* [PATCH 1/6] video: vt8500: Make wmt_ge_rops optional
2013-03-27 8:46 [PATCH 0/6] fb: vt8500: patches for 3.10 Tony Prisk
@ 2013-03-27 8:46 ` Tony Prisk
2013-03-27 8:46 ` [PATCH 2/6] video: vt8500: Remove unused platform_data/video-vt8500lcdfb.h Tony Prisk
` (4 subsequent siblings)
5 siblings, 0 replies; 9+ messages in thread
From: Tony Prisk @ 2013-03-27 8:46 UTC (permalink / raw)
To: linux-arm-kernel
wmt_ge_rops is a seperate driver to vt8500/wm8505 framebuffer
driver but is currently a required option. This patch makes
accelerated raster ops optional.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
---
drivers/video/Kconfig | 22 ++++++++++++----------
drivers/video/vt8500lcdfb.c | 15 +++++++++++++++
drivers/video/wm8505fb.c | 15 +++++++++++++++
3 files changed, 42 insertions(+), 10 deletions(-)
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index 4c1546f..661aa54 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -212,14 +212,6 @@ config FB_SYS_FOPS
depends on FB
default n
-config FB_WMT_GE_ROPS
- tristate
- depends on FB
- default n
- ---help---
- Include functions for accelerated rectangle filling and area
- copying using WonderMedia Graphics Engine operations.
-
config FB_DEFERRED_IO
bool
depends on FB
@@ -1799,7 +1791,8 @@ config FB_AU1200
config FB_VT8500
bool "VT8500 LCD Driver"
depends on (FB = y) && ARM && ARCH_VT8500
- select FB_WMT_GE_ROPS
+ select FB_SYS_FILLRECT if (!FB_WMT_GE_ROPS)
+ select FB_SYS_COPYAREA if (!FB_WMT_GE_ROPS)
select FB_SYS_IMAGEBLIT
help
This is the framebuffer driver for VIA VT8500 integrated LCD
@@ -1808,12 +1801,21 @@ config FB_VT8500
config FB_WM8505
bool "WM8505 frame buffer support"
depends on (FB = y) && ARM && ARCH_VT8500
- select FB_WMT_GE_ROPS
+ select FB_SYS_FILLRECT if (!FB_WMT_GE_ROPS)
+ select FB_SYS_COPYAREA if (!FB_WMT_GE_ROPS)
select FB_SYS_IMAGEBLIT
help
This is the framebuffer driver for WonderMedia WM8505/WM8650
integrated LCD controller.
+config FB_WMT_GE_ROPS
+ bool "VT8500/WM85xx accelerated raster ops support"
+ depends on (FB = y) && (FB_VT8500 || FB_WM8505)
+ default n
+ help
+ This adds support for accelerated raster operations on the
+ VIA VT8500 and Wondermedia 85xx series SoCs.
+
source "drivers/video/geode/Kconfig"
config FB_HIT
diff --git a/drivers/video/vt8500lcdfb.c b/drivers/video/vt8500lcdfb.c
index aa2579c..d8cc1f6 100644
--- a/drivers/video/vt8500lcdfb.c
+++ b/drivers/video/vt8500lcdfb.c
@@ -33,7 +33,10 @@
#include <linux/platform_data/video-vt8500lcdfb.h>
#include "vt8500lcdfb.h"
+
+#ifdef CONFIG_FB_WMT_GE_ROPS
#include "wmt_ge_rops.h"
+#endif
#ifdef CONFIG_OF
#include <linux/of.h>
@@ -249,12 +252,24 @@ static int vt8500lcd_blank(int blank, struct fb_info *info)
return 0;
}
+#ifndef CONFIG_FB_WMT_GE_ROPS
+static int wmt_ge_sync(struct fb_info *p)
+{
+ return 0;
+}
+#endif
+
static struct fb_ops vt8500lcd_ops = {
.owner = THIS_MODULE,
.fb_set_par = vt8500lcd_set_par,
.fb_setcolreg = vt8500lcd_setcolreg,
+#ifdef CONFIG_FB_WMT_GE_ROPS
.fb_fillrect = wmt_ge_fillrect,
.fb_copyarea = wmt_ge_copyarea,
+#else
+ .fb_fillrect = sys_fillrect,
+ .fb_copyarea = sys_copyarea,
+#endif
.fb_imageblit = sys_imageblit,
.fb_sync = wmt_ge_sync,
.fb_ioctl = vt8500lcd_ioctl,
diff --git a/drivers/video/wm8505fb.c b/drivers/video/wm8505fb.c
index 4dd0580..db49803 100644
--- a/drivers/video/wm8505fb.c
+++ b/drivers/video/wm8505fb.c
@@ -35,7 +35,10 @@
#include <linux/platform_data/video-vt8500lcdfb.h>
#include "wm8505fb_regs.h"
+
+#ifdef CONFIG_FB_WMT_GE_ROPS
#include "wmt_ge_rops.h"
+#endif
#define DRIVER_NAME "wm8505-fb"
@@ -248,12 +251,24 @@ static int wm8505fb_blank(int blank, struct fb_info *info)
return 0;
}
+#ifndef CONFIG_FB_WMT_GE_ROPS
+static int wmt_ge_sync(struct fb_info *p)
+{
+ return 0;
+}
+#endif
+
static struct fb_ops wm8505fb_ops = {
.owner = THIS_MODULE,
.fb_set_par = wm8505fb_set_par,
.fb_setcolreg = wm8505fb_setcolreg,
+#ifdef CONFIG_FB_WMT_GE_ROPS
.fb_fillrect = wmt_ge_fillrect,
.fb_copyarea = wmt_ge_copyarea,
+#else
+ .fb_fillrect = sys_fillrect,
+ .fb_copyarea = sys_copyarea,
+#endif
.fb_imageblit = sys_imageblit,
.fb_sync = wmt_ge_sync,
.fb_pan_display = wm8505fb_pan_display,
--
1.7.9.5
^ permalink raw reply related [flat|nested] 9+ messages in thread* [PATCH 2/6] video: vt8500: Remove unused platform_data/video-vt8500lcdfb.h
2013-03-27 8:46 [PATCH 0/6] fb: vt8500: patches for 3.10 Tony Prisk
2013-03-27 8:46 ` [PATCH 1/6] video: vt8500: Make wmt_ge_rops optional Tony Prisk
@ 2013-03-27 8:46 ` Tony Prisk
2013-03-27 8:46 ` [PATCH 3/6] video: vt8500: Correct descriptions in video/Kconfig Tony Prisk
` (3 subsequent siblings)
5 siblings, 0 replies; 9+ messages in thread
From: Tony Prisk @ 2013-03-27 8:46 UTC (permalink / raw)
To: linux-arm-kernel
With the conversion to devicetree only for arch-vt8500, this
header is no longer required. This patch removes the #include
from the two framebuffer drivers that used it, and the header file.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
---
drivers/video/vt8500lcdfb.c | 2 --
drivers/video/wm8505fb.c | 2 --
include/linux/platform_data/video-vt8500lcdfb.h | 31 -----------------------
3 files changed, 35 deletions(-)
delete mode 100644 include/linux/platform_data/video-vt8500lcdfb.h
diff --git a/drivers/video/vt8500lcdfb.c b/drivers/video/vt8500lcdfb.c
index d8cc1f6..1c34821 100644
--- a/drivers/video/vt8500lcdfb.c
+++ b/drivers/video/vt8500lcdfb.c
@@ -30,8 +30,6 @@
#include <linux/platform_device.h>
#include <linux/wait.h>
-#include <linux/platform_data/video-vt8500lcdfb.h>
-
#include "vt8500lcdfb.h"
#ifdef CONFIG_FB_WMT_GE_ROPS
diff --git a/drivers/video/wm8505fb.c b/drivers/video/wm8505fb.c
index db49803..ce23a00 100644
--- a/drivers/video/wm8505fb.c
+++ b/drivers/video/wm8505fb.c
@@ -32,8 +32,6 @@
#include <linux/of_fdt.h>
#include <linux/memblock.h>
-#include <linux/platform_data/video-vt8500lcdfb.h>
-
#include "wm8505fb_regs.h"
#ifdef CONFIG_FB_WMT_GE_ROPS
diff --git a/include/linux/platform_data/video-vt8500lcdfb.h b/include/linux/platform_data/video-vt8500lcdfb.h
deleted file mode 100644
index 7f399c3..0000000
--- a/include/linux/platform_data/video-vt8500lcdfb.h
+++ /dev/null
@@ -1,31 +0,0 @@
-/*
- * VT8500/WM8505 Frame Buffer platform data definitions
- *
- * Copyright (C) 2010 Ed Spiridonov <edo.rus@gmail.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#ifndef _VT8500FB_H
-#define _VT8500FB_H
-
-#include <linux/fb.h>
-
-struct vt8500fb_platform_data {
- struct fb_videomode mode;
- u32 xres_virtual;
- u32 yres_virtual;
- u32 bpp;
- unsigned long video_mem_phys;
- void *video_mem_virt;
- unsigned long video_mem_len;
-};
-
-#endif /* _VT8500FB_H */
--
1.7.9.5
^ permalink raw reply related [flat|nested] 9+ messages in thread* [PATCH 3/6] video: vt8500: Correct descriptions in video/Kconfig
2013-03-27 8:46 [PATCH 0/6] fb: vt8500: patches for 3.10 Tony Prisk
2013-03-27 8:46 ` [PATCH 1/6] video: vt8500: Make wmt_ge_rops optional Tony Prisk
2013-03-27 8:46 ` [PATCH 2/6] video: vt8500: Remove unused platform_data/video-vt8500lcdfb.h Tony Prisk
@ 2013-03-27 8:46 ` Tony Prisk
2013-03-27 8:46 ` [PATCH 4/6] drivers/video/wm8505fb.c: use devm_ functions Tony Prisk
` (2 subsequent siblings)
5 siblings, 0 replies; 9+ messages in thread
From: Tony Prisk @ 2013-03-27 8:46 UTC (permalink / raw)
To: linux-arm-kernel
This patch corrects the descriptions for the VIA VT8500 and
Wondermedia WM8xxx-series framebuffer drivers to correctly reflect
which hardware they support.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
---
drivers/video/Kconfig | 11 ++++++-----
1 file changed, 6 insertions(+), 5 deletions(-)
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index 661aa54..ad762ed 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -1789,7 +1789,7 @@ config FB_AU1200
option au1200fb:panel=<name>.
config FB_VT8500
- bool "VT8500 LCD Driver"
+ bool "VIA VT8500 framebuffer support"
depends on (FB = y) && ARM && ARCH_VT8500
select FB_SYS_FILLRECT if (!FB_WMT_GE_ROPS)
select FB_SYS_COPYAREA if (!FB_WMT_GE_ROPS)
@@ -1799,17 +1799,18 @@ config FB_VT8500
controller.
config FB_WM8505
- bool "WM8505 frame buffer support"
+ bool "Wondermedia WM8xxx-series frame buffer support"
depends on (FB = y) && ARM && ARCH_VT8500
select FB_SYS_FILLRECT if (!FB_WMT_GE_ROPS)
select FB_SYS_COPYAREA if (!FB_WMT_GE_ROPS)
select FB_SYS_IMAGEBLIT
help
- This is the framebuffer driver for WonderMedia WM8505/WM8650
- integrated LCD controller.
+ This is the framebuffer driver for WonderMedia WM8xxx-series
+ integrated LCD controller. This driver covers the WM8505, WM8650
+ and WM8850 SoCs.
config FB_WMT_GE_ROPS
- bool "VT8500/WM85xx accelerated raster ops support"
+ bool "VT8500/WM8xxx accelerated raster ops support"
depends on (FB = y) && (FB_VT8500 || FB_WM8505)
default n
help
--
1.7.9.5
^ permalink raw reply related [flat|nested] 9+ messages in thread* [PATCH 4/6] drivers/video/wm8505fb.c: use devm_ functions
2013-03-27 8:46 [PATCH 0/6] fb: vt8500: patches for 3.10 Tony Prisk
` (2 preceding siblings ...)
2013-03-27 8:46 ` [PATCH 3/6] video: vt8500: Correct descriptions in video/Kconfig Tony Prisk
@ 2013-03-27 8:46 ` Tony Prisk
2013-03-27 8:47 ` [PATCH 5/6] video: vt8500: Adjust contrast in wm8505 framebuffer driver Tony Prisk
2013-03-27 8:47 ` [PATCH 6/6] video: fb: vt8500: Convert framebuffer drivers to standardized binding Tony Prisk
5 siblings, 0 replies; 9+ messages in thread
From: Tony Prisk @ 2013-03-27 8:46 UTC (permalink / raw)
To: linux-arm-kernel
From: Julia Lawall <Julia.Lawall@lip6.fr>
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
The patch makes some other cleanups. First, the original code used
devm_kzalloc, but kfree. This would lead to a double free. The problem
was found using the following semantic match (http://coccinelle.lip6.fr/):
// <smpl>
@@
expression x,e;
@@
x = devm_kzalloc(...)
... when != x = e
?-kfree(x,...);
// </smpl>
The error-handing code of devm_request_and_ioremap does not print any
warning message, because devm_request_and_ioremap does this.
The call to dma_alloc_coherent is converted to its devm equivalent,
dmam_alloc_coherent. This implicitly introduces a call to
dmam_free_coherent, which was completly missing in the original code.
A semicolon is removed at the end of the error-handling code for the call
to dma_alloc_coherent.
The block of code calling fb_alloc_cmap is moved below the block of code
calling wm8505fb_set_par, so that the error-handing code of the call to
wm8505fb_set_par can just return ret. This way there is only one block of
error-handling code that needs to call fb_dealloc_cmap, and so this is
moved up to the place where it is needed, eliminating the need for all
gotos and labels in the function. This was suggested by Tony Prisk.
The initializations of fbi and ret at the beginning of the function are not
necessary and are removed. The call platform_set_drvdata(pdev, NULL); at
the end of the function is also removed.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
---
drivers/video/wm8505fb.c | 79 +++++++++++-----------------------------------
1 file changed, 19 insertions(+), 60 deletions(-)
diff --git a/drivers/video/wm8505fb.c b/drivers/video/wm8505fb.c
index ce23a00..b94ebc9 100644
--- a/drivers/video/wm8505fb.c
+++ b/drivers/video/wm8505fb.c
@@ -287,15 +287,11 @@ static int wm8505fb_probe(struct platform_device *pdev)
unsigned long fb_mem_len;
void *fb_mem_virt;
- ret = -ENOMEM;
- fbi = NULL;
-
fbi = devm_kzalloc(&pdev->dev, sizeof(struct wm8505fb_info) +
sizeof(u32) * 16, GFP_KERNEL);
if (!fbi) {
dev_err(&pdev->dev, "Failed to initialize framebuffer device\n");
- ret = -ENOMEM;
- goto failed;
+ return -ENOMEM;
}
strcpy(fbi->fb.fix.id, DRIVER_NAME);
@@ -321,31 +317,14 @@ static int wm8505fb_probe(struct platform_device *pdev)
fbi->fb.pseudo_palette = addr;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- if (res = NULL) {
- dev_err(&pdev->dev, "no I/O memory resource defined\n");
- ret = -ENODEV;
- goto failed_fbi;
- }
-
- res = request_mem_region(res->start, resource_size(res), DRIVER_NAME);
- if (res = NULL) {
- dev_err(&pdev->dev, "failed to request I/O memory\n");
- ret = -EBUSY;
- goto failed_fbi;
- }
-
- fbi->regbase = ioremap(res->start, resource_size(res));
- if (fbi->regbase = NULL) {
- dev_err(&pdev->dev, "failed to map I/O memory\n");
- ret = -EBUSY;
- goto failed_free_res;
- }
+ fbi->regbase = devm_request_and_ioremap(&pdev->dev, res);
+ if (fbi->regbase = NULL)
+ return -EBUSY;
np = of_parse_phandle(pdev->dev.of_node, "default-mode", 0);
if (!np) {
pr_err("%s: No display description in Device Tree\n", __func__);
- ret = -EINVAL;
- goto failed_free_res;
+ return -EINVAL;
}
/*
@@ -364,7 +343,7 @@ static int wm8505fb_probe(struct platform_device *pdev)
ret |= of_property_read_u32(np, "bpp", &bpp);
if (ret) {
pr_err("%s: Unable to read display properties\n", __func__);
- goto failed_free_res;
+ return -EINVAL;
}
of_mode.vmode = FB_VMODE_NONINTERLACED;
@@ -378,12 +357,12 @@ static int wm8505fb_probe(struct platform_device *pdev)
/* try allocating the framebuffer */
fb_mem_len = of_mode.xres * of_mode.yres * 2 * (bpp / 8);
- fb_mem_virt = dma_alloc_coherent(&pdev->dev, fb_mem_len, &fb_mem_phys,
+ fb_mem_virt = dmam_alloc_coherent(&pdev->dev, fb_mem_len, &fb_mem_phys,
GFP_KERNEL);
if (!fb_mem_virt) {
pr_err("%s: Failed to allocate framebuffer\n", __func__);
return -ENOMEM;
- };
+ }
fbi->fb.var.xres_virtual = of_mode.xres;
fbi->fb.var.yres_virtual = of_mode.yres * 2;
@@ -394,28 +373,29 @@ static int wm8505fb_probe(struct platform_device *pdev)
fbi->fb.screen_base = fb_mem_virt;
fbi->fb.screen_size = fb_mem_len;
- if (fb_alloc_cmap(&fbi->fb.cmap, 256, 0) < 0) {
- dev_err(&pdev->dev, "Failed to allocate color map\n");
- ret = -ENOMEM;
- goto failed_free_io;
- }
-
- wm8505fb_init_hw(&fbi->fb);
-
fbi->contrast = 0x80;
ret = wm8505fb_set_par(&fbi->fb);
if (ret) {
dev_err(&pdev->dev, "Failed to set parameters\n");
- goto failed_free_cmap;
+ return ret;
}
+ if (fb_alloc_cmap(&fbi->fb.cmap, 256, 0) < 0) {
+ dev_err(&pdev->dev, "Failed to allocate color map\n");
+ return -ENOMEM;
+ }
+
+ wm8505fb_init_hw(&fbi->fb);
+
platform_set_drvdata(pdev, fbi);
ret = register_framebuffer(&fbi->fb);
if (ret < 0) {
dev_err(&pdev->dev,
"Failed to register framebuffer device: %d\n", ret);
- goto failed_free_cmap;
+ if (fbi->fb.cmap.len)
+ fb_dealloc_cmap(&fbi->fb.cmap);
+ return ret;
}
ret = device_create_file(&pdev->dev, &dev_attr_contrast);
@@ -429,25 +409,11 @@ static int wm8505fb_probe(struct platform_device *pdev)
fbi->fb.fix.smem_start + fbi->fb.fix.smem_len - 1);
return 0;
-
-failed_free_cmap:
- if (fbi->fb.cmap.len)
- fb_dealloc_cmap(&fbi->fb.cmap);
-failed_free_io:
- iounmap(fbi->regbase);
-failed_free_res:
- release_mem_region(res->start, resource_size(res));
-failed_fbi:
- platform_set_drvdata(pdev, NULL);
- kfree(fbi);
-failed:
- return ret;
}
static int wm8505fb_remove(struct platform_device *pdev)
{
struct wm8505fb_info *fbi = platform_get_drvdata(pdev);
- struct resource *res;
device_remove_file(&pdev->dev, &dev_attr_contrast);
@@ -458,13 +424,6 @@ static int wm8505fb_remove(struct platform_device *pdev)
if (fbi->fb.cmap.len)
fb_dealloc_cmap(&fbi->fb.cmap);
- iounmap(fbi->regbase);
-
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- release_mem_region(res->start, resource_size(res));
-
- kfree(fbi);
-
return 0;
}
--
1.7.9.5
^ permalink raw reply related [flat|nested] 9+ messages in thread* [PATCH 5/6] video: vt8500: Adjust contrast in wm8505 framebuffer driver.
2013-03-27 8:46 [PATCH 0/6] fb: vt8500: patches for 3.10 Tony Prisk
` (3 preceding siblings ...)
2013-03-27 8:46 ` [PATCH 4/6] drivers/video/wm8505fb.c: use devm_ functions Tony Prisk
@ 2013-03-27 8:47 ` Tony Prisk
2013-03-27 8:47 ` [PATCH 6/6] video: fb: vt8500: Convert framebuffer drivers to standardized binding Tony Prisk
5 siblings, 0 replies; 9+ messages in thread
From: Tony Prisk @ 2013-03-27 8:47 UTC (permalink / raw)
To: linux-arm-kernel
The contrast value was typo'd on the original commit (0x80 instead of
0x08). Following feedback from an enduser, a value of 0x10 seems more
suitable due to the default backlight being <100%.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
---
drivers/video/wm8505fb.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/video/wm8505fb.c b/drivers/video/wm8505fb.c
index b94ebc9..5057457 100644
--- a/drivers/video/wm8505fb.c
+++ b/drivers/video/wm8505fb.c
@@ -373,7 +373,7 @@ static int wm8505fb_probe(struct platform_device *pdev)
fbi->fb.screen_base = fb_mem_virt;
fbi->fb.screen_size = fb_mem_len;
- fbi->contrast = 0x80;
+ fbi->contrast = 0x10;
ret = wm8505fb_set_par(&fbi->fb);
if (ret) {
dev_err(&pdev->dev, "Failed to set parameters\n");
--
1.7.9.5
^ permalink raw reply related [flat|nested] 9+ messages in thread* [PATCH 6/6] video: fb: vt8500: Convert framebuffer drivers to standardized binding
2013-03-27 8:46 [PATCH 0/6] fb: vt8500: patches for 3.10 Tony Prisk
` (4 preceding siblings ...)
2013-03-27 8:47 ` [PATCH 5/6] video: vt8500: Adjust contrast in wm8505 framebuffer driver Tony Prisk
@ 2013-03-27 8:47 ` Tony Prisk
2013-03-27 11:10 ` Tomi Valkeinen
5 siblings, 1 reply; 9+ messages in thread
From: Tony Prisk @ 2013-03-27 8:47 UTC (permalink / raw)
To: linux-arm-kernel
Now that a display timing binding is available, convert our almost identical
binding to use the standard binding.
This patch converts the vt8500 and wm8505 framebuffer drivers and
associated dts/dtsi files to use the standard binding as defined in
bindings/video/display-timing.txt.
There are two side-effects of making this conversion:
1) The fb node should now be in the board file, rather than the soc file as
the display-timing node is a child of the fb node.
2) We still require a bits per pixel property to initialize the framebuffer
for the different lcd panels. Rather than including this as part of the
display timing, it is moved into the framebuffer node.
I have also taken the opportunity to alphabetise the includes of each
driver to avoid double-ups.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
---
.../devicetree/bindings/video/via,vt8500-fb.txt | 48 ++++----------
.../devicetree/bindings/video/wm,wm8505-fb.txt | 32 +++++----
arch/arm/boot/dts/vt8500-bv07.dts | 24 +++----
arch/arm/boot/dts/vt8500.dtsi | 8 ---
arch/arm/boot/dts/wm8505-ref.dts | 21 +++---
arch/arm/boot/dts/wm8505.dtsi | 7 --
arch/arm/boot/dts/wm8650-mid.dts | 21 +++---
arch/arm/boot/dts/wm8650.dtsi | 7 --
arch/arm/boot/dts/wm8850-w70v2.dts | 21 +++---
arch/arm/boot/dts/wm8850.dtsi | 7 --
drivers/video/Kconfig | 6 ++
drivers/video/vt8500lcdfb.c | 53 ++++++---------
drivers/video/wm8505fb.c | 68 ++++++++------------
13 files changed, 130 insertions(+), 193 deletions(-)
diff --git a/Documentation/devicetree/bindings/video/via,vt8500-fb.txt b/Documentation/devicetree/bindings/video/via,vt8500-fb.txt
index c870b64..2871e21 100644
--- a/Documentation/devicetree/bindings/video/via,vt8500-fb.txt
+++ b/Documentation/devicetree/bindings/video/via,vt8500-fb.txt
@@ -5,58 +5,32 @@ Required properties:
- compatible : "via,vt8500-fb"
- reg : Should contain 1 register ranges(address and length)
- interrupts : framebuffer controller interrupt
-- display: a phandle pointing to the display node
+- bits-per-pixel : bit depth of framebuffer (16 or 32)
-Required nodes:
-- display: a display node is required to initialize the lcd panel
- This should be in the board dts.
-- default-mode: a videomode within the display with timing parameters
- as specified below.
+Required subnodes:
+- display-timings: see display-timing.txt for information
Example:
- fb@d800e400 {
+ fb@d8050800 {
compatible = "via,vt8500-fb";
reg = <0xd800e400 0x400>;
interrupts = <12>;
- display = <&display>;
- default-mode = <&mode0>;
- };
-
-VIA VT8500 Display
------------------------------------------------------
-Required properties (as per of_videomode_helper):
-
- - hactive, vactive: Display resolution
- - hfront-porch, hback-porch, hsync-len: Horizontal Display timing parameters
- in pixels
- vfront-porch, vback-porch, vsync-len: Vertical display timing parameters in
- lines
- - clock: displayclock in Hz
- - bpp: lcd panel bit-depth.
- <16> for RGB565, <32> for RGB888
-
-Optional properties (as per of_videomode_helper):
- - width-mm, height-mm: Display dimensions in mm
- - hsync-active-high (bool): Hsync pulse is active high
- - vsync-active-high (bool): Vsync pulse is active high
- - interlaced (bool): This is an interlaced mode
- - doublescan (bool): This is a doublescan mode
+ bits-per-pixel = <16>;
-Example:
- display: display@0 {
- modes {
- mode0: mode@0 {
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: 800x480 {
+ clock-frequency = <0>; /* unused but required */
hactive = <800>;
vactive = <480>;
- hback-porch = <88>;
hfront-porch = <40>;
+ hback-porch = <88>;
hsync-len = <0>;
vback-porch = <32>;
vfront-porch = <11>;
vsync-len = <1>;
- clock = <0>; /* unused but required */
- bpp = <16>; /* non-standard but required */
};
};
};
+
diff --git a/Documentation/devicetree/bindings/video/wm,wm8505-fb.txt b/Documentation/devicetree/bindings/video/wm,wm8505-fb.txt
index 3d325e1..0bcadb2 100644
--- a/Documentation/devicetree/bindings/video/wm,wm8505-fb.txt
+++ b/Documentation/devicetree/bindings/video/wm,wm8505-fb.txt
@@ -4,20 +4,30 @@ Wondermedia WM8505 Framebuffer
Required properties:
- compatible : "wm,wm8505-fb"
- reg : Should contain 1 register ranges(address and length)
-- via,display: a phandle pointing to the display node
+- bits-per-pixel : bit depth of framebuffer (16 or 32)
-Required nodes:
-- display: a display node is required to initialize the lcd panel
- This should be in the board dts. See definition in
- Documentation/devicetree/bindings/video/via,vt8500-fb.txt
-- default-mode: a videomode node as specified in
- Documentation/devicetree/bindings/video/via,vt8500-fb.txt
+Required subnodes:
+- display-timings: see display-timing.txt for information
Example:
- fb@d8050800 {
+ fb@d8051700 {
compatible = "wm,wm8505-fb";
- reg = <0xd8050800 0x200>;
- display = <&display>;
- default-mode = <&mode0>;
+ reg = <0xd8051700 0x200>;
+ bits-per-pixel = <16>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: 800x480 {
+ clock-frequency = <0>; /* unused but required */
+ hactive = <800>;
+ vactive = <480>;
+ hfront-porch = <40>;
+ hback-porch = <88>;
+ hsync-len = <0>;
+ vback-porch = <32>;
+ vfront-porch = <11>;
+ vsync-len = <1>;
+ };
+ };
};
diff --git a/arch/arm/boot/dts/vt8500-bv07.dts b/arch/arm/boot/dts/vt8500-bv07.dts
index 567cf4e..7ec9a41 100644
--- a/arch/arm/boot/dts/vt8500-bv07.dts
+++ b/arch/arm/boot/dts/vt8500-bv07.dts
@@ -12,24 +12,26 @@
/ {
model = "Benign BV07 Netbook";
- /*
- * Display node is based on Sascha Hauer's patch on dri-devel.
- * Added a bpp property to calculate the size of the framebuffer
- * until the binding is formalized.
- */
- display: display@0 {
- modes {
- mode0: mode@0 {
+ interrupt-parent = <&intc>;
+
+ fb@d8050800 {
+ compatible = "via,vt8500-fb";
+ reg = <0xd800e400 0x400>;
+ interrupts = <12>;
+ bits-per-pixel = <16>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: 800x480 {
+ clock-frequency = <0>; /* unused but required */
hactive = <800>;
vactive = <480>;
- hback-porch = <88>;
hfront-porch = <40>;
+ hback-porch = <88>;
hsync-len = <0>;
vback-porch = <32>;
vfront-porch = <11>;
vsync-len = <1>;
- clock = <0>; /* unused but required */
- bpp = <16>; /* non-standard but required */
};
};
};
diff --git a/arch/arm/boot/dts/vt8500.dtsi b/arch/arm/boot/dts/vt8500.dtsi
index cf31ced..fc25d9f 100644
--- a/arch/arm/boot/dts/vt8500.dtsi
+++ b/arch/arm/boot/dts/vt8500.dtsi
@@ -98,14 +98,6 @@
interrupts = <43>;
};
- fb@d800e400 {
- compatible = "via,vt8500-fb";
- reg = <0xd800e400 0x400>;
- interrupts = <12>;
- display = <&display>;
- default-mode = <&mode0>;
- };
-
ge_rops@d8050400 {
compatible = "wm,prizm-ge-rops";
reg = <0xd8050400 0x100>;
diff --git a/arch/arm/boot/dts/wm8505-ref.dts b/arch/arm/boot/dts/wm8505-ref.dts
index fd4e248..a600572 100644
--- a/arch/arm/boot/dts/wm8505-ref.dts
+++ b/arch/arm/boot/dts/wm8505-ref.dts
@@ -12,24 +12,23 @@
/ {
model = "Wondermedia WM8505 Netbook";
- /*
- * Display node is based on Sascha Hauer's patch on dri-devel.
- * Added a bpp property to calculate the size of the framebuffer
- * until the binding is formalized.
- */
- display: display@0 {
- modes {
- mode0: mode@0 {
+ fb@d8050800 {
+ compatible = "wm,wm8505-fb";
+ reg = <0xd8050800 0x200>;
+ bits-per-pixel = <32>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: 800x480 {
+ clock-frequency = <0>; /* unused but required */
hactive = <800>;
vactive = <480>;
- hback-porch = <88>;
hfront-porch = <40>;
+ hback-porch = <88>;
hsync-len = <0>;
vback-porch = <32>;
vfront-porch = <11>;
vsync-len = <1>;
- clock = <0>; /* unused but required */
- bpp = <32>; /* non-standard but required */
};
};
};
diff --git a/arch/arm/boot/dts/wm8505.dtsi b/arch/arm/boot/dts/wm8505.dtsi
index e74a1c0..826bd8d 100644
--- a/arch/arm/boot/dts/wm8505.dtsi
+++ b/arch/arm/boot/dts/wm8505.dtsi
@@ -128,13 +128,6 @@
interrupts = <0>;
};
- fb@d8050800 {
- compatible = "wm,wm8505-fb";
- reg = <0xd8050800 0x200>;
- display = <&display>;
- default-mode = <&mode0>;
- };
-
ge_rops@d8050400 {
compatible = "wm,prizm-ge-rops";
reg = <0xd8050400 0x100>;
diff --git a/arch/arm/boot/dts/wm8650-mid.dts b/arch/arm/boot/dts/wm8650-mid.dts
index cefd938..d77bf22 100644
--- a/arch/arm/boot/dts/wm8650-mid.dts
+++ b/arch/arm/boot/dts/wm8650-mid.dts
@@ -12,24 +12,23 @@
/ {
model = "Wondermedia WM8650-MID Tablet";
- /*
- * Display node is based on Sascha Hauer's patch on dri-devel.
- * Added a bpp property to calculate the size of the framebuffer
- * until the binding is formalized.
- */
- display: display@0 {
- modes {
- mode0: mode@0 {
+ fb@d8050800 {
+ compatible = "wm,wm8505-fb";
+ reg = <0xd8050800 0x200>;
+ bits-per-pixel = <16>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: 800x480 {
+ clock-frequency = <0>; /* unused but required */
hactive = <800>;
vactive = <480>;
- hback-porch = <88>;
hfront-porch = <40>;
+ hback-porch = <88>;
hsync-len = <0>;
vback-porch = <32>;
vfront-porch = <11>;
vsync-len = <1>;
- clock = <0>; /* unused but required */
- bpp = <16>; /* non-standard but required */
};
};
};
diff --git a/arch/arm/boot/dts/wm8650.dtsi b/arch/arm/boot/dts/wm8650.dtsi
index db3c0a1..2073963 100644
--- a/arch/arm/boot/dts/wm8650.dtsi
+++ b/arch/arm/boot/dts/wm8650.dtsi
@@ -128,13 +128,6 @@
interrupts = <43>;
};
- fb@d8050800 {
- compatible = "wm,wm8505-fb";
- reg = <0xd8050800 0x200>;
- display = <&display>;
- default-mode = <&mode0>;
- };
-
ge_rops@d8050400 {
compatible = "wm,prizm-ge-rops";
reg = <0xd8050400 0x100>;
diff --git a/arch/arm/boot/dts/wm8850-w70v2.dts b/arch/arm/boot/dts/wm8850-w70v2.dts
index fcc660c..9b56701 100644
--- a/arch/arm/boot/dts/wm8850-w70v2.dts
+++ b/arch/arm/boot/dts/wm8850-w70v2.dts
@@ -15,24 +15,23 @@
/ {
model = "Wondermedia WM8850-W70v2 Tablet";
- /*
- * Display node is based on Sascha Hauer's patch on dri-devel.
- * Added a bpp property to calculate the size of the framebuffer
- * until the binding is formalized.
- */
- display: display@0 {
- modes {
- mode0: mode@0 {
+ fb@d8051700 {
+ compatible = "wm,wm8505-fb";
+ reg = <0xd8051700 0x200>;
+ bits-per-pixel = <16>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: 800x480 {
+ clock-frequency = <0>; /* unused but required */
hactive = <800>;
vactive = <480>;
- hback-porch = <88>;
hfront-porch = <40>;
+ hback-porch = <88>;
hsync-len = <0>;
vback-porch = <32>;
vfront-porch = <11>;
vsync-len = <1>;
- clock = <0>; /* unused but required */
- bpp = <16>; /* non-standard but required */
};
};
};
diff --git a/arch/arm/boot/dts/wm8850.dtsi b/arch/arm/boot/dts/wm8850.dtsi
index e8cbfdc..dfc50a4 100644
--- a/arch/arm/boot/dts/wm8850.dtsi
+++ b/arch/arm/boot/dts/wm8850.dtsi
@@ -135,13 +135,6 @@
};
};
- fb@d8051700 {
- compatible = "wm,wm8505-fb";
- reg = <0xd8051700 0x200>;
- display = <&display>;
- default-mode = <&mode0>;
- };
-
ge_rops@d8050400 {
compatible = "wm,prizm-ge-rops";
reg = <0xd8050400 0x100>;
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index ad762ed..d0c932a 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -1794,6 +1794,9 @@ config FB_VT8500
select FB_SYS_FILLRECT if (!FB_WMT_GE_ROPS)
select FB_SYS_COPYAREA if (!FB_WMT_GE_ROPS)
select FB_SYS_IMAGEBLIT
+ select FB_MODE_HELPERS
+ select OF_DISPLAY_TIMING
+ select OF_VIDEOMODE
help
This is the framebuffer driver for VIA VT8500 integrated LCD
controller.
@@ -1804,6 +1807,9 @@ config FB_WM8505
select FB_SYS_FILLRECT if (!FB_WMT_GE_ROPS)
select FB_SYS_COPYAREA if (!FB_WMT_GE_ROPS)
select FB_SYS_IMAGEBLIT
+ select FB_MODE_HELPERS
+ select OF_DISPLAY_TIMING
+ select OF_VIDEOMODE
help
This is the framebuffer driver for WonderMedia WM8xxx-series
integrated LCD controller. This driver covers the WM8505, WM8650
diff --git a/drivers/video/vt8500lcdfb.c b/drivers/video/vt8500lcdfb.c
index 1c34821..816e8ce 100644
--- a/drivers/video/vt8500lcdfb.c
+++ b/drivers/video/vt8500lcdfb.c
@@ -15,20 +15,21 @@
* GNU General Public License for more details.
*/
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/errno.h>
-#include <linux/string.h>
-#include <linux/mm.h>
-#include <linux/slab.h>
#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/errno.h>
#include <linux/fb.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/io.h>
-#include <linux/dma-mapping.h>
+#include <linux/kernel.h>
+#include <linux/mm.h>
+#include <linux/module.h>
#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/string.h>
#include <linux/wait.h>
+#include <video/of_display_timing.h>
#include "vt8500lcdfb.h"
@@ -290,11 +291,11 @@ static int vt8500lcd_probe(struct platform_device *pdev)
{
struct vt8500lcd_info *fbi;
struct resource *res;
+ struct display_timings *disp_timing;
void *addr;
int irq, ret;
struct fb_videomode of_mode;
- struct device_node *np;
u32 bpp;
dma_addr_t fb_mem_phys;
unsigned long fb_mem_len;
@@ -359,31 +360,19 @@ static int vt8500lcd_probe(struct platform_device *pdev)
goto failed_free_res;
}
- np = of_parse_phandle(pdev->dev.of_node, "default-mode", 0);
- if (!np) {
- pr_err("%s: No display description in Device Tree\n", __func__);
- ret = -EINVAL;
- goto failed_free_res;
- }
+ disp_timing = of_get_display_timings(pdev->dev.of_node);
+ if (!disp_timing)
+ return -EINVAL;
+
+ ret = of_get_fb_videomode(pdev->dev.of_node, &of_mode,
+ OF_USE_NATIVE_MODE);
+ if (ret)
+ return ret;
+
+ ret = of_property_read_u32(pdev->dev.of_node, "bits-per-pixel", &bpp);
+ if (ret)
+ return ret;
- /*
- * This code is copied from Sascha Hauer's of_videomode helper
- * and can be replaced with a call to the helper once mainlined
- */
- ret = 0;
- ret |= of_property_read_u32(np, "hactive", &of_mode.xres);
- ret |= of_property_read_u32(np, "vactive", &of_mode.yres);
- ret |= of_property_read_u32(np, "hback-porch", &of_mode.left_margin);
- ret |= of_property_read_u32(np, "hfront-porch", &of_mode.right_margin);
- ret |= of_property_read_u32(np, "hsync-len", &of_mode.hsync_len);
- ret |= of_property_read_u32(np, "vback-porch", &of_mode.upper_margin);
- ret |= of_property_read_u32(np, "vfront-porch", &of_mode.lower_margin);
- ret |= of_property_read_u32(np, "vsync-len", &of_mode.vsync_len);
- ret |= of_property_read_u32(np, "bpp", &bpp);
- if (ret) {
- pr_err("%s: Unable to read display properties\n", __func__);
- goto failed_free_res;
- }
of_mode.vmode = FB_VMODE_NONINTERLACED;
/* try allocating the framebuffer */
diff --git a/drivers/video/wm8505fb.c b/drivers/video/wm8505fb.c
index 5057457..ab112ad 100644
--- a/drivers/video/wm8505fb.c
+++ b/drivers/video/wm8505fb.c
@@ -14,23 +14,24 @@
* GNU General Public License for more details.
*/
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/errno.h>
-#include <linux/string.h>
-#include <linux/mm.h>
-#include <linux/slab.h>
#include <linux/delay.h>
+#include <linux/dma-mapping.h>
#include <linux/fb.h>
+#include <linux/errno.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/io.h>
-#include <linux/dma-mapping.h>
-#include <linux/platform_device.h>
-#include <linux/wait.h>
+#include <linux/kernel.h>
+#include <linux/memblock.h>
+#include <linux/mm.h>
+#include <linux/module.h>
#include <linux/of.h>
#include <linux/of_fdt.h>
-#include <linux/memblock.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/string.h>
+#include <linux/wait.h>
+#include <video/of_display_timing.h>
#include "wm8505fb_regs.h"
@@ -276,12 +277,12 @@ static struct fb_ops wm8505fb_ops = {
static int wm8505fb_probe(struct platform_device *pdev)
{
struct wm8505fb_info *fbi;
- struct resource *res;
+ struct resource *res;
+ struct display_timings *disp_timing;
void *addr;
int ret;
- struct fb_videomode of_mode;
- struct device_node *np;
+ struct fb_videomode mode;
u32 bpp;
dma_addr_t fb_mem_phys;
unsigned long fb_mem_len;
@@ -321,33 +322,20 @@ static int wm8505fb_probe(struct platform_device *pdev)
if (fbi->regbase = NULL)
return -EBUSY;
- np = of_parse_phandle(pdev->dev.of_node, "default-mode", 0);
- if (!np) {
- pr_err("%s: No display description in Device Tree\n", __func__);
+ disp_timing = of_get_display_timings(pdev->dev.of_node);
+ if (!disp_timing)
return -EINVAL;
- }
- /*
- * This code is copied from Sascha Hauer's of_videomode helper
- * and can be replaced with a call to the helper once mainlined
- */
- ret = 0;
- ret |= of_property_read_u32(np, "hactive", &of_mode.xres);
- ret |= of_property_read_u32(np, "vactive", &of_mode.yres);
- ret |= of_property_read_u32(np, "hback-porch", &of_mode.left_margin);
- ret |= of_property_read_u32(np, "hfront-porch", &of_mode.right_margin);
- ret |= of_property_read_u32(np, "hsync-len", &of_mode.hsync_len);
- ret |= of_property_read_u32(np, "vback-porch", &of_mode.upper_margin);
- ret |= of_property_read_u32(np, "vfront-porch", &of_mode.lower_margin);
- ret |= of_property_read_u32(np, "vsync-len", &of_mode.vsync_len);
- ret |= of_property_read_u32(np, "bpp", &bpp);
- if (ret) {
- pr_err("%s: Unable to read display properties\n", __func__);
- return -EINVAL;
- }
+ ret = of_get_fb_videomode(pdev->dev.of_node, &mode, OF_USE_NATIVE_MODE);
+ if (ret)
+ return ret;
+
+ ret = of_property_read_u32(pdev->dev.of_node, "bits-per-pixel", &bpp);
+ if (ret)
+ return ret;
- of_mode.vmode = FB_VMODE_NONINTERLACED;
- fb_videomode_to_var(&fbi->fb.var, &of_mode);
+ mode.vmode = FB_VMODE_NONINTERLACED;
+ fb_videomode_to_var(&fbi->fb.var, &mode);
fbi->fb.var.nonstd = 0;
fbi->fb.var.activate = FB_ACTIVATE_NOW;
@@ -356,7 +344,7 @@ static int wm8505fb_probe(struct platform_device *pdev)
fbi->fb.var.width = -1;
/* try allocating the framebuffer */
- fb_mem_len = of_mode.xres * of_mode.yres * 2 * (bpp / 8);
+ fb_mem_len = mode.xres * mode.yres * 2 * (bpp / 8);
fb_mem_virt = dmam_alloc_coherent(&pdev->dev, fb_mem_len, &fb_mem_phys,
GFP_KERNEL);
if (!fb_mem_virt) {
@@ -364,8 +352,8 @@ static int wm8505fb_probe(struct platform_device *pdev)
return -ENOMEM;
}
- fbi->fb.var.xres_virtual = of_mode.xres;
- fbi->fb.var.yres_virtual = of_mode.yres * 2;
+ fbi->fb.var.xres_virtual = mode.xres;
+ fbi->fb.var.yres_virtual = mode.yres * 2;
fbi->fb.var.bits_per_pixel = bpp;
fbi->fb.fix.smem_start = fb_mem_phys;
--
1.7.9.5
^ permalink raw reply related [flat|nested] 9+ messages in thread* Re: [PATCH 6/6] video: fb: vt8500: Convert framebuffer drivers to standardized binding
2013-03-27 8:47 ` [PATCH 6/6] video: fb: vt8500: Convert framebuffer drivers to standardized binding Tony Prisk
@ 2013-03-27 11:10 ` Tomi Valkeinen
2013-03-28 5:04 ` Tony Prisk
0 siblings, 1 reply; 9+ messages in thread
From: Tomi Valkeinen @ 2013-03-27 11:10 UTC (permalink / raw)
To: linux-arm-kernel
[-- Attachment #1: Type: text/plain, Size: 1717 bytes --]
Hi,
On 2013-03-27 10:47, Tony Prisk wrote:
> Now that a display timing binding is available, convert our almost identical
> binding to use the standard binding.
>
> This patch converts the vt8500 and wm8505 framebuffer drivers and
> associated dts/dtsi files to use the standard binding as defined in
> bindings/video/display-timing.txt.
>
> There are two side-effects of making this conversion:
>
> 1) The fb node should now be in the board file, rather than the soc file as
> the display-timing node is a child of the fb node.
>
> 2) We still require a bits per pixel property to initialize the framebuffer
> for the different lcd panels. Rather than including this as part of the
> display timing, it is moved into the framebuffer node.
>
> I have also taken the opportunity to alphabetise the includes of each
> driver to avoid double-ups.
I don't think this is correct. I don't have that much experience with
DT, but I think you should have, for example:
wm8850.dtsi:
fb: fb@d8051700 {
compatible = "wm,wm8505-fb";
reg = <0xd8051700 0x200>;
};
wm8850-w70v2.dts:
&fb {
bits-per-pixel = <16>;
display-timings {
native-mode = <&timing0>;
timing0: 800x480 {
clock-frequency = <0>;
...
};
};
};
So, the core fb part should be in the SoC's file, as it's part of the
SoC. And the stuff that tells what kind of display is attached is in the
board dts file.
Also, just a word of warning, I think the videomode series I've sent for
review will cause some breakage with this series if the videomode series
is accepted. Nothing difficult to fix, though, but we'll need some extra
management to avoid compilation failures.
Tomi
[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 899 bytes --]
^ permalink raw reply [flat|nested] 9+ messages in thread* Re: [PATCH 6/6] video: fb: vt8500: Convert framebuffer drivers to standardized binding
2013-03-27 11:10 ` Tomi Valkeinen
@ 2013-03-28 5:04 ` Tony Prisk
0 siblings, 0 replies; 9+ messages in thread
From: Tony Prisk @ 2013-03-28 5:04 UTC (permalink / raw)
To: linux-arm-kernel
On Wed, 2013-03-27 at 13:10 +0200, Tomi Valkeinen wrote:
> Hi,
>
> On 2013-03-27 10:47, Tony Prisk wrote:
> > Now that a display timing binding is available, convert our almost identical
> > binding to use the standard binding.
> >
> > This patch converts the vt8500 and wm8505 framebuffer drivers and
> > associated dts/dtsi files to use the standard binding as defined in
> > bindings/video/display-timing.txt.
> >
> > There are two side-effects of making this conversion:
> >
> > 1) The fb node should now be in the board file, rather than the soc file as
> > the display-timing node is a child of the fb node.
> >
> > 2) We still require a bits per pixel property to initialize the framebuffer
> > for the different lcd panels. Rather than including this as part of the
> > display timing, it is moved into the framebuffer node.
> >
> > I have also taken the opportunity to alphabetise the includes of each
> > driver to avoid double-ups.
>
> I don't think this is correct. I don't have that much experience with
> DT, but I think you should have, for example:
>
> wm8850.dtsi:
>
> fb: fb@d8051700 {
> compatible = "wm,wm8505-fb";
> reg = <0xd8051700 0x200>;
> };
>
> wm8850-w70v2.dts:
>
> &fb {
> bits-per-pixel = <16>;
>
> display-timings {
> native-mode = <&timing0>;
> timing0: 800x480 {
> clock-frequency = <0>;
> ...
> };
> };
> };
>
> So, the core fb part should be in the SoC's file, as it's part of the
> SoC. And the stuff that tells what kind of display is attached is in the
> board dts file.
>
> Also, just a word of warning, I think the videomode series I've sent for
> review will cause some breakage with this series if the videomode series
> is accepted. Nothing difficult to fix, though, but we'll need some extra
> management to avoid compilation failures.
>
> Tomi
>
>
Thanks for the feedback and the heads-up.
I believe you are correct about the DT info - it looks right when
described the way you did, so I have changed it.
If there is no other feedback, I will post a version 2 after Easter.
Regards
Tony P
^ permalink raw reply [flat|nested] 9+ messages in thread