From: Stuffed Crust <pizza@shaftnet.org>
To: linux-fbdev-devel@lists.sourceforge.net
Subject: [patch] [radeonfb] Radeon Mobility X700 (M26) and ATOM bios support
Date: Tue, 3 Jan 2006 15:44:04 -0500 [thread overview]
Message-ID: <20060103204404.GA23313@shaftnet.org> (raw)
[-- Attachment #1.1: Type: text/plain, Size: 3128 bytes --]
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Newer Radeon graphics cards use a different table layout in their
BIOSes, known as 'ATOM'.
I've attached a patch (against 2.6.15) which implements the PLL and LVDS
parsing out of the ATOM BIOSes, using the current X.org sources as a
reference. Notably absent is the code which detects the connectors and
TDMS information, but it's of lesser importance at the moment.
This code still has quirks, but I'm not sure if those are due to bugs in
my patch or incomplete/buggy support for the RV410. So I'd appreciate
it if people could try this out, especially if they have a newer ATOM
BIOS in their radeon card, and let me know what happens.
Finally, this patch also has PCI IDs added for my Radeon Mobility X700
(M26) adapter.
Below is the dump of my system with this driver:
radeonfb_pci_register BEGIN
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 18 (level, low) -> IRQ 217
radeonfb (0000:01:00.0): Found 131072k of DDR 128 bits wide videoram
radeonfb (0000:01:00.0): mapped 16384k videoram
ATOM BIOS detected
radeonfb: Retreived PLL infos from BIOS
radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=330.00 Mhz, System=358.00 MHz
radeonfb: PLL min 20000 max 50000
XXXX Write ATOM BIOS connector parse
Starting monitor auto detection...
radeonfb: I2C (port 1) ... not found
radeonfb: I2C (port 2) ... not found
radeonfb: I2C (port 3) ... not found
radeonfb: I2C (port 4) ... not found
radeonfb: I2C (port 2) ... not found
radeonfb: I2C (port 4) ... not found
Non-DDC laptop panel detected
radeonfb: I2C (port 3) ... not found
radeonfb: I2C (port 4) ... not found
radeonfb: Monitor 1 type LCD found
radeonfb: Monitor 2 type CRT found
radeonfb: detected LVDS panel size from BIOS: 1680x1050
BIOS provided panel power delay: 15369
Setting up default mode based on panel info
radeonfb: Dynamic Clock Power Management enabled
hStart = 1728, hEnd = 1760, hTotal = 1840
vStart = 1053, vEnd = 1059, vTotal = 1080
h_total_disp = 0xd100e5 hsync_strt_wid = 0x406ba
v_total_disp = 0x4190437 vsync_strt_wid = 0x6041c
pixclock = 8387
freq = 11923
freq = 11923, PLL min = 20000, PLL max = 50000
ref_div = 12, ref_clk = 2700, output_freq = 23846
ref_div = 12, ref_clk = 2700, output_freq = 23846
post div = 0x1
fb_div = 0x6a
ppll_div_3 = 0x1006a
Console: switching to colour frame buffer device 210x65
radeonfb (0000:01:00.0): ATI Radeon VS
radeonfb_pci_register END
And at this point, I have yummy hires fbdev goodness.
I also have a question about the panel_info.pwr_delay field --- Is this
is supposed to be the time we wait for the LCD to settle after a power
state change? X.org seems to use 200ms everywhere, but the default in
radeonfb seems to be 2000ms, and my panel is reporting a whopping
15369ms. I'm also forced to use the default pll.ref_div of 12, and I've
tweaked the code to make that default universal if the BIOS information
is clearly bogus.
- Solomon
--
Solomon Peachy ICQ: 1318344
Melbourne, FL
Quidquid latine dictum sit, altum viditur.
[-- Attachment #1.2: radeon_atom_bios.diff --]
[-- Type: text/plain, Size: 15832 bytes --]
diff -ur /tmp/linux-2.6.15/drivers/video/aty/ati_ids.h ./aty/ati_ids.h
--- /tmp/linux-2.6.15/drivers/video/aty/ati_ids.h 2006-01-03 14:30:15.000000000 -0500
+++ ./aty/ati_ids.h 2006-01-03 15:12:01.000000000 -0500
@@ -185,6 +185,8 @@
#define PCI_CHIP_R423_UQ 0x5551
#define PCI_CHIP_R423_UR 0x5552
#define PCI_CHIP_R423_UT 0x5554
+#define PCI_CHIP_RV410_5652 0x5652
+#define PCI_CHIP_RV410_VS 0x5653
#define PCI_CHIP_MACH64VT 0x5654
#define PCI_CHIP_MACH64VU 0x5655
#define PCI_CHIP_MACH64VV 0x5656
diff -ur /tmp/linux-2.6.15/drivers/video/aty/radeon_base.c ./aty/radeon_base.c
--- /tmp/linux-2.6.15/drivers/video/aty/radeon_base.c 2006-01-03 14:30:15.000000000 -0500
+++ ./aty/radeon_base.c 2006-01-03 15:13:48.000000000 -0500
@@ -214,6 +214,8 @@
CHIP_DEF(PCI_CHIP_R420_JL, R420, CHIP_HAS_CRTC2),
CHIP_DEF(PCI_CHIP_R420_JM, R420, CHIP_HAS_CRTC2),
CHIP_DEF(PCI_CHIP_R420_JN, R420, CHIP_HAS_CRTC2 | CHIP_IS_MOBILITY),
+ CHIP_DEF(PCI_CHIP_RV410_5652, R420, CHIP_HAS_CRTC2 | CHIP_IS_MOBILITY),
+ CHIP_DEF(PCI_CHIP_RV410_VS, R420, CHIP_HAS_CRTC2 | CHIP_IS_MOBILITY),
CHIP_DEF(PCI_CHIP_R420_JP, R420, CHIP_HAS_CRTC2),
CHIP_DEF(PCI_CHIP_R423_UH, R420, CHIP_HAS_CRTC2),
CHIP_DEF(PCI_CHIP_R423_UI, R420, CHIP_HAS_CRTC2),
@@ -342,7 +344,7 @@
* to phase out Open Firmware images.
*
* Currently, we only look at the first PCI data, we could iteratre and deal with
- * them all, and we should use fb_bios_start relative to start of image and not
+ * them all, and we should use fp_bios_start relative to start of image and not
* relative start of ROM, but so far, I never found a dual-image ATI card
*
* typedef struct {
@@ -655,8 +657,6 @@
rinfo->pll.ref_clk = 2700;
break;
}
- rinfo->pll.ref_div = INPLL(PPLL_REF_DIV) & PPLL_REF_DIV_MASK;
-
#ifdef CONFIG_PPC_OF
/*
@@ -673,14 +673,31 @@
* and if yes, retreive them
*/
if (!force_measure_pll && rinfo->bios_seg) {
- u16 pll_info_block = BIOS_IN16(rinfo->fp_bios_start + 0x30);
+ u16 pll_info_block;
+ if (rinfo->is_atom_bios) {
+ pll_info_block = BIOS_IN16(rinfo->atom_data_start + 12);
+
+ rinfo->pll.sclk = BIOS_IN32(pll_info_block + 8);
+ rinfo->pll.mclk = BIOS_IN32(pll_info_block + 12);
+ rinfo->pll.ref_clk = BIOS_IN16(pll_info_block + 82);
+ rinfo->pll.ref_div = 0; /* Have to get it elsewhere */
+ rinfo->pll.ppll_min = BIOS_IN16(pll_info_block + 78);
+ rinfo->pll.ppll_max = BIOS_IN32(pll_info_block + 32);
+
+ if (rinfo->pll.sclk == 0) rinfo->pll.sclk = 20000;
+ if (rinfo->pll.mclk == 0) rinfo->pll.mclk = 20000;
- rinfo->pll.sclk = BIOS_IN16(pll_info_block + 0x08);
- rinfo->pll.mclk = BIOS_IN16(pll_info_block + 0x0a);
- rinfo->pll.ref_clk = BIOS_IN16(pll_info_block + 0x0e);
- rinfo->pll.ref_div = BIOS_IN16(pll_info_block + 0x10);
- rinfo->pll.ppll_min = BIOS_IN32(pll_info_block + 0x12);
- rinfo->pll.ppll_max = BIOS_IN32(pll_info_block + 0x16);
+ } else {
+ pll_info_block = BIOS_IN16(rinfo->fp_bios_start + 0x30);
+
+ rinfo->pll.sclk = BIOS_IN16(pll_info_block + 0x08);
+ rinfo->pll.mclk = BIOS_IN16(pll_info_block + 0x0a);
+ rinfo->pll.ref_clk = BIOS_IN16(pll_info_block + 0x0e);
+ rinfo->pll.ref_div = BIOS_IN16(pll_info_block + 0x10);
+ rinfo->pll.ppll_min = BIOS_IN32(pll_info_block + 0x12);
+ rinfo->pll.ppll_max = BIOS_IN32(pll_info_block + 0x16);
+
+ }
printk(KERN_INFO "radeonfb: Retreived PLL infos from BIOS\n");
goto found;
@@ -701,6 +718,22 @@
printk(KERN_INFO "radeonfb: Used default PLL infos\n");
found:
+
+ /* Check and fix-up the PLL divisor if necessary */
+ if (rinfo->pll.ref_div < 2) {
+ int tmp = INPLL(PPLL_REF_DIV);
+ if (rinfo->family == CHIP_FAMILY_RS300) {
+ rinfo->pll.ref_div = (tmp & R300_PPLL_REF_DIV_ACC_MASK) >> R300_PPLL_REF_DIV_ACC_SHIFT;
+ } else {
+ rinfo->pll.ref_div = tmp & PPLL_REF_DIV_MASK;
+ }
+
+ /* Sane default */
+ if (rinfo->pll.ref_div < 2) {
+ rinfo->pll.ref_div = 12;
+ }
+ }
+
/*
* Some methods fail to retreive SCLK and MCLK values, we apply default
* settings in this case (200Mhz). If that really happne often, we could
@@ -2412,6 +2445,7 @@
* We probably need to make sure this is the primary display,
* but that is difficult without some arch support.
*/
+
#ifdef CONFIG_X86
if (rinfo->bios_seg == NULL)
radeon_find_mem_vbios(rinfo);
@@ -2423,6 +2457,28 @@
if (rinfo->bios_seg == NULL && rinfo->is_mobility)
radeon_map_ROM(rinfo, pdev);
+ /* Check BIOS Type */
+ {
+ int tmp = rinfo->fp_bios_start + 4;
+ if ((BIOS_IN8(tmp) == 'A' &&
+ BIOS_IN8(tmp+1) == 'T' &&
+ BIOS_IN8(tmp+2) == 'O' &&
+ BIOS_IN8(tmp+3) == 'M') ||
+ (BIOS_IN8(tmp) == 'M' &&
+ BIOS_IN8(tmp+1) == 'O' &&
+ BIOS_IN8(tmp+2) == 'T' &&
+ BIOS_IN8(tmp+3) == 'A')) {
+ rinfo->is_atom_bios = 1;
+ } else {
+ rinfo->is_atom_bios = 0;
+ }
+ }
+
+ if (rinfo->is_atom_bios) {
+ rinfo->atom_data_start = BIOS_IN16(rinfo->fp_bios_start + 32);
+ printk("ATOM BIOS detected\n");
+ }
+
/* Get informations about the board's PLL */
radeon_get_pllinfo(rinfo);
diff -ur /tmp/linux-2.6.15/drivers/video/aty/radeon_monitor.c ./aty/radeon_monitor.c
--- /tmp/linux-2.6.15/drivers/video/aty/radeon_monitor.c 2005-10-27 20:02:08.000000000 -0400
+++ ./aty/radeon_monitor.c 2006-01-03 12:15:55.000000000 -0500
@@ -169,76 +169,117 @@
if (!rinfo->bios_seg)
return 0;
- if (!(tmp = BIOS_IN16(rinfo->fp_bios_start + 0x40))) {
- printk(KERN_ERR "radeonfb: Failed to detect DFP panel info using BIOS\n");
- rinfo->panel_info.pwr_delay = 200;
- return 0;
- }
- for(i=0; i<24; i++)
- stmp[i] = BIOS_IN8(tmp+i+1);
- stmp[24] = 0;
- printk("radeonfb: panel ID string: %s\n", stmp);
- rinfo->panel_info.xres = BIOS_IN16(tmp + 25);
- rinfo->panel_info.yres = BIOS_IN16(tmp + 27);
- printk("radeonfb: detected LVDS panel size from BIOS: %dx%d\n",
- rinfo->panel_info.xres, rinfo->panel_info.yres);
-
- rinfo->panel_info.pwr_delay = BIOS_IN16(tmp + 44);
- RTRACE("BIOS provided panel power delay: %d\n", rinfo->panel_info.pwr_delay);
- if (rinfo->panel_info.pwr_delay > 2000 || rinfo->panel_info.pwr_delay <= 0)
- rinfo->panel_info.pwr_delay = 2000;
+ if (rinfo->is_atom_bios) {
+ tmp = BIOS_IN16(rinfo->atom_data_start + 16);
+ if (!tmp) {
+ printk(KERN_ERR "radeonfb: Failed to detect DFP panel info using BIOS\n");
+ rinfo->panel_info.pwr_delay = 200;
+ return 0;
+ }
- /*
- * Some panels only work properly with some divider combinations
- */
- rinfo->panel_info.ref_divider = BIOS_IN16(tmp + 46);
- rinfo->panel_info.post_divider = BIOS_IN8(tmp + 48);
- rinfo->panel_info.fbk_divider = BIOS_IN16(tmp + 49);
- if (rinfo->panel_info.ref_divider != 0 &&
- rinfo->panel_info.fbk_divider > 3) {
- rinfo->panel_info.use_bios_dividers = 1;
- printk(KERN_INFO "radeondb: BIOS provided dividers will be used\n");
- RTRACE("ref_divider = %x\n", rinfo->panel_info.ref_divider);
- RTRACE("post_divider = %x\n", rinfo->panel_info.post_divider);
- RTRACE("fbk_divider = %x\n", rinfo->panel_info.fbk_divider);
- }
- RTRACE("Scanning BIOS table ...\n");
- for(i=0; i<32; i++) {
- tmp0 = BIOS_IN16(tmp+64+i*2);
- if (tmp0 == 0)
- break;
- RTRACE(" %d x %d\n", BIOS_IN16(tmp0), BIOS_IN16(tmp0+2));
- if ((BIOS_IN16(tmp0) == rinfo->panel_info.xres) &&
- (BIOS_IN16(tmp0+2) == rinfo->panel_info.yres)) {
- rinfo->panel_info.hblank = (BIOS_IN16(tmp0+17) - BIOS_IN16(tmp0+19)) * 8;
- rinfo->panel_info.hOver_plus = ((BIOS_IN16(tmp0+21) -
- BIOS_IN16(tmp0+19) -1) * 8) & 0x7fff;
- rinfo->panel_info.hSync_width = BIOS_IN8(tmp0+23) * 8;
- rinfo->panel_info.vblank = BIOS_IN16(tmp0+24) - BIOS_IN16(tmp0+26);
- rinfo->panel_info.vOver_plus = (BIOS_IN16(tmp0+28) & 0x7ff) - BIOS_IN16(tmp0+26);
- rinfo->panel_info.vSync_width = (BIOS_IN16(tmp0+28) & 0xf800) >> 11;
- rinfo->panel_info.clock = BIOS_IN16(tmp0+9);
- /* Assume high active syncs for now until ATI tells me more... maybe we
- * can probe register values here ?
- */
- rinfo->panel_info.hAct_high = 1;
- rinfo->panel_info.vAct_high = 1;
- /* Mark panel infos valid */
- rinfo->panel_info.valid = 1;
-
- RTRACE("Found panel in BIOS table:\n");
- RTRACE(" hblank: %d\n", rinfo->panel_info.hblank);
- RTRACE(" hOver_plus: %d\n", rinfo->panel_info.hOver_plus);
- RTRACE(" hSync_width: %d\n", rinfo->panel_info.hSync_width);
- RTRACE(" vblank: %d\n", rinfo->panel_info.vblank);
- RTRACE(" vOver_plus: %d\n", rinfo->panel_info.vOver_plus);
- RTRACE(" vSync_width: %d\n", rinfo->panel_info.vSync_width);
- RTRACE(" clock: %d\n", rinfo->panel_info.clock);
+ rinfo->panel_info.xres = BIOS_IN16(tmp+6);
+ rinfo->panel_info.yres = BIOS_IN16(tmp+10);
+ printk("radeonfb: detected LVDS panel size from BIOS: %dx%d\n",
+ rinfo->panel_info.xres, rinfo->panel_info.yres);
+ rinfo->panel_info.pwr_delay = BIOS_IN16(tmp+40);
+ RTRACE("BIOS provided panel power delay: %d\n", rinfo->panel_info.pwr_delay);
+ if (rinfo->panel_info.pwr_delay > 2000 || rinfo->panel_info.pwr_delay <= 0)
+ rinfo->panel_info.pwr_delay = 2000;
+
+ /* No special divider combinations? */
+
+ rinfo->panel_info.hblank = BIOS_IN16(tmp+8);
+ rinfo->panel_info.hOver_plus = BIOS_IN16(tmp+14);
+ rinfo->panel_info.hSync_width = BIOS_IN16(tmp+16);
+ rinfo->panel_info.vblank = BIOS_IN16(tmp+12);
+ rinfo->panel_info.vOver_plus = BIOS_IN16(tmp+18);
+ rinfo->panel_info.vSync_width = BIOS_IN16(tmp+20);
+ rinfo->panel_info.clock = BIOS_IN16(tmp+4);
+
+ /* Assume high active syncs for now until ATI tells me more... maybe we
+ * can probe register values here ?
+ */
+ rinfo->panel_info.hAct_high = 1;
+ rinfo->panel_info.vAct_high = 1;
+ /* Mark panel infos valid */
+ rinfo->panel_info.valid = 1;
+
+ return 1;
+ } else {
+ if (!(tmp = BIOS_IN16(rinfo->fp_bios_start + 0x40))) {
+ printk(KERN_ERR "radeonfb: Failed to detect DFP panel info using BIOS\n");
+ rinfo->panel_info.pwr_delay = 200;
+ return 0;
+ }
+
+ for(i=0; i<24; i++)
+ stmp[i] = BIOS_IN8(tmp+i+1);
+ stmp[24] = 0;
+ printk("radeonfb: panel ID string: %s\n", stmp);
+ rinfo->panel_info.xres = BIOS_IN16(tmp + 25);
+ rinfo->panel_info.yres = BIOS_IN16(tmp + 27);
+ printk("radeonfb: detected LVDS panel size from BIOS: %dx%d\n",
+ rinfo->panel_info.xres, rinfo->panel_info.yres);
+
+ rinfo->panel_info.pwr_delay = BIOS_IN16(tmp + 44);
+ RTRACE("BIOS provided panel power delay: %d\n", rinfo->panel_info.pwr_delay);
+ if (rinfo->panel_info.pwr_delay > 2000 || rinfo->panel_info.pwr_delay <= 0)
+ rinfo->panel_info.pwr_delay = 2000;
+
+ /*
+ * Some panels only work properly with some divider combinations
+ */
+ rinfo->panel_info.ref_divider = BIOS_IN16(tmp + 46);
+ rinfo->panel_info.post_divider = BIOS_IN8(tmp + 48);
+ rinfo->panel_info.fbk_divider = BIOS_IN16(tmp + 49);
+ if (rinfo->panel_info.ref_divider != 0 &&
+ rinfo->panel_info.fbk_divider > 3) {
+ rinfo->panel_info.use_bios_dividers = 1;
+ printk(KERN_INFO "radeondb: BIOS provided dividers will be used\n");
+ RTRACE("ref_divider = %x\n", rinfo->panel_info.ref_divider);
+ RTRACE("post_divider = %x\n", rinfo->panel_info.post_divider);
+ RTRACE("fbk_divider = %x\n", rinfo->panel_info.fbk_divider);
+ }
+
+ RTRACE("Scanning BIOS table ...\n");
+ for(i=0; i<32; i++) {
+ tmp0 = BIOS_IN16(tmp+64+i*2);
+ if (tmp0 == 0)
+ break;
+ RTRACE(" %d x %d\n", BIOS_IN16(tmp0), BIOS_IN16(tmp0+2));
+ if ((BIOS_IN16(tmp0) == rinfo->panel_info.xres) &&
+ (BIOS_IN16(tmp0+2) == rinfo->panel_info.yres)) {
+ rinfo->panel_info.hblank = (BIOS_IN16(tmp0+17) - BIOS_IN16(tmp0+19)) * 8;
+ rinfo->panel_info.hOver_plus = ((BIOS_IN16(tmp0+21) -
+ BIOS_IN16(tmp0+19) -1) * 8) & 0x7fff;
+ rinfo->panel_info.hSync_width = BIOS_IN8(tmp0+23) * 8;
+ rinfo->panel_info.vblank = BIOS_IN16(tmp0+24) - BIOS_IN16(tmp0+26);
+ rinfo->panel_info.vOver_plus = (BIOS_IN16(tmp0+28) & 0x7ff) - BIOS_IN16(tmp0+26);
+ rinfo->panel_info.vSync_width = (BIOS_IN16(tmp0+28) & 0xf800) >> 11;
+ rinfo->panel_info.clock = BIOS_IN16(tmp0+9);
+ /* Assume high active syncs for now until ATI tells me more... maybe we
+ * can probe register values here ?
+ */
+ rinfo->panel_info.hAct_high = 1;
+ rinfo->panel_info.vAct_high = 1;
+ /* Mark panel infos valid */
+ rinfo->panel_info.valid = 1;
- return 1;
+ RTRACE("Found panel in BIOS table:\n");
+ RTRACE(" hblank: %d\n", rinfo->panel_info.hblank);
+ RTRACE(" hOver_plus: %d\n", rinfo->panel_info.hOver_plus);
+ RTRACE(" hSync_width: %d\n", rinfo->panel_info.hSync_width);
+ RTRACE(" vblank: %d\n", rinfo->panel_info.vblank);
+ RTRACE(" vOver_plus: %d\n", rinfo->panel_info.vOver_plus);
+ RTRACE(" vSync_width: %d\n", rinfo->panel_info.vSync_width);
+ RTRACE(" clock: %d\n", rinfo->panel_info.clock);
+
+ return 1;
+ }
}
}
+
RTRACE("Didn't find panel in BIOS table !\n");
return 0;
@@ -261,29 +302,34 @@
if (!rinfo->bios_seg)
return;
- offset = BIOS_IN16(rinfo->fp_bios_start + 0x50);
- if (offset == 0) {
- printk(KERN_WARNING "radeonfb: No connector info table detected\n");
- return;
- }
-
- /* Don't do much more at this point but displaying the data if
- * DEBUG is enabled
- */
- chips = BIOS_IN8(offset++) >> 4;
- RTRACE("%d chips in connector info\n", chips);
- for (i = 0; i < chips; i++) {
- tmp = BIOS_IN8(offset++);
- connectors = tmp & 0x0f;
- RTRACE(" - chip %d has %d connectors\n", tmp >> 4, connectors);
- for (conn = 0; ; conn++) {
- tmp = BIOS_IN16(offset);
- if (tmp == 0)
- break;
- offset += 2;
- type = (tmp >> 12) & 0x0f;
- RTRACE(" * connector %d of type %d (%s) : %04x\n",
- conn, type, __conn_type_table[type], tmp);
+ if (rinfo->is_atom_bios) {
+ printk(KERN_WARNING "XXXX Write ATOM BIOS connector parse\n");
+ } else {
+
+ offset = BIOS_IN16(rinfo->fp_bios_start + 0x50);
+ if (offset == 0) {
+ printk(KERN_WARNING "radeonfb: No connector info table detected\n");
+ return;
+ }
+
+ /* Don't do much more at this point but displaying the data if
+ * DEBUG is enabled
+ */
+ chips = BIOS_IN8(offset++) >> 4;
+ RTRACE("%d chips in connector info\n", chips);
+ for (i = 0; i < chips; i++) {
+ tmp = BIOS_IN8(offset++);
+ connectors = tmp & 0x0f;
+ RTRACE(" - chip %d has %d connectors\n", tmp >> 4, connectors);
+ for (conn = 0; ; conn++) {
+ tmp = BIOS_IN16(offset);
+ if (tmp == 0)
+ break;
+ offset += 2;
+ type = (tmp >> 12) & 0x0f;
+ RTRACE(" * connector %d of type %d (%s) : %04x\n",
+ conn, type, __conn_type_table[type], tmp);
+ }
}
}
}
@@ -519,6 +565,8 @@
/*
* Check for cards with reversed DACs or TMDS controllers using BIOS
*/
+ // XXXX What about atom_bios types?
+
if (rinfo->bios_seg &&
(tmp = BIOS_IN16(rinfo->fp_bios_start + 0x50))) {
for (i = 1; i < 4; i++) {
diff -ur /tmp/linux-2.6.15/drivers/video/aty/radeonfb.h ./aty/radeonfb.h
--- /tmp/linux-2.6.15/drivers/video/aty/radeonfb.h 2006-01-03 14:30:15.000000000 -0500
+++ ./aty/radeonfb.h 2006-01-03 11:30:51.000000000 -0500
@@ -298,6 +298,9 @@
void __iomem *bios_seg;
int fp_bios_start;
+ int is_atom_bios;
+ int atom_data_start;
+
u32 pseudo_palette[17];
struct { u8 red, green, blue, pad; }
palette[256];
[-- Attachment #2: Type: application/pgp-signature, Size: 189 bytes --]
next reply other threads:[~2006-01-03 20:48 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-01-03 20:44 Stuffed Crust [this message]
2006-01-03 23:29 ` [patch] [radeonfb] Radeon Mobility X700 (M26) and ATOM bios support Petr Vandrovec
2006-01-05 9:59 ` Benjamin Herrenschmidt
2006-01-05 20:13 ` Stuffed Crust
2006-02-14 21:28 ` Benjamin Herrenschmidt
2006-02-22 22:19 ` Stuffed Crust
2006-02-23 6:09 ` Stuffed Crust
2006-02-23 6:50 ` Benjamin Herrenschmidt
2006-02-23 22:36 ` [patch] [radeonfb] Radeon M26 and ATOM bios support (take 4) Stuffed Crust
2006-02-23 23:15 ` Benjamin Herrenschmidt
2006-03-01 3:33 ` Stuffed Crust
2006-03-01 3:46 ` Benjamin Herrenschmidt
2006-03-01 16:56 ` Gabor Gombas
2006-03-01 20:36 ` Stuffed Crust
2006-03-01 21:34 ` [patch] [radeonfb] Radeon M26 and ATOM bios support (take 5) Stuffed Crust
2006-03-01 21:47 ` Benjamin Herrenschmidt
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20060103204404.GA23313@shaftnet.org \
--to=pizza@shaftnet.org \
--cc=linux-fbdev-devel@lists.sourceforge.net \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).