From: Geert Uytterhoeven <geert+renesas@glider.be>
To: Linus Walleij <linus.walleij@linaro.org>,
Alexandre Courbot <gnurou@gmail.com>
Cc: Magnus Damm <magnus.damm@gmail.com>,
linux-gpio@vger.kernel.org, linux-pm@vger.kernel.org,
linux-sh@vger.kernel.org,
Geert Uytterhoeven <geert+renesas@glider.be>
Subject: [PATCH] gpio: rcar: Fine-grained Runtime PM support
Date: Thu, 25 Jun 2015 16:45:57 +0200 [thread overview]
Message-ID: <1435243557-7050-1-git-send-email-geert+renesas@glider.be> (raw)
Currently gpio modules are runtime-resumed at probe time. This means the
gpio module will be active all the time (except during system suspend,
if not configured as a wake-up source).
While an R-Car Gen2 gpio module retains pins configured for output at
the requested level while put in standby mode, gpio registercannot be
accessed while suspended. Unfortunately pm_runtime_get_sync() cannot be
called from all contexts where gpio register access is needed. Hence
move the Runtime PM handling from probe/remove time to gpio request/free
time, which is probably the best we can do.
On r8a7791/koelsch, gpio modules 0, 1, 3, and 4 are now suspended during
normal use (gpio2 is used for LEDs and regulators, gpio5 for keys, gpio6
for SD-Card CD & WP, gpio7 for keys and regulators).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
drivers/gpio/gpio-rcar.c | 20 ++++++++++++++++----
1 file changed, 16 insertions(+), 4 deletions(-)
diff --git a/drivers/gpio/gpio-rcar.c b/drivers/gpio/gpio-rcar.c
index 29089ef6969fd33f..099a6f508f867821 100644
--- a/drivers/gpio/gpio-rcar.c
+++ b/drivers/gpio/gpio-rcar.c
@@ -251,17 +251,32 @@ static void gpio_rcar_config_general_input_output_mode(struct gpio_chip *chip,
static int gpio_rcar_request(struct gpio_chip *chip, unsigned offset)
{
- return pinctrl_request_gpio(chip->base + offset);
+ struct gpio_rcar_priv *p = gpio_to_priv(chip);
+ int error;
+
+ error = pm_runtime_get_sync(&p->pdev->dev);
+ if (error < 0)
+ return error;
+
+ error = pinctrl_request_gpio(chip->base + offset);
+ if (error)
+ pm_runtime_put(&p->pdev->dev);
+
+ return error;
}
static void gpio_rcar_free(struct gpio_chip *chip, unsigned offset)
{
+ struct gpio_rcar_priv *p = gpio_to_priv(chip);
+
pinctrl_free_gpio(chip->base + offset);
/* Set the GPIO as an input to ensure that the next GPIO request won't
* drive the GPIO pin as an output.
*/
gpio_rcar_config_general_input_output_mode(chip, offset, false);
+
+ pm_runtime_put(&p->pdev->dev);
}
static int gpio_rcar_direction_input(struct gpio_chip *chip, unsigned offset)
@@ -405,7 +420,6 @@ static int gpio_rcar_probe(struct platform_device *pdev)
}
pm_runtime_enable(dev);
- pm_runtime_get_sync(dev);
io = platform_get_resource(pdev, IORESOURCE_MEM, 0);
irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
@@ -488,7 +502,6 @@ static int gpio_rcar_probe(struct platform_device *pdev)
err1:
gpiochip_remove(gpio_chip);
err0:
- pm_runtime_put(dev);
pm_runtime_disable(dev);
return ret;
}
@@ -499,7 +512,6 @@ static int gpio_rcar_remove(struct platform_device *pdev)
gpiochip_remove(&p->gpio_chip);
- pm_runtime_put(&pdev->dev);
pm_runtime_disable(&pdev->dev);
return 0;
}
--
1.9.1
next reply other threads:[~2015-06-25 14:46 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-06-25 14:45 Geert Uytterhoeven [this message]
2015-07-16 8:43 ` [PATCH] gpio: rcar: Fine-grained Runtime PM support Linus Walleij
2015-07-16 9:05 ` Magnus Damm
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1435243557-7050-1-git-send-email-geert+renesas@glider.be \
--to=geert+renesas@glider.be \
--cc=gnurou@gmail.com \
--cc=linus.walleij@linaro.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=linux-sh@vger.kernel.org \
--cc=magnus.damm@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).