[RFC 2.6.26-rc3 4/5] am200epd: remove am200epd platform device driver

[Jaya Kumar <jayakumar.lkml@gmail.com>]

The am200epd driver was designed with bad assumptions. It manipulated
GPSR/GPLR registers directly. It relied on direct access to the pxa LCDC
registers which have since conflicted with commit
ce4fb7b892a6d6c6a0f87366b26fd834d2923dd7 . Thus, it is broken and this patch
removes it.

Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
---
 drivers/video/Kconfig    |   13 --
 drivers/video/Makefile   |    1 -
 drivers/video/am200epd.c |  295 ----------------------------------------------
 3 files changed, 0 insertions(+), 309 deletions(-)
 delete mode 100644 drivers/video/am200epd.c

diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index 002b61b..2bbd328 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -1937,19 +1937,6 @@ config FB_XILINX
 	  framebuffer. ML300 carries a 640*480 LCD display on the board,
 	  ML403 uses a standard DB15 VGA connector.
 
-config FB_AM200EPD
-       tristate "AM-200 E-Ink EPD devkit support"
-       depends on FB && ARCH_PXA && MMU
-       select FB_SYS_FILLRECT
-       select FB_SYS_COPYAREA
-       select FB_SYS_IMAGEBLIT
-       select FB_SYS_FOPS
-       select FB_DEFERRED_IO
-       select FB_METRONOME
-       help
-         This enables support for the Metronome display controller used on
-         the E-Ink AM-200 EPD devkit.
-
 config FB_VIRTUAL
 	tristate "Virtual Frame Buffer support (ONLY FOR TESTING!)"
 	depends on FB
diff --git a/drivers/video/Makefile b/drivers/video/Makefile
index 04bca35..80d5842 100644
--- a/drivers/video/Makefile
+++ b/drivers/video/Makefile
@@ -29,7 +29,6 @@ obj-$(CONFIG_FB_DEFERRED_IO)   += fb_defio.o
 
 # Hardware specific drivers go first
 obj-$(CONFIG_FB_AMIGA)            += amifb.o c2p.o
-obj-$(CONFIG_FB_AM200EPD)         += am200epd.o
 obj-$(CONFIG_FB_ARC)              += arcfb.o
 obj-$(CONFIG_FB_CLPS711X)         += clps711xfb.o
 obj-$(CONFIG_FB_CYBER2000)        += cyber2000fb.o
diff --git a/drivers/video/am200epd.c b/drivers/video/am200epd.c
deleted file mode 100644
index 51e26c1..0000000
--- a/drivers/video/am200epd.c
+++ /dev/null
@@ -1,295 +0,0 @@
-/*
- * linux/drivers/video/am200epd.c -- Platform device for AM200 EPD kit
- *
- * Copyright (C) 2008, Jaya Kumar
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file COPYING in the main directory of this archive for
- * more details.
- *
- * Layout is based on skeletonfb.c by James Simmons and Geert Uytterhoeven.
- *
- * This work was made possible by help and equipment support from E-Ink
- * Corporation. http://support.eink.com/community
- *
- * This driver is written to be used with the Metronome display controller.
- * on the AM200 EPD prototype kit/development kit with an E-Ink 800x600
- * Vizplex EPD on a Gumstix board using the Lyre interface board.
- *
- */
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/errno.h>
-#include <linux/string.h>
-#include <linux/delay.h>
-#include <linux/interrupt.h>
-#include <linux/fb.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/list.h>
-#include <linux/uaccess.h>
-#include <linux/irq.h>
-
-#include <video/metronomefb.h>
-
-#include <asm/arch/pxa-regs.h>
-
-/* register offsets for gpio control */
-#define LED_GPIO_PIN 51
-#define STDBY_GPIO_PIN 48
-#define RST_GPIO_PIN 49
-#define RDY_GPIO_PIN 32
-#define ERR_GPIO_PIN 17
-#define PCBPWR_GPIO_PIN 16
-
-#define AF_SEL_GPIO_N 0x3
-#define GAFR0_U_OFFSET(pin) ((pin - 16) * 2)
-#define GAFR1_L_OFFSET(pin) ((pin - 32) * 2)
-#define GAFR1_U_OFFSET(pin) ((pin - 48) * 2)
-#define GPDR1_OFFSET(pin) (pin - 32)
-#define GPCR1_OFFSET(pin) (pin - 32)
-#define GPSR1_OFFSET(pin) (pin - 32)
-#define GPCR0_OFFSET(pin) (pin)
-#define GPSR0_OFFSET(pin) (pin)
-
-static void am200_set_gpio_output(int pin, int val)
-{
-	u8 index;
-
-	index = pin >> 4;
-
-	switch (index) {
-	case 1:
-		if (val)
-			GPSR0 |= (1 << GPSR0_OFFSET(pin));
-		else
-			GPCR0 |= (1 << GPCR0_OFFSET(pin));
-		break;
-	case 2:
-		break;
-	case 3:
-		if (val)
-			GPSR1 |= (1 << GPSR1_OFFSET(pin));
-		else
-			GPCR1 |= (1 << GPCR1_OFFSET(pin));
-		break;
-	default:
-		printk(KERN_ERR "unimplemented\n");
-	}
-}
-
-static void __devinit am200_init_gpio_pin(int pin, int dir)
-{
-	u8 index;
-	/* dir 0 is output, 1 is input
-	- do 2 things here:
-	- set gpio alternate function to standard gpio
-	- set gpio direction to input or output  */
-
-	index = pin >> 4;
-	switch (index) {
-	case 1:
-		GAFR0_U &= ~(AF_SEL_GPIO_N << GAFR0_U_OFFSET(pin));
-
-		if (dir)
-			GPDR0 &= ~(1 << pin);
-		else
-			GPDR0 |= (1 << pin);
-		break;
-	case 2:
-		GAFR1_L &= ~(AF_SEL_GPIO_N << GAFR1_L_OFFSET(pin));
-
-		if (dir)
-			GPDR1 &= ~(1 << GPDR1_OFFSET(pin));
-		else
-			GPDR1 |= (1 << GPDR1_OFFSET(pin));
-		break;
-	case 3:
-		GAFR1_U &= ~(AF_SEL_GPIO_N << GAFR1_U_OFFSET(pin));
-
-		if (dir)
-			GPDR1 &= ~(1 << GPDR1_OFFSET(pin));
-		else
-			GPDR1 |= (1 << GPDR1_OFFSET(pin));
-		break;
-	default:
-		printk(KERN_ERR "unimplemented\n");
-	}
-}
-
-static void am200_init_gpio_regs(struct metronomefb_par *par)
-{
-	am200_init_gpio_pin(LED_GPIO_PIN, 0);
-	am200_set_gpio_output(LED_GPIO_PIN, 0);
-
-	am200_init_gpio_pin(STDBY_GPIO_PIN, 0);
-	am200_set_gpio_output(STDBY_GPIO_PIN, 0);
-
-	am200_init_gpio_pin(RST_GPIO_PIN, 0);
-	am200_set_gpio_output(RST_GPIO_PIN, 0);
-
-	am200_init_gpio_pin(RDY_GPIO_PIN, 1);
-
-	am200_init_gpio_pin(ERR_GPIO_PIN, 1);
-
-	am200_init_gpio_pin(PCBPWR_GPIO_PIN, 0);
-	am200_set_gpio_output(PCBPWR_GPIO_PIN, 0);
-}
-
-static void am200_disable_lcd_controller(struct metronomefb_par *par)
-{
-	LCSR = 0xffffffff;	/* Clear LCD Status Register */
-	LCCR0 |= LCCR0_DIS;	/* Disable LCD Controller */
-
-	/* we reset and just wait for things to settle */
-	msleep(200);
-}
-
-static void am200_enable_lcd_controller(struct metronomefb_par *par)
-{
-	LCSR = 0xffffffff;
-	FDADR0 = par->metromem_desc_dma;
-	LCCR0 |= LCCR0_ENB;
-}
-
-static void am200_init_lcdc_regs(struct metronomefb_par *par)
-{
-	/* here we do:
-	- disable the lcd controller
-	- setup lcd control registers
-	- setup dma descriptor
-	- reenable lcd controller
-	*/
-
-	/* disable the lcd controller */
-	am200_disable_lcd_controller(par);
-
-	/* setup lcd control registers */
-	LCCR0 = LCCR0_LDM | LCCR0_SFM | LCCR0_IUM | LCCR0_EFM | LCCR0_PAS
-		| LCCR0_QDM | LCCR0_BM | LCCR0_OUM;
-
-	LCCR1 = (par->info->var.xres/2 - 1) /* pixels per line */
-		| (27 << 10) /* hsync pulse width - 1 */
-		| (33 << 16) /* eol pixel count */
-		| (33 << 24); /* bol pixel count */
-
-	LCCR2 = (par->info->var.yres - 1) /* lines per panel */
-		| (24 << 10) /* vsync pulse width - 1 */
-		| (2 << 16) /* eof pixel count */
-		| (0 << 24); /* bof pixel count */
-
-	LCCR3 = 2 /* pixel clock divisor */
-		| (24 << 8) /* AC Bias pin freq */
-		| LCCR3_16BPP /* BPP */
-		| LCCR3_PCP;  /* PCP falling edge */
-
-}
-
-static void am200_post_dma_setup(struct metronomefb_par *par)
-{
-	par->metromem_desc->mFDADR0 = par->metromem_desc_dma;
-	par->metromem_desc->mFSADR0 = par->metromem_dma;
-	par->metromem_desc->mFIDR0 = 0;
-	par->metromem_desc->mLDCMD0 = par->info->var.xres
-					* par->info->var.yres;
-	am200_enable_lcd_controller(par);
-}
-
-static void am200_free_irq(struct fb_info *info)
-{
-	free_irq(IRQ_GPIO(RDY_GPIO_PIN), info);
-}
-
-static irqreturn_t am200_handle_irq(int irq, void *dev_id)
-{
-	struct fb_info *info = dev_id;
-	struct metronomefb_par *par = info->par;
-
-	wake_up_interruptible(&par->waitq);
-	return IRQ_HANDLED;
-}
-
-static int am200_setup_irq(struct fb_info *info)
-{
-	int retval;
-
-	retval = request_irq(IRQ_GPIO(RDY_GPIO_PIN), am200_handle_irq,
-				IRQF_DISABLED, "AM200", info);
-	if (retval) {
-		printk(KERN_ERR "am200epd: request_irq failed: %d\n", retval);
-		return retval;
-	}
-
-	return set_irq_type(IRQ_GPIO(RDY_GPIO_PIN), IRQT_FALLING);
-}
-
-static void am200_set_rst(struct metronomefb_par *par, int state)
-{
-	am200_set_gpio_output(RST_GPIO_PIN, state);
-}
-
-static void am200_set_stdby(struct metronomefb_par *par, int state)
-{
-	am200_set_gpio_output(STDBY_GPIO_PIN, state);
-}
-
-static int am200_wait_event(struct metronomefb_par *par)
-{
-	return wait_event_timeout(par->waitq, (GPLR1 & 0x01), HZ);
-}
-
-static int am200_wait_event_intr(struct metronomefb_par *par)
-{
-	return wait_event_interruptible_timeout(par->waitq, (GPLR1 & 0x01), HZ);
-}
-
-static struct metronome_board am200_board = {
-	.owner			= THIS_MODULE,
-	.free_irq		= am200_free_irq,
-	.setup_irq		= am200_setup_irq,
-	.init_gpio_regs		= am200_init_gpio_regs,
-	.init_lcdc_regs		= am200_init_lcdc_regs,
-	.post_dma_setup		= am200_post_dma_setup,
-	.set_rst		= am200_set_rst,
-	.set_stdby		= am200_set_stdby,
-	.met_wait_event		= am200_wait_event,
-	.met_wait_event_intr	= am200_wait_event_intr,
-};
-
-static struct platform_device *am200_device;
-
-static int __init am200_init(void)
-{
-	int ret;
-
-	/* request our platform independent driver */
-	request_module("metronomefb");
-
-	am200_device = platform_device_alloc("metronomefb", -1);
-	if (!am200_device)
-		return -ENOMEM;
-
-	platform_device_add_data(am200_device, &am200_board,
-					sizeof(am200_board));
-
-	/* this _add binds metronomefb to am200. metronomefb refcounts am200 */
-	ret = platform_device_add(am200_device);
-
-	if (ret)
-		platform_device_put(am200_device);
-
-	return ret;
-}
-
-static void __exit am200_exit(void)
-{
-	platform_device_unregister(am200_device);
-}
-
-module_init(am200_init);
-module_exit(am200_exit);
-
-MODULE_DESCRIPTION("board driver for am200 metronome epd kit");
-MODULE_AUTHOR("Jaya Kumar");
-MODULE_LICENSE("GPL");
-- 
1.5.3.6


-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft
Defy all challenges. Microsoft(R) Visual Studio 2008.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/