[PATCH v5 0/7] Add support of IRQs to QUICC ENGINE GPIOs

[PATCH v5 0/7] Add support of IRQs to QUICC ENGINE GPIOs

[Christophe Leroy]

The QUICC Engine provides interrupts for a few I/O ports. This is
handled via a separate interrupt ID and managed via a triplet of
dedicated registers hosted by the SoC.

Implement an interrupt driver for those IRQs then add change
notification capability to the QUICC ENGINE GPIOs.

The number of GPIOs for which interrupts are supported depends on
the microcontroller:
- mpc8323 has 10 GPIOS supporting interrupts
- mpc8360 has 28 GPIOS supporting interrupts
- mpc8568 has 18 GPIOS supporting interrupts

Changes in v5:
- Replaced new DT property "fsl,qe-gpio-irq-mask" by a mask encoded
in the of_device_id table
- Converted QE QPIO DT bindings to DT schema

Changes in v4:
- Removed unused headers
- Using device_property_read_u32() instead of of_property_read_u32()

Changes in v3:
- Splited dt-bindings update out of patch "soc: fsl: qe: Add support of IRQ in QE GPIO"
- Reordered DTS node exemples iaw dts-coding-style.rst

Changes in v2:
- Fixed warning on PPC64 build (Patch 1)
- Using devm_kzalloc() instead of kzalloc (Patch 2)
- Stop using of-mm-gpiochip (New patch 3)
- Added fsl,qe-gpio-irq-mask propertie in DT binding doc (Patch 4)
- Fixed problems reported by 'make dt_binding_check' (Patch 5)

Christophe Leroy (7):
  soc: fsl: qe: Add an interrupt controller for QUICC Engine Ports
  soc: fsl: qe: Change GPIO driver to a proper platform driver
  soc: fsl: qe: Drop legacy-of-mm-gpiochip.h header from GPIO driver
  soc: fsl: qe: Add support of IRQ in QE GPIO
  dt-bindings: soc: fsl: qe: Add an interrupt controller for QUICC
    Engine Ports
  dt-bindings: soc: fsl: qe: Convert QE GPIO to DT schema
  dt-bindings: soc: fsl: qe: Add support of IRQ in QE GPIO

 .../fsl/cpm_qe/fsl,mpc8323-qe-pario-bank.yaml |  76 +++++++
 .../soc/fsl/cpm_qe/fsl,qe-ports-ic.yaml       |  58 +++++
 .../bindings/soc/fsl/cpm_qe/qe/par_io.txt     |  26 +--
 arch/powerpc/platforms/Kconfig                |   1 -
 drivers/soc/fsl/qe/Makefile                   |   2 +-
 drivers/soc/fsl/qe/gpio.c                     | 209 ++++++++++++------
 drivers/soc/fsl/qe/qe_ports_ic.c              | 156 +++++++++++++
 7 files changed, 438 insertions(+), 90 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,mpc8323-qe-pario-bank.yaml
 create mode 100644 Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe-ports-ic.yaml
 create mode 100644 drivers/soc/fsl/qe/qe_ports_ic.c

-- 
2.49.0

[PATCH v5 1/7] soc: fsl: qe: Add an interrupt controller for QUICC Engine Ports

[Christophe Leroy]

The QUICC Engine provides interrupts for a few I/O ports. This is
handled via a separate interrupt ID and managed via a triplet of
dedicated registers hosted by the SoC.

Implement an interrupt driver for it for that those IRQs can then
be linked to the related GPIOs.

The number of ports for which interrupts are supported depends on
the microcontroller:
- mpc8323 has 10 interrupts
- mpc8360 has 28 interrupts
- mpc8568 has 18 interrupts
So add this information as data of the compatible.

Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
---
 drivers/soc/fsl/qe/Makefile      |   2 +-
 drivers/soc/fsl/qe/qe_ports_ic.c | 156 +++++++++++++++++++++++++++++++
 2 files changed, 157 insertions(+), 1 deletion(-)
 create mode 100644 drivers/soc/fsl/qe/qe_ports_ic.c

diff --git a/drivers/soc/fsl/qe/Makefile b/drivers/soc/fsl/qe/Makefile
index ec8506e13113..901a9c40d5eb 100644
--- a/drivers/soc/fsl/qe/Makefile
+++ b/drivers/soc/fsl/qe/Makefile
@@ -11,4 +11,4 @@ obj-$(CONFIG_UCC_SLOW)	+= ucc_slow.o
 obj-$(CONFIG_UCC_FAST)	+= ucc_fast.o
 obj-$(CONFIG_QE_TDM)	+= qe_tdm.o
 obj-$(CONFIG_QE_USB)	+= usb.o
-obj-$(CONFIG_QE_GPIO)	+= gpio.o
+obj-$(CONFIG_QE_GPIO)	+= gpio.o qe_ports_ic.o
diff --git a/drivers/soc/fsl/qe/qe_ports_ic.c b/drivers/soc/fsl/qe/qe_ports_ic.c
new file mode 100644
index 000000000000..9715643d36a6
--- /dev/null
+++ b/drivers/soc/fsl/qe/qe_ports_ic.c
@@ -0,0 +1,156 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * QUICC ENGINE I/O Ports Interrupt Controller
+ *
+ * Copyright (c) 2025 Christophe Leroy CS GROUP France (christophe.leroy@csgroup.eu)
+ */
+
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/platform_device.h>
+
+/* QE IC registers offset */
+#define CEPIER		0x0c
+#define CEPIMR		0x10
+#define CEPICR		0x14
+
+struct qepic_data {
+	void __iomem *reg;
+	struct irq_domain *host;
+};
+
+static void qepic_mask(struct irq_data *d)
+{
+	struct qepic_data *data = irq_data_get_irq_chip_data(d);
+
+	clrbits32(data->reg + CEPIMR, 1 << (31 - irqd_to_hwirq(d)));
+}
+
+static void qepic_unmask(struct irq_data *d)
+{
+	struct qepic_data *data = irq_data_get_irq_chip_data(d);
+
+	setbits32(data->reg + CEPIMR, 1 << (31 - irqd_to_hwirq(d)));
+}
+
+static void qepic_end(struct irq_data *d)
+{
+	struct qepic_data *data = irq_data_get_irq_chip_data(d);
+
+	out_be32(data->reg + CEPIER, 1 << (31 - irqd_to_hwirq(d)));
+}
+
+static int qepic_set_type(struct irq_data *d, unsigned int flow_type)
+{
+	struct qepic_data *data = irq_data_get_irq_chip_data(d);
+	unsigned int vec = (unsigned int)irqd_to_hwirq(d);
+
+	switch (flow_type & IRQ_TYPE_SENSE_MASK) {
+	case IRQ_TYPE_EDGE_FALLING:
+		setbits32(data->reg + CEPICR, 1 << (31 - vec));
+		return 0;
+	case IRQ_TYPE_EDGE_BOTH:
+	case IRQ_TYPE_NONE:
+		clrbits32(data->reg + CEPICR, 1 << (31 - vec));
+		return 0;
+	}
+	return -EINVAL;
+}
+
+static struct irq_chip qepic = {
+	.name = "QEPIC",
+	.irq_mask = qepic_mask,
+	.irq_unmask = qepic_unmask,
+	.irq_eoi = qepic_end,
+	.irq_set_type = qepic_set_type,
+};
+
+static int qepic_get_irq(struct irq_desc *desc)
+{
+	struct qepic_data *data = irq_desc_get_handler_data(desc);
+	u32 event = in_be32(data->reg + CEPIER);
+
+	if (!event)
+		return -1;
+
+	return irq_find_mapping(data->host, 32 - ffs(event));
+}
+
+static void qepic_cascade(struct irq_desc *desc)
+{
+	generic_handle_irq(qepic_get_irq(desc));
+}
+
+static int qepic_host_map(struct irq_domain *h, unsigned int virq, irq_hw_number_t hw)
+{
+	irq_set_chip_data(virq, h->host_data);
+	irq_set_chip_and_handler(virq, &qepic, handle_fasteoi_irq);
+	return 0;
+}
+
+static const struct irq_domain_ops qepic_host_ops = {
+	.map = qepic_host_map,
+};
+
+static int qepic_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct qepic_data *data;
+	unsigned long nb;
+	int irq;
+
+	nb = (unsigned long)of_device_get_match_data(dev);
+	if (nb < 1 || nb > 32)
+		return -EINVAL;
+
+	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	data->reg = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(data->reg))
+		return PTR_ERR(data->reg);
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0)
+		return irq;
+
+	data->host = irq_domain_add_linear(dev->of_node, nb, &qepic_host_ops, data);
+	if (!data->host)
+		return -ENODEV;
+
+	irq_set_handler_data(irq, data);
+	irq_set_chained_handler(irq, qepic_cascade);
+
+	return 0;
+}
+
+static const struct of_device_id qepic_match[] = {
+	{
+		.compatible = "fsl,mpc8323-qe-ports-ic",
+		.data = (void *)10,
+	},
+	{
+		.compatible = "fsl,mpc8360-qe-ports-ic",
+		.data = (void *)28,
+	},
+	{
+		.compatible = "fsl,mpc8568-qe-ports-ic",
+		.data = (void *)18,
+	},
+	{},
+};
+
+static struct platform_driver qepic_driver = {
+	.driver	= {
+		.name		= "qe_ports_ic",
+		.of_match_table	= qepic_match,
+	},
+	.probe	= qepic_probe,
+};
+
+static int __init qepic_init(void)
+{
+	return platform_driver_register(&qepic_driver);
+}
+arch_initcall(qepic_init);
-- 
2.49.0

[PATCH v5 2/7] soc: fsl: qe: Change GPIO driver to a proper platform driver

[Christophe Leroy]

In order to be able to add interrupts to the GPIOs, first change the
QE GPIO driver to the proper platform driver in order to allow
initialisation to be done in the right order, otherwise the GPIOs
get added before the interrupts are registered.

Remove linux/of.h and linux/property.h which are unused.

And to improve readability and reduce risk of errors, add a macro to
transform a pin number into the mask that matches the associated bit
in registers.

Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
---
v5: Added the PIN_MASK() macro
---
 drivers/soc/fsl/qe/gpio.c | 98 +++++++++++++++++++++------------------
 1 file changed, 53 insertions(+), 45 deletions(-)

diff --git a/drivers/soc/fsl/qe/gpio.c b/drivers/soc/fsl/qe/gpio.c
index 8df1e8fa86a5..04b44fc2bb58 100644
--- a/drivers/soc/fsl/qe/gpio.c
+++ b/drivers/soc/fsl/qe/gpio.c
@@ -12,16 +12,17 @@
 #include <linux/spinlock.h>
 #include <linux/err.h>
 #include <linux/io.h>
-#include <linux/of.h>
 #include <linux/gpio/legacy-of-mm-gpiochip.h>
 #include <linux/gpio/consumer.h>
 #include <linux/gpio/driver.h>
 #include <linux/slab.h>
 #include <linux/export.h>
-#include <linux/property.h>
+#include <linux/platform_device.h>
 
 #include <soc/fsl/qe/qe.h>
 
+#define PIN_MASK(gpio) (1UL << (QE_PIO_PINS - 1 - (gpio)))
+
 struct qe_gpio_chip {
 	struct of_mm_gpio_chip mm_gc;
 	spinlock_t lock;
@@ -52,7 +53,7 @@ static int qe_gpio_get(struct gpio_chip *gc, unsigned int gpio)
 {
 	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
 	struct qe_pio_regs __iomem *regs = mm_gc->regs;
-	u32 pin_mask = 1 << (QE_PIO_PINS - 1 - gpio);
+	u32 pin_mask = PIN_MASK(gpio);
 
 	return !!(ioread32be(&regs->cpdata) & pin_mask);
 }
@@ -63,7 +64,7 @@ static int qe_gpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
 	struct qe_gpio_chip *qe_gc = gpiochip_get_data(gc);
 	struct qe_pio_regs __iomem *regs = mm_gc->regs;
 	unsigned long flags;
-	u32 pin_mask = 1 << (QE_PIO_PINS - 1 - gpio);
+	u32 pin_mask = PIN_MASK(gpio);
 
 	spin_lock_irqsave(&qe_gc->lock, flags);
 
@@ -95,9 +96,9 @@ static int qe_gpio_set_multiple(struct gpio_chip *gc,
 			break;
 		if (__test_and_clear_bit(i, mask)) {
 			if (test_bit(i, bits))
-				qe_gc->cpdata |= (1U << (QE_PIO_PINS - 1 - i));
+				qe_gc->cpdata |= PIN_MASK(i);
 			else
-				qe_gc->cpdata &= ~(1U << (QE_PIO_PINS - 1 - i));
+				qe_gc->cpdata &= ~PIN_MASK(i);
 		}
 	}
 
@@ -295,45 +296,52 @@ void qe_pin_set_gpio(struct qe_pin *qe_pin)
 }
 EXPORT_SYMBOL(qe_pin_set_gpio);
 
-static int __init qe_add_gpiochips(void)
+static int qe_gpio_probe(struct platform_device *ofdev)
 {
-	struct device_node *np;
-
-	for_each_compatible_node(np, NULL, "fsl,mpc8323-qe-pario-bank") {
-		int ret;
-		struct qe_gpio_chip *qe_gc;
-		struct of_mm_gpio_chip *mm_gc;
-		struct gpio_chip *gc;
-
-		qe_gc = kzalloc(sizeof(*qe_gc), GFP_KERNEL);
-		if (!qe_gc) {
-			ret = -ENOMEM;
-			goto err;
-		}
+	struct device *dev = &ofdev->dev;
+	struct device_node *np = dev->of_node;
+	struct qe_gpio_chip *qe_gc;
+	struct of_mm_gpio_chip *mm_gc;
+	struct gpio_chip *gc;
 
-		spin_lock_init(&qe_gc->lock);
-
-		mm_gc = &qe_gc->mm_gc;
-		gc = &mm_gc->gc;
-
-		mm_gc->save_regs = qe_gpio_save_regs;
-		gc->ngpio = QE_PIO_PINS;
-		gc->direction_input = qe_gpio_dir_in;
-		gc->direction_output = qe_gpio_dir_out;
-		gc->get = qe_gpio_get;
-		gc->set = qe_gpio_set;
-		gc->set_multiple = qe_gpio_set_multiple;
-
-		ret = of_mm_gpiochip_add_data(np, mm_gc, qe_gc);
-		if (ret)
-			goto err;
-		continue;
-err:
-		pr_err("%pOF: registration failed with status %d\n",
-		       np, ret);
-		kfree(qe_gc);
-		/* try others anyway */
-	}
-	return 0;
+	qe_gc = devm_kzalloc(dev, sizeof(*qe_gc), GFP_KERNEL);
+	if (!qe_gc)
+		return -ENOMEM;
+
+	spin_lock_init(&qe_gc->lock);
+
+	mm_gc = &qe_gc->mm_gc;
+	gc = &mm_gc->gc;
+
+	mm_gc->save_regs = qe_gpio_save_regs;
+	gc->ngpio = QE_PIO_PINS;
+	gc->direction_input = qe_gpio_dir_in;
+	gc->direction_output = qe_gpio_dir_out;
+	gc->get = qe_gpio_get;
+	gc->set = qe_gpio_set;
+	gc->set_multiple = qe_gpio_set_multiple;
+
+	return of_mm_gpiochip_add_data(np, mm_gc, qe_gc);
+}
+
+static const struct of_device_id qe_gpio_match[] = {
+	{
+		.compatible = "fsl,mpc8323-qe-pario-bank",
+	},
+	{},
+};
+MODULE_DEVICE_TABLE(of, qe_gpio_match);
+
+static struct platform_driver qe_gpio_driver = {
+	.probe		= qe_gpio_probe,
+	.driver		= {
+		.name	= "qe-gpio",
+		.of_match_table	= qe_gpio_match,
+	},
+};
+
+static int __init qe_gpio_init(void)
+{
+	return platform_driver_register(&qe_gpio_driver);
 }
-arch_initcall(qe_add_gpiochips);
+arch_initcall(qe_gpio_init);
-- 
2.49.0

[PATCH v5 3/7] soc: fsl: qe: Drop legacy-of-mm-gpiochip.h header from GPIO driver

[Christophe Leroy]

Remove legacy-of-mm-gpiochip.h header file. The above mentioned
file provides an OF API that's deprecated. There is no agnostic
alternatives to it and we have to open code the logic which was
hidden behind of_mm_gpiochip_add_data(). Note, most of the GPIO
drivers are using their own labeling schemas and resource retrieval
that only a few may gain of the code deduplication, so whenever
alternative is appear we can move drivers again to use that one.

As a side effect this change fixes a potential memory leak on
an error path, if of_mm_gpiochip_add_data() fails.

[Text copied from commit 34064c8267a6 ("powerpc/8xx: Drop
legacy-of-mm-gpiochip.h header")]

Suggested-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
---
 arch/powerpc/platforms/Kconfig |  1 -
 drivers/soc/fsl/qe/gpio.c      | 51 ++++++++++++++++++----------------
 2 files changed, 27 insertions(+), 25 deletions(-)

diff --git a/arch/powerpc/platforms/Kconfig b/arch/powerpc/platforms/Kconfig
index fea3766eac0f..5b689bd3ddf4 100644
--- a/arch/powerpc/platforms/Kconfig
+++ b/arch/powerpc/platforms/Kconfig
@@ -232,7 +232,6 @@ config QE_GPIO
 	bool "QE GPIO support"
 	depends on QUICC_ENGINE
 	select GPIOLIB
-	select OF_GPIO_MM_GPIOCHIP
 	help
 	  Say Y here if you're going to use hardware that connects to the
 	  QE GPIOs.
diff --git a/drivers/soc/fsl/qe/gpio.c b/drivers/soc/fsl/qe/gpio.c
index 04b44fc2bb58..c54154b404df 100644
--- a/drivers/soc/fsl/qe/gpio.c
+++ b/drivers/soc/fsl/qe/gpio.c
@@ -12,7 +12,6 @@
 #include <linux/spinlock.h>
 #include <linux/err.h>
 #include <linux/io.h>
-#include <linux/gpio/legacy-of-mm-gpiochip.h>
 #include <linux/gpio/consumer.h>
 #include <linux/gpio/driver.h>
 #include <linux/slab.h>
@@ -24,7 +23,8 @@
 #define PIN_MASK(gpio) (1UL << (QE_PIO_PINS - 1 - (gpio)))
 
 struct qe_gpio_chip {
-	struct of_mm_gpio_chip mm_gc;
+	struct gpio_chip gc;
+	void __iomem *regs;
 	spinlock_t lock;
 
 	/* shadowed data register to clear/set bits safely */
@@ -34,11 +34,9 @@ struct qe_gpio_chip {
 	struct qe_pio_regs saved_regs;
 };
 
-static void qe_gpio_save_regs(struct of_mm_gpio_chip *mm_gc)
+static void qe_gpio_save_regs(struct qe_gpio_chip *qe_gc)
 {
-	struct qe_gpio_chip *qe_gc =
-		container_of(mm_gc, struct qe_gpio_chip, mm_gc);
-	struct qe_pio_regs __iomem *regs = mm_gc->regs;
+	struct qe_pio_regs __iomem *regs = qe_gc->regs;
 
 	qe_gc->cpdata = ioread32be(&regs->cpdata);
 	qe_gc->saved_regs.cpdata = qe_gc->cpdata;
@@ -51,8 +49,8 @@ static void qe_gpio_save_regs(struct of_mm_gpio_chip *mm_gc)
 
 static int qe_gpio_get(struct gpio_chip *gc, unsigned int gpio)
 {
-	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
-	struct qe_pio_regs __iomem *regs = mm_gc->regs;
+	struct qe_gpio_chip *qe_gc = gpiochip_get_data(gc);
+	struct qe_pio_regs __iomem *regs = qe_gc->regs;
 	u32 pin_mask = PIN_MASK(gpio);
 
 	return !!(ioread32be(&regs->cpdata) & pin_mask);
@@ -60,9 +58,8 @@ static int qe_gpio_get(struct gpio_chip *gc, unsigned int gpio)
 
 static int qe_gpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
 {
-	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
 	struct qe_gpio_chip *qe_gc = gpiochip_get_data(gc);
-	struct qe_pio_regs __iomem *regs = mm_gc->regs;
+	struct qe_pio_regs __iomem *regs = qe_gc->regs;
 	unsigned long flags;
 	u32 pin_mask = PIN_MASK(gpio);
 
@@ -83,9 +80,8 @@ static int qe_gpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
 static int qe_gpio_set_multiple(struct gpio_chip *gc,
 				unsigned long *mask, unsigned long *bits)
 {
-	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
 	struct qe_gpio_chip *qe_gc = gpiochip_get_data(gc);
-	struct qe_pio_regs __iomem *regs = mm_gc->regs;
+	struct qe_pio_regs __iomem *regs = qe_gc->regs;
 	unsigned long flags;
 	int i;
 
@@ -111,13 +107,12 @@ static int qe_gpio_set_multiple(struct gpio_chip *gc,
 
 static int qe_gpio_dir_in(struct gpio_chip *gc, unsigned int gpio)
 {
-	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
 	struct qe_gpio_chip *qe_gc = gpiochip_get_data(gc);
 	unsigned long flags;
 
 	spin_lock_irqsave(&qe_gc->lock, flags);
 
-	__par_io_config_pin(mm_gc->regs, gpio, QE_PIO_DIR_IN, 0, 0, 0);
+	__par_io_config_pin(qe_gc->regs, gpio, QE_PIO_DIR_IN, 0, 0, 0);
 
 	spin_unlock_irqrestore(&qe_gc->lock, flags);
 
@@ -126,7 +121,6 @@ static int qe_gpio_dir_in(struct gpio_chip *gc, unsigned int gpio)
 
 static int qe_gpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
 {
-	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
 	struct qe_gpio_chip *qe_gc = gpiochip_get_data(gc);
 	unsigned long flags;
 
@@ -134,7 +128,7 @@ static int qe_gpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
 
 	spin_lock_irqsave(&qe_gc->lock, flags);
 
-	__par_io_config_pin(mm_gc->regs, gpio, QE_PIO_DIR_OUT, 0, 0, 0);
+	__par_io_config_pin(qe_gc->regs, gpio, QE_PIO_DIR_OUT, 0, 0, 0);
 
 	spin_unlock_irqrestore(&qe_gc->lock, flags);
 
@@ -240,7 +234,7 @@ EXPORT_SYMBOL(qe_pin_free);
 void qe_pin_set_dedicated(struct qe_pin *qe_pin)
 {
 	struct qe_gpio_chip *qe_gc = qe_pin->controller;
-	struct qe_pio_regs __iomem *regs = qe_gc->mm_gc.regs;
+	struct qe_pio_regs __iomem *regs = qe_gc->regs;
 	struct qe_pio_regs *sregs = &qe_gc->saved_regs;
 	int pin = qe_pin->num;
 	u32 mask1 = 1 << (QE_PIO_PINS - (pin + 1));
@@ -269,7 +263,6 @@ void qe_pin_set_dedicated(struct qe_pin *qe_pin)
 
 	iowrite32be(qe_gc->cpdata, &regs->cpdata);
 	qe_clrsetbits_be32(&regs->cpodr, mask1, sregs->cpodr & mask1);
-
 	spin_unlock_irqrestore(&qe_gc->lock, flags);
 }
 EXPORT_SYMBOL(qe_pin_set_dedicated);
@@ -284,7 +277,7 @@ EXPORT_SYMBOL(qe_pin_set_dedicated);
 void qe_pin_set_gpio(struct qe_pin *qe_pin)
 {
 	struct qe_gpio_chip *qe_gc = qe_pin->controller;
-	struct qe_pio_regs __iomem *regs = qe_gc->mm_gc.regs;
+	struct qe_pio_regs __iomem *regs = qe_gc->regs;
 	unsigned long flags;
 
 	spin_lock_irqsave(&qe_gc->lock, flags);
@@ -301,7 +294,6 @@ static int qe_gpio_probe(struct platform_device *ofdev)
 	struct device *dev = &ofdev->dev;
 	struct device_node *np = dev->of_node;
 	struct qe_gpio_chip *qe_gc;
-	struct of_mm_gpio_chip *mm_gc;
 	struct gpio_chip *gc;
 
 	qe_gc = devm_kzalloc(dev, sizeof(*qe_gc), GFP_KERNEL);
@@ -310,18 +302,29 @@ static int qe_gpio_probe(struct platform_device *ofdev)
 
 	spin_lock_init(&qe_gc->lock);
 
-	mm_gc = &qe_gc->mm_gc;
-	gc = &mm_gc->gc;
+	gc = &qe_gc->gc;
 
-	mm_gc->save_regs = qe_gpio_save_regs;
+	gc->base = -1;
 	gc->ngpio = QE_PIO_PINS;
 	gc->direction_input = qe_gpio_dir_in;
 	gc->direction_output = qe_gpio_dir_out;
 	gc->get = qe_gpio_get;
 	gc->set = qe_gpio_set;
 	gc->set_multiple = qe_gpio_set_multiple;
+	gc->parent = dev;
+	gc->owner = THIS_MODULE;
+
+	gc->label = devm_kasprintf(dev, GFP_KERNEL, "%pOF", np);
+	if (!gc->label)
+		return -ENOMEM;
+
+	qe_gc->regs = devm_of_iomap(dev, np, 0, NULL);
+	if (IS_ERR(qe_gc->regs))
+		return PTR_ERR(qe_gc->regs);
+
+	qe_gpio_save_regs(qe_gc);
 
-	return of_mm_gpiochip_add_data(np, mm_gc, qe_gc);
+	return devm_gpiochip_add_data(dev, gc, qe_gc);
 }
 
 static const struct of_device_id qe_gpio_match[] = {
-- 
2.49.0

[PATCH v5 4/7] soc: fsl: qe: Add support of IRQ in QE GPIO

[Christophe Leroy]

In the QE, a few GPIOs have an associated IRQ to notify changes.
Add IRQ support to QE GPIO.

As not all GPIOs have an associated IRQ, the driver needs to know
to which GPIO corresponds each provided IRQ. This is provided via
multiple compatible properties:

	compatible = "fsl,mpc8323-qe-pario-bank-a"
	compatible = "fsl,mpc8323-qe-pario-bank-b"
	compatible = "fsl,mpc8323-qe-pario-bank-c"

	compatible = "fsl,mpc8360-qe-pario-bank-a"
	compatible = "fsl,mpc8360-qe-pario-bank-b"
	compatible = "fsl,mpc8360-qe-pario-bank-c"
	compatible = "fsl,mpc8360-qe-pario-bank-d"
	compatible = "fsl,mpc8360-qe-pario-bank-e"
	compatible = "fsl,mpc8360-qe-pario-bank-f"
	compatible = "fsl,mpc8360-qe-pario-bank-g"

	compatible = "fsl,mpc8568-qe-pario-bank-a"
	compatible = "fsl,mpc8568-qe-pario-bank-b"
	compatible = "fsl,mpc8568-qe-pario-bank-c"
	compatible = "fsl,mpc8568-qe-pario-bank-d"
	compatible = "fsl,mpc8568-qe-pario-bank-e"
	compatible = "fsl,mpc8568-qe-pario-bank-f"

When not using IRQ and for banks having no IRQ (like bank D on mpc8323)
the origin compatible = "fsl,mpc8323-qe-pario-bank" is sufficient.

Here is an exemple for port B of mpc8323 which has IRQs for
GPIOs PB7, PB9, PB25 and PB27.

	qe_pio_b: gpio-controller@1418 {
		compatible = "fsl,mpc8323-qe-pario-bank-b";
		reg = <0x1418 0x18>;
		interrupts = <4 5 6 7>;
		interrupt-parent = <&qepic>;
		gpio-controller;
		#gpio-cells = <2>;
	};

Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
---
v5: Provide the mask via the compatible data instead of adding a property in device tree
---
 drivers/soc/fsl/qe/gpio.c | 72 +++++++++++++++++++++++++++++++++++++++
 1 file changed, 72 insertions(+)

diff --git a/drivers/soc/fsl/qe/gpio.c b/drivers/soc/fsl/qe/gpio.c
index c54154b404df..8632b0d37255 100644
--- a/drivers/soc/fsl/qe/gpio.c
+++ b/drivers/soc/fsl/qe/gpio.c
@@ -12,6 +12,7 @@
 #include <linux/spinlock.h>
 #include <linux/err.h>
 #include <linux/io.h>
+#include <linux/of_irq.h>
 #include <linux/gpio/consumer.h>
 #include <linux/gpio/driver.h>
 #include <linux/slab.h>
@@ -32,6 +33,8 @@ struct qe_gpio_chip {
 
 	/* saved_regs used to restore dedicated functions */
 	struct qe_pio_regs saved_regs;
+
+	int irq[QE_PIO_PINS];
 };
 
 static void qe_gpio_save_regs(struct qe_gpio_chip *qe_gc)
@@ -135,6 +138,13 @@ static int qe_gpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
 	return 0;
 }
 
+static int qe_gpio_to_irq(struct gpio_chip *gc, unsigned int gpio)
+{
+	struct qe_gpio_chip *qe_gc = gpiochip_get_data(gc);
+
+	return qe_gc->irq[gpio] ? : -ENXIO;
+}
+
 struct qe_pin {
 	/*
 	 * The qe_gpio_chip name is unfortunate, we should change that to
@@ -295,6 +305,7 @@ static int qe_gpio_probe(struct platform_device *ofdev)
 	struct device_node *np = dev->of_node;
 	struct qe_gpio_chip *qe_gc;
 	struct gpio_chip *gc;
+	u32 mask;
 
 	qe_gc = devm_kzalloc(dev, sizeof(*qe_gc), GFP_KERNEL);
 	if (!qe_gc)
@@ -302,6 +313,15 @@ static int qe_gpio_probe(struct platform_device *ofdev)
 
 	spin_lock_init(&qe_gc->lock);
 
+	mask = (u32)of_device_get_match_data(dev);
+	if (mask) {
+		int i, j;
+
+		for (i = 0, j = 0; i < ARRAY_SIZE(qe_gc->irq); i++)
+			if (mask & PIN_MASK(i))
+				qe_gc->irq[i] = irq_of_parse_and_map(np, j++);
+	}
+
 	gc = &qe_gc->gc;
 
 	gc->base = -1;
@@ -311,6 +331,7 @@ static int qe_gpio_probe(struct platform_device *ofdev)
 	gc->get = qe_gpio_get;
 	gc->set = qe_gpio_set;
 	gc->set_multiple = qe_gpio_set_multiple;
+	gc->to_irq = qe_gpio_to_irq;
 	gc->parent = dev;
 	gc->owner = THIS_MODULE;
 
@@ -330,6 +351,57 @@ static int qe_gpio_probe(struct platform_device *ofdev)
 static const struct of_device_id qe_gpio_match[] = {
 	{
 		.compatible = "fsl,mpc8323-qe-pario-bank",
+	}, {
+		.compatible = "fsl,mpc8323-qe-pario-bank-a",
+		.data = (void *)(PIN_MASK(8) | PIN_MASK(10) | PIN_MASK(26) | PIN_MASK(28)),
+	}, {
+		.compatible = "fsl,mpc8323-qe-pario-bank-b",
+		.data = (void *)(PIN_MASK(7) | PIN_MASK(9) | PIN_MASK(25) | PIN_MASK(27)),
+	}, {
+		.compatible = "fsl,mpc8323-qe-pario-bank-c",
+		.data = (void *)(PIN_MASK(24) | PIN_MASK(29)),
+	}, {
+		.compatible = "fsl,mpc8360-qe-pario-bank-a",
+		.data = (void *)(PIN_MASK(15) | PIN_MASK(16) | PIN_MASK(29) | PIN_MASK(30)),
+	}, {
+		.compatible = "fsl,mpc8360-qe-pario-bank-b",
+		.data = (void *)(PIN_MASK(3) | PIN_MASK(5) | PIN_MASK(12) | PIN_MASK(13) |
+				 PIN_MASK(26) | PIN_MASK(27)),
+	}, {
+		.compatible = "fsl,mpc8360-qe-pario-bank-c",
+		.data = (void *)(PIN_MASK(27) | PIN_MASK(28) | PIN_MASK(29)),
+	}, {
+		.compatible = "fsl,mpc8360-qe-pario-bank-d",
+		.data = (void *)(PIN_MASK(12) | PIN_MASK(13) | PIN_MASK(16) | PIN_MASK(17) |
+				 PIN_MASK(26) | PIN_MASK(27)),
+	}, {
+		.compatible = "fsl,mpc8360-qe-pario-bank-e",
+		.data = (void *)(PIN_MASK(12) | PIN_MASK(13) | PIN_MASK(24) | PIN_MASK(25) |
+				 PIN_MASK(26) | PIN_MASK(27) | PIN_MASK(31)),
+	}, {
+		.compatible = "fsl,mpc8360-qe-pario-bank-f",
+		.data = (void *)(PIN_MASK(20)),
+	}, {
+		.compatible = "fsl,mpc8360-qe-pario-bank-g",
+		.data = (void *)(PIN_MASK(31)),
+	}, {
+		.compatible = "fsl,mpc8568-qe-pario-bank-a",
+		.data = (void *)(PIN_MASK(22) | PIN_MASK(23)),
+	}, {
+		.compatible = "fsl,mpc8568-qe-pario-bank-b",
+		.data = (void *)(PIN_MASK(12) | PIN_MASK(13) | PIN_MASK(28) | PIN_MASK(29)),
+	}, {
+		.compatible = "fsl,mpc8568-qe-pario-bank-c",
+		.data = (void *)(PIN_MASK(16) | PIN_MASK(17) | PIN_MASK(25) | PIN_MASK(26)),
+	}, {
+		.compatible = "fsl,mpc8568-qe-pario-bank-d",
+		.data = (void *)(PIN_MASK(18) | PIN_MASK(19)),
+	}, {
+		.compatible = "fsl,mpc8568-qe-pario-bank-e",
+		.data = (void *)(PIN_MASK(12) | PIN_MASK(16) | PIN_MASK(30)),
+	}, {
+		.compatible = "fsl,mpc8568-qe-pario-bank-f",
+		.data = (void *)(PIN_MASK(12) | PIN_MASK(16) | PIN_MASK(30)),
 	},
 	{},
 };
-- 
2.49.0

[PATCH v5 5/7] dt-bindings: soc: fsl: qe: Add an interrupt controller for QUICC Engine Ports

[Christophe Leroy]

The QUICC Engine provides interrupts for a few I/O ports. This is
handled via a separate interrupt ID and managed via a triplet of
dedicated registers hosted by the SoC.

Implement an interrupt driver for it for that those IRQs can then
be linked to the related GPIOs.

Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
---
 .../soc/fsl/cpm_qe/fsl,qe-ports-ic.yaml       | 58 +++++++++++++++++++
 1 file changed, 58 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe-ports-ic.yaml

diff --git a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe-ports-ic.yaml b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe-ports-ic.yaml
new file mode 100644
index 000000000000..a356ad8b13f5
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe-ports-ic.yaml
@@ -0,0 +1,58 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,qe-ports-ic.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale QUICC Engine I/O Ports Interrupt Controller
+
+maintainers:
+  - Christophe Leroy <christophe.leroy@csgroup.eu>
+
+description:
+  Interrupt controller for the QUICC Engine I/O ports found on some Freescale/NXP PowerQUICC and QorIQ SoCs.
+
+properties:
+  compatible:
+    enum:
+      - fsl,mpc8323-qe-ports-ic
+      - fsl,mpc8360-qe-ports-ic
+      - fsl,mpc8568-qe-ports-ic
+
+  reg:
+    maxItems: 1
+    description: Base address and size of the QE I/O Ports Interrupt Controller registers.
+
+  interrupt-controller: true
+
+  '#address-cells':
+    const: 0
+
+  '#interrupt-cells':
+    const: 1
+
+  interrupts:
+    maxItems: 1
+    description: Interrupt line to which the QE I/O Ports controller is connected.
+
+required:
+  - compatible
+  - reg
+  - interrupt-controller
+  - '#address-cells'
+  - '#interrupt-cells'
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    interrupt-controller@c00 {
+      compatible = "fsl,mpc8323-qe-ports-ic";
+      reg = <0xc00 0x18>;
+      interrupt-controller;
+      #address-cells = <0>;
+      #interrupt-cells = <1>;
+      interrupts = <74 0x8>;
+      interrupt-parent = <&ipic>;
+    };
-- 
2.49.0

[PATCH v5 6/7] dt-bindings: soc: fsl: qe: Convert QE GPIO to DT schema

[Christophe Leroy]

Convert QE QPIO devicetree binding to DT schema.

Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
---
v5: New
---
 .../fsl/cpm_qe/fsl,mpc8323-qe-pario-bank.yaml | 53 +++++++++++++++++++
 .../bindings/soc/fsl/cpm_qe/qe/par_io.txt     | 26 +--------
 2 files changed, 54 insertions(+), 25 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,mpc8323-qe-pario-bank.yaml

diff --git a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,mpc8323-qe-pario-bank.yaml b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,mpc8323-qe-pario-bank.yaml
new file mode 100644
index 000000000000..e6ba319a75c1
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,mpc8323-qe-pario-bank.yaml
@@ -0,0 +1,53 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,mpc8323-qe-pario-bank.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale QUICC Engine Parallel I/O (QE PARIO) GPIO Bank
+
+maintainers:
+  - Christophe Leroy <christophe.leroy@csgroup.eu>
+
+description:
+  Bindings for the Freescale QUICC Engine Parallel I/O (PARIO) GPIO controller.
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - fsl,chip-qe-pario-bank
+      - const: fsl,mpc8323-qe-pario-bank
+
+  reg:
+    maxItems: 1
+    description: Offset to the register set and its length.
+
+  gpio-controller: true
+
+  '#gpio-cells':
+    const: 2
+
+required:
+  - compatible
+  - reg
+  - gpio-controller
+  - '#gpio-cells'
+
+additionalProperties: false
+
+examples:
+  - |
+    qe_pio_a: gpio-controller@1400 {
+        compatible = "fsl,mpc8360-qe-pario-bank", "fsl,mpc8323-qe-pario-bank";
+        reg = <0x1400 0x18>;
+        gpio-controller;
+        #gpio-cells = <2>;
+    };
+
+    qe_pio_e: gpio-controller@1460 {
+        compatible = "fsl,mpc8360-qe-pario-bank", "fsl,mpc8323-qe-pario-bank";
+        reg = <0x1460 0x18>;
+        gpio-controller;
+        #gpio-cells = <2>;
+    };
diff --git a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe/par_io.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe/par_io.txt
index 09b1b05fa677..782699c14567 100644
--- a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe/par_io.txt
+++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe/par_io.txt
@@ -24,28 +24,4 @@ par_io@1400 {
 
 Note that "par_io" nodes are obsolete, and should not be used for
 the new device trees. Instead, each Par I/O bank should be represented
-via its own gpio-controller node:
-
-Required properties:
-- #gpio-cells : should be "2".
-- compatible : should be "fsl,<chip>-qe-pario-bank",
-  "fsl,mpc8323-qe-pario-bank".
-- reg : offset to the register set and its length.
-- gpio-controller : node to identify gpio controllers.
-
-Example:
-	qe_pio_a: gpio-controller@1400 {
-		#gpio-cells = <2>;
-		compatible = "fsl,mpc8360-qe-pario-bank",
-		"fsl,mpc8323-qe-pario-bank";
-		reg = <0x1400 0x18>;
-		gpio-controller;
-	  };
-
-	qe_pio_e: gpio-controller@1460 {
-		#gpio-cells = <2>;
-		compatible = "fsl,mpc8360-qe-pario-bank",
-			     "fsl,mpc8323-qe-pario-bank";
-		reg = <0x1460 0x18>;
-		gpio-controller;
-	  };
+via its own gpio-controller node.
-- 
2.49.0

[PATCH v5 7/7] dt-bindings: soc: fsl: qe: Add support of IRQ in QE GPIO

[Christophe Leroy]

In the QE, a few GPIOs have an associated IRQ to notify changes.
Add IRQ support to QE GPIO.

As not all GPIOs have an associated IRQ, the driver needs to know
to which GPIO corresponds each provided IRQ. This is provided via
multiple compatible properties:

	compatible = "fsl,mpc8323-qe-pario-bank-a"
	compatible = "fsl,mpc8323-qe-pario-bank-b"
	compatible = "fsl,mpc8323-qe-pario-bank-c"

	compatible = "fsl,mpc8360-qe-pario-bank-a"
	compatible = "fsl,mpc8360-qe-pario-bank-b"
	compatible = "fsl,mpc8360-qe-pario-bank-c"
	compatible = "fsl,mpc8360-qe-pario-bank-d"
	compatible = "fsl,mpc8360-qe-pario-bank-e"
	compatible = "fsl,mpc8360-qe-pario-bank-f"
	compatible = "fsl,mpc8360-qe-pario-bank-g"

	compatible = "fsl,mpc8568-qe-pario-bank-a"
	compatible = "fsl,mpc8568-qe-pario-bank-b"
	compatible = "fsl,mpc8568-qe-pario-bank-c"
	compatible = "fsl,mpc8568-qe-pario-bank-d"
	compatible = "fsl,mpc8568-qe-pario-bank-e"
	compatible = "fsl,mpc8568-qe-pario-bank-f"

When not using IRQ and for banks having no IRQ (like bank D on mpc8323)
the origin compatible = "fsl,mpc8323-qe-pario-bank" is still valid.

Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
---
v5: Changed to DT schema
---
 .../fsl/cpm_qe/fsl,mpc8323-qe-pario-bank.yaml | 27 +++++++++++++++++--
 1 file changed, 25 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,mpc8323-qe-pario-bank.yaml b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,mpc8323-qe-pario-bank.yaml
index e6ba319a75c1..80f93914c779 100644
--- a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,mpc8323-qe-pario-bank.yaml
+++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,mpc8323-qe-pario-bank.yaml
@@ -17,6 +17,22 @@ properties:
     items:
       - enum:
           - fsl,chip-qe-pario-bank
+          - fsl,mpc8323-qe-pario-bank-a
+          - fsl,mpc8323-qe-pario-bank-b
+          - fsl,mpc8323-qe-pario-bank-c
+          - fsl,mpc8360-qe-pario-bank-a
+          - fsl,mpc8360-qe-pario-bank-b
+          - fsl,mpc8360-qe-pario-bank-c
+          - fsl,mpc8360-qe-pario-bank-d
+          - fsl,mpc8360-qe-pario-bank-e
+          - fsl,mpc8360-qe-pario-bank-f
+          - fsl,mpc8360-qe-pario-bank-g
+          - fsl,mpc8568-qe-pario-bank-a
+          - fsl,mpc8568-qe-pario-bank-b
+          - fsl,mpc8568-qe-pario-bank-c
+          - fsl,mpc8568-qe-pario-bank-d
+          - fsl,mpc8568-qe-pario-bank-e
+          - fsl,mpc8568-qe-pario-bank-f
       - const: fsl,mpc8323-qe-pario-bank
 
   reg:
@@ -28,6 +44,9 @@ properties:
   '#gpio-cells':
     const: 2
 
+  interrupts:
+    description: List of interrupts for lines of the port that trigger interrupts on change.
+
 required:
   - compatible
   - reg
@@ -39,15 +58,19 @@ additionalProperties: false
 examples:
   - |
     qe_pio_a: gpio-controller@1400 {
-        compatible = "fsl,mpc8360-qe-pario-bank", "fsl,mpc8323-qe-pario-bank";
+        compatible = "fsl,mpc8360-qe-pario-bank-a", "fsl,mpc8323-qe-pario-bank";
         reg = <0x1400 0x18>;
         gpio-controller;
         #gpio-cells = <2>;
+        interrupts = <0 1 2 3>;
+        interrupt-parent = <&qepic>;
     };
 
     qe_pio_e: gpio-controller@1460 {
-        compatible = "fsl,mpc8360-qe-pario-bank", "fsl,mpc8323-qe-pario-bank";
+        compatible = "fsl,mpc8360-qe-pario-bank-e", "fsl,mpc8323-qe-pario-bank";
         reg = <0x1460 0x18>;
         gpio-controller;
         #gpio-cells = <2>;
+        interrupts = <19 20 21 22 23 24 25>;
+        interrupt-parent = <&qepic>;
     };
-- 
2.49.0

Re: [PATCH v5 3/7] soc: fsl: qe: Drop legacy-of-mm-gpiochip.h header from GPIO driver

[Bartosz Golaszewski]

On Mon, 1 Sep 2025 14:05:10 +0200, Christophe Leroy
<christophe.leroy@csgroup.eu> said:
> Remove legacy-of-mm-gpiochip.h header file. The above mentioned
> file provides an OF API that's deprecated. There is no agnostic
> alternatives to it and we have to open code the logic which was
> hidden behind of_mm_gpiochip_add_data(). Note, most of the GPIO
> drivers are using their own labeling schemas and resource retrieval
> that only a few may gain of the code deduplication, so whenever
> alternative is appear we can move drivers again to use that one.
>
> As a side effect this change fixes a potential memory leak on
> an error path, if of_mm_gpiochip_add_data() fails.
>
> [Text copied from commit 34064c8267a6 ("powerpc/8xx: Drop
> legacy-of-mm-gpiochip.h header")]
>
> Suggested-by: Bartosz Golaszewski <brgl@bgdev.pl>
> Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>

Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

Re: [PATCH v5 6/7] dt-bindings: soc: fsl: qe: Convert QE GPIO to DT schema

[Rob Herring]

On Mon, Sep 01, 2025 at 02:05:13PM +0200, Christophe Leroy wrote:
> Convert QE QPIO devicetree binding to DT schema.
> 
> Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
> ---
> v5: New
> ---
>  .../fsl/cpm_qe/fsl,mpc8323-qe-pario-bank.yaml | 53 +++++++++++++++++++

This should move to bindings/gpio/

>  .../bindings/soc/fsl/cpm_qe/qe/par_io.txt     | 26 +--------
>  2 files changed, 54 insertions(+), 25 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,mpc8323-qe-pario-bank.yaml
> 
> diff --git a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,mpc8323-qe-pario-bank.yaml b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,mpc8323-qe-pario-bank.yaml
> new file mode 100644
> index 000000000000..e6ba319a75c1
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,mpc8323-qe-pario-bank.yaml
> @@ -0,0 +1,53 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,mpc8323-qe-pario-bank.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Freescale QUICC Engine Parallel I/O (QE PARIO) GPIO Bank
> +
> +maintainers:
> +  - Christophe Leroy <christophe.leroy@csgroup.eu>
> +
> +description:
> +  Bindings for the Freescale QUICC Engine Parallel I/O (PARIO) GPIO controller.

Just drop if nothing more to say than 'title'.

> +
> +properties:
> +  compatible:
> +    items:
> +      - enum:
> +          - fsl,chip-qe-pario-bank
> +      - const: fsl,mpc8323-qe-pario-bank
> +
> +  reg:
> +    maxItems: 1
> +    description: Offset to the register set and its length.

Drop the description. That's every reg.

> +
> +  gpio-controller: true
> +
> +  '#gpio-cells':
> +    const: 2
> +
> +required:
> +  - compatible
> +  - reg
> +  - gpio-controller
> +  - '#gpio-cells'
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    qe_pio_a: gpio-controller@1400 {

Drop unused labels.

> +        compatible = "fsl,mpc8360-qe-pario-bank", "fsl,mpc8323-qe-pario-bank";

Doesn't match the schema. 

> +        reg = <0x1400 0x18>;
> +        gpio-controller;
> +        #gpio-cells = <2>;
> +    };
> +
> +    qe_pio_e: gpio-controller@1460 {
> +        compatible = "fsl,mpc8360-qe-pario-bank", "fsl,mpc8323-qe-pario-bank";
> +        reg = <0x1460 0x18>;
> +        gpio-controller;
> +        #gpio-cells = <2>;
> +    };

Re: [PATCH v5 6/7] dt-bindings: soc: fsl: qe: Convert QE GPIO to DT schema

[Christophe Leroy]

Hi Rob,

Le 02/09/2025 à 23:24, Rob Herring a écrit :
> On Mon, Sep 01, 2025 at 02:05:13PM +0200, Christophe Leroy wrote:
>> Convert QE QPIO devicetree binding to DT schema.
>>
>> Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
>> ---
>> v5: New
>> ---
> 
>> +
>> +properties:
>> +  compatible:
>> +    items:
>> +      - enum:
>> +          - fsl,chip-qe-pario-bank
>> +      - const: fsl,mpc8323-qe-pario-bank
>> +

snip

> 
>> +        compatible = "fsl,mpc8360-qe-pario-bank", "fsl,mpc8323-qe-pario-bank";
> 
> Doesn't match the schema.
> 

Can you be more explicit ? Is it the 'mpc8360' ? It is the 'chip'.


bindings/soc/fsl/cpm_qe/qe/par_io.txt was saying:

   - compatible : should be "fsl,<chip>-qe-pario-bank", 
"fsl,mpc8323-qe-pario-bank".

Which I first translated in yaml as :

   properties:
     compatible:
       items:
         - enum:
           - fsl,<chip>-qe-pario-bank
         - const: fsl,mpc8323-qe-pario-bank

But 'make dt_binding_check' complained about the < > around 'chip' so I 
removed them.

How should it be described ?

Thanks
Christophe