* [PATCH] ARM: OMAP: Remove broken LCD driver for SX1 (Re: Please fix lcd_sx1.c)
[not found] ` <20081124212003.GC11997@atomide.com>
@ 2008-11-25 2:22 ` Tony Lindgren
0 siblings, 0 replies; only message in thread
From: Tony Lindgren @ 2008-11-25 2:22 UTC (permalink / raw)
To: Russell King - ARM Linux
Cc: linux-omap, linux-arm-kernel, linux-fbdev-devel, Vovan888
[-- Attachment #1: Type: text/plain, Size: 1526 bytes --]
* Tony Lindgren <tony@atomide.com> [081124 13:21]:
> * Russell King - ARM Linux <linux@arm.linux.org.uk> [081123 08:58]:
> > On Sun, Nov 23, 2008 at 04:46:18PM +0000, Russell King - ARM Linux wrote:
> > > To me, it looks like this driver was tossed over into mainline without
> > > any thought - it has never been in a buildable state. Please fix or
> > > remove this driver from mainline.
> >
> > Actually, it was buildable, until this commit:
> >
> > commit b4b58f5834a023dab67201db9a626bef07bb200c
> > Author: Chandra Shekhar <x0044955@ti.com>
> > Date: Wed Oct 8 10:01:39 2008 +0300
> >
> > ARM: OMAP: Allocate McBSP devices dynamically
> >
> > Based on Chandra's earlier patches in linux-omap tree.
> >
> > Note that omap1_mcbsp_check and omap2_mcbsp_check are no longer
> > needed as there's now omap_mcbsp_check_valid_id() defined.
> >
> > Also some functions can now be marked __init.
> >
> > Signed-off-by: Chandra Shekhar <x0044955@ti.com>
> > Signed-off-by: Tony Lindgren <tony@atomide.com>
> >
> > which means it's a regression and therefore needs fixing before 2.6.28.
>
> Will send you a patch for this today.
Well looks like there's no way I can fix this. I don't have the
hardware, so people using sx1 would need to fix this.
Looks like the driver is attempting to use SPI mode, but is doing it
in a different way compared to mcbsp.c.
I'm suggesting the following patch unless somebody can do a real patch
for this over next few days.
Regards,
Tony
[-- Attachment #2: lcd-sx1-remove.patch --]
[-- Type: text/x-diff, Size: 9722 bytes --]
From 7953031da4200323ab5d85bd514054ca4ba9d225 Mon Sep 17 00:00:00 2001
From: Tony Lindgren <tony@atomide.com>
Date: Mon, 24 Nov 2008 18:11:16 -0800
Subject: [PATCH] ARM: OMAP: Remove broken LCD driver for SX1
Recently the omap McBSP code was cleaned up to get rid of
direct McBSP register tinkering by the drivers. Looks like
lcd_sx1.c never got converted, and now it breaks builds.
It seems the lcd_sx1.c driver is attempting SPI mode, but
doing it in a different way compared to omap_mcbsp_set_spi_mode().
Remove the broken driver, patches welcome to add it back when
done properly by patching both mcbsp.c and lcd_sx1.c.
Cc: Vovan888@gmail.com
Cc: linux-fbdev-devel@lists.sourceforge.net
Signed-off-by: Tony Lindgren <tony@atomide.com>
diff --git a/drivers/video/omap/Makefile b/drivers/video/omap/Makefile
index 99da8b6..ed13889 100644
--- a/drivers/video/omap/Makefile
+++ b/drivers/video/omap/Makefile
@@ -23,7 +23,6 @@ objs-y$(CONFIG_MACH_OMAP_PALMZ71) += lcd_palmz71.o
objs-$(CONFIG_ARCH_OMAP16XX)$(CONFIG_MACH_OMAP_INNOVATOR) += lcd_inn1610.o
objs-$(CONFIG_ARCH_OMAP15XX)$(CONFIG_MACH_OMAP_INNOVATOR) += lcd_inn1510.o
objs-y$(CONFIG_MACH_OMAP_OSK) += lcd_osk.o
-objs-y$(CONFIG_MACH_SX1) += lcd_sx1.o
omapfb-objs := $(objs-yy)
diff --git a/drivers/video/omap/lcd_sx1.c b/drivers/video/omap/lcd_sx1.c
deleted file mode 100644
index e55de20..0000000
--- a/drivers/video/omap/lcd_sx1.c
+++ /dev/null
@@ -1,327 +0,0 @@
-/*
- * LCD panel support for the Siemens SX1 mobile phone
- *
- * Current version : Vovan888@gmail.com, great help from FCA00000
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
- * General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
- */
-
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/io.h>
-
-#include <mach/gpio.h>
-#include <mach/omapfb.h>
-#include <mach/mcbsp.h>
-#include <mach/mux.h>
-
-/*
- * OMAP310 GPIO registers
- */
-#define GPIO_DATA_INPUT 0xfffce000
-#define GPIO_DATA_OUTPUT 0xfffce004
-#define GPIO_DIR_CONTROL 0xfffce008
-#define GPIO_INT_CONTROL 0xfffce00c
-#define GPIO_INT_MASK 0xfffce010
-#define GPIO_INT_STATUS 0xfffce014
-#define GPIO_PIN_CONTROL 0xfffce018
-
-
-#define A_LCD_SSC_RD 3
-#define A_LCD_SSC_SD 7
-#define _A_LCD_RESET 9
-#define _A_LCD_SSC_CS 12
-#define _A_LCD_SSC_A0 13
-
-#define DSP_REG 0xE1017024
-
-const unsigned char INIT_1[12] = {
- 0x1C, 0x02, 0x88, 0x00, 0x1E, 0xE0, 0x00, 0xDC, 0x00, 0x02, 0x00
-};
-
-const unsigned char INIT_2[127] = {
- 0x15, 0x00, 0x29, 0x00, 0x3E, 0x00, 0x51, 0x00,
- 0x65, 0x00, 0x7A, 0x00, 0x8D, 0x00, 0xA1, 0x00,
- 0xB6, 0x00, 0xC7, 0x00, 0xD8, 0x00, 0xEB, 0x00,
- 0xFB, 0x00, 0x0B, 0x01, 0x1B, 0x01, 0x27, 0x01,
- 0x34, 0x01, 0x41, 0x01, 0x4C, 0x01, 0x55, 0x01,
- 0x5F, 0x01, 0x68, 0x01, 0x70, 0x01, 0x78, 0x01,
- 0x7E, 0x01, 0x86, 0x01, 0x8C, 0x01, 0x94, 0x01,
- 0x9B, 0x01, 0xA1, 0x01, 0xA4, 0x01, 0xA9, 0x01,
- 0xAD, 0x01, 0xB2, 0x01, 0xB7, 0x01, 0xBC, 0x01,
- 0xC0, 0x01, 0xC4, 0x01, 0xC8, 0x01, 0xCB, 0x01,
- 0xCF, 0x01, 0xD2, 0x01, 0xD5, 0x01, 0xD8, 0x01,
- 0xDB, 0x01, 0xE0, 0x01, 0xE3, 0x01, 0xE6, 0x01,
- 0xE8, 0x01, 0xEB, 0x01, 0xEE, 0x01, 0xF1, 0x01,
- 0xF3, 0x01, 0xF8, 0x01, 0xF9, 0x01, 0xFC, 0x01,
- 0x00, 0x02, 0x03, 0x02, 0x07, 0x02, 0x09, 0x02,
- 0x0E, 0x02, 0x13, 0x02, 0x1C, 0x02, 0x00
-};
-
-const unsigned char INIT_3[15] = {
- 0x14, 0x26, 0x33, 0x3D, 0x45, 0x4D, 0x53, 0x59,
- 0x5E, 0x63, 0x67, 0x6D, 0x71, 0x78, 0xFF
-};
-
-static void epson_sendbyte(int flag, unsigned char byte)
-{
- int i, shifter = 0x80;
-
- if (!flag)
- gpio_set_value(_A_LCD_SSC_A0, 0);
- mdelay(2);
- gpio_set_value(A_LCD_SSC_RD, 1);
-
- gpio_set_value(A_LCD_SSC_SD, flag);
-
- OMAP_MCBSP_WRITE(OMAP1510_MCBSP3_BASE, PCR0, 0x2200);
- OMAP_MCBSP_WRITE(OMAP1510_MCBSP3_BASE, PCR0, 0x2202);
- for (i = 0; i < 8; i++) {
- OMAP_MCBSP_WRITE(OMAP1510_MCBSP3_BASE, PCR0, 0x2200);
- gpio_set_value(A_LCD_SSC_SD, shifter & byte);
- OMAP_MCBSP_WRITE(OMAP1510_MCBSP3_BASE, PCR0, 0x2202);
- shifter >>= 1;
- }
- gpio_set_value(_A_LCD_SSC_A0, 1);
-}
-
-static void init_system(void)
-{
- omap_mcbsp_request(OMAP_MCBSP3);
- omap_mcbsp_stop(OMAP_MCBSP3);
-}
-
-static void setup_GPIO(void)
-{
- /* new wave */
- gpio_request(A_LCD_SSC_RD, "lcd_ssc_rd");
- gpio_request(A_LCD_SSC_SD, "lcd_ssc_sd");
- gpio_request(_A_LCD_RESET, "lcd_reset");
- gpio_request(_A_LCD_SSC_CS, "lcd_ssc_cs");
- gpio_request(_A_LCD_SSC_A0, "lcd_ssc_a0");
-
- /* set GPIOs to output, with initial data */
- gpio_direction_output(A_LCD_SSC_RD, 1);
- gpio_direction_output(A_LCD_SSC_SD, 0);
- gpio_direction_output(_A_LCD_RESET, 0);
- gpio_direction_output(_A_LCD_SSC_CS, 1);
- gpio_direction_output(_A_LCD_SSC_A0, 1);
-}
-
-static void display_init(void)
-{
- int i;
-
- omap_cfg_reg(MCBSP3_CLKX);
-
- mdelay(2);
- setup_GPIO();
- mdelay(2);
-
- /* reset LCD */
- gpio_set_value(A_LCD_SSC_SD, 1);
- epson_sendbyte(0, 0x25);
-
- gpio_set_value(_A_LCD_RESET, 0);
- mdelay(10);
- gpio_set_value(_A_LCD_RESET, 1);
-
- gpio_set_value(_A_LCD_SSC_CS, 1);
- mdelay(2);
- gpio_set_value(_A_LCD_SSC_CS, 0);
-
- /* init LCD, phase 1 */
- epson_sendbyte(0, 0xCA);
- for (i = 0; i < 10; i++)
- epson_sendbyte(1, INIT_1[i]);
- gpio_set_value(_A_LCD_SSC_CS, 1);
- gpio_set_value(_A_LCD_SSC_CS, 0);
-
- /* init LCD phase 2 */
- epson_sendbyte(0, 0xCB);
- for (i = 0; i < 125; i++)
- epson_sendbyte(1, INIT_2[i]);
- gpio_set_value(_A_LCD_SSC_CS, 1);
- gpio_set_value(_A_LCD_SSC_CS, 0);
-
- /* init LCD phase 2a */
- epson_sendbyte(0, 0xCC);
- for (i = 0; i < 14; i++)
- epson_sendbyte(1, INIT_3[i]);
- gpio_set_value(_A_LCD_SSC_CS, 1);
- gpio_set_value(_A_LCD_SSC_CS, 0);
-
- /* init LCD phase 3 */
- epson_sendbyte(0, 0xBC);
- epson_sendbyte(1, 0x08);
- gpio_set_value(_A_LCD_SSC_CS, 1);
- gpio_set_value(_A_LCD_SSC_CS, 0);
-
- /* init LCD phase 4 */
- epson_sendbyte(0, 0x07);
- epson_sendbyte(1, 0x05);
- gpio_set_value(_A_LCD_SSC_CS, 1);
- gpio_set_value(_A_LCD_SSC_CS, 0);
-
- /* init LCD phase 5 */
- epson_sendbyte(0, 0x94);
- gpio_set_value(_A_LCD_SSC_CS, 1);
- gpio_set_value(_A_LCD_SSC_CS, 0);
-
- /* init LCD phase 6 */
- epson_sendbyte(0, 0xC6);
- epson_sendbyte(1, 0x80);
- gpio_set_value(_A_LCD_SSC_CS, 1);
- mdelay(100); /* used to be 1000 */
- gpio_set_value(_A_LCD_SSC_CS, 0);
-
- /* init LCD phase 7 */
- epson_sendbyte(0, 0x16);
- epson_sendbyte(1, 0x02);
- epson_sendbyte(1, 0x00);
- epson_sendbyte(1, 0xB1);
- epson_sendbyte(1, 0x00);
- gpio_set_value(_A_LCD_SSC_CS, 1);
- gpio_set_value(_A_LCD_SSC_CS, 0);
-
- /* init LCD phase 8 */
- epson_sendbyte(0, 0x76);
- epson_sendbyte(1, 0x00);
- epson_sendbyte(1, 0x00);
- epson_sendbyte(1, 0xDB);
- epson_sendbyte(1, 0x00);
- gpio_set_value(_A_LCD_SSC_CS, 1);
- gpio_set_value(_A_LCD_SSC_CS, 0);
-
- /* init LCD phase 9 */
- epson_sendbyte(0, 0xAF);
- gpio_set_value(_A_LCD_SSC_CS, 1);
-}
-
-static int sx1_panel_init(struct lcd_panel *panel, struct omapfb_device *fbdev)
-{
- return 0;
-}
-
-static void sx1_panel_cleanup(struct lcd_panel *panel)
-{
-}
-
-static void sx1_panel_disable(struct lcd_panel *panel)
-{
- printk(KERN_INFO "SX1: LCD panel disable\n");
- sx1_setmmipower(0);
- gpio_set_value(_A_LCD_SSC_CS, 1);
-
- epson_sendbyte(0, 0x25);
- gpio_set_value(_A_LCD_SSC_CS, 0);
-
- epson_sendbyte(0, 0xAE);
- gpio_set_value(_A_LCD_SSC_CS, 1);
- mdelay(100);
- gpio_set_value(_A_LCD_SSC_CS, 0);
-
- epson_sendbyte(0, 0x95);
- gpio_set_value(_A_LCD_SSC_CS, 1);
-}
-
-static int sx1_panel_enable(struct lcd_panel *panel)
-{
- printk(KERN_INFO "lcd_sx1: LCD panel enable\n");
- init_system();
- display_init();
-
- sx1_setmmipower(1);
- sx1_setbacklight(0x18);
- sx1_setkeylight (0x06);
- return 0;
-}
-
-
-static unsigned long sx1_panel_get_caps(struct lcd_panel *panel)
-{
- return 0;
-}
-
-struct lcd_panel sx1_panel = {
- .name = "sx1",
- .config = OMAP_LCDC_PANEL_TFT | OMAP_LCDC_INV_VSYNC |
- OMAP_LCDC_INV_HSYNC | OMAP_LCDC_INV_PIX_CLOCK |
- OMAP_LCDC_INV_OUTPUT_EN,
-
- .x_res = 176,
- .y_res = 220,
- .data_lines = 16,
- .bpp = 16,
- .hsw = 5,
- .hfp = 5,
- .hbp = 5,
- .vsw = 2,
- .vfp = 1,
- .vbp = 1,
- .pixel_clock = 1500,
-
- .init = sx1_panel_init,
- .cleanup = sx1_panel_cleanup,
- .enable = sx1_panel_enable,
- .disable = sx1_panel_disable,
- .get_caps = sx1_panel_get_caps,
-};
-
-static int sx1_panel_probe(struct platform_device *pdev)
-{
- omapfb_register_panel(&sx1_panel);
- return 0;
-}
-
-static int sx1_panel_remove(struct platform_device *pdev)
-{
- return 0;
-}
-
-static int sx1_panel_suspend(struct platform_device *pdev, pm_message_t mesg)
-{
- return 0;
-}
-
-static int sx1_panel_resume(struct platform_device *pdev)
-{
- return 0;
-}
-
-struct platform_driver sx1_panel_driver = {
- .probe = sx1_panel_probe,
- .remove = sx1_panel_remove,
- .suspend = sx1_panel_suspend,
- .resume = sx1_panel_resume,
- .driver = {
- .name = "lcd_sx1",
- .owner = THIS_MODULE,
- },
-};
-
-static int sx1_panel_drv_init(void)
-{
- return platform_driver_register(&sx1_panel_driver);
-}
-
-static void sx1_panel_drv_cleanup(void)
-{
- platform_driver_unregister(&sx1_panel_driver);
-}
-
-module_init(sx1_panel_drv_init);
-module_exit(sx1_panel_drv_cleanup);
^ permalink raw reply related [flat|nested] only message in thread