Linux version 2.6.11=Macvin (bgoglin@macvin) (version gcc 3.3.5 (Debian 1:3.3.5-8)) #2 Tue Mar 8 10:20:10 CET 2005 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 00000000000a0000 (usable) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001fe71000 (usable) BIOS-e820: 000000001fe71000 - 000000001fe73000 (ACPI NVS) BIOS-e820: 000000001fe73000 - 000000001fe94000 (ACPI data) BIOS-e820: 000000001fe94000 - 000000001ff00000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved) BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved) 510MB LOWMEM available. On node 0 totalpages: 130673 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 126577 pages, LIFO batch:16 HighMem zone: 0 pages, LIFO batch:1 DMI 2.3 present. ACPI: RSDP (v000 DELL ) @ 0x000feba0 ACPI: RSDT (v001 DELL GX260 0x00000009 ASL 0x00000061) @ 0x000fd509 ACPI: FADT (v001 DELL GX260 0x00000009 ASL 0x00000061) @ 0x000fd541 ACPI: SSDT (v001 DELL st_ex 0x00001000 MSFT 0x0100000d) @ 0xfffdaccc ACPI: MADT (v001 DELL GX260 0x00000009 ASL 0x00000061) @ 0x000fd5b5 ACPI: BOOT (v001 DELL GX260 0x00000009 ASL 0x00000061) @ 0x000fd621 ACPI: ASF! (v016 DELL GX260 0x00000009 ASL 0x00000061) @ 0x000fd649 ACPI: DSDT (v001 DELL dt_ex 0x00001000 MSFT 0x0100000d) @ 0x00000000 ACPI: PM-Timer IO Port: 0x808 Allocating PCI resources starting at 1ff00000 (gap: 1ff00000:ded00000) Built 1 zonelists Kernel command line: BOOT_IMAGE=2.6.11-fb ro root=301 Initializing CPU#0 CPU 0 irqstacks, hard=c045a000 soft=c0459000 PID hash table entries: 2048 (order: 11, 32768 bytes) Detected 2391.541 MHz processor. Using pmtmr for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 513920k/522692k available (2200k kernel code, 8204k reserved, 1044k data, 156k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay loop... 4734.97 BogoMIPS (lpj=2367488) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU0: Intel P4/Xeon Extended MCE MSRs (12) available CPU: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 07 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. ACPI: setting ELCR to 0200 (from 0e08) NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xfbdea, last bus=1 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20050211 ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1 PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *9 10 11 12 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11 12 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 *10 11 12 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 9 10 11 12 15) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 11 devices PnPBIOS: Disabled by ACPI PNP SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing ** PCI interrupts are no longer routed automatically. If this ** causes a device to stop working, it is probably because the ** driver failed to call pci_enable_device(). As a temporary ** workaround, the "pci=routeirq" argument restores the old ** behavior. If this argument makes the device work again, ** please email the output of "lspci" to bjorn.helgaas@hp.com ** so I can fix the driver. pnp: 00:0a: ioport range 0x800-0x85f could not be reserved pnp: 00:0a: ioport range 0xc00-0xc7f has been reserved pnp: 00:0a: ioport range 0x860-0x8ff could not be reserved Simple Boot Flag at 0x7a set to 0x80 Machine check exception polling timer started. devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x0 ACPI: Power Button (FF) [PWRF] Linux agpgart interface v0.100 (c) Dave Jones agpgart: Detected an Intel 845G Chipset. agpgart: Maximum main memory to use for agp memory: 438M agpgart: Detected 892K stolen memory. agpgart: AGP aperture is 128M @ 0xe8000000 [drm] Initialized drm 1.0.0 20040925 intelfb: Framebuffer driver for Intel(R) 830M/845G/852GM/855GM/865G chipsets intelfb: Version 0.9.2 ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 9 PCI: setting IRQ 9 as level-triggered ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 9 (level, low) -> IRQ 9 intelfb: 00:02.0: Intel(R) 845G, aperture size 128MB, stolen memory 892kB intelfb: Mode is interlaced. intelfb: Initial video mode is 1024x768-16@60. Console: switching to colour frame buffer device 128x48 ACPI: PS/2 Keyboard Controller [KBD] at I/O 0x60, 0x64, irq 1 ACPI: PS/2 Mouse Controller [MOU] at irq 12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered Intel(R) PRO/1000 Network Driver - version 5.6.10.1-k2 Copyright (c) 1999-2004 Intel Corporation. ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10 PCI: setting IRQ 10 as level-triggered ACPI: PCI interrupt 0000:01:0c.0[A] -> GSI 10 (level, low) -> IRQ 10 e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ICH4: IDE controller at PCI slot 0000:00:1f.1 PCI: Enabling device 0000:00:1f.1 (0005 -> 0007) ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 10 (level, low) -> IRQ 10 ICH4: chipset revision 1 ICH4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio Probing IDE interface ide0... hda: IC35L060AVV207-0, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: HL-DT-STDVD-ROM GDR8081N, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 Probing IDE interface ide2... Probing IDE interface ide3... Probing IDE interface ide4... Probing IDE interface ide5... hda: max request size: 1024KiB hda: 78125000 sectors (40000 MB) w/1821KiB Cache, CHS=16383/255/63, UDMA(100) hda: cache flushes supported /dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4 < p5 p6 > hdc: ATAPI 24X DVD-ROM drive, 512kB Cache, DMA Uniform CD-ROM driver Revision: 3.20 mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard on isa0060/serio0 input: ImPS/2 Generic Wheel Mouse on isa0060/serio1 input: PC Speaker Advanced Linux Sound Architecture Driver Version 1.0.8 (Thu Jan 13 09:39:32 2005 UTC). ALSA device list: No soundcards found. NET: Registered protocol family 2 IP: routing cache hash table of 4096 buckets, 32Kbytes TCP established hash table entries: 16384 (order: 5, 131072 bytes) TCP bind hash table entries: 16384 (order: 4, 65536 bytes) TCP: Hash tables configured (established 16384 bind 16384) NET: Registered protocol family 1 NET: Registered protocol family 17 ACPI wakeup devices: VBTN PCI0 USB0 USB1 USB2 PCI1 KBD ACPI: (supports S0 S1 S3 S4 S5) VFS: Mounted root (ext2 filesystem) readonly. Freeing unused kernel memory: 156k freed Adding 498004k swap on /dev/hda2. Priority:-1 extents:1 ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11 PCI: setting IRQ 11 as level-triggered ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:1f.5 to 64 intel8x0_measure_ac97_clock: measured 49237 usecs intel8x0: clocking to 48000 kjournald starting. Commit interval 5 seconds EXT3 FS on hda5, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on hda3, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on hda6, internal journal EXT3-fs: mounted filesystem with ordered data mode. ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 3 PCI: setting IRQ 3 as level-triggered ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 3 (level, low) -> IRQ 3 ehci_hcd 0000:00:1d.7: Intel Corp. 82801DB/DBM (ICH4/ICH4-M) USB 2.0 EHCI Controller PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: irq 3, pci mem 0xffa00800 ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 PCI: cache line size of 128 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004 hub 1-0:1.0: USB hub found hub 1-0:1.0: 6 ports detected USB Universal Host Controller Interface driver v2.2 ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 9 (level, low) -> IRQ 9 uhci_hcd 0000:00:1d.0: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: irq 9, io base 0xff80 uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11 ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 11 (level, low) -> IRQ 11 uhci_hcd 0000:00:1d.1: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: irq 11, io base 0xff60 uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 10 (level, low) -> IRQ 10 uhci_hcd 0000:00:1d.2: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: irq 10, io base 0xff40 uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex ip_tables: (C) 2000-2002 Netfilter core team ip_conntrack version 2.1 (4083 buckets, 32664 max) - 212 bytes per conntrack device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky intelfb: ring buffer : space: 8488 wanted 65472 intelfb: lockup - turning off hardware acceleration