* [PATCH V5 2/4] backlight: qcom-wled: Add callback functions
[not found] <1586274430-28402-1-git-send-email-kgunda@codeaurora.org>
@ 2020-04-07 15:59 ` Kiran Gunda
2020-04-20 16:17 ` Daniel Thompson
2020-04-07 15:59 ` [PATCH V5 4/4] backlight: qcom-wled: Add support for WLED5 peripheral that is present on PM8150L PMI Kiran Gunda
1 sibling, 1 reply; 4+ messages in thread
From: Kiran Gunda @ 2020-04-07 15:59 UTC (permalink / raw)
To: bjorn.andersson, jingoohan1, lee.jones, b.zolnierkie, dri-devel,
daniel.thompson, jacek.anaszewski, pavel, robh+dt, mark.rutland,
linux-leds, devicetree, linux-kernel, Andy Gross, linux-arm-msm,
linux-fbdev
Cc: Subbaraman Narayanamurthy, Kiran Gunda
Add wled_cabc_config, wled_sync_toggle, wled_ovp_fault_status
and wled_ovp_delay and wled_auto_detection_required callback
functions to prepare the driver for adding WLED5 support.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
---
drivers/video/backlight/qcom-wled.c | 216 ++++++++++++++++++++++++------------
1 file changed, 144 insertions(+), 72 deletions(-)
diff --git a/drivers/video/backlight/qcom-wled.c b/drivers/video/backlight/qcom-wled.c
index 3d276b3..a6ddaa9 100644
--- a/drivers/video/backlight/qcom-wled.c
+++ b/drivers/video/backlight/qcom-wled.c
@@ -147,6 +147,7 @@ struct wled {
u32 max_brightness;
u32 short_count;
u32 auto_detect_count;
+ u32 version;
bool disabled_by_short;
bool has_short_detect;
int short_irq;
@@ -154,7 +155,33 @@ struct wled {
struct wled_config cfg;
struct delayed_work ovp_work;
+
+ /* Configures the brightness. Applicable for wled3, wled4 and wled5 */
int (*wled_set_brightness)(struct wled *wled, u16 brightness);
+
+ /* Configures the cabc register. Applicable for wled4 and wled5 */
+ int (*wled_cabc_config)(struct wled *wled, bool enable);
+
+ /*
+ * Toggles the sync bit for the brightness update to take place.
+ * Applicable for WLED3, WLED4 and WLED5.
+ */
+ int (*wled_sync_toggle)(struct wled *wled);
+
+ /* Determines OVP fault status. Applicable for WLED4 and WLED5 */
+ int (*wled_ovp_fault_status)(struct wled *wled, bool *fault_set);
+
+ /*
+ * Time to wait before checking the OVP status after wled module enable.
+ * Applicable for WLED4 and WLED5.
+ */
+ int (*wled_ovp_delay)(struct wled *wled);
+
+ /*
+ * Determines if the auto string detection is required.
+ * Applicable for WLED4 and WLED5
+ */
+ bool (*wled_auto_detection_required)(struct wled *wled);
};
static int wled3_set_brightness(struct wled *wled, u16 brightness)
@@ -237,7 +264,7 @@ static int wled_module_enable(struct wled *wled, int val)
return 0;
}
-static int wled_sync_toggle(struct wled *wled)
+static int wled3_sync_toggle(struct wled *wled)
{
int rc;
unsigned int mask = GENMASK(wled->max_string_count - 1, 0);
@@ -255,6 +282,46 @@ static int wled_sync_toggle(struct wled *wled)
return rc;
}
+static int wled4_ovp_fault_status(struct wled *wled, bool *fault_set)
+{
+ int rc;
+ u32 int_rt_sts, fault_sts;
+
+ *fault_set = false;
+ rc = regmap_read(wled->regmap,
+ wled->ctrl_addr + WLED3_CTRL_REG_INT_RT_STS,
+ &int_rt_sts);
+ if (rc < 0) {
+ dev_err(wled->dev, "Failed to read INT_RT_STS rc=%d\n", rc);
+ return rc;
+ }
+
+ rc = regmap_read(wled->regmap,
+ wled->ctrl_addr + WLED3_CTRL_REG_FAULT_STATUS,
+ &fault_sts);
+ if (rc < 0) {
+ dev_err(wled->dev, "Failed to read FAULT_STATUS rc=%d\n", rc);
+ return rc;
+ }
+
+ if (int_rt_sts & WLED3_CTRL_REG_OVP_FAULT_STATUS)
+ *fault_set = true;
+
+ if (fault_sts & WLED3_CTRL_REG_OVP_FAULT_BIT)
+ *fault_set = true;
+
+ if (*fault_set)
+ dev_dbg(wled->dev, "WLED OVP fault detected, int_rt_sts=0x%x fault_sts=0x%x\n",
+ int_rt_sts, fault_sts);
+
+ return rc;
+}
+
+static int wled4_ovp_delay(struct wled *wled)
+{
+ return WLED_SOFT_START_DLY_US;
+}
+
static int wled_update_status(struct backlight_device *bl)
{
struct wled *wled = bl_get_data(bl);
@@ -275,7 +342,7 @@ static int wled_update_status(struct backlight_device *bl)
goto unlock_mutex;
}
- rc = wled_sync_toggle(wled);
+ rc = wled->wled_sync_toggle(wled);
if (rc < 0) {
dev_err(wled->dev, "wled sync failed rc:%d\n", rc);
goto unlock_mutex;
@@ -298,6 +365,25 @@ static int wled_update_status(struct backlight_device *bl)
return rc;
}
+static int wled4_cabc_config(struct wled *wled, bool enable)
+{
+ int i, j, rc;
+ u8 val;
+
+ for (i = 0; i < wled->cfg.num_strings; i++) {
+ j = wled->cfg.enabled_strings[i];
+
+ val = enable ? WLED4_SINK_REG_STR_CABC_MASK : 0;
+ rc = regmap_update_bits(wled->regmap, wled->sink_addr +
+ WLED4_SINK_REG_STR_CABC(j),
+ WLED4_SINK_REG_STR_CABC_MASK, val);
+ if (rc < 0)
+ return rc;
+ }
+
+ return 0;
+}
+
#define WLED_SHORT_DLY_MS 20
#define WLED_SHORT_CNT_MAX 5
#define WLED_SHORT_RESET_CNT_DLY_US USEC_PER_SEC
@@ -345,9 +431,10 @@ static irqreturn_t wled_short_irq_handler(int irq, void *_wled)
static void wled_auto_string_detection(struct wled *wled)
{
- int rc = 0, i;
- u32 sink_config = 0, int_sts;
+ int rc = 0, i, delay_time_us;
+ u32 sink_config = 0;
u8 sink_test = 0, sink_valid = 0, val;
+ bool fault_set;
/* Read configured sink configuration */
rc = regmap_read(wled->regmap, wled->sink_addr +
@@ -376,14 +463,9 @@ static void wled_auto_string_detection(struct wled *wled)
}
if (wled->cfg.cabc) {
- for (i = 0; i < wled->cfg.num_strings; i++) {
- rc = regmap_update_bits(wled->regmap, wled->sink_addr +
- WLED4_SINK_REG_STR_CABC(i),
- WLED4_SINK_REG_STR_CABC_MASK,
- 0);
- if (rc < 0)
- goto failed_detect;
- }
+ rc = wled->wled_cabc_config(wled, false);
+ if (rc < 0)
+ goto failed_detect;
}
/* Disable all sinks */
@@ -427,18 +509,17 @@ static void wled_auto_string_detection(struct wled *wled)
goto failed_detect;
}
- usleep_range(WLED_SOFT_START_DLY_US,
- WLED_SOFT_START_DLY_US + 1000);
+ delay_time_us = wled->wled_ovp_delay(wled);
+ usleep_range(delay_time_us, delay_time_us + 1000);
- rc = regmap_read(wled->regmap, wled->ctrl_addr +
- WLED3_CTRL_REG_INT_RT_STS, &int_sts);
+ rc = wled->wled_ovp_fault_status(wled, &fault_set);
if (rc < 0) {
- dev_err(wled->dev, "Error in reading WLED3_CTRL_INT_RT_STS rc=%d\n",
+ dev_err(wled->dev, "Error in getting OVP fault_sts, rc=%d\n",
rc);
goto failed_detect;
}
- if (int_sts & WLED3_CTRL_REG_OVP_FAULT_STATUS)
+ if (fault_set)
dev_dbg(wled->dev, "WLED OVP fault detected with SINK %d\n",
i + 1);
else
@@ -478,30 +559,30 @@ static void wled_auto_string_detection(struct wled *wled)
}
/* Enable valid sinks */
- for (i = 0; i < wled->cfg.num_strings; i++) {
- if (wled->cfg.cabc) {
- rc = regmap_update_bits(wled->regmap, wled->sink_addr +
- WLED4_SINK_REG_STR_CABC(i),
- WLED4_SINK_REG_STR_CABC_MASK,
- WLED4_SINK_REG_STR_CABC_MASK);
- if (rc < 0)
+ if (wled->version = 4) {
+ for (i = 0; i < wled->cfg.num_strings; i++) {
+ if (sink_config &
+ BIT(WLED4_SINK_REG_CURR_SINK_SHFT + i))
+ val = WLED4_SINK_REG_STR_MOD_MASK;
+ else
+ /* Disable modulator_en for unused sink */
+ val = 0;
+
+ rc = regmap_write(wled->regmap, wled->sink_addr +
+ WLED4_SINK_REG_STR_MOD_EN(i), val);
+ if (rc < 0) {
+ dev_err(wled->dev, "Failed to configure MODULATOR_EN rc=%d\n",
+ rc);
goto failed_detect;
- }
-
- if (sink_config & BIT(WLED4_SINK_REG_CURR_SINK_SHFT + i))
- val = WLED4_SINK_REG_STR_MOD_MASK;
- else
- val = 0x0; /* Disable modulator_en for unused sink */
-
- rc = regmap_write(wled->regmap, wled->sink_addr +
- WLED4_SINK_REG_STR_MOD_EN(i), val);
- if (rc < 0) {
- dev_err(wled->dev, "Failed to configure MODULATOR_EN rc=%d\n",
- rc);
- goto failed_detect;
+ }
}
}
+ /* Enable CABC */
+ rc = wled->wled_cabc_config(wled, true);
+ if (rc < 0)
+ goto failed_detect;
+
/* Restore the feedback setting */
rc = regmap_write(wled->regmap,
wled->ctrl_addr + WLED3_CTRL_REG_FEEDBACK_CONTROL, 0);
@@ -534,7 +615,7 @@ static void wled_auto_string_detection(struct wled *wled)
#define WLED_AUTO_DETECT_OVP_COUNT 5
#define WLED_AUTO_DETECT_CNT_DLY_US USEC_PER_SEC
-static bool wled_auto_detection_required(struct wled *wled)
+static bool wled4_auto_detection_required(struct wled *wled)
{
s64 elapsed_time_us;
@@ -570,29 +651,19 @@ static bool wled_auto_detection_required(struct wled *wled)
static int wled_auto_detection_at_init(struct wled *wled)
{
int rc;
- u32 fault_status, rt_status;
+ bool fault_set;
if (!wled->cfg.auto_detection_enabled)
return 0;
- rc = regmap_read(wled->regmap,
- wled->ctrl_addr + WLED3_CTRL_REG_INT_RT_STS,
- &rt_status);
- if (rc < 0) {
- dev_err(wled->dev, "Failed to read RT status rc=%d\n", rc);
- return rc;
- }
-
- rc = regmap_read(wled->regmap,
- wled->ctrl_addr + WLED3_CTRL_REG_FAULT_STATUS,
- &fault_status);
+ rc = wled->wled_ovp_fault_status(wled, &fault_set);
if (rc < 0) {
- dev_err(wled->dev, "Failed to read fault status rc=%d\n", rc);
+ dev_err(wled->dev, "Error in getting OVP fault_sts, rc=%d\n",
+ rc);
return rc;
}
- if ((rt_status & WLED3_CTRL_REG_OVP_FAULT_STATUS) ||
- (fault_status & WLED3_CTRL_REG_OVP_FAULT_BIT)) {
+ if (fault_set) {
mutex_lock(&wled->lock);
wled_auto_string_detection(wled);
mutex_unlock(&wled->lock);
@@ -629,7 +700,7 @@ static irqreturn_t wled_ovp_irq_handler(int irq, void *_wled)
int_sts, fault_sts);
if (fault_sts & WLED3_CTRL_REG_OVP_FAULT_BIT) {
- if (wled_auto_detection_required(wled)) {
+ if (wled->wled_auto_detection_required(wled)) {
mutex_lock(&wled->lock);
wled_auto_string_detection(wled);
mutex_unlock(&wled->lock);
@@ -811,17 +882,12 @@ static int wled4_setup(struct wled *wled)
wled->cfg.string_i_limit);
if (rc < 0)
return rc;
-
- addr = wled->sink_addr +
- WLED4_SINK_REG_STR_CABC(j);
- rc = regmap_update_bits(wled->regmap, addr,
- WLED4_SINK_REG_STR_CABC_MASK,
- wled->cfg.cabc ?
- WLED4_SINK_REG_STR_CABC_MASK : 0);
- if (rc < 0)
- return rc;
}
+ rc = wled4_cabc_config(wled, wled->cfg.cabc);
+ if (rc < 0)
+ return rc;
+
rc = regmap_update_bits(wled->regmap, wled->ctrl_addr +
WLED3_CTRL_REG_MOD_EN,
WLED3_CTRL_REG_MOD_EN_MASK,
@@ -835,7 +901,7 @@ static int wled4_setup(struct wled *wled)
if (rc < 0)
return rc;
- rc = wled_sync_toggle(wled);
+ rc = wled->wled_sync_toggle(wled);
if (rc < 0) {
dev_err(wled->dev, "Failed to toggle sync reg rc:%d\n", rc);
return rc;
@@ -951,7 +1017,7 @@ static u32 wled_values(const struct wled_var_cfg *cfg, u32 idx)
return idx;
}
-static int wled_configure(struct wled *wled, int version)
+static int wled_configure(struct wled *wled)
{
struct wled_config *cfg = &wled->cfg;
struct device *dev = wled->dev;
@@ -1035,12 +1101,13 @@ static int wled_configure(struct wled *wled, int version)
if (rc)
wled->name = devm_kasprintf(dev, GFP_KERNEL, "%pOFn", dev->of_node);
- switch (version) {
+ switch (wled->version) {
case 3:
u32_opts = wled3_opts;
size = ARRAY_SIZE(wled3_opts);
*cfg = wled3_config_defaults;
wled->wled_set_brightness = wled3_set_brightness;
+ wled->wled_sync_toggle = wled3_sync_toggle;
wled->max_string_count = 3;
wled->sink_addr = wled->ctrl_addr;
break;
@@ -1050,6 +1117,12 @@ static int wled_configure(struct wled *wled, int version)
size = ARRAY_SIZE(wled4_opts);
*cfg = wled4_config_defaults;
wled->wled_set_brightness = wled4_set_brightness;
+ wled->wled_sync_toggle = wled3_sync_toggle;
+ wled->wled_cabc_config = wled4_cabc_config;
+ wled->wled_ovp_fault_status = wled4_ovp_fault_status;
+ wled->wled_ovp_delay = wled4_ovp_delay;
+ wled->wled_auto_detection_required + wled4_auto_detection_required;
wled->max_string_count = 4;
prop_addr = of_get_address(dev->of_node, 1, NULL, NULL);
@@ -1186,7 +1259,6 @@ static int wled_probe(struct platform_device *pdev)
struct backlight_device *bl;
struct wled *wled;
struct regmap *regmap;
- int version;
u32 val;
int rc;
@@ -1203,18 +1275,18 @@ static int wled_probe(struct platform_device *pdev)
wled->regmap = regmap;
wled->dev = &pdev->dev;
- version = (uintptr_t)of_device_get_match_data(&pdev->dev);
- if (!version) {
+ wled->version = (uintptr_t)of_device_get_match_data(&pdev->dev);
+ if (!wled->version) {
dev_err(&pdev->dev, "Unknown device version\n");
return -ENODEV;
}
mutex_init(&wled->lock);
- rc = wled_configure(wled, version);
+ rc = wled_configure(wled);
if (rc)
return rc;
- switch (version) {
+ switch (wled->version) {
case 3:
wled->cfg.auto_detection_enabled = false;
rc = wled3_setup(wled);
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related [flat|nested] 4+ messages in thread* [PATCH V5 4/4] backlight: qcom-wled: Add support for WLED5 peripheral that is present on PM8150L PMI
[not found] <1586274430-28402-1-git-send-email-kgunda@codeaurora.org>
2020-04-07 15:59 ` [PATCH V5 2/4] backlight: qcom-wled: Add callback functions Kiran Gunda
@ 2020-04-07 15:59 ` Kiran Gunda
2020-04-20 16:37 ` [PATCH V5 4/4] backlight: qcom-wled: Add support for WLED5 peripheral that is present on PM8150L Daniel Thompson
1 sibling, 1 reply; 4+ messages in thread
From: Kiran Gunda @ 2020-04-07 15:59 UTC (permalink / raw)
To: bjorn.andersson, jingoohan1, lee.jones, b.zolnierkie, dri-devel,
daniel.thompson, jacek.anaszewski, pavel, robh+dt, mark.rutland,
linux-leds, devicetree, linux-kernel, Andy Gross, linux-arm-msm,
linux-fbdev
Cc: Subbaraman Narayanamurthy, Kiran Gunda
From: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
PM8150L WLED supports the following:
- Two modulators and each sink can use any of the modulator
- Multiple CABC selection options from which one can be selected/enabled
- Multiple brightness width selection (12 bits to 15 bits)
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
---
drivers/video/backlight/qcom-wled.c | 443 +++++++++++++++++++++++++++++++++++-
1 file changed, 442 insertions(+), 1 deletion(-)
diff --git a/drivers/video/backlight/qcom-wled.c b/drivers/video/backlight/qcom-wled.c
index a6ddaa9..3a57011 100644
--- a/drivers/video/backlight/qcom-wled.c
+++ b/drivers/video/backlight/qcom-wled.c
@@ -19,12 +19,15 @@
#define WLED_DEFAULT_BRIGHTNESS 2048
#define WLED_SOFT_START_DLY_US 10000
#define WLED3_SINK_REG_BRIGHT_MAX 0xFFF
+#define WLED5_SINK_REG_BRIGHT_MAX_12B 0xFFF
+#define WLED5_SINK_REG_BRIGHT_MAX_15B 0x7FFF
/* WLED3/WLED4 control registers */
#define WLED3_CTRL_REG_FAULT_STATUS 0x08
#define WLED3_CTRL_REG_ILIM_FAULT_BIT BIT(0)
#define WLED3_CTRL_REG_OVP_FAULT_BIT BIT(1)
#define WLED4_CTRL_REG_SC_FAULT_BIT BIT(2)
+#define WLED5_CTRL_REG_OVP_PRE_ALARM_BIT BIT(4)
#define WLED3_CTRL_REG_INT_RT_STS 0x10
#define WLED3_CTRL_REG_OVP_FAULT_STATUS BIT(1)
@@ -40,6 +43,7 @@
#define WLED3_CTRL_REG_OVP 0x4d
#define WLED3_CTRL_REG_OVP_MASK GENMASK(1, 0)
+#define WLED5_CTRL_REG_OVP_MASK GENMASK(3, 0)
#define WLED3_CTRL_REG_ILIMIT 0x4e
#define WLED3_CTRL_REG_ILIMIT_MASK GENMASK(2, 0)
@@ -101,6 +105,44 @@
#define WLED4_SINK_REG_BRIGHT(n) (0x57 + (n * 0x10))
+/* WLED5 specific control registers */
+#define WLED5_CTRL_REG_OVP_INT_CTL 0x5f
+#define WLED5_CTRL_REG_OVP_INT_TIMER_MASK GENMASK(2, 0)
+
+/* WLED5 specific sink registers */
+#define WLED5_SINK_REG_MOD_A_EN 0x50
+#define WLED5_SINK_REG_MOD_B_EN 0x60
+#define WLED5_SINK_REG_MOD_EN_MASK BIT(7)
+
+#define WLED5_SINK_REG_MOD_A_SRC_SEL 0x51
+#define WLED5_SINK_REG_MOD_B_SRC_SEL 0x61
+#define WLED5_SINK_REG_MOD_SRC_SEL_HIGH 0
+#define WLED5_SINK_REG_MOD_SRC_SEL_EXT 0x03
+#define WLED5_SINK_REG_MOD_SRC_SEL_MASK GENMASK(1, 0)
+
+#define WLED5_SINK_REG_MOD_A_BRIGHTNESS_WIDTH_SEL 0x52
+#define WLED5_SINK_REG_MOD_B_BRIGHTNESS_WIDTH_SEL 0x62
+#define WLED5_SINK_REG_BRIGHTNESS_WIDTH_12B 0
+#define WLED5_SINK_REG_BRIGHTNESS_WIDTH_15B 1
+
+#define WLED5_SINK_REG_MOD_A_BRIGHTNESS_LSB 0x53
+#define WLED5_SINK_REG_MOD_A_BRIGHTNESS_MSB 0x54
+#define WLED5_SINK_REG_MOD_B_BRIGHTNESS_LSB 0x63
+#define WLED5_SINK_REG_MOD_B_BRIGHTNESS_MSB 0x64
+
+#define WLED5_SINK_REG_MOD_SYNC_BIT 0x65
+#define WLED5_SINK_REG_SYNC_MOD_A_BIT BIT(0)
+#define WLED5_SINK_REG_SYNC_MOD_B_BIT BIT(1)
+#define WLED5_SINK_REG_SYNC_MASK GENMASK(1, 0)
+
+/* WLED5 specific per-'string' registers below */
+#define WLED5_SINK_REG_STR_FULL_SCALE_CURR(n) (0x72 + (n * 0x10))
+
+#define WLED5_SINK_REG_STR_SRC_SEL(n) (0x73 + (n * 0x10))
+#define WLED5_SINK_REG_SRC_SEL_MOD_A 0
+#define WLED5_SINK_REG_SRC_SEL_MOD_B 1
+#define WLED5_SINK_REG_SRC_SEL_MASK GENMASK(1, 0)
+
struct wled_var_cfg {
const u32 *values;
u32 (*fn)(u32);
@@ -125,6 +167,8 @@ struct wled_config {
u32 num_strings;
u32 string_i_limit;
u32 enabled_strings[WLED_MAX_STRINGS];
+ u32 mod_sel;
+ u32 cabc_sel;
bool cs_out_en;
bool ext_gen;
bool cabc;
@@ -150,6 +194,7 @@ struct wled {
u32 version;
bool disabled_by_short;
bool has_short_detect;
+ bool cabc_disabled;
int short_irq;
int ovp_irq;
@@ -184,6 +229,27 @@ struct wled {
bool (*wled_auto_detection_required)(struct wled *wled);
};
+enum wled5_mod_sel {
+ MOD_A,
+ MOD_B,
+ MOD_MAX,
+};
+
+static const u8 wled5_brightness_reg[MOD_MAX] = {
+ [MOD_A] = WLED5_SINK_REG_MOD_A_BRIGHTNESS_LSB,
+ [MOD_B] = WLED5_SINK_REG_MOD_B_BRIGHTNESS_LSB,
+};
+
+static const u8 wled5_src_sel_reg[MOD_MAX] = {
+ [MOD_A] = WLED5_SINK_REG_MOD_A_SRC_SEL,
+ [MOD_B] = WLED5_SINK_REG_MOD_B_SRC_SEL,
+};
+
+static const u8 wled5_brt_wid_sel_reg[MOD_MAX] = {
+ [MOD_A] = WLED5_SINK_REG_MOD_A_BRIGHTNESS_WIDTH_SEL,
+ [MOD_B] = WLED5_SINK_REG_MOD_B_BRIGHTNESS_WIDTH_SEL,
+};
+
static int wled3_set_brightness(struct wled *wled, u16 brightness)
{
int rc, i;
@@ -225,6 +291,25 @@ static int wled4_set_brightness(struct wled *wled, u16 brightness)
return 0;
}
+static int wled5_set_brightness(struct wled *wled, u16 brightness)
+{
+ int rc, offset;
+ u16 low_limit = wled->max_brightness * 1 / 1000;
+ u8 v[2];
+
+ /* WLED5's lower limit is 0.1% */
+ if (brightness < low_limit)
+ brightness = low_limit;
+
+ v[0] = brightness & 0xff;
+ v[1] = (brightness >> 8) & 0x7f;
+
+ offset = wled5_brightness_reg[wled->cfg.mod_sel];
+ rc = regmap_bulk_write(wled->regmap, wled->sink_addr + offset,
+ v, 2);
+ return rc;
+}
+
static void wled_ovp_work(struct work_struct *work)
{
struct wled *wled = container_of(work,
@@ -282,6 +367,24 @@ static int wled3_sync_toggle(struct wled *wled)
return rc;
}
+static int wled5_sync_toggle(struct wled *wled)
+{
+ int rc;
+ u8 val;
+
+ val = (wled->cfg.mod_sel = MOD_A) ? WLED5_SINK_REG_SYNC_MOD_A_BIT :
+ WLED5_SINK_REG_SYNC_MOD_B_BIT;
+ rc = regmap_update_bits(wled->regmap,
+ wled->sink_addr + WLED5_SINK_REG_MOD_SYNC_BIT,
+ WLED5_SINK_REG_SYNC_MASK, val);
+ if (rc < 0)
+ return rc;
+
+ return regmap_update_bits(wled->regmap,
+ wled->sink_addr + WLED5_SINK_REG_MOD_SYNC_BIT,
+ WLED5_SINK_REG_SYNC_MASK, 0);
+}
+
static int wled4_ovp_fault_status(struct wled *wled, bool *fault_set)
{
int rc;
@@ -317,11 +420,67 @@ static int wled4_ovp_fault_status(struct wled *wled, bool *fault_set)
return rc;
}
+static int wled5_ovp_fault_status(struct wled *wled, bool *fault_set)
+{
+ int rc;
+ u32 int_rt_sts, fault_sts;
+
+ *fault_set = false;
+ rc = regmap_read(wled->regmap,
+ wled->ctrl_addr + WLED3_CTRL_REG_INT_RT_STS,
+ &int_rt_sts);
+ if (rc < 0) {
+ dev_err(wled->dev, "Failed to read INT_RT_STS rc=%d\n", rc);
+ return rc;
+ }
+
+ rc = regmap_read(wled->regmap,
+ wled->ctrl_addr + WLED3_CTRL_REG_FAULT_STATUS,
+ &fault_sts);
+ if (rc < 0) {
+ dev_err(wled->dev, "Failed to read FAULT_STATUS rc=%d\n", rc);
+ return rc;
+ }
+
+ if (int_rt_sts & WLED3_CTRL_REG_OVP_FAULT_STATUS)
+ *fault_set = true;
+
+ if (fault_sts & (WLED3_CTRL_REG_OVP_FAULT_BIT |
+ WLED5_CTRL_REG_OVP_PRE_ALARM_BIT))
+ *fault_set = true;
+
+ if (*fault_set)
+ dev_dbg(wled->dev, "WLED OVP fault detected, int_rt_sts=0x%x fault_sts=0x%x\n",
+ int_rt_sts, fault_sts);
+
+ return rc;
+}
+
static int wled4_ovp_delay(struct wled *wled)
{
return WLED_SOFT_START_DLY_US;
}
+static int wled5_ovp_delay(struct wled *wled)
+{
+ int rc, delay_us;
+ u32 val;
+ u8 ovp_timer_ms[8] = {1, 2, 4, 8, 12, 16, 20, 24};
+
+ /* For WLED5, get the delay based on OVP timer */
+ rc = regmap_read(wled->regmap, wled->ctrl_addr +
+ WLED5_CTRL_REG_OVP_INT_CTL, &val);
+ if (rc < 0)
+ delay_us + ovp_timer_ms[val & WLED5_CTRL_REG_OVP_INT_TIMER_MASK] * 1000;
+ else
+ delay_us = 2 * WLED_SOFT_START_DLY_US;
+
+ dev_dbg(wled->dev, "delay_time_us: %d\n", delay_us);
+
+ return delay_us;
+}
+
static int wled_update_status(struct backlight_device *bl)
{
struct wled *wled = bl_get_data(bl);
@@ -384,6 +543,29 @@ static int wled4_cabc_config(struct wled *wled, bool enable)
return 0;
}
+static int wled5_cabc_config(struct wled *wled, bool enable)
+{
+ int rc, offset;
+ u8 reg;
+
+ if (wled->cabc_disabled)
+ return 0;
+
+ reg = enable ? wled->cfg.cabc_sel : 0;
+ offset = wled5_src_sel_reg[wled->cfg.mod_sel];
+ rc = regmap_update_bits(wled->regmap, wled->sink_addr + offset,
+ WLED5_SINK_REG_MOD_SRC_SEL_MASK, reg);
+ if (rc < 0) {
+ pr_err("Error in configuring CABC rc=%d\n", rc);
+ return rc;
+ }
+
+ if (!wled->cfg.cabc_sel)
+ wled->cabc_disabled = true;
+
+ return 0;
+}
+
#define WLED_SHORT_DLY_MS 20
#define WLED_SHORT_CNT_MAX 5
#define WLED_SHORT_RESET_CNT_DLY_US USEC_PER_SEC
@@ -615,6 +797,7 @@ static void wled_auto_string_detection(struct wled *wled)
#define WLED_AUTO_DETECT_OVP_COUNT 5
#define WLED_AUTO_DETECT_CNT_DLY_US USEC_PER_SEC
+
static bool wled4_auto_detection_required(struct wled *wled)
{
s64 elapsed_time_us;
@@ -648,6 +831,46 @@ static bool wled4_auto_detection_required(struct wled *wled)
return false;
}
+static bool wled5_auto_detection_required(struct wled *wled)
+{
+ s64 elapsed_time_us;
+
+ if (!wled->cfg.auto_detection_enabled)
+ return false;
+
+ /*
+ * Check if the OVP fault was an occasional one
+ * or if it's firing continuously, the latter qualifies
+ * for an auto-detection check.
+ */
+ if (!wled->auto_detection_ovp_count) {
+ wled->start_ovp_fault_time = ktime_get();
+ wled->auto_detection_ovp_count++;
+ } else {
+ /*
+ * WLED5 has OVP fault density interrupt configuration i.e. to
+ * count the number of OVP alarms for a certain duration before
+ * triggering OVP fault interrupt. By default, number of OVP
+ * fault events counted before an interrupt is fired is 32 and
+ * the time interval is 12 ms. If we see more than one OVP fault
+ * interrupt, then that should qualify for a real OVP fault
+ * condition to run auto calibration algorithm.
+ */
+
+ if (wled->auto_detection_ovp_count > 1) {
+ elapsed_time_us = ktime_us_delta(ktime_get(),
+ wled->start_ovp_fault_time);
+ wled->auto_detection_ovp_count = 0;
+ dev_dbg(wled->dev, "Elapsed time: %lld us\n",
+ elapsed_time_us);
+ return true;
+ }
+ wled->auto_detection_ovp_count++;
+ }
+
+ return false;
+}
+
static int wled_auto_detection_at_init(struct wled *wled)
{
int rc;
@@ -923,6 +1146,115 @@ static const struct wled_config wled4_config_defaults = {
.auto_detection_enabled = false,
};
+static int wled5_setup(struct wled *wled)
+{
+ int rc, temp, i, j;
+ u8 sink_en = 0;
+ u16 addr;
+ u32 val;
+
+ rc = regmap_update_bits(wled->regmap,
+ wled->ctrl_addr + WLED3_CTRL_REG_OVP,
+ WLED5_CTRL_REG_OVP_MASK, wled->cfg.ovp);
+ if (rc < 0)
+ return rc;
+
+ rc = regmap_update_bits(wled->regmap,
+ wled->ctrl_addr + WLED3_CTRL_REG_ILIMIT,
+ WLED3_CTRL_REG_ILIMIT_MASK,
+ wled->cfg.boost_i_limit);
+ if (rc < 0)
+ return rc;
+
+ rc = regmap_update_bits(wled->regmap,
+ wled->ctrl_addr + WLED3_CTRL_REG_FREQ,
+ WLED3_CTRL_REG_FREQ_MASK,
+ wled->cfg.switch_freq);
+ if (rc < 0)
+ return rc;
+
+ /* Per sink/string configuration */
+ for (i = 0; i < wled->cfg.num_strings; ++i) {
+ j = wled->cfg.enabled_strings[i];
+ addr = wled->sink_addr +
+ WLED4_SINK_REG_STR_FULL_SCALE_CURR(j);
+ rc = regmap_update_bits(wled->regmap, addr,
+ WLED4_SINK_REG_STR_FULL_SCALE_CURR_MASK,
+ wled->cfg.string_i_limit);
+ if (rc < 0)
+ return rc;
+
+ addr = wled->sink_addr + WLED5_SINK_REG_STR_SRC_SEL(j);
+ rc = regmap_update_bits(wled->regmap, addr,
+ WLED5_SINK_REG_SRC_SEL_MASK,
+ wled->cfg.mod_sel = MOD_A ?
+ WLED5_SINK_REG_SRC_SEL_MOD_A :
+ WLED5_SINK_REG_SRC_SEL_MOD_B);
+
+ temp = j + WLED4_SINK_REG_CURR_SINK_SHFT;
+ sink_en |= 1 << temp;
+ }
+
+ rc = wled5_cabc_config(wled, wled->cfg.cabc_sel ? true : false);
+ if (rc < 0)
+ return rc;
+
+ /* Enable one of the modulators A or B based on mod_sel */
+ addr = wled->sink_addr + WLED5_SINK_REG_MOD_A_EN;
+ val = (wled->cfg.mod_sel = MOD_A) ? WLED5_SINK_REG_MOD_EN_MASK : 0;
+ rc = regmap_update_bits(wled->regmap, addr,
+ WLED5_SINK_REG_MOD_EN_MASK, val);
+ if (rc < 0)
+ return rc;
+
+ addr = wled->sink_addr + WLED5_SINK_REG_MOD_B_EN;
+ val = (wled->cfg.mod_sel = MOD_B) ? WLED5_SINK_REG_MOD_EN_MASK : 0;
+ rc = regmap_update_bits(wled->regmap, addr,
+ WLED5_SINK_REG_MOD_EN_MASK, val);
+ if (rc < 0)
+ return rc;
+
+ addr = wled->sink_addr + wled5_brt_wid_sel_reg[wled->cfg.mod_sel];
+ val = (wled->max_brightness = WLED5_SINK_REG_BRIGHT_MAX_15B) ?
+ WLED5_SINK_REG_BRIGHTNESS_WIDTH_15B :
+ WLED5_SINK_REG_BRIGHTNESS_WIDTH_12B;
+ rc = regmap_write(wled->regmap, addr, val);
+ if (rc < 0)
+ return rc;
+
+ rc = regmap_update_bits(wled->regmap,
+ wled->sink_addr + WLED4_SINK_REG_CURR_SINK,
+ WLED4_SINK_REG_CURR_SINK_MASK, sink_en);
+ if (rc < 0)
+ return rc;
+
+ /* This updates only FSC configuration in WLED5 */
+ rc = wled->wled_sync_toggle(wled);
+ if (rc < 0) {
+ pr_err("Failed to toggle sync reg rc:%d\n", rc);
+ return rc;
+ }
+
+ rc = wled_auto_detection_at_init(wled);
+ if (rc < 0)
+ return rc;
+
+ return 0;
+}
+
+static const struct wled_config wled5_config_defaults = {
+ .boost_i_limit = 5,
+ .string_i_limit = 10,
+ .ovp = 4,
+ .num_strings = 4,
+ .switch_freq = 11,
+ .mod_sel = 0,
+ .cabc_sel = 0,
+ .cabc = false,
+ .external_pfet = false,
+ .auto_detection_enabled = false,
+};
+
static const u32 wled3_boost_i_limit_values[] = {
105, 385, 525, 805, 980, 1260, 1400, 1680,
};
@@ -941,6 +1273,16 @@ static const struct wled_var_cfg wled4_boost_i_limit_cfg = {
.size = ARRAY_SIZE(wled4_boost_i_limit_values),
};
+static inline u32 wled5_boost_i_limit_values_fn(u32 idx)
+{
+ return 525 + (idx * 175);
+}
+
+static const struct wled_var_cfg wled5_boost_i_limit_cfg = {
+ .fn = wled5_boost_i_limit_values_fn,
+ .size = 8,
+};
+
static const u32 wled3_ovp_values[] = {
35, 32, 29, 27,
};
@@ -959,6 +1301,21 @@ static const struct wled_var_cfg wled4_ovp_cfg = {
.size = ARRAY_SIZE(wled4_ovp_values),
};
+static inline u32 wled5_ovp_values_fn(u32 idx)
+{
+ /*
+ * 0000 - 38.5 V
+ * 0001 - 37 V ..
+ * 1111 - 16 V
+ */
+ return 38500 - (idx * 1500);
+}
+
+static const struct wled_var_cfg wled5_ovp_cfg = {
+ .fn = wled5_ovp_values_fn,
+ .size = 16,
+};
+
static u32 wled3_num_strings_values_fn(u32 idx)
{
return idx + 1;
@@ -1006,6 +1363,14 @@ static const struct wled_var_cfg wled4_string_cfg = {
.size = 16,
};
+static const struct wled_var_cfg wled5_mod_sel_cfg = {
+ .size = 2,
+};
+
+static const struct wled_var_cfg wled5_cabc_sel_cfg = {
+ .size = 4,
+};
+
static u32 wled_values(const struct wled_var_cfg *cfg, u32 idx)
{
if (idx >= cfg->size)
@@ -1082,6 +1447,44 @@ static int wled_configure(struct wled *wled)
},
};
+ const struct wled_u32_opts wled5_opts[] = {
+ {
+ .name = "qcom,current-boost-limit",
+ .val_ptr = &cfg->boost_i_limit,
+ .cfg = &wled5_boost_i_limit_cfg,
+ },
+ {
+ .name = "qcom,current-limit-microamp",
+ .val_ptr = &cfg->string_i_limit,
+ .cfg = &wled4_string_i_limit_cfg,
+ },
+ {
+ .name = "qcom,ovp-millivolt",
+ .val_ptr = &cfg->ovp,
+ .cfg = &wled5_ovp_cfg,
+ },
+ {
+ .name = "qcom,switching-freq",
+ .val_ptr = &cfg->switch_freq,
+ .cfg = &wled3_switch_freq_cfg,
+ },
+ {
+ .name = "qcom,num-strings",
+ .val_ptr = &cfg->num_strings,
+ .cfg = &wled4_num_strings_cfg,
+ },
+ {
+ .name = "qcom,modulator-sel",
+ .val_ptr = &cfg->mod_sel,
+ .cfg = &wled5_mod_sel_cfg,
+ },
+ {
+ .name = "qcom,cabc-sel",
+ .val_ptr = &cfg->cabc_sel,
+ .cfg = &wled5_cabc_sel_cfg,
+ },
+ };
+
const struct wled_bool_opts bool_opts[] = {
{ "qcom,cs-out", &cfg->cs_out_en, },
{ "qcom,ext-gen", &cfg->ext_gen, },
@@ -1133,6 +1536,27 @@ static int wled_configure(struct wled *wled)
wled->sink_addr = be32_to_cpu(*prop_addr);
break;
+ case 5:
+ u32_opts = wled5_opts;
+ size = ARRAY_SIZE(wled5_opts);
+ *cfg = wled5_config_defaults;
+ wled->wled_set_brightness = wled5_set_brightness;
+ wled->wled_sync_toggle = wled5_sync_toggle;
+ wled->wled_cabc_config = wled5_cabc_config;
+ wled->wled_ovp_fault_status = wled5_ovp_fault_status;
+ wled->wled_ovp_delay = wled5_ovp_delay;
+ wled->wled_auto_detection_required + wled5_auto_detection_required;
+ wled->max_string_count = 4;
+
+ prop_addr = of_get_address(dev->of_node, 1, NULL, NULL);
+ if (!prop_addr) {
+ dev_err(wled->dev, "invalid IO resources\n");
+ return -EINVAL;
+ }
+ wled->sink_addr = be32_to_cpu(*prop_addr);
+ break;
+
default:
dev_err(wled->dev, "Invalid WLED version\n");
return -EINVAL;
@@ -1286,6 +1710,10 @@ static int wled_probe(struct platform_device *pdev)
if (rc)
return rc;
+ val = WLED3_SINK_REG_BRIGHT_MAX;
+ of_property_read_u32(pdev->dev.of_node, "max-brightness", &val);
+ wled->max_brightness = val;
+
switch (wled->version) {
case 3:
wled->cfg.auto_detection_enabled = false;
@@ -1305,6 +1733,18 @@ static int wled_probe(struct platform_device *pdev)
}
break;
+ case 5:
+ wled->has_short_detect = true;
+ if (wled->cfg.cabc_sel)
+ wled->max_brightness = WLED5_SINK_REG_BRIGHT_MAX_12B;
+
+ rc = wled5_setup(wled);
+ if (rc) {
+ dev_err(&pdev->dev, "wled5_setup failed\n");
+ return rc;
+ }
+ break;
+
default:
dev_err(wled->dev, "Invalid WLED version\n");
break;
@@ -1326,7 +1766,7 @@ static int wled_probe(struct platform_device *pdev)
memset(&props, 0, sizeof(struct backlight_properties));
props.type = BACKLIGHT_RAW;
props.brightness = val;
- props.max_brightness = WLED3_SINK_REG_BRIGHT_MAX;
+ props.max_brightness = wled->max_brightness;
bl = devm_backlight_device_register(&pdev->dev, wled->name,
&pdev->dev, wled,
&wled_ops, &props);
@@ -1349,6 +1789,7 @@ static const struct of_device_id wled_match_table[] = {
{ .compatible = "qcom,pm8941-wled", .data = (void *)3 },
{ .compatible = "qcom,pmi8998-wled", .data = (void *)4 },
{ .compatible = "qcom,pm660l-wled", .data = (void *)4 },
+ { .compatible = "qcom,pm8150l-wled", .data = (void *)5 },
{}
};
MODULE_DEVICE_TABLE(of, wled_match_table);
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related [flat|nested] 4+ messages in thread