From: Weike Chen <alvin.chen@intel.com>
To: Linus Walleij <linus.walleij@linaro.org>,
Alexandre Courbot <gnurou@gmail.com>,
Grant Likely <grant.likely@linaro.org>,
Rob Herring <robh+dt@kernel.org>,
atull <atull@opensource.altera.com>
Cc: linux-gpio@vger.kernel.org, linux-kernel@vger.kernel.org,
devicetree@vger.kernel.org,
Boon Leong Ong <boon.leong.ong@intel.com>,
Hock Leong Kweh <hock.leong.kweh@intel.com>,
Darren Hart <dvhart@linux.intel.com>,
Sebastian Andrzej Siewior <sebastian@breakpoint.cc>,
Mika Westerberg <mika.westerberg@intel.com>,
Andy Shevchenko <andriy.shevchenko@linux.intel.com>,
Alvin Chen <alvin.chen@intel.com>
Subject: [PATCH 4/4 v5] GPIO: gpio-dwapb: Suspend & Resume PM enabling
Date: Wed, 17 Sep 2014 09:18:42 -0700 [thread overview]
Message-ID: <1410970722-8579-5-git-send-email-alvin.chen@intel.com> (raw)
In-Reply-To: <1410970722-8579-1-git-send-email-alvin.chen@intel.com>
This patch enables suspend and resume mode for the power management, and
it is based on Josef Ahmad's previous work.
Reviewed-by: Hock Leong Kweh <hock.leong.kweh@intel.com>
Signed-off-by: Weike Chen <alvin.chen@intel.com>
---
drivers/gpio/gpio-dwapb.c | 115 +++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 115 insertions(+)
diff --git a/drivers/gpio/gpio-dwapb.c b/drivers/gpio/gpio-dwapb.c
index db059bb..7feaf9d 100644
--- a/drivers/gpio/gpio-dwapb.c
+++ b/drivers/gpio/gpio-dwapb.c
@@ -51,10 +51,28 @@
struct dwapb_gpio;
+#ifdef CONFIG_PM_SLEEP
+/* Store GPIO context across system-wide suspend/resume transitions */
+struct dwapb_context {
+ u32 data;
+ u32 dir;
+ u32 ext;
+ u32 int_en;
+ u32 int_mask;
+ u32 int_type;
+ u32 int_pol;
+ u32 int_deb;
+};
+#endif
+
struct dwapb_gpio_port {
struct bgpio_chip bgc;
bool is_registered;
struct dwapb_gpio *gpio;
+#ifdef CONFIG_PM_SLEEP
+ struct dwapb_context *ctx;
+#endif
+ unsigned int idx;
};
struct dwapb_gpio {
@@ -381,6 +399,13 @@ static int dwapb_gpio_add_port(struct dwapb_gpio *gpio,
port = &gpio->ports[offs];
port->gpio = gpio;
+ port->idx = pp->idx;
+
+#ifdef CONFIG_PM_SLEEP
+ port->ctx = devm_kzalloc(gpio->dev, sizeof(*port->ctx), GFP_KERNEL);
+ if (!port->ctx)
+ return -ENOMEM;
+#endif
dat = gpio->regs + GPIO_EXT_PORTA + (pp->idx * GPIO_EXT_PORT_SIZE);
set = gpio->regs + GPIO_SWPORTA_DR + (pp->idx * GPIO_SWPORT_DR_SIZE);
@@ -586,10 +611,100 @@ static const struct of_device_id dwapb_of_match[] = {
};
MODULE_DEVICE_TABLE(of, dwapb_of_match);
+#ifdef CONFIG_PM_SLEEP
+static int dwapb_gpio_suspend(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct dwapb_gpio *gpio = platform_get_drvdata(pdev);
+ struct bgpio_chip *bgc = &gpio->ports[0].bgc;
+ unsigned long flags;
+ int i;
+
+ spin_lock_irqsave(&bgc->lock, flags);
+ for (i = 0; i < gpio->nr_ports; i++) {
+ unsigned int offset;
+ unsigned int idx = gpio->ports[i].idx;
+ struct dwapb_context *ctx = gpio->ports[i].ctx;
+
+ BUG_ON(ctx == 0);
+
+ offset = GPIO_SWPORTA_DDR + idx * GPIO_SWPORT_DDR_SIZE;
+ ctx->dir = dwapb_read(gpio, offset);
+
+ offset = GPIO_SWPORTA_DR + idx * GPIO_SWPORT_DR_SIZE;
+ ctx->data = dwapb_read(gpio, offset);
+
+ offset = GPIO_EXT_PORTA + idx * GPIO_EXT_PORT_SIZE;
+ ctx->ext = dwapb_read(gpio, offset);
+
+ /* Only port A can provide interrupts */
+ if (idx == 0) {
+ ctx->int_mask = dwapb_read(gpio, GPIO_INTMASK);
+ ctx->int_en = dwapb_read(gpio, GPIO_INTEN);
+ ctx->int_pol = dwapb_read(gpio, GPIO_INT_POLARITY);
+ ctx->int_type = dwapb_read(gpio, GPIO_INTTYPE_LEVEL);
+ ctx->int_deb = dwapb_read(gpio, GPIO_PORTA_DEBOUNCE);
+
+ /* Mask out interrupts */
+ dwapb_write(gpio, GPIO_INTMASK, 0xffffffff);
+ }
+ }
+ spin_unlock_irqrestore(&bgc->lock, flags);
+
+ return 0;
+}
+
+static int dwapb_gpio_resume(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct dwapb_gpio *gpio = platform_get_drvdata(pdev);
+ struct bgpio_chip *bgc = &gpio->ports[0].bgc;
+ unsigned long flags;
+ int i;
+
+ spin_lock_irqsave(&bgc->lock, flags);
+ for (i = 0; i < gpio->nr_ports; i++) {
+ unsigned int offset;
+ unsigned int idx = gpio->ports[i].idx;
+ struct dwapb_context *ctx = gpio->ports[i].ctx;
+
+ BUG_ON(ctx == 0);
+
+ offset = GPIO_SWPORTA_DR + idx * GPIO_SWPORT_DR_SIZE;
+ dwapb_write(gpio, offset, ctx->data);
+
+ offset = GPIO_SWPORTA_DDR + idx * GPIO_SWPORT_DDR_SIZE;
+ dwapb_write(gpio, offset, ctx->dir);
+
+ offset = GPIO_EXT_PORTA + idx * GPIO_EXT_PORT_SIZE;
+ dwapb_write(gpio, offset, ctx->ext);
+
+ /* Only port A can provide interrupts */
+ if (idx == 0) {
+ dwapb_write(gpio, GPIO_INTTYPE_LEVEL, ctx->int_type);
+ dwapb_write(gpio, GPIO_INT_POLARITY, ctx->int_pol);
+ dwapb_write(gpio, GPIO_PORTA_DEBOUNCE, ctx->int_deb);
+ dwapb_write(gpio, GPIO_INTEN, ctx->int_en);
+ dwapb_write(gpio, GPIO_INTMASK, ctx->int_mask);
+
+ /* Clear out spurious interrupts */
+ dwapb_write(gpio, GPIO_PORTA_EOI, 0xffffffff);
+ }
+ }
+ spin_unlock_irqrestore(&bgc->lock, flags);
+
+ return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(dwapb_gpio_pm_ops, dwapb_gpio_suspend,
+ dwapb_gpio_resume);
+
static struct platform_driver dwapb_gpio_driver = {
.driver = {
.name = "gpio-dwapb",
.owner = THIS_MODULE,
+ .pm = &dwapb_gpio_pm_ops,
.of_match_table = of_match_ptr(dwapb_of_match),
},
.probe = dwapb_gpio_probe,
--
1.7.9.5
next prev parent reply other threads:[~2014-09-17 16:18 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-09-17 16:18 [PATCH 0/4 v5] The Designware GPIO Supporting Weike Chen
2014-09-17 16:18 ` [PATCH 1/4 v5] GPIO: gpio-dwapb: Enable platform driver binding to MFD driver Weike Chen
2014-09-23 12:09 ` Linus Walleij
2014-09-17 16:18 ` [PATCH 2/4 v5] GPIO: gpio-dwapb: Change readl&writel to dwapb_read&dwapb_write Weike Chen
2014-09-23 12:10 ` Linus Walleij
2014-09-17 16:18 ` [PATCH 3/4 v5] GPIO: gpio-dwapb: Support Debounce Weike Chen
2014-09-23 12:12 ` Linus Walleij
2014-09-17 16:18 ` Weike Chen [this message]
2014-09-17 8:50 ` [PATCH 4/4 v5] GPIO: gpio-dwapb: Suspend & Resume PM enabling Andy Shevchenko
2014-09-23 14:41 ` Linus Walleij
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1410970722-8579-5-git-send-email-alvin.chen@intel.com \
--to=alvin.chen@intel.com \
--cc=andriy.shevchenko@linux.intel.com \
--cc=atull@opensource.altera.com \
--cc=boon.leong.ong@intel.com \
--cc=devicetree@vger.kernel.org \
--cc=dvhart@linux.intel.com \
--cc=gnurou@gmail.com \
--cc=grant.likely@linaro.org \
--cc=hock.leong.kweh@intel.com \
--cc=linus.walleij@linaro.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mika.westerberg@intel.com \
--cc=robh+dt@kernel.org \
--cc=sebastian@breakpoint.cc \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).