[PATCH 0/3][v2] pinctrl: qcom: add support for sparse GPIOs

[PATCH 0/3][v2] pinctrl: qcom: add support for sparse GPIOs

[Timur Tabi]

First patch update gpiolib so that it requests the GPIO before trying to
initialize it.

Second patch allows for for pinctrl-msm to understand GPIO groups with
no pins.  Such pins are "hidden" and can't be exported or accessed.

Last patch updates the QDF2xxx driver to take advantage of all that.


Timur Tabi (3):
  gliolib: request the gpio before querying its direction
  [v2] pinctrl: qcom: disable GPIO groups with no pins
  [v2] pinctrl: qcom: qdf2xxx: add support for new ACPI HID QCOM8002

 drivers/gpio/gpiolib.c                 |  11 +++
 drivers/pinctrl/qcom/pinctrl-msm.c     |  22 ++++--
 drivers/pinctrl/qcom/pinctrl-qdf2xxx.c | 139 ++++++++++++++++++++++++---------
 3 files changed, 131 insertions(+), 41 deletions(-)

-- 
Qualcomm Datacenter Technologies, Inc. as an affiliate of Qualcomm
Technologies, Inc.  Qualcomm Technologies, Inc. is a member of the
Code Aurora Forum, a Linux Foundation Collaborative Project.

[PATCH 1/3] gliolib: request the gpio before querying its direction

[Timur Tabi]

Before querying a GPIO to determine its direction, the GPIO should be
formally requested.  This allows the GPIO driver to block access to
unavailable GPIOs, which makes it easier for some drivers to support
sparse GPIO maps.

Signed-off-by: Timur Tabi <timur@codeaurora.org>
---
 drivers/gpio/gpiolib.c | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/drivers/gpio/gpiolib.c b/drivers/gpio/gpiolib.c
index 9568708..3b4e1e8 100644
--- a/drivers/gpio/gpiolib.c
+++ b/drivers/gpio/gpiolib.c
@@ -1202,6 +1202,14 @@ int gpiochip_add_data(struct gpio_chip *chip, void *data)
 		struct gpio_desc *desc = &gdev->descs[i];
 
 		desc->gdev = gdev;
+
+		if (chip->request) {
+			status = chip->request(chip, i);
+			if (status < 0)
+				/* The GPIO is unavailable, so skip it */
+				continue;
+		}
+
 		/*
 		 * REVISIT: most hardware initializes GPIOs as inputs
 		 * (often with pullups enabled) so power usage is
@@ -1227,6 +1235,9 @@ int gpiochip_add_data(struct gpio_chip *chip, void *data)
 			 */
 			set_bit(FLAG_IS_OUT, &desc->flags);
 		}
+
+		if (chip->free)
+			chip->free(chip, i);
 	}
 
 #ifdef CONFIG_PINCTRL
-- 
Qualcomm Datacenter Technologies, Inc. as an affiliate of Qualcomm
Technologies, Inc.  Qualcomm Technologies, Inc. is a member of the
Code Aurora Forum, a Linux Foundation Collaborative Project.

[PATCH 2/3] [v2] pinctrl: qcom: disable GPIO groups with no pins

[Timur Tabi]

To support sparse GPIO maps, pinctrl-msm client drivers can specify
that a given GPIO has a pin count of zero.  These GPIOs will be
considered "hidden".  Any attempt to claim the GPIO will fail, and they
will not be listed in debugfs.

Signed-off-by: Timur Tabi <timur@codeaurora.org>
---
 drivers/pinctrl/qcom/pinctrl-msm.c | 22 +++++++++++++++++-----
 1 file changed, 17 insertions(+), 5 deletions(-)

diff --git a/drivers/pinctrl/qcom/pinctrl-msm.c b/drivers/pinctrl/qcom/pinctrl-msm.c
index 273badd..d0f09a3 100644
--- a/drivers/pinctrl/qcom/pinctrl-msm.c
+++ b/drivers/pinctrl/qcom/pinctrl-msm.c
@@ -494,6 +494,11 @@ static void msm_gpio_dbg_show_one(struct seq_file *s,
 	};
 
 	g = &pctrl->soc->groups[offset];
+
+	/* If the GPIO group has no pins, then don't show it. */
+	if (!g->npins)
+		return;
+
 	ctl_reg = readl(pctrl->regs + g->ctl_reg);
 
 	is_out = !!(ctl_reg & BIT(g->oe_bit));
@@ -503,7 +508,7 @@ static void msm_gpio_dbg_show_one(struct seq_file *s,
 
 	seq_printf(s, " %-8s: %-3s %d", g->name, is_out ? "out" : "in", func);
 	seq_printf(s, " %dmA", msm_regval_to_drive(drive));
-	seq_printf(s, " %s", pulls[pull]);
+	seq_printf(s, " %s\n", pulls[pull]);
 }
 
 static void msm_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip)
@@ -511,23 +516,30 @@ static void msm_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip)
 	unsigned gpio = chip->base;
 	unsigned i;
 
-	for (i = 0; i < chip->ngpio; i++, gpio++) {
+	for (i = 0; i < chip->ngpio; i++, gpio++)
 		msm_gpio_dbg_show_one(s, NULL, chip, i, gpio);
-		seq_puts(s, "\n");
-	}
 }
 
 #else
 #define msm_gpio_dbg_show NULL
 #endif
 
+/* If the GPIO has no pins, then treat it as unavailable. */
+static int msm_gpio_request(struct gpio_chip *chip, unsigned int offset)
+{
+	struct msm_pinctrl *pctrl = gpiochip_get_data(chip);
+	const struct msm_pingroup *g = &pctrl->soc->groups[offset];
+
+	return g->npins ? 0 : -ENODEV;
+}
+
 static struct gpio_chip msm_gpio_template = {
 	.direction_input  = msm_gpio_direction_input,
 	.direction_output = msm_gpio_direction_output,
 	.get_direction    = msm_gpio_get_direction,
 	.get              = msm_gpio_get,
 	.set              = msm_gpio_set,
-	.request          = gpiochip_generic_request,
+	.request          = msm_gpio_request,
 	.free             = gpiochip_generic_free,
 	.dbg_show         = msm_gpio_dbg_show,
 };
-- 
Qualcomm Datacenter Technologies, Inc. as an affiliate of Qualcomm
Technologies, Inc.  Qualcomm Technologies, Inc. is a member of the
Code Aurora Forum, a Linux Foundation Collaborative Project.

[PATCH 3/3] [v2] pinctrl: qcom: qdf2xxx: add support for new ACPI HID QCOM8002

[Timur Tabi]

Newer versions of the firmware for the Qualcomm Datacenter Technologies
QDF2400 restricts access to a subset of the GPIOs on the TLMM.  To
prevent older kernels from accidentally accessing the restricted GPIOs,
we change the ACPI HID for the TLMM block from QCOM8001 to QCOM8002,
and introduce a new property "gpios".  This property is an array of
specific GPIOs that are accessible.  When an older kernel boots on
newer (restricted) firmware, it will fail to probe.

To implement the sparse GPIO map, we register all of the GPIOs, but set
the pin count for the unavailable GPIOs to zero.  The pinctrl-msm
driver will block those unavailable GPIOs from being accessed.

To allow newer kernels to support older firmware, the driver retains
support for QCOM8001.

Signed-off-by: Timur Tabi <timur@codeaurora.org>
---
 drivers/pinctrl/qcom/pinctrl-qdf2xxx.c | 139 ++++++++++++++++++++++++---------
 1 file changed, 103 insertions(+), 36 deletions(-)

diff --git a/drivers/pinctrl/qcom/pinctrl-qdf2xxx.c b/drivers/pinctrl/qcom/pinctrl-qdf2xxx.c
index bb3ce5c..e3b58c4 100644
--- a/drivers/pinctrl/qcom/pinctrl-qdf2xxx.c
+++ b/drivers/pinctrl/qcom/pinctrl-qdf2xxx.c
@@ -38,68 +38,141 @@
 /* maximum size of each gpio name (enough room for "gpioXXX" + null) */
 #define NAME_SIZE	8
 
+enum {
+	QDF2XXX_V1,
+	QDF2XXX_V2,
+};
+
+static const struct acpi_device_id qdf2xxx_acpi_ids[] = {
+	{"QCOM8001", QDF2XXX_V1},
+	{"QCOM8002", QDF2XXX_V2},
+	{},
+};
+MODULE_DEVICE_TABLE(acpi, qdf2xxx_acpi_ids);
+
 static int qdf2xxx_pinctrl_probe(struct platform_device *pdev)
 {
+	const struct acpi_device_id *id =
+		acpi_match_device(qdf2xxx_acpi_ids, &pdev->dev);
 	struct pinctrl_pin_desc *pins;
 	struct msm_pingroup *groups;
 	char (*names)[NAME_SIZE];
 	unsigned int i;
 	u32 num_gpios;
+	unsigned int avail_gpios; /* The number of GPIOs we support */
+	u16 *gpios; /* An array of supported GPIOs */
 	int ret;
 
 	/* Query the number of GPIOs from ACPI */
 	ret = device_property_read_u32(&pdev->dev, "num-gpios", &num_gpios);
 	if (ret < 0) {
-		dev_warn(&pdev->dev, "missing num-gpios property\n");
+		dev_err(&pdev->dev, "missing 'num-gpios' property\n");
 		return ret;
 	}
-
 	if (!num_gpios || num_gpios > MAX_GPIOS) {
-		dev_warn(&pdev->dev, "invalid num-gpios property\n");
+		dev_err(&pdev->dev, "invalid 'num-gpios' property\n");
 		return -ENODEV;
 	}
 
+	/*
+	 * The QCOM8001 HID contains only the number of GPIOs, and assumes
+	 * that all of them are available. avail_gpios is the same as num_gpios.
+	 *
+	 * The QCOM8002 HID introduces the 'gpios' DSD, which lists
+	 * specific GPIOs that the driver is allowed to access.
+	 *
+	 * The make the common code simpler, in both cases we create an
+	 * array of GPIOs that are accessible.  So for QCOM8001, that would
+	 * be all of the GPIOs.
+	 */
+	if (id->driver_data == QDF2XXX_V1) {
+		avail_gpios = num_gpios;
+
+		gpios = devm_kcalloc(&pdev->dev, avail_gpios, sizeof(gpios[0]),
+				     GFP_KERNEL);
+		if (!gpios)
+			return -ENOMEM;
+
+		for (i = 0; i < avail_gpios; i++)
+			gpios[i] = i;
+	} else {
+		/* The number of GPIOs in the approved list */
+		ret = device_property_read_u16_array(&pdev->dev, "gpios",
+						     NULL, 0);
+		if (ret < 0) {
+			dev_err(&pdev->dev, "missing 'num-gpios' property\n");
+			return ret;
+		}
+		if (!ret || ret > MAX_GPIOS) {
+			dev_err(&pdev->dev, "invalid 'num-gpios' property\n");
+			return -ENODEV;
+		}
+		avail_gpios = ret;
+
+		gpios = devm_kcalloc(&pdev->dev, avail_gpios, sizeof(gpios[0]),
+				     GFP_KERNEL);
+		if (!gpios)
+			return -ENOMEM;
+
+		ret = device_property_read_u16_array(&pdev->dev, "gpios", gpios,
+						     avail_gpios);
+		if (ret < 0) {
+			dev_err(&pdev->dev, "could not read list of GPIOs\n");
+			return ret;
+		}
+	}
+
 	pins = devm_kcalloc(&pdev->dev, num_gpios,
 		sizeof(struct pinctrl_pin_desc), GFP_KERNEL);
 	groups = devm_kcalloc(&pdev->dev, num_gpios,
 		sizeof(struct msm_pingroup), GFP_KERNEL);
-	names = devm_kcalloc(&pdev->dev, num_gpios, NAME_SIZE, GFP_KERNEL);
+	names = devm_kcalloc(&pdev->dev, avail_gpios, NAME_SIZE, GFP_KERNEL);
 
 	if (!pins || !groups || !names)
 		return -ENOMEM;
 
+	/*
+	 * Initialize the array.  GPIOs not listed in the 'gpios' array
+	 * still need a number, but nothing else.
+	 */
 	for (i = 0; i < num_gpios; i++) {
-		snprintf(names[i], NAME_SIZE, "gpio%u", i);
-
 		pins[i].number = i;
-		pins[i].name = names[i];
-
-		groups[i].npins = 1;
-		groups[i].name = names[i];
 		groups[i].pins = &pins[i].number;
+	}
 
-		groups[i].ctl_reg = 0x10000 * i;
-		groups[i].io_reg = 0x04 + 0x10000 * i;
-		groups[i].intr_cfg_reg = 0x08 + 0x10000 * i;
-		groups[i].intr_status_reg = 0x0c + 0x10000 * i;
-		groups[i].intr_target_reg = 0x08 + 0x10000 * i;
-
-		groups[i].mux_bit = 2;
-		groups[i].pull_bit = 0;
-		groups[i].drv_bit = 6;
-		groups[i].oe_bit = 9;
-		groups[i].in_bit = 0;
-		groups[i].out_bit = 1;
-		groups[i].intr_enable_bit = 0;
-		groups[i].intr_status_bit = 0;
-		groups[i].intr_target_bit = 5;
-		groups[i].intr_target_kpss_val = 1;
-		groups[i].intr_raw_status_bit = 4;
-		groups[i].intr_polarity_bit = 1;
-		groups[i].intr_detection_bit = 2;
-		groups[i].intr_detection_width = 2;
+	/* Populate the entries that are meant to be exposes as GPIOs. */
+	for (i = 0; i < avail_gpios; i++) {
+		unsigned int gpio = gpios[i];
+
+		groups[gpio].npins = 1;
+		snprintf(names[i], NAME_SIZE, "gpio%u", gpio);
+		pins[gpio].name = names[i];
+		groups[gpio].name = names[i];
+
+		groups[gpio].ctl_reg = 0x10000 * gpio;
+		groups[gpio].io_reg = 0x04 + 0x10000 * gpio;
+		groups[gpio].intr_cfg_reg = 0x08 + 0x10000 * gpio;
+		groups[gpio].intr_status_reg = 0x0c + 0x10000 * gpio;
+		groups[gpio].intr_target_reg = 0x08 + 0x10000 * gpio;
+
+		groups[gpio].mux_bit = 2;
+		groups[gpio].pull_bit = 0;
+		groups[gpio].drv_bit = 6;
+		groups[gpio].oe_bit = 9;
+		groups[gpio].in_bit = 0;
+		groups[gpio].out_bit = 1;
+		groups[gpio].intr_enable_bit = 0;
+		groups[gpio].intr_status_bit = 0;
+		groups[gpio].intr_target_bit = 5;
+		groups[gpio].intr_target_kpss_val = 1;
+		groups[gpio].intr_raw_status_bit = 4;
+		groups[gpio].intr_polarity_bit = 1;
+		groups[gpio].intr_detection_bit = 2;
+		groups[gpio].intr_detection_width = 2;
 	}
 
+	devm_kfree(&pdev->dev, gpios);
+
 	qdf2xxx_pinctrl.pins = pins;
 	qdf2xxx_pinctrl.groups = groups;
 	qdf2xxx_pinctrl.npins = num_gpios;
@@ -109,12 +182,6 @@ static int qdf2xxx_pinctrl_probe(struct platform_device *pdev)
 	return msm_pinctrl_probe(pdev, &qdf2xxx_pinctrl);
 }
 
-static const struct acpi_device_id qdf2xxx_acpi_ids[] = {
-	{"QCOM8001"},
-	{},
-};
-MODULE_DEVICE_TABLE(acpi, qdf2xxx_acpi_ids);
-
 static struct platform_driver qdf2xxx_pinctrl_driver = {
 	.driver = {
 		.name = "qdf2xxx-pinctrl",
-- 
Qualcomm Datacenter Technologies, Inc. as an affiliate of Qualcomm
Technologies, Inc.  Qualcomm Technologies, Inc. is a member of the
Code Aurora Forum, a Linux Foundation Collaborative Project.

[PATCH 3/3] [v2] pinctrl: qcom: qdf2xxx: add support for new ACPI HID QCOM8002

[Timur Tabi]

Newer versions of the firmware for the Qualcomm Datacenter Technologies
QDF2400 restricts access to a subset of the GPIOs on the TLMM.  To
prevent older kernels from accidentally accessing the restricted GPIOs,
we change the ACPI HID for the TLMM block from QCOM8001 to QCOM8002,
and introduce a new property "gpios".  This property is an array of
specific GPIOs that are accessible.  When an older kernel boots on
newer (restricted) firmware, it will fail to probe.

To implement the sparse GPIO map, we register all of the GPIOs, but set
the pin count for the unavailable GPIOs to zero.  The pinctrl-msm
driver will block those unavailable GPIOs from being accessed.

To allow newer kernels to support older firmware, the driver retains
support for QCOM8001.

Signed-off-by: Timur Tabi <timur@codeaurora.org>
---
 drivers/pinctrl/qcom/pinctrl-qdf2xxx.c | 139 ++++++++++++++++++++++++---------
 1 file changed, 103 insertions(+), 36 deletions(-)

diff --git a/drivers/pinctrl/qcom/pinctrl-qdf2xxx.c b/drivers/pinctrl/qcom/pinctrl-qdf2xxx.c
index bb3ce5c..e3b58c4 100644
--- a/drivers/pinctrl/qcom/pinctrl-qdf2xxx.c
+++ b/drivers/pinctrl/qcom/pinctrl-qdf2xxx.c
@@ -38,68 +38,141 @@
 /* maximum size of each gpio name (enough room for "gpioXXX" + null) */
 #define NAME_SIZE	8
 
+enum {
+	QDF2XXX_V1,
+	QDF2XXX_V2,
+};
+
+static const struct acpi_device_id qdf2xxx_acpi_ids[] = {
+	{"QCOM8001", QDF2XXX_V1},
+	{"QCOM8002", QDF2XXX_V2},
+	{},
+};
+MODULE_DEVICE_TABLE(acpi, qdf2xxx_acpi_ids);
+
 static int qdf2xxx_pinctrl_probe(struct platform_device *pdev)
 {
+	const struct acpi_device_id *id =
+		acpi_match_device(qdf2xxx_acpi_ids, &pdev->dev);
 	struct pinctrl_pin_desc *pins;
 	struct msm_pingroup *groups;
 	char (*names)[NAME_SIZE];
 	unsigned int i;
 	u32 num_gpios;
+	unsigned int avail_gpios; /* The number of GPIOs we support */
+	u16 *gpios; /* An array of supported GPIOs */
 	int ret;
 
 	/* Query the number of GPIOs from ACPI */
 	ret = device_property_read_u32(&pdev->dev, "num-gpios", &num_gpios);
 	if (ret < 0) {
-		dev_warn(&pdev->dev, "missing num-gpios property\n");
+		dev_err(&pdev->dev, "missing 'num-gpios' property\n");
 		return ret;
 	}
-
 	if (!num_gpios || num_gpios > MAX_GPIOS) {
-		dev_warn(&pdev->dev, "invalid num-gpios property\n");
+		dev_err(&pdev->dev, "invalid 'num-gpios' property\n");
 		return -ENODEV;
 	}
 
+	/*
+	 * The QCOM8001 HID contains only the number of GPIOs, and assumes
+	 * that all of them are available. avail_gpios is the same as num_gpios.
+	 *
+	 * The QCOM8002 HID introduces the 'gpios' DSD, which lists
+	 * specific GPIOs that the driver is allowed to access.
+	 *
+	 * The make the common code simpler, in both cases we create an
+	 * array of GPIOs that are accessible.  So for QCOM8001, that would
+	 * be all of the GPIOs.
+	 */
+	if (id->driver_data == QDF2XXX_V1) {
+		avail_gpios = num_gpios;
+
+		gpios = devm_kcalloc(&pdev->dev, avail_gpios, sizeof(gpios[0]),
+				     GFP_KERNEL);
+		if (!gpios)
+			return -ENOMEM;
+
+		for (i = 0; i < avail_gpios; i++)
+			gpios[i] = i;
+	} else {
+		/* The number of GPIOs in the approved list */
+		ret = device_property_read_u16_array(&pdev->dev, "gpios",
+						     NULL, 0);
+		if (ret < 0) {
+			dev_err(&pdev->dev, "missing 'num-gpios' property\n");
+			return ret;
+		}
+		if (!ret || ret > MAX_GPIOS) {
+			dev_err(&pdev->dev, "invalid 'num-gpios' property\n");
+			return -ENODEV;
+		}
+		avail_gpios = ret;
+
+		gpios = devm_kcalloc(&pdev->dev, avail_gpios, sizeof(gpios[0]),
+				     GFP_KERNEL);
+		if (!gpios)
+			return -ENOMEM;
+
+		ret = device_property_read_u16_array(&pdev->dev, "gpios", gpios,
+						     avail_gpios);
+		if (ret < 0) {
+			dev_err(&pdev->dev, "could not read list of GPIOs\n");
+			return ret;
+		}
+	}
+
 	pins = devm_kcalloc(&pdev->dev, num_gpios,
 		sizeof(struct pinctrl_pin_desc), GFP_KERNEL);
 	groups = devm_kcalloc(&pdev->dev, num_gpios,
 		sizeof(struct msm_pingroup), GFP_KERNEL);
-	names = devm_kcalloc(&pdev->dev, num_gpios, NAME_SIZE, GFP_KERNEL);
+	names = devm_kcalloc(&pdev->dev, avail_gpios, NAME_SIZE, GFP_KERNEL);
 
 	if (!pins || !groups || !names)
 		return -ENOMEM;
 
+	/*
+	 * Initialize the array.  GPIOs not listed in the 'gpios' array
+	 * still need a number, but nothing else.
+	 */
 	for (i = 0; i < num_gpios; i++) {
-		snprintf(names[i], NAME_SIZE, "gpio%u", i);
-
 		pins[i].number = i;
-		pins[i].name = names[i];
-
-		groups[i].npins = 1;
-		groups[i].name = names[i];
 		groups[i].pins = &pins[i].number;
+	}
 
-		groups[i].ctl_reg = 0x10000 * i;
-		groups[i].io_reg = 0x04 + 0x10000 * i;
-		groups[i].intr_cfg_reg = 0x08 + 0x10000 * i;
-		groups[i].intr_status_reg = 0x0c + 0x10000 * i;
-		groups[i].intr_target_reg = 0x08 + 0x10000 * i;
-
-		groups[i].mux_bit = 2;
-		groups[i].pull_bit = 0;
-		groups[i].drv_bit = 6;
-		groups[i].oe_bit = 9;
-		groups[i].in_bit = 0;
-		groups[i].out_bit = 1;
-		groups[i].intr_enable_bit = 0;
-		groups[i].intr_status_bit = 0;
-		groups[i].intr_target_bit = 5;
-		groups[i].intr_target_kpss_val = 1;
-		groups[i].intr_raw_status_bit = 4;
-		groups[i].intr_polarity_bit = 1;
-		groups[i].intr_detection_bit = 2;
-		groups[i].intr_detection_width = 2;
+	/* Populate the entries that are meant to be exposes as GPIOs. */
+	for (i = 0; i < avail_gpios; i++) {
+		unsigned int gpio = gpios[i];
+
+		groups[gpio].npins = 1;
+		snprintf(names[i], NAME_SIZE, "gpio%u", gpio);
+		pins[gpio].name = names[i];
+		groups[gpio].name = names[i];
+
+		groups[gpio].ctl_reg = 0x10000 * gpio;
+		groups[gpio].io_reg = 0x04 + 0x10000 * gpio;
+		groups[gpio].intr_cfg_reg = 0x08 + 0x10000 * gpio;
+		groups[gpio].intr_status_reg = 0x0c + 0x10000 * gpio;
+		groups[gpio].intr_target_reg = 0x08 + 0x10000 * gpio;
+
+		groups[gpio].mux_bit = 2;
+		groups[gpio].pull_bit = 0;
+		groups[gpio].drv_bit = 6;
+		groups[gpio].oe_bit = 9;
+		groups[gpio].in_bit = 0;
+		groups[gpio].out_bit = 1;
+		groups[gpio].intr_enable_bit = 0;
+		groups[gpio].intr_status_bit = 0;
+		groups[gpio].intr_target_bit = 5;
+		groups[gpio].intr_target_kpss_val = 1;
+		groups[gpio].intr_raw_status_bit = 4;
+		groups[gpio].intr_polarity_bit = 1;
+		groups[gpio].intr_detection_bit = 2;
+		groups[gpio].intr_detection_width = 2;
 	}
 
+	devm_kfree(&pdev->dev, gpios);
+
 	qdf2xxx_pinctrl.pins = pins;
 	qdf2xxx_pinctrl.groups = groups;
 	qdf2xxx_pinctrl.npins = num_gpios;
@@ -109,12 +182,6 @@ static int qdf2xxx_pinctrl_probe(struct platform_device *pdev)
 	return msm_pinctrl_probe(pdev, &qdf2xxx_pinctrl);
 }
 
-static const struct acpi_device_id qdf2xxx_acpi_ids[] = {
-	{"QCOM8001"},
-	{},
-};
-MODULE_DEVICE_TABLE(acpi, qdf2xxx_acpi_ids);
-
 static struct platform_driver qdf2xxx_pinctrl_driver = {
 	.driver = {
 		.name = "qdf2xxx-pinctrl",
-- 
Qualcomm Datacenter Technologies, Inc. as an affiliate of Qualcomm
Technologies, Inc.  Qualcomm Technologies, Inc. is a member of the
Code Aurora Forum, a Linux Foundation Collaborative Project.