From: Andrew Morton <akpm@osdl.org>
To: Lobiuc Andrei <alobiuc@yahoo.com>
Cc: linux-fbdev-devel@lists.sourceforge.net
Subject: Re: PROBLEM: Radeon card displays incorrectly under the 2.6.11 version unless compiled with SMP support
Date: Mon, 21 Mar 2005 15:10:47 -0800 [thread overview]
Message-ID: <20050321151047.2650d929.akpm@osdl.org> (raw)
In-Reply-To: <20050306174932.56406.qmail@web30909.mail.mud.yahoo.com>
Lobiuc, are you able to test 2.6.12-rc1 and/or 2.6.12-rc1-mm1, see if we've
made any progress on this?
Thanks.
Lobiuc Andrei <alobiuc@yahoo.com> wrote:
>
> 1.Radeon card displays incorrectly under the 2.6.11
> version unless compiled with SMP support.
> 2.After compiling and installing the 2.6.11 kernel
> version, my ASUS Radeon 9200SE 128 MB graphic card
> does not display correctly in plain VGA mode. The same
> card has no problem with the 2.6.10 kernel.
> Regarding radeonfb, dmesg reports:
> "radeonfb_pci_register BEGIN
> ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level,
> low) -> IRQ 169
> radeonfb (0000:01:00.0): Found 131072k of DDR 64 bits
> wide videoram
> radeonfb (0000:01:00.0): mapped 16384k videoram
> radeonfb: Found Intel x86 BIOS ROM Image
> radeonfb: Retreived PLL infos from BIOS
> radeonfb: Reference=27.00 MHz (RefDiv=12)
> Memory=200.00 Mhz, System=166.00 MHz
> radeonfb: PLL min 20000 max 40000
> 1 chips in connector info
> - chip 1 has 1 connectors
> * connector 0 of type 2 (CRT) : 2300
> Starting monitor auto detection...
> radeonfb: I2C (port 1) ... not found
> radeonfb: I2C (port 2) ... not found
> radeonfb: I2C (port 3) ... found CRT display
> radeonfb: I2C (port 4) ... not found
> radeonfb: I2C (port 2) ... not found
> radeonfb: I2C (port 4) ... not found
> radeonfb: I2C (port 3) ... found CRT display
> radeonfb: Monitor 1 type CRT found
> radeonfb: EDID probed
> radeonfb: Monitor 2 type no found
> hStart = 737, hEnd = 808, hTotal = 896
> vStart = 401, vEnd = 404, vTotal = 417
> h_total_disp = 0x59006f hsync_strt_wid = 0x8802eb
> v_total_disp = 0x18f01a0 vsync_strt_wid =
> 0x830190
> pixclock = 38210
> freq = 2617
> freq = 2617, PLL min = 20000, PLL max = 40000
> ref_div = 12, ref_clk = 2700, output_freq = 20936
> ref_div = 12, ref_clk = 2700, output_freq = 20936
> post div = 0x3
> fb_div = 0x5d
> ppll_div_3 = 0x3005d
> Console: switching to colour frame buffer device 90x25
> radeonfb (0000:01:00.0): ATI Radeon Yd
> radeonfb_pci_register END
> kobject_register failed for radeonfb (-17)
> [<c01cf0c7>] kobject_register+0x57/0x60
> [<c0262707>] bus_add_driver+0x57/0xd0
> [<c0262d5f>] driver_register+0x2f/0x40
> [<c01db547>] pci_create_newid_file+0x27/0x30
> [<c01dba42>] pci_register_driver+0x62/0x80
> [<c05b3b40>] radeonfb_old_init+0x40/0x50
> [<c059c7fb>] do_initcalls+0x2b/0xc0
> [<c01002c0>] init+0x0/0x110
> [<c01002c0>] init+0x0/0x110
> [<c01002ef>] init+0x2f/0x110
> [<c010086c>] kernel_thread_helper+0x0/0x14
> [<c0100871>] kernel_thread_helper+0x5/0x14
> isapnp: Scanning for PnP cards...
> isapnp: No Plug & Play device found
> Linux agpgart interface v0.100 (c) Dave Jones
> [drm] Initialized drm 1.0.0 20040925
> ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level,
> low) -> IRQ 169
> [drm] Initialized radeon 1.14.0 20050125 on minor 0:
> ATI Technologies Inc RV280[Radeon 9200 SE]"
>
> and also
>
> "[drm:radeon_cp_init] *ERROR* radeon_cp_init called
> without lock held
> [drm:drm_unlock] *ERROR* Process 4090 using kernel
> context 0
> "
> Immediatly after the GrUB boot prompt, several lines
> of text scroll quickly down the screen, then the
> display flickers for one second and when the text
> comes back it looks huge, at a resolution that appears
> to be 320x200 (if not lower). Also, it passes the
> boundaries of the screen in all the directions.
> In console mode (Ctrl-Alt-F1) the text becomes blurred
> and with each line displayed, coloured pixels appear
> randomly on the screen.
> I tried several "vga=" modes but none seems to work.
> I uselessly recompiled several times the kernel with
> various graphic configurations.
> I made sure that support for framebuffer devices (FB),
> ATI Radeon display support (FB_RADEON and
> FB_RADEON_OLD), framebuffer console support
> (FRAMEBUFFER_CONSOLE), video mode selection support
> (VIDEO_SELECT) are all compiled as built-in.
> Drivers for no other cards were built, except for the
> first time when vga16fb and vesafb were built, making
> yet no difference.
> On the other hand, KDE looks fine at 1024x768@85Hz,
> except for the OpenGL screensavers which crawls.
>
> Accidentally, one of the compilings has been done with
> SMP support enabled on my single-processor machine and
> it turned out with this install of the kernel that the
> graphic card works ok in such conditions, displaying
> the text as it should.
>
> 3. radeonfb module; SMP
>
> 4.Linux version 2.6.11 (harken@vsoft.thenet) (gcc
> version 3.3.5 (Debian 1:3.3.5-8)) #1 SMP Sun Mar 6
> 18:27:01 EET 2005
>
> 7.
> 7.1 scripts/ver_linux
> Linux vsoft.thenet 2.6.11 #1 SMP Sun Mar 6 18:27:01
> EET 2005 i686 GNU/Linux
>
> Gnu C 3.3.5
> Gnu make 3.80
> binutils 2.15
> util-linux 2.12
> mount 2.12
> module-init-tools 3.2-pre1
> e2fsprogs 1.35
> reiserfsprogs line
> reiser4progs line
> nfs-utils 1.0.6
> Linux C Library 2.3.2
> Dynamic linker (ldd) 2.3.2
> Procps 3.2.1
> Net-tools 1.60
> Console-tools 0.2.3
> Sh-utils 5.2.1
> udev 053
> Modules Loaded via_rhine ntfs
>
> 7.2 /proc/cpuinfo
> processor : 0
> vendor_id : AuthenticAMD
> cpu family : 6
> model : 10
> model name : AMD Athlon(tm) XP 2800+
> stepping : 0
> cpu MHz : 2080.803
> cache size : 512 KB
> physical id : 0
> siblings : 1
> fdiv_bug : no
> hlt_bug : no
> f00f_bug : no
> coma_bug : no
> fpu : yes
> fpu_exception : yes
> cpuid level : 1
> wp : yes
> flags : fpu vme de pse tsc msr pae mce cx8
> apic sep mtrr pge mca cmovpat pse36 mmx fxsr sse pni
> syscall mmxext 3dnowext 3dnow
> bogomips : 4096.00
>
> 7.3 /proc/modules
> via_rhine 20868 0 - Live 0xe1979000
> ntfs 180752 1 - Live 0xe1943000
>
> 7.4 /proc/ioports
> 0000-001f : dma1
> 0020-0021 : pic1
> 0040-0043 : timer0
> 0050-0053 : timer1
> 0060-006f : keyboard
> 0080-008f : dma page reg
> 00a0-00a1 : pic2
> 00c0-00df : dma2
> 00f0-00ff : fpu
> 0170-0177 : ide1
> 01f0-01f7 : ide0
> 02f8-02ff : serial
> 0376-0376 : ide1
> 0378-037a : parport0
> 03c0-03df : vga+
> 03f6-03f6 : ide0
> 03f8-03ff : serial
> 0cf8-0cff : PCI conf1
> 4000-407f : motherboard
> 4000-4003 : PM1a_EVT_BLK
> 4004-4005 : PM1a_CNT_BLK
> 4008-400b : PM_TMR
> 4010-4015 : ACPI CPU throttle
> 4020-4023 : GPE0_BLK
> 5000-500f : motherboard
> a000-afff : PCI Bus #01
> a000-a0ff : 0000:01:00.0
> a000-a0ff : radeonfb
> c800-c80f : 0000:00:0f.0
> c800-c807 : ide0
> c808-c80f : ide1
> cc00-cc1f : 0000:00:10.0
> cc00-cc1f : uhci_hcd
> d000-d01f : 0000:00:10.1
> d000-d01f : uhci_hcd
> d400-d41f : 0000:00:10.2
> d400-d41f : uhci_hcd
> d800-d81f : 0000:00:10.3
> d800-d81f : uhci_hcd
> dc00-dcff : 0000:00:11.5
> dc00-dcff : VIA8237
> e000-e0ff : 0000:00:12.0
> e000-e0ff : via-rhine
>
> /proc/iomem
>
> 00000000-0009f7ff : System RAM
> 0009f800-0009ffff : reserved
> 000a0000-000bffff : Video RAM area
> 000c0000-000cbfff : Video ROM
> 000f0000-000fffff : System ROM
> 00100000-1ffeffff : System RAM
> 00100000-003f1a91 : Kernel code
> 003f1a92-0051503f : Kernel data
> 1fff0000-1fff2fff : ACPI Non-volatile Storage
> 1fff3000-1fffffff : ACPI Tables
> d0000000-d7ffffff : 0000:00:00.0
> d8000000-e7ffffff : PCI Bus #01
> d8000000-dfffffff : 0000:01:00.0
> d8000000-dfffffff : radeonfb
> e0000000-e7ffffff : 0000:01:00.1
> e8000000-e9ffffff : PCI Bus #01
> e9000000-e900ffff : 0000:01:00.0
> e9000000-e900ffff : radeonfb
> e9010000-e901ffff : 0000:01:00.1
> ea000000-ea0000ff : 0000:00:10.4
> ea000000-ea0000ff : ehci_hcd
> ea001000-ea0010ff : 0000:00:12.0
> ea001000-ea0010ff : via-rhine
> fec00000-fec00fff : reserved
> fee00000-fee00fff : reserved
> ffff0000-ffffffff : reserved
>
> 7.5. lspci -vvv
> 000:00:00.0 Host bridge: VIA Technologies, Inc. VT8377
> [KT400/KT600 AGP] Host Bridge (rev 80)
> Subsystem: VIA Technologies, Inc. VT8377
> [KT400/KT600 AGP] Host Bridge
> Control: I/O- Mem+ BusMaster+ SpecCycle-
> MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B- ParErr-
> DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
> Latency: 8
> Region 0: Memory at d0000000 (32-bit,
> prefetchable) [size=128M]
> Capabilities: [80] AGP version 3.5
> Status: RQ=32 Iso- ArqSz=0 Cal=2 SBA+
> ITACoh- GART64- HTrans- 64bit- FW- AGP3+ Rate=x4,x8
> Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+
> GART64- 64bit- FW- Rate=x4
> Capabilities: [c0] Power Management version 2
> Flags: PMEClk- DSI- D1- D2-
> AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0
> PME-
>
> 0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8237
> PCI Bridge (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle-
> MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B- ParErr-
> DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Bus: primary=00, secondary=01, subordinate=01,
> sec-latency=0
> I/O behind bridge: 0000a000-0000afff
> Memory behind bridge: e8000000-e9ffffff
> Prefetchable memory behind bridge:
> d8000000-e7ffffff
> BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort-
> >Reset- FastB2B-
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2-
> AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0
> PME-
>
> 0000:00:0f.0 IDE interface: VIA Technologies, Inc.
> VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master
> IDE (rev 06) (prog-if 8a [Master SecP PriP])
> Subsystem: VIA Technologies, Inc.
> VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus
> Master IDE
> Control: I/O+ Mem+ BusMaster+ SpecCycle-
> MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr-
> DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32
> Interrupt: pin A routed to IRQ 20
> Region 4: I/O ports at c800 [size=16]
> Capabilities: [c0] Power Management version 2
> Flags: PMEClk- DSI- D1- D2-
> AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0
> PME-
>
> 0000:00:10.0 USB Controller: VIA Technologies, Inc.
> VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00
> [UHCI])
> Subsystem: VIA Technologies, Inc. VT82xxxxx
> UHCI USB 1.1 Controller
> Control: I/O+ Mem+ BusMaster+ SpecCycle-
> MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr-
> DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32, Cache Line Size: 0x08 (32 bytes)
> Interrupt: pin A routed to IRQ 21
> Region 4: I/O ports at cc00 [size=32]
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+
> AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0
> PME-
>
> 0000:00:10.1 USB Controller: VIA Technologies, Inc.
> VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00
> [UHCI])
> Subsystem: VIA Technologies, Inc. VT82xxxxx
> UHCI USB 1.1 Controller
> Control: I/O+ Mem+ BusMaster+ SpecCycle-
> MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr-
> DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32, Cache Line Size: 0x08 (32 bytes)
> Interrupt: pin A routed to IRQ 21
> Region 4: I/O ports at d000 [size=32]
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+
> AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0
> PME-
>
> 0000:00:10.2 USB Controller: VIA Technologies, Inc.
> VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00
> [UHCI])
> Subsystem: VIA Technologies, Inc. VT82xxxxx
> UHCI USB 1.1 Controller
> Control: I/O+ Mem+ BusMaster+ SpecCycle-
> MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr-
> DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32, Cache Line Size: 0x08 (32 bytes)
> Interrupt: pin B routed to IRQ 21
> Region 4: I/O ports at d400 [size=32]
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+
> AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0
> PME-
>
> 0000:00:10.3 USB Controller: VIA Technologies, Inc.
> VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00
> [UHCI])
> Subsystem: VIA Technologies, Inc. VT82xxxxx
> UHCI USB 1.1 Controller
> Control: I/O+ Mem+ BusMaster+ SpecCycle-
> MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr-
> DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32, Cache Line Size: 0x08 (32 bytes)
> Interrupt: pin B routed to IRQ 21
> Region 4: I/O ports at d800 [size=32]
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+
> AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0
> PME-
>
> 0000:00:10.4 USB Controller: VIA Technologies, Inc.
> USB 2.0 (rev 86) (prog-if 20 [EHCI])
> Subsystem: VIA Technologies, Inc. USB 2.0
> Control: I/O+ Mem+ BusMaster+ SpecCycle-
> MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr-
> DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32, Cache Line Size: 0x10 (64 bytes)
> Interrupt: pin C routed to IRQ 21
> Region 0: Memory at ea000000 (32-bit,
> non-prefetchable) [size=256]
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+
> AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0
> PME-
>
> 0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8237
> ISA bridge [K8T800 South]
> Subsystem: VIA Technologies, Inc. VT8237 ISA
> bridge [K8T800 South]
> Control: I/O+ Mem+ BusMaster+ SpecCycle-
> MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr-
> DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Capabilities: [c0] Power Management version 2
> Flags: PMEClk- DSI- D1- D2-
> AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0
> PME-
>
> 0000:00:11.5 Multimedia audio controller: VIA
> Technologies, Inc. VT8233/A/8235/8237 AC97 Audio
> Controller (rev 60)
> Subsystem: Unknown device 1695:300c
> Control: I/O+ Mem- BusMaster- SpecCycle-
> MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr-
> DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Interrupt: pin C routed to IRQ 22
> Region 0: I/O ports at dc00 [size=256]
> Capabilities: [c0] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+
> AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0
> PME-
>
> 0000:00:12.0 Ethernet controller: VIA Technologies,
> Inc. VT6102 [Rhine-II] (rev78)
> Subsystem: VIA Technologies, Inc. VT6102
> [Rhine II] Embeded Ethernet Controller on VT8235
> Control: I/O+ Mem+ BusMaster+ SpecCycle-
> MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr-
> DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (750ns min, 2000ns max), Cache
> Line Size: 0x08 (32 bytes)
> Interrupt: pin A routed to IRQ 23
> Region 0: I/O ports at e000 [size=256]
> Region 1: Memory at ea001000 (32-bit,
> non-prefetchable) [size=256]
> Capabilities: [40] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+
> AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0
> PME-
>
> 0000:01:00.0 VGA compatible controller: ATI
> Technologies Inc RV280 [Radeon 9200SE] (rev 01)
> (prog-if 00 [VGA])
> Subsystem: Asustek Computer, Inc.: Unknown
> device c008
> Control: I/O+ Mem+ BusMaster+ SpecCycle-
> MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr-
> DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (2000ns min), Cache Line Size:
> 0x08 (32 bytes)
> Interrupt: pin A routed to IRQ 16
> Region 0: Memory at d8000000 (32-bit,
> prefetchable) [size=128M]
> Region 1: I/O ports at a000 [size=256]
> Region 2: Memory at e9000000 (32-bit,
> non-prefetchable) [size=64K]
> Capabilities: [58] AGP version 3.0
> Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+
> ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
> Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+
> GART64- 64bit- FW- Rate=x4
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+
> AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0
> PME-
>
> 0000:01:00.1 Display controller: ATI Technologies Inc
> RV280 [Radeon 9200 SE] (Secondary) (rev 01)
> Subsystem: Asustek Computer, Inc.: Unknown
> device c009
> Control: I/O- Mem- BusMaster+ SpecCycle-
> MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr-
> DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (2000ns min), Cache Line Size:
> 0x08 (32 bytes)
> Region 0: Memory at e0000000 (32-bit,
> prefetchable) [disabled] [size=128M]
> Region 1: Memory at e9010000 (32-bit,
> non-prefetchable) [disabled] [size=64K]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+
> AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0
> PME-
>
> Thank you very much for your time!
> Regards, Andrei Lobiuc
>
>
>
>
> __________________________________
> Celebrate Yahoo!'s 10th Birthday!
> Yahoo! Netrospective: 100 Moments of the Web
> http://birthday.yahoo.com/netrospective/
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
-------------------------------------------------------
SF email is sponsored by - The IT Product Guide
Read honest & candid reviews on hundreds of IT Products from real users.
Discover which products truly live up to the hype. Start reading now.
http://ads.osdn.com/?ad_id=6595&alloc_id=14396&op=click
next parent reply other threads:[~2005-03-21 23:11 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <20050306174932.56406.qmail@web30909.mail.mud.yahoo.com>
2005-03-21 23:10 ` Andrew Morton [this message]
2005-03-22 12:32 PROBLEM: Radeon card displays incorrectly under the 2.6.11 version unless compiled with SMP support Lobiuc Andrei
-- strict thread matches above, loose matches on Subject: below --
2005-03-22 12:43 Lobiuc Andrei
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20050321151047.2650d929.akpm@osdl.org \
--to=akpm@osdl.org \
--cc=alobiuc@yahoo.com \
--cc=linux-fbdev-devel@lists.sourceforge.net \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).