-sensor-cells = <1>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +
> +		pmi632_sdam_7: nvram@b600 {
> +			compatible = "qcom,spmi-sdam";
> +			reg = <0xb600>;
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges = <0 0xb600 0x100>;
> +		};
> +
> +		pmi632_gpios: gpio@c000 {
> +			compatible = "qcom,pmi632-gpio", "qcom,spmi-gpio";
> +			reg = <0xc000>;
> +			gpio-controller;
> +			gpio-ranges = <&pmi632_gpios 0 0 8>;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +	};
> +
> +	pmic@3 {
> +		compatible = "qcom,pmi632", "qcom,spmi-pmic";
> +		reg = <0x3 SPMI_USID>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		pmi632_lpg: pwm {
> +			compatible = "qcom,pmi632-lpg";
> +
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			#pwm-cells = <2>;
> +
> +			status = "disabled";
> +		};
> +	};
> +};
>