[PATCH v3 0/3] Add basic support for Allwinner A83T SOC

[PATCH v3 0/3] Add basic support for Allwinner A83T SOC

[Vishnu Patekar]

This patch series adds very basic support for Allwinner A83T SOC.
Clock, peripherals, smp support will be added later.

Allwinner A83T is octa-core cortex-a7 based SoC.
It's clock control unit and prcm, pinmux are different from previous sun8i
series.
Its processor cores are arragned in two clusters 4 cores each,
similar to A80.

Note: A83T pincontroller patch is already applied by Linus, so not added in this
patch.

changes from v2->v3
1. removed "Not Supported" for A83T in sunxi/README
2. removed un-unsed nodes from dtsi.
3. corrected GIC_SPI number for PH_EINT in dtsi.
4. removed address at soc node which was un-necessary.
5. corrected reg<> addresses for cpu nodes.
6. changed cpu mask to 8 in gic and archtimer node.


changes from v1->v2:
1. used UART0 header with PB9, PB10 pins.
2. removed unnecessary includes and comments from dtsi.
3. arranged nodes in alphabatical order.
4. arrnaged compatible in alphabatical order.
5. changed cpu nodes to use cpu@100 -cpu@-103.
6. changed dts filename.

Vishnu Patekar (3):
  ARM: sunxi: Introduce Allwinner for A83T support
  ARM: dts: sun8i: Add Allwinner A83T dtsi
  ARM: dts: sun8i: Add A83T HomletV2 Board by Allwinner

 Documentation/arm/sunxi/README                     |   1 -
 Documentation/devicetree/bindings/arm/sunxi.txt    |   1 +
 arch/arm/boot/dts/Makefile                         |   1 +
 .../boot/dts/sun8i-a83t-allwinner-h8homlet-v2.dts  |  64 +++++++
 arch/arm/boot/dts/sun8i-a83t.dtsi                  | 206 +++++++++++++++++++++
 arch/arm/mach-sunxi/sunxi.c                        |   1 +
 drivers/clk/sunxi/clk-sunxi.c                      |   6 +
 7 files changed, 279 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/boot/dts/sun8i-a83t-allwinner-h8homlet-v2.dts
 create mode 100644 arch/arm/boot/dts/sun8i-a83t.dtsi

-- 
1.9.1

[PATCH v3 1/3] ARM: sunxi: Introduce Allwinner for A83T support

[Vishnu Patekar]

Allwinner A83T is octa-core cortex-a7 based SoC.
It's clock control unit and prcm, pinmux are different from previous sun8i
series.
Its processor cores are arragned in two clusters 4 cores each,
similar to A80.

Signed-off-by: Vishnu Patekar <vishnupatekar0510-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
 Documentation/arm/sunxi/README                  | 1 -
 Documentation/devicetree/bindings/arm/sunxi.txt | 1 +
 arch/arm/mach-sunxi/sunxi.c                     | 1 +
 drivers/clk/sunxi/clk-sunxi.c                   | 6 ++++++
 4 files changed, 8 insertions(+), 1 deletion(-)

diff --git a/Documentation/arm/sunxi/README b/Documentation/arm/sunxi/README
index 430d279..e5a115f 100644
--- a/Documentation/arm/sunxi/README
+++ b/Documentation/arm/sunxi/README
@@ -72,6 +72,5 @@ SunXi family
 
     * Octa ARM Cortex-A7 based SoCs
       - Allwinner A83T
-        + Not Supported
         + Datasheet
           http://dl.linux-sunxi.org/A83T/A83T_datasheet_Revision_1.1.pdf
diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt
index bb9b0faa..7e79fcc 100644
--- a/Documentation/devicetree/bindings/arm/sunxi.txt
+++ b/Documentation/devicetree/bindings/arm/sunxi.txt
@@ -11,5 +11,6 @@ using one of the following compatible strings:
   allwinner,sun7i-a20
   allwinner,sun8i-a23
   allwinner,sun8i-a33
+  allwinner,sun8i-a83t
   allwinner,sun8i-h3
   allwinner,sun9i-a80
diff --git a/arch/arm/mach-sunxi/sunxi.c b/arch/arm/mach-sunxi/sunxi.c
index c2be98f..3c15619 100644
--- a/arch/arm/mach-sunxi/sunxi.c
+++ b/arch/arm/mach-sunxi/sunxi.c
@@ -69,6 +69,7 @@ MACHINE_END
 static const char * const sun8i_board_dt_compat[] = {
 	"allwinner,sun8i-a23",
 	"allwinner,sun8i-a33",
+	"allwinner,sun8i-a83t",
 	"allwinner,sun8i-h3",
 	NULL,
 };
diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
index 5ba2188..0d45253 100644
--- a/drivers/clk/sunxi/clk-sunxi.c
+++ b/drivers/clk/sunxi/clk-sunxi.c
@@ -1219,6 +1219,12 @@ CLK_OF_DECLARE(sun8i_a23_clk_init, "allwinner,sun8i-a23", sun6i_init_clocks);
 CLK_OF_DECLARE(sun8i_a33_clk_init, "allwinner,sun8i-a33", sun6i_init_clocks);
 CLK_OF_DECLARE(sun8i_h3_clk_init, "allwinner,sun8i-h3", sun6i_init_clocks);
 
+static void __init sun8i_a83t_init_clocks(struct device_node *node)
+{
+	sunxi_init_clocks(NULL, 0);
+}
+CLK_OF_DECLARE(sun8i_a83t_clk_init, "allwinner,sun8i-a83t", sun8i_a83t_init_clocks);
+
 static void __init sun9i_init_clocks(struct device_node *node)
 {
 	sunxi_init_clocks(NULL, 0);
-- 
1.9.1

Re: [PATCH v3 1/3] ARM: sunxi: Introduce Allwinner for A83T support

[Rob Herring]

On Fri, Dec 18, 2015 at 09:30:49PM +0800, Vishnu Patekar wrote:
> Allwinner A83T is octa-core cortex-a7 based SoC.
> It's clock control unit and prcm, pinmux are different from previous sun8i
> series.
> Its processor cores are arragned in two clusters 4 cores each,
> similar to A80.
> 
> Signed-off-by: Vishnu Patekar <vishnupatekar0510-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>

Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>

> ---
>  Documentation/arm/sunxi/README                  | 1 -
>  Documentation/devicetree/bindings/arm/sunxi.txt | 1 +
>  arch/arm/mach-sunxi/sunxi.c                     | 1 +
>  drivers/clk/sunxi/clk-sunxi.c                   | 6 ++++++
>  4 files changed, 8 insertions(+), 1 deletion(-)
> 
> diff --git a/Documentation/arm/sunxi/README b/Documentation/arm/sunxi/README
> index 430d279..e5a115f 100644
> --- a/Documentation/arm/sunxi/README
> +++ b/Documentation/arm/sunxi/README
> @@ -72,6 +72,5 @@ SunXi family
>  
>      * Octa ARM Cortex-A7 based SoCs
>        - Allwinner A83T
> -        + Not Supported
>          + Datasheet
>            http://dl.linux-sunxi.org/A83T/A83T_datasheet_Revision_1.1.pdf
> diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt
> index bb9b0faa..7e79fcc 100644
> --- a/Documentation/devicetree/bindings/arm/sunxi.txt
> +++ b/Documentation/devicetree/bindings/arm/sunxi.txt
> @@ -11,5 +11,6 @@ using one of the following compatible strings:
>    allwinner,sun7i-a20
>    allwinner,sun8i-a23
>    allwinner,sun8i-a33
> +  allwinner,sun8i-a83t
>    allwinner,sun8i-h3
>    allwinner,sun9i-a80
> diff --git a/arch/arm/mach-sunxi/sunxi.c b/arch/arm/mach-sunxi/sunxi.c
> index c2be98f..3c15619 100644
> --- a/arch/arm/mach-sunxi/sunxi.c
> +++ b/arch/arm/mach-sunxi/sunxi.c
> @@ -69,6 +69,7 @@ MACHINE_END
>  static const char * const sun8i_board_dt_compat[] = {
>  	"allwinner,sun8i-a23",
>  	"allwinner,sun8i-a33",
> +	"allwinner,sun8i-a83t",
>  	"allwinner,sun8i-h3",
>  	NULL,
>  };
> diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
> index 5ba2188..0d45253 100644
> --- a/drivers/clk/sunxi/clk-sunxi.c
> +++ b/drivers/clk/sunxi/clk-sunxi.c
> @@ -1219,6 +1219,12 @@ CLK_OF_DECLARE(sun8i_a23_clk_init, "allwinner,sun8i-a23", sun6i_init_clocks);
>  CLK_OF_DECLARE(sun8i_a33_clk_init, "allwinner,sun8i-a33", sun6i_init_clocks);
>  CLK_OF_DECLARE(sun8i_h3_clk_init, "allwinner,sun8i-h3", sun6i_init_clocks);
>  
> +static void __init sun8i_a83t_init_clocks(struct device_node *node)
> +{
> +	sunxi_init_clocks(NULL, 0);
> +}
> +CLK_OF_DECLARE(sun8i_a83t_clk_init, "allwinner,sun8i-a83t", sun8i_a83t_init_clocks);
> +
>  static void __init sun9i_init_clocks(struct device_node *node)
>  {
>  	sunxi_init_clocks(NULL, 0);
> -- 
> 1.9.1
> 

[PATCH v3 2/3] ARM: dts: sun8i: Add Allwinner A83T dtsi

[Vishnu Patekar]

Allwinner A83T is new octa-core cortex-a7 SOC.
This adds the basic dtsi, the clocks differs from
earlier sun8i SOCs.

Signed-off-by: Vishnu Patekar <vishnupatekar0510-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
 arch/arm/boot/dts/sun8i-a83t.dtsi | 206 ++++++++++++++++++++++++++++++++++++++
 1 file changed, 206 insertions(+)
 create mode 100644 arch/arm/boot/dts/sun8i-a83t.dtsi

diff --git a/arch/arm/boot/dts/sun8i-a83t.dtsi b/arch/arm/boot/dts/sun8i-a83t.dtsi
new file mode 100644
index 0000000..e577c64
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-a83t.dtsi
@@ -0,0 +1,206 @@
+/*
+ * Copyright 2015 Vishnu Patekar
+ *
+ * Vishnu Patekar <vishnupatekar0510-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+
+ */
+
+#include "skeleton.dtsi"
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+	interrupt-parent = <&gic>;
+
+	chosen {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <0>;
+		};
+
+		cpu@1 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <1>;
+		};
+
+		cpu@2 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <2>;
+		};
+
+		cpu@3 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <3>;
+		};
+		cpu@100 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <0x100>;
+		};
+
+		cpu@101 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <0x101>;
+		};
+		cpu@102 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <0x102>;
+		};
+
+		cpu@103 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <0x103>;
+		};
+	};
+
+	memory {
+		reg = <0x40000000 0x80000000>;
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		osc24M: osc24M_clk {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <24000000>;
+			clock-output-names = "osc24M";
+		};
+
+		osc32k: osc32k_clk {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <32768>;
+			clock-output-names = "osc32k";
+		};
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		gic: interrupt-controller@01c81000 {
+			compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
+			reg = <0x01c81000 0x1000>,
+			      <0x01c82000 0x1000>,
+			      <0x01c84000 0x2000>,
+			      <0x01c86000 0x2000>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
+		};
+
+		pio: pinctrl@01c20800 {
+			compatible = "allwinner,sun8i-a83t-pinctrl";
+			interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+			reg = <0x01c20800 0x400>;
+			clocks = <&osc24M>;
+			gpio-controller;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			#gpio-cells = <3>;
+
+			mmc0_pins_a: mmc0@0 {
+				allwinner,pins = "PF0", "PF1", "PF2",
+						 "PF3", "PF4", "PF5";
+				allwinner,function = "mmc0";
+				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+
+			uart0_pins_a: uart0@0 {
+				allwinner,pins = "PF2", "PF4";
+				allwinner,function = "uart0";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+
+			uart0_pins_b: uart0@1 {
+				allwinner,pins = "PB9", "PB10";
+				allwinner,function = "uart0";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+		};
+
+		uart0: serial@01c28000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28000 0x400>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&osc24M>;
+			status = "disabled";
+		};
+	};
+};
-- 
1.9.1

Re: [PATCH v3 2/3] ARM: dts: sun8i: Add Allwinner A83T dtsi

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 7113 bytes --]

Hi,

On Fri, Dec 18, 2015 at 09:30:50PM +0800, Vishnu Patekar wrote:
> Allwinner A83T is new octa-core cortex-a7 SOC.
> This adds the basic dtsi, the clocks differs from
> earlier sun8i SOCs.
> 
> Signed-off-by: Vishnu Patekar <vishnupatekar0510-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> ---
>  arch/arm/boot/dts/sun8i-a83t.dtsi | 206 ++++++++++++++++++++++++++++++++++++++
>  1 file changed, 206 insertions(+)
>  create mode 100644 arch/arm/boot/dts/sun8i-a83t.dtsi
> 
> diff --git a/arch/arm/boot/dts/sun8i-a83t.dtsi b/arch/arm/boot/dts/sun8i-a83t.dtsi
> new file mode 100644
> index 0000000..e577c64
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun8i-a83t.dtsi
> @@ -0,0 +1,206 @@
> +/*
> + * Copyright 2015 Vishnu Patekar
> + *
> + * Vishnu Patekar <vishnupatekar0510-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful,
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use,
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> +
> + */
> +
> +#include "skeleton.dtsi"
> +
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +
> +#include <dt-bindings/pinctrl/sun4i-a10.h>
> +
> +/ {
> +	interrupt-parent = <&gic>;
> +
> +	chosen {
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges;
> +	};
> +
> +	cpus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		cpu@0 {
> +			compatible = "arm,cortex-a7";
> +			device_type = "cpu";
> +			reg = <0>;
> +		};
> +
> +		cpu@1 {
> +			compatible = "arm,cortex-a7";
> +			device_type = "cpu";
> +			reg = <1>;
> +		};
> +
> +		cpu@2 {
> +			compatible = "arm,cortex-a7";
> +			device_type = "cpu";
> +			reg = <2>;
> +		};
> +
> +		cpu@3 {
> +			compatible = "arm,cortex-a7";
> +			device_type = "cpu";
> +			reg = <3>;
> +		};

A \n here please

> +		cpu@100 {
> +			compatible = "arm,cortex-a7";
> +			device_type = "cpu";
> +			reg = <0x100>;
> +		};
> +
> +		cpu@101 {
> +			compatible = "arm,cortex-a7";
> +			device_type = "cpu";
> +			reg = <0x101>;
> +		};

Ditto.

> +		cpu@102 {
> +			compatible = "arm,cortex-a7";
> +			device_type = "cpu";
> +			reg = <0x102>;
> +		};
> +
> +		cpu@103 {
> +			compatible = "arm,cortex-a7";
> +			device_type = "cpu";
> +			reg = <0x103>;
> +		};
> +	};
> +
> +	memory {
> +		reg = <0x40000000 0x80000000>;
> +	};

Is mainline u-boot usable ? If so, you can remove that node entirely.

> +
> +	timer {
> +		compatible = "arm,armv7-timer";
> +		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> +			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> +			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> +			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
> +	};
> +
> +	clocks {
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges;
> +
> +		osc24M: osc24M_clk {
> +			#clock-cells = <0>;
> +			compatible = "fixed-clock";
> +			clock-frequency = <24000000>;
> +			clock-output-names = "osc24M";
> +		};
> +
> +		osc32k: osc32k_clk {
> +			#clock-cells = <0>;
> +			compatible = "fixed-clock";
> +			clock-frequency = <32768>;
> +			clock-output-names = "osc32k";
> +		};

Do you need to modify the clocks driver in your first commit then?

> +	};
> +
> +	soc {
> +		compatible = "simple-bus";
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges;
> +
> +		gic: interrupt-controller@01c81000 {
> +			compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
> +			reg = <0x01c81000 0x1000>,
> +			      <0x01c82000 0x1000>,
> +			      <0x01c84000 0x2000>,
> +			      <0x01c86000 0x2000>;

Please order the nodes by ascending physical addresses.

> +			interrupt-controller;
> +			#interrupt-cells = <3>;
> +			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
> +		};
> +
> +		pio: pinctrl@01c20800 {
> +			compatible = "allwinner,sun8i-a83t-pinctrl";
> +			interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
> +			reg = <0x01c20800 0x400>;
> +			clocks = <&osc24M>;
> +			gpio-controller;
> +			interrupt-controller;
> +			#interrupt-cells = <3>;
> +			#gpio-cells = <3>;
> +
> +			mmc0_pins_a: mmc0@0 {
> +				allwinner,pins = "PF0", "PF1", "PF2",
> +						 "PF3", "PF4", "PF5";
> +				allwinner,function = "mmc0";
> +				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +			};
> +
> +			uart0_pins_a: uart0@0 {
> +				allwinner,pins = "PF2", "PF4";
> +				allwinner,function = "uart0";
> +				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +			};
> +
> +			uart0_pins_b: uart0@1 {
> +				allwinner,pins = "PB9", "PB10";
> +				allwinner,function = "uart0";
> +				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +			};
> +		};
> +
> +		uart0: serial@01c28000 {
> +			compatible = "snps,dw-apb-uart";
> +			reg = <0x01c28000 0x400>;
> +			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
> +			reg-shift = <2>;
> +			reg-io-width = <4>;
> +			clocks = <&osc24M>;
> +			status = "disabled";
> +		};
> +	};
> +};

Thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

Re: [linux-sunxi] Re: [PATCH v3 2/3] ARM: dts: sun8i: Add Allwinner A83T dtsi

[Hans de Goede]

Hi,

On 18-12-15 22:41, Maxime Ripard wrote:
> Hi,
>
> On Fri, Dec 18, 2015 at 09:30:50PM +0800, Vishnu Patekar wrote:
>> Allwinner A83T is new octa-core cortex-a7 SOC.
>> This adds the basic dtsi, the clocks differs from
>> earlier sun8i SOCs.
>>
>> Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
>> ---
>>   arch/arm/boot/dts/sun8i-a83t.dtsi | 206 ++++++++++++++++++++++++++++++++++++++
>>   1 file changed, 206 insertions(+)
>>   create mode 100644 arch/arm/boot/dts/sun8i-a83t.dtsi
>>
>> diff --git a/arch/arm/boot/dts/sun8i-a83t.dtsi b/arch/arm/boot/dts/sun8i-a83t.dtsi
>> new file mode 100644
>> index 0000000..e577c64
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/sun8i-a83t.dtsi
>> @@ -0,0 +1,206 @@
>> +/*
>> + * Copyright 2015 Vishnu Patekar
>> + *
>> + * Vishnu Patekar <vishnupatekar0510@gmail.com>
>> + *
>> + * This file is dual-licensed: you can use it either under the terms
>> + * of the GPL or the X11 license, at your option. Note that this dual
>> + * licensing only applies to this file, and not this project as a
>> + * whole.
>> + *
>> + *  a) This file is free software; you can redistribute it and/or
>> + *     modify it under the terms of the GNU General Public License as
>> + *     published by the Free Software Foundation; either version 2 of the
>> + *     License, or (at your option) any later version.
>> + *
>> + *     This file is distributed in the hope that it will be useful,
>> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> + *     GNU General Public License for more details.
>> + *
>> + * Or, alternatively,
>> + *
>> + *  b) Permission is hereby granted, free of charge, to any person
>> + *     obtaining a copy of this software and associated documentation
>> + *     files (the "Software"), to deal in the Software without
>> + *     restriction, including without limitation the rights to use,
>> + *     copy, modify, merge, publish, distribute, sublicense, and/or
>> + *     sell copies of the Software, and to permit persons to whom the
>> + *     Software is furnished to do so, subject to the following
>> + *     conditions:
>> + *
>> + *     The above copyright notice and this permission notice shall be
>> + *     included in all copies or substantial portions of the Software.
>> + *
>> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
>> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
>> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
>> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
>> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
>> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
>> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
>> + *     OTHER DEALINGS IN THE SOFTWARE.
>> +
>> + */
>> +
>> +#include "skeleton.dtsi"
>> +
>> +#include <dt-bindings/interrupt-controller/arm-gic.h>
>> +
>> +#include <dt-bindings/pinctrl/sun4i-a10.h>
>> +
>> +/ {
>> +	interrupt-parent = <&gic>;
>> +
>> +	chosen {
>> +		#address-cells = <1>;
>> +		#size-cells = <1>;
>> +		ranges;
>> +	};
>> +
>> +	cpus {
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +
>> +		cpu@0 {
>> +			compatible = "arm,cortex-a7";
>> +			device_type = "cpu";
>> +			reg = <0>;
>> +		};
>> +
>> +		cpu@1 {
>> +			compatible = "arm,cortex-a7";
>> +			device_type = "cpu";
>> +			reg = <1>;
>> +		};
>> +
>> +		cpu@2 {
>> +			compatible = "arm,cortex-a7";
>> +			device_type = "cpu";
>> +			reg = <2>;
>> +		};
>> +
>> +		cpu@3 {
>> +			compatible = "arm,cortex-a7";
>> +			device_type = "cpu";
>> +			reg = <3>;
>> +		};
>
> A \n here please
>
>> +		cpu@100 {
>> +			compatible = "arm,cortex-a7";
>> +			device_type = "cpu";
>> +			reg = <0x100>;
>> +		};
>> +
>> +		cpu@101 {
>> +			compatible = "arm,cortex-a7";
>> +			device_type = "cpu";
>> +			reg = <0x101>;
>> +		};
>
> Ditto.
>
>> +		cpu@102 {
>> +			compatible = "arm,cortex-a7";
>> +			device_type = "cpu";
>> +			reg = <0x102>;
>> +		};
>> +
>> +		cpu@103 {
>> +			compatible = "arm,cortex-a7";
>> +			device_type = "cpu";
>> +			reg = <0x103>;
>> +		};
>> +	};
>> +
>> +	memory {
>> +		reg = <0x40000000 0x80000000>;
>> +	};
>
> Is mainline u-boot usable ? If so, you can remove that node entirely.

mainline u-boot works for me when cold-booting from a sdcard, so I consider
it usable :)

Regards,

Hans



>
>> +
>> +	timer {
>> +		compatible = "arm,armv7-timer";
>> +		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
>> +			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
>> +			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
>> +			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
>> +	};
>> +
>> +	clocks {
>> +		#address-cells = <1>;
>> +		#size-cells = <1>;
>> +		ranges;
>> +
>> +		osc24M: osc24M_clk {
>> +			#clock-cells = <0>;
>> +			compatible = "fixed-clock";
>> +			clock-frequency = <24000000>;
>> +			clock-output-names = "osc24M";
>> +		};
>> +
>> +		osc32k: osc32k_clk {
>> +			#clock-cells = <0>;
>> +			compatible = "fixed-clock";
>> +			clock-frequency = <32768>;
>> +			clock-output-names = "osc32k";
>> +		};
>
> Do you need to modify the clocks driver in your first commit then?
>
>> +	};
>> +
>> +	soc {
>> +		compatible = "simple-bus";
>> +		#address-cells = <1>;
>> +		#size-cells = <1>;
>> +		ranges;
>> +
>> +		gic: interrupt-controller@01c81000 {
>> +			compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
>> +			reg = <0x01c81000 0x1000>,
>> +			      <0x01c82000 0x1000>,
>> +			      <0x01c84000 0x2000>,
>> +			      <0x01c86000 0x2000>;
>
> Please order the nodes by ascending physical addresses.
>
>> +			interrupt-controller;
>> +			#interrupt-cells = <3>;
>> +			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
>> +		};
>> +
>> +		pio: pinctrl@01c20800 {
>> +			compatible = "allwinner,sun8i-a83t-pinctrl";
>> +			interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
>> +				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
>> +				     <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
>> +			reg = <0x01c20800 0x400>;
>> +			clocks = <&osc24M>;
>> +			gpio-controller;
>> +			interrupt-controller;
>> +			#interrupt-cells = <3>;
>> +			#gpio-cells = <3>;
>> +
>> +			mmc0_pins_a: mmc0@0 {
>> +				allwinner,pins = "PF0", "PF1", "PF2",
>> +						 "PF3", "PF4", "PF5";
>> +				allwinner,function = "mmc0";
>> +				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
>> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> +			};
>> +
>> +			uart0_pins_a: uart0@0 {
>> +				allwinner,pins = "PF2", "PF4";
>> +				allwinner,function = "uart0";
>> +				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> +			};
>> +
>> +			uart0_pins_b: uart0@1 {
>> +				allwinner,pins = "PB9", "PB10";
>> +				allwinner,function = "uart0";
>> +				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> +			};
>> +		};
>> +
>> +		uart0: serial@01c28000 {
>> +			compatible = "snps,dw-apb-uart";
>> +			reg = <0x01c28000 0x400>;
>> +			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
>> +			reg-shift = <2>;
>> +			reg-io-width = <4>;
>> +			clocks = <&osc24M>;
>> +			status = "disabled";
>> +		};
>> +	};
>> +};
>
> Thanks!
> Maxime
>

Re: [linux-sunxi] Re: [PATCH v3 2/3] ARM: dts: sun8i: Add Allwinner A83T dtsi

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 490 bytes --]

Hi,

On Sat, Dec 19, 2015 at 11:57:03AM +0100, Hans de Goede wrote:
> >>+	memory {
> >>+		reg = <0x40000000 0x80000000>;
> >>+	};
> >
> >Is mainline u-boot usable ? If so, you can remove that node entirely.
> 
> mainline u-boot works for me when cold-booting from a sdcard, so I consider
> it usable :)

I'm glad we have the same definition of usable ;)

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

Re: [PATCH v3 2/3] ARM: dts: sun8i: Add Allwinner A83T dtsi

[Chen-Yu Tsai]

On Sat, Dec 19, 2015 at 5:41 AM, Maxime Ripard
<maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org> wrote:
> Hi,
>
> On Fri, Dec 18, 2015 at 09:30:50PM +0800, Vishnu Patekar wrote:
>> Allwinner A83T is new octa-core cortex-a7 SOC.
>> This adds the basic dtsi, the clocks differs from
>> earlier sun8i SOCs.
>>
>> Signed-off-by: Vishnu Patekar <vishnupatekar0510-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
>> ---
>>  arch/arm/boot/dts/sun8i-a83t.dtsi | 206 ++++++++++++++++++++++++++++++++++++++
>>  1 file changed, 206 insertions(+)
>>  create mode 100644 arch/arm/boot/dts/sun8i-a83t.dtsi
>>
>> diff --git a/arch/arm/boot/dts/sun8i-a83t.dtsi b/arch/arm/boot/dts/sun8i-a83t.dtsi
>> new file mode 100644
>> index 0000000..e577c64
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/sun8i-a83t.dtsi
>> @@ -0,0 +1,206 @@
>> +/*
>> + * Copyright 2015 Vishnu Patekar
>> + *
>> + * Vishnu Patekar <vishnupatekar0510-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
>> + *
>> + * This file is dual-licensed: you can use it either under the terms
>> + * of the GPL or the X11 license, at your option. Note that this dual
>> + * licensing only applies to this file, and not this project as a
>> + * whole.
>> + *
>> + *  a) This file is free software; you can redistribute it and/or
>> + *     modify it under the terms of the GNU General Public License as
>> + *     published by the Free Software Foundation; either version 2 of the
>> + *     License, or (at your option) any later version.
>> + *
>> + *     This file is distributed in the hope that it will be useful,
>> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> + *     GNU General Public License for more details.
>> + *
>> + * Or, alternatively,
>> + *
>> + *  b) Permission is hereby granted, free of charge, to any person
>> + *     obtaining a copy of this software and associated documentation
>> + *     files (the "Software"), to deal in the Software without
>> + *     restriction, including without limitation the rights to use,
>> + *     copy, modify, merge, publish, distribute, sublicense, and/or
>> + *     sell copies of the Software, and to permit persons to whom the
>> + *     Software is furnished to do so, subject to the following
>> + *     conditions:
>> + *
>> + *     The above copyright notice and this permission notice shall be
>> + *     included in all copies or substantial portions of the Software.
>> + *
>> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
>> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
>> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
>> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
>> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
>> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
>> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
>> + *     OTHER DEALINGS IN THE SOFTWARE.
>> +
>> + */
>> +
>> +#include "skeleton.dtsi"
>> +
>> +#include <dt-bindings/interrupt-controller/arm-gic.h>
>> +
>> +#include <dt-bindings/pinctrl/sun4i-a10.h>
>> +
>> +/ {
>> +     interrupt-parent = <&gic>;
>> +
>> +     chosen {
>> +             #address-cells = <1>;
>> +             #size-cells = <1>;
>> +             ranges;
>> +     };
>> +
>> +     cpus {
>> +             #address-cells = <1>;
>> +             #size-cells = <0>;
>> +
>> +             cpu@0 {
>> +                     compatible = "arm,cortex-a7";
>> +                     device_type = "cpu";
>> +                     reg = <0>;
>> +             };
>> +
>> +             cpu@1 {
>> +                     compatible = "arm,cortex-a7";
>> +                     device_type = "cpu";
>> +                     reg = <1>;
>> +             };
>> +
>> +             cpu@2 {
>> +                     compatible = "arm,cortex-a7";
>> +                     device_type = "cpu";
>> +                     reg = <2>;
>> +             };
>> +
>> +             cpu@3 {
>> +                     compatible = "arm,cortex-a7";
>> +                     device_type = "cpu";
>> +                     reg = <3>;
>> +             };
>
> A \n here please
>
>> +             cpu@100 {
>> +                     compatible = "arm,cortex-a7";
>> +                     device_type = "cpu";
>> +                     reg = <0x100>;
>> +             };
>> +
>> +             cpu@101 {
>> +                     compatible = "arm,cortex-a7";
>> +                     device_type = "cpu";
>> +                     reg = <0x101>;
>> +             };
>
> Ditto.
>
>> +             cpu@102 {
>> +                     compatible = "arm,cortex-a7";
>> +                     device_type = "cpu";
>> +                     reg = <0x102>;
>> +             };
>> +
>> +             cpu@103 {
>> +                     compatible = "arm,cortex-a7";
>> +                     device_type = "cpu";
>> +                     reg = <0x103>;
>> +             };
>> +     };
>> +
>> +     memory {
>> +             reg = <0x40000000 0x80000000>;
>> +     };
>
> Is mainline u-boot usable ? If so, you can remove that node entirely.
>
>> +
>> +     timer {
>> +             compatible = "arm,armv7-timer";
>> +             interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
>> +                          <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
>> +                          <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
>> +                          <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
>> +     };
>> +
>> +     clocks {
>> +             #address-cells = <1>;
>> +             #size-cells = <1>;
>> +             ranges;
>> +
>> +             osc24M: osc24M_clk {
>> +                     #clock-cells = <0>;
>> +                     compatible = "fixed-clock";
>> +                     clock-frequency = <24000000>;
>> +                     clock-output-names = "osc24M";
>> +             };
>> +
>> +             osc32k: osc32k_clk {
>> +                     #clock-cells = <0>;
>> +                     compatible = "fixed-clock";
>> +                     clock-frequency = <32768>;
>> +                     clock-output-names = "osc32k";
>> +             };
>
> Do you need to modify the clocks driver in your first commit then?
>
>> +     };
>> +
>> +     soc {
>> +             compatible = "simple-bus";
>> +             #address-cells = <1>;
>> +             #size-cells = <1>;
>> +             ranges;
>> +
>> +             gic: interrupt-controller@01c81000 {
>> +                     compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
>> +                     reg = <0x01c81000 0x1000>,
>> +                           <0x01c82000 0x1000>,
>> +                           <0x01c84000 0x2000>,
>> +                           <0x01c86000 0x2000>;
>
> Please order the nodes by ascending physical addresses.
>
>> +                     interrupt-controller;
>> +                     #interrupt-cells = <3>;
>> +                     interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
>> +             };
>> +
>> +             pio: pinctrl@01c20800 {
>> +                     compatible = "allwinner,sun8i-a83t-pinctrl";
>> +                     interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
>> +                                  <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
>> +                                  <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
>> +                     reg = <0x01c20800 0x400>;
>> +                     clocks = <&osc24M>;
>> +                     gpio-controller;
>> +                     interrupt-controller;
>> +                     #interrupt-cells = <3>;
>> +                     #gpio-cells = <3>;
>> +
>> +                     mmc0_pins_a: mmc0@0 {
>> +                             allwinner,pins = "PF0", "PF1", "PF2",
>> +                                              "PF3", "PF4", "PF5";
>> +                             allwinner,function = "mmc0";
>> +                             allwinner,drive = <SUN4I_PINCTRL_30_MA>;
>> +                             allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> +                     };
>> +
>> +                     uart0_pins_a: uart0@0 {
>> +                             allwinner,pins = "PF2", "PF4";
>> +                             allwinner,function = "uart0";
>> +                             allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> +                             allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> +                     };

I don't see much use for the UART0 PF pins once we have mmc working.

ChenYu

>> +
>> +                     uart0_pins_b: uart0@1 {
>> +                             allwinner,pins = "PB9", "PB10";
>> +                             allwinner,function = "uart0";
>> +                             allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> +                             allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> +                     };
>> +             };
>> +
>> +             uart0: serial@01c28000 {
>> +                     compatible = "snps,dw-apb-uart";
>> +                     reg = <0x01c28000 0x400>;
>> +                     interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
>> +                     reg-shift = <2>;
>> +                     reg-io-width = <4>;
>> +                     clocks = <&osc24M>;
>> +                     status = "disabled";
>> +             };
>> +     };
>> +};
>
> Thanks!
> Maxime
>
> --
> Maxime Ripard, Free Electrons
> Embedded Linux, Kernel and Android engineering
> http://free-electrons.com

Re: [linux-sunxi] Re: [PATCH v3 2/3] ARM: dts: sun8i: Add Allwinner A83T dtsi

[Vishnu Patekar]

Hello Wens,

On Tue, Dec 22, 2015 at 11:12 AM, Chen-Yu Tsai <wens@csie.org> wrote:
> On Sat, Dec 19, 2015 at 5:41 AM, Maxime Ripard
> <maxime.ripard@free-electrons.com> wrote:
>> Hi,
>>
>> On Fri, Dec 18, 2015 at 09:30:50PM +0800, Vishnu Patekar wrote:
>>> Allwinner A83T is new octa-core cortex-a7 SOC.
>>> This adds the basic dtsi, the clocks differs from
>>> earlier sun8i SOCs.
>>>
>>> Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
>>> ---
>>>  arch/arm/boot/dts/sun8i-a83t.dtsi | 206 ++++++++++++++++++++++++++++++++++++++
>>>  1 file changed, 206 insertions(+)
>>>  create mode 100644 arch/arm/boot/dts/sun8i-a83t.dtsi
>>>
>>> diff --git a/arch/arm/boot/dts/sun8i-a83t.dtsi b/arch/arm/boot/dts/sun8i-a83t.dtsi
>>> new file mode 100644
>>> index 0000000..e577c64
>>> --- /dev/null
>>> +++ b/arch/arm/boot/dts/sun8i-a83t.dtsi
>>> @@ -0,0 +1,206 @@
>>> +/*
>>> + * Copyright 2015 Vishnu Patekar
>>> + *
>>> + * Vishnu Patekar <vishnupatekar0510@gmail.com>
>>> + *
>>> + * This file is dual-licensed: you can use it either under the terms
>>> + * of the GPL or the X11 license, at your option. Note that this dual
>>> + * licensing only applies to this file, and not this project as a
>>> + * whole.
>>> + *
>>> + *  a) This file is free software; you can redistribute it and/or
>>> + *     modify it under the terms of the GNU General Public License as
>>> + *     published by the Free Software Foundation; either version 2 of the
>>> + *     License, or (at your option) any later version.
>>> + *
>>> + *     This file is distributed in the hope that it will be useful,
>>> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
>>> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>>> + *     GNU General Public License for more details.
>>> + *
>>> + * Or, alternatively,
>>> + *
>>> + *  b) Permission is hereby granted, free of charge, to any person
>>> + *     obtaining a copy of this software and associated documentation
>>> + *     files (the "Software"), to deal in the Software without
>>> + *     restriction, including without limitation the rights to use,
>>> + *     copy, modify, merge, publish, distribute, sublicense, and/or
>>> + *     sell copies of the Software, and to permit persons to whom the
>>> + *     Software is furnished to do so, subject to the following
>>> + *     conditions:
>>> + *
>>> + *     The above copyright notice and this permission notice shall be
>>> + *     included in all copies or substantial portions of the Software.
>>> + *
>>> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
>>> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
>>> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
>>> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
>>> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
>>> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
>>> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
>>> + *     OTHER DEALINGS IN THE SOFTWARE.
>>> +
>>> + */
>>> +
>>> +#include "skeleton.dtsi"
>>> +
>>> +#include <dt-bindings/interrupt-controller/arm-gic.h>
>>> +
>>> +#include <dt-bindings/pinctrl/sun4i-a10.h>
>>> +
>>> +/ {
>>> +     interrupt-parent = <&gic>;
>>> +
>>> +     chosen {
>>> +             #address-cells = <1>;
>>> +             #size-cells = <1>;
>>> +             ranges;
>>> +     };
>>> +
>>> +     cpus {
>>> +             #address-cells = <1>;
>>> +             #size-cells = <0>;
>>> +
>>> +             cpu@0 {
>>> +                     compatible = "arm,cortex-a7";
>>> +                     device_type = "cpu";
>>> +                     reg = <0>;
>>> +             };
>>> +
>>> +             cpu@1 {
>>> +                     compatible = "arm,cortex-a7";
>>> +                     device_type = "cpu";
>>> +                     reg = <1>;
>>> +             };
>>> +
>>> +             cpu@2 {
>>> +                     compatible = "arm,cortex-a7";
>>> +                     device_type = "cpu";
>>> +                     reg = <2>;
>>> +             };
>>> +
>>> +             cpu@3 {
>>> +                     compatible = "arm,cortex-a7";
>>> +                     device_type = "cpu";
>>> +                     reg = <3>;
>>> +             };
>>
>> A \n here please
>>
>>> +             cpu@100 {
>>> +                     compatible = "arm,cortex-a7";
>>> +                     device_type = "cpu";
>>> +                     reg = <0x100>;
>>> +             };
>>> +
>>> +             cpu@101 {
>>> +                     compatible = "arm,cortex-a7";
>>> +                     device_type = "cpu";
>>> +                     reg = <0x101>;
>>> +             };
>>
>> Ditto.
>>
>>> +             cpu@102 {
>>> +                     compatible = "arm,cortex-a7";
>>> +                     device_type = "cpu";
>>> +                     reg = <0x102>;
>>> +             };
>>> +
>>> +             cpu@103 {
>>> +                     compatible = "arm,cortex-a7";
>>> +                     device_type = "cpu";
>>> +                     reg = <0x103>;
>>> +             };
>>> +     };
>>> +
>>> +     memory {
>>> +             reg = <0x40000000 0x80000000>;
>>> +     };
>>
>> Is mainline u-boot usable ? If so, you can remove that node entirely.
>>
>>> +
>>> +     timer {
>>> +             compatible = "arm,armv7-timer";
>>> +             interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
>>> +                          <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
>>> +                          <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
>>> +                          <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
>>> +     };
>>> +
>>> +     clocks {
>>> +             #address-cells = <1>;
>>> +             #size-cells = <1>;
>>> +             ranges;
>>> +
>>> +             osc24M: osc24M_clk {
>>> +                     #clock-cells = <0>;
>>> +                     compatible = "fixed-clock";
>>> +                     clock-frequency = <24000000>;
>>> +                     clock-output-names = "osc24M";
>>> +             };
>>> +
>>> +             osc32k: osc32k_clk {
>>> +                     #clock-cells = <0>;
>>> +                     compatible = "fixed-clock";
>>> +                     clock-frequency = <32768>;
>>> +                     clock-output-names = "osc32k";
>>> +             };
>>
>> Do you need to modify the clocks driver in your first commit then?
>>
>>> +     };
>>> +
>>> +     soc {
>>> +             compatible = "simple-bus";
>>> +             #address-cells = <1>;
>>> +             #size-cells = <1>;
>>> +             ranges;
>>> +
>>> +             gic: interrupt-controller@01c81000 {
>>> +                     compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
>>> +                     reg = <0x01c81000 0x1000>,
>>> +                           <0x01c82000 0x1000>,
>>> +                           <0x01c84000 0x2000>,
>>> +                           <0x01c86000 0x2000>;
>>
>> Please order the nodes by ascending physical addresses.
>>
>>> +                     interrupt-controller;
>>> +                     #interrupt-cells = <3>;
>>> +                     interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
>>> +             };
>>> +
>>> +             pio: pinctrl@01c20800 {
>>> +                     compatible = "allwinner,sun8i-a83t-pinctrl";
>>> +                     interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
>>> +                                  <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
>>> +                                  <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
>>> +                     reg = <0x01c20800 0x400>;
>>> +                     clocks = <&osc24M>;
>>> +                     gpio-controller;
>>> +                     interrupt-controller;
>>> +                     #interrupt-cells = <3>;
>>> +                     #gpio-cells = <3>;
>>> +
>>> +                     mmc0_pins_a: mmc0@0 {
>>> +                             allwinner,pins = "PF0", "PF1", "PF2",
>>> +                                              "PF3", "PF4", "PF5";
>>> +                             allwinner,function = "mmc0";
>>> +                             allwinner,drive = <SUN4I_PINCTRL_30_MA>;
>>> +                             allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>>> +                     };
>>> +
>>> +                     uart0_pins_a: uart0@0 {
>>> +                             allwinner,pins = "PF2", "PF4";
>>> +                             allwinner,function = "uart0";
>>> +                             allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>>> +                             allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>>> +                     };
>
> I don't see much use for the UART0 PF pins once we have mmc working.
>
> ChenYu

I've received my Onda 989 Air based on A83T, I do not find another
UART on it, rather I did not spend enough time to find.

These nodes will help me adding nodes locally everytime I use Onda Air
using microSD Breakout Board,  I request to keep those.
>
>>> +
>>> +                     uart0_pins_b: uart0@1 {
>>> +                             allwinner,pins = "PB9", "PB10";
>>> +                             allwinner,function = "uart0";
>>> +                             allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>>> +                             allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>>> +                     };
>>> +             };
>>> +
>>> +             uart0: serial@01c28000 {
>>> +                     compatible = "snps,dw-apb-uart";
>>> +                     reg = <0x01c28000 0x400>;
>>> +                     interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
>>> +                     reg-shift = <2>;
>>> +                     reg-io-width = <4>;
>>> +                     clocks = <&osc24M>;
>>> +                     status = "disabled";
>>> +             };
>>> +     };
>>> +};
>>
>> Thanks!
>> Maxime
>>
>> --
>> Maxime Ripard, Free Electrons
>> Embedded Linux, Kernel and Android engineering
>> http://free-electrons.com
>
> --
> You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
> To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe@googlegroups.com.
> For more options, visit https://groups.google.com/d/optout.

Re: [PATCH v3 2/3] ARM: dts: sun8i: Add Allwinner A83T dtsi

[Vishnu Patekar]

Hello Maxime,


On Sat, Dec 19, 2015 at 5:41 AM, Maxime Ripard
<maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org> wrote:
> Hi,
>
> On Fri, Dec 18, 2015 at 09:30:50PM +0800, Vishnu Patekar wrote:
>> Allwinner A83T is new octa-core cortex-a7 SOC.
>> This adds the basic dtsi, the clocks differs from
>> earlier sun8i SOCs.
>>
>> Signed-off-by: Vishnu Patekar <vishnupatekar0510-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
>> ---
>>  arch/arm/boot/dts/sun8i-a83t.dtsi | 206 ++++++++++++++++++++++++++++++++++++++
>>  1 file changed, 206 insertions(+)
>>  create mode 100644 arch/arm/boot/dts/sun8i-a83t.dtsi
>>
>> diff --git a/arch/arm/boot/dts/sun8i-a83t.dtsi b/arch/arm/boot/dts/sun8i-a83t.dtsi
>> new file mode 100644
>> index 0000000..e577c64
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/sun8i-a83t.dtsi
>> @@ -0,0 +1,206 @@
>> +/*
>> + * Copyright 2015 Vishnu Patekar
>> + *
>> + * Vishnu Patekar <vishnupatekar0510-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
>> + *
>> + * This file is dual-licensed: you can use it either under the terms
>> + * of the GPL or the X11 license, at your option. Note that this dual
>> + * licensing only applies to this file, and not this project as a
>> + * whole.
>> + *
>> + *  a) This file is free software; you can redistribute it and/or
>> + *     modify it under the terms of the GNU General Public License as
>> + *     published by the Free Software Foundation; either version 2 of the
>> + *     License, or (at your option) any later version.
>> + *
>> + *     This file is distributed in the hope that it will be useful,
>> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> + *     GNU General Public License for more details.
>> + *
>> + * Or, alternatively,
>> + *
>> + *  b) Permission is hereby granted, free of charge, to any person
>> + *     obtaining a copy of this software and associated documentation
>> + *     files (the "Software"), to deal in the Software without
>> + *     restriction, including without limitation the rights to use,
>> + *     copy, modify, merge, publish, distribute, sublicense, and/or
>> + *     sell copies of the Software, and to permit persons to whom the
>> + *     Software is furnished to do so, subject to the following
>> + *     conditions:
>> + *
>> + *     The above copyright notice and this permission notice shall be
>> + *     included in all copies or substantial portions of the Software.
>> + *
>> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
>> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
>> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
>> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
>> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
>> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
>> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
>> + *     OTHER DEALINGS IN THE SOFTWARE.
>> +
>> + */
>> +
>> +#include "skeleton.dtsi"
>> +
>> +#include <dt-bindings/interrupt-controller/arm-gic.h>
>> +
>> +#include <dt-bindings/pinctrl/sun4i-a10.h>
>> +
>> +/ {
>> +     interrupt-parent = <&gic>;
>> +
>> +     chosen {
>> +             #address-cells = <1>;
>> +             #size-cells = <1>;
>> +             ranges;
>> +     };
>> +
>> +     cpus {
>> +             #address-cells = <1>;
>> +             #size-cells = <0>;
>> +
>> +             cpu@0 {
>> +                     compatible = "arm,cortex-a7";
>> +                     device_type = "cpu";
>> +                     reg = <0>;
>> +             };
>> +
>> +             cpu@1 {
>> +                     compatible = "arm,cortex-a7";
>> +                     device_type = "cpu";
>> +                     reg = <1>;
>> +             };
>> +
>> +             cpu@2 {
>> +                     compatible = "arm,cortex-a7";
>> +                     device_type = "cpu";
>> +                     reg = <2>;
>> +             };
>> +
>> +             cpu@3 {
>> +                     compatible = "arm,cortex-a7";
>> +                     device_type = "cpu";
>> +                     reg = <3>;
>> +             };
>
> A \n here please
>
>> +             cpu@100 {
>> +                     compatible = "arm,cortex-a7";
>> +                     device_type = "cpu";
>> +                     reg = <0x100>;
>> +             };
>> +
>> +             cpu@101 {
>> +                     compatible = "arm,cortex-a7";
>> +                     device_type = "cpu";
>> +                     reg = <0x101>;
>> +             };
>
> Ditto.
>
>> +             cpu@102 {
>> +                     compatible = "arm,cortex-a7";
>> +                     device_type = "cpu";
>> +                     reg = <0x102>;
>> +             };
>> +
>> +             cpu@103 {
>> +                     compatible = "arm,cortex-a7";
>> +                     device_type = "cpu";
>> +                     reg = <0x103>;
>> +             };
>> +     };
>> +
>> +     memory {
>> +             reg = <0x40000000 0x80000000>;
>> +     };
>
> Is mainline u-boot usable ? If so, you can remove that node entirely.
Yes, it is usable now. :)
>
>> +
>> +     timer {
>> +             compatible = "arm,armv7-timer";
>> +             interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
>> +                          <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
>> +                          <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
>> +                          <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
>> +     };
>> +
>> +     clocks {
>> +             #address-cells = <1>;
>> +             #size-cells = <1>;
>> +             ranges;
>> +
>> +             osc24M: osc24M_clk {
>> +                     #clock-cells = <0>;
>> +                     compatible = "fixed-clock";
>> +                     clock-frequency = <24000000>;
>> +                     clock-output-names = "osc24M";
>> +             };
>> +
>> +             osc32k: osc32k_clk {
>> +                     #clock-cells = <0>;
>> +                     compatible = "fixed-clock";
>> +                     clock-frequency = <32768>;
>> +                     clock-output-names = "osc32k";
>> +             };
>
> Do you need to modify the clocks driver in your first commit then?
I did not get what you are trying to say here, could you please elaborate?

I'll correct mistakes, and re-send this patch, is it okie?
>
>> +     };
>> +
>> +     soc {
>> +             compatible = "simple-bus";
>> +             #address-cells = <1>;
>> +             #size-cells = <1>;
>> +             ranges;
>> +
>> +             gic: interrupt-controller@01c81000 {
>> +                     compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
>> +                     reg = <0x01c81000 0x1000>,
>> +                           <0x01c82000 0x1000>,
>> +                           <0x01c84000 0x2000>,
>> +                           <0x01c86000 0x2000>;
>
> Please order the nodes by ascending physical addresses.
>
>> +                     interrupt-controller;
>> +                     #interrupt-cells = <3>;
>> +                     interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
>> +             };
>> +
>> +             pio: pinctrl@01c20800 {
>> +                     compatible = "allwinner,sun8i-a83t-pinctrl";
>> +                     interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
>> +                                  <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
>> +                                  <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
>> +                     reg = <0x01c20800 0x400>;
>> +                     clocks = <&osc24M>;
>> +                     gpio-controller;
>> +                     interrupt-controller;
>> +                     #interrupt-cells = <3>;
>> +                     #gpio-cells = <3>;
>> +
>> +                     mmc0_pins_a: mmc0@0 {
>> +                             allwinner,pins = "PF0", "PF1", "PF2",
>> +                                              "PF3", "PF4", "PF5";
>> +                             allwinner,function = "mmc0";
>> +                             allwinner,drive = <SUN4I_PINCTRL_30_MA>;
>> +                             allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> +                     };
>> +
>> +                     uart0_pins_a: uart0@0 {
>> +                             allwinner,pins = "PF2", "PF4";
>> +                             allwinner,function = "uart0";
>> +                             allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> +                             allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> +                     };
>> +
>> +                     uart0_pins_b: uart0@1 {
>> +                             allwinner,pins = "PB9", "PB10";
>> +                             allwinner,function = "uart0";
>> +                             allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> +                             allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> +                     };
>> +             };
>> +
>> +             uart0: serial@01c28000 {
>> +                     compatible = "snps,dw-apb-uart";
>> +                     reg = <0x01c28000 0x400>;
>> +                     interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
>> +                     reg-shift = <2>;
>> +                     reg-io-width = <4>;
>> +                     clocks = <&osc24M>;
>> +                     status = "disabled";
>> +             };
>> +     };
>> +};
>
> Thanks!
> Maxime
>
> --
> Maxime Ripard, Free Electrons
> Embedded Linux, Kernel and Android engineering
> http://free-electrons.com

Re: [PATCH v3 2/3] ARM: dts: sun8i: Add Allwinner A83T dtsi

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 1325 bytes --]

On Tue, Dec 22, 2015 at 05:41:22PM +0800, Vishnu Patekar wrote:
> >> +     clocks {
> >> +             #address-cells = <1>;
> >> +             #size-cells = <1>;
> >> +             ranges;
> >> +
> >> +             osc24M: osc24M_clk {
> >> +                     #clock-cells = <0>;
> >> +                     compatible = "fixed-clock";
> >> +                     clock-frequency = <24000000>;
> >> +                     clock-output-names = "osc24M";
> >> +             };
> >> +
> >> +             osc32k: osc32k_clk {
> >> +                     #clock-cells = <0>;
> >> +                     compatible = "fixed-clock";
> >> +                     clock-frequency = <32768>;
> >> +                     clock-output-names = "osc32k";
> >> +             };
> >
> > Do you need to modify the clocks driver in your first commit then?
> I did not get what you are trying to say here, could you please elaborate?
> 
> I'll correct mistakes, and re-send this patch, is it okie?

In your first patch, you add a CLK_OF_DECLARE for the H3 compatible in
clk-sunxi.c

Judging from your clocks node above, you don't need it at all.

I'm guessing you'll need it later on, but I wanted to know if that was
intentional :)

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[PATCH v3 3/3] ARM: dts: sun8i: Add A83T HomletV2 Board by Allwinner

[Vishnu Patekar]

H8Homlet Proto v2.0 Board is A83T Dev Board by Allwinner.
It has UART, ethernet, USB, HDMI, etc ports on it.

A83T patches are tested on this board.
It has UART, ethernet, USB, HDMI, etc ports on it.

For FEL mode it needs USB A-A(Male) cable. I used uart0 which
is multiplexed to microsd pins PF2 and PF4.

Enabled UART0 Header(PB9, PB10 pins).

Signed-off-by: Vishnu Patekar <vishnupatekar0510-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
 arch/arm/boot/dts/Makefile                         |  1 +
 .../boot/dts/sun8i-a83t-allwinner-h8homlet-v2.dts  | 64 ++++++++++++++++++++++
 2 files changed, 65 insertions(+)
 create mode 100644 arch/arm/boot/dts/sun8i-a83t-allwinner-h8homlet-v2.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index cc7309b..0f81c58 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -662,6 +662,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-a33-ippo-q8h-v1.2.dtb \
 	sun8i-a33-q8-tablet.dtb \
 	sun8i-a33-sinlinx-sina33.dtb \
+	sun8i-a83t-allwinner-h8homlet-v2.dtb \
 	sun8i-h3-orangepi-plus.dtb
 dtb-$(CONFIG_MACH_SUN9I) += \
 	sun9i-a80-optimus.dtb \
diff --git a/arch/arm/boot/dts/sun8i-a83t-allwinner-h8homlet-v2.dts b/arch/arm/boot/dts/sun8i-a83t-allwinner-h8homlet-v2.dts
new file mode 100644
index 0000000..342e1d3
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-a83t-allwinner-h8homlet-v2.dts
@@ -0,0 +1,64 @@
+/*
+ * Copyright 2015 Vishnu Patekar
+ * Vishnu Patekar <vishnupatekar0510-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-a83t.dtsi"
+
+/ {
+	model = "Allwinner A83T H8Homlet Proto Dev Board v2.0";
+	compatible = "allwinner,h8homlet-v2", "allwinner,sun8i-a83t";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_b>;
+	status = "okay";
+};
-- 
1.9.1