From: "Manjunathappa, Prakash" <prakash.pm@ti.com>
To: linux-fbdev@vger.kernel.org
Subject: [PATCH] da8xx-fb: save and restore LCDC context across suspend/resume cycle
Date: Tue, 25 Sep 2012 14:23:41 +0000 [thread overview]
Message-ID: <1348582301-27373-1-git-send-email-prakash.pm@ti.com> (raw)
Save and restore register context of LCDC respectively
before suspend and after resume.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
---
Applies on top of below patch under review:
"da8xx-fb: add pm_runtime support"
drivers/video/da8xx-fb.c | 65 ++++++++++++++++++++++++++++++++++++++++++++++
1 files changed, 65 insertions(+), 0 deletions(-)
diff --git a/drivers/video/da8xx-fb.c b/drivers/video/da8xx-fb.c
index 4280d23..65a11ef 100644
--- a/drivers/video/da8xx-fb.c
+++ b/drivers/video/da8xx-fb.c
@@ -1491,6 +1491,69 @@ err_request_mem:
}
#ifdef CONFIG_PM
+struct lcdc_context {
+ u32 clk_enable;
+ u32 ctrl;
+ u32 dma_ctrl;
+ u32 raster_timing_0;
+ u32 raster_timing_1;
+ u32 raster_timing_2;
+ u32 int_enable_set;
+ u32 dma_frm_buf_base_addr_0;
+ u32 dma_frm_buf_ceiling_addr_0;
+ u32 dma_frm_buf_base_addr_1;
+ u32 dma_frm_buf_ceiling_addr_1;
+ u32 raster_ctrl;
+} reg_context;
+
+static void lcd_context_save(void)
+{
+ if (lcd_revision = LCD_VERSION_2) {
+ reg_context.clk_enable = lcdc_read(LCD_CLK_ENABLE_REG);
+ reg_context.int_enable_set = lcdc_read(LCD_INT_ENABLE_SET_REG);
+ }
+
+ reg_context.ctrl = lcdc_read(LCD_CTRL_REG);
+ reg_context.dma_ctrl = lcdc_read(LCD_DMA_CTRL_REG);
+ reg_context.raster_timing_0 = lcdc_read(LCD_RASTER_TIMING_0_REG);
+ reg_context.raster_timing_1 = lcdc_read(LCD_RASTER_TIMING_1_REG);
+ reg_context.raster_timing_2 = lcdc_read(LCD_RASTER_TIMING_2_REG);
+ reg_context.dma_frm_buf_base_addr_0 + lcdc_read(LCD_DMA_FRM_BUF_BASE_ADDR_0_REG);
+ reg_context.dma_frm_buf_ceiling_addr_0 + lcdc_read(LCD_DMA_FRM_BUF_CEILING_ADDR_0_REG);
+ reg_context.dma_frm_buf_base_addr_1 + lcdc_read(LCD_DMA_FRM_BUF_BASE_ADDR_1_REG);
+ reg_context.dma_frm_buf_ceiling_addr_1 + lcdc_read(LCD_DMA_FRM_BUF_CEILING_ADDR_1_REG);
+ reg_context.raster_ctrl = lcdc_read(LCD_RASTER_CTRL_REG);
+ return;
+}
+
+static void lcd_context_restore(void)
+{
+ if (lcd_revision = LCD_VERSION_2) {
+ lcdc_write(reg_context.clk_enable, LCD_CLK_ENABLE_REG);
+ lcdc_write(reg_context.int_enable_set, LCD_INT_ENABLE_SET_REG);
+ }
+
+ lcdc_write(reg_context.ctrl, LCD_CTRL_REG);
+ lcdc_write(reg_context.dma_ctrl, LCD_DMA_CTRL_REG);
+ lcdc_write(reg_context.raster_timing_0, LCD_RASTER_TIMING_0_REG);
+ lcdc_write(reg_context.raster_timing_1, LCD_RASTER_TIMING_1_REG);
+ lcdc_write(reg_context.raster_timing_2, LCD_RASTER_TIMING_2_REG);
+ lcdc_write(reg_context.dma_frm_buf_base_addr_0,
+ LCD_DMA_FRM_BUF_BASE_ADDR_0_REG);
+ lcdc_write(reg_context.dma_frm_buf_ceiling_addr_0,
+ LCD_DMA_FRM_BUF_CEILING_ADDR_0_REG);
+ lcdc_write(reg_context.dma_frm_buf_base_addr_1,
+ LCD_DMA_FRM_BUF_BASE_ADDR_1_REG);
+ lcdc_write(reg_context.dma_frm_buf_ceiling_addr_1,
+ LCD_DMA_FRM_BUF_CEILING_ADDR_1_REG);
+ lcdc_write(reg_context.raster_ctrl, LCD_RASTER_CTRL_REG);
+ return;
+}
+
static int fb_suspend(struct platform_device *dev, pm_message_t state)
{
struct fb_info *info = platform_get_drvdata(dev);
@@ -1502,6 +1565,7 @@ static int fb_suspend(struct platform_device *dev, pm_message_t state)
fb_set_suspend(info, 1);
lcd_disable_raster(true);
+ lcd_context_save();
pm_runtime_put_sync(&dev->dev);
console_unlock();
@@ -1514,6 +1578,7 @@ static int fb_resume(struct platform_device *dev)
console_lock();
pm_runtime_get_sync(&dev->dev);
+ lcd_context_restore();
if (par->blank = FB_BLANK_UNBLANK) {
lcd_enable_raster();
--
1.7.0.4
next reply other threads:[~2012-09-25 14:23 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-09-25 14:23 Manjunathappa, Prakash [this message]
-- strict thread matches above, loose matches on Subject: below --
2012-10-10 12:33 [PATCH] da8xx-fb: save and restore LCDC context across suspend/resume cycle Florian Tobias Schandinat
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1348582301-27373-1-git-send-email-prakash.pm@ti.com \
--to=prakash.pm@ti.com \
--cc=linux-fbdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).