* [PATCHv3 35/41] Doc/DT: Add DT binding documentation for DVI Connector
From: Tomi Valkeinen @ 2014-01-21 10:57 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT binding documentation for DVI Connector.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
.../devicetree/bindings/video/dvi-connector.txt | 26 ++++++++++++++++++++++
1 file changed, 26 insertions(+)
create mode 100644 Documentation/devicetree/bindings/video/dvi-connector.txt
diff --git a/Documentation/devicetree/bindings/video/dvi-connector.txt b/Documentation/devicetree/bindings/video/dvi-connector.txt
new file mode 100644
index 000000000000..6a0aff866c78
--- /dev/null
+++ b/Documentation/devicetree/bindings/video/dvi-connector.txt
@@ -0,0 +1,26 @@
+DVI Connector
+=======
+
+Required properties:
+- compatible: "dvi-connector"
+
+Optional properties:
+- label: a symbolic name for the connector
+- i2c-bus: phandle to the i2c bus that is connected to DVI DDC
+
+Required nodes:
+- Video port for DVI input
+
+Example
+-------
+
+dvi0: connector@0 {
+ compatible = "dvi-connector";
+ label = "dvi";
+
+ i2c-bus = <&i2c3>;
+
+ dvi_connector_in: endpoint {
+ remote-endpoint = <&tfp410_out>;
+ };
+};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 34/41] Doc/DT: Add DT binding documentation for Analog TV Connector
From: Tomi Valkeinen @ 2014-01-21 10:57 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT binding documentation for Analog TV Connector.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
.../bindings/video/analog-tv-connector.txt | 23 ++++++++++++++++++++++
1 file changed, 23 insertions(+)
create mode 100644 Documentation/devicetree/bindings/video/analog-tv-connector.txt
diff --git a/Documentation/devicetree/bindings/video/analog-tv-connector.txt b/Documentation/devicetree/bindings/video/analog-tv-connector.txt
new file mode 100644
index 000000000000..d6be373d8705
--- /dev/null
+++ b/Documentation/devicetree/bindings/video/analog-tv-connector.txt
@@ -0,0 +1,23 @@
+Analog TV Connector
+=========+
+Required properties:
+- compatible: "composite-connector" or "svideo-connector"
+
+Optional properties:
+- label: a symbolic name for the connector
+
+Required nodes:
+- Video port for TV input
+
+Example
+-------
+
+tv: connector {
+ compatible = "composite-connector";
+ label = "tv";
+
+ tv_connector_in: endpoint {
+ remote-endpoint = <&venc_out>;
+ };
+};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 33/41] Doc/DT: Add OMAP DSS DT Bindings
From: Tomi Valkeinen @ 2014-01-21 10:57 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add device tree bindings for OMAP Display Subsystem for the following
SoCs: OMAP2, OMAP3, OMAP4.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
.../devicetree/bindings/video/ti,omap-dss.txt | 197 +++++++++++++++++++++
.../devicetree/bindings/video/ti,omap2-dss.txt | 54 ++++++
.../devicetree/bindings/video/ti,omap3-dss.txt | 73 ++++++++
.../devicetree/bindings/video/ti,omap4-dss.txt | 99 +++++++++++
.../devicetree/bindings/video/video-ports.txt | 22 +++
5 files changed, 445 insertions(+)
create mode 100644 Documentation/devicetree/bindings/video/ti,omap-dss.txt
create mode 100644 Documentation/devicetree/bindings/video/ti,omap2-dss.txt
create mode 100644 Documentation/devicetree/bindings/video/ti,omap3-dss.txt
create mode 100644 Documentation/devicetree/bindings/video/ti,omap4-dss.txt
create mode 100644 Documentation/devicetree/bindings/video/video-ports.txt
diff --git a/Documentation/devicetree/bindings/video/ti,omap-dss.txt b/Documentation/devicetree/bindings/video/ti,omap-dss.txt
new file mode 100644
index 000000000000..3b3a7c09106c
--- /dev/null
+++ b/Documentation/devicetree/bindings/video/ti,omap-dss.txt
@@ -0,0 +1,197 @@
+Texas Instruments OMAP Display Subsystem
+====================
+
+Generic Description
+-------------------
+
+This document is a generic description of the OMAP Display Subsystem bindings.
+Binding details for each OMAP SoC version are described in respective binding
+documentation.
+
+The OMAP Display Subsystem (DSS) hardware consists of DSS Core, DISPC module and
+a number of encoder modules. All DSS versions contain DSS Core and DISPC, but
+the encoder modules vary.
+
+The DSS Core is the parent of the other DSS modules, and manages clock routing,
+integration to the SoC, etc.
+
+DISPC is the display controller, which reads pixels from the memory and outputs
+a RGB pixel stream to encoders.
+
+The encoder modules encode the received RGB pixel stream to a video output like
+HDMI, MIPI DPI, etc.
+
+Video Ports
+-----------
+
+The DSS Core and the encoders have video port outputs. The structure of the
+video ports is described in Documentation/devicetree/bindings/video/video-
+ports.txt, and the properties for the ports and endpoints for each encoder are
+described in the SoC's DSS binding documentation.
+
+The video ports are used to describe the connections to external hardware, like
+panels or external encoders.
+
+Aliases
+-------
+
+The board dts file may define aliases for displays to assign "displayX" style
+name for each display. If no aliases are defined, a semi-random number is used
+for the display.
+
+Example
+-------
+
+A shortened example of the DSS description for OMAP4, with non-relevant parts
+removed, defined in omap4.dtsi:
+
+dss: dss@58000000 {
+ compatible = "ti,omap4-dss", "simple-bus";
+ reg = <0x58000000 0x80>;
+ status = "disabled";
+ ti,hwmods = "dss_core";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ dispc@58001000 {
+ compatible = "ti,omap4-dispc";
+ reg = <0x58001000 0x1000>;
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "dss_dispc";
+ };
+
+ hdmi: encoder@58006000 {
+ compatible = "ti,omap4-hdmi";
+ reg = <0x58006000 0x200>,
+ <0x58006200 0x100>,
+ <0x58006300 0x100>,
+ <0x58006400 0x1000>;
+ reg-names = "wp", "pll", "phy", "core";
+ interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ ti,hwmods = "dss_hdmi";
+ };
+};
+
+A shortened example of the board description for OMAP4 Panda board, defined in
+omap4-panda.dts.
+
+The Panda board has a DVI and a HDMI connector, and the board contains a TFP410
+chip (MIPI DPI to DVI encoder) and a TPD12S015 chip (HDMI ESD protection & level
+shifter). The video pipelines for the connectors are formed as follows:
+
+DSS Core --(MIPI DPI)--> TFP410 --(DVI)--> DVI Connector
+OMAP HDMI --(HDMI)--> TPD12S015 --(HDMI)--> HDMI COnnector
+
+/ {
+ aliases {
+ display0 = &dvi0;
+ display1 = &hdmi0;
+ };
+
+ tfp410: encoder@0 {
+ compatible = "ti,tfp410";
+ gpios = <&gpio1 0 GPIO_ACTIVE_LOW>; /* 0, power-down */
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&tfp410_pins>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ tfp410_in: endpoint@0 {
+ remote-endpoint = <&dpi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ tfp410_out: endpoint@0 {
+ remote-endpoint = <&dvi_connector_in>;
+ };
+ };
+ };
+ };
+
+ dvi0: connector@0 {
+ compatible = "dvi-connector";
+ label = "dvi";
+
+ i2c-bus = <&i2c3>;
+
+ dvi_connector_in: endpoint {
+ remote-endpoint = <&tfp410_out>;
+ };
+ };
+
+ tpd12s015: encoder@1 {
+ compatible = "ti,tpd12s015";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&tpd12s015_pins>;
+
+ gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>, /* 60, CT CP HPD */
+ <&gpio2 9 GPIO_ACTIVE_HIGH>, /* 41, LS OE */
+ <&gpio2 31 GPIO_ACTIVE_HIGH>; /* 63, HPD */
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ tpd12s015_in: endpoint@0 {
+ remote-endpoint = <&hdmi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ tpd12s015_out: endpoint@0 {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+ };
+ };
+ };
+
+ hdmi0: connector@1 {
+ compatible = "hdmi-connector";
+ label = "hdmi";
+
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&tpd12s015_out>;
+ };
+ };
+};
+
+&dss {
+ status = "ok";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&dss_dpi_pins>;
+
+ dpi_out: endpoint {
+ remote-endpoint = <&tfp410_in>;
+ data-lines = <24>;
+ };
+};
+
+&hdmi {
+ status = "ok";
+ vdda-supply = <&vdac>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&dss_hdmi_pins>;
+
+ hdmi_out: endpoint {
+ remote-endpoint = <&tpd12s015_in>;
+ };
+};
diff --git a/Documentation/devicetree/bindings/video/ti,omap2-dss.txt b/Documentation/devicetree/bindings/video/ti,omap2-dss.txt
new file mode 100644
index 000000000000..fa8bb2ed1170
--- /dev/null
+++ b/Documentation/devicetree/bindings/video/ti,omap2-dss.txt
@@ -0,0 +1,54 @@
+Texas Instruments OMAP2 Display Subsystem
+====================+
+See Documentation/devicetree/bindings/video/ti,omap-dss.txt for generic
+description about OMAP Display Subsystem bindings.
+
+DSS Core
+--------
+
+Required properties:
+- compatible: "ti,omap2-dss"
+- reg: address and length of the register space
+- ti,hwmods: "dss_core"
+
+Optional nodes:
+- Video port for DPI output
+
+DPI Endpoint required properties:
+- data-lines: number of lines used
+
+
+DISPC
+-----
+
+Required properties:
+- compatible: "ti,omap2-dispc"
+- reg: address and length of the register space
+- ti,hwmods: "dss_dispc"
+- interrupts: the DISPC interrupt
+
+
+RFBI
+----
+
+Required properties:
+- compatible: "ti,omap2-rfbi"
+- reg: address and length of the register space
+- ti,hwmods: "dss_rfbi"
+
+
+VENC
+----
+
+Required properties:
+- compatible: "ti,omap2-venc"
+- reg: address and length of the register space
+- ti,hwmods: "dss_venc"
+- vdda-supply: power supply for DAC
+
+VENC Endpoint required properties:
+
+Required properties:
+- ti,invert-polarity: invert the polarity of the video signal
+- ti,channels: 1 for composite, 2 for s-video
diff --git a/Documentation/devicetree/bindings/video/ti,omap3-dss.txt b/Documentation/devicetree/bindings/video/ti,omap3-dss.txt
new file mode 100644
index 000000000000..2b62c78c9596
--- /dev/null
+++ b/Documentation/devicetree/bindings/video/ti,omap3-dss.txt
@@ -0,0 +1,73 @@
+Texas Instruments OMAP3 Display Subsystem
+====================+
+See Documentation/devicetree/bindings/video/ti,omap-dss.txt for generic
+description about OMAP Display Subsystem bindings.
+
+DSS Core
+--------
+
+Required properties:
+- compatible: "ti,omap3-dss"
+- reg: address and length of the register space
+- ti,hwmods: "dss_core"
+
+Optional nodes:
+- Video ports:
+ - Port 0: DPI output
+ - Port 1: SDI output
+
+DPI Endpoint required properties:
+- data-lines: number of lines used
+
+SDI Endpoint required properties:
+- datapairs: number of datapairs used
+
+
+DISPC
+-----
+
+Required properties:
+- compatible: "ti,omap3-dispc"
+- reg: address and length of the register space
+- ti,hwmods: "dss_dispc"
+- interrupts: the DISPC interrupt
+
+
+RFBI
+----
+
+Required properties:
+- compatible: "ti,omap3-rfbi"
+- reg: address and length of the register space
+- ti,hwmods: "dss_rfbi"
+
+
+VENC
+----
+
+Required properties:
+- compatible: "ti,omap3-venc"
+- reg: address and length of the register space
+- ti,hwmods: "dss_venc"
+- vdda-supply: power supply for DAC
+
+VENC Endpoint required properties:
+- ti,invert-polarity: invert the polarity of the video signal
+- ti,channels: 1 for composite, 2 for s-video
+
+
+DSI
+---
+
+Required properties:
+- compatible: "ti,omap3-dsi"
+- reg: addresses and lengths of the register spaces for 'proto', 'phy' and 'pll'
+- reg-names: "proto", "phy", "pll"
+- interrupts: the DSI interrupt line
+- ti,hwmods: "dss_dsi1"
+- vdd-supply: power supply for DSI
+
+DSI Endpoint required properties:
+- lanes: list of pin numbers for the DSI lanes: CLK+, CLK-, DATA0+, DATA0-,
+ DATA1+, DATA1-, ...
diff --git a/Documentation/devicetree/bindings/video/ti,omap4-dss.txt b/Documentation/devicetree/bindings/video/ti,omap4-dss.txt
new file mode 100644
index 000000000000..37aa9e6a173e
--- /dev/null
+++ b/Documentation/devicetree/bindings/video/ti,omap4-dss.txt
@@ -0,0 +1,99 @@
+Texas Instruments OMAP4 Display Subsystem
+====================+
+See Documentation/devicetree/bindings/video/ti,omap-dss.txt for generic
+description about OMAP Display Subsystem bindings.
+
+DSS Core
+--------
+
+Required properties:
+- compatible: "ti,omap4-dss"
+- reg: address and length of the register space
+- ti,hwmods: "dss_core"
+
+Required nodes:
+- DISPC
+
+Optional nodes:
+- DSS Submodules: RFBI, VENC, DSI, HDMI
+- Video port for DPI output
+
+DPI Endpoint required properties:
+- data-lines: number of lines used
+
+
+DISPC
+-----
+
+Required properties:
+- compatible: "ti,omap4-dispc"
+- reg: address and length of the register space
+- ti,hwmods: "dss_dispc"
+- interrupts: the DISPC interrupt
+
+
+RFBI
+----
+
+Required properties:
+- compatible: "ti,omap4-rfbi"
+- reg: address and length of the register space
+- ti,hwmods: "dss_rfbi"
+
+Optional nodes:
+- Video port for RFBI output
+- RFBI controlled peripherals
+
+
+VENC
+----
+
+Required properties:
+- compatible: "ti,omap4-venc"
+- reg: address and length of the register space
+- ti,hwmods: "dss_venc"
+- vdda-supply: power supply for DAC
+
+Optional nodes:
+- Video port for VENC output
+
+VENC Endpoint required properties:
+- ti,invert-polarity: invert the polarity of the video signal
+- ti,channels: 1 for composite, 2 for s-video
+
+
+DSI
+---
+
+Required properties:
+- compatible: "ti,omap4-dsi"
+- reg: addresses and lengths of the register spaces for 'proto', 'phy' and 'pll'
+- reg-names: "proto", "phy", "pll"
+- interrupts: the DSI interrupt line
+- ti,hwmods: "dss_dsi1" or "dss_dsi2"
+- vdd-supply: power supply for DSI
+
+Optional nodes:
+- Video port for DSI output
+- DSI controlled peripherals
+
+DSI Endpoint required properties:
+- lanes: list of pin numbers for the DSI lanes: CLK+, CLK-, DATA0+, DATA0-,
+ DATA1+, DATA1-, ...
+
+
+HDMI
+----
+
+Required properties:
+- compatible: "ti,omap4-hdmi"
+- reg: addresses and lengths of the register spaces for 'wp', 'pll', 'phy',
+ 'core'
+- reg-names: "wp", "pll", "phy", "core"
+- interrupts: the HDMI interrupt line
+- ti,hwmods: "dss_hdmi"
+- vdda-supply: vdda power supply
+
+Optional nodes:
+- Video port for HDMI output
diff --git a/Documentation/devicetree/bindings/video/video-ports.txt b/Documentation/devicetree/bindings/video/video-ports.txt
new file mode 100644
index 000000000000..dad4c436caae
--- /dev/null
+++ b/Documentation/devicetree/bindings/video/video-ports.txt
@@ -0,0 +1,22 @@
+Video Ports
+=====+
+The video port bindings used for display devices is a superset of the v4l2 video
+ports described here:
+
+Documentation/devicetree/bindings/media/video-interfaces.txt
+
+The only difference is a more compact way to describe devices with only one
+endpoint. In cases like that, the 'ports' and 'port' nodes are not needed. For
+example, a DPI panel with a single input endpoint:
+
+lcd0: display@0 {
+ compatible = "samsung,lte430wq-f0c", "panel-dpi";
+
+ lcd_in: endpoint {
+ remote-endpoint = <&dpi_out>;
+ };
+};
+
+The rest of the bindings are the same as in v4l2 video port bindings and not
+described here.
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 32/41] ARM: OMAP2+: remove pdata quirks for displays
From: Tomi Valkeinen @ 2014-01-21 10:57 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Remove pdata quirks for the displays on boards that are now supported
properly with DT.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
arch/arm/mach-omap2/dss-common.c | 224 -------------------------------------
arch/arm/mach-omap2/pdata-quirks.c | 3 -
2 files changed, 227 deletions(-)
diff --git a/arch/arm/mach-omap2/dss-common.c b/arch/arm/mach-omap2/dss-common.c
index dadccc91488c..010bb72d2b75 100644
--- a/arch/arm/mach-omap2/dss-common.c
+++ b/arch/arm/mach-omap2/dss-common.c
@@ -33,227 +33,3 @@
#include "soc.h"
#include "dss-common.h"
#include "mux.h"
-
-#define HDMI_GPIO_CT_CP_HPD 60 /* HPD mode enable/disable */
-#define HDMI_GPIO_LS_OE 41 /* Level shifter for HDMI */
-#define HDMI_GPIO_HPD 63 /* Hotplug detect */
-
-#define PANDA_DVI_TFP410_POWER_DOWN_GPIO 0
-
-/* DVI Connector */
-static struct connector_dvi_platform_data omap4_panda_dvi_connector_pdata = {
- .name = "dvi",
- .source = "tfp410.0",
- .i2c_bus_num = 2,
-};
-
-static struct platform_device omap4_panda_dvi_connector_device = {
- .name = "connector-dvi",
- .id = 0,
- .dev.platform_data = &omap4_panda_dvi_connector_pdata,
-};
-
-/* TFP410 DPI-to-DVI chip */
-static struct encoder_tfp410_platform_data omap4_panda_tfp410_pdata = {
- .name = "tfp410.0",
- .source = "dpi.0",
- .data_lines = 24,
- .power_down_gpio = PANDA_DVI_TFP410_POWER_DOWN_GPIO,
-};
-
-static struct platform_device omap4_panda_tfp410_device = {
- .name = "tfp410",
- .id = 0,
- .dev.platform_data = &omap4_panda_tfp410_pdata,
-};
-
-/* HDMI Connector */
-static struct connector_hdmi_platform_data omap4_panda_hdmi_connector_pdata = {
- .name = "hdmi",
- .source = "tpd12s015.0",
-};
-
-static struct platform_device omap4_panda_hdmi_connector_device = {
- .name = "connector-hdmi",
- .id = 0,
- .dev.platform_data = &omap4_panda_hdmi_connector_pdata,
-};
-
-/* TPD12S015 HDMI ESD protection & level shifter chip */
-static struct encoder_tpd12s015_platform_data omap4_panda_tpd_pdata = {
- .name = "tpd12s015.0",
- .source = "hdmi.0",
-
- .ct_cp_hpd_gpio = HDMI_GPIO_CT_CP_HPD,
- .ls_oe_gpio = HDMI_GPIO_LS_OE,
- .hpd_gpio = HDMI_GPIO_HPD,
-};
-
-static struct platform_device omap4_panda_tpd_device = {
- .name = "tpd12s015",
- .id = 0,
- .dev.platform_data = &omap4_panda_tpd_pdata,
-};
-
-static struct omap_dss_board_info omap4_panda_dss_data = {
- .default_display_name = "dvi",
-};
-
-void __init omap4_panda_display_init_of(void)
-{
- omap_display_init(&omap4_panda_dss_data);
-
- platform_device_register(&omap4_panda_tfp410_device);
- platform_device_register(&omap4_panda_dvi_connector_device);
-
- platform_device_register(&omap4_panda_tpd_device);
- platform_device_register(&omap4_panda_hdmi_connector_device);
-}
-
-
-/* OMAP4 Blaze display data */
-
-#define DISPLAY_SEL_GPIO 59 /* LCD2/PicoDLP switch */
-#define DLP_POWER_ON_GPIO 40
-
-static struct panel_dsicm_platform_data dsi1_panel = {
- .name = "lcd",
- .source = "dsi.0",
- .reset_gpio = 102,
- .use_ext_te = false,
- .ext_te_gpio = 101,
- .pin_config = {
- .num_pins = 6,
- .pins = { 0, 1, 2, 3, 4, 5 },
- },
-};
-
-static struct platform_device sdp4430_lcd_device = {
- .name = "panel-dsi-cm",
- .id = 0,
- .dev.platform_data = &dsi1_panel,
-};
-
-static struct panel_dsicm_platform_data dsi2_panel = {
- .name = "lcd2",
- .source = "dsi.1",
- .reset_gpio = 104,
- .use_ext_te = false,
- .ext_te_gpio = 103,
- .pin_config = {
- .num_pins = 6,
- .pins = { 0, 1, 2, 3, 4, 5 },
- },
-};
-
-static struct platform_device sdp4430_lcd2_device = {
- .name = "panel-dsi-cm",
- .id = 1,
- .dev.platform_data = &dsi2_panel,
-};
-
-/* HDMI Connector */
-static struct connector_hdmi_platform_data sdp4430_hdmi_connector_pdata = {
- .name = "hdmi",
- .source = "tpd12s015.0",
-};
-
-static struct platform_device sdp4430_hdmi_connector_device = {
- .name = "connector-hdmi",
- .id = 0,
- .dev.platform_data = &sdp4430_hdmi_connector_pdata,
-};
-
-/* TPD12S015 HDMI ESD protection & level shifter chip */
-static struct encoder_tpd12s015_platform_data sdp4430_tpd_pdata = {
- .name = "tpd12s015.0",
- .source = "hdmi.0",
-
- .ct_cp_hpd_gpio = HDMI_GPIO_CT_CP_HPD,
- .ls_oe_gpio = HDMI_GPIO_LS_OE,
- .hpd_gpio = HDMI_GPIO_HPD,
-};
-
-static struct platform_device sdp4430_tpd_device = {
- .name = "tpd12s015",
- .id = 0,
- .dev.platform_data = &sdp4430_tpd_pdata,
-};
-
-
-static struct omap_dss_board_info sdp4430_dss_data = {
- .default_display_name = "lcd",
-};
-
-/*
- * we select LCD2 by default (instead of Pico DLP) by setting DISPLAY_SEL_GPIO.
- * Setting DLP_POWER_ON gpio enables the VDLP_2V5 VDLP_1V8 and VDLP_1V0 rails
- * used by picodlp on the 4430sdp platform. Keep this gpio disabled as LCD2 is
- * selected by default
- */
-void __init omap_4430sdp_display_init_of(void)
-{
- int r;
-
- r = gpio_request_one(DISPLAY_SEL_GPIO, GPIOF_OUT_INIT_HIGH,
- "display_sel");
- if (r)
- pr_err("%s: Could not get display_sel GPIO\n", __func__);
-
- r = gpio_request_one(DLP_POWER_ON_GPIO, GPIOF_OUT_INIT_LOW,
- "DLP POWER ON");
- if (r)
- pr_err("%s: Could not get DLP POWER ON GPIO\n", __func__);
-
- omap_display_init(&sdp4430_dss_data);
-
- platform_device_register(&sdp4430_lcd_device);
- platform_device_register(&sdp4430_lcd2_device);
-
- platform_device_register(&sdp4430_tpd_device);
- platform_device_register(&sdp4430_hdmi_connector_device);
-}
-
-
-/* OMAP3 IGEPv2 data */
-
-#define IGEP2_DVI_TFP410_POWER_DOWN_GPIO 170
-
-/* DVI Connector */
-static struct connector_dvi_platform_data omap3_igep2_dvi_connector_pdata = {
- .name = "dvi",
- .source = "tfp410.0",
- .i2c_bus_num = 2,
-};
-
-static struct platform_device omap3_igep2_dvi_connector_device = {
- .name = "connector-dvi",
- .id = 0,
- .dev.platform_data = &omap3_igep2_dvi_connector_pdata,
-};
-
-/* TFP410 DPI-to-DVI chip */
-static struct encoder_tfp410_platform_data omap3_igep2_tfp410_pdata = {
- .name = "tfp410.0",
- .source = "dpi.0",
- .data_lines = 24,
- .power_down_gpio = IGEP2_DVI_TFP410_POWER_DOWN_GPIO,
-};
-
-static struct platform_device omap3_igep2_tfp410_device = {
- .name = "tfp410",
- .id = 0,
- .dev.platform_data = &omap3_igep2_tfp410_pdata,
-};
-
-static struct omap_dss_board_info igep2_dss_data = {
- .default_display_name = "dvi",
-};
-
-void __init omap3_igep2_display_init_of(void)
-{
- omap_display_init(&igep2_dss_data);
-
- platform_device_register(&omap3_igep2_tfp410_device);
- platform_device_register(&omap3_igep2_dvi_connector_device);
-}
diff --git a/arch/arm/mach-omap2/pdata-quirks.c b/arch/arm/mach-omap2/pdata-quirks.c
index 39f020c982e8..68e3bca42e60 100644
--- a/arch/arm/mach-omap2/pdata-quirks.c
+++ b/arch/arm/mach-omap2/pdata-quirks.c
@@ -80,7 +80,6 @@ static void __init hsmmc2_internal_input_clk(void)
static void __init omap3_igep0020_legacy_init(void)
{
- omap3_igep2_display_init_of();
}
static void __init omap3_evm_legacy_init(void)
@@ -97,14 +96,12 @@ static void __init omap3_zoom_legacy_init(void)
#ifdef CONFIG_ARCH_OMAP4
static void __init omap4_sdp_legacy_init(void)
{
- omap_4430sdp_display_init_of();
legacy_init_wl12xx(WL12XX_REFCLOCK_26,
WL12XX_TCXOCLOCK_26, 53);
}
static void __init omap4_panda_legacy_init(void)
{
- omap4_panda_display_init_of();
legacy_init_ehci_clk("auxclk3_ck");
legacy_init_wl12xx(WL12XX_REFCLOCK_38, 0, 53);
}
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 31/41] OMAPDSS: remove DT hacks for regulators
From: Tomi Valkeinen @ 2014-01-21 10:57 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
For booting Panda and 4430SDP with DT, while DSS did not support DT, we
had to had small hacks in the omapdss driver to get the regulators. With
DT now supported in DSS, we can remove those hacks.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
drivers/video/omap2/dss/dsi.c | 9 +--------
drivers/video/omap2/dss/hdmi4.c | 9 +--------
2 files changed, 2 insertions(+), 16 deletions(-)
diff --git a/drivers/video/omap2/dss/dsi.c b/drivers/video/omap2/dss/dsi.c
index 98bb2d68a462..f461fe015554 100644
--- a/drivers/video/omap2/dss/dsi.c
+++ b/drivers/video/omap2/dss/dsi.c
@@ -1162,16 +1162,9 @@ static int dsi_regulator_init(struct platform_device *dsidev)
vdds_dsi = devm_regulator_get(&dsi->pdev->dev, "vdd");
- if (IS_ERR(vdds_dsi))
- vdds_dsi = devm_regulator_get(&dsi->pdev->dev, "vdds_dsi");
-
- /* DT HACK: try VCXIO to make omapdss work for o4 sdp/panda */
- if (IS_ERR(vdds_dsi))
- vdds_dsi = devm_regulator_get(&dsi->pdev->dev, "VCXIO");
-
if (IS_ERR(vdds_dsi)) {
if (PTR_ERR(vdds_dsi) != -EPROBE_DEFER)
- DSSERR("can't get VDDS_DSI regulator\n");
+ DSSERR("can't get DSI VDD regulator\n");
return PTR_ERR(vdds_dsi);
}
diff --git a/drivers/video/omap2/dss/hdmi4.c b/drivers/video/omap2/dss/hdmi4.c
index 064bec4e08d4..17b24b26f6cd 100644
--- a/drivers/video/omap2/dss/hdmi4.c
+++ b/drivers/video/omap2/dss/hdmi4.c
@@ -90,16 +90,9 @@ static int hdmi_init_regulator(void)
reg = devm_regulator_get(&hdmi.pdev->dev, "vdda");
- if (IS_ERR(reg)
- reg = devm_regulator_get(&hdmi.pdev->dev, "vdda_hdmi_dac");
-
- /* DT HACK: try VDAC to make omapdss work for o4 sdp/panda */
- if (IS_ERR(reg))
- reg = devm_regulator_get(&hdmi.pdev->dev, "VDAC");
-
if (IS_ERR(reg)) {
if (PTR_ERR(reg) != -EPROBE_DEFER)
- DSSERR("can't get VDDA_HDMI_DAC regulator\n");
+ DSSERR("can't get VDDA regulator\n");
return PTR_ERR(reg);
}
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 30/41] ARM: omap3-n900.dts: add display information
From: Tomi Valkeinen @ 2014-01-21 10:57 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT data for OMAP3 N900 board. The board has the following displays:
lcd: LCD panel connected to OMAP's SDI output
tv: analog svideo
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
arch/arm/boot/dts/omap3-n900.dts | 70 +++++++++++++++++++++++++++++++++++++---
1 file changed, 66 insertions(+), 4 deletions(-)
diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts
index 6fc85f963530..c1bb04d55d4b 100644
--- a/arch/arm/boot/dts/omap3-n900.dts
+++ b/arch/arm/boot/dts/omap3-n900.dts
@@ -74,6 +74,14 @@
};
};
+ tv: connector {
+ compatible = "composite-connector";
+ label = "tv";
+
+ tv_connector_in: endpoint {
+ remote-endpoint = <&venc_out>;
+ };
+ };
};
&omap3_pmx_core {
@@ -140,11 +148,23 @@
>;
};
- display_pins: pinmux_display_pins {
+ acx565akm_pins: pinmux_acx565akm_pins {
pinctrl-single,pins = <
0x0d4 (PIN_OUTPUT | MUX_MODE4) /* RX51_LCD_RESET_GPIO */
>;
};
+
+ dss_sdi_pins: pinmux_dss_sdi_pins {
+ pinctrl-single,pins = <
+ 0x0c0 (PIN_OUTPUT | MUX_MODE1) /* dss_data10.sdi_dat1n */
+ 0x0c2 (PIN_OUTPUT | MUX_MODE1) /* dss_data11.sdi_dat1p */
+ 0x0c4 (PIN_OUTPUT | MUX_MODE1) /* dss_data12.sdi_dat2n */
+ 0x0c6 (PIN_OUTPUT | MUX_MODE1) /* dss_data13.sdi_dat2p */
+
+ 0x0d8 (PIN_OUTPUT | MUX_MODE1) /* dss_data22.sdi_clkp */
+ 0x0da (PIN_OUTPUT | MUX_MODE1) /* dss_data23.sdi_clkn */
+ >;
+ };
};
&i2c1 {
@@ -471,13 +491,21 @@
spi-max-frequency = <6000000>;
reg = <0>;
};
- mipid@2 {
- compatible = "acx565akm";
+
+ acx565akm@2 {
+ compatible = "sony,acx565akm";
spi-max-frequency = <6000000>;
reg = <2>;
pinctrl-names = "default";
- pinctrl-0 = <&display_pins>;
+ pinctrl-0 = <&acx565akm_pins>;
+
+ label = "lcd";
+ gpios = <&gpio3 26 GPIO_ACTIVE_HIGH>; /* 90 */
+
+ lcd_in: endpoint {
+ remote-endpoint = <&sdi_out>;
+ };
};
};
@@ -503,3 +531,37 @@
pinctrl-names = "default";
pinctrl-0 = <&uart3_pins>;
};
+
+&dss {
+ status = "ok";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&dss_sdi_pins>;
+
+ vdds_sdi-supply = <&vaux1>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@1 {
+ reg = <1>;
+
+ sdi_out: endpoint {
+ remote-endpoint = <&lcd_in>;
+ datapairs = <2>;
+ };
+ };
+ };
+};
+
+&venc {
+ status = "ok";
+
+ vdda-supply = <&vdac>;
+
+ venc_out: endpoint {
+ remote-endpoint = <&tv_connector_in>;
+ ti,channels = <1>;
+ };
+};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 29/41] ARM: omap3-igep0020.dts: add display information
From: Tomi Valkeinen @ 2014-01-21 10:57 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
From: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Add DT data for OMAP3 IGEPv2 board. The board has the following displays:
dvi: uses TFP410 encoder to convert DPI to DVI
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
arch/arm/boot/dts/omap3-igep0020.dts | 59 +++++++++++++++++++++++++++++++-----
1 file changed, 52 insertions(+), 7 deletions(-)
diff --git a/arch/arm/boot/dts/omap3-igep0020.dts b/arch/arm/boot/dts/omap3-igep0020.dts
index 1c7e74d2d2bc..bd8dcc9f7ab4 100644
--- a/arch/arm/boot/dts/omap3-igep0020.dts
+++ b/arch/arm/boot/dts/omap3-igep0020.dts
@@ -61,14 +61,52 @@
reset-gpios = <&gpio1 24 GPIO_ACTIVE_LOW>; /* gpio_24 */
vcc-supply = <&hsusb1_power>;
};
+
+ tfp410: encoder@0 {
+ compatible = "ti,tfp410";
+ gpios = <&gpio6 10 GPIO_ACTIVE_LOW>; /* 170, power-down */
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&tfp410_pins>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ tfp410_in: endpoint@0 {
+ remote-endpoint = <&dpi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ tfp410_out: endpoint@0 {
+ remote-endpoint = <&dvi_connector_in>;
+ };
+ };
+ };
+ };
+
+ dvi0: connector@0 {
+ compatible = "dvi-connector";
+ label = "dvi";
+
+ i2c-bus = <&i2c3>;
+
+ dvi_connector_in: endpoint {
+ remote-endpoint = <&tfp410_out>;
+ };
+ };
};
&omap3_pmx_core {
pinctrl-names = "default";
pinctrl-0 = <
&hsusbb1_pins
- &tfp410_pins
- &dss_pins
>;
hsusbb1_pins: pinmux_hsusbb1_pins {
@@ -88,13 +126,13 @@
>;
};
- tfp410_pins: tfp410_dvi_pins {
+ tfp410_pins: pinmux_tfp410_pins {
pinctrl-single,pins = <
0x196 (PIN_OUTPUT | MUX_MODE4) /* hdq_sio.gpio_170 */
>;
};
- dss_pins: pinmux_dss_dvi_pins {
+ dss_dpi_pins: pinmux_dss_dpi_pins {
pinctrl-single,pins = <
0x0a4 (PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */
0x0a6 (PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */
@@ -216,7 +254,14 @@
phys = <&hsusb1_phy>;
};
-&vpll2 {
- /* Needed for DSS */
- regulator-name = "vdds_dsi";
+&dss {
+ status = "ok";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&dss_dpi_pins>;
+
+ dpi_out: endpoint {
+ remote-endpoint = <&tfp410_in>;
+ data-lines = <24>;
+ };
};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 28/41] ARM: omap3-beagle-xm.dts: add display information
From: Tomi Valkeinen @ 2014-01-21 10:57 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT data for OMAP3 Beagle-xM board. The board has the following displays:
dvi: uses TFP410 encoder to convert DPI to DVI
tv: analog svideo
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
arch/arm/boot/dts/omap3-beagle-xm.dts | 119 ++++++++++++++++++++++++++++++++++
1 file changed, 119 insertions(+)
diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts
index df33a50bc070..f6cec7e6ac11 100644
--- a/arch/arm/boot/dts/omap3-beagle-xm.dts
+++ b/arch/arm/boot/dts/omap3-beagle-xm.dts
@@ -24,6 +24,11 @@
reg = <0x80000000 0x20000000>; /* 512 MB */
};
+ aliases {
+ display0 = &dvi0;
+ display1 = &tv0;
+ };
+
leds {
compatible = "gpio-leds";
@@ -86,6 +91,54 @@
reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>; /* gpio_147 */
vcc-supply = <&hsusb2_power>;
};
+
+ tfp410: encoder@0 {
+ compatible = "ti,tfp410";
+ gpios = <&twl_gpio 2 GPIO_ACTIVE_LOW>;
+
+ /* XXX pinctrl from twl */
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ tfp410_in: endpoint@0 {
+ remote-endpoint = <&dpi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ tfp410_out: endpoint@0 {
+ remote-endpoint = <&dvi_connector_in>;
+ };
+ };
+ };
+ };
+
+ dvi0: connector@0 {
+ compatible = "dvi-connector";
+ label = "dvi";
+
+ i2c-bus = <&i2c3>;
+
+ dvi_connector_in: endpoint {
+ remote-endpoint = <&tfp410_out>;
+ };
+ };
+
+ tv0: connector@1 {
+ compatible = "svideo-connector";
+ label = "tv";
+
+ tv_connector_in: endpoint {
+ remote-endpoint = <&venc_out>;
+ };
+ };
};
&omap3_pmx_wkup {
@@ -94,6 +147,17 @@
0x0e (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE4) /* sys_boot2.gpio_4 */
>;
};
+
+ dss_dpi_pins2: pinmux_dss_dpi_pins {
+ pinctrl-single,pins = <
+ 0x0a (PIN_OUTPUT | MUX_MODE3) /* sys_boot0.dss_data18 */
+ 0x0c (PIN_OUTPUT | MUX_MODE3) /* sys_boot1.dss_data19 */
+ 0x10 (PIN_OUTPUT | MUX_MODE3) /* sys_boot3.dss_data20 */
+ 0x12 (PIN_OUTPUT | MUX_MODE3) /* sys_boot4.dss_data21 */
+ 0x14 (PIN_OUTPUT | MUX_MODE3) /* sys_boot5.dss_data22 */
+ 0x16 (PIN_OUTPUT | MUX_MODE3) /* sys_boot6.dss_data23 */
+ >;
+ };
};
&omap3_pmx_core {
@@ -125,6 +189,35 @@
0x1ae (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */
>;
};
+
+ dss_dpi_pins1: pinmux_dss_dpi_pins {
+ pinctrl-single,pins = <
+ 0x0a4 (PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */
+ 0x0a6 (PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */
+ 0x0a8 (PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */
+ 0x0aa (PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */
+
+ 0x0b8 (PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */
+ 0x0ba (PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */
+ 0x0bc (PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */
+ 0x0be (PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */
+ 0x0c0 (PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */
+ 0x0c2 (PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */
+ 0x0c4 (PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */
+ 0x0c6 (PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */
+ 0x0c8 (PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */
+ 0x0ca (PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */
+ 0x0cc (PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */
+ 0x0ce (PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */
+
+ 0x0d0 (PIN_OUTPUT | MUX_MODE3) /* dss_data18.dss_data0 */
+ 0x0d2 (PIN_OUTPUT | MUX_MODE3) /* dss_data19.dss_data1 */
+ 0x0d4 (PIN_OUTPUT | MUX_MODE3) /* dss_data20.dss_data2 */
+ 0x0d6 (PIN_OUTPUT | MUX_MODE3) /* dss_data21.dss_data3 */
+ 0x0d8 (PIN_OUTPUT | MUX_MODE3) /* dss_data22.dss_data4 */
+ 0x0da (PIN_OUTPUT | MUX_MODE3) /* dss_data23.dss_data5 */
+ >;
+ };
};
&i2c1 {
@@ -222,3 +315,29 @@
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
+
+&dss {
+ status = "ok";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &dss_dpi_pins1
+ &dss_dpi_pins2
+ >;
+
+ dpi_out: endpoint {
+ remote-endpoint = <&tfp410_in>;
+ data-lines = <24>;
+ };
+};
+
+&venc {
+ status = "ok";
+
+ vdda-supply = <&vdac>;
+
+ venc_out: endpoint {
+ remote-endpoint = <&tv_connector_in>;
+ ti,channels = <2>;
+ };
+};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 27/41] ARM: omap3-beagle.dts: add display information
From: Tomi Valkeinen @ 2014-01-21 10:56 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT data for OMAP3 Beagle board. The board has the following displays:
dvi: uses TFP410 encoder to convert DPI to DVI
tv: analog svideo
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
arch/arm/boot/dts/omap3-beagle.dts | 116 +++++++++++++++++++++++++++++++++++++
1 file changed, 116 insertions(+)
diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts
index 3ba4a625ea5b..2b8efe355734 100644
--- a/arch/arm/boot/dts/omap3-beagle.dts
+++ b/arch/arm/boot/dts/omap3-beagle.dts
@@ -24,6 +24,11 @@
reg = <0x80000000 0x10000000>; /* 256 MB */
};
+ aliases {
+ display0 = &dvi0;
+ display1 = &tv0;
+ };
+
leds {
compatible = "gpio-leds";
pmu_stat {
@@ -80,6 +85,55 @@
};
};
+
+ tfp410: encoder@0 {
+ compatible = "ti,tfp410";
+ gpios = <&gpio6 10 GPIO_ACTIVE_LOW>; /* 170, power-down */
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&tfp410_pins>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ tfp410_in: endpoint@0 {
+ remote-endpoint = <&dpi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ tfp410_out: endpoint@0 {
+ remote-endpoint = <&dvi_connector_in>;
+ };
+ };
+ };
+ };
+
+ dvi0: connector@0 {
+ compatible = "dvi-connector";
+ label = "dvi";
+
+ i2c-bus = <&i2c3>;
+
+ dvi_connector_in: endpoint {
+ remote-endpoint = <&tfp410_out>;
+ };
+ };
+
+ tv0: connector@1 {
+ compatible = "svideo-connector";
+ label = "tv";
+
+ tv_connector_in: endpoint {
+ remote-endpoint = <&venc_out>;
+ };
+ };
};
&omap3_pmx_wkup {
@@ -119,6 +173,45 @@
0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */
>;
};
+
+ tfp410_pins: pinmux_tfp410_pins {
+ pinctrl-single,pins = <
+ 0x194 (PIN_OUTPUT | MUX_MODE4) /* hdq_sio.gpio_170 */
+ >;
+ };
+
+ dss_dpi_pins: pinmux_dss_dpi_pins {
+ pinctrl-single,pins = <
+ 0x0a4 (PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */
+ 0x0a6 (PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */
+ 0x0a8 (PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */
+ 0x0aa (PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */
+ 0x0ac (PIN_OUTPUT | MUX_MODE0) /* dss_data0.dss_data0 */
+ 0x0ae (PIN_OUTPUT | MUX_MODE0) /* dss_data1.dss_data1 */
+ 0x0b0 (PIN_OUTPUT | MUX_MODE0) /* dss_data2.dss_data2 */
+ 0x0b2 (PIN_OUTPUT | MUX_MODE0) /* dss_data3.dss_data3 */
+ 0x0b4 (PIN_OUTPUT | MUX_MODE0) /* dss_data4.dss_data4 */
+ 0x0b6 (PIN_OUTPUT | MUX_MODE0) /* dss_data5.dss_data5 */
+ 0x0b8 (PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */
+ 0x0ba (PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */
+ 0x0bc (PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */
+ 0x0be (PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */
+ 0x0c0 (PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */
+ 0x0c2 (PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */
+ 0x0c4 (PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */
+ 0x0c6 (PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */
+ 0x0c8 (PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */
+ 0x0ca (PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */
+ 0x0cc (PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */
+ 0x0ce (PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */
+ 0x0d0 (PIN_OUTPUT | MUX_MODE0) /* dss_data18.dss_data18 */
+ 0x0d2 (PIN_OUTPUT | MUX_MODE0) /* dss_data19.dss_data19 */
+ 0x0d4 (PIN_OUTPUT | MUX_MODE0) /* dss_data20.dss_data20 */
+ 0x0d6 (PIN_OUTPUT | MUX_MODE0) /* dss_data21.dss_data21 */
+ 0x0d8 (PIN_OUTPUT | MUX_MODE0) /* dss_data22.dss_data22 */
+ 0x0da (PIN_OUTPUT | MUX_MODE0) /* dss_data23.dss_data23 */
+ >;
+ };
};
&i2c1 {
@@ -199,3 +292,26 @@
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
+
+&dss {
+ status = "ok";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&dss_dpi_pins>;
+
+ dpi_out: endpoint {
+ remote-endpoint = <&tfp410_in>;
+ data-lines = <24>;
+ };
+};
+
+&venc {
+ status = "ok";
+
+ vdda-supply = <&vdac>;
+
+ venc_out: endpoint {
+ remote-endpoint = <&tv_connector_in>;
+ ti,channels = <2>;
+ };
+};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 26/41] ARM: omap4-sdp.dts: add display information
From: Tomi Valkeinen @ 2014-01-21 10:56 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT data for OMAP4 SDP board. The board has the following displays:
lcd0: a command mode DSI panel connected to OMAP DSI1 encoder
lcd1: a command mode DSI panel connected to OMAP DSI2 encoder
hdmi: OMAP HDMI output with TPD12S015 ESD/level shifter
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
arch/arm/boot/dts/omap4-sdp.dts | 107 +++++++++++++++++++++++++++++++++++++++-
1 file changed, 105 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts
index dbc81fb6ef03..cf9f6cbbd349 100644
--- a/arch/arm/boot/dts/omap4-sdp.dts
+++ b/arch/arm/boot/dts/omap4-sdp.dts
@@ -19,6 +19,12 @@
reg = <0x80000000 0x40000000>; /* 1 GB */
};
+ aliases {
+ display0 = &lcd0;
+ display1 = &lcd1;
+ display2 = &hdmi0;
+ };
+
vdd_eth: fixedregulator-vdd-eth {
compatible = "regulator-fixed";
regulator-name = "VDD_ETH";
@@ -153,6 +159,47 @@
startup-delay-us = <70000>;
enable-active-high;
};
+
+ tpd12s015: encoder@0 {
+ compatible = "ti,tpd12s015";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&tpd12s015_pins>;
+
+ gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>, /* 60, CT CP HPD */
+ <&gpio2 9 GPIO_ACTIVE_HIGH>, /* 41, LS OE */
+ <&gpio2 31 GPIO_ACTIVE_HIGH>; /* 63, HPD */
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ tpd12s015_in: endpoint@0 {
+ remote-endpoint = <&hdmi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ tpd12s015_out: endpoint@0 {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+ };
+ };
+ };
+
+ hdmi0: connector@0 {
+ compatible = "hdmi-connector";
+ label = "hdmi";
+
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&tpd12s015_out>;
+ };
+ };
};
&omap4_pmx_core {
@@ -163,8 +210,6 @@
&dmic_pins
&mcbsp1_pins
&mcbsp2_pins
- &dss_hdmi_pins
- &tpd12s015_pins
>;
uart2_pins: pinmux_uart2_pins {
@@ -550,3 +595,61 @@
mode = <3>;
power = <50>;
};
+
+&dss {
+ status = "ok";
+};
+
+&dsi1 {
+ status = "ok";
+ vdd-supply = <&vcxio>;
+
+ dsi1_out_ep: endpoint {
+ remote-endpoint = <&lcd0_in>;
+ lanes = <0 1 2 3 4 5>;
+ };
+
+ lcd0: display {
+ compatible = "tpo,taal", "panel-dsi-cm";
+ label = "lcd0";
+
+ gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* 102, reset */
+
+ lcd0_in: endpoint {
+ remote-endpoint = <&dsi1_out_ep>;
+ };
+ };
+};
+
+&dsi2 {
+ status = "ok";
+ vdd-supply = <&vcxio>;
+
+ dsi2_out_ep: endpoint {
+ remote-endpoint = <&lcd1_in>;
+ lanes = <0 1 2 3 4 5>;
+ };
+
+ lcd1: display {
+ compatible = "tpo,taal", "panel-dsi-cm";
+ label = "lcd1";
+
+ gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* 104, reset */
+
+ lcd1_in: endpoint {
+ remote-endpoint = <&dsi2_out_ep>;
+ };
+ };
+};
+
+&hdmi {
+ status = "ok";
+ vdda-supply = <&vdac>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&dss_hdmi_pins>;
+
+ hdmi_out: endpoint {
+ remote-endpoint = <&tpd12s015_in>;
+ };
+};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 25/41] ARM: omap4-panda.dts: add display information
From: Tomi Valkeinen @ 2014-01-21 10:56 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT data for OMAP4 Pandaboard. The board has the following displays:
dvi: uses TFP410 encoder to convert DPI to DVI
hdmi: OMAP HDMI output with TPD12S015 ESD/level shifter
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
arch/arm/boot/dts/omap4-panda-common.dtsi | 119 +++++++++++++++++++++++++++++-
1 file changed, 115 insertions(+), 4 deletions(-)
diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi
index 88c6a05cab41..20aa18ff4823 100644
--- a/arch/arm/boot/dts/omap4-panda-common.dtsi
+++ b/arch/arm/boot/dts/omap4-panda-common.dtsi
@@ -16,6 +16,11 @@
reg = <0x80000000 0x40000000>; /* 1 GB */
};
+ aliases {
+ display0 = &dvi0;
+ display1 = &hdmi0;
+ };
+
leds: leds {
compatible = "gpio-leds";
pinctrl-names = "default";
@@ -104,6 +109,87 @@
startup-delay-us = <70000>;
enable-active-high;
};
+
+ tfp410: encoder@0 {
+ compatible = "ti,tfp410";
+ gpios = <&gpio1 0 GPIO_ACTIVE_LOW>; /* 0, power-down */
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&tfp410_pins>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ tfp410_in: endpoint@0 {
+ remote-endpoint = <&dpi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ tfp410_out: endpoint@0 {
+ remote-endpoint = <&dvi_connector_in>;
+ };
+ };
+ };
+ };
+
+ dvi0: connector@0 {
+ compatible = "dvi-connector";
+ label = "dvi";
+
+ i2c-bus = <&i2c3>;
+
+ dvi_connector_in: endpoint {
+ remote-endpoint = <&tfp410_out>;
+ };
+ };
+
+ tpd12s015: encoder@1 {
+ compatible = "ti,tpd12s015";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&tpd12s015_pins>;
+
+ gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>, /* 60, CT CP HPD */
+ <&gpio2 9 GPIO_ACTIVE_HIGH>, /* 41, LS OE */
+ <&gpio2 31 GPIO_ACTIVE_HIGH>; /* 63, HPD */
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ tpd12s015_in: endpoint@0 {
+ remote-endpoint = <&hdmi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ tpd12s015_out: endpoint@0 {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+ };
+ };
+ };
+
+ hdmi0: connector@1 {
+ compatible = "hdmi-connector";
+ label = "hdmi";
+
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&tpd12s015_out>;
+ };
+ };
};
&omap4_pmx_core {
@@ -112,10 +198,6 @@
&twl6040_pins
&mcpdm_pins
&mcbsp1_pins
- &dss_dpi_pins
- &tfp410_pins
- &dss_hdmi_pins
- &tpd12s015_pins
&hsusbb1_pins
>;
@@ -409,3 +491,32 @@
&usbhsehci {
phys = <&hsusb1_phy>;
};
+
+&dss {
+ status = "ok";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&dss_dpi_pins>;
+
+ dpi_out: endpoint {
+ remote-endpoint = <&tfp410_in>;
+ data-lines = <24>;
+ };
+};
+
+&dsi2 {
+ status = "ok";
+ vdd-supply = <&vcxio>;
+};
+
+&hdmi {
+ status = "ok";
+ vdda-supply = <&vdac>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&dss_hdmi_pins>;
+
+ hdmi_out: endpoint {
+ remote-endpoint = <&tpd12s015_in>;
+ };
+};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 24/41] ARM: omap4.dtsi: add omapdss information
From: Tomi Valkeinen @ 2014-01-21 10:56 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT data for OMAP4 display subsystem, which contains the following
blocks:
dss - the wrapper/glue for the display modules
dispc - display controller
dsi - MIPI DSI encoder (two independent modules)
rfbi - MIPI DBI encoder
venc - analog TV encoder
hdmi - HDMI encoder
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
arch/arm/boot/dts/omap4.dtsi | 65 ++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 65 insertions(+)
diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
index a1e05853afcd..19498b2fa316 100644
--- a/arch/arm/boot/dts/omap4.dtsi
+++ b/arch/arm/boot/dts/omap4.dtsi
@@ -705,5 +705,70 @@
dmas = <&sdma 117>, <&sdma 116>;
dma-names = "tx", "rx";
};
+
+ dss: dss@58000000 {
+ compatible = "ti,omap4-dss", "simple-bus";
+ reg = <0x58000000 0x80>;
+ status = "disabled";
+ ti,hwmods = "dss_core";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ dispc@58001000 {
+ compatible = "ti,omap4-dispc";
+ reg = <0x58001000 0x1000>;
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "dss_dispc";
+ };
+
+ rfbi: encoder@58002000 {
+ compatible = "ti,omap4-rfbi";
+ reg = <0x58002000 0x1000>;
+ status = "disabled";
+ ti,hwmods = "dss_rfbi";
+ };
+
+ venc: encoder@58003000 {
+ compatible = "ti,omap4-venc";
+ reg = <0x58003000 0x1000>;
+ status = "disabled";
+ ti,hwmods = "dss_venc";
+ };
+
+ dsi1: encoder@58004000 {
+ compatible = "ti,omap4-dsi";
+ reg = <0x58004000 0x200>,
+ <0x58004200 0x40>,
+ <0x58004300 0x20>;
+ reg-names = "proto", "phy", "pll";
+ interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ ti,hwmods = "dss_dsi1";
+ };
+
+ dsi2: encoder@58005000 {
+ compatible = "ti,omap4-dsi";
+ reg = <0x58005000 0x200>,
+ <0x58005200 0x40>,
+ <0x58005300 0x20>;
+ reg-names = "proto", "phy", "pll";
+ interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ ti,hwmods = "dss_dsi2";
+ };
+
+ hdmi: encoder@58006000 {
+ compatible = "ti,omap4-hdmi";
+ reg = <0x58006000 0x200>,
+ <0x58006200 0x100>,
+ <0x58006300 0x100>,
+ <0x58006400 0x1000>;
+ reg-names = "wp", "pll", "phy", "core";
+ interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ ti,hwmods = "dss_hdmi";
+ };
+ };
};
};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 23/41] ARM: omap3.dtsi: add omapdss information
From: Tomi Valkeinen @ 2014-01-21 10:56 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT data for OMAP3 display subsystem, which contains the following
blocks:
dss - the wrapper/glue for the display modules
dispc - display controller
dsi - MIPI DSI encoder
rfbi - MIPI DBI encoder
venc - analog TV encoder
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
arch/arm/boot/dts/omap3.dtsi | 42 ++++++++++++++++++++++++++++++++++++++++++
1 file changed, 42 insertions(+)
diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi
index daabf99d402a..d942f9a4723f 100644
--- a/arch/arm/boot/dts/omap3.dtsi
+++ b/arch/arm/boot/dts/omap3.dtsi
@@ -630,5 +630,47 @@
num-eps = <16>;
ram-bits = <12>;
};
+
+ dss: dss@48050000 {
+ compatible = "ti,omap3-dss", "simple-bus";
+ reg = <0x48050000 0x200>;
+ status = "disabled";
+ ti,hwmods = "dss_core";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ dispc@48050400 {
+ compatible = "ti,omap3-dispc";
+ reg = <0x48050400 0x400>;
+ interrupts = <25>;
+ ti,hwmods = "dss_dispc";
+ };
+
+ dsi: encoder@4804fc00 {
+ compatible = "ti,omap3-dsi";
+ reg = <0x4804fc00 0x200>,
+ <0x4804fe00 0x40>,
+ <0x4804ff00 0x20>;
+ reg-names = "proto", "phy", "pll";
+ interrupts = <25>;
+ status = "disabled";
+ ti,hwmods = "dss_dsi1";
+ };
+
+ rfbi: encoder@48050800 {
+ compatible = "ti,omap3-rfbi";
+ reg = <0x48050800 0x100>;
+ status = "disabled";
+ ti,hwmods = "dss_rfbi";
+ };
+
+ venc: encoder@48050c00 {
+ compatible = "ti,omap3-venc";
+ reg = <0x48050c00 0x100>;
+ status = "disabled";
+ ti,hwmods = "dss_venc";
+ };
+ };
};
};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 22/41] ARM: omap2.dtsi: add omapdss information
From: Tomi Valkeinen @ 2014-01-21 10:56 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT data for OMAP2 display subsystem, which contains the following
blocks:
dss - the wrapper/glue for the display modules
dispc - display controller
rfbi - MIPI DBI encoder
venc - analog TV encoder
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
arch/arm/boot/dts/omap2.dtsi | 31 +++++++++++++++++++++++++++++++
1 file changed, 31 insertions(+)
diff --git a/arch/arm/boot/dts/omap2.dtsi b/arch/arm/boot/dts/omap2.dtsi
index d0c5b37e248c..af3531cc4576 100644
--- a/arch/arm/boot/dts/omap2.dtsi
+++ b/arch/arm/boot/dts/omap2.dtsi
@@ -271,5 +271,36 @@
ti,hwmods = "timer12";
ti,timer-pwm;
};
+
+ dss: dss@48050000 {
+ compatible = "ti,omap2-dss", "simple-bus";
+ reg = <0x48050000 0x400>;
+ status = "disabled";
+ ti,hwmods = "dss_core";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ dispc@48050400 {
+ compatible = "ti,omap2-dispc";
+ reg = <0x48050400 0x400>;
+ interrupts = <25>;
+ ti,hwmods = "dss_dispc";
+ };
+
+ rfbi: encoder@48050800 {
+ compatible = "ti,omap2-rfbi";
+ reg = <0x48050800 0x400>;
+ status = "disabled";
+ ti,hwmods = "dss_rfbi";
+ };
+
+ venc: encoder@48050c00 {
+ compatible = "ti,omap2-venc";
+ reg = <0x48050c00 0x400>;
+ status = "disabled";
+ ti,hwmods = "dss_venc";
+ };
+ };
};
};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 21/41] OMAPDSS: acx565akm: Add DT support
From: Tomi Valkeinen @ 2014-01-21 10:56 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
From: Sebastian Reichel <sre@debian.org>
Add DT support for panel-sony-acx565akm
Signed-off-by: Sebastian Reichel <sre@debian.org>
[tomi.valkeinen@ti.com: some modifications]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
.../omap2/displays-new/panel-sony-acx565akm.c | 33 +++++++++++++++++++++-
1 file changed, 32 insertions(+), 1 deletion(-)
diff --git a/drivers/video/omap2/displays-new/panel-sony-acx565akm.c b/drivers/video/omap2/displays-new/panel-sony-acx565akm.c
index 8e97d06921ff..8d2745ce55e3 100644
--- a/drivers/video/omap2/displays-new/panel-sony-acx565akm.c
+++ b/drivers/video/omap2/displays-new/panel-sony-acx565akm.c
@@ -30,6 +30,8 @@
#include <linux/backlight.h>
#include <linux/fb.h>
#include <linux/gpio.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
#include <video/omapdss.h>
#include <video/omap-panel-data.h>
@@ -547,7 +549,9 @@ static int acx565akm_panel_power_on(struct omap_dss_device *dssdev)
dev_dbg(&ddata->spi->dev, "%s\n", __func__);
in->ops.sdi->set_timings(in, &ddata->videomode);
- in->ops.sdi->set_datapairs(in, ddata->datapairs);
+
+ if (ddata->datapairs > 0)
+ in->ops.sdi->set_datapairs(in, ddata->datapairs);
r = in->ops.sdi->enable(in);
if (r) {
@@ -726,6 +730,22 @@ static int acx565akm_probe_pdata(struct spi_device *spi)
return 0;
}
+static int acx565akm_probe_of(struct spi_device *spi)
+{
+ struct panel_drv_data *ddata = dev_get_drvdata(&spi->dev);
+ struct device_node *np = spi->dev.of_node;
+
+ ddata->reset_gpio = of_get_gpio(np, 0);
+
+ ddata->in = omapdss_of_find_source_for_first_ep(np);
+ if (IS_ERR(ddata->in)) {
+ dev_err(&spi->dev, "failed to find video source\n");
+ return PTR_ERR(ddata->in);
+ }
+
+ return 0;
+}
+
static int acx565akm_probe(struct spi_device *spi)
{
struct panel_drv_data *ddata;
@@ -753,7 +773,12 @@ static int acx565akm_probe(struct spi_device *spi)
r = acx565akm_probe_pdata(spi);
if (r)
return r;
+ } else if (spi->dev.of_node) {
+ r = acx565akm_probe_of(spi);
+ if (r)
+ return r;
} else {
+ dev_err(&spi->dev, "platform data missing!\n");
return -ENODEV;
}
@@ -864,10 +889,16 @@ static int acx565akm_remove(struct spi_device *spi)
return 0;
}
+static const struct of_device_id acx565akm_of_match[] = {
+ { .compatible = "omapdss,sony,acx565akm", },
+ {},
+};
+
static struct spi_driver acx565akm_driver = {
.driver = {
.name = "acx565akm",
.owner = THIS_MODULE,
+ .of_match_table = acx565akm_of_match,
},
.probe = acx565akm_probe,
.remove = acx565akm_remove,
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 20/41] OMAPDSS: connector-analog-tv: Add DT support
From: Tomi Valkeinen @ 2014-01-21 10:56 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT support for connector-analog-tv.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
.../video/omap2/displays-new/connector-analog-tv.c | 43 +++++++++++++++++++++-
1 file changed, 41 insertions(+), 2 deletions(-)
diff --git a/drivers/video/omap2/displays-new/connector-analog-tv.c b/drivers/video/omap2/displays-new/connector-analog-tv.c
index ccd9073f706f..5c840325def4 100644
--- a/drivers/video/omap2/displays-new/connector-analog-tv.c
+++ b/drivers/video/omap2/displays-new/connector-analog-tv.c
@@ -12,6 +12,7 @@
#include <linux/slab.h>
#include <linux/module.h>
#include <linux/platform_device.h>
+#include <linux/of.h>
#include <video/omapdss.h>
#include <video/omap-panel-data.h>
@@ -42,6 +43,12 @@ static const struct omap_video_timings tvc_pal_timings = {
.interlace = true,
};
+static const struct of_device_id tvc_of_match[];
+
+struct tvc_of_data {
+ enum omap_dss_venc_type connector_type;
+};
+
#define to_panel_data(x) container_of(x, struct panel_drv_data, dssdev)
static int tvc_connect(struct omap_dss_device *dssdev)
@@ -91,8 +98,12 @@ static int tvc_enable(struct omap_dss_device *dssdev)
in->ops.atv->set_timings(in, &ddata->timings);
- in->ops.atv->set_type(in, ddata->connector_type);
- in->ops.atv->invert_vid_out_polarity(in, ddata->invert_polarity);
+ if (!ddata->dev->of_node) {
+ in->ops.atv->set_type(in, ddata->connector_type);
+
+ in->ops.atv->invert_vid_out_polarity(in,
+ ddata->invert_polarity);
+ }
r = in->ops.atv->enable(in);
if (r)
@@ -205,6 +216,23 @@ static int tvc_probe_pdata(struct platform_device *pdev)
return 0;
}
+static int tvc_probe_of(struct platform_device *pdev)
+{
+ struct panel_drv_data *ddata = platform_get_drvdata(pdev);
+ struct device_node *node = pdev->dev.of_node;
+ struct omap_dss_device *in;
+
+ in = omapdss_of_find_source_for_first_ep(node);
+ if (IS_ERR(in)) {
+ dev_err(&pdev->dev, "failed to find video source\n");
+ return PTR_ERR(in);
+ }
+
+ ddata->in = in;
+
+ return 0;
+}
+
static int tvc_probe(struct platform_device *pdev)
{
struct panel_drv_data *ddata;
@@ -222,6 +250,10 @@ static int tvc_probe(struct platform_device *pdev)
r = tvc_probe_pdata(pdev);
if (r)
return r;
+ } else if (pdev->dev.of_node) {
+ r = tvc_probe_of(pdev);
+ if (r)
+ return r;
} else {
return -ENODEV;
}
@@ -263,12 +295,19 @@ static int __exit tvc_remove(struct platform_device *pdev)
return 0;
}
+static const struct of_device_id tvc_of_match[] = {
+ { .compatible = "omapdss,svideo-connector", },
+ { .compatible = "omapdss,composite-video-connector", },
+ {},
+};
+
static struct platform_driver tvc_connector_driver = {
.probe = tvc_probe,
.remove = __exit_p(tvc_remove),
.driver = {
.name = "connector-analog-tv",
.owner = THIS_MODULE,
+ .of_match_table = tvc_of_match,
},
};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 19/41] OMAPDSS: panel-dpi: Add DT support
From: Tomi Valkeinen @ 2014-01-21 10:56 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT support for panel-dpi.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
drivers/video/omap2/displays-new/panel-dpi.c | 64 +++++++++++++++++++++++++++-
1 file changed, 63 insertions(+), 1 deletion(-)
diff --git a/drivers/video/omap2/displays-new/panel-dpi.c b/drivers/video/omap2/displays-new/panel-dpi.c
index 5f8f7e7c81ef..b032daf0f407 100644
--- a/drivers/video/omap2/displays-new/panel-dpi.c
+++ b/drivers/video/omap2/displays-new/panel-dpi.c
@@ -13,9 +13,12 @@
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/slab.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
#include <video/omapdss.h>
#include <video/omap-panel-data.h>
+#include <video/of_display_timing.h>
struct panel_drv_data {
struct omap_dss_device dssdev;
@@ -70,7 +73,8 @@ static int panel_dpi_enable(struct omap_dss_device *dssdev)
if (omapdss_device_is_enabled(dssdev))
return 0;
- in->ops.dpi->set_data_lines(in, ddata->data_lines);
+ if (ddata->data_lines)
+ in->ops.dpi->set_data_lines(in, ddata->data_lines);
in->ops.dpi->set_timings(in, &ddata->videomode);
r = in->ops.dpi->enable(in);
@@ -182,6 +186,52 @@ static int panel_dpi_probe_pdata(struct platform_device *pdev)
return 0;
}
+static int panel_dpi_probe_of(struct platform_device *pdev)
+{
+ struct panel_drv_data *ddata = platform_get_drvdata(pdev);
+ struct device_node *node = pdev->dev.of_node;
+ struct omap_dss_device *in;
+ int r;
+ struct display_timing timing;
+ struct videomode vm;
+ int gpio;
+
+ gpio = of_get_gpio(node, 0);
+ if (gpio_is_valid(gpio) || gpio = -ENOENT) {
+ ddata->enable_gpio = gpio;
+ } else {
+ dev_err(&pdev->dev, "failed to parse enable gpio\n");
+ return gpio;
+ }
+
+ gpio = of_get_gpio(node, 1);
+ if (gpio_is_valid(gpio) || gpio = -ENOENT) {
+ ddata->backlight_gpio = gpio;
+ } else {
+ dev_err(&pdev->dev, "failed to parse backlight gpio\n");
+ return gpio;
+ }
+
+ r = of_get_display_timing(node, "panel-timing", &timing);
+ if (r) {
+ dev_err(&pdev->dev, "failed to get video timing\n");
+ return r;
+ }
+
+ videomode_from_timing(&timing, &vm);
+ videomode_to_omap_video_timings(&vm, &ddata->videomode);
+
+ in = omapdss_of_find_source_for_first_ep(node);
+ if (IS_ERR(in)) {
+ dev_err(&pdev->dev, "failed to find video source\n");
+ return PTR_ERR(in);
+ }
+
+ ddata->in = in;
+
+ return 0;
+}
+
static int panel_dpi_probe(struct platform_device *pdev)
{
struct panel_drv_data *ddata;
@@ -198,6 +248,10 @@ static int panel_dpi_probe(struct platform_device *pdev)
r = panel_dpi_probe_pdata(pdev);
if (r)
return r;
+ } else if (pdev->dev.of_node) {
+ r = panel_dpi_probe_of(pdev);
+ if (r)
+ return r;
} else {
return -ENODEV;
}
@@ -254,12 +308,20 @@ static int __exit panel_dpi_remove(struct platform_device *pdev)
return 0;
}
+static const struct of_device_id panel_dpi_of_match[] = {
+ { .compatible = "omapdss,panel-dpi", },
+ {},
+};
+
+MODULE_DEVICE_TABLE(of, panel_dpi_of_match);
+
static struct platform_driver panel_dpi_driver = {
.probe = panel_dpi_probe,
.remove = __exit_p(panel_dpi_remove),
.driver = {
.name = "panel-dpi",
.owner = THIS_MODULE,
+ .of_match_table = panel_dpi_of_match,
},
};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 18/41] OMAPDSS: hdmi-connector: Add DT support
From: Tomi Valkeinen @ 2014-01-21 10:56 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT support for hdmi-connector.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
drivers/video/omap2/displays-new/connector-hdmi.c | 30 +++++++++++++++++++++++
1 file changed, 30 insertions(+)
diff --git a/drivers/video/omap2/displays-new/connector-hdmi.c b/drivers/video/omap2/displays-new/connector-hdmi.c
index 9abe2c039ae9..2e026eab2dd0 100644
--- a/drivers/video/omap2/displays-new/connector-hdmi.c
+++ b/drivers/video/omap2/displays-new/connector-hdmi.c
@@ -12,6 +12,7 @@
#include <linux/slab.h>
#include <linux/module.h>
#include <linux/platform_device.h>
+#include <linux/of.h>
#include <drm/drm_edid.h>
@@ -301,6 +302,23 @@ static int hdmic_probe_pdata(struct platform_device *pdev)
return 0;
}
+static int hdmic_probe_of(struct platform_device *pdev)
+{
+ struct panel_drv_data *ddata = platform_get_drvdata(pdev);
+ struct device_node *node = pdev->dev.of_node;
+ struct omap_dss_device *in;
+
+ in = omapdss_of_find_source_for_first_ep(node);
+ if (IS_ERR(in)) {
+ dev_err(&pdev->dev, "failed to find video source\n");
+ return PTR_ERR(in);
+ }
+
+ ddata->in = in;
+
+ return 0;
+}
+
static int hdmic_probe(struct platform_device *pdev)
{
struct panel_drv_data *ddata;
@@ -318,6 +336,10 @@ static int hdmic_probe(struct platform_device *pdev)
r = hdmic_probe_pdata(pdev);
if (r)
return r;
+ } else if (pdev->dev.of_node) {
+ r = hdmic_probe_of(pdev);
+ if (r)
+ return r;
} else {
return -ENODEV;
}
@@ -359,12 +381,20 @@ static int __exit hdmic_remove(struct platform_device *pdev)
return 0;
}
+static const struct of_device_id hdmic_of_match[] = {
+ { .compatible = "omapdss,hdmi-connector", },
+ {},
+};
+
+MODULE_DEVICE_TABLE(of, hdmic_of_match);
+
static struct platform_driver hdmi_connector_driver = {
.probe = hdmic_probe,
.remove = __exit_p(hdmic_remove),
.driver = {
.name = "connector-hdmi",
.owner = THIS_MODULE,
+ .of_match_table = hdmic_of_match,
},
};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 17/41] OMAPDSS: encoder-tpd12s015: Add DT support
From: Tomi Valkeinen @ 2014-01-21 10:56 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT support for encoder-tpd12s015.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
.../video/omap2/displays-new/encoder-tpd12s015.c | 56 ++++++++++++++++++++++
1 file changed, 56 insertions(+)
diff --git a/drivers/video/omap2/displays-new/encoder-tpd12s015.c b/drivers/video/omap2/displays-new/encoder-tpd12s015.c
index d5c936cb217f..7e33686171e3 100644
--- a/drivers/video/omap2/displays-new/encoder-tpd12s015.c
+++ b/drivers/video/omap2/displays-new/encoder-tpd12s015.c
@@ -15,6 +15,7 @@
#include <linux/slab.h>
#include <linux/gpio.h>
#include <linux/platform_device.h>
+#include <linux/of_gpio.h>
#include <video/omapdss.h>
#include <video/omap-panel-data.h>
@@ -289,6 +290,49 @@ static int tpd_probe_pdata(struct platform_device *pdev)
return 0;
}
+static int tpd_probe_of(struct platform_device *pdev)
+{
+ struct panel_drv_data *ddata = platform_get_drvdata(pdev);
+ struct device_node *node = pdev->dev.of_node;
+ struct omap_dss_device *in;
+ int gpio;
+
+ /* CT CP HPD GPIO */
+ gpio = of_get_gpio(node, 0);
+ if (!gpio_is_valid(gpio)) {
+ dev_err(&pdev->dev, "failed to parse CT CP HPD gpio\n");
+ return gpio;
+ }
+ ddata->ct_cp_hpd_gpio = gpio;
+
+ /* LS OE GPIO */
+ gpio = of_get_gpio(node, 1);
+ if (gpio_is_valid(gpio) || gpio = -ENOENT) {
+ ddata->ls_oe_gpio = gpio;
+ } else {
+ dev_err(&pdev->dev, "failed to parse LS OE gpio\n");
+ return gpio;
+ }
+
+ /* HPD GPIO */
+ gpio = of_get_gpio(node, 2);
+ if (!gpio_is_valid(gpio)) {
+ dev_err(&pdev->dev, "failed to parse HPD gpio\n");
+ return gpio;
+ }
+ ddata->hpd_gpio = gpio;
+
+ in = omapdss_of_find_source_for_first_ep(node);
+ if (IS_ERR(in)) {
+ dev_err(&pdev->dev, "failed to find video source\n");
+ return PTR_ERR(in);
+ }
+
+ ddata->in = in;
+
+ return 0;
+}
+
static int tpd_probe(struct platform_device *pdev)
{
struct omap_dss_device *in, *dssdev;
@@ -307,6 +351,10 @@ static int tpd_probe(struct platform_device *pdev)
r = tpd_probe_pdata(pdev);
if (r)
return r;
+ } else if (pdev->dev.of_node) {
+ r = tpd_probe_of(pdev);
+ if (r)
+ return r;
} else {
return -ENODEV;
}
@@ -379,12 +427,20 @@ static int __exit tpd_remove(struct platform_device *pdev)
return 0;
}
+static const struct of_device_id tpd_of_match[] = {
+ { .compatible = "omapdss,ti,tpd12s015", },
+ {},
+};
+
+MODULE_DEVICE_TABLE(of, tpd_of_match);
+
static struct platform_driver tpd_driver = {
.probe = tpd_probe,
.remove = __exit_p(tpd_remove),
.driver = {
.name = "tpd12s015",
.owner = THIS_MODULE,
+ .of_match_table = tpd_of_match,
},
};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 16/41] OMAPDSS: connector-dvi: Add DT support
From: Tomi Valkeinen @ 2014-01-21 10:56 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT support for connector-dvi.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
drivers/video/omap2/displays-new/connector-dvi.c | 43 ++++++++++++++++++++++++
1 file changed, 43 insertions(+)
diff --git a/drivers/video/omap2/displays-new/connector-dvi.c b/drivers/video/omap2/displays-new/connector-dvi.c
index b6c50904038e..4ea26abdcb64 100644
--- a/drivers/video/omap2/displays-new/connector-dvi.c
+++ b/drivers/video/omap2/displays-new/connector-dvi.c
@@ -277,6 +277,37 @@ static int dvic_probe_pdata(struct platform_device *pdev)
return 0;
}
+static int dvic_probe_of(struct platform_device *pdev)
+{
+ struct panel_drv_data *ddata = platform_get_drvdata(pdev);
+ struct device_node *node = pdev->dev.of_node;
+ struct omap_dss_device *in;
+ struct device_node *adapter_node;
+ struct i2c_adapter *adapter;
+
+ in = omapdss_of_find_source_for_first_ep(node);
+ if (IS_ERR(in)) {
+ dev_err(&pdev->dev, "failed to find video source\n");
+ return PTR_ERR(in);
+ }
+
+ ddata->in = in;
+
+ adapter_node = of_parse_phandle(node, "i2c-bus", 0);
+ if (adapter_node) {
+ adapter = of_find_i2c_adapter_by_node(adapter_node);
+ if (adapter = NULL) {
+ dev_err(&pdev->dev, "failed to parse i2c-bus\n");
+ omap_dss_put_device(ddata->in);
+ return -EPROBE_DEFER;
+ }
+
+ ddata->i2c_adapter = adapter;
+ }
+
+ return 0;
+}
+
static int dvic_probe(struct platform_device *pdev)
{
struct panel_drv_data *ddata;
@@ -293,6 +324,10 @@ static int dvic_probe(struct platform_device *pdev)
r = dvic_probe_pdata(pdev);
if (r)
return r;
+ } else if (pdev->dev.of_node) {
+ r = dvic_probe_of(pdev);
+ if (r)
+ return r;
} else {
return -ENODEV;
}
@@ -342,12 +377,20 @@ static int __exit dvic_remove(struct platform_device *pdev)
return 0;
}
+static const struct of_device_id dvic_of_match[] = {
+ { .compatible = "omapdss,dvi-connector", },
+ {},
+};
+
+MODULE_DEVICE_TABLE(of, dvic_of_match);
+
static struct platform_driver dvi_connector_driver = {
.probe = dvic_probe,
.remove = __exit_p(dvic_remove),
.driver = {
.name = "connector-dvi",
.owner = THIS_MODULE,
+ .of_match_table = dvic_of_match,
},
};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 15/41] OMAPDSS: encoder-tfp410: Add DT support
From: Tomi Valkeinen @ 2014-01-21 10:56 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT support for encoder-tfp410.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
drivers/video/omap2/displays-new/encoder-tfp410.c | 43 ++++++++++++++++++++++-
1 file changed, 42 insertions(+), 1 deletion(-)
diff --git a/drivers/video/omap2/displays-new/encoder-tfp410.c b/drivers/video/omap2/displays-new/encoder-tfp410.c
index 4a291e756be9..e1ef972e33cd 100644
--- a/drivers/video/omap2/displays-new/encoder-tfp410.c
+++ b/drivers/video/omap2/displays-new/encoder-tfp410.c
@@ -13,6 +13,7 @@
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/slab.h>
+#include <linux/of_gpio.h>
#include <video/omapdss.h>
#include <video/omap-panel-data.h>
@@ -82,7 +83,8 @@ static int tfp410_enable(struct omap_dss_device *dssdev)
return 0;
in->ops.dpi->set_timings(in, &ddata->timings);
- in->ops.dpi->set_data_lines(in, ddata->data_lines);
+ if (ddata->data_lines)
+ in->ops.dpi->set_data_lines(in, ddata->data_lines);
r = in->ops.dpi->enable(in);
if (r)
@@ -179,6 +181,33 @@ static int tfp410_probe_pdata(struct platform_device *pdev)
return 0;
}
+static int tfp410_probe_of(struct platform_device *pdev)
+{
+ struct panel_drv_data *ddata = platform_get_drvdata(pdev);
+ struct device_node *node = pdev->dev.of_node;
+ struct omap_dss_device *in;
+ int gpio;
+
+ gpio = of_get_gpio(node, 0);
+
+ if (gpio_is_valid(gpio) || gpio = -ENOENT) {
+ ddata->pd_gpio = gpio;
+ } else {
+ dev_err(&pdev->dev, "failed to parse PD gpio\n");
+ return gpio;
+ }
+
+ in = omapdss_of_find_source_for_first_ep(node);
+ if (IS_ERR(in)) {
+ dev_err(&pdev->dev, "failed to find video source\n");
+ return PTR_ERR(in);
+ }
+
+ ddata->in = in;
+
+ return 0;
+}
+
static int tfp410_probe(struct platform_device *pdev)
{
struct panel_drv_data *ddata;
@@ -195,6 +224,10 @@ static int tfp410_probe(struct platform_device *pdev)
r = tfp410_probe_pdata(pdev);
if (r)
return r;
+ } else if (pdev->dev.of_node) {
+ r = tfp410_probe_of(pdev);
+ if (r)
+ return r;
} else {
return -ENODEV;
}
@@ -251,12 +284,20 @@ static int __exit tfp410_remove(struct platform_device *pdev)
return 0;
}
+static const struct of_device_id tfp410_of_match[] = {
+ { .compatible = "omapdss,ti,tfp410", },
+ {},
+};
+
+MODULE_DEVICE_TABLE(of, tfp410_of_match);
+
static struct platform_driver tfp410_driver = {
.probe = tfp410_probe,
.remove = __exit_p(tfp410_remove),
.driver = {
.name = "tfp410",
.owner = THIS_MODULE,
+ .of_match_table = tfp410_of_match,
},
};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 14/41] OMAPDSS: panel-dsi-cm: Add DT support
From: Tomi Valkeinen @ 2014-01-21 10:56 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT support for panel-dsi-cm.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
drivers/video/omap2/displays-new/panel-dsi-cm.c | 65 +++++++++++++++++++++++--
1 file changed, 61 insertions(+), 4 deletions(-)
diff --git a/drivers/video/omap2/displays-new/panel-dsi-cm.c b/drivers/video/omap2/displays-new/panel-dsi-cm.c
index b7baafe83aa3..d302c4428ab7 100644
--- a/drivers/video/omap2/displays-new/panel-dsi-cm.c
+++ b/drivers/video/omap2/displays-new/panel-dsi-cm.c
@@ -22,6 +22,8 @@
#include <linux/sched.h>
#include <linux/slab.h>
#include <linux/workqueue.h>
+#include <linux/of_device.h>
+#include <linux/of_gpio.h>
#include <video/omapdss.h>
#include <video/omap-panel-data.h>
@@ -595,10 +597,13 @@ static int dsicm_power_on(struct panel_drv_data *ddata)
.lp_clk_max = 10000000,
};
- r = in->ops.dsi->configure_pins(in, &ddata->pin_config);
- if (r) {
- dev_err(&ddata->pdev->dev, "failed to configure DSI pins\n");
- goto err0;
+ if (ddata->pin_config.num_pins > 0) {
+ r = in->ops.dsi->configure_pins(in, &ddata->pin_config);
+ if (r) {
+ dev_err(&ddata->pdev->dev,
+ "failed to configure DSI pins\n");
+ goto err0;
+ }
}
r = in->ops.dsi->set_config(in, &dsi_config);
@@ -1156,6 +1161,46 @@ static int dsicm_probe_pdata(struct platform_device *pdev)
return 0;
}
+static int dsicm_probe_of(struct platform_device *pdev)
+{
+ struct device_node *node = pdev->dev.of_node;
+ struct panel_drv_data *ddata = platform_get_drvdata(pdev);
+ struct omap_dss_device *in;
+ int gpio;
+
+ gpio = of_get_gpio(node, 0);
+ if (!gpio_is_valid(gpio)) {
+ dev_err(&pdev->dev, "failed to parse reset gpio\n");
+ return gpio;
+ }
+ ddata->reset_gpio = gpio;
+
+ if (of_gpio_count(node) > 1) {
+ gpio = of_get_gpio(node, 1);
+
+ if (gpio_is_valid(gpio) || gpio = -ENOENT) {
+ ddata->ext_te_gpio = gpio;
+ } else {
+ dev_err(&pdev->dev, "failed to parse TE gpio\n");
+ return gpio;
+ }
+ } else {
+ ddata->ext_te_gpio = -1;
+ }
+
+ in = omapdss_of_find_source_for_first_ep(node);
+ if (IS_ERR(in)) {
+ dev_err(&pdev->dev, "failed to find video source\n");
+ return PTR_ERR(in);
+ }
+
+ ddata->in = in;
+
+ /* TODO: ulps, backlight */
+
+ return 0;
+}
+
static int dsicm_probe(struct platform_device *pdev)
{
struct backlight_properties props;
@@ -1178,6 +1223,10 @@ static int dsicm_probe(struct platform_device *pdev)
r = dsicm_probe_pdata(pdev);
if (r)
return r;
+ } else if (pdev->dev.of_node) {
+ r = dsicm_probe_of(pdev);
+ if (r)
+ return r;
} else {
return -ENODEV;
}
@@ -1320,12 +1369,20 @@ static int __exit dsicm_remove(struct platform_device *pdev)
return 0;
}
+static const struct of_device_id dsicm_of_match[] = {
+ { .compatible = "omapdss,panel-dsi-cm", },
+ {},
+};
+
+MODULE_DEVICE_TABLE(of, dsicm_of_match);
+
static struct platform_driver dsicm_driver = {
.probe = dsicm_probe,
.remove = __exit_p(dsicm_remove),
.driver = {
.name = "panel-dsi-cm",
.owner = THIS_MODULE,
+ .of_match_table = dsicm_of_match,
},
};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 13/41] OMAPDSS: Add DT support to DSI
From: Tomi Valkeinen @ 2014-01-21 10:56 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add the code to make the DSI driver work with device tree on OMAP3 and
OMAP4.
A minor hack is needed at the moment in the DSI driver: the DSS driver
needs to know the ID number of a DSI device, as clocks are routed in
different ways to the DSI devices. At the moment we don't have any
proper way to manage this, so this patchs adds a simple lookup table
that is used to deduce the ID from the DSI device's base address.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
drivers/video/omap2/dss/dsi.c | 139 +++++++++++++++++++++++++++++++++++++++++-
1 file changed, 138 insertions(+), 1 deletion(-)
diff --git a/drivers/video/omap2/dss/dsi.c b/drivers/video/omap2/dss/dsi.c
index b7c92705fb54..98bb2d68a462 100644
--- a/drivers/video/omap2/dss/dsi.c
+++ b/drivers/video/omap2/dss/dsi.c
@@ -38,6 +38,8 @@
#include <linux/slab.h>
#include <linux/debugfs.h>
#include <linux/pm_runtime.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
#include <video/omapdss.h>
#include <video/mipi_display.h>
@@ -386,6 +388,13 @@ struct dsi_packet_sent_handler_data {
struct completion *completion;
};
+struct dsi_module_id_data {
+ u32 address;
+ int id;
+};
+
+static const struct of_device_id dsi_of_match[];
+
#ifdef DSI_PERF_MEASURE
static bool dsi_perf;
module_param(dsi_perf, bool, 0644);
@@ -5373,12 +5382,69 @@ static void dsi_uninit_output(struct platform_device *dsidev)
omapdss_unregister_output(out);
}
+static int dsi_probe_of(struct platform_device *pdev)
+{
+ struct device_node *node = pdev->dev.of_node;
+ struct dsi_data *dsi = dsi_get_dsidrv_data(pdev);
+ struct property *prop;
+ u32 lane_arr[10];
+ int len, num_pins;
+ int r, i;
+ struct device_node *ep;
+ struct omap_dsi_pin_config pin_cfg;
+
+ ep = omapdss_of_get_first_endpoint(node);
+ if (!ep)
+ return 0;
+
+ prop = of_find_property(ep, "lanes", &len);
+ if (prop = NULL) {
+ dev_err(&pdev->dev, "failed to find lane data\n");
+ r = -EINVAL;
+ goto err;
+ }
+
+ num_pins = len / sizeof(u32);
+
+ if (num_pins < 4 || num_pins % 2 != 0
+ || num_pins > dsi->num_lanes_supported * 2) {
+ dev_err(&pdev->dev, "bad number of lanes\n");
+ r = -EINVAL;
+ goto err;
+ }
+
+ r = of_property_read_u32_array(ep, "lanes", lane_arr, num_pins);
+ if (r) {
+ dev_err(&pdev->dev, "failed to read lane data\n");
+ goto err;
+ }
+
+ pin_cfg.num_pins = num_pins;
+ for (i = 0; i < num_pins; ++i)
+ pin_cfg.pins[i] = (int)lane_arr[i];
+
+ r = dsi_configure_pins(&dsi->output, &pin_cfg);
+ if (r) {
+ dev_err(&pdev->dev, "failed to configure pins");
+ goto err;
+ }
+
+ of_node_put(ep);
+
+ return 0;
+
+err:
+ of_node_put(ep);
+ return r;
+}
+
/* DSI1 HW IP initialisation */
static int omap_dsihw_probe(struct platform_device *dsidev)
{
u32 rev;
int r, i;
struct dsi_data *dsi;
+ struct resource *dsi_mem;
struct resource *res;
struct resource temp_res;
@@ -5386,7 +5452,6 @@ static int omap_dsihw_probe(struct platform_device *dsidev)
if (!dsi)
return -ENOMEM;
- dsi->module_id = dsidev->id;
dsi->pdev = dsidev;
dev_set_drvdata(&dsidev->dev, dsi);
@@ -5424,6 +5489,8 @@ static int omap_dsihw_probe(struct platform_device *dsidev)
res = &temp_res;
}
+ dsi_mem = res;
+
dsi->proto_base = devm_ioremap(&dsidev->dev, res->start,
resource_size(res));
if (!dsi->proto_base) {
@@ -5484,6 +5551,31 @@ static int omap_dsihw_probe(struct platform_device *dsidev)
return r;
}
+ if (dsidev->dev.of_node) {
+ const struct of_device_id *match;
+ const struct dsi_module_id_data *d;
+
+ match = of_match_node(dsi_of_match, dsidev->dev.of_node);
+ if (!match) {
+ DSSERR("unsupported DSI module\n");
+ return -ENODEV;
+ }
+
+ d = match->data;
+
+ while (d->address != 0 && d->address != dsi_mem->start)
+ d++;
+
+ if (d->address = 0) {
+ DSSERR("unsupported DSI module\n");
+ return -ENODEV;
+ }
+
+ dsi->module_id = d->id;
+ } else {
+ dsi->module_id = dsidev->id;
+ }
+
/* DSI VCs initialization */
for (i = 0; i < ARRAY_SIZE(dsi->vc); i++) {
dsi->vc[i].source = DSI_VC_SOURCE_L4;
@@ -5519,6 +5611,19 @@ static int omap_dsihw_probe(struct platform_device *dsidev)
dsi_init_output(dsidev);
+ if (dsidev->dev.of_node) {
+ r = dsi_probe_of(dsidev);
+ if (r) {
+ DSSERR("Invalid DSI DT data\n");
+ goto err_probe_of;
+ }
+
+ r = of_platform_populate(dsidev->dev.of_node, NULL, NULL,
+ &dsidev->dev);
+ if (r)
+ DSSERR("Failed to populate DSI child devices: %d\n", r);
+ }
+
dsi_runtime_put(dsidev);
if (dsi->module_id = 0)
@@ -5532,17 +5637,31 @@ static int omap_dsihw_probe(struct platform_device *dsidev)
else if (dsi->module_id = 1)
dss_debugfs_create_file("dsi2_irqs", dsi2_dump_irqs);
#endif
+
return 0;
+err_probe_of:
+ dsi_uninit_output(dsidev);
+ dsi_runtime_put(dsidev);
+
err_runtime_get:
pm_runtime_disable(&dsidev->dev);
return r;
}
+static int dsi_unregister_child(struct device *dev, void *data)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ platform_device_unregister(pdev);
+ return 0;
+}
+
static int __exit omap_dsihw_remove(struct platform_device *dsidev)
{
struct dsi_data *dsi = dsi_get_dsidrv_data(dsidev);
+ device_for_each_child(&dsidev->dev, NULL, dsi_unregister_child);
+
WARN_ON(dsi->scp_clk_refcount > 0);
dsi_uninit_output(dsidev);
@@ -5580,6 +5699,23 @@ static const struct dev_pm_ops dsi_pm_ops = {
.runtime_resume = dsi_runtime_resume,
};
+static const struct dsi_module_id_data dsi_of_data_omap3[] = {
+ { .address = 0x4804fc00, .id = 0, },
+ { },
+};
+
+static const struct dsi_module_id_data dsi_of_data_omap4[] = {
+ { .address = 0x58004000, .id = 0, },
+ { .address = 0x58005000, .id = 1, },
+ { },
+};
+
+static const struct of_device_id dsi_of_match[] = {
+ { .compatible = "ti,omap3-dsi", .data = dsi_of_data_omap3, },
+ { .compatible = "ti,omap4-dsi", .data = dsi_of_data_omap4, },
+ {},
+};
+
static struct platform_driver omap_dsihw_driver = {
.probe = omap_dsihw_probe,
.remove = __exit_p(omap_dsihw_remove),
@@ -5587,6 +5723,7 @@ static struct platform_driver omap_dsihw_driver = {
.name = "omapdss_dsi",
.owner = THIS_MODULE,
.pm = &dsi_pm_ops,
+ .of_match_table = dsi_of_match,
},
};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 12/41] OMAPDSS: Add DT support to VENC
From: Tomi Valkeinen @ 2014-01-21 10:56 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT support to VENC.
In contrast to non-DT version, the DT version gets the invert-polarity
and connector type via venc's endpoint, not from the connector.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
drivers/video/omap2/dss/venc.c | 61 ++++++++++++++++++++++++++++++++++++++++++
1 file changed, 61 insertions(+)
diff --git a/drivers/video/omap2/dss/venc.c b/drivers/video/omap2/dss/venc.c
index c0e4def29795..b962a01961f5 100644
--- a/drivers/video/omap2/dss/venc.c
+++ b/drivers/video/omap2/dss/venc.c
@@ -34,6 +34,7 @@
#include <linux/platform_device.h>
#include <linux/regulator/consumer.h>
#include <linux/pm_runtime.h>
+#include <linux/of.h>
#include <video/omapdss.h>
@@ -808,6 +809,48 @@ static void __exit venc_uninit_output(struct platform_device *pdev)
omapdss_unregister_output(out);
}
+static int venc_probe_of(struct platform_device *pdev)
+{
+ struct device_node *node = pdev->dev.of_node;
+ struct device_node *ep;
+ u32 channels;
+ int r;
+
+ ep = omapdss_of_get_first_endpoint(node);
+ if (!ep)
+ return 0;
+
+ venc.invert_polarity = of_property_read_bool(ep, "ti,invert-polarity");
+
+ r = of_property_read_u32(ep, "ti,channels", &channels);
+ if (r) {
+ dev_err(&pdev->dev,
+ "failed to read property 'ti,channels': %d\n", r);
+ goto err;
+ }
+
+ switch (channels) {
+ case 1:
+ venc.type = OMAP_DSS_VENC_TYPE_COMPOSITE;
+ break;
+ case 2:
+ venc.type = OMAP_DSS_VENC_TYPE_SVIDEO;
+ break;
+ default:
+ dev_err(&pdev->dev, "bad channel propert '%d'\n", channels);
+ r = -EINVAL;
+ goto err;
+ }
+
+ of_node_put(ep);
+
+ return 0;
+err:
+ of_node_put(ep);
+
+ return 0;
+}
+
/* VENC HW IP initialisation */
static int omap_venchw_probe(struct platform_device *pdev)
{
@@ -849,12 +892,21 @@ static int omap_venchw_probe(struct platform_device *pdev)
venc_runtime_put();
+ if (pdev->dev.of_node) {
+ r = venc_probe_of(pdev);
+ if (r) {
+ DSSERR("Invalid DT data\n");
+ goto err_probe_of;
+ }
+ }
+
dss_debugfs_create_file("venc", venc_dump_regs);
venc_init_output(pdev);
return 0;
+err_probe_of:
err_runtime_get:
pm_runtime_disable(&pdev->dev);
return r;
@@ -898,6 +950,14 @@ static const struct dev_pm_ops venc_pm_ops = {
.runtime_resume = venc_runtime_resume,
};
+
+static const struct of_device_id venc_of_match[] = {
+ { .compatible = "ti,omap2-venc", },
+ { .compatible = "ti,omap3-venc", },
+ { .compatible = "ti,omap4-venc", },
+ {},
+};
+
static struct platform_driver omap_venchw_driver = {
.probe = omap_venchw_probe,
.remove = __exit_p(omap_venchw_remove),
@@ -905,6 +965,7 @@ static struct platform_driver omap_venchw_driver = {
.name = "omapdss_venc",
.owner = THIS_MODULE,
.pm = &venc_pm_ops,
+ .of_match_table = venc_of_match,
},
};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 11/41] OMAPDSS: Add DT support to HDMI
From: Tomi Valkeinen @ 2014-01-21 10:56 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT support to HDMI driver. The only thing needed for DT support here
is the of_match_table.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
drivers/video/omap2/dss/hdmi4.c | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/drivers/video/omap2/dss/hdmi4.c b/drivers/video/omap2/dss/hdmi4.c
index 11e7500197c1..064bec4e08d4 100644
--- a/drivers/video/omap2/dss/hdmi4.c
+++ b/drivers/video/omap2/dss/hdmi4.c
@@ -682,6 +682,11 @@ static const struct dev_pm_ops hdmi_pm_ops = {
.runtime_resume = hdmi_runtime_resume,
};
+static const struct of_device_id hdmi_of_match[] = {
+ { .compatible = "ti,omap4-hdmi", },
+ {},
+};
+
static struct platform_driver omapdss_hdmihw_driver = {
.probe = omapdss_hdmihw_probe,
.remove = __exit_p(omapdss_hdmihw_remove),
@@ -689,6 +694,7 @@ static struct platform_driver omapdss_hdmihw_driver = {
.name = "omapdss_hdmi",
.owner = THIS_MODULE,
.pm = &hdmi_pm_ops,
+ .of_match_table = hdmi_of_match,
},
};
--
1.8.3.2
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox