* [2.6 patch] proposed FB_MATROX_G Kconfig changes
@ 2004-12-11 16:28 Adrian Bunk
0 siblings, 0 replies; only message in thread
From: Adrian Bunk @ 2004-12-11 16:28 UTC (permalink / raw)
To: Petr Vandrovec; +Cc: adaplas, linux-fbdev-devel, linux-kernel
The current Kconfig entries for the Matrox G cards are wuite confusing:
config FB_MATROX_G450
bool "G100/G200/G400/G450/G550 support"
depends on FB_MATROX
config FB_MATROX_G100A
bool "G100/G200/G400 support"
depends on FB_MATROX && !FB_MATROX_G450
The patch below contains:
- remove FB_MATROX_G100{,A} and rename FB_MATROX_G to FB_MATROX_G450
(FB_MATROX_G450 included support from the G100 to the G550, so
I don't see any non-historic reason why to call it G450)
- small update for the FB_MATROX_G Kconfig text
The disadvantage of this patch is, that you can no longer select support
only for the G100-G400 without supporting the G450 and G550. But
compared with the current confusing Kconfig setup, I don't think that's
a big issue.
diffstat output:
drivers/video/Kconfig | 32 ++++--------------------
drivers/video/matrox/Makefile | 3 --
drivers/video/matrox/matroxfb_DAC1064.c | 25 +++++++-----------
drivers/video/matrox/matroxfb_DAC1064.h | 2 -
drivers/video/matrox/matroxfb_base.c | 6 ++--
drivers/video/matrox/matroxfb_base.h | 2 -
drivers/video/matrox/matroxfb_g450.h | 2 -
7 files changed, 23 insertions(+), 49 deletions(-)
Signed-off-by: Adrian Bunk <bunk@stusta.de>
--- linux-2.6.10-rc2-mm4-full/drivers/video/Kconfig.old 2004-12-11 17:01:17.000000000 +0100
+++ linux-2.6.10-rc2-mm4-full/drivers/video/Kconfig 2004-12-11 17:02:32.000000000 +0100
@@ -574,7 +574,7 @@
packed pixel and 32 bpp packed pixel. You can also use font widths
different from 8.
-config FB_MATROX_G450
+config FB_MATROX_G
bool "G100/G200/G400/G450/G550 support"
depends on FB_MATROX
---help---
@@ -585,10 +585,10 @@
different from 8.
If you need support for G400 secondary head, you must first say Y to
- "I2C support" and "I2C bit-banging support" in the character devices
- section, and then to "Matrox I2C support" and "G400 second head
- support" here in the framebuffer section. G450/G550 secondary head
- and digital output are supported without additional modules.
+ "I2C support" in the character devices section, and then to
+ "Matrox I2C support" and "G400 second head support" here in the
+ framebuffer section. G450/G550 secondary head and digital output
+ are supported without additional modules.
The driver starts in monitor mode. You must use the matroxset tool
(available at <ftp://platan.vc.cvut.cz/pub/linux/matrox-latest/>) to
@@ -605,26 +605,6 @@
G450/G550 hardware can display TV picture only from secondary CRTC,
and it performs no scaling, so picture must have 525 or 625 lines.
-config FB_MATROX_G100A
- bool "G100/G200/G400 support"
- depends on FB_MATROX && !FB_MATROX_G450
- ---help---
- Say Y here if you have a Matrox G100, G200 or G400 based
- video card. If you select "Advanced lowlevel driver options", you
- should check 8 bpp packed pixel, 16 bpp packed pixel, 24 bpp packed
- pixel and 32 bpp packed pixel. You can also use font widths
- different from 8.
-
- If you need support for G400 secondary head, you must first say Y to
- "I2C support" and "I2C bit-banging support" in the character devices
- section, and then to "Matrox I2C support" and "G400 second head
- support" here in the framebuffer section.
-
-config FB_MATROX_G100
- bool
- depends on FB_MATROX && (FB_MATROX_G450 || FB_MATROX_G100A)
- default y
-
config FB_MATROX_I2C
tristate "Matrox I2C support"
depends on FB_MATROX && I2C
@@ -644,7 +624,7 @@
config FB_MATROX_MAVEN
tristate "G400 second head support"
- depends on FB_MATROX_G100 && FB_MATROX_I2C
+ depends on FB_MATROX_G && FB_MATROX_I2C
---help---
WARNING !!! This support does not work with G450 !!!
--- linux-2.6.10-rc2-mm4-full/drivers/video/matrox/Makefile.old 2004-12-11 16:54:44.000000000 +0100
+++ linux-2.6.10-rc2-mm4-full/drivers/video/matrox/Makefile 2004-12-11 17:26:44.000000000 +0100
@@ -4,8 +4,7 @@
# Each configuration option enables a list of files.
-my-obj-$(CONFIG_FB_MATROX_G100) += g450_pll.o
-my-obj-$(CONFIG_FB_MATROX_G450) += matroxfb_g450.o matroxfb_crtc2.o
+my-obj-$(CONFIG_FB_MATROX_G) += g450_pll.o matroxfb_g450.o matroxfb_crtc2.o
obj-$(CONFIG_FB_MATROX) += matroxfb_base.o matroxfb_accel.o matroxfb_DAC1064.o matroxfb_Ti3026.o matroxfb_misc.o $(my-obj-y)
obj-$(CONFIG_FB_MATROX_I2C) += i2c-matroxfb.o
--- linux-2.6.10-rc2-mm4-full/drivers/video/matrox/matroxfb_base.h.old 2004-12-11 16:56:39.000000000 +0100
+++ linux-2.6.10-rc2-mm4-full/drivers/video/matrox/matroxfb_base.h 2004-12-11 16:56:50.000000000 +0100
@@ -127,7 +127,7 @@
/* G-series and Mystique have (almost) same DAC */
#undef NEED_DAC1064
-#if defined(CONFIG_FB_MATROX_MYSTIQUE) || defined(CONFIG_FB_MATROX_G100)
+#if defined(CONFIG_FB_MATROX_MYSTIQUE) || defined(CONFIG_FB_MATROX_G)
#define NEED_DAC1064 1
#endif
--- linux-2.6.10-rc2-mm4-full/drivers/video/matrox/matroxfb_base.c.old 2004-12-11 16:57:04.000000000 +0100
+++ linux-2.6.10-rc2-mm4-full/drivers/video/matrox/matroxfb_base.c 2004-12-11 17:00:23.000000000 +0100
@@ -1346,7 +1346,7 @@
#ifdef CONFIG_FB_MATROX_MYSTIQUE
static struct video_board vbMystique = {0x0800000, 0x0800000, FB_ACCEL_MATROX_MGA1064SG, &matrox_mystique};
#endif /* CONFIG_FB_MATROX_MYSTIQUE */
-#ifdef CONFIG_FB_MATROX_G100
+#ifdef CONFIG_FB_MATROX_G
static struct video_board vbG100 = {0x0800000, 0x0800000, FB_ACCEL_MATROX_MGAG100, &matrox_G100};
static struct video_board vbG200 = {0x1000000, 0x1000000, FB_ACCEL_MATROX_MGAG200, &matrox_G100};
#ifdef CONFIG_FB_MATROX_32MB
@@ -1430,7 +1430,7 @@
&vbMystique,
"Mystique 220 (PCI)"},
#endif
-#ifdef CONFIG_FB_MATROX_G100
+#ifdef CONFIG_FB_MATROX_G
{PCI_VENDOR_ID_MATROX, PCI_DEVICE_ID_MATROX_G100_MM, 0xFF,
0, 0,
DEVF_G100,
@@ -2105,7 +2105,7 @@
{PCI_VENDOR_ID_MATROX, PCI_DEVICE_ID_MATROX_MYS,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
#endif
-#ifdef CONFIG_FB_MATROX_G100
+#ifdef CONFIG_FB_MATROX_G
{PCI_VENDOR_ID_MATROX, PCI_DEVICE_ID_MATROX_G100_MM,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
{PCI_VENDOR_ID_MATROX, PCI_DEVICE_ID_MATROX_G100_AGP,
--- linux-2.6.10-rc2-mm4-full/drivers/video/matrox/matroxfb_DAC1064.h.old 2004-12-11 16:57:25.000000000 +0100
+++ linux-2.6.10-rc2-mm4-full/drivers/video/matrox/matroxfb_DAC1064.h 2004-12-11 16:58:38.000000000 +0100
@@ -9,7 +9,7 @@
#ifdef CONFIG_FB_MATROX_MYSTIQUE
extern struct matrox_switch matrox_mystique;
#endif
-#ifdef CONFIG_FB_MATROX_G100
+#ifdef CONFIG_FB_MATROX_G
extern struct matrox_switch matrox_G100;
#endif
#ifdef NEED_DAC1064
--- linux-2.6.10-rc2-mm4-full/drivers/video/matrox/matroxfb_DAC1064.c.old 2004-12-11 16:55:39.000000000 +0100
+++ linux-2.6.10-rc2-mm4-full/drivers/video/matrox/matroxfb_DAC1064.c 2004-12-11 16:59:58.000000000 +0100
@@ -155,7 +155,7 @@
hw->MXoptionReg = mx;
}
-#ifdef CONFIG_FB_MATROX_G450
+#ifdef CONFIG_FB_MATROX_G
static void g450_set_plls(WPMINFO2) {
u_int32_t c2_ctl;
unsigned int pxc;
@@ -253,7 +253,7 @@
hw->DACreg[POS1064_XMISCCTRL] &= M1064_XMISCCTRL_DAC_WIDTHMASK;
hw->DACreg[POS1064_XMISCCTRL] |= M1064_XMISCCTRL_LUT_EN;
hw->DACreg[POS1064_XPIXCLKCTRL] = M1064_XPIXCLKCTRL_PLL_UP | M1064_XPIXCLKCTRL_EN | M1064_XPIXCLKCTRL_SRC_PLL;
-#ifdef CONFIG_FB_MATROX_G450
+#ifdef CONFIG_FB_MATROX_G
if (ACCESS_FBINFO(devflags.g450dac)) {
hw->DACreg[POS1064_XPWRCTRL] = 0x1F; /* powerup everything */
hw->DACreg[POS1064_XOUTPUTCONN] = 0x00; /* disable outputs */
@@ -498,7 +498,7 @@
.compute = m1064_compute,
};
-#ifdef CONFIG_FB_MATROX_G450
+#ifdef CONFIG_FB_MATROX_G
static int g450_compute(void* out, struct my_timming* m) {
#define minfo ((struct matrox_fb_info*)out)
if (m->mnp < 0) {
@@ -541,7 +541,7 @@
}
#endif
-#ifdef CONFIG_FB_MATROX_G100
+#ifdef CONFIG_FB_MATROX_G
static int MGAG100_init(WPMINFO struct my_timming* m) {
struct matrox_hw_state* hw = &ACCESS_FBINFO(hw);
@@ -562,7 +562,7 @@
if (DAC1064_init_2(PMINFO m)) return 1;
return 0;
}
-#endif /* G100 */
+#endif /* G */
#ifdef CONFIG_FB_MATROX_MYSTIQUE
static void MGA1064_ramdac_init(WPMINFO2) {
@@ -583,7 +583,7 @@
}
#endif
-#ifdef CONFIG_FB_MATROX_G100
+#ifdef CONFIG_FB_MATROX_G
/* BIOS environ */
static int x7AF4 = 0x10; /* flags, maybe 0x10 = SDRAM, 0x00 = SGRAM??? */
/* G100 wants 0x10, G200 SGRAM does not care... */
@@ -692,8 +692,7 @@
}
#endif
-#ifdef CONFIG_FB_MATROX_G100
-#ifdef CONFIG_FB_MATROX_G450
+#ifdef CONFIG_FB_MATROX_G
static void g450_mclk_init(WPMINFO2) {
/* switch all clocks to PCI source */
pci_write_config_dword(ACCESS_FBINFO(pcidev), PCI_OPTION_REG, ACCESS_FBINFO(hw).MXoptionReg | 4);
@@ -811,10 +810,6 @@
return;
}
-#else
-static inline void g450_preinit(WPMINFO2) {
-}
-#endif
static int MGAG100_preinit(WPMINFO2) {
static const int vxres_g100[] = { 512, 640, 768, 800, 832, 960,
@@ -851,7 +846,7 @@
ACCESS_FBINFO(capable.plnwt) = ACCESS_FBINFO(devflags.accelerator) == FB_ACCEL_MATROX_MGAG100
? ACCESS_FBINFO(devflags.sgram) : 1;
-#ifdef CONFIG_FB_MATROX_G450
+#ifdef CONFIG_FB_MATROX_G
if (ACCESS_FBINFO(devflags.g450dac)) {
ACCESS_FBINFO(outputs[0]).output = &g450out;
} else
@@ -1043,7 +1038,7 @@
}
#endif
-#ifdef CONFIG_FB_MATROX_G100
+#ifdef CONFIG_FB_MATROX_G
static void MGAG100_restore(WPMINFO2) {
int i;
struct matrox_hw_state* hw = &ACCESS_FBINFO(hw);
@@ -1077,7 +1072,7 @@
EXPORT_SYMBOL(matrox_mystique);
#endif
-#ifdef CONFIG_FB_MATROX_G100
+#ifdef CONFIG_FB_MATROX_G
struct matrox_switch matrox_G100 = {
MGAG100_preinit, MGAG100_reset, MGAG100_init, MGAG100_restore,
};
--- linux-2.6.10-rc2-mm4-full/drivers/video/matrox/matroxfb_g450.h.old 2004-12-11 17:00:44.000000000 +0100
+++ linux-2.6.10-rc2-mm4-full/drivers/video/matrox/matroxfb_g450.h 2004-12-11 17:00:55.000000000 +0100
@@ -3,7 +3,7 @@
#include "matroxfb_base.h"
-#ifdef CONFIG_FB_MATROX_G450
+#ifdef CONFIG_FB_MATROX_G
void matroxfb_g450_connect(WPMINFO2);
void matroxfb_g450_shutdown(WPMINFO2);
#else
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2004-12-11 16:28 UTC | newest]
Thread overview: (only message) (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2004-12-11 16:28 [2.6 patch] proposed FB_MATROX_G Kconfig changes Adrian Bunk
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).