Linux filesystem development
 help / color / mirror / Atom feed
From: Breno Leitao <leitao@debian.org>
To: Oleg Nesterov <oleg@redhat.com>
Cc: Josh Triplett <josh@joshtriplett.org>,
	 Alexander Viro <viro@zeniv.linux.org.uk>,
	Christian Brauner <brauner@kernel.org>, Jan Kara <jack@suse.cz>,
	 Shuah Khan <shuah@kernel.org>, Mateusz Guzik <mjguzik@gmail.com>,
	linux-fsdevel@vger.kernel.org,  linux-kernel@vger.kernel.org,
	linux-kselftest@vger.kernel.org, shakeel.butt@linux.dev,
	 jlayton@kernel.org, axboe@kernel.dk, kernel-team@meta.com
Subject: Re: [PATCH v3 0/2] fs/pipe: reduce pipe->mutex contention by pre-allocating outside the lock
Date: Wed, 17 Jun 2026 03:23:54 -0700	[thread overview]
Message-ID: <ajJ1Xi1p9UhQvILi@gmail.com> (raw)
In-Reply-To: <ajJgWBCFYwz9OIo3@redhat.com>

On Wed, Jun 17, 2026 at 10:52:40AM +0200, Oleg Nesterov wrote:
> On 06/16, Josh Triplett wrote:
> >
> > On Sun, May 24, 2026 at 07:44:57AM -0700, Breno Leitao wrote:
> > > This series pre-allocates pages outside pipe->mutex in
> > > anon_pipe_write(): for writes that span more than one full page, up
> > > to PIPE_PREALLOC_MAX (8) pages are allocated via a per-page
> > > alloc_page() loop before the mutex is taken. anon_pipe_get_page()
> > > then drains the prealloc array first, falls back to the per-pipe
> > > tmp_page[] cache, and only enters the allocator under the mutex for
> > > the leftover pages (writes larger than PIPE_PREALLOC_MAX, single-page
> > > writes that skip prealloc, or shortfalls when the prealloc loop
> > > fails). Leftover prealloc pages are recycled into tmp_page[] before
> > > unlock and any remainder is put_page()'d after unlock, keeping the
> > > allocator out of the critical section on both sides.
> > [...]
> > > I also vibe-coded a microbenchmark to validate the change. It sweeps
> > > writers x readers over {1,2,5} x {1,5,10} with 64KB writes against a
> > > 1 MB pipe and prints throughput + latency percentiles per config.
> >
> > How do the numbers compare with 1-byte writes/reads? (It's fine if
> > they're not *faster*, just want to make sure they don't get any
> > *worse*. This case comes up a lot with pipes used for synchronization or
> > event reporting, such as with make.)
> 
> Note the "for writes that span more than one full page" above. Pre-allocate
> does nothing if total_len <= PAGE_SIZE.

Exactly.


The pre-allocation only triggers for multi-page writes:

anon_pipe_get_page_prealloc() returns immediately when total_len <= PAGE_SIZE,
so a 1-byte (or any sub-page) write never enters the new path.

anon_pipe_get_page() then falls through to the existing tmp_page/alloc_page
logic exactly as before; the only added cost is one length check and a NULL
prealloc pop, both trivially predicted.

Measured it to _just be sure_, 1-byte ping-pong (perf bench sched pipe -s 1):

    baseline:  2.674 usecs/op
    patched:   2.710 usecs/op   (+1.3%, within run-to-run noise)

--breno

  reply	other threads:[~2026-06-17 10:24 UTC|newest]

Thread overview: 18+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-05-24 14:44 [PATCH v3 0/2] fs/pipe: reduce pipe->mutex contention by pre-allocating outside the lock Breno Leitao
2026-05-24 14:44 ` [PATCH v3 1/2] fs/pipe: pre-allocate pages outside pipe->mutex in anon_pipe_write Breno Leitao
2026-05-24 14:44 ` [PATCH v3 2/2] selftests/pipe: add pipe_bench microbenchmark Breno Leitao
2026-05-28 12:34 ` [PATCH v3 0/2] fs/pipe: reduce pipe->mutex contention by pre-allocating outside the lock Christian Brauner
2026-06-16 20:47 ` Josh Triplett
2026-06-17  8:52   ` Oleg Nesterov
2026-06-17 10:23     ` Breno Leitao [this message]
2026-06-17 11:59       ` Mateusz Guzik
2026-06-17 14:37         ` Oleg Nesterov
2026-06-17 14:47           ` Breno Leitao
2026-06-17 14:57             ` Mateusz Guzik
2026-06-17 15:26               ` Breno Leitao
2026-06-17 15:45             ` Oleg Nesterov
2026-06-17 14:51           ` Mateusz Guzik
2026-06-17 15:30             ` Oleg Nesterov
2026-06-17 16:04         ` Oleg Nesterov
2026-06-17 15:01       ` Mateusz Guzik
2026-06-17 17:39         ` Breno Leitao

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=ajJ1Xi1p9UhQvILi@gmail.com \
    --to=leitao@debian.org \
    --cc=axboe@kernel.dk \
    --cc=brauner@kernel.org \
    --cc=jack@suse.cz \
    --cc=jlayton@kernel.org \
    --cc=josh@joshtriplett.org \
    --cc=kernel-team@meta.com \
    --cc=linux-fsdevel@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-kselftest@vger.kernel.org \
    --cc=mjguzik@gmail.com \
    --cc=oleg@redhat.com \
    --cc=shakeel.butt@linux.dev \
    --cc=shuah@kernel.org \
    --cc=viro@zeniv.linux.org.uk \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox