[PATCH v5 0/2] Lattice ECP5 FPGA manager

[PATCH v5 0/2] Lattice ECP5 FPGA manager

[Ivan Bornyakov]

Add support to the FPGA manager for programming Lattice ECP5 FPGA over
slave SPI interface with .bit formatted uncompressed bitstream image.

ChangeLog:
  v1 -> v2:
    * remove "spi" from compatible string
    * reword description in dt-bindings doc
    * add reference to spi-peripheral-props.yaml in dt-binding doc
    * fix DTS example in dt-bindings doc: 4-spaces indentations, no
      undersores in node names.
  v2 -> v3:
    * fix typo "##size-cells" -> "#size-cells" in dt-bindings example
  v3 -> v4:
    * dt-bindings: reword description
    * dt-bindings: revert props order
  v4 -> v5:
    * dt-bindings: remove trailing dot from title
    * dt-bindings: reword description to avoid driver reference
    * dt-bindings: add "Reviewed-by: Krzysztof Kozlowski" tag

Ivan Bornyakov (2):
  fpga: ecp5-spi: add Lattice ECP5 FPGA manager
  dt-bindings: fpga: add binding doc for ecp5-spi fpga mgr

 .../bindings/fpga/lattice,ecp5-fpga-mgr.yaml  |  74 +++++
 drivers/fpga/Kconfig                          |   7 +
 drivers/fpga/Makefile                         |   1 +
 drivers/fpga/ecp5-spi.c                       | 275 ++++++++++++++++++
 4 files changed, 357 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/fpga/lattice,ecp5-fpga-mgr.yaml
 create mode 100644 drivers/fpga/ecp5-spi.c

-- 
2.37.1

[PATCH v5 1/2] fpga: ecp5-spi: add Lattice ECP5 FPGA manager

[Ivan Bornyakov]

Add support to the FPGA manager for programming Lattice ECP5 FPGA over
slave SPI interface with .bit formatted uncompressed bitstream image.

Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
---
 drivers/fpga/Kconfig    |   7 +
 drivers/fpga/Makefile   |   1 +
 drivers/fpga/ecp5-spi.c | 275 ++++++++++++++++++++++++++++++++++++++++
 3 files changed, 283 insertions(+)
 create mode 100644 drivers/fpga/ecp5-spi.c

diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig
index 6c416955da53..920277a08ed9 100644
--- a/drivers/fpga/Kconfig
+++ b/drivers/fpga/Kconfig
@@ -263,4 +263,11 @@ config FPGA_MGR_MICROCHIP_SPI
 	  programming over slave SPI interface with .dat formatted
 	  bitstream image.
 
+config FPGA_MGR_ECP5_SPI
+	tristate "Lattice ECP5 SPI FPGA manager"
+	depends on SPI
+	help
+	  FPGA manager driver support for Lattice ECP5 programming over slave
+	  SPI interface with .bit formatted uncompressed bitstream image.
+
 endif # FPGA
diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile
index 42ae8b58abce..17c7a3c4b385 100644
--- a/drivers/fpga/Makefile
+++ b/drivers/fpga/Makefile
@@ -20,6 +20,7 @@ obj-$(CONFIG_FPGA_MGR_ZYNQ_FPGA)	+= zynq-fpga.o
 obj-$(CONFIG_FPGA_MGR_ZYNQMP_FPGA)	+= zynqmp-fpga.o
 obj-$(CONFIG_FPGA_MGR_VERSAL_FPGA)	+= versal-fpga.o
 obj-$(CONFIG_FPGA_MGR_MICROCHIP_SPI)	+= microchip-spi.o
+obj-$(CONFIG_FPGA_MGR_ECP5_SPI)		+= ecp5-spi.o
 obj-$(CONFIG_ALTERA_PR_IP_CORE)		+= altera-pr-ip-core.o
 obj-$(CONFIG_ALTERA_PR_IP_CORE_PLAT)	+= altera-pr-ip-core-plat.o
 
diff --git a/drivers/fpga/ecp5-spi.c b/drivers/fpga/ecp5-spi.c
new file mode 100644
index 000000000000..7293f19931e0
--- /dev/null
+++ b/drivers/fpga/ecp5-spi.c
@@ -0,0 +1,275 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Lattice ECP5 FPGA programming over slave SPI interface.
+ */
+
+#include <linux/delay.h>
+#include <linux/fpga/fpga-mgr.h>
+#include <linux/spi/spi.h>
+
+#define	ECP5_SPI_MAX_SPEED_HZ		60000000
+
+#define	ECP5_SPI_ISC_ENABLE		{0xC6, 0x00, 0x00, 0x00}
+#define	ECP5_SPI_ISC_DISABLE		{0x26, 0x00, 0x00, 0x00}
+#define	ECP5_SPI_ISC_ERASE		{0x0E, 0x01, 0x00, 0x00}
+#define	ECP5_SPI_LSC_INIT_ADDR		{0x46, 0x00, 0x00, 0x00}
+#define	ECP5_SPI_LSC_BITSTREAM_BURST	{0x7a, 0x00, 0x00, 0x00}
+#define	ECP5_SPI_LSC_CHECK_BUSY		{0xF0, 0x00, 0x00, 0x00}
+
+#define ECP5_POLL_RETRIES		100000
+
+struct ecp5_priv {
+	struct gpio_desc *program;
+	struct gpio_desc *init;
+	struct gpio_desc *done;
+	struct spi_device *spi;
+};
+
+static enum fpga_mgr_states ecp5_ops_state(struct fpga_manager *mgr)
+{
+	struct ecp5_priv *priv = mgr->priv;
+
+	return gpiod_get_value(priv->done) ? FPGA_MGR_STATE_OPERATING :
+					     FPGA_MGR_STATE_UNKNOWN;
+}
+
+static int ecp5_poll_busy(struct spi_device *spi)
+{
+	const u8 lsc_check_busy[] = ECP5_SPI_LSC_CHECK_BUSY;
+	int ret, retries = ECP5_POLL_RETRIES;
+	struct spi_transfer xfers[2] = { 0 };
+	u8 busy;
+
+	xfers[0].tx_buf = lsc_check_busy;
+	xfers[0].len = sizeof(lsc_check_busy);
+	xfers[1].rx_buf = &busy;
+	xfers[1].len = sizeof(busy);
+
+	while (retries--) {
+		ret = spi_sync_transfer(spi, xfers, ARRAY_SIZE(xfers));
+		if (ret)
+			return ret;
+
+		if (!busy)
+			return 0;
+
+		usleep_range(50, 100);
+	}
+
+	return -EBUSY;
+}
+
+static int ecp5_poll_gpio(struct gpio_desc *gpio, bool is_active)
+{
+	int value, retries = ECP5_POLL_RETRIES;
+
+	while (retries--) {
+		value = gpiod_get_value(gpio);
+		if (value < 0)
+			return value;
+
+		if ((!is_active && !value) || (is_active && value))
+			return 0;
+
+		ndelay(10);
+	}
+
+	return -EFAULT;
+}
+
+static int ecp5_ops_write_init(struct fpga_manager *mgr,
+			       struct fpga_image_info *info,
+			       const char *buf, size_t count)
+{
+	const u8 lsc_bitstream_burst[] = ECP5_SPI_LSC_BITSTREAM_BURST;
+	const u8 lsc_init_addr[] = ECP5_SPI_LSC_INIT_ADDR;
+	const u8 isc_enable[] = ECP5_SPI_ISC_ENABLE;
+	const u8 isc_erase[] = ECP5_SPI_ISC_ERASE;
+	struct ecp5_priv *priv = mgr->priv;
+	struct spi_device *spi = priv->spi;
+	struct device *dev = &mgr->dev;
+	struct spi_transfer isc_xfers[] = {
+		{
+			.tx_buf = isc_enable,
+			.len = sizeof(isc_enable),
+			.cs_change = 1,
+		}, {
+			.tx_buf = isc_erase,
+			.len = sizeof(isc_erase),
+		},
+	};
+	struct spi_transfer lsc_xfers[] = {
+		{
+			.tx_buf = lsc_init_addr,
+			.len = sizeof(lsc_init_addr),
+			.cs_change = 1,
+		}, {
+			.tx_buf = lsc_bitstream_burst,
+			.len = sizeof(lsc_bitstream_burst),
+			.cs_change = 1,
+		},
+	};
+	int ret;
+
+	if (info->flags & FPGA_MGR_PARTIAL_RECONFIG) {
+		dev_err(dev, "Partial reconfiguration is not supported\n");
+		return -EOPNOTSUPP;
+	}
+
+	/* Enter init mode */
+	gpiod_set_value(priv->program, 1);
+
+	ret = ecp5_poll_gpio(priv->init, true);
+	if (!ret)
+		ret = ecp5_poll_gpio(priv->done, false);
+
+	if (ret) {
+		dev_err(dev, "Failed to go to initialization mode\n");
+		return ret;
+	}
+
+	/* Enter program mode */
+	gpiod_set_value(priv->program, 0);
+
+	ret = ecp5_poll_gpio(priv->init, false);
+	if (ret) {
+		dev_err(dev, "Failed to go to program mode\n");
+		return ret;
+	}
+
+	/* Enter ISC mode */
+	ret = spi_sync_transfer(spi, isc_xfers, ARRAY_SIZE(isc_xfers));
+	if (!ret)
+		ret = ecp5_poll_busy(spi);
+
+	if (ret) {
+		dev_err(dev, "Failed to go to ISC mode\n");
+		return ret;
+	}
+
+	/* Prepare for bitstream burst write */
+	return spi_sync_transfer(spi, lsc_xfers, ARRAY_SIZE(lsc_xfers));
+}
+
+static int ecp5_ops_write(struct fpga_manager *mgr, const char *buf, size_t count)
+{
+	struct ecp5_priv *priv = mgr->priv;
+	struct spi_transfer xfer = {
+		.tx_buf = buf,
+		.len = count,
+		.cs_change = 1,
+	};
+
+	return spi_sync_transfer(priv->spi, &xfer, 1);
+}
+
+static int ecp5_ops_write_complete(struct fpga_manager *mgr,
+				   struct fpga_image_info *info)
+{
+	const u8 isc_disable[] = ECP5_SPI_ISC_DISABLE;
+	struct ecp5_priv *priv = mgr->priv;
+	struct spi_device *spi = priv->spi;
+	struct device *dev = &mgr->dev;
+	int ret;
+
+	/* Toggle CS and wait for bitstream write to finish */
+	ret = spi_write(spi, NULL, 0);
+	if (!ret)
+		ret = ecp5_poll_busy(spi);
+
+	if (ret) {
+		dev_err(dev, "Error while waiting bitstream write to finish\n");
+		return ret;
+	}
+
+	/* Exit ISC mode */
+	ret = spi_write(spi, isc_disable, sizeof(isc_disable));
+	if (!ret)
+		ret = ecp5_poll_gpio(priv->done, true);
+
+	if (ret)
+		dev_err(dev, "Failed to finish ISC\n");
+
+	return ret;
+}
+
+static const struct fpga_manager_ops ecp5_fpga_ops = {
+	.state = ecp5_ops_state,
+	.write_init = ecp5_ops_write_init,
+	.write = ecp5_ops_write,
+	.write_complete = ecp5_ops_write_complete,
+};
+
+static int ecp5_probe(struct spi_device *spi)
+{
+	struct device *dev = &spi->dev;
+	struct fpga_manager *mgr;
+	struct ecp5_priv *priv;
+	int ret;
+
+	if (spi->max_speed_hz > ECP5_SPI_MAX_SPEED_HZ) {
+		dev_err(dev, "SPI speed %u is too high, maximum speed is %u\n",
+			spi->max_speed_hz, ECP5_SPI_MAX_SPEED_HZ);
+		return -EINVAL;
+	}
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->spi = spi;
+
+	priv->done = devm_gpiod_get(dev, "done", GPIOD_IN);
+	if (IS_ERR(priv->done)) {
+		ret = PTR_ERR(priv->done);
+		dev_err(dev, "Failed to get DONE GPIO: %d\n", ret);
+		return ret;
+	}
+
+	priv->init = devm_gpiod_get(dev, "init", GPIOD_IN);
+	if (IS_ERR(priv->init)) {
+		ret = PTR_ERR(priv->init);
+		dev_err(dev, "Failed to get INIT GPIO: %d\n", ret);
+		return ret;
+	}
+
+	priv->program = devm_gpiod_get(dev, "program", GPIOD_OUT_LOW);
+	if (IS_ERR(priv->program)) {
+		ret = PTR_ERR(priv->program);
+		dev_err(dev, "Failed to get PROGRAM GPIO: %d\n", ret);
+		return ret;
+	}
+
+	mgr = devm_fpga_mgr_register(dev, "Lattice ECP5 SPI FPGA Manager",
+				     &ecp5_fpga_ops, priv);
+
+	return PTR_ERR_OR_ZERO(mgr);
+}
+
+static const struct spi_device_id ecp5_spi_ids[] = {
+	{ .name = "ecp5-fpga-mgr" },
+	{},
+};
+MODULE_DEVICE_TABLE(spi, ecp5_spi_ids);
+
+#if IS_ENABLED(CONFIG_OF)
+static const struct of_device_id ecp5_of_ids[] = {
+	{ .compatible = "lattice,ecp5-fpga-mgr" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, ecp5_of_ids);
+#endif /* IS_ENABLED(CONFIG_OF) */
+
+static struct spi_driver ecp5_driver = {
+	.probe = ecp5_probe,
+	.id_table = ecp5_spi_ids,
+	.driver = {
+		.name = "lattice_ecp5_spi_fpga_mgr",
+		.of_match_table = of_match_ptr(ecp5_of_ids),
+	},
+};
+
+module_spi_driver(ecp5_driver);
+
+MODULE_DESCRIPTION("Lattice ECP5 SPI FPGA Manager");
+MODULE_LICENSE("GPL");
-- 
2.37.1

Re: [PATCH v5 1/2] fpga: ecp5-spi: add Lattice ECP5 FPGA manager

[Daniel Glöckner]

Hi,

On Tue, Jul 19, 2022 at 02:23:34PM +0300, Ivan Bornyakov wrote:
> +	struct spi_transfer lsc_xfers[] = {
> +		{
> +			.tx_buf = lsc_init_addr,
> +			.len = sizeof(lsc_init_addr),
> +			.cs_change = 1,
> +		}, {
> +			.tx_buf = lsc_bitstream_burst,
> +			.len = sizeof(lsc_bitstream_burst),
> +			.cs_change = 1,
> +		},
> +	};

cs_change in the last transfer of a message will not prevent transfers
with other spi devices on the bus from taking place. You want to use
spi_bus_lock and friends in addition.

Best regards,

  Daniel

Re: [PATCH v5 1/2] fpga: ecp5-spi: add Lattice ECP5 FPGA manager

[Daniel Glöckner]

Hi,

On Tue, Jul 19, 2022 at 02:23:34PM +0300, Ivan Bornyakov wrote:
> +	/* Enter init mode */
> +	gpiod_set_value(priv->program, 1);
> +
> +	ret = ecp5_poll_gpio(priv->init, true);
> +	if (!ret)
> +		ret = ecp5_poll_gpio(priv->done, false);
> +
> +	if (ret) {
> +		dev_err(dev, "Failed to go to initialization mode\n");
> +		return ret;
> +	}

To me the documentation looks like the chip will deassert INITN after
tINITL regardless of the PROGRAMN signal. At 55ns max tINITL is too
short to reliably sample INITN while it is asserted when we have
interrupts enabled. Can you confirm that INITN stays asserted as long
as PROGRAMN is asserted?

Best regards,

  Daniel

Re: [PATCH v5 1/2] fpga: ecp5-spi: add Lattice ECP5 FPGA manager

[Ivan Bornyakov]

On Mon, Aug 01, 2022 at 09:24:49AM +0200, Daniel Glöckner wrote:
> Hi,
> 
> On Tue, Jul 19, 2022 at 02:23:34PM +0300, Ivan Bornyakov wrote:
> > +	/* Enter init mode */
> > +	gpiod_set_value(priv->program, 1);
> > +
> > +	ret = ecp5_poll_gpio(priv->init, true);
> > +	if (!ret)
> > +		ret = ecp5_poll_gpio(priv->done, false);
> > +
> > +	if (ret) {
> > +		dev_err(dev, "Failed to go to initialization mode\n");
> > +		return ret;
> > +	}
> 
> To me the documentation looks like the chip will deassert INITN after
> tINITL regardless of the PROGRAMN signal. At 55ns max tINITL is too
> short to reliably sample INITN while it is asserted when we have
> interrupts enabled. Can you confirm that INITN stays asserted as long
> as PROGRAMN is asserted?

I confirm that INITN stays asserted while PROGRAMN is asserted, just
rechecked.

[PATCH v5 2/2] dt-bindings: fpga: add binding doc for ecp5-spi fpga mgr

[Ivan Bornyakov]

Add Device Tree Binding doc for Lattice ECP5 FPGA manager using slave
SPI to load .bit formatted uncompressed bitstream image.

Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../bindings/fpga/lattice,ecp5-fpga-mgr.yaml  | 74 +++++++++++++++++++
 1 file changed, 74 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/fpga/lattice,ecp5-fpga-mgr.yaml

diff --git a/Documentation/devicetree/bindings/fpga/lattice,ecp5-fpga-mgr.yaml b/Documentation/devicetree/bindings/fpga/lattice,ecp5-fpga-mgr.yaml
new file mode 100644
index 000000000000..34693a3c2f1e
--- /dev/null
+++ b/Documentation/devicetree/bindings/fpga/lattice,ecp5-fpga-mgr.yaml
@@ -0,0 +1,74 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/fpga/lattice,ecp5-fpga-mgr.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Lattice ECP5 Slave SPI FPGA manager
+
+maintainers:
+  - Ivan Bornyakov <i.bornyakov@metrotek.ru>
+
+description:
+  Lattice ECP5 sysCONFIG port, which is used for device configuration, among
+  others, have Slave Serial Peripheral Interface. Only full reconfiguration
+  with uncompressed bitstream image in .bit format is supported.
+
+allOf:
+  - $ref: /schemas/spi/spi-peripheral-props.yaml
+
+properties:
+  compatible:
+    enum:
+      - lattice,ecp5-fpga-mgr
+
+  reg:
+    maxItems: 1
+
+  spi-max-frequency:
+    maximum: 60000000
+
+  program-gpios:
+    description:
+      A GPIO line connected to PROGRAMN (active low) pin of the device.
+      Initiates configuration sequence.
+    maxItems: 1
+
+  init-gpios:
+    description:
+      A GPIO line connected to INITN (active low) pin of the device.
+      Indicates that the FPGA is ready to be configured.
+    maxItems: 1
+
+  done-gpios:
+    description:
+      A GPIO line connected to DONE (active high) pin of the device.
+      Indicates that the configuration sequence is complete.
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - program-gpios
+  - init-gpios
+  - done-gpios
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    spi {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        fpga-mgr@0 {
+            compatible = "lattice,ecp5-fpga-mgr";
+            reg = <0>;
+            spi-max-frequency = <20000000>;
+            program-gpios = <&gpio3 4 GPIO_ACTIVE_LOW>;
+            init-gpios = <&gpio3 3 GPIO_ACTIVE_LOW>;
+            done-gpios = <&gpio3 2 GPIO_ACTIVE_HIGH>;
+        };
+    };
-- 
2.37.1

Re: [PATCH v5 2/2] dt-bindings: fpga: add binding doc for ecp5-spi fpga mgr

[Daniel Glöckner]

Hi,

On Tue, Jul 19, 2022 at 02:23:35PM +0300, Ivan Bornyakov wrote:
> +properties:
> +  compatible:
> +    enum:
> +      - lattice,ecp5-fpga-mgr

Since this driver uses the same interface as the existing
drivers/fpga/machxo2-spi.c driver, wouldn't it be advisable to use a
similar compatible id, i.e. lattice,ecp5-slave-spi?

> +required:
> +  - compatible
> +  - reg
> +  - program-gpios
> +  - init-gpios
> +  - done-gpios

I think some of the GPIOs can be made optional by reading the status
register or using the refresh command, assuming the slave spi interface
stayed enabled after previous programming and we are not dealing with
several chained FPGAs. But that can of course be left as an exercise for
other developers.

Best regards,

  Daniel

Re: [PATCH v5 2/2] dt-bindings: fpga: add binding doc for ecp5-spi fpga mgr

[Xu Yilun]

On Fri, Jul 29, 2022 at 11:01:24AM +0200, Daniel Glöckner wrote:
> Hi,
> 
> On Tue, Jul 19, 2022 at 02:23:35PM +0300, Ivan Bornyakov wrote:
> > +properties:
> > +  compatible:
> > +    enum:
> > +      - lattice,ecp5-fpga-mgr
> 
> Since this driver uses the same interface as the existing
> drivers/fpga/machxo2-spi.c driver, wouldn't it be advisable to use a
> similar compatible id, i.e. lattice,ecp5-slave-spi?

That's a good clue for me. I searched the machxo2 & ecp5 Programming
Usage Guide and seems they share the similar slave SPI sysCONFIG
interface, at least the command word tables are the same. So could we
have a generic driver for the lattice slave SPI sysCONFIG interface,
rather than create similar drivers for each board?

Thanks,
Yilun

> 
> > +required:
> > +  - compatible
> > +  - reg
> > +  - program-gpios
> > +  - init-gpios
> > +  - done-gpios
> 
> I think some of the GPIOs can be made optional by reading the status
> register or using the refresh command, assuming the slave spi interface
> stayed enabled after previous programming and we are not dealing with
> several chained FPGAs. But that can of course be left as an exercise for
> other developers.
> 
> Best regards,
> 
>   Daniel

Re: [PATCH v5 2/2] dt-bindings: fpga: add binding doc for ecp5-spi fpga mgr

[Ivan Bornyakov]

On Fri, Jul 29, 2022 at 11:01:24AM +0200, Daniel Glöckner wrote:
> Hi,
> 
> On Tue, Jul 19, 2022 at 02:23:35PM +0300, Ivan Bornyakov wrote:
> > +properties:
> > +  compatible:
> > +    enum:
> > +      - lattice,ecp5-fpga-mgr
> 
> Since this driver uses the same interface as the existing
> drivers/fpga/machxo2-spi.c driver, wouldn't it be advisable to use a
> similar compatible id, i.e. lattice,ecp5-slave-spi?
> 

To quote Krzysztof Kozlowski from v1 review:
 > Do not encode interface name in compatible so no "spi"

See https://lore.kernel.org/linux-fpga/044a9736-a4ec-c250-7755-c80a5bcbe38b@linaro.org/

> > +required:
> > +  - compatible
> > +  - reg
> > +  - program-gpios
> > +  - init-gpios
> > +  - done-gpios
> 
> I think some of the GPIOs can be made optional by reading the status
> register or using the refresh command, assuming the slave spi interface
> stayed enabled after previous programming and we are not dealing with
> several chained FPGAs. But that can of course be left as an exercise for
> other developers.

I would prefer the latter.

Re: [PATCH v5 2/2] dt-bindings: fpga: add binding doc for ecp5-spi fpga mgr

[Daniel Glöckner]

On Fri, Jul 29, 2022 at 07:33:47PM +0300, Ivan Bornyakov wrote:
> On Fri, Jul 29, 2022 at 11:01:24AM +0200, Daniel Glöckner wrote:
> > On Tue, Jul 19, 2022 at 02:23:35PM +0300, Ivan Bornyakov wrote:
> > > +properties:
> > > +  compatible:
> > > +    enum:
> > > +      - lattice,ecp5-fpga-mgr
> > 
> > Since this driver uses the same interface as the existing
> > drivers/fpga/machxo2-spi.c driver, wouldn't it be advisable to use a
> > similar compatible id, i.e. lattice,ecp5-slave-spi?
> > 
> 
> To quote Krzysztof Kozlowski from v1 review:
>  > Do not encode interface name in compatible so no "spi"
> 
> See https://lore.kernel.org/linux-fpga/044a9736-a4ec-c250-7755-c80a5bcbe38b@linaro.org/

true... MachXO2 to MachXO5 and those Nexus chips speak that protocol both
over spi and i2c and the position in the device tree decides which one it
should be. Maybe the compatible string in the existing driver should be
changed to lattice,machxo2. After all there is no other MachXO2-specific
interface/protocol except maybe jtag.

Best regards,

  Daniel

Re: [PATCH v5 0/2] Lattice ECP5 FPGA manager

[Xu Yilun]

On Tue, Jul 19, 2022 at 02:23:33PM +0300, Ivan Bornyakov wrote:
> Add support to the FPGA manager for programming Lattice ECP5 FPGA over
> slave SPI interface with .bit formatted uncompressed bitstream image.

I didn't have time to looking into the patches yet, but I have some quick
question.

Where is the bitstream data writing to? To the FPGA active region or the
backup nvmem like flash?

After reconfiguration, how to re-enumerate the hardware devices in the
newly programmed FPGA region?

Thanks,
Yilun

> 
> ChangeLog:
>   v1 -> v2:
>     * remove "spi" from compatible string
>     * reword description in dt-bindings doc
>     * add reference to spi-peripheral-props.yaml in dt-binding doc
>     * fix DTS example in dt-bindings doc: 4-spaces indentations, no
>       undersores in node names.
>   v2 -> v3:
>     * fix typo "##size-cells" -> "#size-cells" in dt-bindings example
>   v3 -> v4:
>     * dt-bindings: reword description
>     * dt-bindings: revert props order
>   v4 -> v5:
>     * dt-bindings: remove trailing dot from title
>     * dt-bindings: reword description to avoid driver reference
>     * dt-bindings: add "Reviewed-by: Krzysztof Kozlowski" tag
> 
> Ivan Bornyakov (2):
>   fpga: ecp5-spi: add Lattice ECP5 FPGA manager
>   dt-bindings: fpga: add binding doc for ecp5-spi fpga mgr
> 
>  .../bindings/fpga/lattice,ecp5-fpga-mgr.yaml  |  74 +++++
>  drivers/fpga/Kconfig                          |   7 +
>  drivers/fpga/Makefile                         |   1 +
>  drivers/fpga/ecp5-spi.c                       | 275 ++++++++++++++++++
>  4 files changed, 357 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/fpga/lattice,ecp5-fpga-mgr.yaml
>  create mode 100644 drivers/fpga/ecp5-spi.c
> 
> -- 
> 2.37.1
> 

Re: [PATCH v5 0/2] Lattice ECP5 FPGA manager

[Ivan Bornyakov]

On Thu, Jul 21, 2022 at 03:44:31PM +0800, Xu Yilun wrote:
> On Tue, Jul 19, 2022 at 02:23:33PM +0300, Ivan Bornyakov wrote:
> > Add support to the FPGA manager for programming Lattice ECP5 FPGA over
> > slave SPI interface with .bit formatted uncompressed bitstream image.
> 
> I didn't have time to looking into the patches yet, but I have some quick
> question.
> 
> Where is the bitstream data writing to? To the FPGA active region or the
> backup nvmem like flash?

Bitstream is written to FPGA's volatile SRAM configuration memory.

> 
> After reconfiguration, how to re-enumerate the hardware devices in the
> newly programmed FPGA region?
> 

I personally describe FPGA-based devices statically in DT overlay within
fpga-region. Of course this approach is error prone to mismatch between
firmware and devices described in DT overlay...

> Thanks,
> Yilun
> 
> > 
> > ChangeLog:
> >   v1 -> v2:
> >     * remove "spi" from compatible string
> >     * reword description in dt-bindings doc
> >     * add reference to spi-peripheral-props.yaml in dt-binding doc
> >     * fix DTS example in dt-bindings doc: 4-spaces indentations, no
> >       undersores in node names.
> >   v2 -> v3:
> >     * fix typo "##size-cells" -> "#size-cells" in dt-bindings example
> >   v3 -> v4:
> >     * dt-bindings: reword description
> >     * dt-bindings: revert props order
> >   v4 -> v5:
> >     * dt-bindings: remove trailing dot from title
> >     * dt-bindings: reword description to avoid driver reference
> >     * dt-bindings: add "Reviewed-by: Krzysztof Kozlowski" tag
> > 
> > Ivan Bornyakov (2):
> >   fpga: ecp5-spi: add Lattice ECP5 FPGA manager
> >   dt-bindings: fpga: add binding doc for ecp5-spi fpga mgr
> > 
> >  .../bindings/fpga/lattice,ecp5-fpga-mgr.yaml  |  74 +++++
> >  drivers/fpga/Kconfig                          |   7 +
> >  drivers/fpga/Makefile                         |   1 +
> >  drivers/fpga/ecp5-spi.c                       | 275 ++++++++++++++++++
> >  4 files changed, 357 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/fpga/lattice,ecp5-fpga-mgr.yaml
> >  create mode 100644 drivers/fpga/ecp5-spi.c
> > 
> > -- 
> > 2.37.1
> > 

Re: [PATCH v5 0/2] Lattice ECP5 FPGA manager

[Ivan Bornyakov]

On Tue, Jul 19, 2022 at 02:23:33PM +0300, Ivan Bornyakov wrote:
> Add support to the FPGA manager for programming Lattice ECP5 FPGA over
> slave SPI interface with .bit formatted uncompressed bitstream image.
> 
> ChangeLog:
>   v1 -> v2:
>     * remove "spi" from compatible string
>     * reword description in dt-bindings doc
>     * add reference to spi-peripheral-props.yaml in dt-binding doc
>     * fix DTS example in dt-bindings doc: 4-spaces indentations, no
>       undersores in node names.
>   v2 -> v3:
>     * fix typo "##size-cells" -> "#size-cells" in dt-bindings example
>   v3 -> v4:
>     * dt-bindings: reword description
>     * dt-bindings: revert props order
>   v4 -> v5:
>     * dt-bindings: remove trailing dot from title
>     * dt-bindings: reword description to avoid driver reference
>     * dt-bindings: add "Reviewed-by: Krzysztof Kozlowski" tag
> 
> Ivan Bornyakov (2):
>   fpga: ecp5-spi: add Lattice ECP5 FPGA manager
>   dt-bindings: fpga: add binding doc for ecp5-spi fpga mgr
> 
>  .../bindings/fpga/lattice,ecp5-fpga-mgr.yaml  |  74 +++++
>  drivers/fpga/Kconfig                          |   7 +
>  drivers/fpga/Makefile                         |   1 +
>  drivers/fpga/ecp5-spi.c                       | 275 ++++++++++++++++++
>  4 files changed, 357 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/fpga/lattice,ecp5-fpga-mgr.yaml
>  create mode 100644 drivers/fpga/ecp5-spi.c
> 
> -- 
> 2.37.1
> 

Friendly ping.