linux-ext4.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Zhang Yi <yi.zhang@huawei.com>
To: <linux-ext4@vger.kernel.org>
Cc: <tytso@mit.edu>, <adilger.kernel@dilger.ca>, <jack@suse.cz>,
	<yi.zhang@huawei.com>, <yukuai3@huawei.com>
Subject: [PATCH v2 1/4] ext4: check and update i_disksize properly
Date: Thu, 15 Jul 2021 09:54:49 +0800	[thread overview]
Message-ID: <20210715015452.2542505-2-yi.zhang@huawei.com> (raw)
In-Reply-To: <20210715015452.2542505-1-yi.zhang@huawei.com>

After commit 3da40c7b0898 ("ext4: only call ext4_truncate when size <=
isize"), i_disksize could always be updated to i_size in ext4_setattr(),
and we could sure that i_disksize <= i_size since holding inode lock and
if i_disksize < i_size there are delalloc writes pending in the range
upto i_size. If the end of the current write is <= i_size, there's no
need to touch i_disksize since writeback will push i_disksize upto
i_size eventually. So we can switch to check i_size instead of
i_disksize in ext4_da_write_end() when write to the end of the file.
we also could remove ext4_mark_inode_dirty() together because we defer
inode dirtying to generic_write_end() or ext4_da_write_inline_data_end().

Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
---
 fs/ext4/inode.c | 34 ++++++++++++++++++----------------
 1 file changed, 18 insertions(+), 16 deletions(-)

diff --git a/fs/ext4/inode.c b/fs/ext4/inode.c
index d8de607849df..dca8e3810443 100644
--- a/fs/ext4/inode.c
+++ b/fs/ext4/inode.c
@@ -3084,35 +3084,37 @@ static int ext4_da_write_end(struct file *file,
 	end = start + copied - 1;
 
 	/*
-	 * generic_write_end() will run mark_inode_dirty() if i_size
-	 * changes.  So let's piggyback the i_disksize mark_inode_dirty
-	 * into that.
+	 * Since we are holding inode lock, we are sure i_disksize <=
+	 * i_size. We also know that if i_disksize < i_size, there are
+	 * delalloc writes pending in the range upto i_size. If the end of
+	 * the current write is <= i_size, there's no need to touch
+	 * i_disksize since writeback will push i_disksize upto i_size
+	 * eventually. If the end of the current write is > i_size and
+	 * inside an allocated block (ext4_da_should_update_i_disksize()
+	 * check), we need to update i_disksize here as neither
+	 * ext4_writepage() nor certain ext4_writepages() paths not
+	 * allocating blocks update i_disksize.
+	 *
+	 * Note that we defer inode dirtying to generic_write_end() /
+	 * ext4_da_write_inline_data_end().
 	 */
 	new_i_size = pos + copied;
-	if (copied && new_i_size > EXT4_I(inode)->i_disksize) {
+	if (copied && new_i_size > inode->i_size) {
 		if (ext4_has_inline_data(inode) ||
-		    ext4_da_should_update_i_disksize(page, end)) {
+		    ext4_da_should_update_i_disksize(page, end))
 			ext4_update_i_disksize(inode, new_i_size);
-			/* We need to mark inode dirty even if
-			 * new_i_size is less that inode->i_size
-			 * bu greater than i_disksize.(hint delalloc)
-			 */
-			ret = ext4_mark_inode_dirty(handle, inode);
-		}
 	}
 
 	if (write_mode != CONVERT_INLINE_DATA &&
 	    ext4_test_inode_state(inode, EXT4_STATE_MAY_INLINE_DATA) &&
 	    ext4_has_inline_data(inode))
-		ret2 = ext4_da_write_inline_data_end(inode, pos, len, copied,
+		ret = ext4_da_write_inline_data_end(inode, pos, len, copied,
 						     page);
 	else
-		ret2 = generic_write_end(file, mapping, pos, len, copied,
+		ret = generic_write_end(file, mapping, pos, len, copied,
 							page, fsdata);
 
-	copied = ret2;
-	if (ret2 < 0)
-		ret = ret2;
+	copied = ret;
 	ret2 = ext4_journal_stop(handle);
 	if (unlikely(ret2 && !ret))
 		ret = ret2;
-- 
2.31.1


  reply	other threads:[~2021-07-15  1:46 UTC|newest]

Thread overview: 10+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-07-15  1:54 [PATCH v2 0/4] ext4: improve delalloc buffer write performance Zhang Yi
2021-07-15  1:54 ` Zhang Yi [this message]
2021-07-15 11:52   ` [PATCH v2 1/4] ext4: check and update i_disksize properly Jan Kara
2021-07-15  1:54 ` [PATCH v2 2/4] ext4: correct the error path of ext4_write_inline_data_end() Zhang Yi
2021-07-15  1:54 ` [PATCH v2 3/4] ext4: factor out write end code of inline file Zhang Yi
2021-07-15 12:08   ` Jan Kara
2021-07-16  3:56     ` Zhang Yi
2021-07-16 10:08       ` Jan Kara
2021-07-16 12:04         ` Zhang Yi
2021-07-15  1:54 ` [PATCH v2 4/4] ext4: drop unnecessary journal handle in delalloc write Zhang Yi

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20210715015452.2542505-2-yi.zhang@huawei.com \
    --to=yi.zhang@huawei.com \
    --cc=adilger.kernel@dilger.ca \
    --cc=jack@suse.cz \
    --cc=linux-ext4@vger.kernel.org \
    --cc=tytso@mit.edu \
    --cc=yukuai3@huawei.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).