From: Ondrej Zary <linux@rainbow-software.org>
To: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Ondrej Zajicek <santiago@crfreenet.org>,
linux-fbdev@vger.kernel.org,
Kernel development list <linux-kernel@vger.kernel.org>
Subject: [PATCH] s3fb: Add Virge/MX (86C260)
Date: Sun, 01 Jul 2012 19:23:33 +0000 [thread overview]
Message-ID: <201207012123.38236.linux@rainbow-software.org> (raw)
Add support for Virge/MX (86C260) chip. Although this is a laptop chip,
there's an AGP card with this chip too.
Tested with AGP card, will probably not work correctly with laptops.
DDC does not work on this card (even in DOS or Windows).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
--- a/drivers/video/s3fb.c
+++ b/drivers/video/s3fb.c
@@ -84,7 +84,7 @@ static const char * const s3_names[] = {"S3 Unknown", "S3 Trio32", "S3 Trio64",
"S3 Virge/VX", "S3 Virge/DX", "S3 Virge/GX",
"S3 Virge/GX2", "S3 Virge/GX2+", "",
"S3 Trio3D/1X", "S3 Trio3D/2X", "S3 Trio3D/2X",
- "S3 Trio3D"};
+ "S3 Trio3D", "S3 Virge/MX"};
#define CHIP_UNKNOWN 0x00
#define CHIP_732_TRIO32 0x01
@@ -105,6 +105,7 @@ static const char * const s3_names[] = {"S3 Unknown", "S3 Trio32", "S3 Trio64",
#define CHIP_362_TRIO3D_2X 0x11
#define CHIP_368_TRIO3D_2X 0x12
#define CHIP_365_TRIO3D 0x13
+#define CHIP_260_VIRGE_MX 0x14
#define CHIP_XXX_TRIO 0x80
#define CHIP_XXX_TRIO64V2_DXGX 0x81
@@ -280,7 +281,8 @@ static int __devinit s3fb_setup_ddc_bus(struct fb_info *info)
*/
/* vga_wseq(par->state.vgabase, 0x08, 0x06); - not needed, already unlocked */
if (par->chip = CHIP_357_VIRGE_GX2 ||
- par->chip = CHIP_359_VIRGE_GX2P)
+ par->chip = CHIP_359_VIRGE_GX2P ||
+ par->chip = CHIP_260_VIRGE_MX)
svga_wseq_mask(par->state.vgabase, 0x0d, 0x01, 0x03);
else
svga_wseq_mask(par->state.vgabase, 0x0d, 0x00, 0x03);
@@ -487,7 +489,8 @@ static void s3_set_pixclock(struct fb_info *info, u32 pixclock)
par->chip = CHIP_359_VIRGE_GX2P ||
par->chip = CHIP_360_TRIO3D_1X ||
par->chip = CHIP_362_TRIO3D_2X ||
- par->chip = CHIP_368_TRIO3D_2X) {
+ par->chip = CHIP_368_TRIO3D_2X ||
+ par->chip = CHIP_260_VIRGE_MX) {
vga_wseq(par->state.vgabase, 0x12, (n - 2) | ((r & 3) << 6)); /* n and two bits of r */
vga_wseq(par->state.vgabase, 0x29, r >> 2); /* remaining highest bit of r */
} else
@@ -690,7 +693,8 @@ static int s3fb_set_par(struct fb_info *info)
par->chip != CHIP_359_VIRGE_GX2P &&
par->chip != CHIP_360_TRIO3D_1X &&
par->chip != CHIP_362_TRIO3D_2X &&
- par->chip != CHIP_368_TRIO3D_2X) {
+ par->chip != CHIP_368_TRIO3D_2X &&
+ par->chip != CHIP_260_VIRGE_MX) {
vga_wcrt(par->state.vgabase, 0x54, 0x18); /* M parameter */
vga_wcrt(par->state.vgabase, 0x60, 0xff); /* N parameter */
vga_wcrt(par->state.vgabase, 0x61, 0xff); /* L parameter */
@@ -739,7 +743,8 @@ static int s3fb_set_par(struct fb_info *info)
par->chip = CHIP_368_TRIO3D_2X ||
par->chip = CHIP_365_TRIO3D ||
par->chip = CHIP_375_VIRGE_DX ||
- par->chip = CHIP_385_VIRGE_GX) {
+ par->chip = CHIP_385_VIRGE_GX ||
+ par->chip = CHIP_260_VIRGE_MX) {
dbytes = info->var.xres * ((bpp+7)/8);
vga_wcrt(par->state.vgabase, 0x91, (dbytes + 7) / 8);
vga_wcrt(par->state.vgabase, 0x90, (((dbytes + 7) / 8) >> 8) | 0x80);
@@ -751,7 +756,8 @@ static int s3fb_set_par(struct fb_info *info)
par->chip = CHIP_359_VIRGE_GX2P ||
par->chip = CHIP_360_TRIO3D_1X ||
par->chip = CHIP_362_TRIO3D_2X ||
- par->chip = CHIP_368_TRIO3D_2X)
+ par->chip = CHIP_368_TRIO3D_2X ||
+ par->chip = CHIP_260_VIRGE_MX)
vga_wcrt(par->state.vgabase, 0x34, 0x00);
else /* enable Data Transfer Position Control (DTPC) */
vga_wcrt(par->state.vgabase, 0x34, 0x10);
@@ -807,7 +813,8 @@ static int s3fb_set_par(struct fb_info *info)
par->chip = CHIP_359_VIRGE_GX2P ||
par->chip = CHIP_360_TRIO3D_1X ||
par->chip = CHIP_362_TRIO3D_2X ||
- par->chip = CHIP_368_TRIO3D_2X)
+ par->chip = CHIP_368_TRIO3D_2X ||
+ par->chip = CHIP_260_VIRGE_MX)
svga_wcrt_mask(par->state.vgabase, 0x67, 0x00, 0xF0);
else {
svga_wcrt_mask(par->state.vgabase, 0x67, 0x10, 0xF0);
@@ -837,7 +844,8 @@ static int s3fb_set_par(struct fb_info *info)
par->chip != CHIP_359_VIRGE_GX2P &&
par->chip != CHIP_360_TRIO3D_1X &&
par->chip != CHIP_362_TRIO3D_2X &&
- par->chip != CHIP_368_TRIO3D_2X)
+ par->chip != CHIP_368_TRIO3D_2X &&
+ par->chip != CHIP_260_VIRGE_MX)
hmul = 2;
}
break;
@@ -864,7 +872,8 @@ static int s3fb_set_par(struct fb_info *info)
par->chip != CHIP_359_VIRGE_GX2P &&
par->chip != CHIP_360_TRIO3D_1X &&
par->chip != CHIP_362_TRIO3D_2X &&
- par->chip != CHIP_368_TRIO3D_2X)
+ par->chip != CHIP_368_TRIO3D_2X &&
+ par->chip != CHIP_260_VIRGE_MX)
hmul = 2;
}
break;
@@ -1208,7 +1217,8 @@ static int __devinit s3_pci_probe(struct pci_dev *dev, const struct pci_device_i
break;
}
} else if (par->chip = CHIP_357_VIRGE_GX2 ||
- par->chip = CHIP_359_VIRGE_GX2P) {
+ par->chip = CHIP_359_VIRGE_GX2P ||
+ par->chip = CHIP_260_VIRGE_MX) {
switch ((regval & 0xC0) >> 6) {
case 1: /* 4MB */
info->screen_size = 4 << 20;
@@ -1515,6 +1525,7 @@ static struct pci_device_id s3_devices[] __devinitdata = {
{PCI_DEVICE(PCI_VENDOR_ID_S3, 0x8A12), .driver_data = CHIP_359_VIRGE_GX2P},
{PCI_DEVICE(PCI_VENDOR_ID_S3, 0x8A13), .driver_data = CHIP_36X_TRIO3D_1X_2X},
{PCI_DEVICE(PCI_VENDOR_ID_S3, 0x8904), .driver_data = CHIP_365_TRIO3D},
+ {PCI_DEVICE(PCI_VENDOR_ID_S3, 0x8C01), .driver_data = CHIP_260_VIRGE_MX},
{0, 0, 0, 0, 0, 0, 0}
};
--
Ondrej Zary
reply other threads:[~2012-07-01 19:23 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=201207012123.38236.linux@rainbow-software.org \
--to=linux@rainbow-software.org \
--cc=FlorianSchandinat@gmx.de \
--cc=linux-fbdev@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=santiago@crfreenet.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).