[PATCH 2/2] backlight: arcxcnn: devicetree bindings for ArticSand devices

[PATCH 2/2] backlight: arcxcnn: devicetree bindings for ArticSand devices

[Olimpiu Dejeu]

Resubmition of arcxcnn backliught driver bindings correcting the file 
 location, device name, and proper use of reg for device address

Signed-off-by: Olimpiu Dejeu <olimpiu@arcticsand.com>

---
 .../bindings/leds/backlight/arcxcnn_bl.txt         | 30 ++++++++++++++++++++++
 .../devicetree/bindings/vendor-prefixes.txt        |  1 +
 2 files changed, 31 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt

diff --git a/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
new file mode 100644
index 0000000..bcf5664
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
@@ -0,0 +1,30 @@
+Binding for ArcticSand arc2c0608 LED driver
+
+Required properties:
+- compatible: should be "arc,arc2c0608"
+- reg: slave address
+
+Optional properties:
+- default-brightness: brightness value on boot, value from: 0-4095
+- label: The name of the backlight device
+			See Documentation/devicetree/bindings/leds/common.txt
+- led-sources: List of enabled channels from 0 to 5.
+			See Documentation/devicetree/bindings/leds/common.txt
+
+Example:
+
+arc2c0608@30 {
+	compatible = "arc,arc2c0608";
+	reg = <0x30>;
+	default-brightness = <500>;
+	label = "lcd-backlight";
+	linux,default-trigger = "backlight";
+	led-sources = <0 1 2 5>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	prog@6 {
+		reg = <0x06>;
+		val = <0x0F>;
+	};
+};
+
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 1992aa9..dc8546f 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -27,6 +27,7 @@ analogix	Analogix Semiconductor, Inc.
 apm	Applied Micro Circuits Corporation (APM)
 aptina	Aptina Imaging
 arasan	Arasan Chip Systems
+arc Artic Sand Technologies
 arm	ARM Ltd.
 armadeus	ARMadeus Systems SARL
 arrow	Arrow Electronics
-- 
2.7.4

Re: [PATCH 2/2] backlight: arcxcnn: devicetree bindings for ArticSand devices

[Mark Rutland]

On Thu, Sep 29, 2016 at 12:35:37PM -0400, Olimpiu Dejeu wrote:
> Resubmition of arcxcnn backliught driver bindings correcting the file 
>  location, device name, and proper use of reg for device address
> 
> Signed-off-by: Olimpiu Dejeu <olimpiu@arcticsand.com>
> 
> ---
>  .../bindings/leds/backlight/arcxcnn_bl.txt         | 30 ++++++++++++++++++++++
>  .../devicetree/bindings/vendor-prefixes.txt        |  1 +
>  2 files changed, 31 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
> 
> diff --git a/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
> new file mode 100644
> index 0000000..bcf5664
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
> @@ -0,0 +1,30 @@
> +Binding for ArcticSand arc2c0608 LED driver
> +
> +Required properties:
> +- compatible: should be "arc,arc2c0608"
> +- reg: slave address
> +
> +Optional properties:
> +- default-brightness: brightness value on boot, value from: 0-4095
> +- label: The name of the backlight device
> +			See Documentation/devicetree/bindings/leds/common.txt
> +- led-sources: List of enabled channels from 0 to 5.
> +			See Documentation/devicetree/bindings/leds/common.txt
> +
> +Example:
> +
> +arc2c0608@30 {
> +	compatible = "arc,arc2c0608";
> +	reg = <0x30>;
> +	default-brightness = <500>;
> +	label = "lcd-backlight";
> +	linux,default-trigger = "backlight";
> +	led-sources = <0 1 2 5>;
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	prog@6 {
> +		reg = <0x06>;
> +		val = <0x0F>;
> +	};

What is this prog@6 sub-node?

It isn't documented above, and its properties look incredibly suspicious --
this doesn't look right to me.

As a general note, please put binding patches earlier in the series than the
code implementing them, as per
Documentation/devicetree/bindings/submitting-patches.txt.

Thanks,
Mark.

[PATCH 2/2] backlight: arcxcnn: devicetree bindings for ArticSand devices

[Olimpiu Dejeu]

Resubmition of arcxcnn backliught driver bindings with added register
 documentation

Signed-off-by: Olimpiu Dejeu <olimpiu@arcticsand.com>

---
 .../bindings/leds/backlight/arcxcnn_bl.txt         | 31 ++++++++++++++++++++++
 1 file changed, 31 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt

diff --git a/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
new file mode 100644
index 0000000..a7b6ff2
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
@@ -0,0 +1,31 @@
+Binding for ArcticSand arc2c0608 LED driver
+
+Required properties:
+- compatible: should be "arc,arc2c0608"
+- reg: slave address
+
+Optional properties:
+- default-brightness: brightness value on boot, value from: 0-4095
+- label: The name of the backlight device
+			See Documentation/devicetree/bindings/leds/common.txt
+- led-sources: List of enabled channels from 0 to 5.
+			See Documentation/devicetree/bindings/leds/common.txt
+
+- arcticsand,led-config-0: setting for register ILED_CONFIG_0
+- arcticsand,led-config-1: setting for register ILED_CONFIG_1
+- arcticsand,dim-freq: PWM mode frequence setting (bits [3:0] used)
+- arcticsand,comp-config: setting for register CONFIG_COMP
+- arcticsand,filter-config: setting for register FILTER_CONFIG
+- arcticsand,trim-config: setting for register IMAXTUNE
+
+Example:
+
+arc2c0608@30 {
+	compatible = "arc,arc2c0608";
+	reg = <0x30>;
+	default-brightness = <500>;
+	label = "lcd-backlight";
+	linux,default-trigger = "backlight";
+	led-sources = <0 1 2 5>;
+};
+
-- 
2.7.4

Re: [PATCH 2/2] backlight: arcxcnn: devicetree bindings for ArticSand devices

[Rob Herring]

On Wed, Oct 26, 2016 at 04:30:01PM -0400, Olimpiu Dejeu wrote:
> Resubmition of arcxcnn backliught driver bindings with added register
>  documentation
> 
> Signed-off-by: Olimpiu Dejeu <olimpiu@arcticsand.com>
> 
> ---
>  .../bindings/leds/backlight/arcxcnn_bl.txt         | 31 ++++++++++++++++++++++
>  1 file changed, 31 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
> 
> diff --git a/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
> new file mode 100644
> index 0000000..a7b6ff2
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
> @@ -0,0 +1,31 @@
> +Binding for ArcticSand arc2c0608 LED driver
> +
> +Required properties:
> +- compatible: should be "arc,arc2c0608"

What's the correct vendor prefix? arc or arcticsand used below?

> +- reg: slave address
> +
> +Optional properties:
> +- default-brightness: brightness value on boot, value from: 0-4095
> +- label: The name of the backlight device
> +			See Documentation/devicetree/bindings/leds/common.txt
> +- led-sources: List of enabled channels from 0 to 5.
> +			See Documentation/devicetree/bindings/leds/common.txt
> +
> +- arcticsand,led-config-0: setting for register ILED_CONFIG_0
> +- arcticsand,led-config-1: setting for register ILED_CONFIG_1
> +- arcticsand,dim-freq: PWM mode frequence setting (bits [3:0] used)
> +- arcticsand,comp-config: setting for register CONFIG_COMP
> +- arcticsand,filter-config: setting for register FILTER_CONFIG
> +- arcticsand,trim-config: setting for register IMAXTUNE

What are the default values if not present?

What determines these settings? If the board design, then okay. If a 
an enduser wants to adjust, then they shouldn't be in DT.

> +
> +Example:
> +
> +arc2c0608@30 {
> +	compatible = "arc,arc2c0608";
> +	reg = <0x30>;
> +	default-brightness = <500>;
> +	label = "lcd-backlight";
> +	linux,default-trigger = "backlight";
> +	led-sources = <0 1 2 5>;
> +};
> +
> -- 
> 2.7.4
> 

[PATCH 2/2] backlight: arcxcnn: devicetree bindings for ArticSand devices

[Olimpiu Dejeu]

Resubmition of arcxcnn backliught driver addressing the naming convention
 concerns raised by Rob H. Note that all the device tree properties are
 determined by the board design or IC EPROM settings and are not intended
 to be user adjustable.

Signed-off-by: Olimpiu Dejeu <olimpiu@arcticsand.com>

---
 .../bindings/leds/backlight/arcxcnn_bl.txt         | 31 ++++++++++++++++++++++
 1 file changed, 31 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt

diff --git a/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
new file mode 100644
index 0000000..a7b6ff2
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
@@ -0,0 +1,33 @@
+Binding for ArcticSand arc2c0608 LED driver
+
+Required properties:
+- compatible: should be "arc,arc2c0608"
+- reg: slave address
+
+Optional properties:
+- default-brightness: brightness value on boot, value from: 0-4095
+- label: The name of the backlight device
+			See Documentation/devicetree/bindings/leds/common.txt
+- led-sources: List of enabled channels from 0 to 5.
+			See Documentation/devicetree/bindings/leds/common.txt
+
+- arc,led-config-0: setting for register ILED_CONFIG_0
+- arc,led-config-1: setting for register ILED_CONFIG_1
+- arc,dim-freq: PWM mode frequence setting (bits [3:0] used)
+- arc,comp-config: setting for register CONFIG_COMP
+- arc,filter-config: setting for register FILTER_CONFIG
+- arc,trim-config: setting for register IMAXTUNE
+
+Note: Optional properties not specified will default to values in IC EPROM
+
+Example:
+
+arc2c0608@30 {
+	compatible = "arc,arc2c0608";
+	reg = <0x30>;
+	default-brightness = <500>;
+	label = "lcd-backlight";
+	linux,default-trigger = "backlight";
+	led-sources = <0 1 2 5>;
+};
+
-- 
2.7.4

Re: [PATCH 2/2] backlight: arcxcnn: devicetree bindings for ArticSand devices

[Rob Herring]

On Thu, Nov 03, 2016 at 02:29:28PM -0400, Olimpiu Dejeu wrote:
> Resubmition of arcxcnn backliught driver addressing the naming convention

s/Resubmition/Re-submission/
s/backliught/backlight/

>  concerns raised by Rob H. Note that all the device tree properties are
>  determined by the board design or IC EPROM settings and are not intended
>  to be user adjustable.
> 
> Signed-off-by: Olimpiu Dejeu <olimpiu@arcticsand.com>
> 
> ---
>  .../bindings/leds/backlight/arcxcnn_bl.txt         | 31 ++++++++++++++++++++++
>  1 file changed, 31 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt

With that,

Acked-by: Rob Herring <robh@kernel.org>

[PATCH 2/2] backlight: arcxcnn: devicetree bindings for ArticSand devices

[Olimpiu Dejeu]

Resubmition of arcxcnn backlight driver addressing the naming convention
 concerns raised by Rob H. Note that all the device tree properties are
 determined by the board design or IC EPROM settings and are not intended
 to be user adjustable.

Signed-off-by: Olimpiu Dejeu <olimpiu@arcticsand.com>

---
 .../bindings/leds/backlight/arcxcnn_bl.txt         | 31 ++++++++++++++++++++++
 1 file changed, 31 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt

diff --git a/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
new file mode 100644
index 0000000..a7b6ff2
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
@@ -0,0 +1,33 @@
+Binding for ArcticSand arc2c0608 LED driver
+
+Required properties:
+- compatible: should be "arc,arc2c0608"
+- reg: slave address
+
+Optional properties:
+- default-brightness: brightness value on boot, value from: 0-4095
+- label: The name of the backlight device
+			See Documentation/devicetree/bindings/leds/common.txt
+- led-sources: List of enabled channels from 0 to 5.
+			See Documentation/devicetree/bindings/leds/common.txt
+
+- arc,led-config-0: setting for register ILED_CONFIG_0
+- arc,led-config-1: setting for register ILED_CONFIG_1
+- arc,dim-freq: PWM mode frequence setting (bits [3:0] used)
+- arc,comp-config: setting for register CONFIG_COMP
+- arc,filter-config: setting for register FILTER_CONFIG
+- arc,trim-config: setting for register IMAXTUNE
+
+Note: Optional properties not specified will default to values in IC EPROM
+
+Example:
+
+arc2c0608@30 {
+	compatible = "arc,arc2c0608";
+	reg = <0x30>;
+	default-brightness = <500>;
+	label = "lcd-backlight";
+	linux,default-trigger = "backlight";
+	led-sources = <0 1 2 5>;
+};
+
-- 
2.7.4

Re: [PATCH 2/2] backlight: arcxcnn: devicetree bindings for ArticSand devices

[Lee Jones]

On Thu, 10 Nov 2016, Olimpiu Dejeu wrote:

> Resubmition of arcxcnn backlight driver addressing the naming convention
>  concerns raised by Rob H. Note that all the device tree properties are
>  determined by the board design or IC EPROM settings and are not intended
>  to be user adjustable.
> 
> Signed-off-by: Olimpiu Dejeu <olimpiu@arcticsand.com>

You've dropped Rob's Ack.

> ---
>  .../bindings/leds/backlight/arcxcnn_bl.txt         | 31 ++++++++++++++++++++++
>  1 file changed, 31 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
> 
> diff --git a/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
> new file mode 100644
> index 0000000..a7b6ff2
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
> @@ -0,0 +1,33 @@
> +Binding for ArcticSand arc2c0608 LED driver
> +
> +Required properties:
> +- compatible: should be "arc,arc2c0608"
> +- reg: slave address
> +
> +Optional properties:
> +- default-brightness: brightness value on boot, value from: 0-4095
> +- label: The name of the backlight device
> +			See Documentation/devicetree/bindings/leds/common.txt
> +- led-sources: List of enabled channels from 0 to 5.
> +			See Documentation/devicetree/bindings/leds/common.txt
> +
> +- arc,led-config-0: setting for register ILED_CONFIG_0
> +- arc,led-config-1: setting for register ILED_CONFIG_1
> +- arc,dim-freq: PWM mode frequence setting (bits [3:0] used)
> +- arc,comp-config: setting for register CONFIG_COMP
> +- arc,filter-config: setting for register FILTER_CONFIG
> +- arc,trim-config: setting for register IMAXTUNE
> +
> +Note: Optional properties not specified will default to values in IC EPROM
> +
> +Example:
> +
> +arc2c0608@30 {
> +	compatible = "arc,arc2c0608";
> +	reg = <0x30>;
> +	default-brightness = <500>;
> +	label = "lcd-backlight";
> +	linux,default-trigger = "backlight";
> +	led-sources = <0 1 2 5>;
> +};
> +

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

[PATCH 2/2] backlight: arcxcnn: devicetree bindings for ArticSand devices

[Olimpiu Dejeu]

Re-submission of arcxcnn backlight driver addressing the naming convention
 concerns raised by Rob H. Note that all the device tree properties are
 determined by the board design or IC EPROM settings and are not intended
 to be user adjustable.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olimpiu Dejeu <olimpiu@arcticsand.com>

---
 .../bindings/leds/backlight/arcxcnn_bl.txt         | 31 ++++++++++++++++++++++
 1 file changed, 31 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt

diff --git a/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
new file mode 100644
index 0000000..a7b6ff2
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
@@ -0,0 +1,33 @@
+Binding for ArcticSand arc2c0608 LED driver
+
+Required properties:
+- compatible: should be "arc,arc2c0608"
+- reg: slave address
+
+Optional properties:
+- default-brightness: brightness value on boot, value from: 0-4095
+- label: The name of the backlight device
+			See Documentation/devicetree/bindings/leds/common.txt
+- led-sources: List of enabled channels from 0 to 5.
+			See Documentation/devicetree/bindings/leds/common.txt
+
+- arc,led-config-0: setting for register ILED_CONFIG_0
+- arc,led-config-1: setting for register ILED_CONFIG_1
+- arc,dim-freq: PWM mode frequence setting (bits [3:0] used)
+- arc,comp-config: setting for register CONFIG_COMP
+- arc,filter-config: setting for register FILTER_CONFIG
+- arc,trim-config: setting for register IMAXTUNE
+
+Note: Optional properties not specified will default to values in IC EPROM
+
+Example:
+
+arc2c0608@30 {
+	compatible = "arc,arc2c0608";
+	reg = <0x30>;
+	default-brightness = <500>;
+	label = "lcd-backlight";
+	linux,default-trigger = "backlight";
+	led-sources = <0 1 2 5>;
+};
+
-- 
2.7.4

Re: [PATCH 2/2] backlight: arcxcnn: devicetree bindings for ArticSand devices

[Lee Jones]

Your subject should look something like [PATCH vX 0/Y]

Where X is the number of times you've submitted this set.

On Fri, 18 Nov 2016, Olimpiu Dejeu wrote:
> Re-submission of arcxcnn backlight driver addressing the naming convention
>  concerns raised by Rob H. Note that all the device tree properties are
>  determined by the board design or IC EPROM settings and are not intended
>  to be user adjustable.

This is a change log, not a commit log.

Here is where you tell us about the patch.

  Read: Documentation/SubmittingPatches
        Documentation/SubmitChecklist

... before submitting again.

> Acked-by: Rob Herring <robh@kernel.org>
> Signed-off-by: Olimpiu Dejeu <olimpiu@arcticsand.com>
> 
> ---

In here (below the ---) you should have a change log which looks like
this:

v3 => v4:
- The changes you made

v2 => v3:
- The changes you made

v1 => v2:
- The changes you made

... etc

>  .../bindings/leds/backlight/arcxcnn_bl.txt         | 31 ++++++++++++++++++++++
>  1 file changed, 31 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
> 
> diff --git a/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
> new file mode 100644
> index 0000000..a7b6ff2
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
> @@ -0,0 +1,33 @@
> +Binding for ArcticSand arc2c0608 LED driver
> +
> +Required properties:
> +- compatible: should be "arc,arc2c0608"
> +- reg: slave address
> +
> +Optional properties:
> +- default-brightness: brightness value on boot, value from: 0-4095
> +- label: The name of the backlight device
> +			See Documentation/devicetree/bindings/leds/common.txt
> +- led-sources: List of enabled channels from 0 to 5.
> +			See Documentation/devicetree/bindings/leds/common.txt
> +
> +- arc,led-config-0: setting for register ILED_CONFIG_0
> +- arc,led-config-1: setting for register ILED_CONFIG_1
> +- arc,dim-freq: PWM mode frequence setting (bits [3:0] used)
> +- arc,comp-config: setting for register CONFIG_COMP
> +- arc,filter-config: setting for register FILTER_CONFIG
> +- arc,trim-config: setting for register IMAXTUNE
> +
> +Note: Optional properties not specified will default to values in IC EPROM
> +
> +Example:
> +
> +arc2c0608@30 {
> +	compatible = "arc,arc2c0608";
> +	reg = <0x30>;
> +	default-brightness = <500>;
> +	label = "lcd-backlight";
> +	linux,default-trigger = "backlight";
> +	led-sources = <0 1 2 5>;
> +};
> +

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog