From: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
To: linux-fbdev@vger.kernel.org
Subject: [PATCH 4/4 v3] fbdev: sh_mobile_hdmi: add support for E-EDID parsing
Date: Thu, 11 Nov 2010 14:45:09 +0000 [thread overview]
Message-ID: <Pine.LNX.4.64.1011111542180.15747@axis700.grange> (raw)
Many HDMI clients implement enhanced EDID blocks, which often contain
additional supported video modes. This patch implements parsing of such
E-EDID blocks.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
---
v3: no change
v2: no change
drivers/video/sh_mobile_hdmi.c | 60 ++++++++++++++++++++++++++++++++-------
1 files changed, 49 insertions(+), 11 deletions(-)
diff --git a/drivers/video/sh_mobile_hdmi.c b/drivers/video/sh_mobile_hdmi.c
index c474b0bd..b3241dd 100644
--- a/drivers/video/sh_mobile_hdmi.c
+++ b/drivers/video/sh_mobile_hdmi.c
@@ -210,6 +210,9 @@ struct sh_hdmi {
void __iomem *base;
enum hotplug_state hp_state; /* hot-plug status */
bool preprogrammed_mode; /* use a pre-programmed VIC or the external mode */
+ u8 edid_block_addr;
+ u8 edid_segment_nr;
+ u8 edid_blocks;
struct clk *hdmi_clk;
struct device *dev;
struct fb_info *info;
@@ -750,7 +753,38 @@ static int sh_hdmi_read_edid(struct sh_hdmi *hdmi, unsigned long *hdmi_rate,
printk(KERN_CONT "\n");
#endif
- fb_edid_to_monspecs(edid, &hdmi->monspec);
+ if (!hdmi->edid_blocks) {
+ fb_edid_to_monspecs(edid, &hdmi->monspec);
+ hdmi->edid_blocks = edid[126] + 1;
+
+ dev_dbg(hdmi->dev, "%d main modes, %d extension blocks\n",
+ hdmi->monspec.modedb_len, hdmi->edid_blocks - 1);
+ } else {
+ dev_dbg(hdmi->dev, "Extension %u detected, DTD start %u\n",
+ edid[0], edid[2]);
+ fb_edid_add_monspecs(edid, &hdmi->monspec);
+ }
+
+ if (hdmi->edid_blocks > hdmi->edid_segment_nr * 2 +
+ (hdmi->edid_block_addr >> 7) + 1) {
+ /* More blocks to read */
+ if (hdmi->edid_block_addr) {
+ hdmi->edid_block_addr = 0;
+ hdmi->edid_segment_nr++;
+ } else {
+ hdmi->edid_block_addr = 0x80;
+ }
+ /* Set EDID word address */
+ hdmi_write(hdmi, hdmi->edid_block_addr, HDMI_EDID_WORD_ADDRESS);
+ /* Enable EDID interrupt */
+ hdmi_write(hdmi, 0xC6, HDMI_INTERRUPT_MASK_1);
+ /* Set EDID segment pointer - starts reading EDID */
+ hdmi_write(hdmi, hdmi->edid_segment_nr, HDMI_EDID_SEGMENT_POINTER);
+ return -EAGAIN;
+ }
+
+ /* All E-EDID blocks ready */
+ dev_dbg(hdmi->dev, "%d main and extended modes\n", hdmi->monspec.modedb_len);
fb_get_options("sh_mobile_lcdc", &forced);
if (forced && *forced) {
@@ -889,32 +923,34 @@ static irqreturn_t sh_hdmi_hotplug(int irq, void *dev_id)
/* Check, if hot plug & MSENS pin status are both high */
if ((msens & 0xC0) = 0xC0) {
/* Display plug in */
+ hdmi->edid_segment_nr = 0;
+ hdmi->edid_block_addr = 0;
+ hdmi->edid_blocks = 0;
hdmi->hp_state = HDMI_HOTPLUG_CONNECTED;
/* Set EDID word address */
hdmi_write(hdmi, 0x00, HDMI_EDID_WORD_ADDRESS);
- /* Set EDID segment pointer */
- hdmi_write(hdmi, 0x00, HDMI_EDID_SEGMENT_POINTER);
/* Enable EDID interrupt */
hdmi_write(hdmi, 0xC6, HDMI_INTERRUPT_MASK_1);
+ /* Set EDID segment pointer - starts reading EDID */
+ hdmi_write(hdmi, 0x00, HDMI_EDID_SEGMENT_POINTER);
} else if (!(status1 & 0x80)) {
/* Display unplug, beware multiple interrupts */
- if (hdmi->hp_state != HDMI_HOTPLUG_DISCONNECTED)
+ if (hdmi->hp_state != HDMI_HOTPLUG_DISCONNECTED) {
+ hdmi->hp_state = HDMI_HOTPLUG_DISCONNECTED;
schedule_delayed_work(&hdmi->edid_work, 0);
-
- hdmi->hp_state = HDMI_HOTPLUG_DISCONNECTED;
+ }
/* display_off will switch back to mode_a */
}
} else if (status1 & 2) {
/* EDID error interrupt: retry */
/* Set EDID word address */
- hdmi_write(hdmi, 0x00, HDMI_EDID_WORD_ADDRESS);
+ hdmi_write(hdmi, hdmi->edid_block_addr, HDMI_EDID_WORD_ADDRESS);
/* Set EDID segment pointer */
- hdmi_write(hdmi, 0x00, HDMI_EDID_SEGMENT_POINTER);
+ hdmi_write(hdmi, hdmi->edid_segment_nr, HDMI_EDID_SEGMENT_POINTER);
} else if (status1 & 4) {
/* Disable EDID interrupt */
hdmi_write(hdmi, 0xC0, HDMI_INTERRUPT_MASK_1);
- hdmi->hp_state = HDMI_HOTPLUG_EDID_DONE;
schedule_delayed_work(&hdmi->edid_work, msecs_to_jiffies(10));
}
@@ -1043,7 +1079,7 @@ static void sh_hdmi_edid_work_fn(struct work_struct *work)
mutex_lock(&hdmi->mutex);
- if (hdmi->hp_state = HDMI_HOTPLUG_EDID_DONE) {
+ if (hdmi->hp_state = HDMI_HOTPLUG_CONNECTED) {
unsigned long parent_rate = 0, hdmi_rate;
/* A device has been plugged in */
@@ -1053,6 +1089,8 @@ static void sh_hdmi_edid_work_fn(struct work_struct *work)
if (ret < 0)
goto out;
+ hdmi->hp_state = HDMI_HOTPLUG_EDID_DONE;
+
/* Reconfigure the clock */
ret = sh_hdmi_clk_configure(hdmi, hdmi_rate, parent_rate);
if (ret < 0)
@@ -1103,7 +1141,7 @@ static void sh_hdmi_edid_work_fn(struct work_struct *work)
}
out:
- if (ret < 0)
+ if (ret < 0 && ret != -EAGAIN)
hdmi->hp_state = HDMI_HOTPLUG_DISCONNECTED;
mutex_unlock(&hdmi->mutex);
--
1.7.2.3
reply other threads:[~2010-11-11 14:45 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=Pine.LNX.4.64.1011111542180.15747@axis700.grange \
--to=g.liakhovetski@gmx.de \
--cc=linux-fbdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).