From: Rob Herring <robh@kernel.org>
To: "Jonathan Neuschäfer" <j.neuschaefer@gmx.net>
Cc: linux-gpio@vger.kernel.org,
Linus Walleij <linus.walleij@linaro.org>,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
Joel Stanley <joel@jms.id.au>, Tomer Maimon <tmaimon77@gmail.com>,
Rob Herring <robh+dt@kernel.org>,
openbmc@lists.ozlabs.org
Subject: Re: [PATCH v2 4/8] dt-bindings: pinctrl: Add Nuvoton WPCM450
Date: Wed, 08 Dec 2021 07:44:28 -0600 [thread overview]
Message-ID: <1638971068.731875.3857729.nullmailer@robh.at.kernel.org> (raw)
In-Reply-To: <20211207210823.1975632-5-j.neuschaefer@gmx.net>
[-- Warning: decoded text below may be mangled, UTF-8 assumed --]
[-- Attachment #1: Type: text/plain, Size: 3143 bytes --]
On Tue, 07 Dec 2021 22:08:19 +0100, Jonathan Neuschäfer wrote:
> This binding is heavily based on the one for NPCM7xx, because the
> hardware is similar. There are some notable differences, however:
>
> - The addresses of GPIO banks are not physical addresses but simple
> indices (0 to 7), because the GPIO registers are not laid out in
> convenient blocks.
> - Pinmux settings can explicitly specify that the GPIO mode is used.
>
> Certain pins support blink patterns in hardware. This is currently not
> modelled in the DT binding.
>
> Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
>
>
> ---
> v2:
> - Move GPIO into subnodes
> - Improve use of quotes
> - Remove unnecessary minItems/maxItems lines
> - Remove "phandle: true"
> - Use separate prefixes for pinmux and pincfg nodes
> - Add nuvoton,interrupt-map property
> - Make it possible to set pinmux to GPIO explicitly
>
> v1:
> - https://lore.kernel.org/lkml/20210602120329.2444672-5-j.neuschaefer@gmx.net/
> ---
> .../pinctrl/nuvoton,wpcm450-pinctrl.yaml | 190 ++++++++++++++++++
> 1 file changed, 190 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pinctrl/nuvoton,wpcm450-pinctrl.yaml
>
My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):
yamllint warnings/errors:
dtschema/dtc warnings/errors:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/pinctrl/nuvoton,wpcm450-pinctrl.example.dt.yaml: pinctrl@b8003000: gpio@0:interrupts: [[2, 4, 3, 4, 4, 4]] is too short
From schema: /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/pinctrl/nuvoton,wpcm450-pinctrl.yaml
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/pinctrl/nuvoton,wpcm450-pinctrl.example.dt.yaml: pinctrl@b8003000: mux_uid: Additional properties are not allowed ('phandle' was unexpected)
From schema: /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/pinctrl/nuvoton,wpcm450-pinctrl.yaml
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/pinctrl/nuvoton,wpcm450-pinctrl.example.dt.yaml: pinctrl@b8003000: cfg_uid: Additional properties are not allowed ('phandle' was unexpected)
From schema: /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/pinctrl/nuvoton,wpcm450-pinctrl.yaml
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/pinctrl/nuvoton,wpcm450-pinctrl.example.dt.yaml: pinctrl@b8003000: '#address-cells', '#size-cells' do not match any of the regexes: '^cfg_.*$', '^gpio@.*$', '^mux_.*$', 'pinctrl-[0-9]+'
From schema: /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/pinctrl/nuvoton,wpcm450-pinctrl.yaml
doc reference errors (make refcheckdocs):
See https://patchwork.ozlabs.org/patch/1564902
This check can fail if there are any dependencies. The base for a patch
series is generally the most recent rc1.
If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:
pip3 install dtschema --upgrade
Please check and re-submit.
next prev parent reply other threads:[~2021-12-08 13:44 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-12-07 21:08 [PATCH v2 0/8] Nuvoton WPCM450 pinctrl and GPIO driver Jonathan Neuschäfer
2021-12-07 21:08 ` [PATCH v2 1/8] dt-bindings: arm/npcm: Add binding for global control registers (GCR) Jonathan Neuschäfer
2021-12-08 13:44 ` Rob Herring
2021-12-10 14:54 ` Rob Herring
2021-12-12 23:12 ` Jonathan Neuschäfer
2021-12-07 21:08 ` [PATCH v2 2/8] MAINTAINERS: Match all of bindings/arm/npcm/ as part of NPCM architecture Jonathan Neuschäfer
2021-12-07 21:08 ` [PATCH v2 3/8] ARM: dts: wpcm450: Add global control registers (GCR) node Jonathan Neuschäfer
2021-12-07 21:08 ` [PATCH v2 4/8] dt-bindings: pinctrl: Add Nuvoton WPCM450 Jonathan Neuschäfer
2021-12-08 13:44 ` Rob Herring [this message]
2021-12-10 15:18 ` Rob Herring
2021-12-12 23:38 ` Jonathan Neuschäfer
2021-12-07 21:08 ` [PATCH v2 5/8] pinctrl: nuvoton: Add driver for WPCM450 Jonathan Neuschäfer
2021-12-08 0:51 ` kernel test robot
2021-12-08 2:34 ` kernel test robot
[not found] ` <CAHp75Vew=M_ofNM5pmeHtTJHXRUbbO4RrtgYAtLBznTBm3CS6Q@mail.gmail.com>
2021-12-08 13:58 ` Jonathan Neuschäfer
2021-12-08 14:14 ` Andy Shevchenko
2021-12-12 23:02 ` Jonathan Neuschäfer
2021-12-09 8:26 ` Zev Weiss
2021-12-10 1:41 ` Linus Walleij
2021-12-12 23:03 ` Jonathan Neuschäfer
2021-12-07 21:08 ` [PATCH v2 6/8] ARM: dts: wpcm450: Add pinctrl and GPIO nodes Jonathan Neuschäfer
2021-12-10 1:42 ` Linus Walleij
2021-12-07 21:08 ` [PATCH v2 7/8] ARM: dts: wpcm450: Add pin functions Jonathan Neuschäfer
2021-12-07 21:08 ` [PATCH v2 8/8] ARM: dts: wpcm450-supermicro-x9sci-ln4f: Add GPIO LEDs and buttons Jonathan Neuschäfer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1638971068.731875.3857729.nullmailer@robh.at.kernel.org \
--to=robh@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=j.neuschaefer@gmx.net \
--cc=joel@jms.id.au \
--cc=linus.walleij@linaro.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=openbmc@lists.ozlabs.org \
--cc=robh+dt@kernel.org \
--cc=tmaimon77@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).