* [PATCHv9][ 1/3] Input: tsc2007: Add device tree support.
From: Denis Carikli @ 2013-11-08 13:17 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: devicetree@vger.kernel.org
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: linux-input@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
---
ChangeLog v8->v9:
- Added Grant Likely in the Cc list.
- Removed the mention of the pinctrl properties in the documentation.
ChangeLog v7->v8:
- Fixed the lack of x and z fuzz properties.
- The pendown gpio is better documented.
- Added Shawn Guo in the cc list.
---
.../bindings/input/touchscreen/tsc2007.txt | 41 ++++
drivers/input/touchscreen/tsc2007.c | 204 ++++++++++++++++----
2 files changed, 204 insertions(+), 41 deletions(-)
create mode 100644 Documentation/devicetree/bindings/input/touchscreen/tsc2007.txt
diff --git a/Documentation/devicetree/bindings/input/touchscreen/tsc2007.txt b/Documentation/devicetree/bindings/input/touchscreen/tsc2007.txt
new file mode 100644
index 0000000..028aba66d
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/tsc2007.txt
@@ -0,0 +1,41 @@
+* Texas Instruments tsc2007 touchscreen controller
+
+Required properties:
+- compatible: must be "ti,tsc2007".
+- reg: I2C address of the chip.
+- ti,x-plate-ohms: X-plate resistance in ohms.
+
+Optional properties:
+- gpios: the interrupt gpio the chip is connected to (trough the penirq pin).
+ The penirq pin goes to low when the panel is touched.
+ (see GPIO binding[1] for more details).
+- interrupt-parent: the phandle for the gpio controller
+ (see interrupt binding[0]).
+- interrupts: (gpio) interrupt to which the chip is connected
+ (see interrupt binding[0]).
+- ti,max-rt: maximum pressure.
+- ti,fuzzx: specifies the absolute input fuzz x value.
+ If set, it will permit noise in the data up to +- the value given to the fuzz
+ parameter, that is used to filter noise from the event stream.
+- ti,fuzzy: specifies the absolute input fuzz y value.
+- ti,fuzzz: specifies the absolute input fuzz z value.
+- ti,poll-period: how much time to wait(in millisecond) before reading again the
+ values from the tsc2007.
+
+[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+[1]: Documentation/devicetree/bindings/gpio/gpio.txt
+
+Example:
+ &i2c1 {
+ /* ... */
+ tsc2007@49 {
+ compatible = "ti,tsc2007";
+ reg = <0x49>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <0x0 0x8>;
+ gpios = <&gpio4 0 0>;
+ ti,x-plate-ohms = <180>;
+ };
+
+ /* ... */
+ };
diff --git a/drivers/input/touchscreen/tsc2007.c b/drivers/input/touchscreen/tsc2007.c
index 0b67ba4..3168a99 100644
--- a/drivers/input/touchscreen/tsc2007.c
+++ b/drivers/input/touchscreen/tsc2007.c
@@ -26,6 +26,9 @@
#include <linux/interrupt.h>
#include <linux/i2c.h>
#include <linux/i2c/tsc2007.h>
+#include <linux/of_device.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
#define TSC2007_MEASURE_TEMP0 (0x0 << 4)
#define TSC2007_MEASURE_AUX (0x2 << 4)
@@ -74,7 +77,12 @@ struct tsc2007 {
u16 max_rt;
unsigned long poll_delay;
unsigned long poll_period;
+ int fuzzx;
+ int fuzzy;
+ int fuzzz;
+ char of;
+ unsigned gpio;
int irq;
wait_queue_head_t wait;
@@ -84,6 +92,11 @@ struct tsc2007 {
void (*clear_penirq)(void);
};
+static int tsc2007_get_pendown_state_dt(struct tsc2007 *ts)
+{
+ return !gpio_get_value(ts->gpio);
+}
+
static inline int tsc2007_xfer(struct tsc2007 *tsc, u8 cmd)
{
s32 data;
@@ -142,6 +155,14 @@ static u32 tsc2007_calculate_pressure(struct tsc2007 *tsc, struct ts_event *tc)
return rt;
}
+static bool tsc2007_is_pen_down_valid(struct tsc2007 *ts)
+{
+ if (ts->of)
+ return gpio_is_valid(ts->gpio);
+ else
+ return ts->get_pendown_state ? true : false;
+}
+
static bool tsc2007_is_pen_down(struct tsc2007 *ts)
{
/*
@@ -158,10 +179,13 @@ static bool tsc2007_is_pen_down(struct tsc2007 *ts)
* to fall back on the pressure reading.
*/
- if (!ts->get_pendown_state)
+ if (!tsc2007_is_pen_down_valid(ts))
return true;
- return ts->get_pendown_state();
+ if (ts->of)
+ return tsc2007_get_pendown_state_dt(ts);
+ else
+ return ts->get_pendown_state();
}
static irqreturn_t tsc2007_soft_irq(int irq, void *handle)
@@ -178,7 +202,7 @@ static irqreturn_t tsc2007_soft_irq(int irq, void *handle)
rt = tsc2007_calculate_pressure(ts, &tc);
- if (rt = 0 && !ts->get_pendown_state) {
+ if (!rt && !tsc2007_is_pen_down_valid(ts)) {
/*
* If pressure reported is 0 and we don't have
* callback to check pendown state, we have to
@@ -228,7 +252,7 @@ static irqreturn_t tsc2007_hard_irq(int irq, void *handle)
{
struct tsc2007 *ts = handle;
- if (!ts->get_pendown_state || likely(ts->get_pendown_state()))
+ if (tsc2007_is_pen_down(ts))
return IRQ_WAKE_THREAD;
if (ts->clear_penirq)
@@ -273,34 +297,71 @@ static void tsc2007_close(struct input_dev *input_dev)
tsc2007_stop(ts);
}
-static int tsc2007_probe(struct i2c_client *client,
- const struct i2c_device_id *id)
+#ifdef CONFIG_OF
+static int tsc2007_probe_dt(struct i2c_client *client, struct tsc2007 *ts,
+ struct device_node *np)
{
- struct tsc2007 *ts;
- struct tsc2007_platform_data *pdata = client->dev.platform_data;
- struct input_dev *input_dev;
- int err;
-
- if (!pdata) {
- dev_err(&client->dev, "platform data is required!\n");
+ int err = 0;
+ u32 val32;
+ u64 val64;
+
+ if (!of_property_read_u32(np, "ti,max-rt", &val32))
+ ts->max_rt = val32;
+ else
+ ts->max_rt = MAX_12BIT;
+
+ if (!of_property_read_u32(np, "ti,fuzzx", &val32))
+ ts->fuzzx = val32;
+
+ if (!of_property_read_u32(np, "ti,fuzzy", &val32))
+ ts->fuzzy = val32;
+
+ if (!of_property_read_u32(np, "ti,fuzzz", &val32))
+ ts->fuzzz = val32;
+
+ if (!of_property_read_u64(np, "ti,poll-period", &val64))
+ ts->poll_period = val64;
+ else
+ ts->poll_period = 1;
+
+ if (!of_property_read_u32(np, "ti,x-plate-ohms", &val32)) {
+ ts->x_plate_ohms = val32;
+ } else {
+ dev_err(&client->dev,
+ "Error: lacking ti,x-plate-ohms devicetree property. (err %d).",
+ err);
return -EINVAL;
}
- if (!i2c_check_functionality(client->adapter,
- I2C_FUNC_SMBUS_READ_WORD_DATA))
- return -EIO;
+ ts->gpio = of_get_gpio(np, 0);
+ if (!gpio_is_valid(ts->gpio))
+ dev_err(&client->dev,
+ "GPIO not found (of_get_gpio returned %d)\n",
+ ts->gpio);
- ts = kzalloc(sizeof(struct tsc2007), GFP_KERNEL);
- input_dev = input_allocate_device();
- if (!ts || !input_dev) {
- err = -ENOMEM;
- goto err_free_mem;
- }
+ /* Used to detect if it is probed trough the device tree,
+ * in order to be able to use that information in the IRQ handler.
+ */
+ ts->of = 1;
- ts->client = client;
- ts->irq = client->irq;
- ts->input = input_dev;
- init_waitqueue_head(&ts->wait);
+ return 0;
+}
+#else
+static int tsc2007_probe_dt(struct i2c_client *client, struct tsc2007 *ts,
+ struct device_node *np)
+{
+ return -ENODEV;
+}
+#endif
+
+static int tsc2007_probe_pdev(struct i2c_client *client, struct tsc2007 *ts,
+ struct tsc2007_platform_data *pdata,
+ const struct i2c_device_id *id)
+{
+ if (!pdata) {
+ dev_err(&client->dev, "platform data is required!\n");
+ return -EINVAL;
+ }
ts->model = pdata->model;
ts->x_plate_ohms = pdata->x_plate_ohms;
@@ -309,13 +370,59 @@ static int tsc2007_probe(struct i2c_client *client,
ts->poll_period = pdata->poll_period ? : 1;
ts->get_pendown_state = pdata->get_pendown_state;
ts->clear_penirq = pdata->clear_penirq;
+ ts->fuzzx = pdata->fuzzx;
+ ts->fuzzy = pdata->fuzzy;
+ ts->fuzzz = pdata->fuzzz;
if (pdata->x_plate_ohms = 0) {
dev_err(&client->dev, "x_plate_ohms is not set up in platform data");
- err = -EINVAL;
- goto err_free_mem;
+ return -EINVAL;
}
+ /* Used to detect if it is probed trough the device tree,
+ * in order to be able to use that information in the IRQ handler.
+ */
+ ts->of = 0;
+
+ return 0;
+}
+
+static int tsc2007_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct device_node *np = client->dev.of_node;
+ struct tsc2007_platform_data *pdata = client->dev.platform_data;
+ struct tsc2007 *ts;
+ struct input_dev *input_dev;
+ int err = 0;
+
+ ts = devm_kzalloc(&client->dev, sizeof(struct tsc2007), GFP_KERNEL);
+ if (!ts)
+ return -ENOMEM;
+
+ if (np)
+ err = tsc2007_probe_dt(client, ts, np);
+ else
+ err = tsc2007_probe_pdev(client, ts, pdata, id);
+
+ if (err)
+ return err;
+
+ if (!i2c_check_functionality(client->adapter,
+ I2C_FUNC_SMBUS_READ_WORD_DATA))
+ return -EIO;
+
+ input_dev = input_allocate_device();
+ if (!input_dev) {
+ err = -ENOMEM;
+ goto err_free_input;
+ };
+
+ ts->client = client;
+ ts->irq = client->irq;
+ ts->input = input_dev;
+ init_waitqueue_head(&ts->wait);
+
snprintf(ts->phys, sizeof(ts->phys),
"%s/input0", dev_name(&client->dev));
@@ -331,19 +438,21 @@ static int tsc2007_probe(struct i2c_client *client,
input_dev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_ABS);
input_dev->keybit[BIT_WORD(BTN_TOUCH)] = BIT_MASK(BTN_TOUCH);
- input_set_abs_params(input_dev, ABS_X, 0, MAX_12BIT, pdata->fuzzx, 0);
- input_set_abs_params(input_dev, ABS_Y, 0, MAX_12BIT, pdata->fuzzy, 0);
+ input_set_abs_params(input_dev, ABS_X, 0, MAX_12BIT, ts->fuzzx, 0);
+ input_set_abs_params(input_dev, ABS_Y, 0, MAX_12BIT, ts->fuzzy, 0);
input_set_abs_params(input_dev, ABS_PRESSURE, 0, MAX_12BIT,
- pdata->fuzzz, 0);
+ ts->fuzzz, 0);
- if (pdata->init_platform_hw)
- pdata->init_platform_hw();
+ if (!np) {
+ if (pdata->init_platform_hw)
+ pdata->init_platform_hw();
+ }
err = request_threaded_irq(ts->irq, tsc2007_hard_irq, tsc2007_soft_irq,
IRQF_ONESHOT, client->dev.driver->name, ts);
if (err < 0) {
dev_err(&client->dev, "irq %d busy?\n", ts->irq);
- goto err_free_mem;
+ goto err_free_input;
}
tsc2007_stop(ts);
@@ -358,23 +467,27 @@ static int tsc2007_probe(struct i2c_client *client,
err_free_irq:
free_irq(ts->irq, ts);
- if (pdata->exit_platform_hw)
- pdata->exit_platform_hw();
- err_free_mem:
+ if (!np) {
+ if (pdata->exit_platform_hw)
+ pdata->exit_platform_hw();
+ }
+ err_free_input:
input_free_device(input_dev);
- kfree(ts);
return err;
}
static int tsc2007_remove(struct i2c_client *client)
{
+ struct device_node *np = client->dev.of_node;
struct tsc2007 *ts = i2c_get_clientdata(client);
struct tsc2007_platform_data *pdata = client->dev.platform_data;
free_irq(ts->irq, ts);
- if (pdata->exit_platform_hw)
- pdata->exit_platform_hw();
+ if (!np) {
+ if (pdata->exit_platform_hw)
+ pdata->exit_platform_hw();
+ }
input_unregister_device(ts->input);
kfree(ts);
@@ -389,10 +502,19 @@ static const struct i2c_device_id tsc2007_idtable[] = {
MODULE_DEVICE_TABLE(i2c, tsc2007_idtable);
+#ifdef CONFIG_OF
+static const struct of_device_id tsc2007_of_match[] = {
+ { .compatible = "ti,tsc2007" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, tsc2007_of_match);
+#endif
+
static struct i2c_driver tsc2007_driver = {
.driver = {
.owner = THIS_MODULE,
- .name = "tsc2007"
+ .name = "tsc2007",
+ .of_match_table = of_match_ptr(tsc2007_of_match),
},
.id_table = tsc2007_idtable,
.probe = tsc2007_probe,
--
1.7.9.5
^ permalink raw reply related
* [PATCHv5][ 5/5] ARM: dts: mbimxsd35 Add video and displays support.
From: Denis Carikli @ 2013-11-08 13:01 UTC (permalink / raw)
To: Jean-Christophe Plagniol-Villard
Cc: Tomi Valkeinen, linux-fbdev-u79uwXL29TY76Z2rM5mHXA, Shawn Guo,
Sascha Hauer, devicetree-u79uwXL29TY76Z2rM5mHXA, Denis Carikli,
Rob Herring, Pawel Moll, Mark Rutland, Stephen Warren,
Ian Campbell, Grant Likely, Eric Bénard
In-Reply-To: <1383915693-9422-1-git-send-email-denis-fO0SIAKYzcbQT0dZR+AlfA@public.gmane.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: devicetree@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
---
ChangeLog v4->v5:
- Added Grant Likely and Shawn Guo in the Cc list.
- Adapted to the new non-dma ipu bindings.
ChangeLog v3->v4:
- Shortened the licenses.
- adapted the dts(i) to the new bindings.
ChangeLog v2->v3:
- The dts were adapted to the new DT bindings which looks more like the IPUv3
ones.
---
.../imx35-eukrea-mbimxsd35-baseboard-cmo-qvga.dts | 58 ++++++++++++++++++++
.../imx35-eukrea-mbimxsd35-baseboard-dvi-svga.dts | 47 ++++++++++++++++
.../imx35-eukrea-mbimxsd35-baseboard-dvi-vga.dts | 47 ++++++++++++++++
3 files changed, 152 insertions(+)
create mode 100644 arch/arm/boot/dts/imx35-eukrea-mbimxsd35-baseboard-cmo-qvga.dts
create mode 100644 arch/arm/boot/dts/imx35-eukrea-mbimxsd35-baseboard-dvi-svga.dts
create mode 100644 arch/arm/boot/dts/imx35-eukrea-mbimxsd35-baseboard-dvi-vga.dts
diff --git a/arch/arm/boot/dts/imx35-eukrea-mbimxsd35-baseboard-cmo-qvga.dts b/arch/arm/boot/dts/imx35-eukrea-mbimxsd35-baseboard-cmo-qvga.dts
new file mode 100644
index 0000000..345f560
--- /dev/null
+++ b/arch/arm/boot/dts/imx35-eukrea-mbimxsd35-baseboard-cmo-qvga.dts
@@ -0,0 +1,58 @@
+/*
+ * Copyright 2013 Eukréa Electromatique <denis@eukrea.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include "imx35-eukrea-mbimxsd35-baseboard.dts"
+
+/ {
+ model = "Eukrea MBIMXSD35 with the CMO-QVGA Display";
+ compatible = "eukrea,mbimxsd35-baseboard-cmo-qvga", "eukrea,mbimxsd35-baseboard", "eukrea,cpuimx35", "fsl,imx35";
+
+ cmo_qvga: display@di0 {
+ compatible = "fsl,mx3-parallel-display";
+ regulator-name = "lcd";
+ interface-pix-fmt = "rgb666";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu_disp0>;
+ lcd-supply = <®_lcd_3v3>;
+ model = "CMO-QVGA";
+ display-timings {
+ qvga_timings: 320x240 {
+ clock-frequency = <6500000>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <68>;
+ hfront-porch = <20>;
+ vback-porch = <15>;
+ vfront-porch = <4>;
+ hsync-len = <30>;
+ vsync-len = <3>;
+ };
+ };
+ };
+
+ reg_lcd_3v3: lcd-en {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_lcd_3v3>;
+ regulator-name = "lcd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio1 4 0>;
+ enable-active-high;
+ };
+};
+
+&ipu {
+ display = <&cmo_qvga>;
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx35-eukrea-mbimxsd35-baseboard-dvi-svga.dts b/arch/arm/boot/dts/imx35-eukrea-mbimxsd35-baseboard-dvi-svga.dts
new file mode 100644
index 0000000..1a249d0
--- /dev/null
+++ b/arch/arm/boot/dts/imx35-eukrea-mbimxsd35-baseboard-dvi-svga.dts
@@ -0,0 +1,47 @@
+/*
+ * Copyright 2013 Eukréa Electromatique <denis@eukrea.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include "imx35-eukrea-mbimxsd35-baseboard.dts"
+
+/ {
+ model = "Eukrea MBIMXSD35 with the DVI-SVGA Display";
+ compatible = "eukrea,mbimxsd35-baseboard-dvi-svga", "eukrea,mbimxsd35-baseboard", "eukrea,cpuimx35", "fsl,imx35";
+ dvi_svga: display@di0 {
+ interface-pix-fmt = "rgb666";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu_disp0>;
+ model = "DVI-SVGA";
+ display-timings {
+ svga_timings: 800x600 {
+ clock-frequency = <40000000>;
+ hactive = <800>;
+ vactive = <600>;
+ hback-porch = <75>;
+ hfront-porch = <75>;
+ vback-porch = <7>;
+ vfront-porch = <75>;
+ hsync-len = <7>;
+ vsync-len = <7>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+};
+
+&ipu {
+ display = <&dvi_svga>;
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx35-eukrea-mbimxsd35-baseboard-dvi-vga.dts b/arch/arm/boot/dts/imx35-eukrea-mbimxsd35-baseboard-dvi-vga.dts
new file mode 100644
index 0000000..44a7616
--- /dev/null
+++ b/arch/arm/boot/dts/imx35-eukrea-mbimxsd35-baseboard-dvi-vga.dts
@@ -0,0 +1,47 @@
+/*
+ * Copyright 2013 Eukréa Electromatique <denis@eukrea.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include "imx35-eukrea-mbimxsd35-baseboard.dts"
+
+/ {
+ model = "Eukrea MBIMXSD35 with the DVI-VGA Display";
+ compatible = "eukrea,mbimxsd35-baseboard-dvi-vga", "eukrea,mbimxsd35-baseboard", "eukrea,cpuimx35", "fsl,imx35";
+ dvi_vga: display@di0 {
+ interface-pix-fmt = "rgb666";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu_disp0>;
+ model = "DVI-VGA";
+ display-timings {
+ vga_timings: 640x480 {
+ clock-frequency = <31250000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <100>;
+ hfront-porch = <100>;
+ vback-porch = <7>;
+ vfront-porch = <100>;
+ hsync-len = <7>;
+ vsync-len = <7>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+};
+
+&ipu {
+ display = <&dvi_vga>;
+ status = "okay";
+};
--
1.7.9.5
^ permalink raw reply related
* [PATCHv5][ 4/5] ARM: dts: i.MX35: Add display support.
From: Denis Carikli @ 2013-11-08 13:01 UTC (permalink / raw)
To: Jean-Christophe Plagniol-Villard
Cc: Tomi Valkeinen, linux-fbdev-u79uwXL29TY76Z2rM5mHXA, Shawn Guo,
Sascha Hauer, devicetree-u79uwXL29TY76Z2rM5mHXA, Denis Carikli,
Rob Herring, Pawel Moll, Mark Rutland, Stephen Warren,
Ian Campbell, Grant Likely, Eric Bénard
In-Reply-To: <1383915693-9422-1-git-send-email-denis-fO0SIAKYzcbQT0dZR+AlfA@public.gmane.org>
A pinctrl node for the IPU was also added.
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: devicetree@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
---
ChangeLog v4->v5:
- Added Grant Likely and Shawn Guo in the Cc list.
- Adapted to the new non-dma ipu bindings.
- Adapted to the use of imx35-pingrp.h
- The pinctrl ipu node addition was moved in this commit.
ChangeLog v3->v4:
- Splitted the imx35.dtsi display support (new patch).
---
arch/arm/boot/dts/imx35.dtsi | 13 +++++++++++++
arch/arm/mach-imx/imx35-dt.c | 7 +++++++
2 files changed, 20 insertions(+)
diff --git a/arch/arm/boot/dts/imx35.dtsi b/arch/arm/boot/dts/imx35.dtsi
index 1cf520a..287bf6b 100644
--- a/arch/arm/boot/dts/imx35.dtsi
+++ b/arch/arm/boot/dts/imx35.dtsi
@@ -175,6 +175,12 @@
};
};
+ ipu {
+ pinctrl_ipu_disp0: ipudisp0grp {
+ fsl,pins = <MX35_IPU_PINGRP1>;
+ };
+ };
+
uart1 {
pinctrl_uart1_1: uart1grp-1 {
fsl,pins = <MX35_UART1_PINGRP1>;
@@ -266,6 +272,13 @@
status = "disabled";
};
+ ipu: ipu@53fc0000 {
+ compatible = "fsl,imx35-ipu";
+ reg = <0x53fc0000 0x4000>;
+ clocks = <&clks 55>;
+ status = "disabled";
+ };
+
audmux: audmux@53fc4000 {
compatible = "fsl,imx35-audmux", "fsl,imx31-audmux";
reg = <0x53fc4000 0x4000>;
diff --git a/arch/arm/mach-imx/imx35-dt.c b/arch/arm/mach-imx/imx35-dt.c
index e3def45..6438f292 100644
--- a/arch/arm/mach-imx/imx35-dt.c
+++ b/arch/arm/mach-imx/imx35-dt.c
@@ -16,14 +16,21 @@
#include <asm/mach/time.h>
#include <asm/hardware/cache-l2x0.h>
#include "common.h"
+#include "devices-imx35.h"
#include "mx35.h"
static void __init imx35_dt_init(void)
{
+ struct device_node *np;
mxc_arch_reset_init_dt();
of_platform_populate(NULL, of_default_bus_match_table,
NULL, NULL);
+
+ /* We don't want to export the IPU as DT bindings. */
+ np = of_find_compatible_node(NULL, NULL, "fsl,imx35-ipu");
+ if (of_device_is_available(np))
+ imx35_add_ipu_core();
}
static void __init imx35_timer_init(void)
--
1.7.9.5
^ permalink raw reply related
* [PATCHv5][ 3/5] video: mx3fb: Introduce regulator support.
From: Denis Carikli @ 2013-11-08 13:01 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1383915693-9422-1-git-send-email-denis@eukrea.com>
This commit is based on the following commit by Fabio Estevam:
4344429 video: mxsfb: Introduce regulator support
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
---
ChangeLog v4->v5:
- Added Shawn Guo in the Cc list.
- Rebased to make it apply.
ChangeLog v3->v4:
- Some code style fixes.
- Improved error handling in eremap.
ChangeLog v2->v3:
- The prints are now replaced with non line wrapped prints.
- The regulator retrival has been adapted to the new DT bindings which looks
more like the IPUv3 ones.
- The regulator_is_enabled checks were kept, because regulator_disable do not
do such check.
---
drivers/video/mx3fb.c | 71 ++++++++++++++++++++++++++++++++++++++++++++++++-
1 file changed, 70 insertions(+), 1 deletion(-)
diff --git a/drivers/video/mx3fb.c b/drivers/video/mx3fb.c
index 7620e4f..8cf9c6f 100644
--- a/drivers/video/mx3fb.c
+++ b/drivers/video/mx3fb.c
@@ -27,6 +27,7 @@
#include <linux/clk.h>
#include <linux/mutex.h>
#include <linux/dma/ipu-dma.h>
+#include <linux/regulator/consumer.h>
#include <linux/platform_data/dma-imx.h>
#include <linux/platform_data/video-mx3fb.h>
@@ -269,6 +270,7 @@ struct mx3fb_info {
struct dma_async_tx_descriptor *txd;
dma_cookie_t cookie;
struct scatterlist sg[2];
+ struct regulator *reg_lcd;
struct fb_var_screeninfo cur_var; /* current var info */
};
@@ -1005,6 +1007,7 @@ static void __blank(int blank, struct fb_info *fbi)
struct mx3fb_info *mx3_fbi = fbi->par;
struct mx3fb_data *mx3fb = mx3_fbi->mx3fb;
int was_blank = mx3_fbi->blank;
+ int ret;
mx3_fbi->blank = blank;
@@ -1023,6 +1026,15 @@ static void __blank(int blank, struct fb_info *fbi)
case FB_BLANK_HSYNC_SUSPEND:
case FB_BLANK_NORMAL:
sdc_set_brightness(mx3fb, 0);
+ if (mx3_fbi->reg_lcd) {
+ if (regulator_is_enabled(mx3_fbi->reg_lcd)) {
+ ret = regulator_disable(mx3_fbi->reg_lcd);
+ if (ret)
+ dev_warn(fbi->device,
+ "lcd regulator disable failed with error: %d\n",
+ ret);
+ }
+ }
memset((char *)fbi->screen_base, 0, fbi->fix.smem_len);
/* Give LCD time to update - enough for 50 and 60 Hz */
msleep(25);
@@ -1030,6 +1042,15 @@ static void __blank(int blank, struct fb_info *fbi)
break;
case FB_BLANK_UNBLANK:
sdc_enable_channel(mx3_fbi);
+ if (mx3_fbi->reg_lcd) {
+ if (!regulator_is_enabled(mx3_fbi->reg_lcd)) {
+ ret = regulator_enable(mx3_fbi->reg_lcd);
+ if (ret)
+ dev_warn(fbi->device,
+ "lcd regulator enable failed with error: %d\n",
+ ret);
+ }
+ }
sdc_set_brightness(mx3fb, mx3fb->backlight_level);
break;
}
@@ -1206,6 +1227,7 @@ static int mx3fb_suspend(struct platform_device *pdev, pm_message_t state)
{
struct mx3fb_data *mx3fb = platform_get_drvdata(pdev);
struct mx3fb_info *mx3_fbi = mx3fb->fbi->par;
+ int ret;
console_lock();
fb_set_suspend(mx3fb->fbi, 1);
@@ -1214,7 +1236,15 @@ static int mx3fb_suspend(struct platform_device *pdev, pm_message_t state)
if (mx3_fbi->blank = FB_BLANK_UNBLANK) {
sdc_disable_channel(mx3_fbi);
sdc_set_brightness(mx3fb, 0);
-
+ if (mx3_fbi->reg_lcd) {
+ if (regulator_is_enabled(mx3_fbi->reg_lcd)) {
+ ret = regulator_disable(mx3_fbi->reg_lcd);
+ if (ret)
+ dev_warn(&pdev->dev,
+ "lcd regulator disable failed with error: %d\n",
+ ret);
+ }
+ }
}
return 0;
}
@@ -1226,10 +1256,20 @@ static int mx3fb_resume(struct platform_device *pdev)
{
struct mx3fb_data *mx3fb = platform_get_drvdata(pdev);
struct mx3fb_info *mx3_fbi = mx3fb->fbi->par;
+ int ret;
if (mx3_fbi->blank = FB_BLANK_UNBLANK) {
sdc_enable_channel(mx3_fbi);
sdc_set_brightness(mx3fb, mx3fb->backlight_level);
+ if (mx3_fbi->reg_lcd) {
+ if (!regulator_is_enabled(mx3_fbi->reg_lcd)) {
+ ret = regulator_enable(mx3_fbi->reg_lcd);
+ if (ret)
+ dev_warn(&pdev->dev,
+ "lcd regulator enable failed with error: %d\n",
+ ret);
+ }
+ }
}
console_lock();
@@ -1373,6 +1413,7 @@ static int init_fb_chan(struct mx3fb_data *mx3fb, struct idmac_channel *ichan)
struct mx3fb_platform_data *mx3fb_pdata = dev->platform_data;
struct device_node *np = dev->of_node;
const char *name;
+ const char *regulator_name;
const char *ipu_disp_format;
unsigned int irq;
struct fb_info *fbi;
@@ -1389,6 +1430,9 @@ static int init_fb_chan(struct mx3fb_data *mx3fb, struct idmac_channel *ichan)
return -EINVAL;
}
+ of_property_read_string(display_np, "regulator-name",
+ ®ulator_name);
+
of_property_read_string(display_np, "interface-pix-fmt",
&ipu_disp_format);
if (!ipu_disp_format) {
@@ -1503,6 +1547,25 @@ static int init_fb_chan(struct mx3fb_data *mx3fb, struct idmac_channel *ichan)
if (ret < 0)
goto erfb;
+ /* In dt mode,
+ * using devm_regulator_get would require that the proprety referencing
+ * the regulator phandle has to be inside the mx3fb node.
+ */
+ if (np) {
+ if (regulator_name)
+ mx3fbi->reg_lcd = regulator_get(NULL, regulator_name);
+ } else {
+ mx3fbi->reg_lcd = devm_regulator_get(dev, "lcd");
+ }
+
+ if (IS_ERR(mx3fbi->reg_lcd)) {
+ dev_warn(mx3fb->dev, "Operating without regulator \"lcd\"\n");
+ mx3fbi->reg_lcd = NULL;
+ } else {
+ dev_info(mx3fb->dev, "Using \"%s\" Regulator\n",
+ regulator_name);
+ }
+
return 0;
erfb:
@@ -1557,6 +1620,7 @@ static int mx3fb_probe(struct platform_device *pdev)
struct dma_chan *chan;
struct dma_chan_request rq;
struct device_node *np = dev->of_node;
+ struct mx3fb_info *mx3_fbi;
/*
* Display Interface (DI) and Synchronous Display Controller (SDC)
@@ -1621,6 +1685,11 @@ ersdc0:
dmaengine_put();
iounmap(mx3fb->reg_base);
eremap:
+ if (mx3fb->fbi) {
+ mx3_fbi = mx3fb->fbi->par;
+ if (mx3_fbi->reg_lcd)
+ regulator_put(mx3_fbi->reg_lcd);
+ }
kfree(mx3fb);
dev_err(dev, "mx3fb: failed to register fb\n");
return ret;
--
1.7.9.5
^ permalink raw reply related
* [PATCHv5][ 2/5] video: mx3fb: Add device tree suport.
From: Denis Carikli @ 2013-11-08 13:01 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1383915693-9422-1-git-send-email-denis@eukrea.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: devicetree@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
---
ChangeLog v4->v5:
- Added some people in the Cc list.
- The full ipu register range is now passed to the driver,
the code and the documentation were adapted to it.
- Updated the documentation not to mention the lcd controller, the ipu was
mentioned instead.
- The ipu patch was removed from this patchset, as a consequence the mx3fb code
has been adapted not to expect the dma ipu driver to be probed trough the device tree.
ChangeLog v3->v4:
- Updated bindings.
- Updated documentation accordinly.
- Updated code accordinly.
- Fixed the lack of "ret =" in
of_property_read_string(display_np, "model", &name);
- Supressed some compilation warnings.
ChangeLog v2->v3:
- The device tree bindings were reworked in order to make it look more like the
IPUv3 bindings.
- The interface_pix_fmt property now looks like the IPUv3 one.
---
.../devicetree/bindings/video/fsl,mx3-fb.txt | 44 +++++++
drivers/video/Kconfig | 2 +
drivers/video/mx3fb.c | 123 +++++++++++++++++---
3 files changed, 151 insertions(+), 18 deletions(-)
create mode 100644 Documentation/devicetree/bindings/video/fsl,mx3-fb.txt
diff --git a/Documentation/devicetree/bindings/video/fsl,mx3-fb.txt b/Documentation/devicetree/bindings/video/fsl,mx3-fb.txt
new file mode 100644
index 0000000..c0409a4
--- /dev/null
+++ b/Documentation/devicetree/bindings/video/fsl,mx3-fb.txt
@@ -0,0 +1,44 @@
+Freescale MX3 IPU.
+=========
+
+Required properties:
+- compatible: Should be "fsl,<chip>-ipu". compatible chips include the imx31 and the
+ imx35.
+- reg: should be register base and length as documented in the datasheet.
+- clocks: Handle to the ipu_gate clock.
+- display: Phandle to a "fsl,mx3-parallel-display" compatible display node
+ which is described below.
+
+Example:
+
+ipu: ipu@53fc0000 {
+ compatible = "fsl,imx35-ipu";
+ reg = <0x53fc0000 0x4000>;
+ clocks = <&clks 55>;
+};
+
+Parallel display support
+============
+
+Required properties:
+- compatible: Should be "fsl,mx3-parallel-display".
+- model : The user-visible name of the display.
+
+Optional properties:
+- interface_pix_fmt: How this display is connected to the
+ crtc. Currently supported types: "rgb24", "rgb565", "rgb666".
+
+It can also have an optional timing subnode as described in
+ Documentation/devicetree/bindings/video/display-timing.txt.
+
+Example:
+
+display0: display@di0 {
+ compatible = "fsl,mx3-parallel-display";
+ interface-pix-fmt = "rgb666";
+ model = "CMO-QVGA";
+};
+
+&ipu {
+ display = <&display0>;
+}
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index 84b685f..edcfa33 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -2357,6 +2357,8 @@ config FB_MX3
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
+ select VIDEOMODE_HELPERS
+ select FB_MODE_HELPERS
default y
help
This is a framebuffer device for the i.MX31 LCD Controller. So
diff --git a/drivers/video/mx3fb.c b/drivers/video/mx3fb.c
index cfdb380..7620e4f 100644
--- a/drivers/video/mx3fb.c
+++ b/drivers/video/mx3fb.c
@@ -31,6 +31,8 @@
#include <linux/platform_data/dma-imx.h>
#include <linux/platform_data/video-mx3fb.h>
+#include <video/of_display_timing.h>
+
#include <asm/io.h>
#include <asm/uaccess.h>
@@ -757,11 +759,13 @@ static int __set_par(struct fb_info *fbi, bool lock)
sig_cfg.Hsync_pol = true;
if (fbi->var.sync & FB_SYNC_VERT_HIGH_ACT)
sig_cfg.Vsync_pol = true;
- if (fbi->var.sync & FB_SYNC_CLK_INVERT)
+ if ((fbi->var.sync & FB_SYNC_CLK_INVERT) ||
+ (fbi->var.sync & FB_SYNC_PIXDAT_HIGH_ACT))
sig_cfg.clk_pol = true;
if (fbi->var.sync & FB_SYNC_DATA_INVERT)
sig_cfg.data_pol = true;
- if (fbi->var.sync & FB_SYNC_OE_ACT_HIGH)
+ if ((fbi->var.sync & FB_SYNC_OE_ACT_HIGH) ||
+ (fbi->var.sync & FB_SYNC_DE_HIGH_ACT))
sig_cfg.enable_pol = true;
if (fbi->var.sync & FB_SYNC_CLK_IDLE_EN)
sig_cfg.clkidle_en = true;
@@ -1351,21 +1355,69 @@ static struct fb_info *mx3fb_init_fbinfo(struct device *dev, struct fb_ops *ops)
return fbi;
}
+static int match_dt_disp_data(const char *property)
+{
+ if (!strcmp("rgb666", property))
+ return IPU_DISP_DATA_MAPPING_RGB666;
+ else if (!strcmp("rgb565", property))
+ return IPU_DISP_DATA_MAPPING_RGB565;
+ else if (!strcmp("rgb24", property))
+ return IPU_DISP_DATA_MAPPING_RGB888;
+ else
+ return -EINVAL;
+}
+
static int init_fb_chan(struct mx3fb_data *mx3fb, struct idmac_channel *ichan)
{
struct device *dev = mx3fb->dev;
struct mx3fb_platform_data *mx3fb_pdata = dev->platform_data;
- const char *name = mx3fb_pdata->name;
+ struct device_node *np = dev->of_node;
+ const char *name;
+ const char *ipu_disp_format;
unsigned int irq;
struct fb_info *fbi;
struct mx3fb_info *mx3fbi;
const struct fb_videomode *mode;
int ret, num_modes;
+ struct fb_videomode of_mode;
+ struct device_node *display_np;
+
+ if (np) {
+ display_np = of_parse_phandle(np, "display", 0);
+ if (!display_np) {
+ dev_err(dev, "Can't get the display device node.\n");
+ return -EINVAL;
+ }
+
+ of_property_read_string(display_np, "interface-pix-fmt",
+ &ipu_disp_format);
+ if (!ipu_disp_format) {
+ mx3fb->disp_data_fmt = IPU_DISP_DATA_MAPPING_RGB666;
+ dev_warn(dev,
+ "ipu display data mapping was not defined, using the default rgb666.\n");
+ } else {
+ mx3fb->disp_data_fmt + match_dt_disp_data(ipu_disp_format);
+ }
+
+ if (mx3fb->disp_data_fmt = -EINVAL) {
+ dev_err(dev, "Illegal display data format \"%s\"\n",
+ ipu_disp_format);
+ return -EINVAL;
+ }
- if (mx3fb_pdata->disp_data_fmt >= ARRAY_SIZE(di_mappings)) {
- dev_err(dev, "Illegal display data format %d\n",
+ ret = of_property_read_string(display_np, "model", &name);
+ if (ret) {
+ dev_err(dev, "Missing display model name\n");
+ return -EINVAL;
+ }
+ } else {
+ name = mx3fb_pdata->name;
+ if (mx3fb_pdata->disp_data_fmt >= ARRAY_SIZE(di_mappings)) {
+ dev_err(dev, "Illegal display data format %d\n",
mx3fb_pdata->disp_data_fmt);
- return -EINVAL;
+ return -EINVAL;
+ }
}
ichan->client = mx3fb;
@@ -1386,12 +1438,24 @@ static int init_fb_chan(struct mx3fb_data *mx3fb, struct idmac_channel *ichan)
goto emode;
}
- if (mx3fb_pdata->mode && mx3fb_pdata->num_modes) {
- mode = mx3fb_pdata->mode;
- num_modes = mx3fb_pdata->num_modes;
+ if (np) {
+ ret = of_get_fb_videomode(display_np, &of_mode,
+ OF_USE_NATIVE_MODE);
+ if (!ret) {
+ mode = &of_mode;
+ num_modes = 1;
+ } else {
+ mode = mx3fb_modedb;
+ num_modes = ARRAY_SIZE(mx3fb_modedb);
+ }
} else {
- mode = mx3fb_modedb;
- num_modes = ARRAY_SIZE(mx3fb_modedb);
+ if (mx3fb_pdata->mode || !mx3fb_pdata->num_modes) {
+ mode = mx3fb_pdata->mode;
+ num_modes = mx3fb_pdata->num_modes;
+ } else {
+ mode = mx3fb_modedb;
+ num_modes = ARRAY_SIZE(mx3fb_modedb);
+ }
}
if (!fb_find_mode(&fbi->var, fbi, fb_mode, mode,
@@ -1421,7 +1485,8 @@ static int init_fb_chan(struct mx3fb_data *mx3fb, struct idmac_channel *ichan)
mx3fbi->mx3fb = mx3fb;
mx3fbi->blank = FB_BLANK_NORMAL;
- mx3fb->disp_data_fmt = mx3fb_pdata->disp_data_fmt;
+ if (!np)
+ mx3fb->disp_data_fmt = mx3fb_pdata->disp_data_fmt;
init_completion(&mx3fbi->flip_cmpl);
disable_irq(ichan->eof_irq);
@@ -1455,17 +1520,21 @@ static bool chan_filter(struct dma_chan *chan, void *arg)
struct device *dev;
struct mx3fb_platform_data *mx3fb_pdata;
- if (!imx_dma_is_ipu(chan))
- return false;
-
if (!rq)
return false;
dev = rq->mx3fb->dev;
mx3fb_pdata = dev->platform_data;
- return rq->id = chan->chan_id &&
- mx3fb_pdata->dma_dev = chan->device->dev;
+ if (!imx_dma_is_ipu(chan) && mx3fb_pdata)
+ return false;
+
+ /* When using the devicetree, mx3fb_pdata is NULL */
+ if (mx3fb_pdata)
+ return rq->id = chan->chan_id &&
+ mx3fb_pdata->dma_dev = chan->device->dev;
+ else
+ return rq->id = chan->chan_id;
}
static void release_fbi(struct fb_info *fbi)
@@ -1487,6 +1556,7 @@ static int mx3fb_probe(struct platform_device *pdev)
dma_cap_mask_t mask;
struct dma_chan *chan;
struct dma_chan_request rq;
+ struct device_node *np = dev->of_node;
/*
* Display Interface (DI) and Synchronous Display Controller (SDC)
@@ -1508,7 +1578,16 @@ static int mx3fb_probe(struct platform_device *pdev)
goto eremap;
}
- pr_debug("Remapped %pR at %p\n", sdc_reg, mx3fb->reg_base);
+ /* The full IPU registers range is passed by the device tree,
+ * whereas the platform data only passes the SDC registers range.
+ */
+ if (np) {
+ mx3fb->reg_base += MX3FB_REG_OFFSET;
+ pr_debug("Remapped %pR at %p\n", sdc_reg + MX3FB_REG_OFFSET,
+ mx3fb->reg_base);
+ } else {
+ pr_debug("Remapped %pR at %p\n", sdc_reg, mx3fb->reg_base);
+ }
/* IDMAC interface */
dmaengine_get();
@@ -1565,9 +1644,17 @@ static int mx3fb_remove(struct platform_device *dev)
return 0;
}
+static struct of_device_id mx3fb_of_dev_id[] = {
+ { .compatible = "fsl,imx31-ipu", },
+ { .compatible = "fsl,imx35-ipu", },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, mx3fb_of_dev_id);
+
static struct platform_driver mx3fb_driver = {
.driver = {
.name = MX3FB_NAME,
+ .of_match_table = mx3fb_of_dev_id,
.owner = THIS_MODULE,
},
.probe = mx3fb_probe,
--
1.7.9.5
^ permalink raw reply related
* [PATCHv5][ 1/5] fbdev: Add the lacking FB_SYNC_* for matching the DISPLAY_FLAGS_*
From: Denis Carikli @ 2013-11-08 13:01 UTC (permalink / raw)
To: linux-arm-kernel
Without that fix, drivers using the fb_videomode_from_videomode
function will not be able to get certain information because
some DISPLAY_FLAGS_* have no corresponding FB_SYNC_*.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: devicetree@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
---
ChangeLog v4->v5:
- Added Geert Uytterhoeven, Grant Likely and Shawn Guo in the Cc list.
- Moved the definitions to a non-userspace header.
- Corrected the comment of the second define.
ChangeLog v3->v4:
- Fixed the issue with FB_SYNC_PIXDAT_HIGH_ACT value.
ChangeLog v2->v3:
- Added Jean-Christophe PLAGNIOL-VILLARD's ACK.
---
drivers/video/fbmon.c | 4 ++++
include/linux/fb.h | 3 +++
2 files changed, 7 insertions(+)
diff --git a/drivers/video/fbmon.c b/drivers/video/fbmon.c
index 6103fa6..29a9ed0 100644
--- a/drivers/video/fbmon.c
+++ b/drivers/video/fbmon.c
@@ -1402,6 +1402,10 @@ int fb_videomode_from_videomode(const struct videomode *vm,
fbmode->sync |= FB_SYNC_HOR_HIGH_ACT;
if (vm->flags & DISPLAY_FLAGS_VSYNC_HIGH)
fbmode->sync |= FB_SYNC_VERT_HIGH_ACT;
+ if (vm->flags & DISPLAY_FLAGS_DE_HIGH)
+ fbmode->sync |= FB_SYNC_DE_HIGH_ACT;
+ if (vm->flags & DISPLAY_FLAGS_PIXDATA_POSEDGE)
+ fbmode->sync |= FB_SYNC_PIXDAT_HIGH_ACT;
if (vm->flags & DISPLAY_FLAGS_INTERLACED)
fbmode->vmode |= FB_VMODE_INTERLACED;
if (vm->flags & DISPLAY_FLAGS_DOUBLESCAN)
diff --git a/include/linux/fb.h b/include/linux/fb.h
index ffac70a..cf2ad5d 100644
--- a/include/linux/fb.h
+++ b/include/linux/fb.h
@@ -45,6 +45,9 @@ struct device_node;
#define FB_SIGNAL_SYNC_ON_GREEN 8
#define FB_SIGNAL_SERRATION_ON 16
+#define FB_SYNC_DE_HIGH_ACT 64 /* data enable active high flag */
+#define FB_SYNC_PIXDAT_HIGH_ACT 128 /* drive data on positive edge */
+
#define FB_MISC_PRIM_COLOR 1
#define FB_MISC_1ST_DETAIL 2 /* First Detailed Timing is preferred */
struct fb_chroma {
--
1.7.9.5
^ permalink raw reply related
* re: video: Add Aeroflex Gaisler GRVGA framebuffer device driver
From: Dan Carpenter @ 2013-11-08 10:05 UTC (permalink / raw)
To: linux-fbdev
Hello Kristoffer Glembo,
This is a semi-automatic email about new static checker warnings.
The patch a4b8f97a8fde: "video: Add Aeroflex Gaisler GRVGA
framebuffer device driver" from Jul 5, 2011, leads to the following
Smatch complaint:
drivers/video/grvga.c:519 grvga_remove()
warn: variable dereferenced before check 'info' (see line 517)
drivers/video/grvga.c
516 struct fb_info *info = dev_get_drvdata(&device->dev);
517 struct grvga_par *par = info->par;
^^^^^^^^^
Dereference.
518
519 if (info) {
^^^^^^
Check.
520 unregister_framebuffer(info);
521 fb_dealloc_cmap(&info->cmap);
regards,
dan carpenter
^ permalink raw reply
* [PATCH] ARM: OMAPFB: panel-sony-acx565akm: fix bad unlock balance
From: Aaro Koskinen @ 2013-11-06 21:24 UTC (permalink / raw)
To: Tomi Valkeinen, linux-omap, linux-fbdev
Cc: Eduardo Valentin, Aaro Koskinen, stable
When booting Nokia N900 smartphone with v3.12 + omap2plus_defconfig
(LOCKDEP enabled) and CONFIG_DISPLAY_PANEL_SONY_ACX565AKM enabled,
the following BUG is seen during the boot:
[ 7.302154] ==================[ 7.307128] [ BUG: bad unlock balance detected! ]
[ 7.312103] 3.12.0-los.git-2093492-00120-g5e01dc7 #3 Not tainted
[ 7.318450] -------------------------------------
[ 7.323425] kworker/u2:1/12 is trying to release lock (&ddata->mutex) at:
[ 7.330657] [<c031b760>] acx565akm_enable+0x12c/0x18c
[ 7.335998] but there are no more locks to release!
Fix by removing the extra mutex_unlock().
Reported-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: stable@vger.kernel.org
---
drivers/video/omap2/displays-new/panel-sony-acx565akm.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/video/omap2/displays-new/panel-sony-acx565akm.c b/drivers/video/omap2/displays-new/panel-sony-acx565akm.c
index e6d56f7..72fe2a8 100644
--- a/drivers/video/omap2/displays-new/panel-sony-acx565akm.c
+++ b/drivers/video/omap2/displays-new/panel-sony-acx565akm.c
@@ -616,7 +616,7 @@ static int acx565akm_enable(struct omap_dss_device *dssdev)
mutex_lock(&ddata->mutex);
r = acx565akm_panel_power_on(dssdev);
- mutex_unlock(&ddata->mutex);
+ /* NOTE: acx565akm_panel_power_on() will unlock the mutex. */
if (r)
return r;
--
1.8.4.2
^ permalink raw reply related
* Re: [PATCH -v2] fbdev: sh_mobile_meram: Fix defined but not used compiler warnings
From: Laurent Pinchart @ 2013-11-06 11:57 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1383728247-19294-1-git-send-email-geert@linux-m68k.org>
Hi Geert,
Thank you for the patch.
On Wednesday 06 November 2013 09:57:27 Geert Uytterhoeven wrote:
> If both CONFIG_PM_SLEEP and CONFIG_PM_RUNTIME are not set:
>
> drivers/video/sh_mobile_meram.c:573: warning: ‘sh_mobile_meram_suspend’
> defined but not used drivers/video/sh_mobile_meram.c:597: warning:
> ‘sh_mobile_meram_resume’ defined but not used
>
> Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
and applied to my tree.
> ---
> v2: Both functions are used if CONFIG_PM_SLEEP || CONFIG_PM_RUNTIME,
> as pointed out by Laurent
>
> drivers/video/sh_mobile_meram.c | 2 ++
> 1 file changed, 2 insertions(+)
>
> diff --git a/drivers/video/sh_mobile_meram.c
> b/drivers/video/sh_mobile_meram.c index e0f098562a74..a297de5cc859 100644
> --- a/drivers/video/sh_mobile_meram.c
> +++ b/drivers/video/sh_mobile_meram.c
> @@ -569,6 +569,7 @@ EXPORT_SYMBOL_GPL(sh_mobile_meram_cache_update);
> * Power management
> */
>
> +#if defined(CONFIG_PM_SLEEP) || defined(CONFIG_PM_RUNTIME)
> static int sh_mobile_meram_suspend(struct device *dev)
> {
> struct platform_device *pdev = to_platform_device(dev);
> @@ -611,6 +612,7 @@ static int sh_mobile_meram_resume(struct device *dev)
> meram_write_reg(priv->base, common_regs[i], priv->regs[i]);
> return 0;
> }
> +#endif /* CONFIG_PM_SLEEP || CONFIG_PM_RUNTIME */
>
> static UNIVERSAL_DEV_PM_OPS(sh_mobile_meram_dev_pm_ops,
> sh_mobile_meram_suspend,
--
Regards,
Laurent Pinchart
^ permalink raw reply
* [PATCH -v2] fbdev: sh_mobile_meram: Fix defined but not used compiler warnings
From: Geert Uytterhoeven @ 2013-11-06 8:57 UTC (permalink / raw)
To: linux-arm-kernel
If both CONFIG_PM_SLEEP and CONFIG_PM_RUNTIME are not set:
drivers/video/sh_mobile_meram.c:573: warning: ‘sh_mobile_meram_suspend’ defined but not used
drivers/video/sh_mobile_meram.c:597: warning: ‘sh_mobile_meram_resume’ defined but not used
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
---
v2: Both functions are used if CONFIG_PM_SLEEP || CONFIG_PM_RUNTIME,
as pointed out by Laurent
drivers/video/sh_mobile_meram.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/drivers/video/sh_mobile_meram.c b/drivers/video/sh_mobile_meram.c
index e0f098562a74..a297de5cc859 100644
--- a/drivers/video/sh_mobile_meram.c
+++ b/drivers/video/sh_mobile_meram.c
@@ -569,6 +569,7 @@ EXPORT_SYMBOL_GPL(sh_mobile_meram_cache_update);
* Power management
*/
+#if defined(CONFIG_PM_SLEEP) || defined(CONFIG_PM_RUNTIME)
static int sh_mobile_meram_suspend(struct device *dev)
{
struct platform_device *pdev = to_platform_device(dev);
@@ -611,6 +612,7 @@ static int sh_mobile_meram_resume(struct device *dev)
meram_write_reg(priv->base, common_regs[i], priv->regs[i]);
return 0;
}
+#endif /* CONFIG_PM_SLEEP || CONFIG_PM_RUNTIME */
static UNIVERSAL_DEV_PM_OPS(sh_mobile_meram_dev_pm_ops,
sh_mobile_meram_suspend,
--
1.7.9.5
^ permalink raw reply related
* [PATCHv12][ 3/8] video: Kconfig: Allow more broad selection of the imxfb framebuffer driver.
From: Denis Carikli @ 2013-11-06 8:52 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1383727939-4190-1-git-send-email-denis@eukrea.com>
Without that patch, a user can't select the imxfb driver when the i.MX25 and/or
the i.MX27 device tree board are selected and that no boards that selects
IMX_HAVE_PLATFORM_IMX_FB are compiled in.
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: devicetree@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
---
ChangeLog v10->v11:
- moved my signed-off-by.
ChangeLog v8->v9:
- Added Jean-Christophe PLAGNIOL-VILLARD's ACK.
---
drivers/video/Kconfig | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index 84b685f..f65e577 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -363,7 +363,7 @@ config FB_SA1100
config FB_IMX
tristate "Freescale i.MX1/21/25/27 LCD support"
- depends on FB && IMX_HAVE_PLATFORM_IMX_FB
+ depends on FB && ARCH_MXC
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
--
1.7.9.5
^ permalink raw reply related
* [PATCHv12][ 2/8] video: imxfb: Also add pwmr for the device tree.
From: Denis Carikli @ 2013-11-06 8:52 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1383727939-4190-1-git-send-email-denis@eukrea.com>
pwmr has to be set to get the imxfb backlight work,
though pwmr was only configurable trough the platform data.
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: devicetree@vger.kernel.org
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
---
.../devicetree/bindings/video/fsl,imx-fb.txt | 3 +++
drivers/video/imxfb.c | 2 ++
2 files changed, 5 insertions(+)
diff --git a/Documentation/devicetree/bindings/video/fsl,imx-fb.txt b/Documentation/devicetree/bindings/video/fsl,imx-fb.txt
index 46da08d..ac457ae 100644
--- a/Documentation/devicetree/bindings/video/fsl,imx-fb.txt
+++ b/Documentation/devicetree/bindings/video/fsl,imx-fb.txt
@@ -17,6 +17,9 @@ Required nodes:
Optional properties:
- fsl,dmacr: DMA Control Register value. This is optional. By default, the
register is not modified as recommended by the datasheet.
+- fsl,pwmr: LCDC PWM Contrast Control Register value. That property is
+ optional, but defining it is necessary to get the backlight working. If that
+ property is ommited, the register is zeroed.
- fsl,lscr1: LCDC Sharp Configuration Register value.
Example:
diff --git a/drivers/video/imxfb.c b/drivers/video/imxfb.c
index a2fe8bd..d2447d2 100644
--- a/drivers/video/imxfb.c
+++ b/drivers/video/imxfb.c
@@ -835,6 +835,8 @@ static int imxfb_init_fbinfo(struct platform_device *pdev)
of_property_read_u32(np, "fsl,dmacr", &fbi->dmacr);
+ of_property_read_u32(np, "fsl,pwmr", &fbi->pwmr);
+
/* These two function pointers could be used by some specific
* platforms. */
fbi->lcd_power = NULL;
--
1.7.9.5
^ permalink raw reply related
* [PATCHv12][ 1/8] video: imxfb: Introduce regulator support.
From: Denis Carikli @ 2013-11-06 8:52 UTC (permalink / raw)
To: linux-arm-kernel
This commit is based on the following commit by Fabio Estevam:
4344429 video: mxsfb: Introduce regulator support
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
---
ChangeLog v9->v10:
- Added a return 0; at the end of imxfb_disable_controller.
ChangeLog v8->v9:
- return an error if regulator_{enable,disable} fails in
imxfb_{enable,disable}_controller, and use it.
---
drivers/video/imxfb.c | 55 ++++++++++++++++++++++++++++++++++++++-----------
1 file changed, 43 insertions(+), 12 deletions(-)
diff --git a/drivers/video/imxfb.c b/drivers/video/imxfb.c
index 38733ac..a2fe8bd 100644
--- a/drivers/video/imxfb.c
+++ b/drivers/video/imxfb.c
@@ -28,6 +28,7 @@
#include <linux/cpufreq.h>
#include <linux/clk.h>
#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
#include <linux/dma-mapping.h>
#include <linux/io.h>
#include <linux/math64.h>
@@ -145,6 +146,7 @@ struct imxfb_info {
struct clk *clk_ipg;
struct clk *clk_ahb;
struct clk *clk_per;
+ struct regulator *reg_lcd;
enum imxfb_type devtype;
bool enabled;
@@ -561,14 +563,25 @@ static void imxfb_exit_backlight(struct imxfb_info *fbi)
}
#endif
-static void imxfb_enable_controller(struct imxfb_info *fbi)
+static int imxfb_enable_controller(struct imxfb_info *fbi)
{
+ int ret;
if (fbi->enabled)
- return;
+ return 0;
pr_debug("Enabling LCD controller\n");
+ if (fbi->reg_lcd) {
+ ret = regulator_enable(fbi->reg_lcd);
+ if (ret) {
+ dev_err(&fbi->pdev->dev,
+ "lcd regulator enable failed with error: %d\n",
+ ret);
+ return ret;
+ }
+ }
+
writel(fbi->screen_dma, fbi->regs + LCDC_SSA);
/* panning offset 0 (0 pixel offset) */
@@ -593,12 +606,16 @@ static void imxfb_enable_controller(struct imxfb_info *fbi)
fbi->backlight_power(1);
if (fbi->lcd_power)
fbi->lcd_power(1);
+
+ return 0;
}
-static void imxfb_disable_controller(struct imxfb_info *fbi)
+static int imxfb_disable_controller(struct imxfb_info *fbi)
{
+ int ret;
+
if (!fbi->enabled)
- return;
+ return 0;
pr_debug("Disabling LCD controller\n");
@@ -613,6 +630,17 @@ static void imxfb_disable_controller(struct imxfb_info *fbi)
fbi->enabled = false;
writel(0, fbi->regs + LCDC_RMCR);
+
+ if (fbi->reg_lcd) {
+ ret = regulator_disable(fbi->reg_lcd);
+ if (ret)
+ dev_err(&fbi->pdev->dev,
+ "lcd regulator disable failed with error: %d\n",
+ ret);
+ return ret;
+ }
+
+ return 0;
}
static int imxfb_blank(int blank, struct fb_info *info)
@@ -626,13 +654,12 @@ static int imxfb_blank(int blank, struct fb_info *info)
case FB_BLANK_VSYNC_SUSPEND:
case FB_BLANK_HSYNC_SUSPEND:
case FB_BLANK_NORMAL:
- imxfb_disable_controller(fbi);
- break;
+ return imxfb_disable_controller(fbi);
case FB_BLANK_UNBLANK:
- imxfb_enable_controller(fbi);
- break;
+ return imxfb_enable_controller(fbi);
}
+
return 0;
}
@@ -734,8 +761,7 @@ static int imxfb_suspend(struct platform_device *dev, pm_message_t state)
pr_debug("%s\n", __func__);
- imxfb_disable_controller(fbi);
- return 0;
+ return imxfb_disable_controller(fbi);
}
static int imxfb_resume(struct platform_device *dev)
@@ -745,8 +771,7 @@ static int imxfb_resume(struct platform_device *dev)
pr_debug("%s\n", __func__);
- imxfb_enable_controller(fbi);
- return 0;
+ return imxfb_enable_controller(fbi);
}
#else
#define imxfb_suspend NULL
@@ -1020,6 +1045,12 @@ static int imxfb_probe(struct platform_device *pdev)
goto failed_register;
}
+ fbi->reg_lcd = devm_regulator_get(&pdev->dev, "lcd");
+ if (IS_ERR(fbi->reg_lcd)) {
+ dev_info(&pdev->dev, "No lcd regulator used.\n");
+ fbi->reg_lcd = NULL;
+ }
+
imxfb_enable_controller(fbi);
fbi->pdev = pdev;
#ifdef PWMR_BACKLIGHT_AVAILABLE
--
1.7.9.5
^ permalink raw reply related
* Re: [PATCH v2 19/19] fbdev: sh-mobile-lcdcfb: Enable the driver on all ARM platforms
From: Geert Uytterhoeven @ 2013-11-06 8:46 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1671829.6znfm3IPYO@avalon>
On Wed, Nov 6, 2013 at 1:27 AM, Laurent Pinchart
<laurent.pinchart@ideasonboard.com> wrote:
>> +#ifdef CONFIG_PM_SLEEP
>> static int sh_mobile_meram_suspend(struct device *dev)
>> {
>> struct platform_device *pdev = to_platform_device(dev);
>> @@ -592,7 +593,9 @@ static int sh_mobile_meram_suspend(struct device *dev)
>> }
>> return 0;
>> }
>> +#endif
>>
>> +#ifdef CONFIG_PM_RUNTIME
>> static int sh_mobile_meram_resume(struct device *dev)
>> {
>> struct platform_device *pdev = to_platform_device(dev);
>> @@ -611,6 +614,7 @@ static int sh_mobile_meram_resume(struct device *dev)
>> meram_write_reg(priv->base, common_regs[i], priv->regs[i]);
>> return 0;
>> }
>> +#endif
>>
>> static UNIVERSAL_DEV_PM_OPS(sh_mobile_meram_dev_pm_ops,
>> sh_mobile_meram_suspend,
>
> I'm a bit surprised, looking at the definition of UNIVERSAL_DEV_PM_OPS, I
> would have thought that both functions would be used when either
> CONFIG_PM_SLEEP or CONFIG_PM_RUNTIME is defined. I would thus have guarded
> both functions with #if defined(CONFIG_PM_SLEEP) ||
> defined(CONFIG_PM_RUNTIME).
You're right. I missed that both function pointers are passed to both macros.
Will send v2.
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply
* Re: [PATCH v2 19/19] fbdev: sh-mobile-lcdcfb: Enable the driver on all ARM platforms
From: Laurent Pinchart @ 2013-11-06 0:27 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <alpine.DEB.2.02.1310312039330.13521@ayla.of.borg>
Hi Geert,
Thank you for the patch.
On Thursday 31 October 2013 20:42:52 Geert Uytterhoeven wrote:
> On Tue, 29 Oct 2013, Laurent Pinchart wrote:
> > Renesas ARM platforms are transitioning from single-platform to
> > multi-platform kernels using the new ARCH_SHMOBILE_MULTI. Make the
> > driver available on all ARM platforms to enable it on both ARCH_SHMOBILE
> > and ARCH_SHMOBILE_MULTI, and increase build testing coverage with
> > COMPILE_TEST.
> >
> > diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
> > index 84b685f..32b5c86 100644
> > --- a/drivers/video/Kconfig
> > +++ b/drivers/video/Kconfig
> > @@ -2482,7 +2482,7 @@ endif
> >
> > config FB_SH_MOBILE_MERAM
> >
> > tristate "SuperH Mobile MERAM read ahead support"
> >
> > - depends on (SUPERH || ARCH_SHMOBILE)
> > + depends on (SUPERH || ARM || COMPILE_TEST)
> >
> > select GENERIC_ALLOCATOR
> > ---help---
> >
> > Enable MERAM support for the SuperH controller.
>
> While the below compiler warnings have been seen with sh-randconfig
> before, they're more likely to happen with COMPILE_TEST=y.
> I now see them with e.g. m68k-allmodconfig, so I created a patch.
>
> From 15eb69172457c675cde177a6f742b6f1dabdeb18 Mon Sep 17 00:00:00 2001
> From: Geert Uytterhoeven <geert@linux-m68k.org>
> Date: Thu, 31 Oct 2013 20:35:14 +0100
> Subject: [PATCH] fbdev: sh_mobile_meram: Fix defined but not used compiler
> warnings
> MIME-Version: 1.0
> Content-Type: text/plain; charset=UTF-8
> Content-Transfer-Encoding: 8bit
>
> If CONFIG_PM_SLEEP resp. CONFIG_PM_RUNTIME are not set:
>
> drivers/video/sh_mobile_meram.c:573: warning: ‘sh_mobile_meram_suspend’
> defined but not used drivers/video/sh_mobile_meram.c:597: warning:
> ‘sh_mobile_meram_resume’ defined but not used
>
> Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
> ---
> drivers/video/sh_mobile_meram.c | 4 ++++
> 1 file changed, 4 insertions(+)
>
> diff --git a/drivers/video/sh_mobile_meram.c
> b/drivers/video/sh_mobile_meram.c index e0f098562a74..56a8e47ffceb 100644
> --- a/drivers/video/sh_mobile_meram.c
> +++ b/drivers/video/sh_mobile_meram.c
> @@ -569,6 +569,7 @@ EXPORT_SYMBOL_GPL(sh_mobile_meram_cache_update);
> * Power management
> */
>
> +#ifdef CONFIG_PM_SLEEP
> static int sh_mobile_meram_suspend(struct device *dev)
> {
> struct platform_device *pdev = to_platform_device(dev);
> @@ -592,7 +593,9 @@ static int sh_mobile_meram_suspend(struct device *dev)
> }
> return 0;
> }
> +#endif
>
> +#ifdef CONFIG_PM_RUNTIME
> static int sh_mobile_meram_resume(struct device *dev)
> {
> struct platform_device *pdev = to_platform_device(dev);
> @@ -611,6 +614,7 @@ static int sh_mobile_meram_resume(struct device *dev)
> meram_write_reg(priv->base, common_regs[i], priv->regs[i]);
> return 0;
> }
> +#endif
>
> static UNIVERSAL_DEV_PM_OPS(sh_mobile_meram_dev_pm_ops,
> sh_mobile_meram_suspend,
I'm a bit surprised, looking at the definition of UNIVERSAL_DEV_PM_OPS, I
would have thought that both functions would be used when either
CONFIG_PM_SLEEP or CONFIG_PM_RUNTIME is defined. I would thus have guarded
both functions with #if defined(CONFIG_PM_SLEEP) ||
defined(CONFIG_PM_RUNTIME).
--
Regards,
Laurent Pinchart
^ permalink raw reply
* [PATCHv11][ 3/7] video: Kconfig: Allow more broad selection of the imxfb framebuffer driver.
From: Denis Carikli @ 2013-11-05 14:39 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1383662354-22417-1-git-send-email-denis@eukrea.com>
Without that patch, a user can't select the imxfb driver when the i.MX25 and/or
the i.MX27 device tree board are selected and that no boards that selects
IMX_HAVE_PLATFORM_IMX_FB are compiled in.
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: devicetree@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
---
ChangeLog v10->v11:
- moved my signed-off-by.
ChangeLog v8->v9:
- Added Jean-Christophe PLAGNIOL-VILLARD's ACK.
---
drivers/video/Kconfig | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index 84b685f..f65e577 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -363,7 +363,7 @@ config FB_SA1100
config FB_IMX
tristate "Freescale i.MX1/21/25/27 LCD support"
- depends on FB && IMX_HAVE_PLATFORM_IMX_FB
+ depends on FB && ARCH_MXC
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
--
1.7.9.5
^ permalink raw reply related
* [PATCHv11][ 2/7] video: imxfb: Also add pwmr for the device tree.
From: Denis Carikli @ 2013-11-05 14:39 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1383662354-22417-1-git-send-email-denis@eukrea.com>
pwmr has to be set to get the imxfb backlight work,
though pwmr was only configurable trough the platform data.
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: devicetree@vger.kernel.org
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
---
.../devicetree/bindings/video/fsl,imx-fb.txt | 3 +++
drivers/video/imxfb.c | 2 ++
2 files changed, 5 insertions(+)
diff --git a/Documentation/devicetree/bindings/video/fsl,imx-fb.txt b/Documentation/devicetree/bindings/video/fsl,imx-fb.txt
index 46da08d..ac457ae 100644
--- a/Documentation/devicetree/bindings/video/fsl,imx-fb.txt
+++ b/Documentation/devicetree/bindings/video/fsl,imx-fb.txt
@@ -17,6 +17,9 @@ Required nodes:
Optional properties:
- fsl,dmacr: DMA Control Register value. This is optional. By default, the
register is not modified as recommended by the datasheet.
+- fsl,pwmr: LCDC PWM Contrast Control Register value. That property is
+ optional, but defining it is necessary to get the backlight working. If that
+ property is ommited, the register is zeroed.
- fsl,lscr1: LCDC Sharp Configuration Register value.
Example:
diff --git a/drivers/video/imxfb.c b/drivers/video/imxfb.c
index a2fe8bd..d2447d2 100644
--- a/drivers/video/imxfb.c
+++ b/drivers/video/imxfb.c
@@ -835,6 +835,8 @@ static int imxfb_init_fbinfo(struct platform_device *pdev)
of_property_read_u32(np, "fsl,dmacr", &fbi->dmacr);
+ of_property_read_u32(np, "fsl,pwmr", &fbi->pwmr);
+
/* These two function pointers could be used by some specific
* platforms. */
fbi->lcd_power = NULL;
--
1.7.9.5
^ permalink raw reply related
* [PATCHv11][ 1/7] video: imxfb: Introduce regulator support.
From: Denis Carikli @ 2013-11-05 14:39 UTC (permalink / raw)
To: linux-arm-kernel
This commit is based on the following commit by Fabio Estevam:
4344429 video: mxsfb: Introduce regulator support
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
---
ChangeLog v9->v10:
- Added a return 0; at the end of imxfb_disable_controller.
ChangeLog v8->v9:
- return an error if regulator_{enable,disable} fails in
imxfb_{enable,disable}_controller, and use it.
---
drivers/video/imxfb.c | 55 ++++++++++++++++++++++++++++++++++++++-----------
1 file changed, 43 insertions(+), 12 deletions(-)
diff --git a/drivers/video/imxfb.c b/drivers/video/imxfb.c
index 38733ac..a2fe8bd 100644
--- a/drivers/video/imxfb.c
+++ b/drivers/video/imxfb.c
@@ -28,6 +28,7 @@
#include <linux/cpufreq.h>
#include <linux/clk.h>
#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
#include <linux/dma-mapping.h>
#include <linux/io.h>
#include <linux/math64.h>
@@ -145,6 +146,7 @@ struct imxfb_info {
struct clk *clk_ipg;
struct clk *clk_ahb;
struct clk *clk_per;
+ struct regulator *reg_lcd;
enum imxfb_type devtype;
bool enabled;
@@ -561,14 +563,25 @@ static void imxfb_exit_backlight(struct imxfb_info *fbi)
}
#endif
-static void imxfb_enable_controller(struct imxfb_info *fbi)
+static int imxfb_enable_controller(struct imxfb_info *fbi)
{
+ int ret;
if (fbi->enabled)
- return;
+ return 0;
pr_debug("Enabling LCD controller\n");
+ if (fbi->reg_lcd) {
+ ret = regulator_enable(fbi->reg_lcd);
+ if (ret) {
+ dev_err(&fbi->pdev->dev,
+ "lcd regulator enable failed with error: %d\n",
+ ret);
+ return ret;
+ }
+ }
+
writel(fbi->screen_dma, fbi->regs + LCDC_SSA);
/* panning offset 0 (0 pixel offset) */
@@ -593,12 +606,16 @@ static void imxfb_enable_controller(struct imxfb_info *fbi)
fbi->backlight_power(1);
if (fbi->lcd_power)
fbi->lcd_power(1);
+
+ return 0;
}
-static void imxfb_disable_controller(struct imxfb_info *fbi)
+static int imxfb_disable_controller(struct imxfb_info *fbi)
{
+ int ret;
+
if (!fbi->enabled)
- return;
+ return 0;
pr_debug("Disabling LCD controller\n");
@@ -613,6 +630,17 @@ static void imxfb_disable_controller(struct imxfb_info *fbi)
fbi->enabled = false;
writel(0, fbi->regs + LCDC_RMCR);
+
+ if (fbi->reg_lcd) {
+ ret = regulator_disable(fbi->reg_lcd);
+ if (ret)
+ dev_err(&fbi->pdev->dev,
+ "lcd regulator disable failed with error: %d\n",
+ ret);
+ return ret;
+ }
+
+ return 0;
}
static int imxfb_blank(int blank, struct fb_info *info)
@@ -626,13 +654,12 @@ static int imxfb_blank(int blank, struct fb_info *info)
case FB_BLANK_VSYNC_SUSPEND:
case FB_BLANK_HSYNC_SUSPEND:
case FB_BLANK_NORMAL:
- imxfb_disable_controller(fbi);
- break;
+ return imxfb_disable_controller(fbi);
case FB_BLANK_UNBLANK:
- imxfb_enable_controller(fbi);
- break;
+ return imxfb_enable_controller(fbi);
}
+
return 0;
}
@@ -734,8 +761,7 @@ static int imxfb_suspend(struct platform_device *dev, pm_message_t state)
pr_debug("%s\n", __func__);
- imxfb_disable_controller(fbi);
- return 0;
+ return imxfb_disable_controller(fbi);
}
static int imxfb_resume(struct platform_device *dev)
@@ -745,8 +771,7 @@ static int imxfb_resume(struct platform_device *dev)
pr_debug("%s\n", __func__);
- imxfb_enable_controller(fbi);
- return 0;
+ return imxfb_enable_controller(fbi);
}
#else
#define imxfb_suspend NULL
@@ -1020,6 +1045,12 @@ static int imxfb_probe(struct platform_device *pdev)
goto failed_register;
}
+ fbi->reg_lcd = devm_regulator_get(&pdev->dev, "lcd");
+ if (IS_ERR(fbi->reg_lcd)) {
+ dev_info(&pdev->dev, "No lcd regulator used.\n");
+ fbi->reg_lcd = NULL;
+ }
+
imxfb_enable_controller(fbi);
fbi->pdev = pdev;
#ifdef PWMR_BACKLIGHT_AVAILABLE
--
1.7.9.5
^ permalink raw reply related
* Re: [PATCHv4][ 1/6] fbdev: Add the lacking FB_SYNC_* for matching the DISPLAY_FLAGS_*
From: Russell King - ARM Linux @ 2013-11-05 13:47 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1383581724-14817-1-git-send-email-denis@eukrea.com>
On Mon, Nov 04, 2013 at 05:15:19PM +0100, Denis Carikli wrote:
> Without that fix, drivers using the fb_videomode_from_videomode
> function will not be able to get certain information because
> some DISPLAY_FLAGS_* have no corresponding FB_SYNC_*.
Please describe how userspace knows how to set these flags.
Flags such as the polarity of the hsync and vsync signals are fairly well
defined based upon the display mode, but aren't things like data enable
and the pixel clock edge a property of the attached LCD panel, which is
something that is configured according to the panel which is attached.
In other words, this information should not be passed from userspace, but
should be part of the DT description about the connected panel. So should
be the polarity of the line and frame pulses (iow, hsync and vsync pulses)
in the case of a connected panel.
Moreover, in the case of a connected LCD panel, chances are it can only
support a very limited number of settings, so support for userspace
changing the timings is arguably incorrect from a system point of view.
^ permalink raw reply
* [PATCHv10][ 3/7] video: Kconfig: Allow more broad selection of the imxfb framebuffer driver.
From: Denis Carikli @ 2013-11-05 10:38 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1383647918-27315-1-git-send-email-denis@eukrea.com>
Without that patch, a user can't select the imxfb driver when the i.MX25 and/or
the i.MX27 device tree board are selected and that no boards that selects
IMX_HAVE_PLATFORM_IMX_FB are compiled in.
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: devicetree@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Eric Bénard <eric@eukrea.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
---
ChangeLog v8->v9:
- Added Jean-Christophe PLAGNIOL-VILLARD's ACK.
---
drivers/video/Kconfig | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index 84b685f..f65e577 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -363,7 +363,7 @@ config FB_SA1100
config FB_IMX
tristate "Freescale i.MX1/21/25/27 LCD support"
- depends on FB && IMX_HAVE_PLATFORM_IMX_FB
+ depends on FB && ARCH_MXC
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
--
1.7.9.5
^ permalink raw reply related
* [PATCHv10][ 2/7] video: imxfb: Also add pwmr for the device tree.
From: Denis Carikli @ 2013-11-05 10:38 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1383647918-27315-1-git-send-email-denis@eukrea.com>
pwmr has to be set to get the imxfb backlight work,
though pwmr was only configurable trough the platform data.
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: devicetree@vger.kernel.org
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
---
.../devicetree/bindings/video/fsl,imx-fb.txt | 3 +++
drivers/video/imxfb.c | 2 ++
2 files changed, 5 insertions(+)
diff --git a/Documentation/devicetree/bindings/video/fsl,imx-fb.txt b/Documentation/devicetree/bindings/video/fsl,imx-fb.txt
index 46da08d..ac457ae 100644
--- a/Documentation/devicetree/bindings/video/fsl,imx-fb.txt
+++ b/Documentation/devicetree/bindings/video/fsl,imx-fb.txt
@@ -17,6 +17,9 @@ Required nodes:
Optional properties:
- fsl,dmacr: DMA Control Register value. This is optional. By default, the
register is not modified as recommended by the datasheet.
+- fsl,pwmr: LCDC PWM Contrast Control Register value. That property is
+ optional, but defining it is necessary to get the backlight working. If that
+ property is ommited, the register is zeroed.
- fsl,lscr1: LCDC Sharp Configuration Register value.
Example:
diff --git a/drivers/video/imxfb.c b/drivers/video/imxfb.c
index a2fe8bd..d2447d2 100644
--- a/drivers/video/imxfb.c
+++ b/drivers/video/imxfb.c
@@ -835,6 +835,8 @@ static int imxfb_init_fbinfo(struct platform_device *pdev)
of_property_read_u32(np, "fsl,dmacr", &fbi->dmacr);
+ of_property_read_u32(np, "fsl,pwmr", &fbi->pwmr);
+
/* These two function pointers could be used by some specific
* platforms. */
fbi->lcd_power = NULL;
--
1.7.9.5
^ permalink raw reply related
* [PATCHv10][ 1/7] video: imxfb: Introduce regulator support.
From: Denis Carikli @ 2013-11-05 10:38 UTC (permalink / raw)
To: linux-arm-kernel
This commit is based on the following commit by Fabio Estevam:
4344429 video: mxsfb: Introduce regulator support
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
---
ChangeLog v9->v10:
- Added a return 0; at the end of imxfb_disable_controller.
ChangeLog v8->v9:
- return an error if regulator_{enable,disable} fails in
imxfb_{enable,disable}_controller, and use it.
---
drivers/video/imxfb.c | 55 ++++++++++++++++++++++++++++++++++++++-----------
1 file changed, 43 insertions(+), 12 deletions(-)
diff --git a/drivers/video/imxfb.c b/drivers/video/imxfb.c
index 38733ac..a2fe8bd 100644
--- a/drivers/video/imxfb.c
+++ b/drivers/video/imxfb.c
@@ -28,6 +28,7 @@
#include <linux/cpufreq.h>
#include <linux/clk.h>
#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
#include <linux/dma-mapping.h>
#include <linux/io.h>
#include <linux/math64.h>
@@ -145,6 +146,7 @@ struct imxfb_info {
struct clk *clk_ipg;
struct clk *clk_ahb;
struct clk *clk_per;
+ struct regulator *reg_lcd;
enum imxfb_type devtype;
bool enabled;
@@ -561,14 +563,25 @@ static void imxfb_exit_backlight(struct imxfb_info *fbi)
}
#endif
-static void imxfb_enable_controller(struct imxfb_info *fbi)
+static int imxfb_enable_controller(struct imxfb_info *fbi)
{
+ int ret;
if (fbi->enabled)
- return;
+ return 0;
pr_debug("Enabling LCD controller\n");
+ if (fbi->reg_lcd) {
+ ret = regulator_enable(fbi->reg_lcd);
+ if (ret) {
+ dev_err(&fbi->pdev->dev,
+ "lcd regulator enable failed with error: %d\n",
+ ret);
+ return ret;
+ }
+ }
+
writel(fbi->screen_dma, fbi->regs + LCDC_SSA);
/* panning offset 0 (0 pixel offset) */
@@ -593,12 +606,16 @@ static void imxfb_enable_controller(struct imxfb_info *fbi)
fbi->backlight_power(1);
if (fbi->lcd_power)
fbi->lcd_power(1);
+
+ return 0;
}
-static void imxfb_disable_controller(struct imxfb_info *fbi)
+static int imxfb_disable_controller(struct imxfb_info *fbi)
{
+ int ret;
+
if (!fbi->enabled)
- return;
+ return 0;
pr_debug("Disabling LCD controller\n");
@@ -613,6 +630,17 @@ static void imxfb_disable_controller(struct imxfb_info *fbi)
fbi->enabled = false;
writel(0, fbi->regs + LCDC_RMCR);
+
+ if (fbi->reg_lcd) {
+ ret = regulator_disable(fbi->reg_lcd);
+ if (ret)
+ dev_err(&fbi->pdev->dev,
+ "lcd regulator disable failed with error: %d\n",
+ ret);
+ return ret;
+ }
+
+ return 0;
}
static int imxfb_blank(int blank, struct fb_info *info)
@@ -626,13 +654,12 @@ static int imxfb_blank(int blank, struct fb_info *info)
case FB_BLANK_VSYNC_SUSPEND:
case FB_BLANK_HSYNC_SUSPEND:
case FB_BLANK_NORMAL:
- imxfb_disable_controller(fbi);
- break;
+ return imxfb_disable_controller(fbi);
case FB_BLANK_UNBLANK:
- imxfb_enable_controller(fbi);
- break;
+ return imxfb_enable_controller(fbi);
}
+
return 0;
}
@@ -734,8 +761,7 @@ static int imxfb_suspend(struct platform_device *dev, pm_message_t state)
pr_debug("%s\n", __func__);
- imxfb_disable_controller(fbi);
- return 0;
+ return imxfb_disable_controller(fbi);
}
static int imxfb_resume(struct platform_device *dev)
@@ -745,8 +771,7 @@ static int imxfb_resume(struct platform_device *dev)
pr_debug("%s\n", __func__);
- imxfb_enable_controller(fbi);
- return 0;
+ return imxfb_enable_controller(fbi);
}
#else
#define imxfb_suspend NULL
@@ -1020,6 +1045,12 @@ static int imxfb_probe(struct platform_device *pdev)
goto failed_register;
}
+ fbi->reg_lcd = devm_regulator_get(&pdev->dev, "lcd");
+ if (IS_ERR(fbi->reg_lcd)) {
+ dev_info(&pdev->dev, "No lcd regulator used.\n");
+ fbi->reg_lcd = NULL;
+ }
+
imxfb_enable_controller(fbi);
fbi->pdev = pdev;
#ifdef PWMR_BACKLIGHT_AVAILABLE
--
1.7.9.5
^ permalink raw reply related
* [RESEND PATCH 1/2] fb: reorder the lock sequence to fix potential dead lock
From: Gu Zheng @ 2013-11-05 10:00 UTC (permalink / raw)
To: Jean-Christophe PLAGNIOL-VILLARD, Tomi Valkeinen
Cc: Linux Fbdev development list, linux-kernel
Following commits:
50e244cc79 fb: rework locking to fix lock ordering on takeover
e93a9a8687 fb: Yet another band-aid for fixing lockdep mess
054430e773 fbcon: fix locking harder
reworked locking to fix related lock ordering on takeover, and introduced console_lock
into fbmem, but it seems that the new lock sequence(fb_info->lock ---> console_lock)
is against with the one in console_callback(console_lock ---> fb_info->lock), and leads to
a potential dead lock as following:
[ 601.079000] ===========================
[ 601.079000] [ INFO: possible circular locking dependency detected ]
[ 601.079000] 3.11.0 #189 Not tainted
[ 601.079000] -------------------------------------------------------
[ 601.079000] kworker/0:3/619 is trying to acquire lock:
[ 601.079000] (&fb_info->lock){+.+.+.}, at: [<ffffffff81397566>] lock_fb_info+0x26/0x60
[ 601.079000]
but task is already holding lock:
[ 601.079000] (console_lock){+.+.+.}, at: [<ffffffff8141aae3>] console_callback+0x13/0x160
[ 601.079000]
which lock already depends on the new lock.
[ 601.079000]
the existing dependency chain (in reverse order) is:
[ 601.079000]
-> #1 (console_lock){+.+.+.}:
[ 601.079000] [<ffffffff810dc971>] lock_acquire+0xa1/0x140
[ 601.079000] [<ffffffff810c6267>] console_lock+0x77/0x80
[ 601.079000] [<ffffffff81399448>] register_framebuffer+0x1d8/0x320
[ 601.079000] [<ffffffff81cfb4c8>] efifb_probe+0x408/0x48f
[ 601.079000] [<ffffffff8144a963>] platform_drv_probe+0x43/0x80
[ 601.079000] [<ffffffff8144853b>] driver_probe_device+0x8b/0x390
[ 601.079000] [<ffffffff814488eb>] __driver_attach+0xab/0xb0
[ 601.079000] [<ffffffff814463bd>] bus_for_each_dev+0x5d/0xa0
[ 601.079000] [<ffffffff81447e6e>] driver_attach+0x1e/0x20
[ 601.079000] [<ffffffff81447a07>] bus_add_driver+0x117/0x290
[ 601.079000] [<ffffffff81448fea>] driver_register+0x7a/0x170
[ 601.079000] [<ffffffff8144a10a>] __platform_driver_register+0x4a/0x50
[ 601.079000] [<ffffffff8144a12d>] platform_driver_probe+0x1d/0xb0
[ 601.079000] [<ffffffff81cfb0a1>] efifb_init+0x273/0x292
[ 601.079000] [<ffffffff81002132>] do_one_initcall+0x102/0x1c0
[ 601.079000] [<ffffffff81cb80a6>] kernel_init_freeable+0x15d/0x1ef
[ 601.079000] [<ffffffff8166d2de>] kernel_init+0xe/0xf0
[ 601.079000] [<ffffffff816914ec>] ret_from_fork+0x7c/0xb0
[ 601.079000]
-> #0 (&fb_info->lock){+.+.+.}:
[ 601.079000] [<ffffffff810dc1d8>] __lock_acquire+0x1e18/0x1f10
[ 601.079000] [<ffffffff810dc971>] lock_acquire+0xa1/0x140
[ 601.079000] [<ffffffff816835ca>] mutex_lock_nested+0x7a/0x3b0
[ 601.079000] [<ffffffff81397566>] lock_fb_info+0x26/0x60
[ 601.079000] [<ffffffff813a4aeb>] fbcon_blank+0x29b/0x2e0
[ 601.079000] [<ffffffff81418658>] do_blank_screen+0x1d8/0x280
[ 601.079000] [<ffffffff8141ab34>] console_callback+0x64/0x160
[ 601.079000] [<ffffffff8108d855>] process_one_work+0x1f5/0x540
[ 601.079000] [<ffffffff8108e04c>] worker_thread+0x11c/0x370
[ 601.079000] [<ffffffff81095fbd>] kthread+0xed/0x100
[ 601.079000] [<ffffffff816914ec>] ret_from_fork+0x7c/0xb0
[ 601.079000]
other info that might help us debug this:
[ 601.079000] Possible unsafe locking scenario:
[ 601.079000] CPU0 CPU1
[ 601.079000] ---- ----
[ 601.079000] lock(console_lock);
[ 601.079000] lock(&fb_info->lock);
[ 601.079000] lock(console_lock);
[ 601.079000] lock(&fb_info->lock);
[ 601.079000]
*** DEADLOCK ***
so we reorder the lock sequence the same as it in console_callback() to
avoid this issue. And following Tomi's suggestion, fix these similar
issues all in fb subsystem.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
---
drivers/video/fbmem.c | 50 ++++++++++++++++++++++++-------------
drivers/video/fbsysfs.c | 19 ++++++++++----
drivers/video/sh_mobile_lcdcfb.c | 10 ++++---
3 files changed, 51 insertions(+), 28 deletions(-)
diff --git a/drivers/video/fbmem.c b/drivers/video/fbmem.c
index dacaf74..010d191 100644
--- a/drivers/video/fbmem.c
+++ b/drivers/video/fbmem.c
@@ -1108,14 +1108,16 @@ static long do_fb_ioctl(struct fb_info *info, unsigned int cmd,
case FBIOPUT_VSCREENINFO:
if (copy_from_user(&var, argp, sizeof(var)))
return -EFAULT;
- if (!lock_fb_info(info))
- return -ENODEV;
console_lock();
+ if (!lock_fb_info(info)) {
+ console_unlock();
+ return -ENODEV;
+ }
info->flags |= FBINFO_MISC_USEREVENT;
ret = fb_set_var(info, &var);
info->flags &= ~FBINFO_MISC_USEREVENT;
- console_unlock();
unlock_fb_info(info);
+ console_unlock();
if (!ret && copy_to_user(argp, &var, sizeof(var)))
ret = -EFAULT;
break;
@@ -1144,12 +1146,14 @@ static long do_fb_ioctl(struct fb_info *info, unsigned int cmd,
case FBIOPAN_DISPLAY:
if (copy_from_user(&var, argp, sizeof(var)))
return -EFAULT;
- if (!lock_fb_info(info))
- return -ENODEV;
console_lock();
+ if (!lock_fb_info(info)) {
+ console_unlock();
+ return -ENODEV;
+ }
ret = fb_pan_display(info, &var);
- console_unlock();
unlock_fb_info(info);
+ console_unlock();
if (ret = 0 && copy_to_user(argp, &var, sizeof(var)))
return -EFAULT;
break;
@@ -1184,23 +1188,27 @@ static long do_fb_ioctl(struct fb_info *info, unsigned int cmd,
break;
}
event.data = &con2fb;
- if (!lock_fb_info(info))
- return -ENODEV;
console_lock();
+ if (!lock_fb_info(info)) {
+ console_unlock();
+ return -ENODEV;
+ }
event.info = info;
ret = fb_notifier_call_chain(FB_EVENT_SET_CONSOLE_MAP, &event);
- console_unlock();
unlock_fb_info(info);
+ console_unlock();
break;
case FBIOBLANK:
- if (!lock_fb_info(info))
- return -ENODEV;
console_lock();
+ if (!lock_fb_info(info)) {
+ console_unlock();
+ return -ENODEV;
+ }
info->flags |= FBINFO_MISC_USEREVENT;
ret = fb_blank(info, arg);
info->flags &= ~FBINFO_MISC_USEREVENT;
- console_unlock();
unlock_fb_info(info);
+ console_unlock();
break;
default:
if (!lock_fb_info(info))
@@ -1660,12 +1668,15 @@ static int do_register_framebuffer(struct fb_info *fb_info)
registered_fb[i] = fb_info;
event.info = fb_info;
- if (!lock_fb_info(fb_info))
- return -ENODEV;
console_lock();
+ if (!lock_fb_info(fb_info)) {
+ console_unlock();
+ return -ENODEV;
+ }
+
fb_notifier_call_chain(FB_EVENT_FB_REGISTERED, &event);
- console_unlock();
unlock_fb_info(fb_info);
+ console_unlock();
return 0;
}
@@ -1678,13 +1689,16 @@ static int do_unregister_framebuffer(struct fb_info *fb_info)
if (i < 0 || i >= FB_MAX || registered_fb[i] != fb_info)
return -EINVAL;
- if (!lock_fb_info(fb_info))
- return -ENODEV;
console_lock();
+ if (!lock_fb_info(fb_info)) {
+ console_unlock();
+ return -ENODEV;
+ }
+
event.info = fb_info;
ret = fb_notifier_call_chain(FB_EVENT_FB_UNBIND, &event);
- console_unlock();
unlock_fb_info(fb_info);
+ console_unlock();
if (ret)
return -EINVAL;
diff --git a/drivers/video/fbsysfs.c b/drivers/video/fbsysfs.c
index ef476b0..53444ac 100644
--- a/drivers/video/fbsysfs.c
+++ b/drivers/video/fbsysfs.c
@@ -177,9 +177,12 @@ static ssize_t store_modes(struct device *device,
if (i * sizeof(struct fb_videomode) != count)
return -EINVAL;
- if (!lock_fb_info(fb_info))
- return -ENODEV;
console_lock();
+ if (!lock_fb_info(fb_info)) {
+ console_unlock();
+ return -ENODEV;
+ }
+
list_splice(&fb_info->modelist, &old_list);
fb_videomode_to_modelist((const struct fb_videomode *)buf, i,
&fb_info->modelist);
@@ -189,8 +192,8 @@ static ssize_t store_modes(struct device *device,
} else
fb_destroy_modelist(&old_list);
- console_unlock();
unlock_fb_info(fb_info);
+ console_unlock();
return 0;
}
@@ -404,12 +407,16 @@ static ssize_t store_fbstate(struct device *device,
state = simple_strtoul(buf, &last, 0);
- if (!lock_fb_info(fb_info))
- return -ENODEV;
console_lock();
+ if (!lock_fb_info(fb_info)) {
+ console_unlock();
+ return -ENODEV;
+ }
+
fb_set_suspend(fb_info, (int)state);
- console_unlock();
+
unlock_fb_info(fb_info);
+ console_unlock();
return count;
}
diff --git a/drivers/video/sh_mobile_lcdcfb.c b/drivers/video/sh_mobile_lcdcfb.c
index 0264704..45d0312 100644
--- a/drivers/video/sh_mobile_lcdcfb.c
+++ b/drivers/video/sh_mobile_lcdcfb.c
@@ -574,8 +574,9 @@ static int sh_mobile_lcdc_display_notify(struct sh_mobile_lcdc_chan *ch,
switch (event) {
case SH_MOBILE_LCDC_EVENT_DISPLAY_CONNECT:
/* HDMI plug in */
+ console_lock();
if (lock_fb_info(info)) {
- console_lock();
+
ch->display.width = monspec->max_x * 10;
ch->display.height = monspec->max_y * 10;
@@ -594,19 +595,20 @@ static int sh_mobile_lcdc_display_notify(struct sh_mobile_lcdc_chan *ch,
fb_set_suspend(info, 0);
}
- console_unlock();
+
unlock_fb_info(info);
}
+ console_unlock();
break;
case SH_MOBILE_LCDC_EVENT_DISPLAY_DISCONNECT:
/* HDMI disconnect */
+ console_lock();
if (lock_fb_info(info)) {
- console_lock();
fb_set_suspend(info, 1);
- console_unlock();
unlock_fb_info(info);
}
+ console_unlock();
break;
case SH_MOBILE_LCDC_EVENT_DISPLAY_MODE:
--
1.7.7
^ permalink raw reply related
* Re: [PATCH 0/3] omapdss: venc: Add support for bypass and acbias.
From: Belisko Marek @ 2013-11-05 7:24 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1381784555-18344-1-git-send-email-marek@goldelico.com>
Hi,
ping.
On Mon, Oct 14, 2013 at 11:02 PM, Marek Belisko <marek@goldelico.com> wrote:
> This patches is adding bypass and acbias functionality to omapdss venc driver.
> In first patch we export updatin bypass and acbias in devconf1 register. Next patch
> add handling for updating in venc driver and last patch add driver for opa362 which
> is used on gta04 board and set bypass + acbias.
Is there a chance to get this series to 3.13? Thanks.
>
> Marek Belisko (3):
> arm: omap2: Export devconf1 bypass and acbias.
> video: venc: Add new callback and handling for bypass and acbias
> setup.
> omapdss: Add OPA362 analog video amplifier driver.
>
> arch/arm/mach-omap2/Makefile | 2 +
> arch/arm/mach-omap2/control.h | 2 +
> arch/arm/mach-omap2/omap3-tvout.c | 36 +++
> drivers/video/omap2/displays-new/Kconfig | 6 +
> drivers/video/omap2/displays-new/Makefile | 1 +
> .../video/omap2/displays-new/amplifier-opa362.c | 294 +++++++++++++++++++++
> drivers/video/omap2/dss/venc.c | 21 ++
> include/linux/omap-tvout.h | 14 +
> include/video/omap-panel-data.h | 17 ++
> include/video/omapdss.h | 2 +
> 10 files changed, 395 insertions(+)
> create mode 100644 arch/arm/mach-omap2/omap3-tvout.c
> create mode 100644 drivers/video/omap2/displays-new/amplifier-opa362.c
> create mode 100644 include/linux/omap-tvout.h
>
> --
> 1.8.1.2
>
Marek
--
as simple and primitive as possible
-------------------------------------------------
Marek Belisko - OPEN-NANDRA
Freelance Developer
Ruska Nova Ves 219 | Presov, 08005 Slovak Republic
Tel: +421 915 052 184
skype: marekwhite
twitter: #opennandra
web: http://open-nandra.com
^ permalink raw reply
* Re: [PATCHv4][ 2/6] dma: ipu: Add devicetree support.
From: Sascha Hauer @ 2013-11-05 6:09 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1383581724-14817-2-git-send-email-denis@eukrea.com>
On Mon, Nov 04, 2013 at 05:15:20PM +0100, Denis Carikli wrote:
> diff --git a/Documentation/devicetree/bindings/dma/fsl-imx-ipu.txt b/Documentation/devicetree/bindings/dma/fsl-imx-ipu.txt
> new file mode 100644
> index 0000000..2f3c976
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/dma/fsl-imx-ipu.txt
> @@ -0,0 +1,20 @@
> +* Freescale Image Processing Unit (IPU) support for i.MX3x.
> +
> +This driver supports the imx31 and imx35 devices.
> +
> +Required properties:
> +- compatible : Should be "fsl,imx31-ipu".
> +- reg : Should contain IPU registers location and length.
> +- interrupts : First item should be IPU interrupt, second one is optional and
> + should contain IPU Error interrupt.
> +
> +Example:
> +
> + ipu: ipu@53fc0000 {
> + compatible = "fsl,imx31-ipu";
> + reg = < 0x53fc0000 0x5f
> + 0x53fc0088 0x2b >;
> + interrupts = <42 41>;
> + clocks = <&clks 55>;
> + clock-names = "";
> + };
As said before: I don't think that splitting the IPU in several nodes
like above just to satisfy the current Linux driver setup is
appropriate.
The IPU should rather look like:
ipu: ipu@53fc0000 {
compatible = "fsl,imx31-ipu";
reg = <0x53fc0000 0x4000>;
interrupts = <42 31>;
clocks = <&clks 55 ...>;
clock-names = "...";
};
Note that the above covers the whole address space of the IPU. This is
more close to the IPUv3 binding. With separating the IDMAC and DI nodes
you force us to keep the current driver separation between dma and fb
driver. The IPU should never have used the Linux DMA driver framework
though.
When you cover the whole address space you could then in the
corresponding driver register platform devices which match to the
current dma/fb driver combination.
Sascha
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox