[PATCH v2] gpio: pca953x: add PCAL9535 interrupt support for Galileo Gen2

[PATCH v2] gpio: pca953x: add PCAL9535 interrupt support for Galileo Gen2

[Yong Li]

Galileo Gen2 board uses the PCAL9535 as the GPIO expansion,
it is different from PCA9535 and includes interrupt mask/status registers,
The current driver does not support the interrupt registers configuration,
it causes some gpio pins cannot trigger interrupt events,
this patch fix this issue. The original patch was submitted by
Josef Ahmad <josef.ahmad@linux.intel.com>
http://git.yoctoproject.org/cgit/cgit.cgi/meta-intel-quark/tree/recipes-kernel/linux/files/0015-Quark-GPIO-1-2-quark.patch

Signed-off-by: Yong Li <yong.b.li@intel.com>
---
 drivers/gpio/gpio-pca953x.c | 42 +++++++++++++++++++++++++++++++++++++++++-
 1 file changed, 41 insertions(+), 1 deletion(-)

diff --git a/drivers/gpio/gpio-pca953x.c b/drivers/gpio/gpio-pca953x.c
index e66084c..5e3be32 100644
--- a/drivers/gpio/gpio-pca953x.c
+++ b/drivers/gpio/gpio-pca953x.c
@@ -38,8 +38,13 @@
 #define PCA957X_MSK		6
 #define PCA957X_INTS		7
 
+#define PCAL953X_IN_LATCH	34
+#define PCAL953X_INT_MASK	37
+#define PCAL953X_INT_STAT	38
+
 #define PCA_GPIO_MASK		0x00FF
 #define PCA_INT			0x0100
+#define PCA_PCAL			0x0200
 #define PCA953X_TYPE		0x1000
 #define PCA957X_TYPE		0x2000
 #define PCA_TYPE_MASK		0xF000
@@ -77,7 +82,7 @@ static const struct i2c_device_id pca953x_id[] = {
 MODULE_DEVICE_TABLE(i2c, pca953x_id);
 
 static const struct acpi_device_id pca953x_acpi_ids[] = {
-	{ "INT3491", 16 | PCA953X_TYPE | PCA_INT, },
+	{ "INT3491", 16 | PCA953X_TYPE | PCA_INT | PCA_PCAL, },
 	{ }
 };
 MODULE_DEVICE_TABLE(acpi, pca953x_acpi_ids);
@@ -437,6 +442,18 @@ static void pca953x_irq_bus_sync_unlock(struct irq_data *d)
 	struct pca953x_chip *chip = gpiochip_get_data(gc);
 	u8 new_irqs;
 	int level, i;
+	u8 invert_irq_mask[MAX_BANK];
+
+	if (chip->driver_data & PCA_PCAL) {
+		/* Enable latch on interrupt-enabled inputs */
+		pca953x_write_regs(chip, PCAL953X_IN_LATCH, chip->irq_mask);
+
+		for (i = 0; i < NBANK(chip); i++)
+			invert_irq_mask[i] = ~chip->irq_mask[i];
+
+		/* Unmask enabled interrupts */
+		pca953x_write_regs(chip, PCAL953X_INT_MASK, invert_irq_mask);
+	}
 
 	/* Look for any newly setup interrupt */
 	for (i = 0; i < NBANK(chip); i++) {
@@ -498,6 +515,29 @@ static bool pca953x_irq_pending(struct pca953x_chip *chip, u8 *pending)
 	u8 trigger[MAX_BANK];
 	int ret, i, offset = 0;
 
+	if (chip->driver_data & PCA_PCAL) {
+		/* Read the current interrupt status from the device */
+		ret = pca953x_read_regs(chip, PCAL953X_INT_STAT, trigger);
+		if (ret)
+			return false;
+
+		/* Check latched inputs and clear interrupt status */
+		ret = pca953x_read_regs(chip, PCA953X_INPUT, cur_stat);
+		if (ret)
+			return false;
+
+		for (i = 0; i < NBANK(chip); i++) {
+			/* Apply filter for rising/falling edge selection */
+			pending[i] = (~cur_stat[i] & chip->irq_trig_fall[i]) |
+				(cur_stat[i] & chip->irq_trig_raise[i]);
+			pending[i] &= trigger[i];
+			if (pending[i])
+				pending_seen = true;
+		}
+
+		return pending_seen;
+	}
+
 	switch (chip->chip_type) {
 	case PCA953X_TYPE:
 		offset = PCA953X_INPUT;
-- 
2.1.4

Re: [PATCH v2] gpio: pca953x: add PCAL9535 interrupt support for Galileo Gen2

[Andy Shevchenko]

On Thu, 2016-04-07 at 12:56 +0800, Yong Li wrote:
> Galileo Gen2 board uses the PCAL9535 as the GPIO expansion,
> it is different from PCA9535 and includes interrupt mask/status
> registers,
> The current driver does not support the interrupt registers
> configuration,
> it causes some gpio pins cannot trigger interrupt events,
> this patch fix this issue. The original patch was submitted by
> Josef Ahmad <josef.ahmad@linux.intel.com>
> http://git.yoctoproject.org/cgit/cgit.cgi/meta-intel-quark/tree/recipe
> s-kernel/linux/files/0015-Quark-GPIO-1-2-quark.patch
> 

FWIW:
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

> Signed-off-by: Yong Li <yong.b.li@intel.com>
> ---
>  drivers/gpio/gpio-pca953x.c | 42
> +++++++++++++++++++++++++++++++++++++++++-
>  1 file changed, 41 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/gpio/gpio-pca953x.c b/drivers/gpio/gpio-pca953x.c
> index e66084c..5e3be32 100644
> --- a/drivers/gpio/gpio-pca953x.c
> +++ b/drivers/gpio/gpio-pca953x.c
> @@ -38,8 +38,13 @@
>  #define PCA957X_MSK		6
>  #define PCA957X_INTS		7
>  
> +#define PCAL953X_IN_LATCH	34
> +#define PCAL953X_INT_MASK	37
> +#define PCAL953X_INT_STAT	38
> +
>  #define PCA_GPIO_MASK		0x00FF
>  #define PCA_INT			0x0100
> +#define PCA_PCAL			0x0200
>  #define PCA953X_TYPE		0x1000
>  #define PCA957X_TYPE		0x2000
>  #define PCA_TYPE_MASK		0xF000
> @@ -77,7 +82,7 @@ static const struct i2c_device_id pca953x_id[] = {
>  MODULE_DEVICE_TABLE(i2c, pca953x_id);
>  
>  static const struct acpi_device_id pca953x_acpi_ids[] = {
> -	{ "INT3491", 16 | PCA953X_TYPE | PCA_INT, },
> +	{ "INT3491", 16 | PCA953X_TYPE | PCA_INT | PCA_PCAL, },
>  	{ }
>  };
>  MODULE_DEVICE_TABLE(acpi, pca953x_acpi_ids);
> @@ -437,6 +442,18 @@ static void pca953x_irq_bus_sync_unlock(struct
> irq_data *d)
>  	struct pca953x_chip *chip = gpiochip_get_data(gc);
>  	u8 new_irqs;
>  	int level, i;
> +	u8 invert_irq_mask[MAX_BANK];
> +
> +	if (chip->driver_data & PCA_PCAL) {
> +		/* Enable latch on interrupt-enabled inputs */
> +		pca953x_write_regs(chip, PCAL953X_IN_LATCH, chip-
> >irq_mask);
> +
> +		for (i = 0; i < NBANK(chip); i++)
> +			invert_irq_mask[i] = ~chip->irq_mask[i];
> +
> +		/* Unmask enabled interrupts */
> +		pca953x_write_regs(chip, PCAL953X_INT_MASK,
> invert_irq_mask);
> +	}
>  
>  	/* Look for any newly setup interrupt */
>  	for (i = 0; i < NBANK(chip); i++) {
> @@ -498,6 +515,29 @@ static bool pca953x_irq_pending(struct
> pca953x_chip *chip, u8 *pending)
>  	u8 trigger[MAX_BANK];
>  	int ret, i, offset = 0;
>  
> +	if (chip->driver_data & PCA_PCAL) {
> +		/* Read the current interrupt status from the device
> */
> +		ret = pca953x_read_regs(chip, PCAL953X_INT_STAT,
> trigger);
> +		if (ret)
> +			return false;
> +
> +		/* Check latched inputs and clear interrupt status */
> +		ret = pca953x_read_regs(chip, PCA953X_INPUT,
> cur_stat);
> +		if (ret)
> +			return false;
> +
> +		for (i = 0; i < NBANK(chip); i++) {
> +			/* Apply filter for rising/falling edge
> selection */
> +			pending[i] = (~cur_stat[i] & chip-
> >irq_trig_fall[i]) |
> +				(cur_stat[i] & chip-
> >irq_trig_raise[i]);
> +			pending[i] &= trigger[i];
> +			if (pending[i])
> +				pending_seen = true;
> +		}
> +
> +		return pending_seen;
> +	}
> +
>  	switch (chip->chip_type) {
>  	case PCA953X_TYPE:
>  		offset = PCA953X_INPUT;

-- 
Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Intel Finland Oy

--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v2] gpio: pca953x: add PCAL9535 interrupt support for Galileo Gen2

[Linus Walleij]

n Thu, Apr 7, 2016 at 6:56 AM, Yong Li <yong.b.li@intel.com> wrote:

> Galileo Gen2 board uses the PCAL9535 as the GPIO expansion,
> it is different from PCA9535 and includes interrupt mask/status registers,
> The current driver does not support the interrupt registers configuration,
> it causes some gpio pins cannot trigger interrupt events,
> this patch fix this issue. The original patch was submitted by
> Josef Ahmad <josef.ahmad@linux.intel.com>
> http://git.yoctoproject.org/cgit/cgit.cgi/meta-intel-quark/tree/recipes-kernel/linux/files/0015-Quark-GPIO-1-2-quark.patch
>
> Signed-off-by: Yong Li <yong.b.li@intel.com>

Patch applied with Andy's review tag.

Yours,
Linus Walleij

RE: [PATCH v2] gpio: pca953x: add PCAL9535 interrupt support for Galileo Gen2

[Li, Yong B]

Thanks Linus. I think the below patch(in fixes branch) should be merged into devel branch too, since the below patch is depended by this one in devel branch.

commit 9b8e3ec34318663affced3c14d960e78d760dd9a
Author: Yong Li <sdliyong@gmail.com>
Date:   Wed Mar 30 14:49:14 2016 +0800

    gpio: pca953x: Use correct u16 value for register word write

    The current implementation only uses the first byte in val,
    the second byte is always 0. Change it to use cpu_to_le16
    to write the two bytes into the register

    Cc: stable@vger.kernel.org
    Signed-off-by: Yong Li <sdliyong@gmail.com>
    Reviewed-by: Phil Reid <preid@electromag.com.au>
    Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Yong
> -----Original Message-----
> From: Linus Walleij [mailto:linus.walleij@linaro.org]
> Sent: Friday, April 08, 2016 21:21
> To: Li, Yong B <yong.b.li@intel.com>
> Cc: linux-gpio@vger.kernel.org; linux-kernel@vger.kernel.org; Alexandre
> Courbot <gnurou@gmail.com>; Andy Shevchenko
> <andriy.shevchenko@linux.intel.com>; Puustinen, Ismo
> <ismo.puustinen@intel.com>; Phil Reid <preid@electromag.com.au>
> Subject: Re: [PATCH v2] gpio: pca953x: add PCAL9535 interrupt support for
> Galileo Gen2
> 
> n Thu, Apr 7, 2016 at 6:56 AM, Yong Li <yong.b.li@intel.com> wrote:
> 
> > Galileo Gen2 board uses the PCAL9535 as the GPIO expansion, it is
> > different from PCA9535 and includes interrupt mask/status registers,
> > The current driver does not support the interrupt registers
> > configuration, it causes some gpio pins cannot trigger interrupt
> > events, this patch fix this issue. The original patch was submitted by
> > Josef Ahmad <josef.ahmad@linux.intel.com>
> > http://git.yoctoproject.org/cgit/cgit.cgi/meta-intel-quark/tree/recipe
> > s-kernel/linux/files/0015-Quark-GPIO-1-2-quark.patch
> >
> > Signed-off-by: Yong Li <yong.b.li@intel.com>
> 
> Patch applied with Andy's review tag.
> 
> Yours,
> Linus Walleij

Re: [PATCH v2] gpio: pca953x: add PCAL9535 interrupt support for Galileo Gen2

[Linus Walleij]

On Sun, Apr 10, 2016 at 5:02 AM, Li, Yong B <yong.b.li@intel.com> wrote:

> Thanks Linus. I think the below patch(in fixes branch) should be merged into devel branch too, since the below patch is depended by this one in devel branch.
>
> commit 9b8e3ec34318663affced3c14d960e78d760dd9a
> Author: Yong Li <sdliyong@gmail.com>
> Date:   Wed Mar 30 14:49:14 2016 +0800
>
>     gpio: pca953x: Use correct u16 value for register word write

This patch is already upstream so no need to worry about that.

Yours,
Linus Walleij