From: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
To: Daniel Vetter <daniel@ffwll.ch>
Cc: Petr Mladek <pmladek@suse.com>,
linux-fbdev@vger.kernel.org,
Sergey Senozhatsky <sergey.senozhatsky@gmail.com>,
linux-kernel@vger.kernel.org, dri-devel@lists.freedesktop.org,
Hans de Goede <hdegoede@redhat.com>,
Steven Rostedt <rostedt@goodmis.org>
Subject: Re: [PATCH v4 0/3] console/fbcon: Add support for deferred console takeover
Date: Wed, 27 Jun 2018 09:47:51 +0000 [thread overview]
Message-ID: <66532157.tkLS2buF0U@amdc3058> (raw)
In-Reply-To: <20180627091520.GI13978@phenom.ffwll.local>
On Wednesday, June 27, 2018 11:15:20 AM Daniel Vetter wrote:
> On Tue, Jun 26, 2018 at 08:36:09PM +0200, Hans de Goede wrote:
> > Hi All,
> >
> > Here is v4 of my patch-set, to delay fbcon taking over the console (and
> > binding to fbdev devices) until there actually is some text output to the
> > console. This is intended for use with the "quiet" cmdline option, in
> > combination with a bootloader which leaves the vendor's logo /
> > EFI bootgraphics put up by the firmware intact on the EFI framebuffer.
> >
> > The end goal here is a boot where the firmware shows its boot graphics
> > and these stay in place for a couple of seconds until the GUI loads and
> > the GUI then smoothly takes over the framebuffer without any distruptions.
> >
> > This patch-set spans 2 subsystems.
> >
> > Petr, the printk subsys change is really trivial (1 line addition) can we
> > get your Acked-by for merging all 3 patches through the fbdev tree?
> >
> > Changelog:
> >
> > Changes in v4:
> > -Keep the comments about which fbcon functions need locks in place
> >
> > Changes in v3:
> > -Export is_console_locke() for use in modules (as fbcon may be built as a .ko)
> > -Use WARN_CONSOLE_UNLOCKED() in several places in the fbcon code to assert
> > proper locking (requested by Daniel)
> > -Unregister the fbcon-dummycon-output-notifier on fbcon_exit() (req. by Daniel)
> > -Document the fbcon=nodefer commandline option (req. by Emil)
> >
> > Changes in v2:
> > -Check the whole string when checking for erases in putcs, instead of just
> > the first char
> > -Make dummycon_blank return 1, so that a redraw gets triggered and any text
> > rendered while blanked gets output so that it can trigger a deferred
> > takeover if one is pending
>
> Wrt merging I think it'd be best if we stuff this into drm-misc-next -
> that will increase testing by gpu drivers a lot, instead of a suprise when
> the fbdev pull lands in upstream.
>
> Bart, is that ok with you?
Not really, since there are efifb changes in the queue which depend
on this series I would really prefer to merge all patches through
fbdev tree.
Also fbdev tree is pulled into -next kernels so testing coverage
should be okay (I assume that everybody are testing -next kernels in
addition to their own branches :-)..
> Hans, if Bart acks this you can directly push this imo.
> -Daniel
Best regards,
--
Bartlomiej Zolnierkiewicz
Samsung R&D Institute Poland
Samsung Electronics
next prev parent reply other threads:[~2018-06-27 9:47 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-06-26 18:36 [PATCH v4 0/3] console/fbcon: Add support for deferred console takeover Hans de Goede
2018-06-26 18:36 ` [PATCH v3 1/3] printk: Export is_console_locked Hans de Goede
2018-06-26 18:38 ` Hans de Goede
2018-06-27 1:07 ` Sergey Senozhatsky
2018-06-27 13:31 ` Petr Mladek
2018-06-26 18:36 ` [PATCH v3 2/3] fbcon: Call WARN_CONSOLE_UNLOCKED() where applicable Hans de Goede
2018-06-27 1:09 ` Sergey Senozhatsky
2018-06-26 18:36 ` [PATCH v3 3/3] console/fbcon: Add support for deferred console takeover Hans de Goede
2018-06-28 7:55 ` Daniel Vetter
2018-06-28 8:20 ` Hans de Goede
2018-06-28 8:37 ` Daniel Vetter
2018-06-28 8:58 ` Hans de Goede
2018-06-26 19:14 ` [PATCH v4 0/3] " Steven Rostedt
2018-06-27 9:15 ` Daniel Vetter
2018-06-27 9:47 ` Bartlomiej Zolnierkiewicz [this message]
2018-06-27 11:13 ` Hans de Goede
2018-06-27 14:15 ` Daniel Vetter
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=66532157.tkLS2buF0U@amdc3058 \
--to=b.zolnierkie@samsung.com \
--cc=daniel@ffwll.ch \
--cc=dri-devel@lists.freedesktop.org \
--cc=hdegoede@redhat.com \
--cc=linux-fbdev@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=pmladek@suse.com \
--cc=rostedt@goodmis.org \
--cc=sergey.senozhatsky@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).