[PATCH] backlight: ili922x: fix kernel-doc warnings

[Randy Dunlap <rdunlap@infradead.org>]

Convert comments for START_BYTE() and CHECK_FREQ_REG() macros into
kernel-doc notation to avoid these kernel-doc warnings:

drivers/video/backlight/ili922x.c:85: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
 * START_BYTE(id, rs, rw)
drivers/video/backlight/ili922x.c:118: warning: expecting prototype for CHECK_FREQ_REG(spi_device s, spi_transfer x)(). Prototype was for CHECK_FREQ_REG() instead

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Lee Jones <lee@kernel.org>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Helge Deller <deller@gmx.de>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-fbdev@vger.kernel.org
---
 drivers/video/backlight/ili922x.c |   24 ++++++++++++------------
 1 file changed, 12 insertions(+), 12 deletions(-)

diff -- a/drivers/video/backlight/ili922x.c b/drivers/video/backlight/ili922x.c
--- a/drivers/video/backlight/ili922x.c
+++ b/drivers/video/backlight/ili922x.c
@@ -82,13 +82,7 @@
 #define START_RW_READ		1
 
 /**
- * START_BYTE(id, rs, rw)
- *
- * Set the start byte according to the required operation.
- * The start byte is defined as:
- *   ----------------------------------
- *  | 0 | 1 | 1 | 1 | 0 | ID | RS | RW |
- *   ----------------------------------
+ * START_BYTE - Set the start byte according to the required operation.
  * @id: display's id as set by the manufacturer
  * @rs: operation type bit, one of:
  *	  - START_RS_INDEX	set the index register
@@ -96,19 +90,25 @@
  * @rw: read/write operation
  *	 - START_RW_WRITE	write
  *	 - START_RW_READ	read
+ *
+ * The start byte is defined as:
+ *   ----------------------------------
+ *  | 0 | 1 | 1 | 1 | 0 | ID | RS | RW |
+ *   ----------------------------------
  */
 #define START_BYTE(id, rs, rw)	\
 	(0x70 | (((id) & 0x01) << 2) | (((rs) & 0x01) << 1) | ((rw) & 0x01))
 
 /**
- * CHECK_FREQ_REG(spi_device s, spi_transfer x) - Check the frequency
- *	for the SPI transfer. According to the datasheet, the controller
- *	accept higher frequency for the GRAM transfer, but it requires
+ * CHECK_FREQ_REG - Check the frequency for the SPI transfer.
+ * @s: pointer to an SPI device
+ * @x: pointer to the spi_transfer spec (for read/write buffer pair)
+ *
+ *	According to the datasheet, the controller
+ *	accepts a higher frequency for the GRAM transfer, but it requires
  *	lower frequency when the registers are read/written.
  *	The macro sets the frequency in the spi_transfer structure if
  *	the frequency exceeds the maximum value.
- * @s: pointer to an SPI device
- * @x: pointer to the read/write buffer pair
  */
 #define CHECK_FREQ_REG(s, x)	\
 	do {			\