* [PATCH 02/12] pinctrl: Add core pinctrl support for Aspeed SoCs
2016-07-20 5:58 [PATCH 00/12] aspeed: Add pinctrl and gpio drivers Andrew Jeffery
2016-07-20 5:58 ` [PATCH 01/12] pinctrl: dt-bindings: Add documentation for Aspeed pin controllers Andrew Jeffery
@ 2016-07-20 5:58 ` Andrew Jeffery
2016-07-22 6:29 ` Joel Stanley
2016-08-11 8:41 ` Linus Walleij
2016-07-20 5:58 ` [PATCH 03/12] pinctrl: Add pinctrl-aspeed-g4 driver Andrew Jeffery
` (9 subsequent siblings)
11 siblings, 2 replies; 28+ messages in thread
From: Andrew Jeffery @ 2016-07-20 5:58 UTC (permalink / raw)
To: Linus Walleij
Cc: Mark Rutland, Alexandre Courbot, devicetree, Andrew Jeffery,
Benjamin Herrenschmidt, Russell King, linux-kernel, linux-gpio,
Rob Herring, Joel Stanley, linux-arm-kernel, Jeremy Kerr
The Aspeed SoCs provide typically more than 200 pins for GPIO and other
functions. The signal enabled on a pin is determined on a priority
basis, where a given pin can provide a number of different signal types.
In addition to the priority levels, the Aspeed pin controllers describe
the signal active on a pin by compound logical expressions involving
multiple operators, registers and bits. Some difficulty arises as a
pin's function bit masks for each priority level are frequently not the
same (i.e. we cannot just flip a bit to change from a high to low
priority signal), or even in the same register(s). Some configuration
bits affect multiple pins, while in other cases the signals for a bus
must each be enabled individually.
Together, these features give rise to some complexity in the
implementation. A more complete description of the complexities is
provided in the associated header file in an attempt to justify the
approach.
Note that the patch doesn't implement pinctrl/pinmux/pinconf for any
particular SoC, just adds the framework for defining mux configurations
for any available functions.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
---
MAINTAINERS | 1 +
arch/arm/mach-aspeed/Kconfig | 1 +
drivers/pinctrl/Kconfig | 1 +
drivers/pinctrl/Makefile | 1 +
drivers/pinctrl/aspeed/Kconfig | 8 +
drivers/pinctrl/aspeed/Makefile | 3 +
drivers/pinctrl/aspeed/pinctrl-aspeed.c | 373 +++++++++++++++++++++
drivers/pinctrl/aspeed/pinctrl-aspeed.h | 562 ++++++++++++++++++++++++++++++++
8 files changed, 950 insertions(+)
create mode 100644 drivers/pinctrl/aspeed/Kconfig
create mode 100644 drivers/pinctrl/aspeed/Makefile
create mode 100644 drivers/pinctrl/aspeed/pinctrl-aspeed.c
create mode 100644 drivers/pinctrl/aspeed/pinctrl-aspeed.h
diff --git a/MAINTAINERS b/MAINTAINERS
index b5f2d3576d3a..f6987de35435 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1004,6 +1004,7 @@ F: arch/arm/mach-aspeed/
F: arch/arm/boot/dts/aspeed-*
F: drivers/*/*aspeed*
F: Documentation/devicetree/bindings/*/*aspeed*
+F: drivers/pinctrl/aspeed/
ARM/ATMEL AT91RM9200, AT91SAM9 AND SAMA5 SOC SUPPORT
M: Nicolas Ferre <nicolas.ferre@atmel.com>
diff --git a/arch/arm/mach-aspeed/Kconfig b/arch/arm/mach-aspeed/Kconfig
index 5225fbcb250d..632899c58098 100644
--- a/arch/arm/mach-aspeed/Kconfig
+++ b/arch/arm/mach-aspeed/Kconfig
@@ -5,6 +5,7 @@ menuconfig ARCH_ASPEED
select WATCHDOG
select ASPEED_WATCHDOG
select MOXART_TIMER
+ select PINCTRL
help
Say Y here if you want to run your kernel on an ASpeed BMC SoC.
diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
index fb8200b8e8ec..299e4531f677 100644
--- a/drivers/pinctrl/Kconfig
+++ b/drivers/pinctrl/Kconfig
@@ -232,6 +232,7 @@ config PINCTRL_ZYNQ
help
This selects the pinctrl driver for Xilinx Zynq.
+source "drivers/pinctrl/aspeed/Kconfig"
source "drivers/pinctrl/bcm/Kconfig"
source "drivers/pinctrl/berlin/Kconfig"
source "drivers/pinctrl/freescale/Kconfig"
diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile
index 42a5c1dddfef..161eb5d1d878 100644
--- a/drivers/pinctrl/Makefile
+++ b/drivers/pinctrl/Makefile
@@ -34,6 +34,7 @@ obj-$(CONFIG_PINCTRL_LPC18XX) += pinctrl-lpc18xx.o
obj-$(CONFIG_PINCTRL_TB10X) += pinctrl-tb10x.o
obj-$(CONFIG_PINCTRL_ST) += pinctrl-st.o
obj-$(CONFIG_PINCTRL_ZYNQ) += pinctrl-zynq.o
+obj-$(CONFIG_ARCH_ASPEED) += aspeed/
obj-$(CONFIG_ARCH_BCM) += bcm/
obj-$(CONFIG_PINCTRL_BERLIN) += berlin/
diff --git a/drivers/pinctrl/aspeed/Kconfig b/drivers/pinctrl/aspeed/Kconfig
new file mode 100644
index 000000000000..34d9050f2761
--- /dev/null
+++ b/drivers/pinctrl/aspeed/Kconfig
@@ -0,0 +1,8 @@
+config PINCTRL_ASPEED
+ bool
+ depends on (ARCH_ASPEED || COMPILE_TEST) && OF
+ select PINMUX
+ select PINCONF
+ select GENERIC_PINCONF
+ select MFD_SYSCON
+ select REGMAP_MMIO
diff --git a/drivers/pinctrl/aspeed/Makefile b/drivers/pinctrl/aspeed/Makefile
new file mode 100644
index 000000000000..6bc001c001ee
--- /dev/null
+++ b/drivers/pinctrl/aspeed/Makefile
@@ -0,0 +1,3 @@
+# Aspeed pinctrl support
+
+obj-$(CONFIG_PINCTRL_ASPEED) += pinctrl-aspeed.o
diff --git a/drivers/pinctrl/aspeed/pinctrl-aspeed.c b/drivers/pinctrl/aspeed/pinctrl-aspeed.c
new file mode 100644
index 000000000000..07d09e04a6ed
--- /dev/null
+++ b/drivers/pinctrl/aspeed/pinctrl-aspeed.c
@@ -0,0 +1,373 @@
+/*
+ * Copyright (C) 2016 IBM Corp.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/io.h>
+#include <linux/mfd/syscon.h>
+#include <linux/platform_device.h>
+#include <linux/string.h>
+#include "../core.h"
+#include "pinctrl-aspeed.h"
+
+int aspeed_pinctrl_get_groups_count(struct pinctrl_dev *pctldev)
+{
+ struct aspeed_pinctrl_data *pdata = pinctrl_dev_get_drvdata(pctldev);
+
+ return pdata->ngroups;
+}
+
+const char *aspeed_pinctrl_get_group_name(struct pinctrl_dev *pctldev,
+ unsigned int group)
+{
+ struct aspeed_pinctrl_data *pdata = pinctrl_dev_get_drvdata(pctldev);
+
+ return pdata->groups[group].name;
+}
+
+int aspeed_pinctrl_get_group_pins(struct pinctrl_dev *pctldev,
+ unsigned int group, const unsigned int **pins,
+ unsigned int *npins)
+{
+ struct aspeed_pinctrl_data *pdata = pinctrl_dev_get_drvdata(pctldev);
+
+ *pins = &pdata->groups[group].pins[0];
+ *npins = pdata->groups[group].npins;
+
+ return 0;
+}
+
+void aspeed_pinctrl_pin_dbg_show(struct pinctrl_dev *pctldev,
+ struct seq_file *s, unsigned int offset)
+{
+ seq_printf(s, " %s", dev_name(pctldev->dev));
+}
+
+int aspeed_pinmux_get_fn_count(struct pinctrl_dev *pctldev)
+{
+ struct aspeed_pinctrl_data *pdata = pinctrl_dev_get_drvdata(pctldev);
+
+ return pdata->nfunctions;
+}
+
+const char *aspeed_pinmux_get_fn_name(struct pinctrl_dev *pctldev,
+ unsigned int function)
+{
+ struct aspeed_pinctrl_data *pdata = pinctrl_dev_get_drvdata(pctldev);
+
+ return pdata->functions[function].name;
+}
+
+int aspeed_pinmux_get_fn_groups(struct pinctrl_dev *pctldev,
+ unsigned int function, const char * const **groups,
+ unsigned int * const num_groups)
+{
+ struct aspeed_pinctrl_data *pdata = pinctrl_dev_get_drvdata(pctldev);
+
+ *groups = pdata->functions[function].groups;
+ *num_groups = pdata->functions[function].ngroups;
+
+ return 0;
+}
+
+static inline void aspeed_sig_desc_print_val(
+ const struct aspeed_sig_desc *desc, bool enable, u32 rv)
+{
+#if defined(CONFIG_DEBUG_PINCTRL)
+ pr_debug("SCU%x[0x%08x]=0x%x, got 0x%x from 0x%08x\n", desc->reg,
+ desc->mask, enable ? desc->enable : desc->disable,
+ (rv & desc->mask) >> __ffs(desc->mask), rv);
+#endif
+}
+
+static bool aspeed_sig_desc_eval(const struct aspeed_sig_desc *desc,
+ bool enabled, struct regmap *map)
+{
+ unsigned int raw;
+ u32 want;
+
+ if (regmap_read(map, desc->reg, &raw) < 0)
+ return false;
+
+ aspeed_sig_desc_print_val(desc, enabled, raw);
+ want = enabled ? desc->enable : desc->disable;
+
+ return ((raw & desc->mask) >> __ffs(desc->mask)) == want;
+}
+
+static bool aspeed_sig_expr_eval(const struct aspeed_sig_expr *expr,
+ bool enabled, struct regmap *map)
+{
+ int i;
+
+ for (i = 0; i < expr->ndescs; i++) {
+ const struct aspeed_sig_desc *desc = &expr->descs[i];
+
+ if (!aspeed_sig_desc_eval(desc, enabled, map))
+ return false;
+ }
+
+ return true;
+}
+
+/**
+ * Configure a signal state by applying descriptor state for all descriptors in
+ * a signal expression.
+ *
+ * @expr: The expression associated with the function whose signal is to be
+ * configured
+ * @enable: true to enable an function's signal through a pin's signal
+ * expression, false to disable the function's signal
+ * @map: The SCU's regmap instance for pinmux register access.
+ *
+ * @return true if the expression is configured as requested, false otherwise
+ */
+static bool aspeed_sig_expr_set(const struct aspeed_sig_expr *expr,
+ bool enable, struct regmap *map)
+{
+ int i;
+ bool ret;
+
+ ret = aspeed_sig_expr_eval(expr, enable, map);
+ if (ret)
+ return ret;
+
+ for (i = 0; i < expr->ndescs; i++) {
+ const struct aspeed_sig_desc *desc = &expr->descs[i];
+ u32 pattern = enable ? desc->enable : desc->disable;
+ unsigned int val;
+
+ /*
+ * Strap registers are configured in hardware or by early-boot
+ * firmware. Treat them as read-only despite that we can write
+ * them. This may mean that certain functions cannot be
+ * deconfigured and is the reason we re-evaluate after writing
+ * all descriptor bits.
+ */
+ if (desc->reg == HW_STRAP1 || desc->reg == HW_STRAP2)
+ continue;
+
+ if (regmap_read(map, desc->reg, &val) < 0)
+ return false;
+
+ val &= ~desc->mask;
+ val |= pattern << __ffs(desc->mask);
+
+ if (regmap_write(map, desc->reg, val) < 0)
+ return false;
+ }
+
+ return aspeed_sig_expr_eval(expr, enable, map);
+}
+
+static bool aspeed_sig_expr_enable(const struct aspeed_sig_expr *expr,
+ struct regmap *map)
+{
+ return aspeed_sig_expr_set(expr, true, map);
+}
+
+static bool aspeed_sig_expr_disable(const struct aspeed_sig_expr *expr,
+ struct regmap *map)
+{
+ return aspeed_sig_expr_set(expr, false, map);
+}
+
+/**
+ * Disable a signal on a pin by disabling all provided signal expressions.
+ *
+ * @exprs: The list of signal expressions (from a priority level on a pin)
+ * @map: The SCU's regmap instance for pinmux register access.
+ *
+ * @return true if all expressions in the list are successfully disabled, false
+ * otherwise
+ */
+static bool aspeed_disable_sig(const struct aspeed_sig_expr **exprs,
+ struct regmap *map)
+{
+ bool disabled = true;
+
+ if (!exprs)
+ return true;
+
+ while (*exprs) {
+ bool ret;
+
+ ret = aspeed_sig_expr_disable(*exprs, map);
+ disabled = disabled && ret;
+
+ exprs++;
+ }
+
+ return disabled;
+}
+
+/**
+ * Search for the signal expression needed to enable the pin's signal for the
+ * requested function.
+ *
+ * @exprs: List of signal expressions (haystack)
+ * @name: The name of the requested function (needle)
+ *
+ * @return A pointer to the signal expression whose function tag matches the
+ * provided name, otherwise NULL.
+ *
+ */
+static const struct aspeed_sig_expr *aspeed_find_expr_by_name(
+ const struct aspeed_sig_expr **exprs, const char *name)
+{
+ while (*exprs) {
+ if (strcmp((*exprs)->function, name) == 0)
+ return *exprs;
+ exprs++;
+ }
+
+ return NULL;
+}
+
+int aspeed_pinmux_set_mux(struct pinctrl_dev *pctldev, unsigned int function,
+ unsigned int group)
+{
+ int i;
+ const struct aspeed_pinctrl_data *pdata =
+ pinctrl_dev_get_drvdata(pctldev);
+ const struct aspeed_pin_group *pgroup = &pdata->groups[group];
+ const struct aspeed_pin_function *pfunc =
+ &pdata->functions[function];
+
+ for (i = 0; i < pgroup->npins; i++) {
+ int pin = pgroup->pins[i];
+ const struct aspeed_pin_desc *pdesc = pdata->pins[pin].drv_data;
+ const struct aspeed_sig_expr *expr = NULL;
+ const struct aspeed_sig_expr **funcs;
+ const struct aspeed_sig_expr ***prios;
+
+ if (!pdesc)
+ return -EINVAL;
+
+ prios = pdesc->prios;
+
+ if (!prios)
+ continue;
+
+ /* Disable functions at a higher priority than that requested */
+ while ((funcs = *prios)) {
+ expr = aspeed_find_expr_by_name(funcs, pfunc->name);
+
+ if (expr)
+ break;
+
+ if (!aspeed_disable_sig(funcs, pdata->map))
+ return -EPERM;
+
+ prios++;
+ }
+
+ if (!expr)
+ return -EINVAL;
+
+ if (!aspeed_sig_expr_enable(expr, pdata->map))
+ return -EPERM;
+ }
+
+ return 0;
+}
+
+static bool aspeed_gpio_in_exprs(const struct aspeed_sig_expr **exprs)
+{
+ if (!exprs)
+ return false;
+
+ while (*exprs) {
+ if (strncmp((*exprs)->signal, "GPIO", 4) == 0)
+ return true;
+ exprs++;
+ }
+
+ return false;
+}
+
+int aspeed_gpio_request_enable(struct pinctrl_dev *pctldev,
+ struct pinctrl_gpio_range *range,
+ unsigned int offset)
+{
+ const struct aspeed_pinctrl_data *pdata =
+ pinctrl_dev_get_drvdata(pctldev);
+ const struct aspeed_pin_desc *pdesc = pdata->pins[offset].drv_data;
+ const struct aspeed_sig_expr ***prios, **funcs, *expr;
+
+ if (!pdesc)
+ return -EINVAL;
+
+ prios = pdesc->prios;
+
+ if (!prios)
+ return -ENXIO;
+
+ /* Disable any functions of higher priority than GPIO */
+ while ((funcs = *prios)) {
+ if (aspeed_gpio_in_exprs(funcs))
+ break;
+
+ if (!aspeed_disable_sig(funcs, pdata->map))
+ return -EPERM;
+
+ prios++;
+ }
+
+ /* No GPIO option? */
+ if (!funcs)
+ return -ENXIO;
+
+ expr = *funcs;
+
+ /*
+ * If GPIO is the "Other" case, then disabling all signal expressions
+ * is all that's required. As such it has no associated expression.
+ */
+ if (!expr)
+ return 0;
+
+ /*
+ * Otherwise, assume there is only one expression defined to enable
+ * the GPIO function
+ */
+ if (!aspeed_sig_expr_enable(expr, pdata->map))
+ return -EPERM;
+
+ return 0;
+}
+
+int aspeed_pinctrl_probe(struct platform_device *pdev,
+ struct pinctrl_desc *pdesc,
+ struct aspeed_pinctrl_data *pdata)
+{
+ struct device *parent;
+ struct pinctrl_dev *pctl;
+
+ parent = pdev->dev.parent;
+ if (!parent) {
+ dev_err(&pdev->dev, "No parent for syscon pincontroller\n");
+ return -ENODEV;
+ }
+
+ pdata->map = syscon_node_to_regmap(parent->of_node);
+ if (IS_ERR(pdata->map)) {
+ dev_err(&pdev->dev, "No regmap for syscon pincontroller parent\n");
+ return PTR_ERR(pdata->map);
+ }
+
+ pctl = pinctrl_register(pdesc, &pdev->dev, pdata);
+
+ if (IS_ERR(pctl)) {
+ dev_err(&pdev->dev, "Failed to register pinctrl\n");
+ return PTR_ERR(pctl);
+ }
+
+ platform_set_drvdata(pdev, pdata);
+
+ return 0;
+}
diff --git a/drivers/pinctrl/aspeed/pinctrl-aspeed.h b/drivers/pinctrl/aspeed/pinctrl-aspeed.h
new file mode 100644
index 000000000000..1adb068a58ce
--- /dev/null
+++ b/drivers/pinctrl/aspeed/pinctrl-aspeed.h
@@ -0,0 +1,562 @@
+/*
+ * Copyright (C) 2016 IBM Corp.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef PINCTRL_ASPEED
+#define PINCTRL_ASPEED
+
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/regmap.h>
+
+/*
+ * The ASPEED AST SoCs provide typically more than 200 pins for GPIO and other
+ * functions. The SoC function enabled on a pin is determined on a priority
+ * basis where a given pin can provide a number of different signal types.
+ *
+ * The signal active on a pin is described by both a priority level and
+ * compound logical expressions involving multiple operators, registers and
+ * bits. Some difficulty arises as the pin's function bit masks for each
+ * priority level are frequently not the same (i.e. cannot just flip a bit to
+ * change from a high to low priority signal), or even in the same register.
+ * Further, not all signals can be unmuxed, as some expressions depend on
+ * values in the hardware strapping register (which is treated as read-only).
+ *
+ * SoC Multi-function Pin Expression Examples
+ * ------------------------------------------
+ *
+ * Here are some sample mux configurations from the AST2400 and AST2500
+ * datasheets to illustrate the corner cases, roughly in order of least to most
+ * corner. The signal priorities are in decending order from P0 (highest).
+ *
+ * D6 is a pin with a single function (beside GPIO); a high priority signal
+ * that participates in one function:
+ *
+ * Ball | Default | P0 Signal | P0 Expression | P1 Signal | P1 Expression | Other
+ * -----+---------+-----------+-----------------------------+-----------+---------------+----------
+ * D6 GPIOA0 MAC1LINK SCU80[0]=1 GPIOA0
+ * -----+---------+-----------+-----------------------------+-----------+---------------+----------
+ *
+ * C5 is a multi-signal pin (high and low priority signals). Here we touch
+ * different registers for the different functions that enable each signal:
+ *
+ * -----+---------+-----------+-----------------------------+-----------+---------------+----------
+ * C5 GPIOA4 SCL9 SCU90[22]=1 TIMER5 SCU80[4]=1 GPIOA4
+ * -----+---------+-----------+-----------------------------+-----------+---------------+----------
+ *
+ * E19 is a single-signal pin with two functions that influence the active
+ * signal. In this case both bits have the same meaning - enable a dedicated
+ * LPC reset pin. However it's not always the case that the bits in the
+ * OR-relationship have the same meaning.
+ *
+ * -----+---------+-----------+-----------------------------+-----------+---------------+----------
+ * E19 GPIOB4 LPCRST# SCU80[12]=1 | Strap[14]=1 GPIOB4
+ * -----+---------+-----------+-----------------------------+-----------+---------------+----------
+ *
+ * For example, pin B19 has a low-priority signal that's enabled by two
+ * distinct SoC functions: A specific SIOPBI bit in register SCUA4, and an ACPI
+ * bit in the STRAP register. The ACPI bit configures signals on pins in
+ * addition to B19. Both of the low priority functions as well as the high
+ * priority function must be disabled for GPIOF1 to be used.
+ *
+ * Ball | Default | P0 Signal | P0 Expression | P1 Signal | P1 Expression | Other
+ * -----+---------+-----------+-----------------------------------------+-----------+----------------------------------------+----------
+ * B19 GPIOF1 NDCD4 SCU80[25]=1 SIOPBI# SCUA4[12]=1 | Strap[19]=0 GPIOF1
+ * -----+---------+-----------+-----------------------------------------+-----------+----------------------------------------+----------
+ *
+ * For pin E18, the SoC ANDs the expected state of three bits to determine the
+ * pin's active signal:
+ *
+ * * SCU3C[3]: Enable external SOC reset function
+ * * SCU80[15]: Enable SPICS1# or EXTRST# function pin
+ * * SCU90[31]: Select SPI interface CS# output
+ *
+ * -----+---------+-----------+-----------------------------------------+-----------+----------------------------------------+----------
+ * E18 GPIOB7 EXTRST# SCU3C[3]=1 & SCU80[15]=1 & SCU90[31]=0 SPICS1# SCU3C[3]=1 & SCU80[15]=1 & SCU90[31]=1 GPIOB7
+ * -----+---------+-----------+-----------------------------------------+-----------+----------------------------------------+----------
+ *
+ * (Bits SCU3C[3] and SCU80[15] appear to only be used in the expressions for
+ * selecting the signals on pin E18)
+ *
+ * Pin T5 is a multi-signal pin with a more complex configuration:
+ *
+ * Ball | Default | P0 Signal | P0 Expression | P1 Signal | P1 Expression | Other
+ * -----+---------+-----------+------------------------------+-----------+---------------+----------
+ * T5 GPIOL1 VPIDE SCU90[5:4]!=0 & SCU84[17]=1 NDCD1 SCU84[17]=1 GPIOL1
+ * -----+---------+-----------+------------------------------+-----------+---------------+----------
+ *
+ * The high priority signal configuration is best thought of in terms of its
+ * exploded form, with reference to the SCU90[5:4] bits:
+ *
+ * * SCU90[5:4]=00: disable
+ * * SCU90[5:4]=01: 18 bits (R6/G6/B6) video mode.
+ * * SCU90[5:4]=10: 24 bits (R8/G8/B8) video mode.
+ * * SCU90[5:4]=11: 30 bits (R10/G10/B10) video mode.
+ *
+ * Re-writing:
+ *
+ * -----+---------+-----------+------------------------------+-----------+---------------+----------
+ * T5 GPIOL1 VPIDE (SCU90[5:4]=1 & SCU84[17]=1) NDCD1 SCU84[17]=1 GPIOL1
+ * | (SCU90[5:4]=2 & SCU84[17]=1)
+ * | (SCU90[5:4]=3 & SCU84[17]=1)
+ * -----+---------+-----------+------------------------------+-----------+---------------+----------
+ *
+ * For reference the SCU84[17] bit configure the "UART1 NDCD1 or Video VPIDE
+ * function pin", where the signal itself is determined by whether SCU94[5:4]
+ * is disabled or in one of the 18, 24 or 30bit video modes.
+ *
+ * Other video-input-related pins require an explicit state in SCU90[5:4], e.g.
+ * W1 and U5:
+ *
+ * -----+---------+-----------+------------------------------+-----------+---------------+----------
+ * W1 GPIOL6 VPIB0 SCU90[5:4]=3 & SCU84[22]=1 TXD1 SCU84[22]=1 GPIOL6
+ * U5 GPIOL7 VPIB1 SCU90[5:4]=3 & SCU84[23]=1 RXD1 SCU84[23]=1 GPIOL7
+ * -----+---------+-----------+------------------------------+-----------+---------------+----------
+ *
+ * The examples of T5 and W1 are particularly fertile, as they also demonstrate
+ * that despite operating as part of the video input bus each signal needs to
+ * be enabled individually via it's own SCU84 (in the cases of T5 and W1)
+ * register bit. This is a little crazy if the bus doesn't have optional
+ * signals, but is used to decent effect with some of the UARTs where not all
+ * signals are required. However, this isn't done consistently - UART1 is
+ * enabled on a per-pin basis, and by contrast, all signals for UART6 are
+ * enabled by a single bit.
+ *
+ * Further, the high and low priority signals listed in the table above share
+ * a configuration bit. The VPI signals should operate in concert in a single
+ * function, but the UART signals should retain the ability to be configured
+ * independently. This pushes the implementation down the path of tagging a
+ * signal's expressions with the function they participate in, rather than
+ * defining masks affecting multiple signals per function. The latter approach
+ * fails in this instance where applying the configuration for the UART pin of
+ * interest will stomp on the state of other UART signals when disabling the
+ * VPI functions on the current pin.
+ *
+ * Ball | Default | P0 Signal | P0 Expression | P1 Signal | P1 Expression | Other
+ * -----+------------+-----------+---------------------------+-----------+---------------+------------
+ * A12 RGMII1TXCK GPIOT0 SCUA0[0]=1 RMII1TXEN Strap[6]=0 RGMII1TXCK
+ * B12 RGMII1TXCTL GPIOT1 SCUA0[1]=1 – Strap[6]=0 RGMII1TXCTL
+ * -----+------------+-----------+---------------------------+-----------+---------------+------------
+ *
+ * A12 demonstrates that the "Other" signal isn't always GPIO - in this case
+ * GPIOT0 is a high-priority signal and RGMII1TXCK is Other. Thus, GPIO
+ * should be treated like any other signal type with full function expression
+ * requirements, and not assumed to be the default case. Separately, GPIOT0 and
+ * GPIOT1's signal descriptor bits are distinct, therefore we must iterate all
+ * pins in the function's group to disable the higher-priority signals such
+ * that the signal for the function of interest is correctly enabled.
+ *
+ * Finally, three priority levels aren't always enough; the AST2500 brings with
+ * it 18 pins of five priority levels, however the 18 pins only use three of
+ * the five priority levels.
+ *
+ * Ultimately the requirement to control pins in the examples above drive the
+ * design:
+ *
+ * * Pins provide signals according to functions activated in the mux
+ * configuration
+ *
+ * * Pins provide up to five signal types in a priority order
+ *
+ * * For priorities levels defined on a pin, each priority provides one signal
+ *
+ * * Enabling lower priority signals requires higher priority signals be
+ * disabled
+ *
+ * * A function represents a set of signals; functions are distinct if their
+ * sets of signals are not equal
+ *
+ * * Signals participate in one or more functions
+ *
+ * * A function is described by an expression of one or more signal
+ * descriptors, which compare bit values in a register
+ *
+ * * A signal expression is the smallest set of signal descriptors whose
+ * comparisons must evaluate 'true' for a signal to be enabled on a pin.
+ *
+ * * A function's signal is active on a pin if evaluating all signal
+ * descriptors in the pin's signal expression for the function yields a 'true'
+ * result
+ *
+ * * A signal at a given priority on a given pin is active if any of the
+ * functions in which the signal participates are active, and no higher
+ * priority signal on the pin is active
+ *
+ * * GPIO is configured per-pin
+ *
+ * And so:
+ *
+ * * To disable a signal, any function(s) activating the signal must be
+ * disabled
+ *
+ * * Each pin must know the signal expressions of functions in which it
+ * participates, for the purpose of enabling the Other function. This is done
+ * by deactivating all functions that activate higher priority signals on the
+ * pin.
+ *
+ * As a concrete example:
+ *
+ * * T5 provides three signals types: VPIDE, NDCD1 and GPIO
+ *
+ * * The VPIDE signal participates in 3 functions: VPI18, VPI24 and VPI30
+ *
+ * * The NDCD1 signal participates in just its own NDCD1 function
+ *
+ * * VPIDE is high priority, NDCD1 is low priority, and GPIOL1 is the least
+ * prioritised
+ *
+ * * The prerequisit for activating the NDCD1 signal is that the VPI18, VPI24
+ * and VPI30 functions all be disabled
+ *
+ * * Similarly, all of VPI18, VPI24, VPI30 and NDCD1 functions must be disabled
+ * to provide GPIOL6
+ *
+ * Considerations
+ * --------------
+ *
+ * If pinctrl allows us to allocate a pin we can configure a function without
+ * concern for the function of already allocated pins, if pin groups are
+ * created with respect to the SoC functions in which they participate. This is
+ * intuitive, but it did not feel obvious from the bit/pin relationships.
+ *
+ * Conversely, failing to allocate all pins in a group indicates some bits (as
+ * well as pins) required for the group's configuration will already be in use,
+ * likely in a way that's inconsistent with the requirements of the failed
+ * group.
+ */
+
+/*
+ * The "Multi-function Pins Mapping and Control" table in the SoC datasheet
+ * references registers by the device/offset mnemonic. The register macros
+ * below are named the same way to ease transcription and verification (as
+ * opposed to naming them e.g. PINMUX_CTRL_[0-9]). Further, signal expressions
+ * reference registers beyond those dedicated to pinmux, such as the system
+ * reset control and MAC clock configuration registers. The AST2500 goes a step
+ * further and references registers in the graphics IP block, but that isn't
+ * handled yet.
+ */
+#define SCU3C 0x3C /* System Reset Control/Status Register */
+#define SCU48 0x48 /* MAC Interface Clock Delay Setting */
+#define HW_STRAP1 0x70 /* AST2400 strapping is 33 bits, is split */
+#define SCU80 0x80 /* Multi-function Pin Control #1 */
+#define SCU84 0x84 /* Multi-function Pin Control #2 */
+#define SCU88 0x88 /* Multi-function Pin Control #3 */
+#define SCU8C 0x8C /* Multi-function Pin Control #4 */
+#define SCU90 0x90 /* Multi-function Pin Control #5 */
+#define SCU94 0x94 /* Multi-function Pin Control #6 */
+#define SCUA0 0xA0 /* Multi-function Pin Control #7 */
+#define SCUA4 0xA4 /* Multi-function Pin Control #8 */
+#define SCUA8 0xA8 /* Multi-function Pin Control #9 */
+#define HW_STRAP2 0xD0 /* Strapping */
+
+ /**
+ * A signal descriptor, which describes the register, bits and the
+ * enable/disable values that should be compared or written.
+ *
+ * @reg: The register offset from base in bytes
+ * @mask: The mask to apply to the register. The lowest set bit of the mask is
+ * used to derive the shift value.
+ * @enable: The value that enables the function. Value should be in the LSBs,
+ * not at the position of the mask.
+ * @disable: The value that disables the function. Value should be in the
+ * LSBs, not at the position of the mask.
+ */
+struct aspeed_sig_desc {
+ unsigned int reg;
+ u32 mask;
+ u32 enable;
+ u32 disable;
+};
+
+/**
+ * Describes a signal expression. The expression is evaluated by ANDing the
+ * evaluation of the descriptors.
+ *
+ * @signal: The signal name for the priority level on the pin
+ * @function: The name of the function the signal participates in for the
+ * associated expression
+ * @ndescs: The number of signal descriptors in the expression
+ * @descs: Pointer to an array of signal descriptors that comprise the
+ * function expression
+ */
+struct aspeed_sig_expr {
+ const char *signal;
+ const char *function;
+ int ndescs;
+ const struct aspeed_sig_desc *descs;
+};
+
+/**
+ * A struct capturing the list of expressions enabling signals at each priority
+ * for a given pin. The signal configuration for a priority level is evaluated
+ * by ORing the evaluation of the signal expressions in the respective
+ * priority's list.
+ *
+ * @name: A name for the pin
+ * @prios: A pointer to an array of expression list pointers
+ *
+ */
+struct aspeed_pin_desc {
+ const char *name;
+ const struct aspeed_sig_expr ***prios;
+};
+
+/* Macro hell */
+
+/**
+ * Short-hand macro for describing a configuration enabled by the state of one
+ * bit. The disable value is derived.
+ *
+ * @reg: The signal's associated register, offset from base
+ * @idx: The signal's bit index in the register
+ * @val: The value (0 or 1) that enables the function
+ */
+#define SIG_DESC_BIT(reg, idx, val) \
+ { reg, BIT_MASK(idx), val, (((val) + 1) & 1) }
+
+/**
+ * A further short-hand macro describing a configuration enabled with a set bit.
+ *
+ * @reg: The configuration's associated register, offset from base
+ * @idx: The configuration's bit index in the register
+ */
+#define SIG_DESC_SET(reg, idx) SIG_DESC_BIT(reg, idx, 1)
+
+#define SIG_DESC_LIST_SYM(sig, func) sig_descs_ ## sig ## _ ## func
+#define SIG_DESC_LIST_DECL(sig, func, ...) \
+ static const struct aspeed_sig_desc SIG_DESC_LIST_SYM(sig, func)[] = \
+ { __VA_ARGS__ }
+
+#define SIG_EXPR_SYM(sig, func) sig_expr_ ## sig ## _ ## func
+#define SIG_EXPR_DECL_(sig, func) \
+ static const struct aspeed_sig_expr SIG_EXPR_SYM(sig, func) = \
+ { \
+ .signal = #sig, \
+ .function = #func, \
+ .ndescs = ARRAY_SIZE(SIG_DESC_LIST_SYM(sig, func)), \
+ .descs = &(SIG_DESC_LIST_SYM(sig, func))[0], \
+ }
+
+/**
+ * Declare a signal expression.
+ *
+ * @sig: A macro symbol name for the signal (is subjected to stringification
+ * and token pasting)
+ * @func: The function in which the signal is participating
+ * @...: Signal descriptors that define the signal expression
+ *
+ * For example, the following declares the ROMD8 signal for the ROM16 function:
+ *
+ * SIG_EXPR_DECL(ROMD8, ROM16, SIG_DESC_SET(SCU90, 6));
+ *
+ * And with multiple signal descriptors:
+ *
+ * SIG_EXPR_DECL(ROMD8, ROM16S, SIG_DESC_SET(HW_STRAP1, 4),
+ * { HW_STRAP1, GENMASK(1, 0), 0, 0 });
+ */
+#define SIG_EXPR_DECL(sig, func, ...) \
+ SIG_DESC_LIST_DECL(sig, func, __VA_ARGS__); \
+ SIG_EXPR_DECL_(sig, func)
+
+/**
+ * Declare a pointer to a signal expression
+ *
+ * @sig: The macro symbol name for the signal (subjected to token pasting)
+ * @func: The macro symbol name for the function (subjected to token pasting)
+ */
+#define SIG_EXPR_PTR(sig, func) (&SIG_EXPR_SYM(sig, func))
+
+#define SIG_EXPR_LIST_SYM(sig) sig_exprs_ ## sig
+
+/**
+ * Declare a signal expression list for reference in a struct aspeed_pin_prio.
+ *
+ * @sig: A macro symbol name for the signal (is subjected to token pasting)
+ * @...: Signal expression structure pointers (use SIG_EXPR_PTR())
+ *
+ * For example, the 16-bit ROM bus can be enabled by one of two possible signal
+ * expressions:
+ *
+ * SIG_EXPR_DECL(ROMD8, ROM16, SIG_DESC_SET(SCU90, 6));
+ * SIG_EXPR_DECL(ROMD8, ROM16S, SIG_DESC_SET(HW_STRAP1, 4),
+ * { HW_STRAP1, GENMASK(1, 0), 0, 0 });
+ * SIG_EXPR_LIST_DECL(ROMD8, SIG_EXPR_PTR(ROMD8, ROM16),
+ * SIG_EXPR_PTR(ROMD8, ROM16S));
+ */
+#define SIG_EXPR_LIST_DECL(sig, ...) \
+ static const struct aspeed_sig_expr *SIG_EXPR_LIST_SYM(sig)[] = \
+ { __VA_ARGS__, NULL }
+
+/**
+ * A short-hand macro for declaring a function expression and an expression
+ * list with a single function.
+ *
+ * @func: A macro symbol name for the function (is subjected to token pasting)
+ * @...: Function descriptors that define the function expression
+ *
+ * For example, signal NCTS6 participates in its own function with one group:
+ *
+ * SIG_EXPR_LIST_DECL_SINGLE(NCTS6, NCTS6, SIG_DESC_SET(SCU90, 7));
+ */
+#define SIG_EXPR_LIST_DECL_SINGLE(sig, func, ...) \
+ SIG_DESC_LIST_DECL(sig, func, __VA_ARGS__); \
+ SIG_EXPR_DECL_(sig, func); \
+ SIG_EXPR_LIST_DECL(sig, SIG_EXPR_PTR(sig, func))
+
+#define SIG_EXPR_LIST_DECL_DUAL(sig, f0, f1) \
+ SIG_EXPR_LIST_DECL(sig, SIG_EXPR_PTR(sig, f0), SIG_EXPR_PTR(sig, f1))
+
+#define SIG_EXPR_LIST_PTR(sig) (&SIG_EXPR_LIST_SYM(sig)[0])
+
+#define PIN_EXPRS_SYM(pin) pin_exprs_ ## pin
+#define PIN_EXPRS_PTR(pin) (&PIN_EXPRS_SYM(pin)[0])
+#define PIN_SYM(pin) pin_ ## pin
+
+#define MS_PIN_DECL_(pin, ...) \
+ static const struct aspeed_sig_expr **PIN_EXPRS_SYM(pin)[] = \
+ { __VA_ARGS__, NULL }; \
+ static const struct aspeed_pin_desc PIN_SYM(pin) = \
+ { #pin, PIN_EXPRS_PTR(pin) }
+
+/**
+ * Declare a multi-signal pin
+ *
+ * @pin: The pin number
+ * @other: Macro name for "other" functionality (subjected to stringification)
+ * @high: Macro name for the highest priority signal functions
+ * @low: Macro name for the low signal functions
+ *
+ * For example:
+ *
+ * #define A8 56
+ * SIG_EXPR_DECL(ROMD8, ROM16, SIG_DESC_SET(SCU90, 6));
+ * SIG_EXPR_DECL(ROMD8, ROM16S, SIG_DESC_SET(HW_STRAP1, 4),
+ * { HW_STRAP1, GENMASK(1, 0), 0, 0 });
+ * SIG_EXPR_LIST_DECL(ROMD8, SIG_EXPR_PTR(ROMD8, ROM16),
+ * SIG_EXPR_PTR(ROMD8, ROM16S));
+ * SIG_EXPR_LIST_DECL_SINGLE(NCTS6, NCTS6, SIG_DESC_SET(SCU90, 7));
+ * MS_PIN_DECL(A8, GPIOH0, ROMD8, NCTS6);
+ */
+#define MS_PIN_DECL(pin, other, high, low) \
+ SIG_EXPR_LIST_DECL_SINGLE(other, other); \
+ MS_PIN_DECL_(pin, \
+ SIG_EXPR_LIST_PTR(high), \
+ SIG_EXPR_LIST_PTR(low), \
+ SIG_EXPR_LIST_PTR(other))
+
+#define PIN_GROUP_SYM(func) pins_ ## func
+#define FUNC_GROUP_SYM(func) groups_ ## func
+#define FUNC_GROUP_DECL(func, ...) \
+ static const int PIN_GROUP_SYM(func)[] = { __VA_ARGS__ }; \
+ static const char *const FUNC_GROUP_SYM(func)[] = { #func }
+
+/**
+ * Declare a single signal pin
+ *
+ * @pin: The pin number
+ * @other: Macro name for "other" functionality (subjected to stringification)
+ * @sig: Macro name for the signal (subjected to stringification)
+ *
+ * For example:
+ *
+ * #define E3 80
+ * SIG_EXPR_LIST_DECL_SINGLE(SCL5, I2C5, I2C5_DESC);
+ * SS_PIN_DECL(E3, GPIOK0, SCL5);
+ */
+#define SS_PIN_DECL(pin, other, sig) \
+ SIG_EXPR_LIST_DECL_SINGLE(other, other); \
+ MS_PIN_DECL_(pin, SIG_EXPR_LIST_PTR(sig), SIG_EXPR_LIST_PTR(other))
+
+/**
+ * Single signal, single function pin declaration
+ *
+ * @pin: The pin number
+ * @other: Macro name for "other" functionality (subjected to stringification)
+ * @sig: Macro name for the signal (subjected to stringification)
+ * @...: Signal descriptors that define the function expression
+ *
+ * For example:
+ *
+ * SSSF_PIN_DECL(A4, GPIOA2, TIMER3, SIG_DESC_SET(SCU80, 2));
+ */
+#define SSSF_PIN_DECL(pin, other, sig, ...) \
+ SIG_EXPR_LIST_DECL_SINGLE(sig, sig, __VA_ARGS__); \
+ SIG_EXPR_LIST_DECL_SINGLE(other, other); \
+ MS_PIN_DECL_(pin, SIG_EXPR_LIST_PTR(sig), SIG_EXPR_LIST_PTR(other)); \
+ FUNC_GROUP_DECL(sig, pin)
+
+struct aspeed_pinctrl_data {
+ struct regmap *map;
+
+ const struct pinctrl_pin_desc *pins;
+ const unsigned int npins;
+
+ const struct aspeed_pin_group *groups;
+ const unsigned int ngroups;
+
+ const struct aspeed_pin_function *functions;
+ const unsigned int nfunctions;
+};
+
+#define ASPEED_PINCTRL_PIN(name_) \
+ [name_] = { \
+ .number = name_, \
+ .name = #name_, \
+ .drv_data = (void *) &(PIN_SYM(name_)) \
+ }
+
+struct aspeed_pin_group {
+ const char *name;
+ const unsigned int *pins;
+ const unsigned int npins;
+};
+
+#define ASPEED_PINCTRL_GROUP(name_) { \
+ .name = #name_, \
+ .pins = &(PIN_GROUP_SYM(name_))[0], \
+ .npins = ARRAY_SIZE(PIN_GROUP_SYM(name_)), \
+}
+
+struct aspeed_pin_function {
+ const char *name;
+ const char *const *groups;
+ unsigned int ngroups;
+};
+
+#define ASPEED_PINCTRL_FUNC(name_, ...) { \
+ .name = #name_, \
+ .groups = &FUNC_GROUP_SYM(name_)[0], \
+ .ngroups = ARRAY_SIZE(FUNC_GROUP_SYM(name_)), \
+}
+
+int aspeed_pinctrl_get_groups_count(struct pinctrl_dev *pctldev);
+const char *aspeed_pinctrl_get_group_name(struct pinctrl_dev *pctldev,
+ unsigned int group);
+int aspeed_pinctrl_get_group_pins(struct pinctrl_dev *pctldev,
+ unsigned int group, const unsigned int **pins,
+ unsigned int *npins);
+void aspeed_pinctrl_pin_dbg_show(struct pinctrl_dev *pctldev,
+ struct seq_file *s, unsigned int offset);
+int aspeed_pinmux_get_fn_count(struct pinctrl_dev *pctldev);
+const char *aspeed_pinmux_get_fn_name(struct pinctrl_dev *pctldev,
+ unsigned int function);
+int aspeed_pinmux_get_fn_groups(struct pinctrl_dev *pctldev,
+ unsigned int function, const char * const **groups,
+ unsigned int * const num_groups);
+int aspeed_pinmux_set_mux(struct pinctrl_dev *pctldev, unsigned int function,
+ unsigned int group);
+int aspeed_gpio_request_enable(struct pinctrl_dev *pctldev,
+ struct pinctrl_gpio_range *range,
+ unsigned int offset);
+int aspeed_pinctrl_probe(struct platform_device *pdev,
+ struct pinctrl_desc *pdesc,
+ struct aspeed_pinctrl_data *pdata);
+
+#endif /* PINCTRL_ASPEED */
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 28+ messages in thread* [PATCH 03/12] pinctrl: Add pinctrl-aspeed-g4 driver
2016-07-20 5:58 [PATCH 00/12] aspeed: Add pinctrl and gpio drivers Andrew Jeffery
2016-07-20 5:58 ` [PATCH 01/12] pinctrl: dt-bindings: Add documentation for Aspeed pin controllers Andrew Jeffery
2016-07-20 5:58 ` [PATCH 02/12] pinctrl: Add core pinctrl support for Aspeed SoCs Andrew Jeffery
@ 2016-07-20 5:58 ` Andrew Jeffery
2016-07-20 5:58 ` [PATCH 04/12] pinctrl: Add pinctrl-aspeed-g5 driver Andrew Jeffery
` (8 subsequent siblings)
11 siblings, 0 replies; 28+ messages in thread
From: Andrew Jeffery @ 2016-07-20 5:58 UTC (permalink / raw)
To: Linus Walleij
Cc: Mark Rutland, Alexandre Courbot, devicetree, Andrew Jeffery,
Benjamin Herrenschmidt, Russell King, linux-kernel, linux-gpio,
Rob Herring, Joel Stanley, linux-arm-kernel, Jeremy Kerr
A subset of the pins and functions are exposed. The selection of
functions and pins is driven by the development of OpenBMC[1] on the
AST2400 SoC, particularly around booting the OpenPOWER Palmetto
development machine.
[1] https://github.com/openbmc/docs
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
---
arch/arm/mach-aspeed/Kconfig | 1 +
drivers/pinctrl/aspeed/Kconfig | 8 +
drivers/pinctrl/aspeed/Makefile | 1 +
drivers/pinctrl/aspeed/pinctrl-aspeed-g4.c | 1091 ++++++++++++++++++++++++++++
4 files changed, 1101 insertions(+)
create mode 100644 drivers/pinctrl/aspeed/pinctrl-aspeed-g4.c
diff --git a/arch/arm/mach-aspeed/Kconfig b/arch/arm/mach-aspeed/Kconfig
index 632899c58098..2589b90b0a7b 100644
--- a/arch/arm/mach-aspeed/Kconfig
+++ b/arch/arm/mach-aspeed/Kconfig
@@ -15,6 +15,7 @@ config MACH_ASPEED_G4
bool "Aspeed SoC 4th Generation"
depends on ARCH_MULTI_V5
select CPU_ARM926T
+ select PINCTRL_ASPEED_G4
help
Say yes if you intend to run on an Aspeed ast2400 or similar
fourth generation BMCs, such as those used by OpenPower Power8
diff --git a/drivers/pinctrl/aspeed/Kconfig b/drivers/pinctrl/aspeed/Kconfig
index 34d9050f2761..480a206c69f1 100644
--- a/drivers/pinctrl/aspeed/Kconfig
+++ b/drivers/pinctrl/aspeed/Kconfig
@@ -6,3 +6,11 @@ config PINCTRL_ASPEED
select GENERIC_PINCONF
select MFD_SYSCON
select REGMAP_MMIO
+
+config PINCTRL_ASPEED_G4
+ bool "Aspeed AST G4 SoC pin control"
+ depends on (MACH_ASPEED_G4 || COMPILE_TEST) && OF
+ select PINCTRL_ASPEED
+ help
+ Say Y here to enable pin controller support for Aspeed's 4th
+ generation AST SoCs. GPIO is provided by a separate GPIO driver.
diff --git a/drivers/pinctrl/aspeed/Makefile b/drivers/pinctrl/aspeed/Makefile
index 6bc001c001ee..253bddd1fc2d 100644
--- a/drivers/pinctrl/aspeed/Makefile
+++ b/drivers/pinctrl/aspeed/Makefile
@@ -1,3 +1,4 @@
# Aspeed pinctrl support
obj-$(CONFIG_PINCTRL_ASPEED) += pinctrl-aspeed.o
+obj-$(CONFIG_PINCTRL_ASPEED_G4) += pinctrl-aspeed-g4.o
diff --git a/drivers/pinctrl/aspeed/pinctrl-aspeed-g4.c b/drivers/pinctrl/aspeed/pinctrl-aspeed-g4.c
new file mode 100644
index 000000000000..84f95a6ab8d1
--- /dev/null
+++ b/drivers/pinctrl/aspeed/pinctrl-aspeed-g4.c
@@ -0,0 +1,1091 @@
+/*
+ * Copyright (C) 2016 IBM Corp.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/bitops.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/string.h>
+#include <linux/types.h>
+
+#include "../core.h"
+#include "../pinctrl-utils.h"
+#include "pinctrl-aspeed.h"
+
+/*
+ * Uses undefined macros for symbol naming and references, eg GPIOA0, MAC1LINK,
+ * TIMER3 etc.
+ *
+ * Pins are defined in GPIO bank order:
+ *
+ * GPIOA0: 0
+ * ...
+ * GPIOA7: 7
+ * GPIOB0: 8
+ * ...
+ * GPIOZ7: 207
+ * GPIOAA0: 208
+ * ...
+ * GPIOAB3: 219
+ *
+ * Not all pins have their signals defined (yet).
+ */
+
+#define A4 2
+SSSF_PIN_DECL(A4, GPIOA2, TIMER3, SIG_DESC_SET(SCU80, 2));
+
+#define I2C9_DESC SIG_DESC_SET(SCU90, 22)
+
+#define C5 4
+SIG_EXPR_LIST_DECL_SINGLE(SCL9, I2C9, I2C9_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(TIMER5, TIMER5, SIG_DESC_SET(SCU80, 4));
+MS_PIN_DECL(C5, GPIOA4, SCL9, TIMER5);
+
+FUNC_GROUP_DECL(TIMER5, C5);
+
+#define B4 5
+SIG_EXPR_LIST_DECL_SINGLE(SDA9, I2C9, I2C9_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(TIMER6, TIMER6, SIG_DESC_SET(SCU80, 5));
+MS_PIN_DECL(B4, GPIOA5, SDA9, TIMER6);
+
+FUNC_GROUP_DECL(TIMER6, B4);
+FUNC_GROUP_DECL(I2C9, C5, B4);
+
+#define MDIO2_DESC SIG_DESC_SET(SCU90, 2)
+
+#define A3 6
+SIG_EXPR_LIST_DECL_SINGLE(MDC2, MDIO2, MDIO2_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(TIMER7, TIMER7, SIG_DESC_SET(SCU80, 6));
+MS_PIN_DECL(A3, GPIOA6, MDC2, TIMER7);
+
+FUNC_GROUP_DECL(TIMER7, A3);
+
+#define D5 7
+SIG_EXPR_LIST_DECL_SINGLE(MDIO2, MDIO2, MDIO2_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(TIMER8, TIMER8, SIG_DESC_SET(SCU80, 7));
+MS_PIN_DECL(D5, GPIOA7, MDIO2, TIMER8);
+
+FUNC_GROUP_DECL(TIMER8, D5);
+FUNC_GROUP_DECL(MDIO2, A3, D5);
+
+#define H19 13
+#define H19_DESC SIG_DESC_SET(SCU80, 13)
+SIG_EXPR_LIST_DECL_SINGLE(LPCPD, LPCPD, H19_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(LPCSMI, LPCSMI, H19_DESC);
+MS_PIN_DECL(H19, GPIOB5, LPCPD, LPCSMI);
+
+FUNC_GROUP_DECL(LPCPD, H19);
+FUNC_GROUP_DECL(LPCSMI, H19);
+
+#define H20 14
+SSSF_PIN_DECL(H20, GPIOB6, LPCPME, SIG_DESC_SET(SCU80, 14));
+
+#define SD1_DESC SIG_DESC_SET(SCU90, 0)
+#define I2C10_DESC SIG_DESC_SET(SCU90, 23)
+
+#define C4 16
+SIG_EXPR_LIST_DECL_SINGLE(SD1CLK, SD1, SD1_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(SCL10, I2C10, I2C10_DESC);
+MS_PIN_DECL(C4, GPIOC0, SD1CLK, SCL10);
+
+#define B3 17
+SIG_EXPR_LIST_DECL_SINGLE(SD1CMD, SD1, SD1_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(SDA10, I2C10, I2C10_DESC);
+MS_PIN_DECL(B3, GPIOC1, SD1CMD, SDA10);
+
+FUNC_GROUP_DECL(I2C10, C4, B3);
+
+#define I2C11_DESC SIG_DESC_SET(SCU90, 24)
+
+#define A2 18
+SIG_EXPR_LIST_DECL_SINGLE(SD1DAT0, SD1, SD1_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(SCL11, I2C11, I2C11_DESC);
+MS_PIN_DECL(A2, GPIOC2, SD1DAT0, SCL11);
+
+#define E5 19
+SIG_EXPR_LIST_DECL_SINGLE(SD1DAT1, SD1, SD1_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(SDA11, I2C11, I2C11_DESC);
+MS_PIN_DECL(E5, GPIOC3, SD1DAT1, SDA11);
+
+FUNC_GROUP_DECL(I2C11, A2, E5);
+
+#define I2C12_DESC SIG_DESC_SET(SCU90, 25)
+
+#define D4 20
+SIG_EXPR_LIST_DECL_SINGLE(SD1DAT2, SD1, SD1_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(SCL12, I2C12, I2C12_DESC);
+MS_PIN_DECL(D4, GPIOC4, SD1DAT2, SCL12);
+
+#define C3 21
+SIG_EXPR_LIST_DECL_SINGLE(SD1DAT3, SD1, SD1_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(SDA12, I2C12, I2C12_DESC);
+MS_PIN_DECL(C3, GPIOC5, SD1DAT3, SDA12);
+
+FUNC_GROUP_DECL(I2C12, D4, C3);
+
+#define I2C13_DESC SIG_DESC_SET(SCU90, 26)
+
+#define B2 22
+SIG_EXPR_LIST_DECL_SINGLE(SD1CD, SD1, SD1_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(SCL13, I2C13, I2C13_DESC);
+MS_PIN_DECL(B2, GPIOC6, SD1CD, SCL13);
+
+#define A1 23
+SIG_EXPR_LIST_DECL_SINGLE(SD1WP, SD1, SD1_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(SDA13, I2C13, I2C13_DESC);
+MS_PIN_DECL(A1, GPIOC7, SD1WP, SDA13);
+
+FUNC_GROUP_DECL(I2C13, B2, A1);
+FUNC_GROUP_DECL(SD1, C4, B3, A2, E5, D4, C3, B2, A1);
+
+#define SD2_DESC SIG_DESC_SET(SCU90, 1)
+#define GPID_DESC SIG_DESC_SET(HW_STRAP1, 21)
+#define GPID0_DESC SIG_DESC_SET(SCU8C, 8)
+
+#define A18 24
+SIG_EXPR_LIST_DECL_SINGLE(SD2CLK, SD2, SD2_DESC);
+SIG_EXPR_DECL(GPID0IN, GPID0, GPID0_DESC);
+SIG_EXPR_DECL(GPID0IN, GPID, GPID_DESC);
+SIG_EXPR_LIST_DECL_DUAL(GPID0IN, GPID0, GPID);
+MS_PIN_DECL(A18, GPIOD0, SD2CLK, GPID0IN);
+
+#define D16 25
+SIG_EXPR_LIST_DECL_SINGLE(SD2CMD, SD2, SD2_DESC);
+SIG_EXPR_DECL(GPID0OUT, GPID0, GPID0_DESC);
+SIG_EXPR_DECL(GPID0OUT, GPID, GPID_DESC);
+SIG_EXPR_LIST_DECL_DUAL(GPID0OUT, GPID0, GPID);
+MS_PIN_DECL(D16, GPIOD1, SD2CMD, GPID0OUT);
+
+FUNC_GROUP_DECL(GPID0, A18, D16);
+
+#define GPIE_DESC SIG_DESC_SET(HW_STRAP1, 22)
+#define GPIE0_DESC SIG_DESC_SET(SCU8C, 12)
+
+#define D15 32
+SIG_EXPR_LIST_DECL_SINGLE(NCTS3, NCTS3, SIG_DESC_SET(SCU80, 16));
+SIG_EXPR_DECL(GPIE0IN, GPIE0, GPIE0_DESC);
+SIG_EXPR_DECL(GPIE0IN, GPIE, GPIE_DESC);
+SIG_EXPR_LIST_DECL_DUAL(GPIE0IN, GPIE0, GPIE);
+MS_PIN_DECL(D15, GPIOE0, NCTS3, GPIE0IN);
+
+FUNC_GROUP_DECL(NCTS3, D15);
+
+#define C15 33
+SIG_EXPR_LIST_DECL_SINGLE(NDCD3, NDCD3, SIG_DESC_SET(SCU80, 17));
+SIG_EXPR_DECL(GPIE0OUT, GPIE0, GPIE0_DESC);
+SIG_EXPR_DECL(GPIE0OUT, GPIE, GPIE_DESC);
+SIG_EXPR_LIST_DECL_DUAL(GPIE0OUT, GPIE0, GPIE);
+MS_PIN_DECL(C15, GPIOE1, NDCD3, GPIE0OUT);
+
+FUNC_GROUP_DECL(NDCD3, C15);
+FUNC_GROUP_DECL(GPIE0, D15, C15);
+
+#define D18 40
+SSSF_PIN_DECL(D18, GPIOF0, NCTS4, SIG_DESC_SET(SCU80, 24));
+
+#define ACPI_DESC SIG_DESC_BIT(HW_STRAP1, 19, 0)
+
+#define B19 41
+SIG_EXPR_LIST_DECL_SINGLE(NDCD4, NDCD4, SIG_DESC_SET(SCU80, 25));
+SIG_EXPR_DECL(SIOPBI, SIOPBI, SIG_DESC_SET(SCUA4, 12));
+SIG_EXPR_DECL(SIOPBI, ACPI, ACPI_DESC);
+SIG_EXPR_LIST_DECL_DUAL(SIOPBI, SIOPBI, ACPI);
+MS_PIN_DECL(B19, GPIOF1, NDCD4, SIOPBI);
+FUNC_GROUP_DECL(NDCD4, B19);
+FUNC_GROUP_DECL(SIOPBI, B19);
+
+#define D17 43
+SIG_EXPR_LIST_DECL_SINGLE(NRI4, NRI4, SIG_DESC_SET(SCU80, 27));
+SIG_EXPR_DECL(SIOPBO, SIOPBO, SIG_DESC_SET(SCUA4, 14));
+SIG_EXPR_DECL(SIOPBO, ACPI, ACPI_DESC);
+SIG_EXPR_LIST_DECL_DUAL(SIOPBO, SIOPBO, ACPI);
+MS_PIN_DECL(D17, GPIOF3, NRI4, SIOPBO);
+FUNC_GROUP_DECL(NRI4, D17);
+FUNC_GROUP_DECL(SIOPBO, D17);
+
+FUNC_GROUP_DECL(ACPI, B19, D17);
+
+#define E16 46
+SSSF_PIN_DECL(E16, GPIOF6, TXD4, SIG_DESC_SET(SCU80, 30));
+
+#define C17 47
+SSSF_PIN_DECL(C17, GPIOF7, RXD4, SIG_DESC_SET(SCU80, 31));
+
+#define AA22 54
+SSSF_PIN_DECL(AA22, GPIOG6, FLBUSY, SIG_DESC_SET(SCU84, 6));
+
+#define U18 55
+SSSF_PIN_DECL(U18, GPIOG7, FLWP, SIG_DESC_SET(SCU84, 7));
+
+#define UART6_DESC SIG_DESC_SET(SCU90, 7)
+#define ROM16_DESC SIG_DESC_SET(SCU90, 6)
+#define FLASH_WIDE SIG_DESC_SET(HW_STRAP1, 4)
+#define BOOT_SRC_NOR { HW_STRAP1, GENMASK(1, 0), 0, 0 }
+
+#define A8 56
+SIG_EXPR_DECL(ROMD8, ROM16, ROM16_DESC);
+SIG_EXPR_DECL(ROMD8, ROM16S, FLASH_WIDE, BOOT_SRC_NOR);
+SIG_EXPR_LIST_DECL_DUAL(ROMD8, ROM16, ROM16S);
+SIG_EXPR_LIST_DECL_SINGLE(NCTS6, NCTS6, UART6_DESC);
+MS_PIN_DECL(A8, GPIOH0, ROMD8, NCTS6);
+
+#define C7 57
+SIG_EXPR_DECL(ROMD9, ROM16, ROM16_DESC);
+SIG_EXPR_DECL(ROMD9, ROM16S, FLASH_WIDE, BOOT_SRC_NOR);
+SIG_EXPR_LIST_DECL_DUAL(ROMD9, ROM16, ROM16S);
+SIG_EXPR_LIST_DECL_SINGLE(NDCD6, NDCD6, UART6_DESC);
+MS_PIN_DECL(C7, GPIOH1, ROMD9, NDCD6);
+
+#define B7 58
+SIG_EXPR_DECL(ROMD10, ROM16, ROM16_DESC);
+SIG_EXPR_DECL(ROMD10, ROM16S, FLASH_WIDE, BOOT_SRC_NOR);
+SIG_EXPR_LIST_DECL_DUAL(ROMD10, ROM16, ROM16S);
+SIG_EXPR_LIST_DECL_SINGLE(NDSR6, NDSR6, UART6_DESC);
+MS_PIN_DECL(B7, GPIOH2, ROMD10, NDSR6);
+
+#define A7 59
+SIG_EXPR_DECL(ROMD11, ROM16, ROM16_DESC);
+SIG_EXPR_DECL(ROMD11, ROM16S, FLASH_WIDE, BOOT_SRC_NOR);
+SIG_EXPR_LIST_DECL_DUAL(ROMD11, ROM16, ROM16S);
+SIG_EXPR_LIST_DECL_SINGLE(NRI6, NRI6, UART6_DESC);
+MS_PIN_DECL(A7, GPIOH3, ROMD11, NRI6);
+
+#define D7 60
+SIG_EXPR_DECL(ROMD12, ROM16, ROM16_DESC);
+SIG_EXPR_DECL(ROMD12, ROM16S, FLASH_WIDE, BOOT_SRC_NOR);
+SIG_EXPR_LIST_DECL_DUAL(ROMD12, ROM16, ROM16S);
+SIG_EXPR_LIST_DECL_SINGLE(NDTR6, NDTR6, UART6_DESC);
+MS_PIN_DECL(D7, GPIOH4, ROMD12, NDTR6);
+
+#define B6 61
+SIG_EXPR_DECL(ROMD13, ROM16, ROM16_DESC);
+SIG_EXPR_DECL(ROMD13, ROM16S, FLASH_WIDE, BOOT_SRC_NOR);
+SIG_EXPR_LIST_DECL_DUAL(ROMD13, ROM16, ROM16S);
+SIG_EXPR_LIST_DECL_SINGLE(NRTS6, NRTS6, UART6_DESC);
+MS_PIN_DECL(B6, GPIOH5, ROMD13, NRTS6);
+
+#define A6 62
+SIG_EXPR_DECL(ROMD14, ROM16, ROM16_DESC);
+SIG_EXPR_DECL(ROMD14, ROM16S, FLASH_WIDE, BOOT_SRC_NOR);
+SIG_EXPR_LIST_DECL_DUAL(ROMD14, ROM16, ROM16S);
+SIG_EXPR_LIST_DECL_SINGLE(TXD6, TXD6, UART6_DESC);
+MS_PIN_DECL(A6, GPIOH6, ROMD14, TXD6);
+
+#define E7 63
+SIG_EXPR_DECL(ROMD15, ROM16, ROM16_DESC);
+SIG_EXPR_DECL(ROMD15, ROM16S, FLASH_WIDE, BOOT_SRC_NOR);
+SIG_EXPR_LIST_DECL_DUAL(ROMD15, ROM16, ROM16S);
+SIG_EXPR_LIST_DECL_SINGLE(RXD6, RXD6, UART6_DESC);
+MS_PIN_DECL(E7, GPIOH7, ROMD15, RXD6);
+
+FUNC_GROUP_DECL(UART6, A8, C7, B7, A7, D7, B6, A6, E7);
+
+#define J3 75
+SSSF_PIN_DECL(J3, GPIOJ3, SGPMI, SIG_DESC_SET(SCU84, 11));
+
+#define T4 76
+SSSF_PIN_DECL(T4, GPIOJ4, VGAHS, SIG_DESC_SET(SCU84, 12));
+
+#define U2 77
+SSSF_PIN_DECL(U2, GPIOJ5, VGAVS, SIG_DESC_SET(SCU84, 13));
+
+#define T2 78
+SSSF_PIN_DECL(T2, GPIOJ6, DDCCLK, SIG_DESC_SET(SCU84, 14));
+
+#define T1 79
+SSSF_PIN_DECL(T1, GPIOJ7, DDCDAT, SIG_DESC_SET(SCU84, 15));
+
+#define I2C5_DESC SIG_DESC_SET(SCU90, 18)
+
+#define E3 80
+SIG_EXPR_LIST_DECL_SINGLE(SCL5, I2C5, I2C5_DESC);
+SS_PIN_DECL(E3, GPIOK0, SCL5);
+
+#define D2 81
+SIG_EXPR_LIST_DECL_SINGLE(SDA5, I2C5, I2C5_DESC);
+SS_PIN_DECL(D2, GPIOK1, SDA5);
+
+FUNC_GROUP_DECL(I2C5, E3, D2);
+
+#define I2C6_DESC SIG_DESC_SET(SCU90, 19)
+
+#define C1 82
+SIG_EXPR_LIST_DECL_SINGLE(SCL6, I2C6, I2C6_DESC);
+SS_PIN_DECL(C1, GPIOK2, SCL6);
+
+#define F4 83
+SIG_EXPR_LIST_DECL_SINGLE(SDA6, I2C6, I2C6_DESC);
+SS_PIN_DECL(F4, GPIOK3, SDA6);
+
+FUNC_GROUP_DECL(I2C6, C1, F4);
+
+#define I2C7_DESC SIG_DESC_SET(SCU90, 20)
+
+#define E2 84
+SIG_EXPR_LIST_DECL_SINGLE(SCL7, I2C7, I2C7_DESC);
+SS_PIN_DECL(E2, GPIOK4, SCL7);
+
+#define D1 85
+SIG_EXPR_LIST_DECL_SINGLE(SDA7, I2C7, I2C7_DESC);
+SS_PIN_DECL(D1, GPIOK5, SDA7);
+
+FUNC_GROUP_DECL(I2C7, E2, D1);
+
+#define I2C8_DESC SIG_DESC_SET(SCU90, 21)
+
+#define G5 86
+SIG_EXPR_LIST_DECL_SINGLE(SCL8, I2C8, I2C8_DESC);
+SS_PIN_DECL(G5, GPIOK6, SCL8);
+
+#define F3 87
+SIG_EXPR_LIST_DECL_SINGLE(SDA8, I2C8, I2C8_DESC);
+SS_PIN_DECL(F3, GPIOK7, SDA8);
+
+FUNC_GROUP_DECL(I2C8, G5, F3);
+
+#define U1 88
+SSSF_PIN_DECL(U1, GPIOL0, NCTS1, SIG_DESC_SET(SCU84, 16));
+
+#define VPI18_DESC { SCU90, GENMASK(5, 4), 1, 0 }
+#define VPI24_DESC { SCU90, GENMASK(5, 4), 2, 0 }
+#define VPI30_DESC { SCU90, GENMASK(5, 4), 3, 0 }
+
+#define T5 89
+#define T5_DESC SIG_DESC_SET(SCU84, 17)
+SIG_EXPR_DECL(VPIDE, VPI18, VPI18_DESC, T5_DESC);
+SIG_EXPR_DECL(VPIDE, VPI24, VPI24_DESC, T5_DESC);
+SIG_EXPR_DECL(VPIDE, VPI30, VPI30_DESC, T5_DESC);
+SIG_EXPR_LIST_DECL(VPIDE, SIG_EXPR_PTR(VPIDE, VPI18),
+ SIG_EXPR_PTR(VPIDE, VPI24),
+ SIG_EXPR_PTR(VPIDE, VPI30));
+SIG_EXPR_LIST_DECL_SINGLE(NDCD1, NDCD1, T5_DESC);
+MS_PIN_DECL(T5, GPIOL1, VPIDE, NDCD1);
+FUNC_GROUP_DECL(NDCD1, T5);
+
+#define U3 90
+#define U3_DESC SIG_DESC_SET(SCU84, 18)
+SIG_EXPR_DECL(VPIODD, VPI18, VPI18_DESC, U3_DESC);
+SIG_EXPR_DECL(VPIODD, VPI24, VPI24_DESC, U3_DESC);
+SIG_EXPR_DECL(VPIODD, VPI30, VPI30_DESC, U3_DESC);
+SIG_EXPR_LIST_DECL(VPIODD, SIG_EXPR_PTR(VPIODD, VPI18),
+ SIG_EXPR_PTR(VPIODD, VPI24),
+ SIG_EXPR_PTR(VPIODD, VPI30));
+SIG_EXPR_LIST_DECL_SINGLE(NDSR1, NDSR1, U3_DESC);
+MS_PIN_DECL(U3, GPIOL2, VPIODD, NDSR1);
+FUNC_GROUP_DECL(NDSR1, U3);
+
+#define V1 91
+#define V1_DESC SIG_DESC_SET(SCU84, 19)
+SIG_EXPR_DECL(VPIHS, VPI18, VPI18_DESC, V1_DESC);
+SIG_EXPR_DECL(VPIHS, VPI24, VPI24_DESC, V1_DESC);
+SIG_EXPR_DECL(VPIHS, VPI30, VPI30_DESC, V1_DESC);
+SIG_EXPR_LIST_DECL(VPIHS, SIG_EXPR_PTR(VPIHS, VPI18),
+ SIG_EXPR_PTR(VPIHS, VPI24),
+ SIG_EXPR_PTR(VPIHS, VPI30));
+SIG_EXPR_LIST_DECL_SINGLE(NRI1, NRI1, V1_DESC);
+MS_PIN_DECL(V1, GPIOL3, VPIHS, NRI1);
+FUNC_GROUP_DECL(NRI1, V1);
+
+#define U4 92
+#define U4_DESC SIG_DESC_SET(SCU84, 20)
+SIG_EXPR_DECL(VPIVS, VPI18, VPI18_DESC, U4_DESC);
+SIG_EXPR_DECL(VPIVS, VPI24, VPI24_DESC, U4_DESC);
+SIG_EXPR_DECL(VPIVS, VPI30, VPI30_DESC, U4_DESC);
+SIG_EXPR_LIST_DECL(VPIVS, SIG_EXPR_PTR(VPIVS, VPI18),
+ SIG_EXPR_PTR(VPIVS, VPI24),
+ SIG_EXPR_PTR(VPIVS, VPI30));
+SIG_EXPR_LIST_DECL_SINGLE(NDTR1, NDTR1, U4_DESC);
+MS_PIN_DECL(U4, GPIOL4, VPIVS, NDTR1);
+FUNC_GROUP_DECL(NDTR1, U4);
+
+#define V2 93
+#define V2_DESC SIG_DESC_SET(SCU84, 21)
+SIG_EXPR_DECL(VPICLK, VPI18, VPI18_DESC, V2_DESC);
+SIG_EXPR_DECL(VPICLK, VPI24, VPI24_DESC, V2_DESC);
+SIG_EXPR_DECL(VPICLK, VPI30, VPI30_DESC, V2_DESC);
+SIG_EXPR_LIST_DECL(VPICLK, SIG_EXPR_PTR(VPICLK, VPI18),
+ SIG_EXPR_PTR(VPICLK, VPI24),
+ SIG_EXPR_PTR(VPICLK, VPI30));
+SIG_EXPR_LIST_DECL_SINGLE(NRTS1, NRTS1, V2_DESC);
+MS_PIN_DECL(V2, GPIOL5, VPICLK, NRTS1);
+FUNC_GROUP_DECL(NRTS1, V2);
+
+#define W1 94
+#define W1_DESC SIG_DESC_SET(SCU84, 22)
+SIG_EXPR_LIST_DECL_SINGLE(VPIB0, VPI30, VPI30_DESC, W1_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(TXD1, TXD1, W1_DESC);
+MS_PIN_DECL(W1, GPIOL6, VPIB0, TXD1);
+FUNC_GROUP_DECL(TXD1, W1);
+
+#define U5 95
+#define U5_DESC SIG_DESC_SET(SCU84, 23)
+SIG_EXPR_LIST_DECL_SINGLE(VPIB1, VPI30, VPI30_DESC, U5_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(RXD1, RXD1, U5_DESC);
+MS_PIN_DECL(U5, GPIOL7, VPIB1, RXD1);
+FUNC_GROUP_DECL(RXD1, U5);
+
+#define W4 104
+#define W4_DESC SIG_DESC_SET(SCU88, 0)
+SIG_EXPR_LIST_DECL_SINGLE(VPIG0, VPI30, VPI30_DESC, W4_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(PWM0, PWM0, W4_DESC);
+MS_PIN_DECL(W4, GPION0, VPIG0, PWM0);
+FUNC_GROUP_DECL(PWM0, W4);
+
+#define Y3 105
+#define Y3_DESC SIG_DESC_SET(SCU88, 1)
+SIG_EXPR_LIST_DECL_SINGLE(VPIG1, VPI30, VPI30_DESC, Y3_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(PWM1, PWM1, Y3_DESC);
+MS_PIN_DECL(Y3, GPION1, VPIG1, PWM1);
+FUNC_GROUP_DECL(PWM1, Y3);
+
+#define AA2 106
+#define AA2_DESC SIG_DESC_SET(SCU88, 2)
+SIG_EXPR_DECL(VPIG2, VPI18, VPI18_DESC, AA2_DESC);
+SIG_EXPR_DECL(VPIG2, VPI24, VPI24_DESC, AA2_DESC);
+SIG_EXPR_DECL(VPIG2, VPI30, VPI30_DESC, AA2_DESC);
+SIG_EXPR_LIST_DECL(VPIG2, SIG_EXPR_PTR(VPIG2, VPI18),
+ SIG_EXPR_PTR(VPIG2, VPI24),
+ SIG_EXPR_PTR(VPIG2, VPI30));
+SIG_EXPR_LIST_DECL_SINGLE(PWM2, PWM2, AA2_DESC);
+MS_PIN_DECL(AA2, GPION2, VPIG2, PWM2);
+FUNC_GROUP_DECL(PWM2, AA2);
+
+#define AB1 107
+#define AB1_DESC SIG_DESC_SET(SCU88, 3)
+SIG_EXPR_DECL(VPIG3, VPI18, VPI18_DESC, AB1_DESC);
+SIG_EXPR_DECL(VPIG3, VPI24, VPI24_DESC, AB1_DESC);
+SIG_EXPR_DECL(VPIG3, VPI30, VPI30_DESC, AB1_DESC);
+SIG_EXPR_LIST_DECL(VPIG3, SIG_EXPR_PTR(VPIG3, VPI18),
+ SIG_EXPR_PTR(VPIG2, VPI24),
+ SIG_EXPR_PTR(VPIG2, VPI30));
+SIG_EXPR_LIST_DECL_SINGLE(PWM3, PWM3, AB1_DESC);
+MS_PIN_DECL(AB1, GPION3, VPIG3, PWM3);
+FUNC_GROUP_DECL(PWM3, AB1);
+
+#define W5 108
+#define W5_DESC SIG_DESC_SET(SCU88, 4)
+SIG_EXPR_DECL(VPIG4, VPI18, VPI18_DESC, W5_DESC);
+SIG_EXPR_DECL(VPIG4, VPI24, VPI24_DESC, W5_DESC);
+SIG_EXPR_DECL(VPIG4, VPI30, VPI30_DESC, W5_DESC);
+SIG_EXPR_LIST_DECL(VPIG4, SIG_EXPR_PTR(VPIG4, VPI18),
+ SIG_EXPR_PTR(VPIG2, VPI24),
+ SIG_EXPR_PTR(VPIG2, VPI30));
+SIG_EXPR_LIST_DECL_SINGLE(PWM4, PWM4, W5_DESC);
+MS_PIN_DECL(W5, GPION4, VPIG4, PWM4);
+FUNC_GROUP_DECL(PWM4, W5);
+
+#define Y4 109
+#define Y4_DESC SIG_DESC_SET(SCU88, 5)
+SIG_EXPR_DECL(VPIG5, VPI18, VPI18_DESC, Y4_DESC);
+SIG_EXPR_DECL(VPIG5, VPI24, VPI24_DESC, Y4_DESC);
+SIG_EXPR_DECL(VPIG5, VPI30, VPI30_DESC, Y4_DESC);
+SIG_EXPR_LIST_DECL(VPIG5, SIG_EXPR_PTR(VPIG5, VPI18),
+ SIG_EXPR_PTR(VPIG2, VPI24),
+ SIG_EXPR_PTR(VPIG2, VPI30));
+SIG_EXPR_LIST_DECL_SINGLE(PWM5, PWM5, Y4_DESC);
+MS_PIN_DECL(Y4, GPION5, VPIG5, PWM5);
+FUNC_GROUP_DECL(PWM5, Y4);
+
+#define AA3 110
+#define AA3_DESC SIG_DESC_SET(SCU88, 6)
+SIG_EXPR_LIST_DECL_SINGLE(VPIG6, VPI30, VPI30_DESC, AA3_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(PWM6, PWM6, AA3_DESC);
+MS_PIN_DECL(AA3, GPION6, VPIG6, PWM6);
+FUNC_GROUP_DECL(PWM6, AA3);
+
+#define AB2 111
+#define AB2_DESC SIG_DESC_SET(SCU88, 7)
+SIG_EXPR_LIST_DECL_SINGLE(VPIG7, VPI30, VPI30_DESC, AB2_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(PWM7, PWM7, AB2_DESC);
+MS_PIN_DECL(AB2, GPION7, VPIG7, PWM7);
+FUNC_GROUP_DECL(PWM7, AB2);
+
+#define V6 112
+SIG_EXPR_LIST_DECL_SINGLE(VPIG8, VPI24, VPI24_DESC, SIG_DESC_SET(SCU88, 8));
+SS_PIN_DECL(V6, GPIOO0, VPIG8);
+
+#define Y5 113
+SIG_EXPR_LIST_DECL_SINGLE(VPIG9, VPI24, VPI24_DESC, SIG_DESC_SET(SCU88, 9));
+SS_PIN_DECL(Y5, GPIOO1, VPIG9);
+
+FUNC_GROUP_DECL(VPI18, T5, U3, V1, U4, V2, AA22, W5, Y4, AA3, AB2);
+FUNC_GROUP_DECL(VPI24, T5, U3, V1, U4, V2, AA22, W5, Y4, AA3, AB2, V6, Y5);
+FUNC_GROUP_DECL(VPI30, T5, U3, V1, U4, V2, W1, U5, W4, Y3, AA22, W5, Y4, AA3,
+ AB2);
+
+#define Y7 125
+SIG_EXPR_LIST_DECL_SINGLE(GPIOP5, GPIOP5);
+MS_PIN_DECL_(Y7, SIG_EXPR_LIST_PTR(GPIOP5));
+
+#define AA7 126
+SSSF_PIN_DECL(AA7, GPIOP6, BMCINT, SIG_DESC_SET(SCU88, 22));
+
+#define AB7 127
+SSSF_PIN_DECL(AB7, GPIOP7, FLACK, SIG_DESC_SET(SCU88, 23));
+
+#define I2C3_DESC SIG_DESC_SET(SCU90, 16)
+
+#define D3 128
+SIG_EXPR_LIST_DECL_SINGLE(SCL3, I2C3, I2C3_DESC);
+SS_PIN_DECL(D3, GPIOQ0, SCL3);
+
+#define C2 129
+SIG_EXPR_LIST_DECL_SINGLE(SDA3, I2C3, I2C3_DESC);
+SS_PIN_DECL(C2, GPIOQ1, SDA3);
+
+FUNC_GROUP_DECL(I2C3, D3, C2);
+
+#define I2C4_DESC SIG_DESC_SET(SCU90, 17)
+
+#define B1 130
+SIG_EXPR_LIST_DECL_SINGLE(SCL4, I2C4, I2C4_DESC);
+SS_PIN_DECL(B1, GPIOQ2, SCL4);
+
+#define F5 131
+SIG_EXPR_LIST_DECL_SINGLE(SDA4, I2C4, I2C4_DESC);
+SS_PIN_DECL(F5, GPIOQ3, SDA4);
+
+FUNC_GROUP_DECL(I2C4, B1, F5);
+
+#define DASH9028_DESC SIG_DESC_SET(SCU90, 28)
+
+#define H2 134
+SSSF_PIN_DECL(H2, GPIOQ6, DASHH2, DASH9028_DESC);
+
+#define H1 135
+SSSF_PIN_DECL(H1, GPIOQ7, DASHH1, DASH9028_DESC);
+
+#define VPOOFF0_DESC { SCU94, GENMASK(1, 0), 0, 0 }
+#define VPO12_DESC { SCU94, GENMASK(1, 0), 1, 0 }
+#define VPO24_DESC { SCU94, GENMASK(1, 0), 2, 0 }
+#define VPOOFF1_DESC { SCU94, GENMASK(1, 0), 3, 0 }
+#define VPO_OFF_12 { SCU94, 0x2, 0, 0 }
+#define VPO_24_OFF SIG_DESC_SET(SCU94, 1)
+
+#define V20 136
+#define V20_DESC SIG_DESC_SET(SCU88, 24)
+SIG_EXPR_LIST_DECL_SINGLE(GPIOR0, GPIOR0);
+SIG_EXPR_DECL(ROMCS1, ROM8, V20_DESC);
+SIG_EXPR_DECL(ROMCS1, ROM16, V20_DESC);
+SIG_EXPR_DECL(ROMCS1, ROM16S, V20_DESC);
+SIG_EXPR_LIST_DECL(ROMCS1, SIG_EXPR_PTR(ROMCS1, ROM8),
+ SIG_EXPR_PTR(ROMCS1, ROM16),
+ SIG_EXPR_PTR(ROMCS1, ROM16S));
+MS_PIN_DECL_(V20, SIG_EXPR_LIST_PTR(ROMCS1), SIG_EXPR_LIST_PTR(GPIOR0));
+
+#define U21 144
+#define U21_DESC SIG_DESC_SET(SCU8C, 0)
+SIG_EXPR_DECL(ROMD4, ROM8, U21_DESC, VPOOFF0_DESC);
+SIG_EXPR_DECL(ROMD4, ROM16, U21_DESC, VPOOFF0_DESC);
+SIG_EXPR_DECL(ROMD4, ROM16S, U21_DESC, VPOOFF0_DESC);
+SIG_EXPR_LIST_DECL(ROMD4, SIG_EXPR_PTR(ROMD4, ROM8),
+ SIG_EXPR_PTR(ROMD4, ROM16),
+ SIG_EXPR_PTR(ROMD4, ROM16S));
+SIG_EXPR_DECL(VPODE, VPO12, U21_DESC, VPO12_DESC);
+SIG_EXPR_DECL(VPODE, VPO24, U21_DESC, VPO12_DESC);
+SIG_EXPR_LIST_DECL_DUAL(VPODE, VPO12, VPO24);
+MS_PIN_DECL(U21, GPIOS0, ROMD4, VPODE);
+
+#define T19 145
+#define T19_DESC SIG_DESC_SET(SCU8C, 1)
+SIG_EXPR_DECL(ROMD5, ROM8, T19_DESC, VPOOFF0_DESC);
+SIG_EXPR_DECL(ROMD5, ROM16, T19_DESC, VPOOFF0_DESC);
+SIG_EXPR_DECL(ROMD5, ROM16S, T19_DESC, VPOOFF0_DESC);
+SIG_EXPR_LIST_DECL(ROMD5, SIG_EXPR_PTR(ROMD5, ROM8),
+ SIG_EXPR_PTR(ROMD5, ROM16),
+ SIG_EXPR_PTR(ROMD5, ROM16S));
+SIG_EXPR_DECL(VPOHS, VPO12, T19_DESC, VPO12_DESC);
+SIG_EXPR_DECL(VPOHS, VPO24, T19_DESC, VPO24_DESC);
+SIG_EXPR_LIST_DECL_DUAL(VPOHS, VPO12, VPO24);
+MS_PIN_DECL(T19, GPIOS1, ROMD5, VPOHS);
+
+#define V22 146
+#define V22_DESC SIG_DESC_SET(SCU8C, 2)
+SIG_EXPR_DECL(ROMD6, ROM8, V22_DESC, VPOOFF0_DESC);
+SIG_EXPR_DECL(ROMD6, ROM16, V22_DESC, VPOOFF0_DESC);
+SIG_EXPR_DECL(ROMD6, ROM16S, V22_DESC, VPOOFF0_DESC);
+SIG_EXPR_LIST_DECL(ROMD6, SIG_EXPR_PTR(ROMD6, ROM8),
+ SIG_EXPR_PTR(ROMD6, ROM16),
+ SIG_EXPR_PTR(ROMD6, ROM16S));
+SIG_EXPR_DECL(VPOVS, VPO12, V22_DESC, VPO12_DESC);
+SIG_EXPR_DECL(VPOVS, VPO24, V22_DESC, VPO24_DESC);
+SIG_EXPR_LIST_DECL_DUAL(VPOVS, VPO12, VPO24);
+MS_PIN_DECL(V22, GPIOS2, ROMD6, VPOVS);
+
+#define U20 147
+#define U20_DESC SIG_DESC_SET(SCU8C, 3)
+SIG_EXPR_DECL(ROMD7, ROM8, U20_DESC, VPOOFF0_DESC);
+SIG_EXPR_DECL(ROMD7, ROM16, U20_DESC, VPOOFF0_DESC);
+SIG_EXPR_DECL(ROMD7, ROM16S, U20_DESC, VPOOFF0_DESC);
+SIG_EXPR_LIST_DECL(ROMD7, SIG_EXPR_PTR(ROMD7, ROM8),
+ SIG_EXPR_PTR(ROMD7, ROM16),
+ SIG_EXPR_PTR(ROMD7, ROM16S));
+SIG_EXPR_DECL(VPOCLK, VPO12, U20_DESC, VPO12_DESC);
+SIG_EXPR_DECL(VPOCLK, VPO24, U20_DESC, VPO24_DESC);
+SIG_EXPR_LIST_DECL_DUAL(VPOCLK, VPO12, VPO24);
+MS_PIN_DECL(U20, GPIOS3, ROMD7, VPOCLK);
+
+#define R18 148
+#define ROMOE_DESC SIG_DESC_SET(SCU8C, 4)
+SIG_EXPR_LIST_DECL_SINGLE(GPIOS4, GPIOS4);
+SIG_EXPR_DECL(ROMOE, ROM8, ROMOE_DESC);
+SIG_EXPR_DECL(ROMOE, ROM16, ROMOE_DESC);
+SIG_EXPR_DECL(ROMOE, ROM16S, ROMOE_DESC);
+SIG_EXPR_LIST_DECL(ROMOE, SIG_EXPR_PTR(ROMOE, ROM8),
+ SIG_EXPR_PTR(ROMOE, ROM16),
+ SIG_EXPR_PTR(ROMOE, ROM16S));
+MS_PIN_DECL_(R18, SIG_EXPR_LIST_PTR(ROMOE), SIG_EXPR_LIST_PTR(GPIOS4));
+
+#define N21 149
+#define ROMWE_DESC SIG_DESC_SET(SCU8C, 5)
+SIG_EXPR_LIST_DECL_SINGLE(GPIOS5, GPIOS5);
+SIG_EXPR_DECL(ROMWE, ROM8, ROMWE_DESC);
+SIG_EXPR_DECL(ROMWE, ROM16, ROMWE_DESC);
+SIG_EXPR_DECL(ROMWE, ROM16S, ROMWE_DESC);
+SIG_EXPR_LIST_DECL(ROMWE, SIG_EXPR_PTR(ROMWE, ROM8),
+ SIG_EXPR_PTR(ROMWE, ROM16),
+ SIG_EXPR_PTR(ROMWE, ROM16S));
+MS_PIN_DECL_(N21, SIG_EXPR_LIST_PTR(ROMWE), SIG_EXPR_LIST_PTR(GPIOS5));
+
+#define L22 150
+#define L22_DESC SIG_DESC_SET(SCU8C, 6)
+SIG_EXPR_DECL(ROMA22, ROM8, L22_DESC, VPO_OFF_12);
+SIG_EXPR_DECL(ROMA22, ROM16, L22_DESC, VPO_OFF_12);
+SIG_EXPR_DECL(ROMA22, ROM16S, L22_DESC, VPO_OFF_12);
+SIG_EXPR_LIST_DECL(ROMA22, SIG_EXPR_PTR(ROMA22, ROM8),
+ SIG_EXPR_PTR(ROMA22, ROM16),
+ SIG_EXPR_PTR(ROMA22, ROM16S));
+SIG_EXPR_LIST_DECL_SINGLE(VPOR4, VPO24, L22_DESC, VPO_24_OFF);
+MS_PIN_DECL(L22, GPIOS6, ROMA22, VPOR4);
+
+#define K18 151
+#define K18_DESC SIG_DESC_SET(SCU8C, 7)
+SIG_EXPR_DECL(ROMA23, ROM8, K18_DESC, VPO_OFF_12);
+SIG_EXPR_DECL(ROMA23, ROM16, K18_DESC, VPO_OFF_12);
+SIG_EXPR_DECL(ROMA23, ROM16S, K18_DESC, VPO_OFF_12);
+SIG_EXPR_LIST_DECL(ROMA23, SIG_EXPR_PTR(ROMA23, ROM8),
+ SIG_EXPR_PTR(ROMA23, ROM16),
+ SIG_EXPR_PTR(ROMA23, ROM16S));
+SIG_EXPR_LIST_DECL_SINGLE(VPOR5, VPO24, K18_DESC, VPO_24_OFF);
+MS_PIN_DECL(K18, GPIOS7, ROMA23, VPOR5);
+
+FUNC_GROUP_DECL(ROM8, V20, U21, T19, V22, U20, R18, N21, L22, K18);
+FUNC_GROUP_DECL(ROM16, V20, U21, T19, V22, U20, R18, N21, L22, K18,
+ A8, C7, B7, A7, D7, B6, A6, E7);
+FUNC_GROUP_DECL(VPO12, U21, T19, V22, U20);
+FUNC_GROUP_DECL(VPO24, U21, T19, V22, U20, L22, K18);
+
+#define RMII1_DESC { HW_STRAP1, BIT(6), 0, 0 }
+
+#define A12 152
+SIG_EXPR_LIST_DECL_SINGLE(GPIOT0, GPIOT0, SIG_DESC_SET(SCUA0, 0));
+SIG_EXPR_LIST_DECL_SINGLE(RMII1TXEN, RMII1, RMII1_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(RGMII1TXCK, RGMII1);
+MS_PIN_DECL_(A12, SIG_EXPR_LIST_PTR(GPIOT0), SIG_EXPR_LIST_PTR(RMII1TXEN),
+ SIG_EXPR_LIST_PTR(RGMII1TXCK));
+
+#define B12 153
+SIG_EXPR_LIST_DECL_SINGLE(GPIOT1, GPIOT1, SIG_DESC_SET(SCUA0, 1));
+SIG_EXPR_LIST_DECL_SINGLE(DASHB12, RMII1, RMII1_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(RGMII1TXCTL, RGMII1);
+MS_PIN_DECL_(B12, SIG_EXPR_LIST_PTR(GPIOT1), SIG_EXPR_LIST_PTR(DASHB12),
+ SIG_EXPR_LIST_PTR(RGMII1TXCTL));
+
+#define C12 154
+SIG_EXPR_LIST_DECL_SINGLE(GPIOT2, GPIOT2, SIG_DESC_SET(SCUA0, 2));
+SIG_EXPR_LIST_DECL_SINGLE(RMII1TXD0, RMII1, RMII1_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(RGMII1TXD0, RGMII1);
+MS_PIN_DECL_(C12, SIG_EXPR_LIST_PTR(GPIOT2), SIG_EXPR_LIST_PTR(RMII1TXD0),
+ SIG_EXPR_LIST_PTR(RGMII1TXD0));
+
+#define D12 155
+SIG_EXPR_LIST_DECL_SINGLE(GPIOT3, GPIOT3, SIG_DESC_SET(SCUA0, 3));
+SIG_EXPR_LIST_DECL_SINGLE(RMII1TXD1, RMII1, RMII1_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(RGMII1TXD1, RGMII1);
+MS_PIN_DECL_(D12, SIG_EXPR_LIST_PTR(GPIOT3), SIG_EXPR_LIST_PTR(RMII1TXD1),
+ SIG_EXPR_LIST_PTR(RGMII1TXD1));
+
+#define E12 156
+SIG_EXPR_LIST_DECL_SINGLE(GPIOT4, GPIOT4, SIG_DESC_SET(SCUA0, 4));
+SIG_EXPR_LIST_DECL_SINGLE(DASHE12, RMII1, RMII1_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(RGMII1TXD2, RGMII1);
+MS_PIN_DECL_(E12, SIG_EXPR_LIST_PTR(GPIOT4), SIG_EXPR_LIST_PTR(DASHE12),
+ SIG_EXPR_LIST_PTR(RGMII1TXD2));
+
+#define A13 157
+SIG_EXPR_LIST_DECL_SINGLE(GPIOT5, GPIOT5, SIG_DESC_SET(SCUA0, 5));
+SIG_EXPR_LIST_DECL_SINGLE(DASHA13, RMII1, RMII1_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(RGMII1TXD3, RGMII1);
+MS_PIN_DECL_(A13, SIG_EXPR_LIST_PTR(GPIOT5), SIG_EXPR_LIST_PTR(DASHA13),
+ SIG_EXPR_LIST_PTR(RGMII1TXD3));
+
+#define E11 164
+SIG_EXPR_LIST_DECL_SINGLE(GPIOU4, GPIOU4, SIG_DESC_SET(SCUA0, 12));
+SIG_EXPR_LIST_DECL_SINGLE(RMII1RCLK, RMII1, RMII1_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(RGMII1RXCK, RGMII1);
+MS_PIN_DECL_(E11, SIG_EXPR_LIST_PTR(GPIOU4), SIG_EXPR_LIST_PTR(RMII1RCLK),
+ SIG_EXPR_LIST_PTR(RGMII1RXCK));
+
+#define D11 165
+SIG_EXPR_LIST_DECL_SINGLE(GPIOU5, GPIOU5, SIG_DESC_SET(SCUA0, 13));
+SIG_EXPR_LIST_DECL_SINGLE(DASHD11, RMII1, RMII1_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(RGMII1RXCTL, RGMII1);
+MS_PIN_DECL_(D11, SIG_EXPR_LIST_PTR(GPIOU5), SIG_EXPR_LIST_PTR(DASHD11),
+ SIG_EXPR_LIST_PTR(RGMII1RXCTL));
+
+#define C11 166
+SIG_EXPR_LIST_DECL_SINGLE(GPIOU6, GPIOU6, SIG_DESC_SET(SCUA0, 14));
+SIG_EXPR_LIST_DECL_SINGLE(RMII1RXD0, RMII1, RMII1_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(RGMII1RXD0, RGMII1);
+MS_PIN_DECL_(C11, SIG_EXPR_LIST_PTR(GPIOU6), SIG_EXPR_LIST_PTR(RMII1RXD0),
+ SIG_EXPR_LIST_PTR(RGMII1RXD0));
+
+#define B11 167
+SIG_EXPR_LIST_DECL_SINGLE(GPIOU7, GPIOU7, SIG_DESC_SET(SCUA0, 15));
+SIG_EXPR_LIST_DECL_SINGLE(RMII1RXD1, RMII1, RMII1_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(RGMII1RXD1, RGMII1);
+MS_PIN_DECL_(B11, SIG_EXPR_LIST_PTR(GPIOU7), SIG_EXPR_LIST_PTR(RMII1RXD1),
+ SIG_EXPR_LIST_PTR(RGMII1RXD1));
+
+#define A11 168
+SIG_EXPR_LIST_DECL_SINGLE(GPIOV0, GPIOV0, SIG_DESC_SET(SCUA0, 16));
+SIG_EXPR_LIST_DECL_SINGLE(RMII1CRSDV, RMII1, RMII1_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(RGMII1RXD2, RGMII1);
+MS_PIN_DECL_(A11, SIG_EXPR_LIST_PTR(GPIOV0), SIG_EXPR_LIST_PTR(RMII1CRSDV),
+ SIG_EXPR_LIST_PTR(RGMII1RXD2));
+
+#define E10 169
+SIG_EXPR_LIST_DECL_SINGLE(GPIOV1, GPIOV1, SIG_DESC_SET(SCUA0, 17));
+SIG_EXPR_LIST_DECL_SINGLE(RMII1RXER, RMII1, RMII1_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(RGMII1RXD3, RGMII1);
+MS_PIN_DECL_(E10, SIG_EXPR_LIST_PTR(GPIOV1), SIG_EXPR_LIST_PTR(RMII1RXER),
+ SIG_EXPR_LIST_PTR(RGMII1RXD3));
+
+FUNC_GROUP_DECL(RMII1, A12, B12, C12, D12, E12, A13, E11, D11, C11, B11, A11,
+ E10);
+FUNC_GROUP_DECL(RGMII1, A12, B12, C12, D12, E12, A13, E11, D11, C11, B11, A11,
+ E10);
+
+/* Note we account for GPIOY4-GPIOY7 even though they're not valid, thus 216
+ * pins becomes 220.
+ */
+#define ASPEED_G4_NR_PINS 220
+
+static struct pinctrl_pin_desc aspeed_g4_pins[ASPEED_G4_NR_PINS] = {
+ ASPEED_PINCTRL_PIN(A4),
+ ASPEED_PINCTRL_PIN(C5),
+ ASPEED_PINCTRL_PIN(B4),
+ ASPEED_PINCTRL_PIN(A3),
+ ASPEED_PINCTRL_PIN(D5),
+ ASPEED_PINCTRL_PIN(H19),
+ ASPEED_PINCTRL_PIN(H20),
+ ASPEED_PINCTRL_PIN(C4),
+ ASPEED_PINCTRL_PIN(B3),
+ ASPEED_PINCTRL_PIN(A2),
+ ASPEED_PINCTRL_PIN(E5),
+ ASPEED_PINCTRL_PIN(D4),
+ ASPEED_PINCTRL_PIN(C3),
+ ASPEED_PINCTRL_PIN(B2),
+ ASPEED_PINCTRL_PIN(A1),
+ ASPEED_PINCTRL_PIN(A18),
+ ASPEED_PINCTRL_PIN(D16),
+ ASPEED_PINCTRL_PIN(D15),
+ ASPEED_PINCTRL_PIN(C15),
+ ASPEED_PINCTRL_PIN(D18),
+ ASPEED_PINCTRL_PIN(B19),
+ ASPEED_PINCTRL_PIN(D17),
+ ASPEED_PINCTRL_PIN(E16),
+ ASPEED_PINCTRL_PIN(C17),
+ ASPEED_PINCTRL_PIN(AA22),
+ ASPEED_PINCTRL_PIN(U18),
+ ASPEED_PINCTRL_PIN(A8),
+ ASPEED_PINCTRL_PIN(C7),
+ ASPEED_PINCTRL_PIN(B7),
+ ASPEED_PINCTRL_PIN(A7),
+ ASPEED_PINCTRL_PIN(D7),
+ ASPEED_PINCTRL_PIN(B6),
+ ASPEED_PINCTRL_PIN(A6),
+ ASPEED_PINCTRL_PIN(E7),
+ ASPEED_PINCTRL_PIN(J3),
+ ASPEED_PINCTRL_PIN(T4),
+ ASPEED_PINCTRL_PIN(U2),
+ ASPEED_PINCTRL_PIN(T2),
+ ASPEED_PINCTRL_PIN(T1),
+ ASPEED_PINCTRL_PIN(E3),
+ ASPEED_PINCTRL_PIN(D2),
+ ASPEED_PINCTRL_PIN(C1),
+ ASPEED_PINCTRL_PIN(F4),
+ ASPEED_PINCTRL_PIN(E2),
+ ASPEED_PINCTRL_PIN(D1),
+ ASPEED_PINCTRL_PIN(G5),
+ ASPEED_PINCTRL_PIN(F3),
+ ASPEED_PINCTRL_PIN(U1),
+ ASPEED_PINCTRL_PIN(T5),
+ ASPEED_PINCTRL_PIN(U3),
+ ASPEED_PINCTRL_PIN(V1),
+ ASPEED_PINCTRL_PIN(U4),
+ ASPEED_PINCTRL_PIN(V2),
+ ASPEED_PINCTRL_PIN(W1),
+ ASPEED_PINCTRL_PIN(U5),
+ ASPEED_PINCTRL_PIN(W4),
+ ASPEED_PINCTRL_PIN(Y3),
+ ASPEED_PINCTRL_PIN(AA2),
+ ASPEED_PINCTRL_PIN(AB1),
+ ASPEED_PINCTRL_PIN(W5),
+ ASPEED_PINCTRL_PIN(Y4),
+ ASPEED_PINCTRL_PIN(AA3),
+ ASPEED_PINCTRL_PIN(AB2),
+ ASPEED_PINCTRL_PIN(V6),
+ ASPEED_PINCTRL_PIN(Y5),
+ ASPEED_PINCTRL_PIN(Y7),
+ ASPEED_PINCTRL_PIN(AA7),
+ ASPEED_PINCTRL_PIN(AB7),
+ ASPEED_PINCTRL_PIN(D3),
+ ASPEED_PINCTRL_PIN(C2),
+ ASPEED_PINCTRL_PIN(B1),
+ ASPEED_PINCTRL_PIN(F5),
+ ASPEED_PINCTRL_PIN(H2),
+ ASPEED_PINCTRL_PIN(H1),
+ ASPEED_PINCTRL_PIN(V20),
+ ASPEED_PINCTRL_PIN(U21),
+ ASPEED_PINCTRL_PIN(T19),
+ ASPEED_PINCTRL_PIN(V22),
+ ASPEED_PINCTRL_PIN(U20),
+ ASPEED_PINCTRL_PIN(R18),
+ ASPEED_PINCTRL_PIN(N21),
+ ASPEED_PINCTRL_PIN(L22),
+ ASPEED_PINCTRL_PIN(K18),
+ ASPEED_PINCTRL_PIN(A12),
+ ASPEED_PINCTRL_PIN(B12),
+ ASPEED_PINCTRL_PIN(C12),
+ ASPEED_PINCTRL_PIN(D12),
+ ASPEED_PINCTRL_PIN(E12),
+ ASPEED_PINCTRL_PIN(A13),
+ ASPEED_PINCTRL_PIN(E11),
+ ASPEED_PINCTRL_PIN(D11),
+ ASPEED_PINCTRL_PIN(C11),
+ ASPEED_PINCTRL_PIN(B11),
+ ASPEED_PINCTRL_PIN(A11),
+ ASPEED_PINCTRL_PIN(E10),
+};
+
+static const struct aspeed_pin_group aspeed_g4_groups[] = {
+ ASPEED_PINCTRL_GROUP(TIMER3),
+ ASPEED_PINCTRL_GROUP(I2C9),
+ ASPEED_PINCTRL_GROUP(TIMER5),
+ ASPEED_PINCTRL_GROUP(TIMER6),
+ ASPEED_PINCTRL_GROUP(MDIO2),
+ ASPEED_PINCTRL_GROUP(LPCPD),
+ ASPEED_PINCTRL_GROUP(LPCSMI),
+ ASPEED_PINCTRL_GROUP(LPCPME),
+ ASPEED_PINCTRL_GROUP(TIMER7),
+ ASPEED_PINCTRL_GROUP(TIMER8),
+ ASPEED_PINCTRL_GROUP(SD1),
+ ASPEED_PINCTRL_GROUP(GPID0),
+ ASPEED_PINCTRL_GROUP(I2C10),
+ ASPEED_PINCTRL_GROUP(I2C11),
+ ASPEED_PINCTRL_GROUP(I2C12),
+ ASPEED_PINCTRL_GROUP(I2C13),
+ ASPEED_PINCTRL_GROUP(NCTS3),
+ ASPEED_PINCTRL_GROUP(NDCD3),
+ ASPEED_PINCTRL_GROUP(GPIE0),
+ ASPEED_PINCTRL_GROUP(NCTS4),
+ ASPEED_PINCTRL_GROUP(ACPI),
+ ASPEED_PINCTRL_GROUP(NDCD4),
+ ASPEED_PINCTRL_GROUP(SIOPBI),
+ ASPEED_PINCTRL_GROUP(NRI4),
+ ASPEED_PINCTRL_GROUP(SIOPBO),
+ ASPEED_PINCTRL_GROUP(TXD4),
+ ASPEED_PINCTRL_GROUP(RXD4),
+ ASPEED_PINCTRL_GROUP(FLBUSY),
+ ASPEED_PINCTRL_GROUP(FLWP),
+ ASPEED_PINCTRL_GROUP(UART6),
+ ASPEED_PINCTRL_GROUP(SGPMI),
+ ASPEED_PINCTRL_GROUP(VGAHS),
+ ASPEED_PINCTRL_GROUP(VGAVS),
+ ASPEED_PINCTRL_GROUP(DDCCLK),
+ ASPEED_PINCTRL_GROUP(DDCDAT),
+ ASPEED_PINCTRL_GROUP(I2C5),
+ ASPEED_PINCTRL_GROUP(I2C6),
+ ASPEED_PINCTRL_GROUP(I2C7),
+ ASPEED_PINCTRL_GROUP(I2C8),
+ ASPEED_PINCTRL_GROUP(NCTS1),
+ ASPEED_PINCTRL_GROUP(NDCD1),
+ ASPEED_PINCTRL_GROUP(NDSR1),
+ ASPEED_PINCTRL_GROUP(NRI1),
+ ASPEED_PINCTRL_GROUP(NDTR1),
+ ASPEED_PINCTRL_GROUP(NRTS1),
+ ASPEED_PINCTRL_GROUP(TXD1),
+ ASPEED_PINCTRL_GROUP(RXD1),
+ ASPEED_PINCTRL_GROUP(PWM0),
+ ASPEED_PINCTRL_GROUP(PWM1),
+ ASPEED_PINCTRL_GROUP(PWM2),
+ ASPEED_PINCTRL_GROUP(PWM3),
+ ASPEED_PINCTRL_GROUP(PWM4),
+ ASPEED_PINCTRL_GROUP(PWM5),
+ ASPEED_PINCTRL_GROUP(PWM6),
+ ASPEED_PINCTRL_GROUP(PWM7),
+ ASPEED_PINCTRL_GROUP(VPI18),
+ ASPEED_PINCTRL_GROUP(VPI24),
+ ASPEED_PINCTRL_GROUP(VPI30),
+ ASPEED_PINCTRL_GROUP(BMCINT),
+ ASPEED_PINCTRL_GROUP(FLACK),
+ ASPEED_PINCTRL_GROUP(I2C3),
+ ASPEED_PINCTRL_GROUP(I2C4),
+ ASPEED_PINCTRL_GROUP(DASHH2),
+ ASPEED_PINCTRL_GROUP(DASHH1),
+ ASPEED_PINCTRL_GROUP(ROM8),
+ ASPEED_PINCTRL_GROUP(ROM16),
+ ASPEED_PINCTRL_GROUP(VPO12),
+ ASPEED_PINCTRL_GROUP(VPO24),
+ ASPEED_PINCTRL_GROUP(RGMII1),
+ ASPEED_PINCTRL_GROUP(RMII1),
+};
+
+static const struct aspeed_pin_function aspeed_g4_functions[] = {
+ ASPEED_PINCTRL_FUNC(TIMER3),
+ ASPEED_PINCTRL_FUNC(I2C9),
+ ASPEED_PINCTRL_FUNC(TIMER5),
+ ASPEED_PINCTRL_FUNC(TIMER6),
+ ASPEED_PINCTRL_FUNC(MDIO2),
+ ASPEED_PINCTRL_FUNC(LPCPD),
+ ASPEED_PINCTRL_FUNC(LPCSMI),
+ ASPEED_PINCTRL_FUNC(TIMER7),
+ ASPEED_PINCTRL_FUNC(TIMER8),
+ ASPEED_PINCTRL_FUNC(SD1),
+ ASPEED_PINCTRL_FUNC(GPID0),
+ ASPEED_PINCTRL_FUNC(I2C10),
+ ASPEED_PINCTRL_FUNC(I2C11),
+ ASPEED_PINCTRL_FUNC(I2C12),
+ ASPEED_PINCTRL_FUNC(I2C13),
+ ASPEED_PINCTRL_FUNC(NCTS3),
+ ASPEED_PINCTRL_FUNC(NDCD3),
+ ASPEED_PINCTRL_FUNC(GPIE0),
+ ASPEED_PINCTRL_FUNC(NCTS4),
+ ASPEED_PINCTRL_FUNC(ACPI),
+ ASPEED_PINCTRL_FUNC(NDCD4),
+ ASPEED_PINCTRL_FUNC(SIOPBI),
+ ASPEED_PINCTRL_FUNC(NRI4),
+ ASPEED_PINCTRL_FUNC(SIOPBO),
+ ASPEED_PINCTRL_FUNC(TXD4),
+ ASPEED_PINCTRL_FUNC(RXD4),
+ ASPEED_PINCTRL_FUNC(FLBUSY),
+ ASPEED_PINCTRL_FUNC(FLWP),
+ ASPEED_PINCTRL_FUNC(UART6),
+ ASPEED_PINCTRL_FUNC(SGPMI),
+ ASPEED_PINCTRL_FUNC(VGAHS),
+ ASPEED_PINCTRL_FUNC(VGAVS),
+ ASPEED_PINCTRL_FUNC(DDCCLK),
+ ASPEED_PINCTRL_FUNC(DDCDAT),
+ ASPEED_PINCTRL_FUNC(I2C5),
+ ASPEED_PINCTRL_FUNC(I2C6),
+ ASPEED_PINCTRL_FUNC(I2C7),
+ ASPEED_PINCTRL_FUNC(I2C8),
+ ASPEED_PINCTRL_FUNC(NCTS1),
+ ASPEED_PINCTRL_FUNC(NDCD1),
+ ASPEED_PINCTRL_FUNC(NDSR1),
+ ASPEED_PINCTRL_FUNC(NRI1),
+ ASPEED_PINCTRL_FUNC(NDTR1),
+ ASPEED_PINCTRL_FUNC(NRTS1),
+ ASPEED_PINCTRL_FUNC(TXD1),
+ ASPEED_PINCTRL_FUNC(RXD1),
+ ASPEED_PINCTRL_FUNC(PWM0),
+ ASPEED_PINCTRL_FUNC(PWM1),
+ ASPEED_PINCTRL_FUNC(PWM2),
+ ASPEED_PINCTRL_FUNC(PWM3),
+ ASPEED_PINCTRL_FUNC(PWM4),
+ ASPEED_PINCTRL_FUNC(PWM5),
+ ASPEED_PINCTRL_FUNC(PWM6),
+ ASPEED_PINCTRL_FUNC(PWM7),
+ ASPEED_PINCTRL_FUNC(VPI18),
+ ASPEED_PINCTRL_FUNC(VPI24),
+ ASPEED_PINCTRL_FUNC(VPI30),
+ ASPEED_PINCTRL_FUNC(BMCINT),
+ ASPEED_PINCTRL_FUNC(FLACK),
+ ASPEED_PINCTRL_FUNC(I2C3),
+ ASPEED_PINCTRL_FUNC(I2C4),
+ ASPEED_PINCTRL_FUNC(ROM8),
+ ASPEED_PINCTRL_FUNC(ROM16),
+ ASPEED_PINCTRL_FUNC(VPO12),
+ ASPEED_PINCTRL_FUNC(VPO24),
+ ASPEED_PINCTRL_FUNC(RGMII1),
+ ASPEED_PINCTRL_FUNC(RMII1),
+};
+
+static struct aspeed_pinctrl_data aspeed_g4_pinctrl_data = {
+ .pins = aspeed_g4_pins,
+ .npins = ARRAY_SIZE(aspeed_g4_pins),
+ .groups = aspeed_g4_groups,
+ .ngroups = ARRAY_SIZE(aspeed_g4_groups),
+ .functions = aspeed_g4_functions,
+ .nfunctions = ARRAY_SIZE(aspeed_g4_functions),
+};
+
+static struct pinmux_ops aspeed_g4_pinmux_ops = {
+ .get_functions_count = aspeed_pinmux_get_fn_count,
+ .get_function_name = aspeed_pinmux_get_fn_name,
+ .get_function_groups = aspeed_pinmux_get_fn_groups,
+ .set_mux = aspeed_pinmux_set_mux,
+ .gpio_request_enable = aspeed_gpio_request_enable,
+ .strict = true,
+};
+
+static struct pinctrl_ops aspeed_g4_pinctrl_ops = {
+ .get_groups_count = aspeed_pinctrl_get_groups_count,
+ .get_group_name = aspeed_pinctrl_get_group_name,
+ .get_group_pins = aspeed_pinctrl_get_group_pins,
+ .pin_dbg_show = aspeed_pinctrl_pin_dbg_show,
+ .dt_node_to_map = pinconf_generic_dt_node_to_map_pin,
+ .dt_free_map = pinctrl_utils_free_map,
+};
+
+static struct pinctrl_desc aspeed_g4_pinctrl_desc = {
+ .name = "aspeed-g4-pinctrl",
+ .pins = aspeed_g4_pins,
+ .npins = ARRAY_SIZE(aspeed_g4_pins),
+ .pctlops = &aspeed_g4_pinctrl_ops,
+ .pmxops = &aspeed_g4_pinmux_ops,
+};
+
+static int aspeed_g4_pinctrl_probe(struct platform_device *pdev)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(aspeed_g4_pins); i++)
+ aspeed_g4_pins[i].number = i;
+
+ return aspeed_pinctrl_probe(pdev, &aspeed_g4_pinctrl_desc,
+ &aspeed_g4_pinctrl_data);
+}
+
+static const struct of_device_id aspeed_g4_pinctrl_of_match[] = {
+ { .compatible = "aspeed,g4-pinctrl", },
+ { },
+};
+
+static struct platform_driver aspeed_g4_pinctrl_driver = {
+ .probe = aspeed_g4_pinctrl_probe,
+ .driver = {
+ .name = "aspeed-g4-pinctrl",
+ .of_match_table = aspeed_g4_pinctrl_of_match,
+ },
+};
+
+static int aspeed_g4_pinctrl_init(void)
+{
+ return platform_driver_register(&aspeed_g4_pinctrl_driver);
+}
+
+arch_initcall(aspeed_g4_pinctrl_init);
--
2.7.4
^ permalink raw reply related [flat|nested] 28+ messages in thread* [PATCH 04/12] pinctrl: Add pinctrl-aspeed-g5 driver
2016-07-20 5:58 [PATCH 00/12] aspeed: Add pinctrl and gpio drivers Andrew Jeffery
` (2 preceding siblings ...)
2016-07-20 5:58 ` [PATCH 03/12] pinctrl: Add pinctrl-aspeed-g4 driver Andrew Jeffery
@ 2016-07-20 5:58 ` Andrew Jeffery
2016-07-20 5:58 ` [PATCH 05/12] gpio: dt-bindings: Add documentation for Aspeed GPIO controllers Andrew Jeffery
` (7 subsequent siblings)
11 siblings, 0 replies; 28+ messages in thread
From: Andrew Jeffery @ 2016-07-20 5:58 UTC (permalink / raw)
To: Linus Walleij
Cc: Mark Rutland, Alexandre Courbot, devicetree, Andrew Jeffery,
Benjamin Herrenschmidt, Russell King, linux-kernel, linux-gpio,
Rob Herring, Joel Stanley, linux-arm-kernel, Jeremy Kerr
A small subset of pins and functions are exposed. The selection of pins
and functions is driven by the development of OpenBMC[1] on the
AST2500 SoC, particularly around booting the IBM Witherspoon platform.
[1] https://github.com/openbmc/docs
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
---
arch/arm/mach-aspeed/Kconfig | 1 +
drivers/pinctrl/aspeed/Kconfig | 8 +
drivers/pinctrl/aspeed/Makefile | 1 +
drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c | 561 +++++++++++++++++++++++++++++
4 files changed, 571 insertions(+)
create mode 100644 drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c
diff --git a/arch/arm/mach-aspeed/Kconfig b/arch/arm/mach-aspeed/Kconfig
index 2589b90b0a7b..25a0ae01429e 100644
--- a/arch/arm/mach-aspeed/Kconfig
+++ b/arch/arm/mach-aspeed/Kconfig
@@ -25,6 +25,7 @@ config MACH_ASPEED_G5
bool "Aspeed SoC 5th Generation"
depends on ARCH_MULTI_V6
select CPU_V6
+ select PINCTRL_ASPEED_G5
help
Say yes if you intend to run on an Aspeed ast2500 or similar
fifth generation Aspeed BMCs.
diff --git a/drivers/pinctrl/aspeed/Kconfig b/drivers/pinctrl/aspeed/Kconfig
index 480a206c69f1..ee45a965bc68 100644
--- a/drivers/pinctrl/aspeed/Kconfig
+++ b/drivers/pinctrl/aspeed/Kconfig
@@ -14,3 +14,11 @@ config PINCTRL_ASPEED_G4
help
Say Y here to enable pin controller support for Aspeed's 4th
generation AST SoCs. GPIO is provided by a separate GPIO driver.
+
+config PINCTRL_ASPEED_G5
+ bool "Aspeed G5 SoC pin control"
+ depends on (MACH_ASPEED_G5 || COMPILE_TEST) && OF
+ select PINCTRL_ASPEED
+ help
+ Say Y here to enable pin controller support for Aspeed's 5th
+ generation AST SoCs. GPIO is provided by a separate GPIO driver.
diff --git a/drivers/pinctrl/aspeed/Makefile b/drivers/pinctrl/aspeed/Makefile
index 253bddd1fc2d..0f4b8760f936 100644
--- a/drivers/pinctrl/aspeed/Makefile
+++ b/drivers/pinctrl/aspeed/Makefile
@@ -2,3 +2,4 @@
obj-$(CONFIG_PINCTRL_ASPEED) += pinctrl-aspeed.o
obj-$(CONFIG_PINCTRL_ASPEED_G4) += pinctrl-aspeed-g4.o
+obj-$(CONFIG_PINCTRL_ASPEED_G5) += pinctrl-aspeed-g5.o
diff --git a/drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c b/drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c
new file mode 100644
index 000000000000..737a33b05ea2
--- /dev/null
+++ b/drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c
@@ -0,0 +1,561 @@
+/*
+ * Copyright (C) 2016 IBM Corp.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/bitops.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/string.h>
+#include <linux/types.h>
+
+#include "../core.h"
+#include "../pinctrl-utils.h"
+#include "pinctrl-aspeed.h"
+
+#define ASPEED_G5_NR_PINS 228
+
+#define COND1 SIG_DESC_BIT(SCU90, 6, 0)
+#define COND2 { SCU94, GENMASK(1, 0), 0, 0 }
+
+#define I2C9_DESC SIG_DESC_SET(SCU90, 22)
+
+#define C14 4
+SIG_EXPR_LIST_DECL_SINGLE(SCL9, I2C9, I2C9_DESC, COND1);
+SIG_EXPR_LIST_DECL_SINGLE(TIMER5, TIMER5, SIG_DESC_SET(SCU80, 4), COND1);
+MS_PIN_DECL(C14, GPIOA4, SCL9, TIMER5);
+
+FUNC_GROUP_DECL(TIMER5, C14);
+
+#define A13 5
+SIG_EXPR_LIST_DECL_SINGLE(SDA9, I2C9, I2C9_DESC, COND1);
+SIG_EXPR_LIST_DECL_SINGLE(TIMER6, TIMER6, SIG_DESC_SET(SCU80, 5), COND1);
+MS_PIN_DECL(A13, GPIOA5, SDA9, TIMER6);
+
+FUNC_GROUP_DECL(TIMER6, A13);
+
+FUNC_GROUP_DECL(I2C9, C14, A13);
+
+#define SD1_DESC SIG_DESC_SET(SCU90, 0)
+
+#define C12 16
+#define I2C10_DESC SIG_DESC_SET(SCU90, 23)
+SIG_EXPR_LIST_DECL_SINGLE(SD1CLK, SD1, SD1_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(SCL10, I2C10, I2C10_DESC);
+MS_PIN_DECL(C12, GPIOC0, SD1CLK, SCL10);
+
+#define A12 17
+SIG_EXPR_LIST_DECL_SINGLE(SD1CMD, SD1, SD1_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(SDA10, I2C10, I2C10_DESC);
+MS_PIN_DECL(A12, GPIOC1, SD1CMD, SDA10);
+
+FUNC_GROUP_DECL(I2C10, C12, A12);
+
+#define B12 18
+#define I2C11_DESC SIG_DESC_SET(SCU90, 24)
+SIG_EXPR_LIST_DECL_SINGLE(SD1DAT0, SD1, SD1_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(SCL11, I2C11, I2C11_DESC);
+MS_PIN_DECL(B12, GPIOC2, SD1DAT0, SCL11);
+
+#define D9 19
+SIG_EXPR_LIST_DECL_SINGLE(SD1DAT1, SD1, SD1_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(SDA11, I2C11, I2C11_DESC);
+MS_PIN_DECL(D9, GPIOC3, SD1DAT1, SDA11);
+
+FUNC_GROUP_DECL(I2C11, B12, D9);
+
+#define D10 20
+#define I2C12_DESC SIG_DESC_SET(SCU90, 25)
+SIG_EXPR_LIST_DECL_SINGLE(SD1DAT2, SD1, SD1_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(SCL12, I2C12, I2C12_DESC);
+MS_PIN_DECL(D10, GPIOC4, SD1DAT2, SCL12);
+
+#define E12 21
+SIG_EXPR_LIST_DECL_SINGLE(SD1DAT3, SD1, SD1_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(SDA12, I2C12, I2C12_DESC);
+MS_PIN_DECL(E12, GPIOC5, SD1DAT3, SDA12);
+
+FUNC_GROUP_DECL(I2C12, D10, E12);
+
+#define C11 22
+#define I2C13_DESC SIG_DESC_SET(SCU90, 26)
+SIG_EXPR_LIST_DECL_SINGLE(SD1CD, SD1, SD1_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(SCL13, I2C13, I2C13_DESC);
+MS_PIN_DECL(C11, GPIOC6, SD1CD, SCL13);
+
+#define B11 23
+SIG_EXPR_LIST_DECL_SINGLE(SD1WP, SD1, SD1_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(SDA13, I2C13, I2C13_DESC);
+MS_PIN_DECL(B11, GPIOC7, SD1WP, SDA13);
+
+FUNC_GROUP_DECL(I2C13, C11, B11);
+FUNC_GROUP_DECL(SD1, C12, A12, B12, D9, D10, E12, C11, B11);
+
+#define SD2_DESC SIG_DESC_SET(SCU90, 1)
+#define GPID0_DESC SIG_DESC_SET(SCU8C, 8)
+#define GPID_DESC SIG_DESC_SET(HW_STRAP1, 21)
+
+#define F19 24
+SIG_EXPR_LIST_DECL_SINGLE(SD2CLK, SD2, SD2_DESC);
+SIG_EXPR_DECL(GPID0IN, GPID0, GPID0_DESC);
+SIG_EXPR_DECL(GPID0IN, GPID, GPID_DESC);
+SIG_EXPR_LIST_DECL_DUAL(GPID0IN, GPID0, GPID);
+MS_PIN_DECL(F19, GPIOD0, SD2CLK, GPID0IN);
+
+#define E21 25
+SIG_EXPR_LIST_DECL_SINGLE(SD2CMD, SD2, SD2_DESC);
+SIG_EXPR_DECL(GPID0OUT, GPID0, GPID0_DESC);
+SIG_EXPR_DECL(GPID0OUT, GPID, GPID_DESC);
+SIG_EXPR_LIST_DECL_DUAL(GPID0OUT, GPID0, GPID);
+MS_PIN_DECL(E21, GPIOD1, SD2CMD, GPID0OUT);
+
+FUNC_GROUP_DECL(GPID0, F19, E21);
+
+#define GPID1_DESC SIG_DESC_SET(SCU8C, 9)
+
+#define D20 26
+SIG_EXPR_LIST_DECL_SINGLE(SD2DAT0, SD2, SD2_DESC);
+SIG_EXPR_DECL(GPID1IN, GPID1, GPID1_DESC);
+SIG_EXPR_DECL(GPID1IN, GPID, GPID_DESC);
+SIG_EXPR_LIST_DECL_DUAL(GPID1IN, GPID1, GPID);
+MS_PIN_DECL(D20, GPIOD2, SD2DAT0, GPID1IN);
+
+#define D21 27
+SIG_EXPR_LIST_DECL_SINGLE(SD2DAT1, SD2, SD2_DESC);
+SIG_EXPR_DECL(GPID1OUT, GPID1, GPID1_DESC);
+SIG_EXPR_DECL(GPID1OUT, GPID, GPID_DESC);
+SIG_EXPR_LIST_DECL_DUAL(GPID1OUT, GPID1, GPID);
+MS_PIN_DECL(D21, GPIOD3, SD2DAT1, GPID1OUT);
+
+FUNC_GROUP_DECL(GPID1, D20, D21);
+
+#define I2C5_DESC SIG_DESC_SET(SCU90, 18)
+
+#define L3 80
+SIG_EXPR_LIST_DECL_SINGLE(SCL5, I2C5, I2C5_DESC);
+SS_PIN_DECL(L3, GPIOK0, SCL5);
+
+#define L4 81
+SIG_EXPR_LIST_DECL_SINGLE(SDA5, I2C5, I2C5_DESC);
+SS_PIN_DECL(L4, GPIOK1, SDA5);
+
+FUNC_GROUP_DECL(I2C5, L3, L4);
+
+#define I2C6_DESC SIG_DESC_SET(SCU90, 19)
+
+#define L1 82
+SIG_EXPR_LIST_DECL_SINGLE(SCL6, I2C6, I2C6_DESC);
+SS_PIN_DECL(L1, GPIOK2, SCL6);
+
+#define N2 83
+SIG_EXPR_LIST_DECL_SINGLE(SDA6, I2C6, I2C6_DESC);
+SS_PIN_DECL(N2, GPIOK3, SDA6);
+
+FUNC_GROUP_DECL(I2C6, L1, N2);
+
+#define I2C7_DESC SIG_DESC_SET(SCU90, 20)
+
+#define N1 84
+SIG_EXPR_LIST_DECL_SINGLE(SCL7, I2C7, I2C7_DESC);
+SS_PIN_DECL(N1, GPIOK4, SCL7);
+
+#define P1 85
+SIG_EXPR_LIST_DECL_SINGLE(SDA7, I2C7, I2C7_DESC);
+SS_PIN_DECL(P1, GPIOK5, SDA7);
+
+FUNC_GROUP_DECL(I2C7, N1, P1);
+
+#define I2C8_DESC SIG_DESC_SET(SCU90, 21)
+
+#define P2 86
+SIG_EXPR_LIST_DECL_SINGLE(SCL8, I2C8, I2C8_DESC);
+SS_PIN_DECL(P2, GPIOK6, SCL8);
+
+#define R1 87
+SIG_EXPR_LIST_DECL_SINGLE(SDA8, I2C8, I2C8_DESC);
+SS_PIN_DECL(R1, GPIOK7, SDA8);
+
+FUNC_GROUP_DECL(I2C8, P2, R1);
+
+#define VPIOFF0_DESC { SCU90, GENMASK(5, 4), 0, 0 }
+#define VPIOFF1_DESC { SCU90, GENMASK(5, 4), 1, 0 }
+#define VPI24_DESC { SCU90, GENMASK(5, 4), 2, 0 }
+#define VPIRSVD_DESC { SCU90, GENMASK(5, 4), 3, 0 }
+
+#define V2 104
+#define V2_DESC SIG_DESC_SET(SCU88, 0)
+SIG_EXPR_LIST_DECL_SINGLE(DASHN0, DASHN0, VPIRSVD_DESC, V2_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(PWM0, PWM0, V2_DESC, COND2);
+MS_PIN_DECL(V2, GPION0, DASHN0, PWM0);
+FUNC_GROUP_DECL(PWM0, V2);
+
+#define W2 105
+#define W2_DESC SIG_DESC_SET(SCU88, 1)
+SIG_EXPR_LIST_DECL_SINGLE(DASHN1, DASHN1, VPIRSVD_DESC, W2_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(PWM1, PWM1, W2_DESC, COND2);
+MS_PIN_DECL(W2, GPION1, DASHN1, PWM1);
+FUNC_GROUP_DECL(PWM1, W2);
+
+#define V3 106
+#define V3_DESC SIG_DESC_SET(SCU88, 2)
+SIG_EXPR_DECL(VPIG2, VPI24, VPI24_DESC, V3_DESC, COND2);
+SIG_EXPR_DECL(VPIG2, VPIRSVD, VPIRSVD_DESC, V3_DESC, COND2);
+SIG_EXPR_LIST_DECL_DUAL(VPIG2, VPI24, VPIRSVD);
+SIG_EXPR_LIST_DECL_SINGLE(PWM2, PWM2, V3_DESC, COND2);
+MS_PIN_DECL(V3, GPION2, VPIG2, PWM2);
+FUNC_GROUP_DECL(PWM2, V3);
+
+#define U3 107
+#define U3_DESC SIG_DESC_SET(SCU88, 3)
+SIG_EXPR_DECL(VPIG3, VPI24, VPI24_DESC, U3_DESC, COND2);
+SIG_EXPR_DECL(VPIG3, VPIRSVD, VPIRSVD_DESC, U3_DESC, COND2);
+SIG_EXPR_LIST_DECL_DUAL(VPIG3, VPI24, VPIRSVD);
+SIG_EXPR_LIST_DECL_SINGLE(PWM3, PWM3, U3_DESC, COND2);
+MS_PIN_DECL(U3, GPION3, VPIG3, PWM3);
+FUNC_GROUP_DECL(PWM3, U3);
+
+#define W3 108
+#define W3_DESC SIG_DESC_SET(SCU88, 4)
+SIG_EXPR_DECL(VPIG4, VPI24, VPI24_DESC, W3_DESC, COND2);
+SIG_EXPR_DECL(VPIG4, VPIRSVD, VPIRSVD_DESC, W3_DESC, COND2);
+SIG_EXPR_LIST_DECL_DUAL(VPIG4, VPI24, VPIRSVD);
+SIG_EXPR_LIST_DECL_SINGLE(PWM4, PWM4, W3_DESC, COND2);
+MS_PIN_DECL(W3, GPION4, VPIG4, PWM4);
+FUNC_GROUP_DECL(PWM4, W3);
+
+#define AA3 109
+#define AA3_DESC SIG_DESC_SET(SCU88, 5)
+SIG_EXPR_DECL(VPIG5, VPI24, VPI24_DESC, AA3_DESC, COND2);
+SIG_EXPR_DECL(VPIG5, VPIRSVD, VPIRSVD_DESC, AA3_DESC, COND2);
+SIG_EXPR_LIST_DECL_DUAL(VPIG5, VPI24, VPIRSVD);
+SIG_EXPR_LIST_DECL_SINGLE(PWM5, PWM5, AA3_DESC, COND2);
+MS_PIN_DECL(AA3, GPION5, VPIG5, PWM5);
+FUNC_GROUP_DECL(PWM5, AA3);
+
+#define Y3 110
+#define Y3_DESC SIG_DESC_SET(SCU88, 6)
+SIG_EXPR_LIST_DECL_SINGLE(VPIG6, VPI24, VPI24_DESC, Y3_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(PWM6, PWM6, Y3_DESC, COND2);
+MS_PIN_DECL(Y3, GPION6, VPIG6, PWM6);
+FUNC_GROUP_DECL(PWM6, Y3);
+
+#define T4 111
+#define T4_DESC SIG_DESC_SET(SCU88, 7)
+SIG_EXPR_LIST_DECL_SINGLE(VPIG7, VPI24, VPI24_DESC, T4_DESC);
+SIG_EXPR_LIST_DECL_SINGLE(PWM7, PWM7, T4_DESC, COND2);
+MS_PIN_DECL(T4, GPION7, VPIG7, PWM7);
+FUNC_GROUP_DECL(PWM7, T4);
+
+#define I2C3_DESC SIG_DESC_SET(SCU90, 16)
+
+#define A11 128
+SIG_EXPR_LIST_DECL_SINGLE(SCL3, I2C3, I2C3_DESC);
+SS_PIN_DECL(A11, GPIOQ0, SCL3);
+
+#define A10 129
+SIG_EXPR_LIST_DECL_SINGLE(SDA3, I2C3, I2C3_DESC);
+SS_PIN_DECL(A10, GPIOQ1, SDA3);
+
+FUNC_GROUP_DECL(I2C3, A11, A10);
+
+#define I2C4_DESC SIG_DESC_SET(SCU90, 17)
+
+#define A9 130
+SIG_EXPR_LIST_DECL_SINGLE(SCL4, I2C4, I2C4_DESC);
+SS_PIN_DECL(A9, GPIOQ2, SCL4);
+
+#define B9 131
+SIG_EXPR_LIST_DECL_SINGLE(SDA4, I2C4, I2C4_DESC);
+SS_PIN_DECL(B9, GPIOQ3, SDA4);
+
+FUNC_GROUP_DECL(I2C4, A9, B9);
+
+#define I2C14_DESC SIG_DESC_SET(SCU90, 27)
+
+#define N21 132
+SIG_EXPR_LIST_DECL_SINGLE(SCL14, I2C14, I2C14_DESC);
+SS_PIN_DECL(N21, GPIOQ4, SCL14);
+
+#define N22 133
+SIG_EXPR_LIST_DECL_SINGLE(SDA14, I2C14, I2C14_DESC);
+SS_PIN_DECL(N22, GPIOQ5, SDA14);
+
+FUNC_GROUP_DECL(I2C14, N21, N22);
+
+/* RGMII1/RMII1 */
+
+#define MAC1_RMII { HW_STRAP1, BIT(6), 0, 0 }
+
+#define B5 152
+SIG_EXPR_LIST_DECL_SINGLE(GPIOT0, GPIOT0, SIG_DESC_SET(SCUA0, 0));
+SIG_EXPR_LIST_DECL_SINGLE(RMII1RCLKO, RMII1, MAC1_RMII,
+ SIG_DESC_SET(SCU48, 29));
+SIG_EXPR_LIST_DECL_SINGLE(RGMII1TXCK, RGMII1);
+MS_PIN_DECL_(B5, SIG_EXPR_LIST_PTR(GPIOT0), SIG_EXPR_LIST_PTR(RMII1RCLKO),
+ SIG_EXPR_LIST_PTR(RGMII1TXCK));
+
+#define E9 153
+SIG_EXPR_LIST_DECL_SINGLE(GPIOT1, GPIOT1, SIG_DESC_SET(SCUA0, 1));
+SIG_EXPR_LIST_DECL_SINGLE(RMII1TXEN, RMII1, MAC1_RMII);
+SIG_EXPR_LIST_DECL_SINGLE(RGMII1TXCTL, RGMII1);
+MS_PIN_DECL_(E9, SIG_EXPR_LIST_PTR(GPIOT1), SIG_EXPR_LIST_PTR(RMII1TXEN),
+ SIG_EXPR_LIST_PTR(RGMII1TXCTL));
+
+#define F9 154
+SIG_EXPR_LIST_DECL_SINGLE(GPIOT2, GPIOT2, SIG_DESC_SET(SCUA0, 2));
+SIG_EXPR_LIST_DECL_SINGLE(RMII1TXD0, RMII1, MAC1_RMII);
+SIG_EXPR_LIST_DECL_SINGLE(RGMII1TXD0, RGMII1);
+MS_PIN_DECL_(F9, SIG_EXPR_LIST_PTR(GPIOT2), SIG_EXPR_LIST_PTR(RMII1TXD0),
+ SIG_EXPR_LIST_PTR(RGMII1TXD0));
+
+#define A5 155
+SIG_EXPR_LIST_DECL_SINGLE(GPIOT3, GPIOT3, SIG_DESC_SET(SCUA0, 3));
+SIG_EXPR_LIST_DECL_SINGLE(RMII1TXD1, RMII1, MAC1_RMII);
+SIG_EXPR_LIST_DECL_SINGLE(RGMII1TXD1, RGMII1);
+MS_PIN_DECL_(A5, SIG_EXPR_LIST_PTR(GPIOT3), SIG_EXPR_LIST_PTR(RMII1TXD1),
+ SIG_EXPR_LIST_PTR(RGMII1TXD1));
+
+#define E7 156
+SIG_EXPR_LIST_DECL_SINGLE(GPIOT4, GPIOT4, SIG_DESC_SET(SCUA0, 4));
+SIG_EXPR_LIST_DECL_SINGLE(RMII1DASH0, RMII1, MAC1_RMII);
+SIG_EXPR_LIST_DECL_SINGLE(RGMII1TXD2, RGMII1);
+MS_PIN_DECL_(E7, SIG_EXPR_LIST_PTR(GPIOT4), SIG_EXPR_LIST_PTR(RMII1DASH0),
+ SIG_EXPR_LIST_PTR(RGMII1TXD2));
+
+#define D7 157
+SIG_EXPR_LIST_DECL_SINGLE(GPIOT5, GPIOT5, SIG_DESC_SET(SCUA0, 5));
+SIG_EXPR_LIST_DECL_SINGLE(RMII1DASH1, RMII1, MAC1_RMII);
+SIG_EXPR_LIST_DECL_SINGLE(RGMII1TXD3, RGMII1);
+MS_PIN_DECL_(D7, SIG_EXPR_LIST_PTR(GPIOT5), SIG_EXPR_LIST_PTR(RMII1DASH1),
+ SIG_EXPR_LIST_PTR(RGMII1TXD3));
+
+#define B4 164
+SIG_EXPR_LIST_DECL_SINGLE(GPIOU4, GPIOU4, SIG_DESC_SET(SCUA0, 12));
+SIG_EXPR_LIST_DECL_SINGLE(RMII1RCLKI, RMII1, MAC1_RMII);
+SIG_EXPR_LIST_DECL_SINGLE(RGMII1RXCK, RGMII1);
+MS_PIN_DECL_(B4, SIG_EXPR_LIST_PTR(GPIOU4), SIG_EXPR_LIST_PTR(RMII1RCLKI),
+ SIG_EXPR_LIST_PTR(RGMII1RXCK));
+
+#define A4 165
+SIG_EXPR_LIST_DECL_SINGLE(GPIOU5, GPIOU5, SIG_DESC_SET(SCUA0, 13));
+SIG_EXPR_LIST_DECL_SINGLE(RMII1DASH2, RMII1, MAC1_RMII);
+SIG_EXPR_LIST_DECL_SINGLE(RGMII1RXCTL, RGMII1);
+MS_PIN_DECL_(A4, SIG_EXPR_LIST_PTR(GPIOU5), SIG_EXPR_LIST_PTR(RMII1DASH2),
+ SIG_EXPR_LIST_PTR(RGMII1RXCTL));
+
+#define A3 166
+SIG_EXPR_LIST_DECL_SINGLE(GPIOU6, GPIOU6, SIG_DESC_SET(SCUA0, 14));
+SIG_EXPR_LIST_DECL_SINGLE(RMII1RXD0, RMII1, MAC1_RMII);
+SIG_EXPR_LIST_DECL_SINGLE(RGMII1RXD0, RGMII1);
+MS_PIN_DECL_(A3, SIG_EXPR_LIST_PTR(GPIOU6), SIG_EXPR_LIST_PTR(RMII1RXD0),
+ SIG_EXPR_LIST_PTR(RGMII1RXD0));
+
+#define D6 167
+SIG_EXPR_LIST_DECL_SINGLE(GPIOU7, GPIOU7, SIG_DESC_SET(SCUA0, 15));
+SIG_EXPR_LIST_DECL_SINGLE(RMII1RXD1, RMII1, MAC1_RMII);
+SIG_EXPR_LIST_DECL_SINGLE(RGMII1RXD1, RGMII1);
+MS_PIN_DECL_(D6, SIG_EXPR_LIST_PTR(GPIOU7), SIG_EXPR_LIST_PTR(RMII1RXD1),
+ SIG_EXPR_LIST_PTR(RGMII1RXD1));
+
+#define C5 168
+SIG_EXPR_LIST_DECL_SINGLE(GPIOV0, GPIOV0, SIG_DESC_SET(SCUA0, 16));
+SIG_EXPR_LIST_DECL_SINGLE(RMII1CRSDV, RMII1, MAC1_RMII);
+SIG_EXPR_LIST_DECL_SINGLE(RGMII1RXD2, RGMII1);
+MS_PIN_DECL_(C5, SIG_EXPR_LIST_PTR(GPIOV0), SIG_EXPR_LIST_PTR(RMII1CRSDV),
+ SIG_EXPR_LIST_PTR(RGMII1RXD2));
+
+#define C4 169
+SIG_EXPR_LIST_DECL_SINGLE(GPIOV1, GPIOV1, SIG_DESC_SET(SCUA0, 17));
+SIG_EXPR_LIST_DECL_SINGLE(RMII1RXER, RMII1, MAC1_RMII);
+SIG_EXPR_LIST_DECL_SINGLE(RGMII1RXD3, RGMII1);
+MS_PIN_DECL_(C4, SIG_EXPR_LIST_PTR(GPIOV1), SIG_EXPR_LIST_PTR(RMII1RXER),
+ SIG_EXPR_LIST_PTR(RGMII1RXD3));
+
+FUNC_GROUP_DECL(RGMII1, B4, A4, A3, D6, C5, C4, B5, E9, F9, A5, E7, D7);
+FUNC_GROUP_DECL(RMII1, B4, A3, D6, C5, C4, B5, E9, F9, A5);
+
+static struct pinctrl_pin_desc aspeed_g5_pins[ASPEED_G5_NR_PINS] = {
+ ASPEED_PINCTRL_PIN(C14),
+ ASPEED_PINCTRL_PIN(A13),
+ ASPEED_PINCTRL_PIN(C12),
+ ASPEED_PINCTRL_PIN(A12),
+ ASPEED_PINCTRL_PIN(B12),
+ ASPEED_PINCTRL_PIN(D9),
+ ASPEED_PINCTRL_PIN(D10),
+ ASPEED_PINCTRL_PIN(E12),
+ ASPEED_PINCTRL_PIN(C11),
+ ASPEED_PINCTRL_PIN(B11),
+ ASPEED_PINCTRL_PIN(F19),
+ ASPEED_PINCTRL_PIN(E21),
+ ASPEED_PINCTRL_PIN(D20),
+ ASPEED_PINCTRL_PIN(D21),
+ ASPEED_PINCTRL_PIN(L3),
+ ASPEED_PINCTRL_PIN(L4),
+ ASPEED_PINCTRL_PIN(L1),
+ ASPEED_PINCTRL_PIN(N2),
+ ASPEED_PINCTRL_PIN(N1),
+ ASPEED_PINCTRL_PIN(P1),
+ ASPEED_PINCTRL_PIN(P2),
+ ASPEED_PINCTRL_PIN(R1),
+ ASPEED_PINCTRL_PIN(V2),
+ ASPEED_PINCTRL_PIN(W2),
+ ASPEED_PINCTRL_PIN(V3),
+ ASPEED_PINCTRL_PIN(U3),
+ ASPEED_PINCTRL_PIN(W3),
+ ASPEED_PINCTRL_PIN(AA3),
+ ASPEED_PINCTRL_PIN(Y3),
+ ASPEED_PINCTRL_PIN(T4),
+ ASPEED_PINCTRL_PIN(A11),
+ ASPEED_PINCTRL_PIN(A10),
+ ASPEED_PINCTRL_PIN(A9),
+ ASPEED_PINCTRL_PIN(B9),
+ ASPEED_PINCTRL_PIN(N21),
+ ASPEED_PINCTRL_PIN(N22),
+ ASPEED_PINCTRL_PIN(D10),
+ ASPEED_PINCTRL_PIN(E12),
+ ASPEED_PINCTRL_PIN(B4),
+ ASPEED_PINCTRL_PIN(A4),
+ ASPEED_PINCTRL_PIN(A3),
+ ASPEED_PINCTRL_PIN(D6),
+ ASPEED_PINCTRL_PIN(C5),
+ ASPEED_PINCTRL_PIN(C4),
+ ASPEED_PINCTRL_PIN(B5),
+ ASPEED_PINCTRL_PIN(E9),
+ ASPEED_PINCTRL_PIN(F9),
+ ASPEED_PINCTRL_PIN(A5),
+ ASPEED_PINCTRL_PIN(E7),
+ ASPEED_PINCTRL_PIN(D7),
+};
+
+static const struct aspeed_pin_group aspeed_g5_groups[] = {
+ ASPEED_PINCTRL_GROUP(I2C9),
+ ASPEED_PINCTRL_GROUP(I2C10),
+ ASPEED_PINCTRL_GROUP(I2C11),
+ ASPEED_PINCTRL_GROUP(I2C12),
+ ASPEED_PINCTRL_GROUP(I2C13),
+ ASPEED_PINCTRL_GROUP(SD1),
+ ASPEED_PINCTRL_GROUP(GPID0),
+ ASPEED_PINCTRL_GROUP(GPID1),
+ ASPEED_PINCTRL_GROUP(I2C5),
+ ASPEED_PINCTRL_GROUP(I2C6),
+ ASPEED_PINCTRL_GROUP(I2C7),
+ ASPEED_PINCTRL_GROUP(I2C8),
+ ASPEED_PINCTRL_GROUP(PWM0),
+ ASPEED_PINCTRL_GROUP(PWM1),
+ ASPEED_PINCTRL_GROUP(PWM2),
+ ASPEED_PINCTRL_GROUP(PWM3),
+ ASPEED_PINCTRL_GROUP(PWM4),
+ ASPEED_PINCTRL_GROUP(PWM5),
+ ASPEED_PINCTRL_GROUP(PWM6),
+ ASPEED_PINCTRL_GROUP(PWM7),
+ ASPEED_PINCTRL_GROUP(I2C3),
+ ASPEED_PINCTRL_GROUP(I2C4),
+ ASPEED_PINCTRL_GROUP(I2C14),
+ ASPEED_PINCTRL_GROUP(RMII1),
+ ASPEED_PINCTRL_GROUP(RGMII1),
+};
+
+static const struct aspeed_pin_function aspeed_g5_functions[] = {
+ ASPEED_PINCTRL_FUNC(I2C9),
+ ASPEED_PINCTRL_FUNC(I2C10),
+ ASPEED_PINCTRL_FUNC(I2C11),
+ ASPEED_PINCTRL_FUNC(I2C12),
+ ASPEED_PINCTRL_FUNC(I2C13),
+ ASPEED_PINCTRL_FUNC(SD1),
+ ASPEED_PINCTRL_FUNC(GPID0),
+ ASPEED_PINCTRL_FUNC(GPID1),
+ ASPEED_PINCTRL_FUNC(I2C5),
+ ASPEED_PINCTRL_FUNC(I2C6),
+ ASPEED_PINCTRL_FUNC(I2C7),
+ ASPEED_PINCTRL_FUNC(I2C8),
+ ASPEED_PINCTRL_FUNC(PWM0),
+ ASPEED_PINCTRL_FUNC(PWM1),
+ ASPEED_PINCTRL_FUNC(PWM2),
+ ASPEED_PINCTRL_FUNC(PWM3),
+ ASPEED_PINCTRL_FUNC(PWM4),
+ ASPEED_PINCTRL_FUNC(PWM5),
+ ASPEED_PINCTRL_FUNC(PWM6),
+ ASPEED_PINCTRL_FUNC(PWM7),
+ ASPEED_PINCTRL_FUNC(I2C3),
+ ASPEED_PINCTRL_FUNC(I2C4),
+ ASPEED_PINCTRL_FUNC(I2C14),
+ ASPEED_PINCTRL_FUNC(RMII1),
+ ASPEED_PINCTRL_FUNC(RGMII1),
+};
+
+static struct aspeed_pinctrl_data aspeed_g5_pinctrl_data = {
+ .pins = aspeed_g5_pins,
+ .npins = ARRAY_SIZE(aspeed_g5_pins),
+ .groups = aspeed_g5_groups,
+ .ngroups = ARRAY_SIZE(aspeed_g5_groups),
+ .functions = aspeed_g5_functions,
+ .nfunctions = ARRAY_SIZE(aspeed_g5_functions),
+};
+
+static struct pinmux_ops aspeed_g5_pinmux_ops = {
+ .get_functions_count = aspeed_pinmux_get_fn_count,
+ .get_function_name = aspeed_pinmux_get_fn_name,
+ .get_function_groups = aspeed_pinmux_get_fn_groups,
+ .set_mux = aspeed_pinmux_set_mux,
+ .gpio_request_enable = aspeed_gpio_request_enable,
+ .strict = true,
+};
+
+static struct pinctrl_ops aspeed_g5_pinctrl_ops = {
+ .get_groups_count = aspeed_pinctrl_get_groups_count,
+ .get_group_name = aspeed_pinctrl_get_group_name,
+ .get_group_pins = aspeed_pinctrl_get_group_pins,
+ .pin_dbg_show = aspeed_pinctrl_pin_dbg_show,
+ .dt_node_to_map = pinconf_generic_dt_node_to_map_pin,
+ .dt_free_map = pinctrl_utils_free_map,
+};
+
+static struct pinctrl_desc aspeed_g5_pinctrl_desc = {
+ .name = "aspeed-g5-pinctrl",
+ .pins = aspeed_g5_pins,
+ .npins = ARRAY_SIZE(aspeed_g5_pins),
+ .pctlops = &aspeed_g5_pinctrl_ops,
+ .pmxops = &aspeed_g5_pinmux_ops,
+};
+
+static int aspeed_g5_pinctrl_probe(struct platform_device *pdev)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(aspeed_g5_pins); i++)
+ aspeed_g5_pins[i].number = i;
+
+ return aspeed_pinctrl_probe(pdev, &aspeed_g5_pinctrl_desc,
+ &aspeed_g5_pinctrl_data);
+}
+
+static const struct of_device_id aspeed_g5_pinctrl_of_match[] = {
+ { .compatible = "aspeed,g5-pinctrl", },
+ { },
+};
+
+static struct platform_driver aspeed_g5_pinctrl_driver = {
+ .probe = aspeed_g5_pinctrl_probe,
+ .driver = {
+ .name = "aspeed-g5-pinctrl",
+ .of_match_table = aspeed_g5_pinctrl_of_match,
+ },
+};
+
+static int aspeed_g5_pinctrl_init(void)
+{
+ return platform_driver_register(&aspeed_g5_pinctrl_driver);
+}
+
+arch_initcall(aspeed_g5_pinctrl_init);
--
2.7.4
^ permalink raw reply related [flat|nested] 28+ messages in thread