[PATCH RFC 00/14] Add MSM8917/PM8937/Redmi 5A

[PATCH RFC 00/14] Add MSM8917/PM8937/Redmi 5A

[Barnabás Czémán]

This patch series add support for MSM8917 soc with PM8937 and
Xiaomi Redmi 5A (riva).

Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
---
Barnabás Czémán (11):
      dt-bindings: pinctrl: qcom,pmic-gpio: add PM8937
      pinctrl: qcom-pmic-gpio: add support for PM8937
      dt-bindings: pinctrl: qcom,pmic-mpp: Document PM8937 compatible
      pinctrl: qcom: spmi-mpp: Add PM8937 compatible
      dt-bindings: pinctrl: qcom: Add MSM8917 pinctrl bindings
      dt-bindings: mfd: qcom,tcsr: Add compatible for MSM8917
      dt-bindings: thermal: tsens: Add MSM8917 compatible
      dt-bindings: iommu: qcom,iommu: Add MSM8917 IOMMU to SMMUv1 compatibles
      dt-bindings: nvmem: Add compatible for MS8917
      dt-bindings: arm: qcom: Add Xiaomi Redmi 5A
      arm64: dts: qcom: Add Xiaomi Redmi 5A

Dang Huynh (1):
      arm64: dts: qcom: Add PM8937 PMIC

Otto Pflüger (2):
      pinctrl: qcom: Add MSM8917 tlmm pinctrl driver
      arm64: dts: qcom: Add initial support for MSM8917

 Documentation/devicetree/bindings/arm/qcom.yaml    |    7 +
 .../devicetree/bindings/iommu/qcom,iommu.yaml      |    1 +
 .../devicetree/bindings/mfd/qcom,tcsr.yaml         |    1 +
 .../devicetree/bindings/nvmem/qcom,qfprom.yaml     |    1 +
 .../bindings/pinctrl/qcom,msm8917-pinctrl.yaml     |  155 ++
 .../bindings/pinctrl/qcom,pmic-gpio.yaml           |    3 +
 .../devicetree/bindings/pinctrl/qcom,pmic-mpp.yaml |    2 +
 .../devicetree/bindings/thermal/qcom-tsens.yaml    |    1 +
 arch/arm64/boot/dts/qcom/Makefile                  |    1 +
 arch/arm64/boot/dts/qcom/msm8917-pins.dtsi         |  344 +++++
 arch/arm64/boot/dts/qcom/msm8917-xiaomi-riva.dts   |  295 ++++
 arch/arm64/boot/dts/qcom/msm8917.dtsi              | 1557 +++++++++++++++++++
 arch/arm64/boot/dts/qcom/pm8916.dtsi               |    9 +-
 arch/arm64/boot/dts/qcom/pm8937.dtsi               |  216 +++
 drivers/pinctrl/qcom/Kconfig.msm                   |    6 +
 drivers/pinctrl/qcom/Makefile                      |    1 +
 drivers/pinctrl/qcom/pinctrl-msm8917.c             | 1622 ++++++++++++++++++++
 drivers/pinctrl/qcom/pinctrl-spmi-gpio.c           |    2 +
 drivers/pinctrl/qcom/pinctrl-spmi-mpp.c            |    1 +
 19 files changed, 4224 insertions(+), 1 deletion(-)
---
base-commit: f2493655d2d3d5c6958ed996b043c821c23ae8d3
change-id: 20241019-msm8917-17c3d0ff4a52

Best regards,
-- 
Barnabás Czémán <barnabas.czeman@mainlining.org>

[PATCH RFC 01/14] dt-bindings: pinctrl: qcom,pmic-gpio: add PM8937

[Barnabás Czémán]

Document the 8 GPIOs found on PM8937. It has holes on
3,4 and 6 pins.

Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
---
 Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.yaml | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.yaml
index c1b799167d81b0b4e1edff6a6fce557fa88fd1ea..055cea5452eb62ab6e251a3a9193d1e5da293ccb 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.yaml
@@ -48,6 +48,7 @@ properties:
           - qcom,pm8916-gpio
           - qcom,pm8917-gpio
           - qcom,pm8921-gpio
+          - qcom,pm8937-gpio
           - qcom,pm8941-gpio
           - qcom,pm8950-gpio
           - qcom,pm8953-gpio
@@ -184,6 +185,7 @@ allOf:
               - qcom,pm8226-gpio
               - qcom,pm8350b-gpio
               - qcom,pm8550ve-gpio
+              - qcom,pm8937-gpio
               - qcom,pm8950-gpio
               - qcom,pm8953-gpio
               - qcom,pmi632-gpio
@@ -468,6 +470,7 @@ $defs:
                  - gpio1-gpio6 for pm8550vs
                  - gpio1-gpio38 for pm8917
                  - gpio1-gpio44 for pm8921
+                 - gpio1-gpio8 for pm8937 (hole on gpio3, gpio4 and gpio6)
                  - gpio1-gpio36 for pm8941
                  - gpio1-gpio8 for pm8950 (hole on gpio3)
                  - gpio1-gpio8 for pm8953 (hole on gpio3 and gpio6)

-- 
2.47.0

[PATCH RFC 02/14] pinctrl: qcom-pmic-gpio: add support for PM8937

[Barnabás Czémán]

PM8937 has 8 GPIO-s with holes on GPIO3, GPIO4 and GPIO6.

Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
---
 drivers/pinctrl/qcom/pinctrl-spmi-gpio.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c b/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
index c33af2d6677846a4c43fc817e7b01621ab220890..b1140eaecd32de90e4ae2eafb1d0e0ec939e24bf 100644
--- a/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
+++ b/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
@@ -1226,6 +1226,8 @@ static const struct of_device_id pmic_gpio_of_match[] = {
 	{ .compatible = "qcom,pm8550ve-gpio", .data = (void *) 8 },
 	{ .compatible = "qcom,pm8550vs-gpio", .data = (void *) 6 },
 	{ .compatible = "qcom,pm8916-gpio", .data = (void *) 4 },
+	/* pm8937 has 8 GPIOs with holes on 3, 4 and 6 */
+	{ .compatible = "qcom,pm8937-gpio", .data = (void *) 8 },
 	{ .compatible = "qcom,pm8941-gpio", .data = (void *) 36 },
 	/* pm8950 has 8 GPIOs with holes on 3 */
 	{ .compatible = "qcom,pm8950-gpio", .data = (void *) 8 },

-- 
2.47.0

[PATCH RFC 03/14] dt-bindings: pinctrl: qcom,pmic-mpp: Document PM8937 compatible

[Barnabás Czémán]

Document the Device Tree binding for PM8937 MPPs.

Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
---
 Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.yaml
index 43146709e2044d9dead08a6786b98672ef766629..9364ae05f3e68f3a2f4dd78ba3c0f94b3ccc3c51 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.yaml
@@ -22,6 +22,7 @@ properties:
               - qcom,pm8226-mpp
               - qcom,pm8841-mpp
               - qcom,pm8916-mpp
+              - qcom,pm8937-mpp
               - qcom,pm8941-mpp
               - qcom,pm8950-mpp
               - qcom,pmi8950-mpp
@@ -92,6 +93,7 @@ $defs:
           this subnode.  Valid pins are
                  - mpp1-mpp4 for pm8841
                  - mpp1-mpp4 for pm8916
+                 - mpp1-mpp4 for pm8937
                  - mpp1-mpp8 for pm8941
                  - mpp1-mpp4 for pm8950
                  - mpp1-mpp4 for pmi8950

-- 
2.47.0

[PATCH RFC 04/14] pinctrl: qcom: spmi-mpp: Add PM8937 compatible

[Barnabás Czémán]

The PM8937 provides 4 MPPs.
Add a compatible to support them.

Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
---
 drivers/pinctrl/qcom/pinctrl-spmi-mpp.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/pinctrl/qcom/pinctrl-spmi-mpp.c b/drivers/pinctrl/qcom/pinctrl-spmi-mpp.c
index b5b3ac82f030b55f9e199bb4265c770cfde4a81a..84de584cf7ebbd35dd3e7aa89d4b971645b02f82 100644
--- a/drivers/pinctrl/qcom/pinctrl-spmi-mpp.c
+++ b/drivers/pinctrl/qcom/pinctrl-spmi-mpp.c
@@ -983,6 +983,7 @@ static const struct of_device_id pmic_mpp_of_match[] = {
 	{ .compatible = "qcom,pm8226-mpp", .data = (void *) 8 },
 	{ .compatible = "qcom,pm8841-mpp", .data = (void *) 4 },
 	{ .compatible = "qcom,pm8916-mpp", .data = (void *) 4 },
+	{ .compatible = "qcom,pm8937-mpp", .data = (void *) 4 },
 	{ .compatible = "qcom,pm8941-mpp", .data = (void *) 8 },
 	{ .compatible = "qcom,pm8950-mpp", .data = (void *) 4 },
 	{ .compatible = "qcom,pmi8950-mpp", .data = (void *) 4 },

-- 
2.47.0

[PATCH RFC 05/14] arm64: dts: qcom: Add PM8937 PMIC

[Barnabás Czémán]

From: Dang Huynh <danct12@riseup.net>

The PM8937 features integrated peripherals like ADC, GPIO controller,
MPPs, PON keys and others.

Add the device tree so that any boards with this PMIC can use it.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Dang Huynh <danct12@riseup.net>
Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
---
 arch/arm64/boot/dts/qcom/pm8937.dtsi | 216 +++++++++++++++++++++++++++++++++++
 1 file changed, 216 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/pm8937.dtsi b/arch/arm64/boot/dts/qcom/pm8937.dtsi
new file mode 100644
index 0000000000000000000000000000000000000000..34e2b4cd0d5f4f92c16bb20f53e4520544a644bc
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pm8937.dtsi
@@ -0,0 +1,216 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023, Dang Huynh <danct12@riseup.net>
+ */
+
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+	thermal-zones {
+		pm8937-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&pm8937_temp>;
+
+			trips {
+				trip0 {
+					temperature = <105000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <125000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+
+				trip2 {
+					temperature = <145000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
+&spmi_bus {
+	pmic@0 {
+		compatible = "qcom,pm8937", "qcom,spmi-pmic";
+		reg = <0x0 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pon@800 {
+			compatible = "qcom,pm8916-pon";
+			reg = <0x800>;
+			mode-bootloader = <0x2>;
+			mode-recovery = <0x1>;
+
+			pm8937_pwrkey: pwrkey {
+				compatible = "qcom,pm8941-pwrkey";
+				interrupts = <0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+				linux,code = <KEY_POWER>;
+			};
+
+			pm8937_resin: resin {
+				compatible = "qcom,pm8941-resin";
+				interrupts = <0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+				status = "disabled";
+			};
+		};
+
+		pm8937_gpios: gpio@c000 {
+			compatible = "qcom,pm8937-gpio", "qcom,spmi-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			gpio-ranges = <&pm8937_gpios 0 0 8>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		pm8937_mpps: mpps@a000 {
+			compatible = "qcom,pm8937-mpp", "qcom,spmi-mpp";
+			reg = <0xa000>;
+			gpio-controller;
+			gpio-ranges = <&pm8937_mpps 0 0 4>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		pm8937_temp: temp-alarm@2400 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0x2400>;
+			interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
+			io-channels = <&pm8937_vadc VADC_DIE_TEMP>;
+			io-channel-names = "thermal";
+			#thermal-sensor-cells = <0>;
+		};
+
+		pm8937_vadc: adc@3100 {
+			compatible = "qcom,spmi-vadc";
+			reg = <0x3100>;
+			interrupts = <0 0x31 0 IRQ_TYPE_EDGE_RISING>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#io-channel-cells = <1>;
+
+			channel@5 {
+				reg = <VADC_VCOIN>;
+				qcom,pre-scaling = <1 1>;
+				label = "vcoin";
+			};
+
+			channel@7 {
+				reg = <VADC_VSYS>;
+				qcom,pre-scaling = <1 1>;
+				label = "vph_pwr";
+			};
+
+			channel@8 {
+				reg = <VADC_DIE_TEMP>;
+				qcom,pre-scaling = <1 1>;
+				label = "die_temp";
+			};
+
+			channel@9 {
+				reg = <VADC_REF_625MV>;
+				qcom,pre-scaling = <1 1>;
+				label = "ref_625mv";
+			};
+
+			channel@a {
+				reg = <VADC_REF_1250MV>;
+				qcom,pre-scaling = <1 1>;
+				label = "ref_1250mv";
+			};
+
+			channel@c {
+				reg = <VADC_SPARE1>;
+				qcom,pre-scaling = <1 1>;
+				label = "ref_buf_625mv";
+			};
+
+			channel@e {
+				reg = <VADC_GND_REF>;
+				qcom,pre-scaling = <1 1>;
+				label = "ref_gnd";
+			};
+
+			channel@f {
+				reg = <VADC_VDD_VADC>;
+				qcom,pre-scaling = <1 1>;
+				label = "ref_vdd";
+			};
+
+			channel@11 {
+				reg = <VADC_P_MUX2_1_1>;
+				qcom,pre-scaling = <1 1>;
+				qcom,ratiometric;
+				qcom,hw-settle-time = <200>;
+				label = "pa_therm1";
+			};
+
+			channel@13 {
+				reg = <VADC_P_MUX4_1_1>;
+				qcom,pre-scaling = <1 1>;
+				qcom,ratiometric;
+				qcom,hw-settle-time = <200>;
+				label = "case_therm";
+			};
+
+			channel@32 {
+				reg = <VADC_LR_MUX3_XO_THERM>;
+				qcom,pre-scaling = <1 1>;
+				qcom,ratiometric;
+				qcom,hw-settle-time = <200>;
+				label = "xo_therm";
+			};
+
+			channel@36 {
+				reg = <VADC_LR_MUX7_HW_ID>;
+				qcom,pre-scaling = <1 1>;
+				qcom,ratiometric;
+				qcom,hw-settle-time = <200>;
+				label = "pa_therm0";
+			};
+
+			channel@3c {
+				reg = <VADC_LR_MUX3_BUF_XO_THERM>;
+				qcom,pre-scaling = <1 1>;
+				qcom,ratiometric;
+				qcom,hw-settle-time = <200>;
+				label = "xo_therm_buf";
+			};
+		};
+
+		rtc@6000 {
+			compatible = "qcom,pm8941-rtc";
+			reg = <0x6000>, <0x6100>;
+			reg-names = "rtc", "alarm";
+			interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
+		};
+	};
+
+	pmic@1 {
+		compatible = "qcom,pm8937", "qcom,spmi-pmic";
+		reg = <0x1 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8937_spmi_regulators: regulators {
+			compatible = "qcom,pm8937-regulators";
+		};
+	};
+};

-- 
2.47.0

[PATCH RFC 06/14] dt-bindings: pinctrl: qcom: Add MSM8917 pinctrl bindings

[Barnabás Czémán]

Add device tree bindings documentation for Qualcomm MSM8917
pinctrl driver.

Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
---
 .../bindings/pinctrl/qcom,msm8917-pinctrl.yaml     | 155 +++++++++++++++++++++
 1 file changed, 155 insertions(+)

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8917-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,msm8917-pinctrl.yaml
new file mode 100644
index 0000000000000000000000000000000000000000..41349ce9898aaaf68a10f30ffe611dcedc1e9311
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8917-pinctrl.yaml
@@ -0,0 +1,155 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/qcom,msm8917-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm MSM8917 TLMM pin controller
+
+maintainers:
+  - Barnabas Czeman <barnabas.czeman@mainlining.org>
+
+description:
+  Top Level Mode Multiplexer pin controller in Qualcomm MSM8917 SoC.
+
+properties:
+  compatible:
+    const: qcom,msm8917-pinctrl
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  gpio-reserved-ranges: true
+
+patternProperties:
+  "-state$":
+    oneOf:
+      - $ref: "#/$defs/qcom-msm8917-tlmm-state"
+      - patternProperties:
+          "-pins$":
+            $ref: "#/$defs/qcom-msm8917-tlmm-state"
+        additionalProperties: false
+
+$defs:
+  qcom-msm8917-tlmm-state:
+    type: object
+    description:
+      Pinctrl node's client devices use subnodes for desired pin configuration.
+      Client device subnodes use below standard properties.
+    $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
+    unevaluatedProperties: false
+
+    properties:
+      pins:
+        description:
+          List of gpio pins affected by the properties specified in this
+          subnode.
+        items:
+          oneOf:
+            - pattern: "^gpio([0-9]|[1-9][0-9]|1[0-3][0-9]|14[01])$"
+            - enum: [ sdc1_clk, sdc1_cmd, sdc1_data, sdc1_rclk, sdc2_clk,
+                      sdc2_cmd, sdc2_data, qdsd_clk, qdsd_cmd, qdsd_data0,
+                      qdsd_data1, qdsd_data2, qdsd_data3 ]
+        minItems: 1
+        maxItems: 16
+
+      function:
+        description:
+          Specify the alternative function to be configured for the specified
+          pins.
+
+        enum: [ accel_int, adsp_ext, alsp_int, atest_bbrx0, atest_bbrx1,
+                atest_char, atest_char0, atest_char1, atest_char2,
+                atest_char3, atest_combodac_to_gpio_native,
+                atest_gpsadc_dtest0_native, atest_gpsadc_dtest1_native,
+                atest_tsens, atest_wlan0, atest_wlan1, audio_ref,
+                audio_reset, bimc_dte0, bimc_dte1, blsp6_spi, blsp8_spi,
+                blsp_i2c1, blsp_i2c2, blsp_i2c3, blsp_i2c4, blsp_i2c5,
+                blsp_i2c6, blsp_i2c7, blsp_i2c8, blsp_spi1, blsp_spi2,
+                blsp_spi3, blsp_spi4, blsp_spi5, blsp_spi6, blsp_spi7,
+                blsp_spi8, blsp_uart1, blsp_uart2, blsp_uart3, blsp_uart4,
+                blsp_uart5, blsp_uart6, blsp_uart7, blsp_uart8, cam0_ldo,
+                cam1_rst, cam1_standby, cam2_rst, cam2_standby, cam_mclk,
+                cci_async, cci_i2c, cci_timer0, cci_timer1, cdc_pdm0,
+                codec_int1, codec_int2, codec_mad, coex_uart, cri_trng,
+                cri_trng0, cri_trng1, dbg_out, dmic0_clk, dmic0_data,
+                ebi_cdc, ebi_ch0, ext_lpass, forced_usb, fp_gpio, fp_int,
+                gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a, gcc_gp2_clk_b,
+                gcc_gp3_clk_a, gcc_gp3_clk_b, gcc_plltest, gcc_tlmm, gpio,
+                gsm0_tx, key_focus, key_snapshot, key_volp, ldo_en,
+                ldo_update, lpass_slimbus, lpass_slimbus0, lpass_slimbus1,
+                m_voc, mag_int, mdp_vsync, mipi_dsi0, modem_tsync, nav_pps,
+                nav_pps_in_a, nav_pps_in_b, nav_tsync, nfc_pwr, ov_ldo,
+                pa_indicator, pbs0, pbs1, pbs2, pri_mi2s, pri_mi2s_mclk_a,
+                pri_mi2s_mclk_b, pri_mi2s_ws, prng_rosc,
+                pwr_crypto_enabled_a, pwr_crypto_enabled_b,
+                pwr_modem_enabled_a, pwr_modem_enabled_b, pwr_nav_enabled_a,
+                pwr_nav_enabled_b, qdss_cti_trig_in_a0, qdss_cti_trig_in_a1,
+                qdss_cti_trig_in_b0, qdss_cti_trig_in_b1,
+                qdss_cti_trig_out_a0, qdss_cti_trig_out_a1,
+                qdss_cti_trig_out_b0, qdss_cti_trig_out_b1, qdss_traceclk_a,
+                qdss_traceclk_b, qdss_tracectl_a, qdss_tracectl_b,
+                qdss_tracedata_a, qdss_tracedata_b, sd_write, sdcard_det,
+                sec_mi2s, sec_mi2s_mclk_a, sec_mi2s_mclk_b, sensor_rst,
+                smb_int, ssbi_wtr1, ts_resout, ts_sample, uim1_clk,
+                uim1_data, uim1_present, uim1_reset, uim2_clk, uim2_data,
+                uim2_present, uim2_reset, uim_batt, us_emitter, us_euro,
+                wcss_bt, wcss_fm, wcss_wlan, wcss_wlan0, wcss_wlan1,
+                wcss_wlan2, webcam_rst, webcam_standby, wsa_io, wsa_irq ]
+
+    required:
+      - pins
+
+allOf:
+  - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
+
+required:
+  - compatible
+  - reg
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    tlmm: pinctrl@1000000 {
+        compatible = "qcom,msm8917-pinctrl";
+        reg = <0x01000000 0x300000>;
+        interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+        gpio-controller;
+        gpio-ranges = <&tlmm 0 0 134>;
+        #gpio-cells = <2>;
+        interrupt-controller;
+        #interrupt-cells = <2>;
+
+        blsp1-uart2-sleep-state {
+            pins = "gpio4", "gpio5";
+            function = "gpio";
+
+            drive-strength = <2>;
+            bias-pull-down;
+        };
+
+        spi1-default-state {
+            spi-pins {
+                pins = "gpio0", "gpio1", "gpio3";
+                function = "blsp_spi1";
+
+                drive-strength = <12>;
+                bias-disable;
+            };
+
+            cs-pins {
+                pins = "gpio2";
+                function = "gpio";
+
+                drive-strength = <16>;
+                bias-disable;
+                output-high;
+            };
+        };
+    };

-- 
2.47.0

[PATCH RFC 07/14] pinctrl: qcom: Add MSM8917 tlmm pinctrl driver

[Barnabás Czémán]

From: Otto Pflüger <otto.pflueger@abscue.de>

It is based on MSM8916 driver with the pinctrl definitions from
Qualcomm's downstream MSM8917 driver.

Signed-off-by: Otto Pflüger <otto.pflueger@abscue.de>
Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
---
 drivers/pinctrl/qcom/Kconfig.msm       |    6 +
 drivers/pinctrl/qcom/Makefile          |    1 +
 drivers/pinctrl/qcom/pinctrl-msm8917.c | 1622 ++++++++++++++++++++++++++++++++
 3 files changed, 1629 insertions(+)

diff --git a/drivers/pinctrl/qcom/Kconfig.msm b/drivers/pinctrl/qcom/Kconfig.msm
index c79f0c3c873da56e8c0e1de9f91bce4b552221d2..f53043ea213012447aaaf07e9f339a16493a1b95 100644
--- a/drivers/pinctrl/qcom/Kconfig.msm
+++ b/drivers/pinctrl/qcom/Kconfig.msm
@@ -137,6 +137,12 @@ config PINCTRL_MSM8916
 	  This is the pinctrl, pinmux, pinconf and gpiolib driver for the
 	  Qualcomm TLMM block found on the Qualcomm 8916 platform.
 
+config PINCTRL_MSM8917
+	tristate "Qualcomm 8917 pin controller driver"
+	help
+	  This is the pinctrl, pinmux, pinconf and gpiolib driver for the
+	  Qualcomm TLMM block found on the Qualcomm 8917 platform.
+
 config PINCTRL_MSM8953
 	tristate "Qualcomm 8953 pin controller driver"
 	depends on ARM64 || COMPILE_TEST
diff --git a/drivers/pinctrl/qcom/Makefile b/drivers/pinctrl/qcom/Makefile
index 715c3b5a636ad6a1b07b4160f4336b5c70a8f2e3..268264ea87aa9dd37d27ca7944e0bf4e674e8132 100644
--- a/drivers/pinctrl/qcom/Makefile
+++ b/drivers/pinctrl/qcom/Makefile
@@ -17,6 +17,7 @@ obj-$(CONFIG_PINCTRL_MSM8960)	+= pinctrl-msm8960.o
 obj-$(CONFIG_PINCTRL_MSM8X74)	+= pinctrl-msm8x74.o
 obj-$(CONFIG_PINCTRL_MSM8909)	+= pinctrl-msm8909.o
 obj-$(CONFIG_PINCTRL_MSM8916)	+= pinctrl-msm8916.o
+obj-$(CONFIG_PINCTRL_MSM8917)	+= pinctrl-msm8917.o
 obj-$(CONFIG_PINCTRL_MSM8953)	+= pinctrl-msm8953.o
 obj-$(CONFIG_PINCTRL_MSM8976)	+= pinctrl-msm8976.o
 obj-$(CONFIG_PINCTRL_MSM8994)   += pinctrl-msm8994.o
diff --git a/drivers/pinctrl/qcom/pinctrl-msm8917.c b/drivers/pinctrl/qcom/pinctrl-msm8917.c
new file mode 100644
index 0000000000000000000000000000000000000000..101baf6d7f8e446bd9045487eea8c810dbc0db5a
--- /dev/null
+++ b/drivers/pinctrl/qcom/pinctrl-msm8917.c
@@ -0,0 +1,1622 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2024, The Linux Foundation. All rights reserved.
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+
+#include "pinctrl-msm.h"
+
+static const struct pinctrl_pin_desc msm8917_pins[] = {
+	PINCTRL_PIN(0, "GPIO_0"),
+	PINCTRL_PIN(1, "GPIO_1"),
+	PINCTRL_PIN(2, "GPIO_2"),
+	PINCTRL_PIN(3, "GPIO_3"),
+	PINCTRL_PIN(4, "GPIO_4"),
+	PINCTRL_PIN(5, "GPIO_5"),
+	PINCTRL_PIN(6, "GPIO_6"),
+	PINCTRL_PIN(7, "GPIO_7"),
+	PINCTRL_PIN(8, "GPIO_8"),
+	PINCTRL_PIN(9, "GPIO_9"),
+	PINCTRL_PIN(10, "GPIO_10"),
+	PINCTRL_PIN(11, "GPIO_11"),
+	PINCTRL_PIN(12, "GPIO_12"),
+	PINCTRL_PIN(13, "GPIO_13"),
+	PINCTRL_PIN(14, "GPIO_14"),
+	PINCTRL_PIN(15, "GPIO_15"),
+	PINCTRL_PIN(16, "GPIO_16"),
+	PINCTRL_PIN(17, "GPIO_17"),
+	PINCTRL_PIN(18, "GPIO_18"),
+	PINCTRL_PIN(19, "GPIO_19"),
+	PINCTRL_PIN(20, "GPIO_20"),
+	PINCTRL_PIN(21, "GPIO_21"),
+	PINCTRL_PIN(22, "GPIO_22"),
+	PINCTRL_PIN(23, "GPIO_23"),
+	PINCTRL_PIN(24, "GPIO_24"),
+	PINCTRL_PIN(25, "GPIO_25"),
+	PINCTRL_PIN(26, "GPIO_26"),
+	PINCTRL_PIN(27, "GPIO_27"),
+	PINCTRL_PIN(28, "GPIO_28"),
+	PINCTRL_PIN(29, "GPIO_29"),
+	PINCTRL_PIN(30, "GPIO_30"),
+	PINCTRL_PIN(31, "GPIO_31"),
+	PINCTRL_PIN(32, "GPIO_32"),
+	PINCTRL_PIN(33, "GPIO_33"),
+	PINCTRL_PIN(34, "GPIO_34"),
+	PINCTRL_PIN(35, "GPIO_35"),
+	PINCTRL_PIN(36, "GPIO_36"),
+	PINCTRL_PIN(37, "GPIO_37"),
+	PINCTRL_PIN(38, "GPIO_38"),
+	PINCTRL_PIN(39, "GPIO_39"),
+	PINCTRL_PIN(40, "GPIO_40"),
+	PINCTRL_PIN(41, "GPIO_41"),
+	PINCTRL_PIN(42, "GPIO_42"),
+	PINCTRL_PIN(43, "GPIO_43"),
+	PINCTRL_PIN(44, "GPIO_44"),
+	PINCTRL_PIN(45, "GPIO_45"),
+	PINCTRL_PIN(46, "GPIO_46"),
+	PINCTRL_PIN(47, "GPIO_47"),
+	PINCTRL_PIN(48, "GPIO_48"),
+	PINCTRL_PIN(49, "GPIO_49"),
+	PINCTRL_PIN(50, "GPIO_50"),
+	PINCTRL_PIN(51, "GPIO_51"),
+	PINCTRL_PIN(52, "GPIO_52"),
+	PINCTRL_PIN(53, "GPIO_53"),
+	PINCTRL_PIN(54, "GPIO_54"),
+	PINCTRL_PIN(55, "GPIO_55"),
+	PINCTRL_PIN(56, "GPIO_56"),
+	PINCTRL_PIN(57, "GPIO_57"),
+	PINCTRL_PIN(58, "GPIO_58"),
+	PINCTRL_PIN(59, "GPIO_59"),
+	PINCTRL_PIN(60, "GPIO_60"),
+	PINCTRL_PIN(61, "GPIO_61"),
+	PINCTRL_PIN(62, "GPIO_62"),
+	PINCTRL_PIN(63, "GPIO_63"),
+	PINCTRL_PIN(64, "GPIO_64"),
+	PINCTRL_PIN(65, "GPIO_65"),
+	PINCTRL_PIN(66, "GPIO_66"),
+	PINCTRL_PIN(67, "GPIO_67"),
+	PINCTRL_PIN(68, "GPIO_68"),
+	PINCTRL_PIN(69, "GPIO_69"),
+	PINCTRL_PIN(70, "GPIO_70"),
+	PINCTRL_PIN(71, "GPIO_71"),
+	PINCTRL_PIN(72, "GPIO_72"),
+	PINCTRL_PIN(73, "GPIO_73"),
+	PINCTRL_PIN(74, "GPIO_74"),
+	PINCTRL_PIN(75, "GPIO_75"),
+	PINCTRL_PIN(76, "GPIO_76"),
+	PINCTRL_PIN(77, "GPIO_77"),
+	PINCTRL_PIN(78, "GPIO_78"),
+	PINCTRL_PIN(79, "GPIO_79"),
+	PINCTRL_PIN(80, "GPIO_80"),
+	PINCTRL_PIN(81, "GPIO_81"),
+	PINCTRL_PIN(82, "GPIO_82"),
+	PINCTRL_PIN(83, "GPIO_83"),
+	PINCTRL_PIN(84, "GPIO_84"),
+	PINCTRL_PIN(85, "GPIO_85"),
+	PINCTRL_PIN(86, "GPIO_86"),
+	PINCTRL_PIN(87, "GPIO_87"),
+	PINCTRL_PIN(88, "GPIO_88"),
+	PINCTRL_PIN(89, "GPIO_89"),
+	PINCTRL_PIN(90, "GPIO_90"),
+	PINCTRL_PIN(91, "GPIO_91"),
+	PINCTRL_PIN(92, "GPIO_92"),
+	PINCTRL_PIN(93, "GPIO_93"),
+	PINCTRL_PIN(94, "GPIO_94"),
+	PINCTRL_PIN(95, "GPIO_95"),
+	PINCTRL_PIN(96, "GPIO_96"),
+	PINCTRL_PIN(97, "GPIO_97"),
+	PINCTRL_PIN(98, "GPIO_98"),
+	PINCTRL_PIN(99, "GPIO_99"),
+	PINCTRL_PIN(100, "GPIO_100"),
+	PINCTRL_PIN(101, "GPIO_101"),
+	PINCTRL_PIN(102, "GPIO_102"),
+	PINCTRL_PIN(103, "GPIO_103"),
+	PINCTRL_PIN(104, "GPIO_104"),
+	PINCTRL_PIN(105, "GPIO_105"),
+	PINCTRL_PIN(106, "GPIO_106"),
+	PINCTRL_PIN(107, "GPIO_107"),
+	PINCTRL_PIN(108, "GPIO_108"),
+	PINCTRL_PIN(109, "GPIO_109"),
+	PINCTRL_PIN(110, "GPIO_110"),
+	PINCTRL_PIN(111, "GPIO_111"),
+	PINCTRL_PIN(112, "GPIO_112"),
+	PINCTRL_PIN(113, "GPIO_113"),
+	PINCTRL_PIN(114, "GPIO_114"),
+	PINCTRL_PIN(115, "GPIO_115"),
+	PINCTRL_PIN(116, "GPIO_116"),
+	PINCTRL_PIN(117, "GPIO_117"),
+	PINCTRL_PIN(118, "GPIO_118"),
+	PINCTRL_PIN(119, "GPIO_119"),
+	PINCTRL_PIN(120, "GPIO_120"),
+	PINCTRL_PIN(121, "GPIO_121"),
+	PINCTRL_PIN(122, "GPIO_122"),
+	PINCTRL_PIN(123, "GPIO_123"),
+	PINCTRL_PIN(124, "GPIO_124"),
+	PINCTRL_PIN(125, "GPIO_125"),
+	PINCTRL_PIN(126, "GPIO_126"),
+	PINCTRL_PIN(127, "GPIO_127"),
+	PINCTRL_PIN(128, "GPIO_128"),
+	PINCTRL_PIN(129, "GPIO_129"),
+	PINCTRL_PIN(130, "GPIO_130"),
+	PINCTRL_PIN(131, "GPIO_131"),
+	PINCTRL_PIN(132, "GPIO_132"),
+	PINCTRL_PIN(133, "GPIO_133"),
+	PINCTRL_PIN(134, "SDC1_CLK"),
+	PINCTRL_PIN(135, "SDC1_CMD"),
+	PINCTRL_PIN(136, "SDC1_DATA"),
+	PINCTRL_PIN(137, "SDC1_RCLK"),
+	PINCTRL_PIN(138, "SDC2_CLK"),
+	PINCTRL_PIN(139, "SDC2_CMD"),
+	PINCTRL_PIN(140, "SDC2_DATA"),
+	PINCTRL_PIN(141, "QDSD_CLK"),
+	PINCTRL_PIN(142, "QDSD_CMD"),
+	PINCTRL_PIN(143, "QDSD_DATA0"),
+	PINCTRL_PIN(144, "QDSD_DATA1"),
+	PINCTRL_PIN(145, "QDSD_DATA2"),
+	PINCTRL_PIN(146, "QDSD_DATA3"),
+};
+
+#define DECLARE_MSM_GPIO_PINS(pin)	\
+	static const unsigned int gpio##pin##_pins[] = { pin }
+
+DECLARE_MSM_GPIO_PINS(0);
+DECLARE_MSM_GPIO_PINS(1);
+DECLARE_MSM_GPIO_PINS(2);
+DECLARE_MSM_GPIO_PINS(3);
+DECLARE_MSM_GPIO_PINS(4);
+DECLARE_MSM_GPIO_PINS(5);
+DECLARE_MSM_GPIO_PINS(6);
+DECLARE_MSM_GPIO_PINS(7);
+DECLARE_MSM_GPIO_PINS(8);
+DECLARE_MSM_GPIO_PINS(9);
+DECLARE_MSM_GPIO_PINS(10);
+DECLARE_MSM_GPIO_PINS(11);
+DECLARE_MSM_GPIO_PINS(12);
+DECLARE_MSM_GPIO_PINS(13);
+DECLARE_MSM_GPIO_PINS(14);
+DECLARE_MSM_GPIO_PINS(15);
+DECLARE_MSM_GPIO_PINS(16);
+DECLARE_MSM_GPIO_PINS(17);
+DECLARE_MSM_GPIO_PINS(18);
+DECLARE_MSM_GPIO_PINS(19);
+DECLARE_MSM_GPIO_PINS(20);
+DECLARE_MSM_GPIO_PINS(21);
+DECLARE_MSM_GPIO_PINS(22);
+DECLARE_MSM_GPIO_PINS(23);
+DECLARE_MSM_GPIO_PINS(24);
+DECLARE_MSM_GPIO_PINS(25);
+DECLARE_MSM_GPIO_PINS(26);
+DECLARE_MSM_GPIO_PINS(27);
+DECLARE_MSM_GPIO_PINS(28);
+DECLARE_MSM_GPIO_PINS(29);
+DECLARE_MSM_GPIO_PINS(30);
+DECLARE_MSM_GPIO_PINS(31);
+DECLARE_MSM_GPIO_PINS(32);
+DECLARE_MSM_GPIO_PINS(33);
+DECLARE_MSM_GPIO_PINS(34);
+DECLARE_MSM_GPIO_PINS(35);
+DECLARE_MSM_GPIO_PINS(36);
+DECLARE_MSM_GPIO_PINS(37);
+DECLARE_MSM_GPIO_PINS(38);
+DECLARE_MSM_GPIO_PINS(39);
+DECLARE_MSM_GPIO_PINS(40);
+DECLARE_MSM_GPIO_PINS(41);
+DECLARE_MSM_GPIO_PINS(42);
+DECLARE_MSM_GPIO_PINS(43);
+DECLARE_MSM_GPIO_PINS(44);
+DECLARE_MSM_GPIO_PINS(45);
+DECLARE_MSM_GPIO_PINS(46);
+DECLARE_MSM_GPIO_PINS(47);
+DECLARE_MSM_GPIO_PINS(48);
+DECLARE_MSM_GPIO_PINS(49);
+DECLARE_MSM_GPIO_PINS(50);
+DECLARE_MSM_GPIO_PINS(51);
+DECLARE_MSM_GPIO_PINS(52);
+DECLARE_MSM_GPIO_PINS(53);
+DECLARE_MSM_GPIO_PINS(54);
+DECLARE_MSM_GPIO_PINS(55);
+DECLARE_MSM_GPIO_PINS(56);
+DECLARE_MSM_GPIO_PINS(57);
+DECLARE_MSM_GPIO_PINS(58);
+DECLARE_MSM_GPIO_PINS(59);
+DECLARE_MSM_GPIO_PINS(60);
+DECLARE_MSM_GPIO_PINS(61);
+DECLARE_MSM_GPIO_PINS(62);
+DECLARE_MSM_GPIO_PINS(63);
+DECLARE_MSM_GPIO_PINS(64);
+DECLARE_MSM_GPIO_PINS(65);
+DECLARE_MSM_GPIO_PINS(66);
+DECLARE_MSM_GPIO_PINS(67);
+DECLARE_MSM_GPIO_PINS(68);
+DECLARE_MSM_GPIO_PINS(69);
+DECLARE_MSM_GPIO_PINS(70);
+DECLARE_MSM_GPIO_PINS(71);
+DECLARE_MSM_GPIO_PINS(72);
+DECLARE_MSM_GPIO_PINS(73);
+DECLARE_MSM_GPIO_PINS(74);
+DECLARE_MSM_GPIO_PINS(75);
+DECLARE_MSM_GPIO_PINS(76);
+DECLARE_MSM_GPIO_PINS(77);
+DECLARE_MSM_GPIO_PINS(78);
+DECLARE_MSM_GPIO_PINS(79);
+DECLARE_MSM_GPIO_PINS(80);
+DECLARE_MSM_GPIO_PINS(81);
+DECLARE_MSM_GPIO_PINS(82);
+DECLARE_MSM_GPIO_PINS(83);
+DECLARE_MSM_GPIO_PINS(84);
+DECLARE_MSM_GPIO_PINS(85);
+DECLARE_MSM_GPIO_PINS(86);
+DECLARE_MSM_GPIO_PINS(87);
+DECLARE_MSM_GPIO_PINS(88);
+DECLARE_MSM_GPIO_PINS(89);
+DECLARE_MSM_GPIO_PINS(90);
+DECLARE_MSM_GPIO_PINS(91);
+DECLARE_MSM_GPIO_PINS(92);
+DECLARE_MSM_GPIO_PINS(93);
+DECLARE_MSM_GPIO_PINS(94);
+DECLARE_MSM_GPIO_PINS(95);
+DECLARE_MSM_GPIO_PINS(96);
+DECLARE_MSM_GPIO_PINS(97);
+DECLARE_MSM_GPIO_PINS(98);
+DECLARE_MSM_GPIO_PINS(99);
+DECLARE_MSM_GPIO_PINS(100);
+DECLARE_MSM_GPIO_PINS(101);
+DECLARE_MSM_GPIO_PINS(102);
+DECLARE_MSM_GPIO_PINS(103);
+DECLARE_MSM_GPIO_PINS(104);
+DECLARE_MSM_GPIO_PINS(105);
+DECLARE_MSM_GPIO_PINS(106);
+DECLARE_MSM_GPIO_PINS(107);
+DECLARE_MSM_GPIO_PINS(108);
+DECLARE_MSM_GPIO_PINS(109);
+DECLARE_MSM_GPIO_PINS(110);
+DECLARE_MSM_GPIO_PINS(111);
+DECLARE_MSM_GPIO_PINS(112);
+DECLARE_MSM_GPIO_PINS(113);
+DECLARE_MSM_GPIO_PINS(114);
+DECLARE_MSM_GPIO_PINS(115);
+DECLARE_MSM_GPIO_PINS(116);
+DECLARE_MSM_GPIO_PINS(117);
+DECLARE_MSM_GPIO_PINS(118);
+DECLARE_MSM_GPIO_PINS(119);
+DECLARE_MSM_GPIO_PINS(120);
+DECLARE_MSM_GPIO_PINS(121);
+DECLARE_MSM_GPIO_PINS(122);
+DECLARE_MSM_GPIO_PINS(123);
+DECLARE_MSM_GPIO_PINS(124);
+DECLARE_MSM_GPIO_PINS(125);
+DECLARE_MSM_GPIO_PINS(126);
+DECLARE_MSM_GPIO_PINS(127);
+DECLARE_MSM_GPIO_PINS(128);
+DECLARE_MSM_GPIO_PINS(129);
+DECLARE_MSM_GPIO_PINS(130);
+DECLARE_MSM_GPIO_PINS(131);
+DECLARE_MSM_GPIO_PINS(132);
+DECLARE_MSM_GPIO_PINS(133);
+
+static const unsigned int sdc1_clk_pins[] = { 134 };
+static const unsigned int sdc1_cmd_pins[] = { 135 };
+static const unsigned int sdc1_data_pins[] = { 136 };
+static const unsigned int sdc1_rclk_pins[] = { 137 };
+static const unsigned int sdc2_clk_pins[] = { 138 };
+static const unsigned int sdc2_cmd_pins[] = { 139 };
+static const unsigned int sdc2_data_pins[] = { 140 };
+static const unsigned int qdsd_clk_pins[] = { 141 };
+static const unsigned int qdsd_cmd_pins[] = { 142 };
+static const unsigned int qdsd_data0_pins[] = { 143 };
+static const unsigned int qdsd_data1_pins[] = { 144 };
+static const unsigned int qdsd_data2_pins[] = { 145 };
+static const unsigned int qdsd_data3_pins[] = { 146 };
+
+#define PINGROUP(id, f1, f2, f3, f4, f5, f6, f7, f8, f9)	\
+	{							\
+		.grp = PINCTRL_PINGROUP("gpio" #id,		\
+			gpio##id##_pins,			\
+			ARRAY_SIZE(gpio##id##_pins)),		\
+		.funcs = (int[]){				\
+			msm_mux_gpio,				\
+			msm_mux_##f1,				\
+			msm_mux_##f2,				\
+			msm_mux_##f3,				\
+			msm_mux_##f4,				\
+			msm_mux_##f5,				\
+			msm_mux_##f6,				\
+			msm_mux_##f7,				\
+			msm_mux_##f8,				\
+			msm_mux_##f9				\
+		},						\
+		.nfuncs = 10,					\
+		.ctl_reg = 0x1000 * id,				\
+		.io_reg = 0x4 + 0x1000 * id,			\
+		.intr_cfg_reg = 0x8 + 0x1000 * id,		\
+		.intr_status_reg = 0xc + 0x1000 * id,		\
+		.intr_target_reg = 0x8 + 0x1000 * id,		\
+		.mux_bit = 2,					\
+		.pull_bit = 0,					\
+		.drv_bit = 6,					\
+		.oe_bit = 9,					\
+		.in_bit = 0,					\
+		.out_bit = 1,					\
+		.intr_enable_bit = 0,				\
+		.intr_status_bit = 0,				\
+		.intr_target_bit = 5,				\
+		.intr_target_kpss_val = 4,			\
+		.intr_raw_status_bit = 4,			\
+		.intr_polarity_bit = 1,				\
+		.intr_detection_bit = 2,			\
+		.intr_detection_width = 2,			\
+	}
+
+#define SDC_PINGROUP(pg_name, ctl, pull, drv)	\
+	{					        \
+		.grp = PINCTRL_PINGROUP(#pg_name,	\
+			pg_name##_pins,			\
+			ARRAY_SIZE(pg_name##_pins)),	\
+		.ctl_reg = ctl,				\
+		.io_reg = 0,				\
+		.intr_cfg_reg = 0,			\
+		.intr_status_reg = 0,			\
+		.intr_target_reg = 0,			\
+		.mux_bit = -1,				\
+		.pull_bit = pull,			\
+		.drv_bit = drv,				\
+		.oe_bit = -1,				\
+		.in_bit = -1,				\
+		.out_bit = -1,				\
+		.intr_enable_bit = -1,			\
+		.intr_status_bit = -1,			\
+		.intr_target_bit = -1,			\
+		.intr_target_kpss_val = -1,		\
+		.intr_raw_status_bit = -1,		\
+		.intr_polarity_bit = -1,		\
+		.intr_detection_bit = -1,		\
+		.intr_detection_width = -1,		\
+	}
+
+enum msm8917_functions {
+	msm_mux_accel_int,
+	msm_mux_adsp_ext,
+	msm_mux_alsp_int,
+	msm_mux_atest_bbrx0,
+	msm_mux_atest_bbrx1,
+	msm_mux_atest_char,
+	msm_mux_atest_char0,
+	msm_mux_atest_char1,
+	msm_mux_atest_char2,
+	msm_mux_atest_char3,
+	msm_mux_atest_combodac_to_gpio_native,
+	msm_mux_atest_gpsadc_dtest0_native,
+	msm_mux_atest_gpsadc_dtest1_native,
+	msm_mux_atest_tsens,
+	msm_mux_atest_wlan0,
+	msm_mux_atest_wlan1,
+	msm_mux_audio_ref,
+	msm_mux_audio_reset,
+	msm_mux_bimc_dte0,
+	msm_mux_bimc_dte1,
+	msm_mux_blsp6_spi,
+	msm_mux_blsp8_spi,
+	msm_mux_blsp_i2c1,
+	msm_mux_blsp_i2c2,
+	msm_mux_blsp_i2c3,
+	msm_mux_blsp_i2c4,
+	msm_mux_blsp_i2c5,
+	msm_mux_blsp_i2c6,
+	msm_mux_blsp_i2c7,
+	msm_mux_blsp_i2c8,
+	msm_mux_blsp_spi1,
+	msm_mux_blsp_spi2,
+	msm_mux_blsp_spi3,
+	msm_mux_blsp_spi4,
+	msm_mux_blsp_spi5,
+	msm_mux_blsp_spi6,
+	msm_mux_blsp_spi7,
+	msm_mux_blsp_spi8,
+	msm_mux_blsp_uart1,
+	msm_mux_blsp_uart2,
+	msm_mux_blsp_uart3,
+	msm_mux_blsp_uart4,
+	msm_mux_blsp_uart5,
+	msm_mux_blsp_uart6,
+	msm_mux_blsp_uart7,
+	msm_mux_blsp_uart8,
+	msm_mux_cam0_ldo,
+	msm_mux_cam1_rst,
+	msm_mux_cam1_standby,
+	msm_mux_cam2_rst,
+	msm_mux_cam2_standby,
+	msm_mux_cam_mclk,
+	msm_mux_cci_async,
+	msm_mux_cci_i2c,
+	msm_mux_cci_timer0,
+	msm_mux_cci_timer1,
+	msm_mux_cdc_pdm0,
+	msm_mux_codec_int1,
+	msm_mux_codec_int2,
+	msm_mux_codec_mad,
+	msm_mux_coex_uart,
+	msm_mux_cri_trng,
+	msm_mux_cri_trng0,
+	msm_mux_cri_trng1,
+	msm_mux_dbg_out,
+	msm_mux_dmic0_clk,
+	msm_mux_dmic0_data,
+	msm_mux_ebi_cdc,
+	msm_mux_ebi_ch0,
+	msm_mux_ext_lpass,
+	msm_mux_forced_usb,
+	msm_mux_fp_gpio,
+	msm_mux_fp_int,
+	msm_mux_gcc_gp1_clk_a,
+	msm_mux_gcc_gp1_clk_b,
+	msm_mux_gcc_gp2_clk_a,
+	msm_mux_gcc_gp2_clk_b,
+	msm_mux_gcc_gp3_clk_a,
+	msm_mux_gcc_gp3_clk_b,
+	msm_mux_gcc_plltest,
+	msm_mux_gcc_tlmm,
+	msm_mux_gpio,
+	msm_mux_gsm0_tx,
+	msm_mux_key_focus,
+	msm_mux_key_snapshot,
+	msm_mux_key_volp,
+	msm_mux_ldo_en,
+	msm_mux_ldo_update,
+	msm_mux_lpass_slimbus,
+	msm_mux_lpass_slimbus0,
+	msm_mux_lpass_slimbus1,
+	msm_mux_m_voc,
+	msm_mux_mag_int,
+	msm_mux_mdp_vsync,
+	msm_mux_mipi_dsi0,
+	msm_mux_modem_tsync,
+	msm_mux_nav_pps,
+	msm_mux_nav_pps_in_a,
+	msm_mux_nav_pps_in_b,
+	msm_mux_nav_tsync,
+	msm_mux_nfc_pwr,
+	msm_mux_ov_ldo,
+	msm_mux_pa_indicator,
+	msm_mux_pbs0,
+	msm_mux_pbs1,
+	msm_mux_pbs2,
+	msm_mux_pri_mi2s,
+	msm_mux_pri_mi2s_mclk_a,
+	msm_mux_pri_mi2s_mclk_b,
+	msm_mux_pri_mi2s_ws,
+	msm_mux_prng_rosc,
+	msm_mux_pwr_crypto_enabled_a,
+	msm_mux_pwr_crypto_enabled_b,
+	msm_mux_pwr_modem_enabled_a,
+	msm_mux_pwr_modem_enabled_b,
+	msm_mux_pwr_nav_enabled_a,
+	msm_mux_pwr_nav_enabled_b,
+	msm_mux_qdss_cti_trig_in_a0,
+	msm_mux_qdss_cti_trig_in_a1,
+	msm_mux_qdss_cti_trig_in_b0,
+	msm_mux_qdss_cti_trig_in_b1,
+	msm_mux_qdss_cti_trig_out_a0,
+	msm_mux_qdss_cti_trig_out_a1,
+	msm_mux_qdss_cti_trig_out_b0,
+	msm_mux_qdss_cti_trig_out_b1,
+	msm_mux_qdss_traceclk_a,
+	msm_mux_qdss_traceclk_b,
+	msm_mux_qdss_tracectl_a,
+	msm_mux_qdss_tracectl_b,
+	msm_mux_qdss_tracedata_a,
+	msm_mux_qdss_tracedata_b,
+	msm_mux_sd_write,
+	msm_mux_sdcard_det,
+	msm_mux_sec_mi2s,
+	msm_mux_sec_mi2s_mclk_a,
+	msm_mux_sec_mi2s_mclk_b,
+	msm_mux_sensor_rst,
+	msm_mux_smb_int,
+	msm_mux_ssbi_wtr1,
+	msm_mux_ts_resout,
+	msm_mux_ts_sample,
+	msm_mux_uim1_clk,
+	msm_mux_uim1_data,
+	msm_mux_uim1_present,
+	msm_mux_uim1_reset,
+	msm_mux_uim2_clk,
+	msm_mux_uim2_data,
+	msm_mux_uim2_present,
+	msm_mux_uim2_reset,
+	msm_mux_uim_batt,
+	msm_mux_us_emitter,
+	msm_mux_us_euro,
+	msm_mux_wcss_bt,
+	msm_mux_wcss_fm,
+	msm_mux_wcss_wlan,
+	msm_mux_wcss_wlan0,
+	msm_mux_wcss_wlan1,
+	msm_mux_wcss_wlan2,
+	msm_mux_webcam_rst,
+	msm_mux_webcam_standby,
+	msm_mux_wsa_io,
+	msm_mux_wsa_irq,
+	msm_mux_NA,
+};
+
+static const char * const qdss_tracedata_b_groups[] = {
+	"gpio0", "gpio1", "gpio6", "gpio7", "gpio12", "gpio13", "gpio23",
+	"gpio42", "gpio43", "gpio44", "gpio47", "gpio66", "gpio86", "gpio87",
+	"gpio88", "gpio92",
+};
+
+static const char * const blsp_uart1_groups[] = {
+	"gpio0", "gpio1", "gpio2", "gpio3",
+};
+
+static const char * const gpio_groups[] = {
+	"gpio0", "gpio1", "gpio2", "gpio3", "gpio4", "gpio5", "gpio6", "gpio7",
+	"gpio8", "gpio9", "gpio10", "gpio11", "gpio12", "gpio13", "gpio14",
+	"gpio15", "gpio16", "gpio17", "gpio18", "gpio19", "gpio20", "gpio21",
+	"gpio22", "gpio23", "gpio24", "gpio25", "gpio26", "gpio27", "gpio28",
+	"gpio29", "gpio30", "gpio31", "gpio32", "gpio33", "gpio34", "gpio35",
+	"gpio36", "gpio37", "gpio38", "gpio39", "gpio40", "gpio41", "gpio42",
+	"gpio43", "gpio44", "gpio45", "gpio46", "gpio47", "gpio48", "gpio49",
+	"gpio50", "gpio51", "gpio52", "gpio53", "gpio54", "gpio55", "gpio56",
+	"gpio57", "gpio58", "gpio59", "gpio60", "gpio61", "gpio62", "gpio63",
+	"gpio64", "gpio65", "gpio66", "gpio67", "gpio68", "gpio69", "gpio70",
+	"gpio71", "gpio72", "gpio73", "gpio74", "gpio75", "gpio76", "gpio77",
+	"gpio78", "gpio79", "gpio80", "gpio81", "gpio82", "gpio83", "gpio84",
+	"gpio85", "gpio86", "gpio87", "gpio88", "gpio89", "gpio90", "gpio91",
+	"gpio92", "gpio93", "gpio94", "gpio95", "gpio96", "gpio97", "gpio98",
+	"gpio99", "gpio100", "gpio101", "gpio102", "gpio103", "gpio104",
+	"gpio105", "gpio106", "gpio107", "gpio108", "gpio109", "gpio110",
+	"gpio111", "gpio112", "gpio113", "gpio114", "gpio115", "gpio116",
+	"gpio117", "gpio118", "gpio119", "gpio120", "gpio121", "gpio122",
+	"gpio123", "gpio124", "gpio125", "gpio126", "gpio127", "gpio128",
+	"gpio129", "gpio130", "gpio131", "gpio132", "gpio133",
+};
+
+static const char * const blsp_spi1_groups[] = {
+	"gpio0", "gpio1", "gpio2", "gpio3",
+};
+
+static const char * const adsp_ext_groups[] = {
+	"gpio1",
+};
+
+static const char * const blsp_i2c1_groups[] = {
+	"gpio2", "gpio3",
+};
+
+static const char * const prng_rosc_groups[] = {
+	"gpio2",
+};
+
+static const char * const qdss_cti_trig_out_b0_groups[] = {
+	"gpio2",
+};
+
+static const char * const blsp_spi2_groups[] = {
+	"gpio4", "gpio5", "gpio6", "gpio7",
+};
+
+static const char * const blsp_uart2_groups[] = {
+	"gpio4", "gpio5", "gpio6", "gpio7",
+};
+
+static const char * const blsp_uart3_groups[] = {
+	"gpio8", "gpio9", "gpio10", "gpio11",
+};
+
+static const char * const pbs0_groups[] = {
+	"gpio8",
+};
+
+static const char * const pbs1_groups[] = {
+	"gpio9",
+};
+
+static const char * const pwr_modem_enabled_b_groups[] = {
+	"gpio9",
+};
+
+static const char * const blsp_i2c3_groups[] = {
+	"gpio10", "gpio11",
+};
+
+static const char * const gcc_gp2_clk_b_groups[] = {
+	"gpio10",
+};
+
+static const char * const ldo_update_groups[] = {
+	"gpio4",
+};
+
+static const char * const atest_combodac_to_gpio_native_groups[] = {
+	"gpio4", "gpio12", "gpio13", "gpio20", "gpio21", "gpio28", "gpio29",
+	"gpio30", "gpio39", "gpio40", "gpio41", "gpio42", "gpio43", "gpio44",
+	"gpio45", "gpio46", "gpio47", "gpio48", "gpio67", "gpio115",
+};
+
+static const char * const ldo_en_groups[] = {
+	"gpio5",
+};
+
+static const char * const blsp_i2c2_groups[] = {
+	"gpio6", "gpio7",
+};
+
+static const char * const gcc_gp1_clk_b_groups[] = {
+	"gpio6",
+};
+
+static const char * const pbs2_groups[] = {
+	"gpio7",
+};
+
+static const char * const atest_gpsadc_dtest0_native_groups[] = {
+	"gpio7",
+};
+
+static const char * const blsp_spi3_groups[] = {
+	"gpio8", "gpio9", "gpio10", "gpio11",
+};
+
+static const char * const gcc_gp3_clk_b_groups[] = {
+	"gpio11",
+};
+
+static const char * const blsp_spi4_groups[] = {
+	"gpio12", "gpio13", "gpio14", "gpio15",
+};
+
+static const char * const blsp_uart4_groups[] = {
+	"gpio12", "gpio13", "gpio14", "gpio15",
+};
+
+static const char * const sec_mi2s_groups[] = {
+	"gpio12", "gpio13", "gpio94", "gpio95",
+};
+
+static const char * const pwr_nav_enabled_b_groups[] = {
+	"gpio12",
+};
+
+static const char * const codec_mad_groups[] = {
+	"gpio13",
+};
+
+static const char * const pwr_crypto_enabled_b_groups[] = {
+	"gpio13",
+};
+
+static const char * const blsp_i2c4_groups[] = {
+	"gpio14", "gpio15",
+};
+
+static const char * const blsp_spi5_groups[] = {
+	"gpio16", "gpio17", "gpio18", "gpio19",
+};
+
+static const char * const blsp_uart5_groups[] = {
+	"gpio16", "gpio17", "gpio18", "gpio19",
+};
+
+static const char * const qdss_traceclk_a_groups[] = {
+	"gpio16",
+};
+
+static const char * const atest_bbrx1_groups[] = {
+	"gpio16",
+};
+
+static const char * const m_voc_groups[] = {
+	"gpio17", "gpio21",
+};
+
+static const char * const qdss_cti_trig_in_a0_groups[] = {
+	"gpio17",
+};
+
+static const char * const qdss_cti_trig_in_b0_groups[] = {
+	"gpio21",
+};
+
+static const char * const blsp_i2c6_groups[] = {
+	"gpio22", "gpio23",
+};
+
+static const char * const qdss_traceclk_b_groups[] = {
+	"gpio22",
+};
+
+static const char * const atest_wlan0_groups[] = {
+	"gpio22",
+};
+
+static const char * const atest_bbrx0_groups[] = {
+	"gpio17",
+};
+
+static const char * const blsp_i2c5_groups[] = {
+	"gpio18", "gpio19",
+};
+
+static const char * const qdss_tracectl_a_groups[] = {
+	"gpio18",
+};
+
+static const char * const atest_gpsadc_dtest1_native_groups[] = {
+	"gpio18",
+};
+
+static const char * const qdss_tracedata_a_groups[] = {
+	"gpio19", "gpio26", "gpio27", "gpio28", "gpio29", "gpio30", "gpio31",
+	"gpio32", "gpio33", "gpio34", "gpio35", "gpio36", "gpio38", "gpio39",
+	"gpio40", "gpio50",
+};
+
+static const char * const blsp_spi6_groups[] = {
+	"gpio20", "gpio21", "gpio22", "gpio23",
+};
+
+static const char * const blsp_uart6_groups[] = {
+	"gpio20", "gpio21", "gpio22", "gpio23",
+};
+
+static const char * const qdss_tracectl_b_groups[] = {
+	"gpio20",
+};
+
+static const char * const atest_wlan1_groups[] = {
+	"gpio23",
+};
+
+static const char * const mdp_vsync_groups[] = {
+	"gpio24", "gpio25",
+};
+
+static const char * const pri_mi2s_mclk_a_groups[] = {
+	"gpio25",
+};
+
+static const char * const sec_mi2s_mclk_a_groups[] = {
+	"gpio25",
+};
+
+static const char * const cam_mclk_groups[] = {
+	"gpio26", "gpio27", "gpio28",
+};
+
+static const char * const cci_i2c_groups[] = {
+	"gpio29", "gpio30", "gpio31", "gpio32",
+};
+
+static const char * const pwr_modem_enabled_a_groups[] = {
+	"gpio29",
+};
+
+static const char * const cci_timer0_groups[] = {
+	"gpio33",
+};
+
+static const char * const cci_timer1_groups[] = {
+	"gpio34",
+};
+
+static const char * const cam1_standby_groups[] = {
+	"gpio35",
+};
+
+static const char * const pwr_nav_enabled_a_groups[] = {
+	"gpio35",
+};
+
+static const char * const cam1_rst_groups[] = {
+	"gpio36",
+};
+
+static const char * const pwr_crypto_enabled_a_groups[] = {
+	"gpio36",
+};
+
+static const char * const forced_usb_groups[] = {
+	"gpio37",
+};
+
+static const char * const qdss_cti_trig_out_b1_groups[] = {
+	"gpio37",
+};
+
+static const char * const cam2_rst_groups[] = {
+	"gpio38",
+};
+
+static const char * const webcam_standby_groups[] = {
+	"gpio39",
+};
+
+static const char * const cci_async_groups[] = {
+	"gpio39",
+};
+
+static const char * const webcam_rst_groups[] = {
+	"gpio40",
+};
+
+static const char * const ov_ldo_groups[] = {
+	"gpio41",
+};
+
+static const char * const sd_write_groups[] = {
+	"gpio41",
+};
+
+static const char * const accel_int_groups[] = {
+	"gpio42",
+};
+
+static const char * const gcc_gp1_clk_a_groups[] = {
+	"gpio42",
+};
+
+static const char * const alsp_int_groups[] = {
+	"gpio43",
+};
+
+static const char * const gcc_gp2_clk_a_groups[] = {
+	"gpio43",
+};
+
+static const char * const mag_int_groups[] = {
+	"gpio44",
+};
+
+static const char * const gcc_gp3_clk_a_groups[] = {
+	"gpio44",
+};
+
+static const char * const blsp6_spi_groups[] = {
+	"gpio47",
+};
+
+static const char * const fp_int_groups[] = {
+	"gpio48",
+};
+
+static const char * const qdss_cti_trig_in_b1_groups[] = {
+	"gpio48",
+};
+
+static const char * const uim_batt_groups[] = {
+	"gpio49",
+};
+
+static const char * const cam2_standby_groups[] = {
+	"gpio50",
+};
+
+static const char * const uim1_data_groups[] = {
+	"gpio51",
+};
+
+static const char * const uim1_clk_groups[] = {
+	"gpio52",
+};
+
+static const char * const uim1_reset_groups[] = {
+	"gpio53",
+};
+
+static const char * const uim1_present_groups[] = {
+	"gpio54",
+};
+
+static const char * const uim2_data_groups[] = {
+	"gpio55",
+};
+
+static const char * const uim2_clk_groups[] = {
+	"gpio56",
+};
+
+static const char * const uim2_reset_groups[] = {
+	"gpio57",
+};
+
+static const char * const uim2_present_groups[] = {
+	"gpio58",
+};
+
+static const char * const sensor_rst_groups[] = {
+	"gpio59",
+};
+
+static const char * const mipi_dsi0_groups[] = {
+	"gpio60",
+};
+
+static const char * const smb_int_groups[] = {
+	"gpio61",
+};
+
+static const char * const cam0_ldo_groups[] = {
+	"gpio62",
+};
+
+static const char * const us_euro_groups[] = {
+	"gpio63",
+};
+
+static const char * const atest_char3_groups[] = {
+	"gpio63",
+};
+
+static const char * const dbg_out_groups[] = {
+	"gpio63",
+};
+
+static const char * const bimc_dte0_groups[] = {
+	"gpio63", "gpio65",
+};
+
+static const char * const ts_resout_groups[] = {
+	"gpio64",
+};
+
+static const char * const ts_sample_groups[] = {
+	"gpio65",
+};
+
+static const char * const sec_mi2s_mclk_b_groups[] = {
+	"gpio66",
+};
+
+static const char * const pri_mi2s_groups[] = {
+	"gpio66", "gpio85", "gpio86", "gpio88", "gpio94", "gpio95",
+};
+
+static const char * const sdcard_det_groups[] = {
+	"gpio67",
+};
+
+static const char * const atest_char1_groups[] = {
+	"gpio67",
+};
+
+static const char * const ebi_cdc_groups[] = {
+	"gpio67", "gpio69", "gpio118", "gpio119", "gpio120", "gpio123",
+};
+
+static const char * const audio_reset_groups[] = {
+	"gpio68",
+};
+
+static const char * const atest_char0_groups[] = {
+	"gpio68",
+};
+
+static const char * const audio_ref_groups[] = {
+	"gpio69",
+};
+
+static const char * const cdc_pdm0_groups[] = {
+	"gpio69", "gpio70", "gpio71", "gpio72", "gpio73", "gpio74",
+};
+
+static const char * const pri_mi2s_mclk_b_groups[] = {
+	"gpio69",
+};
+
+static const char * const lpass_slimbus_groups[] = {
+	"gpio70",
+};
+
+static const char * const lpass_slimbus0_groups[] = {
+	"gpio71",
+};
+
+static const char * const lpass_slimbus1_groups[] = {
+	"gpio72",
+};
+
+static const char * const codec_int1_groups[] = {
+	"gpio73",
+};
+
+static const char * const codec_int2_groups[] = {
+	"gpio74",
+};
+
+static const char * const wcss_bt_groups[] = {
+	"gpio75", "gpio83", "gpio84",
+};
+
+static const char * const atest_char2_groups[] = {
+	"gpio75",
+};
+
+static const char * const ebi_ch0_groups[] = {
+	"gpio75",
+};
+
+static const char * const wcss_wlan2_groups[] = {
+	"gpio76",
+};
+
+static const char * const wcss_wlan1_groups[] = {
+	"gpio77",
+};
+
+static const char * const wcss_wlan0_groups[] = {
+	"gpio78",
+};
+
+static const char * const wcss_wlan_groups[] = {
+	"gpio79", "gpio80",
+};
+
+static const char * const wcss_fm_groups[] = {
+	"gpio81", "gpio82",
+};
+
+static const char * const ext_lpass_groups[] = {
+	"gpio81",
+};
+
+static const char * const cri_trng_groups[] = {
+	"gpio82",
+};
+
+static const char * const cri_trng1_groups[] = {
+	"gpio83",
+};
+
+static const char * const cri_trng0_groups[] = {
+	"gpio84",
+};
+
+static const char * const blsp_spi7_groups[] = {
+	"gpio85", "gpio86", "gpio87", "gpio88",
+};
+
+static const char * const blsp_uart7_groups[] = {
+	"gpio85", "gpio86", "gpio87", "gpio88",
+};
+
+static const char * const pri_mi2s_ws_groups[] = {
+	"gpio87",
+};
+
+static const char * const blsp_i2c7_groups[] = {
+	"gpio87", "gpio88",
+};
+
+static const char * const gcc_tlmm_groups[] = {
+	"gpio87",
+};
+
+static const char * const dmic0_clk_groups[] = {
+	"gpio89",
+};
+
+static const char * const dmic0_data_groups[] = {
+	"gpio90",
+};
+
+static const char * const key_volp_groups[] = {
+	"gpio91",
+};
+
+static const char * const qdss_cti_trig_in_a1_groups[] = {
+	"gpio91",
+};
+
+static const char * const us_emitter_groups[] = {
+	"gpio92",
+};
+
+static const char * const wsa_irq_groups[] = {
+	"gpio93",
+};
+
+static const char * const wsa_io_groups[] = {
+	"gpio94", "gpio95",
+};
+
+static const char * const blsp_spi8_groups[] = {
+	"gpio96", "gpio97", "gpio98", "gpio99",
+};
+
+static const char * const blsp_uart8_groups[] = {
+	"gpio96", "gpio97", "gpio98", "gpio99",
+};
+
+static const char * const blsp_i2c8_groups[] = {
+	"gpio98", "gpio99",
+};
+
+static const char * const gcc_plltest_groups[] = {
+	"gpio98", "gpio99",
+};
+
+static const char * const nav_pps_in_a_groups[] = {
+	"gpio115",
+};
+
+static const char * const pa_indicator_groups[] = {
+	"gpio116",
+};
+
+static const char * const modem_tsync_groups[] = {
+	"gpio117",
+};
+
+static const char * const nav_tsync_groups[] = {
+	"gpio117",
+};
+
+static const char * const nav_pps_in_b_groups[] = {
+	"gpio117",
+};
+
+static const char * const nav_pps_groups[] = {
+	"gpio117",
+};
+
+static const char * const gsm0_tx_groups[] = {
+	"gpio119",
+};
+
+static const char * const atest_char_groups[] = {
+	"gpio120",
+};
+
+static const char * const atest_tsens_groups[] = {
+	"gpio120",
+};
+
+static const char * const bimc_dte1_groups[] = {
+	"gpio121", "gpio122",
+};
+
+static const char * const ssbi_wtr1_groups[] = {
+	"gpio122", "gpio123",
+};
+
+static const char * const fp_gpio_groups[] = {
+	"gpio124",
+};
+
+static const char * const coex_uart_groups[] = {
+	"gpio124", "gpio127",
+};
+
+static const char * const key_snapshot_groups[] = {
+	"gpio127",
+};
+
+static const char * const key_focus_groups[] = {
+	"gpio128",
+};
+
+static const char * const nfc_pwr_groups[] = {
+	"gpio129",
+};
+
+static const char * const blsp8_spi_groups[] = {
+	"gpio130",
+};
+
+static const char * const qdss_cti_trig_out_a0_groups[] = {
+	"gpio132",
+};
+
+static const char * const qdss_cti_trig_out_a1_groups[] = {
+	"gpio133",
+};
+
+static const struct pinfunction msm8917_functions[] = {
+	MSM_PIN_FUNCTION(accel_int),
+	MSM_PIN_FUNCTION(adsp_ext),
+	MSM_PIN_FUNCTION(alsp_int),
+	MSM_PIN_FUNCTION(atest_bbrx0),
+	MSM_PIN_FUNCTION(atest_bbrx1),
+	MSM_PIN_FUNCTION(atest_char),
+	MSM_PIN_FUNCTION(atest_char0),
+	MSM_PIN_FUNCTION(atest_char1),
+	MSM_PIN_FUNCTION(atest_char2),
+	MSM_PIN_FUNCTION(atest_char3),
+	MSM_PIN_FUNCTION(atest_combodac_to_gpio_native),
+	MSM_PIN_FUNCTION(atest_gpsadc_dtest0_native),
+	MSM_PIN_FUNCTION(atest_gpsadc_dtest1_native),
+	MSM_PIN_FUNCTION(atest_tsens),
+	MSM_PIN_FUNCTION(atest_wlan0),
+	MSM_PIN_FUNCTION(atest_wlan1),
+	MSM_PIN_FUNCTION(audio_ref),
+	MSM_PIN_FUNCTION(audio_reset),
+	MSM_PIN_FUNCTION(bimc_dte0),
+	MSM_PIN_FUNCTION(bimc_dte1),
+	MSM_PIN_FUNCTION(blsp6_spi),
+	MSM_PIN_FUNCTION(blsp8_spi),
+	MSM_PIN_FUNCTION(blsp_i2c1),
+	MSM_PIN_FUNCTION(blsp_i2c2),
+	MSM_PIN_FUNCTION(blsp_i2c3),
+	MSM_PIN_FUNCTION(blsp_i2c4),
+	MSM_PIN_FUNCTION(blsp_i2c5),
+	MSM_PIN_FUNCTION(blsp_i2c6),
+	MSM_PIN_FUNCTION(blsp_i2c7),
+	MSM_PIN_FUNCTION(blsp_i2c8),
+	MSM_PIN_FUNCTION(blsp_spi1),
+	MSM_PIN_FUNCTION(blsp_spi2),
+	MSM_PIN_FUNCTION(blsp_spi3),
+	MSM_PIN_FUNCTION(blsp_spi4),
+	MSM_PIN_FUNCTION(blsp_spi5),
+	MSM_PIN_FUNCTION(blsp_spi6),
+	MSM_PIN_FUNCTION(blsp_spi7),
+	MSM_PIN_FUNCTION(blsp_spi8),
+	MSM_PIN_FUNCTION(blsp_uart1),
+	MSM_PIN_FUNCTION(blsp_uart2),
+	MSM_PIN_FUNCTION(blsp_uart3),
+	MSM_PIN_FUNCTION(blsp_uart4),
+	MSM_PIN_FUNCTION(blsp_uart5),
+	MSM_PIN_FUNCTION(blsp_uart6),
+	MSM_PIN_FUNCTION(blsp_uart7),
+	MSM_PIN_FUNCTION(blsp_uart8),
+	MSM_PIN_FUNCTION(cam0_ldo),
+	MSM_PIN_FUNCTION(cam1_rst),
+	MSM_PIN_FUNCTION(cam1_standby),
+	MSM_PIN_FUNCTION(cam2_rst),
+	MSM_PIN_FUNCTION(cam2_standby),
+	MSM_PIN_FUNCTION(cam_mclk),
+	MSM_PIN_FUNCTION(cci_async),
+	MSM_PIN_FUNCTION(cci_i2c),
+	MSM_PIN_FUNCTION(cci_timer0),
+	MSM_PIN_FUNCTION(cci_timer1),
+	MSM_PIN_FUNCTION(cdc_pdm0),
+	MSM_PIN_FUNCTION(codec_int1),
+	MSM_PIN_FUNCTION(codec_int2),
+	MSM_PIN_FUNCTION(codec_mad),
+	MSM_PIN_FUNCTION(coex_uart),
+	MSM_PIN_FUNCTION(cri_trng),
+	MSM_PIN_FUNCTION(cri_trng0),
+	MSM_PIN_FUNCTION(cri_trng1),
+	MSM_PIN_FUNCTION(dbg_out),
+	MSM_PIN_FUNCTION(dmic0_clk),
+	MSM_PIN_FUNCTION(dmic0_data),
+	MSM_PIN_FUNCTION(ebi_cdc),
+	MSM_PIN_FUNCTION(ebi_ch0),
+	MSM_PIN_FUNCTION(ext_lpass),
+	MSM_PIN_FUNCTION(forced_usb),
+	MSM_PIN_FUNCTION(fp_gpio),
+	MSM_PIN_FUNCTION(fp_int),
+	MSM_PIN_FUNCTION(gcc_gp1_clk_a),
+	MSM_PIN_FUNCTION(gcc_gp1_clk_b),
+	MSM_PIN_FUNCTION(gcc_gp2_clk_a),
+	MSM_PIN_FUNCTION(gcc_gp2_clk_b),
+	MSM_PIN_FUNCTION(gcc_gp3_clk_a),
+	MSM_PIN_FUNCTION(gcc_gp3_clk_b),
+	MSM_PIN_FUNCTION(gcc_plltest),
+	MSM_PIN_FUNCTION(gcc_tlmm),
+	MSM_PIN_FUNCTION(gpio),
+	MSM_PIN_FUNCTION(gsm0_tx),
+	MSM_PIN_FUNCTION(key_focus),
+	MSM_PIN_FUNCTION(key_snapshot),
+	MSM_PIN_FUNCTION(key_volp),
+	MSM_PIN_FUNCTION(ldo_en),
+	MSM_PIN_FUNCTION(ldo_update),
+	MSM_PIN_FUNCTION(lpass_slimbus),
+	MSM_PIN_FUNCTION(lpass_slimbus0),
+	MSM_PIN_FUNCTION(lpass_slimbus1),
+	MSM_PIN_FUNCTION(m_voc),
+	MSM_PIN_FUNCTION(mag_int),
+	MSM_PIN_FUNCTION(mdp_vsync),
+	MSM_PIN_FUNCTION(mipi_dsi0),
+	MSM_PIN_FUNCTION(modem_tsync),
+	MSM_PIN_FUNCTION(nav_pps),
+	MSM_PIN_FUNCTION(nav_pps_in_a),
+	MSM_PIN_FUNCTION(nav_pps_in_b),
+	MSM_PIN_FUNCTION(nav_tsync),
+	MSM_PIN_FUNCTION(nfc_pwr),
+	MSM_PIN_FUNCTION(ov_ldo),
+	MSM_PIN_FUNCTION(pa_indicator),
+	MSM_PIN_FUNCTION(pbs0),
+	MSM_PIN_FUNCTION(pbs1),
+	MSM_PIN_FUNCTION(pbs2),
+	MSM_PIN_FUNCTION(pri_mi2s),
+	MSM_PIN_FUNCTION(pri_mi2s_mclk_a),
+	MSM_PIN_FUNCTION(pri_mi2s_mclk_b),
+	MSM_PIN_FUNCTION(pri_mi2s_ws),
+	MSM_PIN_FUNCTION(prng_rosc),
+	MSM_PIN_FUNCTION(pwr_crypto_enabled_a),
+	MSM_PIN_FUNCTION(pwr_crypto_enabled_b),
+	MSM_PIN_FUNCTION(pwr_modem_enabled_a),
+	MSM_PIN_FUNCTION(pwr_modem_enabled_b),
+	MSM_PIN_FUNCTION(pwr_nav_enabled_a),
+	MSM_PIN_FUNCTION(pwr_nav_enabled_b),
+	MSM_PIN_FUNCTION(qdss_cti_trig_in_a0),
+	MSM_PIN_FUNCTION(qdss_cti_trig_in_a1),
+	MSM_PIN_FUNCTION(qdss_cti_trig_in_b0),
+	MSM_PIN_FUNCTION(qdss_cti_trig_in_b1),
+	MSM_PIN_FUNCTION(qdss_cti_trig_out_a0),
+	MSM_PIN_FUNCTION(qdss_cti_trig_out_a1),
+	MSM_PIN_FUNCTION(qdss_cti_trig_out_b0),
+	MSM_PIN_FUNCTION(qdss_cti_trig_out_b1),
+	MSM_PIN_FUNCTION(qdss_traceclk_a),
+	MSM_PIN_FUNCTION(qdss_traceclk_b),
+	MSM_PIN_FUNCTION(qdss_tracectl_a),
+	MSM_PIN_FUNCTION(qdss_tracectl_b),
+	MSM_PIN_FUNCTION(qdss_tracedata_a),
+	MSM_PIN_FUNCTION(qdss_tracedata_b),
+	MSM_PIN_FUNCTION(sd_write),
+	MSM_PIN_FUNCTION(sdcard_det),
+	MSM_PIN_FUNCTION(sec_mi2s),
+	MSM_PIN_FUNCTION(sec_mi2s_mclk_a),
+	MSM_PIN_FUNCTION(sec_mi2s_mclk_b),
+	MSM_PIN_FUNCTION(sensor_rst),
+	MSM_PIN_FUNCTION(smb_int),
+	MSM_PIN_FUNCTION(ssbi_wtr1),
+	MSM_PIN_FUNCTION(ts_resout),
+	MSM_PIN_FUNCTION(ts_sample),
+	MSM_PIN_FUNCTION(uim1_clk),
+	MSM_PIN_FUNCTION(uim1_data),
+	MSM_PIN_FUNCTION(uim1_present),
+	MSM_PIN_FUNCTION(uim1_reset),
+	MSM_PIN_FUNCTION(uim2_clk),
+	MSM_PIN_FUNCTION(uim2_data),
+	MSM_PIN_FUNCTION(uim2_present),
+	MSM_PIN_FUNCTION(uim2_reset),
+	MSM_PIN_FUNCTION(uim_batt),
+	MSM_PIN_FUNCTION(us_emitter),
+	MSM_PIN_FUNCTION(us_euro),
+	MSM_PIN_FUNCTION(wcss_bt),
+	MSM_PIN_FUNCTION(wcss_fm),
+	MSM_PIN_FUNCTION(wcss_wlan),
+	MSM_PIN_FUNCTION(wcss_wlan0),
+	MSM_PIN_FUNCTION(wcss_wlan1),
+	MSM_PIN_FUNCTION(wcss_wlan2),
+	MSM_PIN_FUNCTION(webcam_rst),
+	MSM_PIN_FUNCTION(webcam_standby),
+	MSM_PIN_FUNCTION(wsa_io),
+	MSM_PIN_FUNCTION(wsa_irq),
+};
+
+static const struct msm_pingroup msm8917_groups[] = {
+	PINGROUP(0, blsp_spi1, blsp_uart1, qdss_tracedata_b, NA, NA, NA, NA,
+		 NA, NA),
+	PINGROUP(1, blsp_spi1, blsp_uart1, adsp_ext, NA, NA, NA, NA, NA,
+		 qdss_tracedata_b),
+	PINGROUP(2, blsp_spi1, blsp_uart1, blsp_i2c1, prng_rosc, NA, NA, NA,
+		 NA, NA),
+	PINGROUP(3, blsp_spi1, blsp_uart1, blsp_i2c1, NA, NA, NA, NA, NA, NA),
+	PINGROUP(4, blsp_spi2, blsp_uart2, ldo_update, NA,
+		 atest_combodac_to_gpio_native, NA, NA, NA, NA),
+	PINGROUP(5, blsp_spi2, blsp_uart2, ldo_en, NA, NA, NA, NA, NA, NA),
+	PINGROUP(6, blsp_spi2, blsp_uart2, blsp_i2c2, gcc_gp1_clk_b,
+		 qdss_tracedata_b, NA, NA, NA, NA),
+	PINGROUP(7, blsp_spi2, blsp_uart2, blsp_i2c2, pbs2, NA,
+		 qdss_tracedata_b, NA, atest_gpsadc_dtest0_native, NA),
+	PINGROUP(8, blsp_spi3, blsp_uart3, pbs0, NA, NA, NA, NA, NA, NA),
+	PINGROUP(9, blsp_spi3, blsp_uart3, pbs1, pwr_modem_enabled_b, NA, NA,
+		 NA, NA, NA),
+	PINGROUP(10, blsp_spi3, blsp_uart3, blsp_i2c3, gcc_gp2_clk_b, NA, NA,
+		 NA, NA, NA),
+	PINGROUP(11, blsp_spi3, blsp_uart3, blsp_i2c3, gcc_gp3_clk_b, NA, NA,
+		 NA, NA, NA),
+	PINGROUP(12, blsp_spi4, blsp_uart4, sec_mi2s, pwr_nav_enabled_b, NA,
+		 NA, NA, NA, NA),
+	PINGROUP(13, blsp_spi4, blsp_uart4, sec_mi2s, pwr_crypto_enabled_b, NA,
+		 NA, NA, NA, NA),
+	PINGROUP(14, blsp_spi4, blsp_uart4, blsp_i2c4, NA, NA, NA, NA, NA, NA),
+	PINGROUP(15, blsp_spi4, blsp_uart4, blsp_i2c4, NA, NA, NA, NA, NA, NA),
+	PINGROUP(16, blsp_spi5, blsp_uart5, NA, NA, NA, NA, qdss_traceclk_a,
+		 NA, atest_bbrx1),
+	PINGROUP(17, blsp_spi5, blsp_uart5, m_voc, qdss_cti_trig_in_a0, NA,
+		 atest_bbrx0, NA, NA, NA),
+	PINGROUP(18, blsp_spi5, blsp_uart5, blsp_i2c5, qdss_tracectl_a, NA,
+		 atest_gpsadc_dtest1_native, NA, NA, NA),
+	PINGROUP(19, blsp_spi5, blsp_uart5, blsp_i2c5, qdss_tracedata_a, NA,
+		 NA, NA, NA, NA),
+	PINGROUP(20, blsp_spi6, blsp_uart6, NA, NA, NA, NA, NA, NA,
+		 qdss_tracectl_b),
+	PINGROUP(21, blsp_spi6, blsp_uart6, m_voc, NA, NA, NA, NA, NA,
+		 qdss_cti_trig_in_b0),
+	PINGROUP(22, blsp_spi6, blsp_uart6, blsp_i2c6, qdss_traceclk_b, NA,
+		 atest_wlan0, NA, NA, NA),
+	PINGROUP(23, blsp_spi6, blsp_uart6, blsp_i2c6, qdss_tracedata_b, NA,
+		 atest_wlan1, NA, NA, NA),
+	PINGROUP(24, mdp_vsync, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(25, mdp_vsync, pri_mi2s_mclk_a, sec_mi2s_mclk_a, NA, NA, NA,
+		 NA, NA, NA),
+	PINGROUP(26, cam_mclk, NA, NA, NA, NA, NA, qdss_tracedata_a, NA, NA),
+	PINGROUP(27, cam_mclk, NA, NA, NA, NA, NA, NA, NA, qdss_tracedata_a),
+	PINGROUP(28, cam_mclk, NA, NA, NA, NA, NA, qdss_tracedata_a, NA,
+		 atest_combodac_to_gpio_native),
+	PINGROUP(29, cci_i2c, pwr_modem_enabled_a, NA, NA, NA, NA, NA,
+		 qdss_tracedata_a, NA),
+	PINGROUP(30, cci_i2c, NA, NA, NA, NA, NA, NA, NA, qdss_tracedata_a),
+	PINGROUP(31, cci_i2c, NA, NA, NA, NA, NA, NA, NA, qdss_tracedata_a),
+	PINGROUP(32, cci_i2c, NA, NA, NA, NA, NA, NA, NA, qdss_tracedata_a),
+	PINGROUP(33, cci_timer0, NA, NA, NA, NA, NA, NA, NA, qdss_tracedata_a),
+	PINGROUP(34, cci_timer1, NA, NA, NA, NA, NA, NA, NA, qdss_tracedata_a),
+	PINGROUP(35, pwr_nav_enabled_a, NA, NA, NA, NA, NA, NA, NA,
+		 qdss_tracedata_a),
+	PINGROUP(36, pwr_crypto_enabled_a, NA, NA, NA, NA, NA, NA, NA,
+		 qdss_tracedata_a),
+	PINGROUP(37, NA, NA, NA, NA, NA, qdss_cti_trig_out_b1, NA, NA, NA),
+	PINGROUP(38, NA, qdss_tracedata_a, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(39, cci_async, NA, NA, NA, NA, NA, qdss_tracedata_a, NA,
+		 atest_combodac_to_gpio_native),
+	PINGROUP(40, NA, NA, NA, NA, qdss_tracedata_a, NA,
+		 atest_combodac_to_gpio_native, NA, NA),
+	PINGROUP(41, sd_write, NA, NA, NA, NA, NA, NA, NA,
+		 atest_combodac_to_gpio_native),
+	PINGROUP(42, gcc_gp1_clk_a, qdss_tracedata_b, NA,
+		 atest_combodac_to_gpio_native, NA, NA, NA, NA, NA),
+	PINGROUP(43, gcc_gp2_clk_a, qdss_tracedata_b, NA,
+		 atest_combodac_to_gpio_native, NA, NA, NA, NA, NA),
+	PINGROUP(44, gcc_gp3_clk_a, qdss_tracedata_b, NA,
+		 atest_combodac_to_gpio_native, NA, NA, NA, NA, NA),
+	PINGROUP(45, NA, NA, atest_combodac_to_gpio_native, NA, NA, NA, NA, NA,
+		 NA),
+	PINGROUP(46, NA, NA, atest_combodac_to_gpio_native, NA, NA, NA, NA, NA,
+		 NA),
+	PINGROUP(47, blsp6_spi, NA, qdss_tracedata_b, NA,
+		 atest_combodac_to_gpio_native, NA, NA, NA, NA),
+	PINGROUP(48, NA, qdss_cti_trig_in_b1, NA,
+		 atest_combodac_to_gpio_native, NA, NA, NA, NA, NA),
+	PINGROUP(49, uim_batt, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(50, qdss_tracedata_a, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(51, uim1_data, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(52, uim1_clk, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(53, uim1_reset, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(54, uim1_present, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(55, uim2_data, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(56, uim2_clk, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(57, uim2_reset, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(58, uim2_present, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(59, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(60, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(61, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(62, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(63, atest_char3, dbg_out, bimc_dte0, NA, NA, NA, NA, NA, NA),
+	PINGROUP(64, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(65, bimc_dte0, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(66, sec_mi2s_mclk_b, pri_mi2s, NA, qdss_tracedata_b, NA, NA,
+		 NA, NA, NA),
+	PINGROUP(67, atest_char1, ebi_cdc, NA, atest_combodac_to_gpio_native,
+		 NA, NA, NA, NA, NA),
+	PINGROUP(68, atest_char0, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(69, audio_ref, cdc_pdm0, pri_mi2s_mclk_b, ebi_cdc, NA, NA, NA,
+		 NA, NA),
+	PINGROUP(70, lpass_slimbus, cdc_pdm0, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(71, lpass_slimbus0, cdc_pdm0, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(72, lpass_slimbus1, cdc_pdm0, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(73, cdc_pdm0, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(74, cdc_pdm0, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(75, wcss_bt, atest_char2, NA, ebi_ch0, NA, NA, NA, NA, NA),
+	PINGROUP(76, wcss_wlan2, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(77, wcss_wlan1, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(78, wcss_wlan0, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(79, wcss_wlan, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(80, wcss_wlan, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(81, wcss_fm, ext_lpass, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(82, wcss_fm, cri_trng, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(83, wcss_bt, cri_trng1, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(84, wcss_bt, cri_trng0, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(85, pri_mi2s, blsp_spi7, blsp_uart7, NA, NA, NA, NA, NA, NA),
+	PINGROUP(86, pri_mi2s, blsp_spi7, blsp_uart7, qdss_tracedata_b, NA, NA,
+		 NA, NA, NA),
+	PINGROUP(87, pri_mi2s_ws, blsp_spi7, blsp_uart7, blsp_i2c7,
+		 qdss_tracedata_b, gcc_tlmm, NA, NA, NA),
+	PINGROUP(88, pri_mi2s, blsp_spi7, blsp_uart7, blsp_i2c7, NA, NA, NA,
+		 NA, NA),
+	PINGROUP(89, dmic0_clk, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(90, dmic0_data, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(91, NA, NA, NA, NA, NA, qdss_cti_trig_in_a1, NA, NA, NA),
+	PINGROUP(92, NA, NA, NA, NA, NA, qdss_tracedata_b, NA, NA, NA),
+	PINGROUP(93, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(94, wsa_io, sec_mi2s, pri_mi2s, NA, NA, NA, NA, NA, NA),
+	PINGROUP(95, wsa_io, sec_mi2s, pri_mi2s, NA, NA, NA, NA, NA, NA),
+	PINGROUP(96, blsp_spi8, blsp_uart8, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(97, blsp_spi8, blsp_uart8, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(98, blsp_spi8, blsp_uart8, blsp_i2c8, gcc_plltest, NA, NA, NA,
+		 NA, NA),
+	PINGROUP(99, blsp_spi8, blsp_uart8, blsp_i2c8, gcc_plltest, NA, NA, NA,
+		 NA, NA),
+	PINGROUP(100, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(101, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(102, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(103, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(104, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(105, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(106, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(107, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(108, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(109, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(110, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(111, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(112, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(113, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(114, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(115, NA, NA, nav_pps_in_a, NA, atest_combodac_to_gpio_native,
+		 NA, NA, NA, NA),
+	PINGROUP(116, NA, pa_indicator, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(117, NA, modem_tsync, nav_tsync, nav_pps_in_b, nav_pps, NA,
+		 NA, NA, NA),
+	PINGROUP(118, NA, ebi_cdc, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(119, gsm0_tx, NA, ebi_cdc, NA, NA, NA, NA, NA, NA),
+	PINGROUP(120, NA, atest_char, ebi_cdc, NA, atest_tsens, NA, NA, NA, NA),
+	PINGROUP(121, NA, NA, NA, bimc_dte1, NA, NA, NA, NA, NA),
+	PINGROUP(122, NA, ssbi_wtr1, NA, NA, bimc_dte1, NA, NA, NA, NA),
+	PINGROUP(123, NA, ssbi_wtr1, ebi_cdc, NA, NA, NA, NA, NA, NA),
+	PINGROUP(124, coex_uart, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(125, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(126, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(127, coex_uart, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(128, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(129, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(130, blsp8_spi, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(131, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(132, qdss_cti_trig_out_a0, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(133, qdss_cti_trig_out_a1, NA, NA, NA, NA, NA, NA, NA, NA),
+	SDC_PINGROUP(sdc1_clk, 0x10a000, 13, 6),
+	SDC_PINGROUP(sdc1_cmd, 0x10a000, 11, 3),
+	SDC_PINGROUP(sdc1_data, 0x10a000, 9, 0),
+	SDC_PINGROUP(sdc1_rclk, 0x10a000, 15, 0),
+	SDC_PINGROUP(sdc2_clk, 0x109000, 14, 6),
+	SDC_PINGROUP(sdc2_cmd, 0x109000, 11, 3),
+	SDC_PINGROUP(sdc2_data, 0x109000, 9, 0),
+	SDC_PINGROUP(qdsd_clk, 0x19c000, 3, 0),
+	SDC_PINGROUP(qdsd_cmd, 0x19c000, 8, 5),
+	SDC_PINGROUP(qdsd_data0, 0x19c000, 13, 10),
+	SDC_PINGROUP(qdsd_data1, 0x19c000, 18, 15),
+	SDC_PINGROUP(qdsd_data2, 0x19c000, 23, 20),
+	SDC_PINGROUP(qdsd_data3, 0x19c000, 28, 25),
+};
+
+#define NUM_GPIO_PINGROUPS	134
+
+static const struct msm_pinctrl_soc_data msm8917_pinctrl = {
+	.pins = msm8917_pins,
+	.npins = ARRAY_SIZE(msm8917_pins),
+	.functions = msm8917_functions,
+	.nfunctions = ARRAY_SIZE(msm8917_functions),
+	.groups = msm8917_groups,
+	.ngroups = ARRAY_SIZE(msm8917_groups),
+	.ngpios = NUM_GPIO_PINGROUPS,
+};
+
+static int msm8917_pinctrl_probe(struct platform_device *pdev)
+{
+	return msm_pinctrl_probe(pdev, &msm8917_pinctrl);
+}
+
+static const struct of_device_id msm8917_pinctrl_of_match[] = {
+	{ .compatible = "qcom,msm8917-pinctrl", },
+	{ },
+};
+
+static struct platform_driver msm8917_pinctrl_driver = {
+	.driver = {
+		.name = "msm8917-pinctrl",
+		.of_match_table = msm8917_pinctrl_of_match,
+	},
+	.probe = msm8917_pinctrl_probe,
+	.remove_new = msm_pinctrl_remove,
+};
+
+static int __init msm8917_pinctrl_init(void)
+{
+	return platform_driver_register(&msm8917_pinctrl_driver);
+}
+arch_initcall(msm8917_pinctrl_init);
+
+static void __exit msm8917_pinctrl_exit(void)
+{
+	platform_driver_unregister(&msm8917_pinctrl_driver);
+}
+module_exit(msm8917_pinctrl_exit);
+
+MODULE_DESCRIPTION("Qualcomm msm8917 pinctrl driver");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(of, msm8917_pinctrl_of_match);

-- 
2.47.0

[PATCH RFC 08/14] dt-bindings: mfd: qcom,tcsr: Add compatible for MSM8917

[Barnabás Czémán]

Document the qcom,msm8917-tcsr compatible.

Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
---
 Documentation/devicetree/bindings/mfd/qcom,tcsr.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/mfd/qcom,tcsr.yaml b/Documentation/devicetree/bindings/mfd/qcom,tcsr.yaml
index c4fcf501f502724b5ca36bc4a26f77a00104ac48..79add913e35c848363941a8634a361c45d296392 100644
--- a/Documentation/devicetree/bindings/mfd/qcom,tcsr.yaml
+++ b/Documentation/devicetree/bindings/mfd/qcom,tcsr.yaml
@@ -50,6 +50,7 @@ properties:
           - qcom,tcsr-msm8226
           - qcom,tcsr-msm8660
           - qcom,tcsr-msm8916
+          - qcom,tcsr-msm8917
           - qcom,tcsr-msm8953
           - qcom,tcsr-msm8960
           - qcom,tcsr-msm8974

-- 
2.47.0

[PATCH RFC 09/14] dt-bindings: thermal: tsens: Add MSM8917 compatible

[Barnabás Czémán]

Document the compatible string for tsens found in MSM8917.

Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
---
 Documentation/devicetree/bindings/thermal/qcom-tsens.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/thermal/qcom-tsens.yaml b/Documentation/devicetree/bindings/thermal/qcom-tsens.yaml
index a12fddc8195500a0e7bdd51952a558890b35935c..9add4fdc21fa307cbe9be6dde30369777f1ef91c 100644
--- a/Documentation/devicetree/bindings/thermal/qcom-tsens.yaml
+++ b/Documentation/devicetree/bindings/thermal/qcom-tsens.yaml
@@ -39,6 +39,7 @@ properties:
       - description: v1 of TSENS
         items:
           - enum:
+              - qcom,msm8917-tsens
               - qcom,msm8956-tsens
               - qcom,msm8976-tsens
               - qcom,qcs404-tsens

-- 
2.47.0

[PATCH RFC 10/14] dt-bindings: iommu: qcom,iommu: Add MSM8917 IOMMU to SMMUv1 compatibles

[Barnabás Czémán]

Add MSM8917 compatible string with "qcom,msm-iommu-v1" as fallback
for the MSM8917 IOMMU which is compatible with Qualcomm's secure
fw "SMMU v1" implementation.

Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
---
 Documentation/devicetree/bindings/iommu/qcom,iommu.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/iommu/qcom,iommu.yaml b/Documentation/devicetree/bindings/iommu/qcom,iommu.yaml
index f8cebc9e8cd9d46b449cd297153dbebe5c84bf3f..5ae9a628261fd251c1e991a70662c6d37ef2c4e3 100644
--- a/Documentation/devicetree/bindings/iommu/qcom,iommu.yaml
+++ b/Documentation/devicetree/bindings/iommu/qcom,iommu.yaml
@@ -21,6 +21,7 @@ properties:
       - items:
           - enum:
               - qcom,msm8916-iommu
+              - qcom,msm8917-iommu
               - qcom,msm8953-iommu
           - const: qcom,msm-iommu-v1
       - items:

-- 
2.47.0

[PATCH RFC 11/14] dt-bindings: nvmem: Add compatible for MS8917

[Barnabás Czémán]

Document the QFPROM block found on MSM8917.

Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
---
 Documentation/devicetree/bindings/nvmem/qcom,qfprom.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/nvmem/qcom,qfprom.yaml b/Documentation/devicetree/bindings/nvmem/qcom,qfprom.yaml
index 80845c722ae46611c722effeaaf014a0caf76e4a..4d81f98ed37a3a12f01d444dbfa77badcc09c22d 100644
--- a/Documentation/devicetree/bindings/nvmem/qcom,qfprom.yaml
+++ b/Documentation/devicetree/bindings/nvmem/qcom,qfprom.yaml
@@ -26,6 +26,7 @@ properties:
           - qcom,ipq9574-qfprom
           - qcom,msm8226-qfprom
           - qcom,msm8916-qfprom
+          - qcom,msm8917-qfprom
           - qcom,msm8974-qfprom
           - qcom,msm8976-qfprom
           - qcom,msm8996-qfprom

-- 
2.47.0

[PATCH RFC 12/14] arm64: dts: qcom: Add initial support for MSM8917

[Barnabás Czémán]

From: Otto Pflüger <otto.pflueger@abscue.de>

Add initial support for MSM8917 SoC.

Signed-off-by: Otto Pflüger <otto.pflueger@abscue.de>
[reword commit, rebase, fix schema errors]
Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
---
 arch/arm64/boot/dts/qcom/msm8917-pins.dtsi |  344 ++++++
 arch/arm64/boot/dts/qcom/msm8917.dtsi      | 1557 ++++++++++++++++++++++++++++
 arch/arm64/boot/dts/qcom/pm8916.dtsi       |    9 +-
 3 files changed, 1909 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/msm8917-pins.dtsi b/arch/arm64/boot/dts/qcom/msm8917-pins.dtsi
new file mode 100644
index 0000000000000000000000000000000000000000..f283ffd59b8aca8e510ef95d5526af9592a1c036
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8917-pins.dtsi
@@ -0,0 +1,344 @@
+// SPDX-License-Identifier: GPL-2.0
+&tlmm {
+	blsp1_uart1_default: blsp1-uart1-default-state {
+		pins = "gpio0", "gpio1", "gpio2", "gpio3";
+		function = "blsp_uart1";
+
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	blsp1_uart1_sleep: blsp1-uart1-sleep-state {
+		pins = "gpio0", "gpio1", "gpio2", "gpio3";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	blsp1_uart2_default: blsp1-uart2-default-state {
+		pins = "gpio4", "gpio5";
+		function = "blsp_uart2";
+
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	blsp1_uart2_sleep: blsp1-uart2-sleep-state {
+		pins = "gpio4", "gpio5";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	blsp2_uart1_default: blsp2-uart1-default-state {
+		pins = "gpio16", "gpio17", "gpio18", "gpio19";
+		function = "blsp_uart5";
+
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	blsp2_uart1_sleep: blsp2-uart1-sleep-state {
+		pins = "gpio16", "gpio17", "gpio18", "gpio19";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	blsp2_uart2_default: blsp2-uart2-default-state {
+		pins = "gpio20", "gpio21", "gpio22", "gpio23";
+		function = "blsp_uart5";
+
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	blsp2_uart2_sleep: blsp2-uart2-sleep-state {
+		pins = "gpio20", "gpio21", "gpio22", "gpio23";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	i2c2_default: i2c2-default-state {
+		pins = "gpio6", "gpio7";
+		function = "blsp_i2c2";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	i2c2_sleep: i2c2-sleep-state {
+		pins = "gpio6", "gpio7";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	i2c3_default: i2c3-default-state {
+		pins = "gpio10", "gpio11";
+		function = "blsp_i2c3";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	i2c3_sleep: i2c3-sleep-state {
+		pins = "gpio10", "gpio11";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	i2c4_default: i2c4-default-state {
+		pins = "gpio14", "gpio15";
+		function = "blsp_i2c4";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	i2c4_sleep: i2c4-sleep-state {
+		pins = "gpio14", "gpio15";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	i2c5_default: i2c5-default-state {
+		pins = "gpio18", "gpio19";
+		function = "blsp_i2c5";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	i2c5_sleep: i2c5-sleep-state {
+		pins = "gpio18", "gpio19";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	i2c6_default: i2c6-default-state {
+		pins = "gpio22", "gpio23";
+		function = "blsp_i2c6";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	i2c6_sleep: i2c6-sleep-state {
+		pins = "gpio22", "gpio23";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	spi3_default: spi3-default-state {
+		pins = "gpio8", "gpio9", "gpio10", "gpio11";
+		function = "blsp_spi3";
+
+		drive-strength = <12>;
+		bias-disable;
+	};
+
+	spi3_sleep: spi3-sleep-state {
+		pins = "gpio8", "gpio9", "gpio10", "gpio11";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	spi6_default: spi6-default-state {
+		pins = "gpio20", "gpio21", "gpio22", "gpio23";
+		function = "blsp_spi6";
+
+		drive-strength = <12>;
+		bias-disable;
+	};
+
+	spi6_sleep: spi6-sleep-state {
+		pins = "gpio20", "gpio21", "gpio22", "gpio23";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	sdc1_clk_on: sdc1-clk-on-state {
+		pins = "sdc1_clk";
+		bias-disable;
+		drive-strength = <16>;
+	};
+
+	sdc1_clk_off: sdc1-clk-off-state {
+		pins = "sdc1_clk";
+		bias-disable;
+		drive-strength = <2>;
+	};
+
+	sdc1_cmd_on: sdc1-cmd-on-state {
+		pins = "sdc1_cmd";
+		bias-disable;
+		drive-strength = <10>;
+	};
+
+	sdc1_cmd_off: sdc1-cmd-off-state {
+		pins = "sdc1_cmd";
+		bias-disable;
+		drive-strength = <2>;
+	};
+
+	sdc1_data_on: sdc1-data-on-state {
+		pins = "sdc1_data";
+		bias-pull-up;
+		drive-strength = <10>;
+	};
+
+	sdc1_data_off: sdc1-data-off-state {
+		pins = "sdc1_data";
+		bias-pull-up;
+		drive-strength = <2>;
+	};
+
+	sdc1_rclk_on: sdc1-rclk-on-state {
+		pins = "sdc1_rclk";
+		bias-pull-down;
+	};
+
+	sdc1_rclk_off: sdc1-rclk-off-state {
+		pins = "sdc1_rclk";
+		bias-pull-down;
+	};
+
+	sdc2_clk_on: sdc2-clk-on-state {
+		pins = "sdc2_clk";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	sdc2_clk_off: sdc2-clk-off-state {
+		pins = "sdc2_clk";
+		bias-disable;
+		drive-strength = <2>;
+	};
+
+	sdc2_cmd_on: sdc2-cmd-on-state {
+		pins = "sdc2_cmd";
+		bias-pull-up;
+		drive-strength = <10>;
+	};
+
+	sdc2_cmd_off: sdc2-cmd-off-state {
+		pins = "sdc2_cmd";
+		bias-pull-up;
+		drive-strength = <2>;
+	};
+
+	sdc2_data_on: sdc2-data-on-state {
+		pins = "sdc2_data";
+		bias-pull-up;
+		drive-strength = <10>;
+	};
+
+	sdc2_data_off: sdc2-data-off-state {
+		pins = "sdc2_data";
+		bias-pull-up;
+		drive-strength = <2>;
+	};
+
+	sdc2_cd_on: cd-on-state {
+		pins = "gpio67";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+
+	sdc2_cd_off: cd-off-state {
+		pins = "gpio67";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	wcnss_pin_a: wcnss-active-state {
+		wcss-wlan2-pins {
+			pins = "gpio76";
+			function = "wcss_wlan2";
+			drive-strength = <6>;
+			bias-pull-up;
+
+		};
+
+		wcss-wlan1-pins {
+			pins = "gpio77";
+			function = "wcss_wlan1";
+			drive-strength = <6>;
+			bias-pull-up;
+
+		};
+
+		wcss-wlan0-pins {
+			pins = "gpio78";
+			function = "wcss_wlan0";
+			drive-strength = <6>;
+			bias-pull-up;
+
+		};
+
+		wcss-wlan-pins {
+			pins = "gpio79", "gpio80";
+			function = "wcss_wlan";
+			drive-strength = <6>;
+			bias-pull-up;
+
+		};
+	};
+
+	cci0_default: cci0-default-state {
+		pins = "gpio29", "gpio30";
+		function = "cci_i2c";
+
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	cci1_default: cci1-default-state {
+		pins = "gpio31", "gpio32";
+		function = "cci_i2c";
+
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	cdc_pdm_lines_act: pdm-lines-on-state {
+		pins = "gpio69", "gpio70", "gpio71", "gpio72",
+		       "gpio73", "gpio74";
+		function = "cdc_pdm0";
+
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	cdc_pdm_lines_sus: pdm-lines-off-state {
+		pins = "gpio69", "gpio70", "gpio71", "gpio72",
+		       "gpio73", "gpio74";
+		function = "cdc_pdm0";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8917.dtsi b/arch/arm64/boot/dts/qcom/msm8917.dtsi
new file mode 100644
index 0000000000000000000000000000000000000000..e5f580c6ec28ad6442b31a0e1ee256c376c5438d
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8917.dtsi
@@ -0,0 +1,1557 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <dt-bindings/clock/qcom,gcc-msm8917.h>
+#include <dt-bindings/clock/qcom,rpmcc.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
+#include <dt-bindings/soc/qcom,apr.h>
+#include <dt-bindings/sound/qcom,q6dsp-lpass-ports.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+	interrupt-parent = <&intc>;
+
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	aliases {
+		mmc0 = &sdhc_1; /* SDC1 eMMC slot */
+		mmc1 = &sdhc_2; /* SDC2 SD card slot */
+	};
+
+	chosen { };
+
+	memory@80000000 {
+		device_type = "memory";
+		/* We expect the bootloader to fill in the reg */
+		reg = <0 0x80000000 0 0>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		reserved@85b00000 {
+			reg = <0x0 0x85b00000 0x0 0x800000>;
+			no-map;
+		};
+
+		smem@86300000 {
+			compatible = "qcom,smem";
+			reg = <0x0 0x86300000 0x0 0x100000>;
+			no-map;
+
+			hwlocks = <&tcsr_mutex 3>;
+			qcom,rpm-msg-ram = <&rpm_msg_ram>;
+		};
+
+		reserved@86400000 {
+			reg = <0x0 0x86400000 0x0 0x400000>;
+			no-map;
+		};
+
+		mpss_mem: mpss@86800000 {
+			/*
+			 * The memory region for the mpss firmware is generally
+			 * relocatable and could be allocated dynamically.
+			 * However, many firmware versions tend to fail when
+			 * loaded to some special addresses, so it is hard to
+			 * define reliable alloc-ranges.
+			 *
+			 * alignment = <0x0 0x400000>;
+			 * alloc-ranges = <0x0 0x86800000 0x0 0x8000000>;
+			 */
+			reg = <0x0 0x86800000 0x0 0>; /* size is device-specific */
+			no-map;
+			status = "disabled";
+		};
+
+		adsp_mem: adsp {
+			size = <0x0 0x1100000>;
+			alignment = <0x0 0x100000>;
+			alloc-ranges = <0x0 0x86800000 0x0 0x8000000>;
+			no-map;
+			status = "disabled";
+		};
+
+		wcnss_mem: wcnss {
+			size = <0x0 0x700000>;
+			alignment = <0x0 0x100000>;
+			alloc-ranges = <0x0 0x86800000 0x0 0x8000000>;
+			no-map;
+			status = "disabled";
+		};
+
+		venus_mem: venus {
+			size = <0x0 0x400000>;
+			alignment = <0x0 0x100000>;
+			alloc-ranges = <0x0 0x86800000 0x0 0x8000000>;
+			no-map;
+			status = "disabled";
+		};
+
+		mba_mem: mba {
+			size = <0x0 0x100000>;
+			alignment = <0x0 0x100000>;
+			alloc-ranges = <0x0 0x86800000 0x0 0x8000000>;
+			no-map;
+			status = "disabled";
+		};
+
+		rmtfs@92100000 {
+			compatible = "qcom,rmtfs-mem";
+			reg = <0x0 0x92100000 0x0 0x180000>;
+			no-map;
+
+			qcom,client-id = <1>;
+		};
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		CPU0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x100>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+			clocks = <&apcs>;
+			operating-points-v2 = <&cpu_opp_table>;
+			#cooling-cells = <2>;
+			power-domains = <&CPU_PD0>;
+			power-domain-names = "psci";
+		};
+
+		CPU1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x101>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+			clocks = <&apcs>;
+			operating-points-v2 = <&cpu_opp_table>;
+			#cooling-cells = <2>;
+			power-domains = <&CPU_PD1>;
+			power-domain-names = "psci";
+		};
+
+		CPU2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x102>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+			clocks = <&apcs>;
+			operating-points-v2 = <&cpu_opp_table>;
+			#cooling-cells = <2>;
+			power-domains = <&CPU_PD2>;
+			power-domain-names = "psci";
+		};
+
+		CPU3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x103>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+			clocks = <&apcs>;
+			operating-points-v2 = <&cpu_opp_table>;
+			#cooling-cells = <2>;
+			power-domains = <&CPU_PD3>;
+			power-domain-names = "psci";
+		};
+
+		L2_0: l2-cache {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+		};
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&CPU0>;
+				};
+
+				core1 {
+					cpu = <&CPU1>;
+				};
+
+				core2 {
+					cpu = <&CPU2>;
+				};
+
+				core3 {
+					cpu = <&CPU3>;
+				};
+			};
+		};
+
+		idle-states {
+			entry-method = "psci";
+
+			CPU_SLEEP_0: cpu-sleep-0 {
+				compatible = "arm,idle-state";
+				idle-state-name = "standalone-power-collapse";
+				arm,psci-suspend-param = <0x40000003>;
+				entry-latency-us = <125>;
+				exit-latency-us = <180>;
+				min-residency-us = <595>;
+				local-timer-stop;
+			};
+		};
+
+		domain-idle-states {
+			CLUSTER_PWRDN: cluster-gdhs {
+				compatible = "domain-idle-state";
+				arm,psci-suspend-param = <0x41000043>;
+				entry-latency-us = <240>;
+				exit-latency-us = <280>;
+				min-residency-us = <806>;
+			};
+
+			CLUSTER_RET: cluster-retention {
+				compatible = "domain-idle-state";
+				arm,psci-suspend-param = <0x41000023>;
+				entry-latency-us = <700>;
+				exit-latency-us = <650>;
+				min-residency-us = <1972>;
+			};
+
+			CLUSTER_PC: cluster-power-collapse {
+				compatible = "domain-idle-state";
+				arm,psci-suspend-param = <0x41000053>;
+				entry-latency-us = <700>;
+				exit-latency-us = <1000>;
+				min-residency-us = <6500>;
+			};
+		};
+	};
+
+	cpu_opp_table: opp-table-cpu {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-960000000 {
+			opp-hz = /bits/ 64 <960000000>;
+		};
+
+		opp-1094400000 {
+			opp-hz = /bits/ 64 <1094400000>;
+		};
+
+		opp-1248000000 {
+			opp-hz = /bits/ 64 <1248000000>;
+		};
+
+		opp-1401600000 {
+			opp-hz = /bits/ 64 <1401600000>;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+		clock-frequency = <19200000>;
+	};
+
+	clocks {
+		xo_board: xo-board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <19200000>;
+			clock-output-names = "xo";
+		};
+
+		sleep_clk: sleep-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+			clock-output-names = "sleep_clk";
+		};
+	};
+
+	firmware {
+		scm: scm {
+			compatible = "qcom,scm-msm8916", "qcom,scm";
+			clocks = <&gcc GCC_CRYPTO_CLK>,
+				 <&gcc GCC_CRYPTO_AXI_CLK>,
+				 <&gcc GCC_CRYPTO_AHB_CLK>;
+			clock-names = "core", "bus", "iface";
+			#reset-cells = <1>;
+
+			qcom,dload-mode = <&tcsr 0x6100>;
+		};
+	};
+
+	pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+
+		CPU_PD0: power-domain-cpu0 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&CPU_SLEEP_0>;
+		};
+
+		CPU_PD1: power-domain-cpu1 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&CPU_SLEEP_0>;
+		};
+
+		CPU_PD2: power-domain-cpu2 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&CPU_SLEEP_0>;
+		};
+
+		CPU_PD3: power-domain-cpu3 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&CPU_SLEEP_0>;
+		};
+
+		CLUSTER_PD: power-domain-cluster {
+			#power-domain-cells = <0>;
+			domain-idle-states = <&CLUSTER_PWRDN>, <&CLUSTER_RET>, <&CLUSTER_PC>;
+		};
+	};
+
+	rpm: remoteproc {
+		compatible = "qcom,msm8917-rpm-proc", "qcom,rpm-proc";
+
+		smd-edge {
+			interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
+			qcom,ipc = <&apcs 8 0>;
+			qcom,smd-edge = <15>;
+
+			rpm_requests: rpm-requests {
+				compatible = "qcom,rpm-msm8917", "qcom,smd-rpm";
+				qcom,smd-channels = "rpm_requests";
+
+				rpmcc: clock-controller {
+					compatible = "qcom,rpmcc-msm8917", "qcom,rpmcc";
+					#clock-cells = <1>;
+					clocks = <&xo_board>;
+					clock-names = "xo";
+				};
+
+				rpmpd: power-controller {
+					compatible = "qcom,msm8917-rpmpd";
+					#power-domain-cells = <1>;
+					operating-points-v2 = <&rpmpd_opp_table>;
+
+					rpmpd_opp_table: opp-table {
+						compatible = "operating-points-v2";
+
+						rpmpd_opp_ret: opp1 {
+							opp-level = <RPM_SMD_LEVEL_RETENTION>;
+						};
+
+						rpmpd_opp_ret_plus: opp2 {
+							opp-level = <RPM_SMD_LEVEL_RETENTION_PLUS>;
+						};
+
+						rpmpd_opp_min_svs: opp3 {
+							opp-level = <RPM_SMD_LEVEL_MIN_SVS>;
+						};
+
+						rpmpd_opp_low_svs: opp4 {
+							opp-level = <RPM_SMD_LEVEL_LOW_SVS>;
+						};
+
+						rpmpd_opp_svs: opp5 {
+							opp-level = <RPM_SMD_LEVEL_SVS>;
+						};
+
+						rpmpd_opp_svs_plus: opp6 {
+							opp-level = <RPM_SMD_LEVEL_SVS_PLUS>;
+						};
+
+						rpmpd_opp_nom: opp7 {
+							opp-level = <RPM_SMD_LEVEL_NOM>;
+						};
+
+						rpmpd_opp_nom_plus: opp8 {
+							opp-level = <RPM_SMD_LEVEL_NOM_PLUS>;
+						};
+
+						rpmpd_opp_turbo: opp9 {
+							opp-level = <RPM_SMD_LEVEL_TURBO>;
+						};
+					};
+				};
+			};
+		};
+	};
+
+	smp2p-adsp {
+		compatible = "qcom,smp2p";
+		qcom,smem = <443>, <429>;
+
+		interrupts = <GIC_SPI 291 IRQ_TYPE_EDGE_RISING>;
+
+		mboxes = <&apcs 10>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <2>;
+
+		adsp_smp2p_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+
+			#qcom,smem-state-cells = <1>;
+		};
+
+		adsp_smp2p_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	smp2p-modem {
+		compatible = "qcom,smp2p";
+		qcom,smem = <435>, <428>;
+
+		interrupts = <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>;
+
+		qcom,ipc = <&apcs 8 14>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <1>;
+
+		modem_smp2p_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+
+			#qcom,smem-state-cells = <1>;
+		};
+
+		modem_smp2p_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	smp2p-wcnss {
+		compatible = "qcom,smp2p";
+		qcom,smem = <451>, <431>;
+
+		interrupts = <GIC_SPI 143 IRQ_TYPE_EDGE_RISING>;
+
+		qcom,ipc = <&apcs 8 18>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <4>;
+
+		wcnss_smp2p_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+
+			#qcom,smem-state-cells = <1>;
+		};
+
+		wcnss_smp2p_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	smsm {
+		compatible = "qcom,smsm";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		qcom,ipc-1 = <&apcs 8 13>;
+		qcom,ipc-3 = <&apcs 8 19>;
+
+		apps_smsm: apps@0 {
+			reg = <0>;
+
+			#qcom,smem-state-cells = <1>;
+		};
+
+		hexagon_smsm: hexagon@1 {
+			reg = <1>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		wcnss_smsm: wcnss@6 {
+			reg = <6>;
+			interrupts = <GIC_SPI 144 IRQ_TYPE_EDGE_RISING>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	soc: soc@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0 0 0xffffffff>;
+		compatible = "simple-bus";
+
+		rng@22000 {
+			compatible = "qcom,prng";
+			reg = <0xe3000 0x1000>;
+			clocks = <&gcc GCC_PRNG_AHB_CLK>;
+			clock-names = "core";
+		};
+
+		restart@4ab000 {
+			compatible = "qcom,pshold";
+			reg = <0x004ab000 0x4>;
+		};
+
+		qfprom: qfprom@a4000 {
+			compatible = "qcom,msm8917-qfprom", "qcom,qfprom";
+			reg = <0x000a4000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			tsens_caldata: caldata@d0 {
+				reg = <0x01d8 0x14>;
+			};
+		};
+
+		rpm_msg_ram: sram@60000 {
+			compatible = "qcom,rpm-msg-ram";
+			reg = <0x00060000 0x8000>;
+		};
+
+		tsens: thermal-sensor@4a9000 {
+			compatible = "qcom,msm8917-tsens", "qcom,tsens-v1";
+			reg = <0x004a9000 0x1000>,
+			      <0x004a8000 0x1000>;
+			nvmem-cells = <&tsens_caldata>;
+			nvmem-cell-names = "calib";
+			#qcom,sensors = <10>;
+			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow";
+			#thermal-sensor-cells = <1>;
+		};
+
+		tlmm: pinctrl@1000000 {
+			compatible = "qcom,msm8917-pinctrl";
+			reg = <0x01000000 0x300000>;
+			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			gpio-ranges = <&tlmm 0 0 134>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gcc: clock-controller@1800000 {
+			compatible = "qcom,gcc-msm8917";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+			reg = <0x01800000 0x80000>;
+			clocks = <&xo_board>,
+				 <&sleep_clk>,
+				 <&mdss_dsi0_phy 1>,
+				 <&mdss_dsi0_phy 0>;
+			clock-names = "xo",
+				      "sleep_clk",
+				      "dsi0pll",
+				      "dsi0pllbyte";
+		};
+
+		tcsr_mutex: hwlock@1905000 {
+			compatible = "qcom,tcsr-mutex";
+			reg = <0x01905000 0x20000>;
+			#hwlock-cells = <1>;
+		};
+
+		tcsr: syscon@1937000 {
+			compatible = "qcom,tcsr-msm8917", "syscon";
+			reg = <0x01937000 0x30000>;
+		};
+
+		apps_iommu: iommu@1e00000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			#iommu-cells = <1>;
+			compatible = "qcom,msm8917-iommu", "qcom,msm-iommu-v1";
+			ranges = <0 0x01e20000 0x20000>;
+
+			clocks = <&gcc GCC_SMMU_CFG_CLK>,
+				 <&gcc GCC_APSS_TCU_CLK>;
+			clock-names = "iface", "bus";
+
+			qcom,iommu-secure-id = <17>;
+
+			/* VFE */
+			iommu-ctx@14000 {
+				compatible = "qcom,msm-iommu-v1-ns";
+				reg = <0x00014000 0x1000>;
+				interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			/* MDP_0 */
+			iommu-ctx@15000 {
+				compatible = "qcom,msm-iommu-v1-ns";
+				reg = <0x00015000 0x1000>;
+				interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			/* VENUS_NS */
+			iommu-ctx@16000 {
+				compatible = "qcom,msm-iommu-v1-ns";
+				reg = <0x00016000 0x1000>;
+				interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+			};
+		};
+
+		gpu_iommu: iommu@1f00000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			#iommu-cells = <1>;
+
+			compatible = "qcom,msm8917-iommu", "qcom,msm-iommu-v1";
+
+			ranges = <0 0x01f08000 0x10000>;
+			clocks = <&gcc GCC_SMMU_CFG_CLK>,
+				 <&gcc GCC_GFX_TCU_CLK>;
+			clock-names = "iface", "bus";
+			qcom,iommu-secure-id = <18>;
+
+			iommu-ctx@0 {
+				compatible = "qcom,msm-iommu-v2-ns";
+				reg = <0x0000 0x1000>;
+				interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>;
+			};
+		};
+
+		mdss: display-subsystem@1a00000 {
+			compatible = "qcom,mdss";
+			reg = <0x01a00000 0x1000>,
+			      <0x01ab0000 0x1040>;
+			reg-names = "mdss_phys", "vbif_phys";
+
+			power-domains = <&gcc MDSS_GDSC>;
+
+			clocks = <&gcc GCC_MDSS_AHB_CLK>,
+				 <&gcc GCC_MDSS_AXI_CLK>,
+				 <&gcc GCC_MDSS_VSYNC_CLK>;
+			clock-names = "iface",
+				      "bus",
+				      "vsync";
+
+			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			status = "disabled";
+
+			mdp: display-controller@1a01000 {
+				compatible = "qcom,msm8917-mdp5", "qcom,mdp5";
+				reg = <0x01a01000 0x89000>;
+				reg-names = "mdp_phys";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <0>;
+
+				power-domains = <&gcc MDSS_GDSC>;
+
+				clocks = <&gcc GCC_MDSS_AHB_CLK>,
+					 <&gcc GCC_MDSS_AXI_CLK>,
+					 <&gcc GCC_MDSS_MDP_CLK>,
+					 <&gcc GCC_MDSS_VSYNC_CLK>;
+				clock-names = "iface",
+					      "bus",
+					      "core",
+					      "vsync";
+
+				iommus = <&apps_iommu 0x15>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						mdp5_intf1_out: endpoint {
+							remote-endpoint = <&mdss_dsi0_in>;
+						};
+					};
+				};
+			};
+
+			mdss_dsi0: dsi@1a94000 {
+				compatible = "qcom,mdss-dsi-ctrl";
+				reg = <0x01a94000 0x300>;
+				reg-names = "dsi_ctrl";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <4>;
+
+				assigned-clocks = <&gcc BYTE0_CLK_SRC>,
+						  <&gcc PCLK0_CLK_SRC>;
+				assigned-clock-parents = <&mdss_dsi0_phy 0>,
+							 <&mdss_dsi0_phy 1>;
+
+				clocks = <&gcc GCC_MDSS_MDP_CLK>,
+					 <&gcc GCC_MDSS_AHB_CLK>,
+					 <&gcc GCC_MDSS_AXI_CLK>,
+					 <&gcc GCC_MDSS_BYTE0_CLK>,
+					 <&gcc GCC_MDSS_PCLK0_CLK>,
+					 <&gcc GCC_MDSS_ESC0_CLK>;
+				clock-names = "mdp_core",
+					      "iface",
+					      "bus",
+					      "byte",
+					      "pixel",
+					      "core";
+				phys = <&mdss_dsi0_phy>;
+
+				operating-points-v2 = <&mdss_dsi0_opp_table>;
+				power-domains = <&rpmpd MSM8917_VDDCX>;
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						mdss_dsi0_in: endpoint {
+							remote-endpoint = <&mdp5_intf1_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						mdss_dsi0_out: endpoint {
+						};
+					};
+				};
+
+				mdss_dsi0_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					opp-125000000 {
+						opp-hz = /bits/ 64 <125000000>;
+						required-opps = <&rpmpd_opp_svs>;
+					};
+
+					opp-187500000 {
+						opp-hz = /bits/ 64 <187500000>;
+						required-opps = <&rpmpd_opp_nom>;
+					};
+				};
+			};
+
+			mdss_dsi0_phy: phy@1a94400 {
+				compatible = "qcom,dsi-phy-28nm-8937";
+				reg = <0x01a94a00 0xd4>,
+				      <0x01a94400 0x280>,
+				      <0x01a94b80 0x30>;
+				reg-names = "dsi_pll",
+					    "dsi_phy",
+					    "dsi_phy_regulator";
+
+				#clock-cells = <1>;
+				#phy-cells = <0>;
+
+				clocks = <&gcc GCC_MDSS_AHB_CLK>,
+					 <&xo_board>;
+				clock-names = "iface", "ref";
+			};
+		};
+
+		a53pll: clock@b016000 {
+			compatible = "qcom,msm8939-a53pll";
+			reg = <0x0b016000 0x40>;
+			clocks = <&xo_board>;
+			clock-names = "xo";
+			#clock-cells = <0>;
+			operating-points-v2 = <&pll_opp_table>;
+
+			pll_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-960000000 {
+					opp-hz = /bits/ 64 <960000000>;
+				};
+
+				opp-1094400000 {
+					opp-hz = /bits/ 64 <1094400000>;
+				};
+
+				opp-1248000000 {
+					opp-hz = /bits/ 64 <1248000000>;
+				};
+
+				opp-1401600000 {
+				      opp-hz = /bits/ 64 <1401600000>;
+				};
+			};
+		};
+
+		gpu: gpu@1c00000 {
+			compatible = "qcom,adreno-306.32", "qcom,adreno";
+			reg = <0x01c00000 0x20000>;
+			reg-names = "kgsl_3d0_reg_memory";
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "kgsl_3d0_irq";
+			clock-names = "core",
+				      "iface",
+				      "mem_iface",
+				      "alt_mem_iface",
+				      "gfx3d";
+			clocks = <&gcc GCC_OXILI_GFX3D_CLK>,
+				 <&gcc GCC_OXILI_AHB_CLK>,
+				 <&gcc GCC_BIMC_GFX_CLK>,
+				 <&gcc GCC_BIMC_GPU_CLK>,
+				 <&gcc GFX3D_CLK_SRC>;
+			power-domains = <&gcc OXILI_GX_GDSC>;
+			operating-points-v2 = <&gpu_opp_table>;
+			#cooling-cells = <2>;
+
+			iommus = <&gpu_iommu 0>;
+
+			status = "disabled";
+
+			gpu_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-598000000 {
+					opp-hz = /bits/ 64 <598000000>;
+				};
+
+				opp-523200000 {
+					opp-hz = /bits/ 64 <523200000>;
+				};
+
+				opp-484800000 {
+					opp-hz = /bits/ 64 <484800000>;
+				};
+
+				opp-400000000 {
+					opp-hz = /bits/ 64 <400000000>;
+				};
+
+				opp-270000000 {
+					opp-hz = /bits/ 64 <270000000>;
+				};
+
+				opp-19200000 {
+					opp-hz = /bits/ 64 <19200000>;
+				};
+			};
+		};
+
+		spmi_bus: spmi@200f000 {
+			compatible = "qcom,spmi-pmic-arb";
+			reg = <0x0200f000 0x001000>,
+			      <0x02400000 0x800000>,
+			      <0x02c00000 0x800000>,
+			      <0x03800000 0x200000>,
+			      <0x0200a000 0x002100>;
+			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
+			interrupt-names = "periph_irq";
+			interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,ee = <0>;
+			qcom,channel = <0>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			interrupt-controller;
+			#interrupt-cells = <4>;
+		};
+
+		bam_dmux_dma: dma-controller@4044000 {
+			compatible = "qcom,bam-v1.7.0";
+			reg = <0x04044000 0x19000>;
+			interrupts = <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+
+			num-channels = <6>;
+			qcom,num-ees = <1>;
+			qcom,powered-remotely;
+
+			status = "disabled";
+		};
+
+		apcs: mailbox@b011000 {
+			compatible = "qcom,msm8939-apcs-kpss-global", "syscon";
+			reg = <0x0b011000 0x1000>;
+			#mbox-cells = <1>;
+			clocks = <&a53pll>, <&gcc GPLL0_EARLY>, <&rpmcc RPM_SMD_XO_CLK_SRC>;
+			clock-names = "pll", "aux", "ref";
+			#clock-cells = <0>;
+		};
+
+		sdhc_1: mmc@7824900 {
+			compatible = "qcom,sdhci-msm-v4";
+			reg = <0x07824900 0x500>, <0x07824000 0x800>;
+			reg-names = "hc", "core";
+
+			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>,
+				 <&xo_board>;
+			clock-names = "iface", "core", "xo";
+			power-domains = <&rpmpd MSM8917_VDDCX>;
+			mmc-hs200-1_8v;
+			mmc-hs400-1_8v;
+			mmc-ddr-1_8v;
+			bus-width = <8>;
+			non-removable;
+			status = "disabled";
+		};
+
+		sdhc_2: mmc@7864900 {
+			compatible = "qcom,sdhci-msm-v4";
+			reg = <0x07864900 0x500>, <0x07864000 0x800>;
+			reg-names = "hc", "core";
+
+			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+				 <&gcc GCC_SDCC2_APPS_CLK>,
+				 <&xo_board>;
+			clock-names = "iface", "core", "xo";
+			power-domains = <&rpmpd MSM8917_VDDCX>;
+			bus-width = <4>;
+			status = "disabled";
+		};
+
+		blsp1_dma: dma-controller@7884000 {
+			compatible = "qcom,bam-v1.7.0";
+			reg = <0x07884000 0x1f000>;
+			interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "bam_clk";
+			qcom,controlled-remotely;
+			#dma-cells = <1>;
+			num-channels = <12>;
+			qcom,num-ees = <4>;
+			qcom,ee = <0>;
+		};
+
+		blsp2_dma: dma-controller@7ac4000 {
+			compatible = "qcom,bam-v1.7.0";
+			reg = <0x07ac4000 0x1d000>;
+			interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "bam_clk";
+			qcom,controlled-remotely;
+			#dma-cells = <1>;
+			num-channels = <10>;
+			qcom,num-ees = <4>;
+			qcom,ee = <0>;
+		};
+
+		blsp1_uart1: serial@78af000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0x078af000 0x200>;
+			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp1_dma 0>, <&blsp1_dma 1>;
+			dma-names = "tx", "rx";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp1_uart1_default>;
+			pinctrl-1 = <&blsp1_uart1_sleep>;
+			status = "disabled";
+		};
+
+		blsp1_uart2: serial@78b0000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0x078b0000 0x200>;
+			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp1_dma 2>, <&blsp1_dma 3>;
+			dma-names = "tx", "rx";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp1_uart2_default>;
+			pinctrl-1 = <&blsp1_uart2_sleep>;
+			status = "disabled";
+		};
+
+		blsp_i2c2: i2c@78b6000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x078b6000 0x600>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp1_dma 6>, <&blsp1_dma 7>;
+			dma-names = "tx", "rx";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c2_default>;
+			pinctrl-1 = <&i2c2_sleep>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp_i2c3: i2c@78b7000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x078b7000 0x600>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp1_dma 8>, <&blsp1_dma 9>;
+			dma-names = "tx", "rx";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c3_default>;
+			pinctrl-1 = <&i2c3_sleep>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp_spi3: spi@78b7000 {
+			compatible = "qcom,spi-qup-v2.2.1";
+			reg = <0x078b7000 0x600>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP3_SPI_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp1_dma 8>, <&blsp1_dma 9>;
+			dma-names = "tx", "rx";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&spi3_default>;
+			pinctrl-1 = <&spi3_sleep>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp_i2c4: i2c@78b8000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x078b8000 0x500>;
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp1_dma 10>, <&blsp1_dma 11>;
+			dma-names = "tx", "rx";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c4_default>;
+			pinctrl-1 = <&i2c4_sleep>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp_i2c5: i2c@7af5000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x07af5000 0x600>;
+			interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp2_dma 4>, <&blsp2_dma 5>;
+			dma-names = "tx", "rx";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c5_default>;
+			pinctrl-1 = <&i2c5_sleep>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp_spi6: spi@7af6000 {
+			compatible = "qcom,spi-qup-v2.2.1";
+			reg = <0x07af6000 0x600>;
+			interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP2_QUP2_SPI_APPS_CLK>,
+				 <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp2_dma 6>, <&blsp2_dma 7>;
+			dma-names = "tx", "rx";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&spi6_default>;
+			pinctrl-1 = <&spi6_sleep>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		usb_hs_phy: phy@6c000 {
+			compatible = "qcom,usb-hs-28nm-femtophy";
+			reg = <0x6c000 0x200>;
+			#phy-cells = <0>;
+			clocks = <&xo_board>,
+				 <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>,
+				 <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
+			clock-names = "ref", "ahb", "sleep";
+			resets = <&gcc GCC_QUSB2_PHY_BCR>,
+				 <&gcc GCC_USB2_HS_PHY_ONLY_BCR>;
+			reset-names = "phy", "por";
+			status = "disabled";
+		};
+
+		usb: usb@78db000 {
+			compatible = "qcom,ci-hdrc";
+			reg = <0x078db000 0x200>,
+			      <0x078db200 0x200>;
+			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_USB_HS_AHB_CLK>,
+				 <&gcc GCC_USB_HS_SYSTEM_CLK>;
+			clock-names = "iface", "core";
+			assigned-clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>;
+			assigned-clock-rates = <80000000>;
+			resets = <&gcc GCC_USB_HS_BCR>;
+			reset-names = "core";
+			phy_type = "ulpi";
+			dr_mode = "otg";
+			hnp-disable;
+			srp-disable;
+			adp-disable;
+			ahb-burst-config = <0>;
+			phy-names = "usb-phy";
+			phys = <&usb_hs_phy>;
+			status = "disabled";
+			#reset-cells = <1>;
+		};
+
+		pronto: wcnss: remoteproc@a21b000 {
+			compatible = "qcom,pronto-v3-pil", "qcom,pronto";
+			reg = <0x0a204000 0x2000>, <0x0a202000 0x1000>, <0x0a21b000 0x3000>;
+			reg-names = "ccu", "dxe", "pmu";
+
+			memory-region = <&wcnss_mem>;
+
+			interrupts-extended = <&intc GIC_SPI 149 IRQ_TYPE_EDGE_RISING>,
+					      <&wcnss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&wcnss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&wcnss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&wcnss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";
+
+			power-domains = <&rpmpd MSM8917_VDDCX>,
+					<&rpmpd MSM8917_VDDMX>;
+			power-domain-names = "cx", "mx";
+
+			qcom,smem-states = <&wcnss_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&wcnss_pin_a>;
+
+			status = "disabled";
+
+			wcnss_iris: iris {
+				clocks = <&rpmcc RPM_SMD_RF_CLK2>;
+				clock-names = "xo";
+			};
+
+			smd-edge {
+				interrupts = <GIC_SPI 142 IRQ_TYPE_EDGE_RISING>;
+
+				qcom,ipc = <&apcs 8 17>;
+				qcom,smd-edge = <6>;
+				qcom,remote-pid = <4>;
+
+				label = "pronto";
+
+				wcnss_ctrl: wcnss {
+					compatible = "qcom,wcnss";
+					qcom,smd-channels = "WCNSS_CTRL";
+
+					qcom,mmio = <&pronto>;
+
+					wcnss_bt: bluetooth {
+						compatible = "qcom,wcnss-bt";
+					};
+
+					wcnss_wifi: wifi {
+						compatible = "qcom,wcnss-wlan";
+
+						interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
+							     <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
+						interrupt-names = "tx", "rx";
+
+						qcom,smem-states = <&apps_smsm 10>, <&apps_smsm 9>;
+						qcom,smem-state-names = "tx-enable",
+									"tx-rings-empty";
+					};
+				};
+			};
+		};
+
+		intc: interrupt-controller@b000000 {
+			compatible = "qcom,msm-qgic2";
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			reg = <0x0b000000 0x1000>,
+			      <0x0b002000 0x1000>;
+		};
+
+		watchdog@b017000 {
+			compatible = "qcom,apss-wdt-qcs404", "qcom,kpss-wdt";
+			reg = <0x0b017000 0x1000>;
+			clocks = <&sleep_clk>;
+		};
+
+		timer@b120000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			compatible = "arm,armv7-timer-mem";
+			reg = <0x0b120000 0x1000>;
+			clock-frequency = <19200000>;
+
+			frame@b121000 {
+				frame-number = <0>;
+				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0b121000 0x1000>,
+				      <0x0b122000 0x1000>;
+			};
+
+			frame@b123000 {
+				frame-number = <1>;
+				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0b123000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@b124000 {
+				frame-number = <2>;
+				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0b124000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@b125000 {
+				frame-number = <3>;
+				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0b125000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@b126000 {
+				frame-number = <4>;
+				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0b126000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@b127000 {
+				frame-number = <5>;
+				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0b127000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@b128000 {
+				frame-number = <6>;
+				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0b128000 0x1000>;
+				status = "disabled";
+			};
+		};
+	};
+
+	thermal_zones: thermal-zones {
+		aoss-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 0>;
+
+			trips {
+				aoss_alert0: trip-point0 {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		mdm-core-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 1>;
+
+			trips {
+				mdm_core_alert0: trip-point0 {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		q6-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 2>;
+
+			trips {
+				q6_alert0: trip-point0 {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		camera-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 3>;
+
+			trips {
+				camera_alert0: trip-point0 {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		cpuss1-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 4>;
+
+			trips {
+				cpuss1_alert0: trip-point0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpuss1_alert1: trip-point1 {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+
+				cpuss1_crit: cpuss1-crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+			cooling-maps {
+				map0 {
+					trip = <&cpuss1_alert0>;
+					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		cpu0-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 5>;
+
+			trips {
+				cpu0_alert0: trip-point0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu0_alert1: trip-point1 {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+
+				cpu0_crit: cpu-crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+			cooling-maps {
+				map0 {
+					trip = <&cpu0_alert1>;
+					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		cpu1-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 6>;
+
+			trips {
+				cpu1_alert0: trip-point0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+
+				cpu1_alert1: trip-point1 {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu1_crit: cpu-crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+			cooling-maps {
+				map0 {
+					trip = <&cpu1_alert1>;
+					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		cpu2-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 7>;
+
+			trips {
+				cpu2_alert0: trip-point0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+
+				cpu2_alert1: trip-point1 {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu2_crit: cpu-crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+			cooling-maps {
+				map0 {
+					trip = <&cpu2_alert1>;
+					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		cpu3-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 8>;
+
+			trips {
+				cpu3_alert0: trip-point0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+
+				cpu3_alert1: trip-point1 {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu3_crit: cpu-crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+			cooling-maps {
+				map0 {
+					trip = <&cpu3_alert1>;
+					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		gpu-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 9>;
+
+			trips {
+				gpu_alert: trip-point0 {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				gpu_crit: gpu-crit {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&gpu_alert>;
+					cooling-device = <&gpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+};
+
+#include "msm8917-pins.dtsi"
diff --git a/arch/arm64/boot/dts/qcom/pm8916.dtsi b/arch/arm64/boot/dts/qcom/pm8916.dtsi
index f8e4829ff7f7de1f1f4f5da0f41020875d6c7e17..df0f679250ccb6c49a76288fad12f67b01fa6b61 100644
--- a/arch/arm64/boot/dts/qcom/pm8916.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm8916.dtsi
@@ -47,7 +47,7 @@ pon@800 {
 			mode-bootloader = <0x2>;
 			mode-recovery = <0x1>;
 
-			pwrkey {
+			pm8916_pwrkey: pwrkey {
 				compatible = "qcom,pm8941-pwrkey";
 				interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
 				debounce = <15625>;
@@ -210,6 +210,10 @@ pm8916_pwm: pwm {
 			status = "disabled";
 		};
 
+		pm8916_spmi_regulators: regulators {
+			compatible = "qcom,pm8916-regulators";
+		};
+
 		pm8916_vib: vibrator@c000 {
 			compatible = "qcom,pm8916-vib";
 			reg = <0xc000>;
@@ -219,6 +223,9 @@ pm8916_vib: vibrator@c000 {
 		pm8916_codec: audio-codec@f000 {
 			compatible = "qcom,pm8916-wcd-analog-codec";
 			reg = <0xf000>;
+			reg-names = "pmic-codec-core";
+			clocks = <&xo_board>;
+			clock-names = "mclk";
 			interrupt-parent = <&spmi_bus>;
 			interrupts = <0x1 0xf0 0x0 IRQ_TYPE_NONE>,
 				     <0x1 0xf0 0x1 IRQ_TYPE_NONE>,

-- 
2.47.0

[PATCH RFC 13/14] dt-bindings: arm: qcom: Add Xiaomi Redmi 5A

[Barnabás Czémán]

Document Xiaomi Remi 5A (riva).

Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
---
 Documentation/devicetree/bindings/arm/qcom.yaml | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 0d451082570edef9f2f80e2c7544a953eebe9edc..0d545a1744662df6d3c17771ae3cee80c89fb281 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -31,6 +31,7 @@ description: |
         mdm9615
         msm8226
         msm8916
+        msm8917
         msm8939
         msm8953
         msm8956
@@ -248,6 +249,11 @@ properties:
               - yiming,uz801-v3
           - const: qcom,msm8916
 
+      - items:
+          - enum:
+              - xiaomi,riva
+          - const: qcom,msm8917
+
       - items:
           - enum:
               - motorola,potter
@@ -1144,6 +1150,7 @@ allOf:
               - qcom,apq8026
               - qcom,apq8094
               - qcom,apq8096
+              - qcom,msm8917
               - qcom,msm8939
               - qcom,msm8953
               - qcom,msm8956

-- 
2.47.0

[PATCH RFC 14/14] arm64: dts: qcom: Add Xiaomi Redmi 5A

[Barnabás Czémán]

Add initial support for Xiaomi Redmi 5A (riva).

Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
---
 arch/arm64/boot/dts/qcom/Makefile                |   1 +
 arch/arm64/boot/dts/qcom/msm8917-xiaomi-riva.dts | 295 +++++++++++++++++++++++
 2 files changed, 296 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 065bb19481c16db2affd291826d420c83a89c52a..79add0e07d8a5f3362d70b0aaaaa9b8c48e31239 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -59,6 +59,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-wingtech-wt86518.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-wingtech-wt86528.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-wingtech-wt88047.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-yiming-uz801v3.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= msm8917-xiaomi-riva.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8929-wingtech-wt82918hd.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8939-huawei-kiwi.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8939-longcheer-l9100.dtb
diff --git a/arch/arm64/boot/dts/qcom/msm8917-xiaomi-riva.dts b/arch/arm64/boot/dts/qcom/msm8917-xiaomi-riva.dts
new file mode 100644
index 0000000000000000000000000000000000000000..7553f73603fc87797b0d424a2af6f2da65c90f5f
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8917-xiaomi-riva.dts
@@ -0,0 +1,295 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023, Barnabas Czeman
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/arm/qcom,ids.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/leds/common.h>
+#include "msm8917.dtsi"
+#include "pm8937.dtsi"
+
+/ {
+	model = "Xiaomi Redmi 5A (riva)";
+	compatible = "xiaomi,riva", "qcom,msm8917";
+	chassis-type = "handset";
+
+	qcom,msm-id = <QCOM_ID_MSM8917 0>;
+	qcom,board-id = <0x1000b 2>, <0x2000b 2>;
+
+	battery: battery {
+		compatible = "simple-battery";
+		charge-full-design-microamp-hours = <3000000>;
+		energy-full-design-microwatt-hours = <11500000>;
+		constant-charge-current-max-microamp = <1000000>;
+		constant-charge-voltage-max-microvolt = <4400000>;
+		precharge-current-microamp = <256000>;
+		charge-term-current-microamp = <60000>;
+		voltage-min-design-microvolt = <3400000>;
+	};
+
+	chosen {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		stdout-path = "framebuffer0";
+
+		framebuffer0: framebuffer@90001000 {
+			compatible = "simple-framebuffer";
+			reg = <0x0 0x90001000 0x0 (720 * 1280 * 3)>;
+			width = <720>;
+			height = <1280>;
+			stride = <(720 * 3)>;
+			format = "r8g8b8";
+
+			clocks = <&gcc GCC_MDSS_AHB_CLK>,
+				 <&gcc GCC_MDSS_AXI_CLK>,
+				 <&gcc GCC_MDSS_VSYNC_CLK>,
+				 <&gcc GCC_MDSS_MDP_CLK>,
+				 <&gcc GCC_MDSS_BYTE0_CLK>,
+				 <&gcc GCC_MDSS_PCLK0_CLK>,
+				 <&gcc GCC_MDSS_ESC0_CLK>;
+			power-domains = <&gcc MDSS_GDSC>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-volup {
+			label = "Volume Up";
+			linux,code = <KEY_VOLUMEUP>;
+			gpios = <&tlmm 91 GPIO_ACTIVE_LOW>;
+			debounce-interval = <15>;
+		};
+	};
+
+	reserved-memory {
+		/delete-node/ reserved@85b00000;
+		qseecom_mem: reserved@84a00000 {
+			reg = <0x0 0x84a00000 0x0 0x1900000>;
+			no-map;
+		};
+
+		framebuffer_mem: memory@90001000 {
+			reg = <0x0 0x90001000 0x0 (720 * 1280 * 3)>;
+			no-map;
+		};
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&blsp_i2c3 {
+	status = "okay";
+
+	touchscreen@38 {
+		compatible = "edt,edt-ft5306";
+		reg = <0x38>;
+		interrupt-parent = <&tlmm>;
+		interrupts = <65 0x2008>;
+		reset-gpios = <&tlmm 64 GPIO_ACTIVE_LOW>;
+		vcc-supply = <&pm8937_l10>;
+		iovcc-supply = <&pm8937_l5>;
+
+		touchscreen-size-x = <720>;
+		touchscreen-size-y = <1280>;
+	};
+};
+
+&blsp_i2c5 {
+	status = "okay";
+
+	bq27426@55 {
+		compatible = "ti,bq27426";
+		reg = <0x55>;
+		monitored-battery = <&battery>;
+	};
+
+	bq25601@6b{
+		compatible = "ti,bq25601";
+		reg = <0x6b>;
+		monitored-battery = <&battery>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <61 IRQ_TYPE_EDGE_FALLING>;
+
+		input-voltage-limit-microvolt = <4400000>;
+		input-current-limit-microamp = <1000000>;
+	};
+};
+
+&pm8937_resin {
+	linux,code = <KEY_VOLUMEDOWN>;
+	status = "okay";
+};
+
+&pm8937_spmi_regulators {
+	pm8937_s5: s5 {
+		regulator-min-microvolt = <1050000>;
+		regulator-max-microvolt = <1350000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&rpm_requests {
+	regulators-0 {
+		compatible = "qcom,rpm-pm8937-regulators";
+
+		vdd_s1-supply = <&vph_pwr>;
+		vdd_s2-supply = <&vph_pwr>;
+		vdd_s3-supply = <&vph_pwr>;
+		vdd_s4-supply = <&vph_pwr>;
+
+		vdd_l1_l19-supply = <&pm8937_s3>;
+		vdd_l2_l23-supply = <&pm8937_s3>;
+		vdd_l3-supply = <&pm8937_s3>;
+		vdd_l4_l5_l6_l7_l16-supply = <&pm8937_s4>;
+		vdd_l8_l11_l12_l17_l22-supply = <&vph_pwr>;
+		vdd_l9_l10_l13_l14_l15_l18-supply = <&vph_pwr>;
+
+		pm8937_s1: s1 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8937_s3: s3 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8937_s4: s4 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8937_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8937_l5: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8937_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8937_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8937_l8: l8 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2900000>;
+		};
+
+		pm8937_l9: l9 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8937_l10: l10 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8937_l11: l11 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8937_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8937_l13: l13 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+
+		pm8937_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8937_l15: l15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8937_l16: l16 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8937_l17: l17 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2900000>;
+		};
+
+		pm8937_l19: l19 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8937_l22: l22 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+
+		pm8937_l23: l23 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+	};
+
+};
+
+&sdhc_1 {
+	vmmc-supply = <&pm8937_l8>;
+	vqmmc-supply = <&pm8937_l5>;
+	status = "okay";
+};
+
+&sdhc_2 {
+	cd-gpios = <&tlmm 67 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&pm8937_l11>;
+	vqmmc-supply = <&pm8937_l12>;
+	status = "okay";
+};
+
+&wcnss {
+	vddpx-supply = <&pm8937_l5>;
+	status = "okay";
+
+};
+
+&wcnss_iris {
+	compatible = "qcom,wcn3620";
+	vddxo-supply = <&pm8937_l7>;
+	vddrfa-supply = <&pm8937_l19>;
+	vddpa-supply = <&pm8937_l9>;
+	vdddig-supply = <&pm8937_l5>;
+};
+
+&wcnss_mem {
+	status = "okay";
+};

-- 
2.47.0

Re: [PATCH RFC 04/14] pinctrl: qcom: spmi-mpp: Add PM8937 compatible

[Dmitry Baryshkov]

On Sat, Oct 19, 2024 at 01:50:41PM +0200, Barnabás Czémán wrote:
> The PM8937 provides 4 MPPs.
> Add a compatible to support them.
> 
> Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
> ---
>  drivers/pinctrl/qcom/pinctrl-spmi-mpp.c | 1 +
>  1 file changed, 1 insertion(+)
> 

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

-- 
With best wishes
Dmitry

Re: [PATCH RFC 07/14] pinctrl: qcom: Add MSM8917 tlmm pinctrl driver

[Dmitry Baryshkov]

On Sat, Oct 19, 2024 at 01:50:44PM +0200, Barnabás Czémán wrote:
> From: Otto Pflüger <otto.pflueger@abscue.de>
> 
> It is based on MSM8916 driver with the pinctrl definitions from
> Qualcomm's downstream MSM8917 driver.
> 
> Signed-off-by: Otto Pflüger <otto.pflueger@abscue.de>
> Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
> ---
>  drivers/pinctrl/qcom/Kconfig.msm       |    6 +
>  drivers/pinctrl/qcom/Makefile          |    1 +
>  drivers/pinctrl/qcom/pinctrl-msm8917.c | 1622 ++++++++++++++++++++++++++++++++
>  3 files changed, 1629 insertions(+)
> 
> diff --git a/drivers/pinctrl/qcom/Kconfig.msm b/drivers/pinctrl/qcom/Kconfig.msm
> index c79f0c3c873da56e8c0e1de9f91bce4b552221d2..f53043ea213012447aaaf07e9f339a16493a1b95 100644
> --- a/drivers/pinctrl/qcom/Kconfig.msm
> +++ b/drivers/pinctrl/qcom/Kconfig.msm
> @@ -137,6 +137,12 @@ config PINCTRL_MSM8916
>  	  This is the pinctrl, pinmux, pinconf and gpiolib driver for the
>  	  Qualcomm TLMM block found on the Qualcomm 8916 platform.
>  
> +config PINCTRL_MSM8917
> +	tristate "Qualcomm 8917 pin controller driver"
> +	help
> +	  This is the pinctrl, pinmux, pinconf and gpiolib driver for the
> +	  Qualcomm TLMM block found on the Qualcomm 8917 platform.
> +

MSM8917, not just 8917.

[...]

> +	msm_mux_wcss_wlan2,
> +	msm_mux_webcam_rst,
> +	msm_mux_webcam_standby,
> +	msm_mux_wsa_io,
> +	msm_mux_wsa_irq,
> +	msm_mux_NA,

s/NA/_/ through the file, see recent tlmm drivers. This generally
improves readability.

> +};
> +

[...]

> +
> +static const struct msm_pingroup msm8917_groups[] = {
> +	PINGROUP(0, blsp_spi1, blsp_uart1, qdss_tracedata_b, NA, NA, NA, NA,
> +		 NA, NA),

And here too. Compare the string above with 

	PINGROUP(0, blsp_spi1, blsp_uart1, qdss_tracedata_b, _, _, _, _, _, _),

> +};
> +
> +#define NUM_GPIO_PINGROUPS	134

inline

> +
> +static const struct msm_pinctrl_soc_data msm8917_pinctrl = {
> +	.pins = msm8917_pins,
> +	.npins = ARRAY_SIZE(msm8917_pins),
> +	.functions = msm8917_functions,
> +	.nfunctions = ARRAY_SIZE(msm8917_functions),
> +	.groups = msm8917_groups,
> +	.ngroups = ARRAY_SIZE(msm8917_groups),
> +	.ngpios = NUM_GPIO_PINGROUPS,
> +};
> +
> +static int msm8917_pinctrl_probe(struct platform_device *pdev)
> +{
> +	return msm_pinctrl_probe(pdev, &msm8917_pinctrl);
> +}
> +
> +static const struct of_device_id msm8917_pinctrl_of_match[] = {
> +	{ .compatible = "qcom,msm8917-pinctrl", },
> +	{ },
> +};
> +
> +static struct platform_driver msm8917_pinctrl_driver = {
> +	.driver = {
> +		.name = "msm8917-pinctrl",
> +		.of_match_table = msm8917_pinctrl_of_match,
> +	},
> +	.probe = msm8917_pinctrl_probe,
> +	.remove_new = msm_pinctrl_remove,

Just .remove

> +};
> +
> +static int __init msm8917_pinctrl_init(void)
> +{
> +	return platform_driver_register(&msm8917_pinctrl_driver);
> +}
> +arch_initcall(msm8917_pinctrl_init);
> +
> +static void __exit msm8917_pinctrl_exit(void)
> +{
> +	platform_driver_unregister(&msm8917_pinctrl_driver);
> +}
> +module_exit(msm8917_pinctrl_exit);
> +
> +MODULE_DESCRIPTION("Qualcomm msm8917 pinctrl driver");
> +MODULE_LICENSE("GPL");
> +MODULE_DEVICE_TABLE(of, msm8917_pinctrl_of_match);

Please move this after the match table.

> 
> -- 
> 2.47.0
> 

-- 
With best wishes
Dmitry

Re: [PATCH RFC 01/14] dt-bindings: pinctrl: qcom,pmic-gpio: add PM8937

[Rob Herring (Arm)]

On Sat, 19 Oct 2024 13:50:38 +0200, Barnabás Czémán wrote:
> Document the 8 GPIOs found on PM8937. It has holes on
> 3,4 and 6 pins.
> 
> Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
> ---
>  Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.yaml | 3 +++
>  1 file changed, 3 insertions(+)
> 

My bot found errors running 'make dt_binding_check' on your patch:

yamllint warnings/errors:

dtschema/dtc warnings/errors:


doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20241019-msm8917-v1-1-f1f3ca1d88e5@mainlining.org

The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.

Re: [PATCH RFC 03/14] dt-bindings: pinctrl: qcom,pmic-mpp: Document PM8937 compatible

[Rob Herring (Arm)]

On Sat, 19 Oct 2024 13:50:40 +0200, Barnabás Czémán wrote:
> Document the Device Tree binding for PM8937 MPPs.
> 
> Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
> ---
>  Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.yaml | 2 ++
>  1 file changed, 2 insertions(+)
> 

My bot found errors running 'make dt_binding_check' on your patch:

yamllint warnings/errors:

dtschema/dtc warnings/errors:


doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20241019-msm8917-v1-3-f1f3ca1d88e5@mainlining.org

The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.

Re: [PATCH RFC 06/14] dt-bindings: pinctrl: qcom: Add MSM8917 pinctrl bindings

[Rob Herring (Arm)]

On Sat, 19 Oct 2024 13:50:43 +0200, Barnabás Czémán wrote:
> Add device tree bindings documentation for Qualcomm MSM8917
> pinctrl driver.
> 
> Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
> ---
>  .../bindings/pinctrl/qcom,msm8917-pinctrl.yaml     | 155 +++++++++++++++++++++
>  1 file changed, 155 insertions(+)
> 

My bot found errors running 'make dt_binding_check' on your patch:

yamllint warnings/errors:

dtschema/dtc warnings/errors:
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pinctrl/qcom,msm8917-pinctrl.yaml: ignoring, error parsing file

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20241019-msm8917-v1-6-f1f3ca1d88e5@mainlining.org

The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.

Re: [PATCH RFC 08/14] dt-bindings: mfd: qcom,tcsr: Add compatible for MSM8917

[Rob Herring (Arm)]

On Sat, 19 Oct 2024 13:50:45 +0200, Barnabás Czémán wrote:
> Document the qcom,msm8917-tcsr compatible.
> 
> Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
> ---
>  Documentation/devicetree/bindings/mfd/qcom,tcsr.yaml | 1 +
>  1 file changed, 1 insertion(+)
> 

My bot found errors running 'make dt_binding_check' on your patch:

yamllint warnings/errors:

dtschema/dtc warnings/errors:


doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20241019-msm8917-v1-8-f1f3ca1d88e5@mainlining.org

The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.

Re: [PATCH RFC 09/14] dt-bindings: thermal: tsens: Add MSM8917 compatible

[Rob Herring (Arm)]

On Sat, 19 Oct 2024 13:50:46 +0200, Barnabás Czémán wrote:
> Document the compatible string for tsens found in MSM8917.
> 
> Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
> ---
>  Documentation/devicetree/bindings/thermal/qcom-tsens.yaml | 1 +
>  1 file changed, 1 insertion(+)
> 

My bot found errors running 'make dt_binding_check' on your patch:

yamllint warnings/errors:

dtschema/dtc warnings/errors:


doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20241019-msm8917-v1-9-f1f3ca1d88e5@mainlining.org

The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.

Re: [PATCH RFC 10/14] dt-bindings: iommu: qcom,iommu: Add MSM8917 IOMMU to SMMUv1 compatibles

[Rob Herring (Arm)]

On Sat, 19 Oct 2024 13:50:47 +0200, Barnabás Czémán wrote:
> Add MSM8917 compatible string with "qcom,msm-iommu-v1" as fallback
> for the MSM8917 IOMMU which is compatible with Qualcomm's secure
> fw "SMMU v1" implementation.
> 
> Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
> ---
>  Documentation/devicetree/bindings/iommu/qcom,iommu.yaml | 1 +
>  1 file changed, 1 insertion(+)
> 

My bot found errors running 'make dt_binding_check' on your patch:

yamllint warnings/errors:

dtschema/dtc warnings/errors:


doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20241019-msm8917-v1-10-f1f3ca1d88e5@mainlining.org

The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.

Re: [PATCH RFC 11/14] dt-bindings: nvmem: Add compatible for MS8917

[Rob Herring (Arm)]

On Sat, 19 Oct 2024 13:50:48 +0200, Barnabás Czémán wrote:
> Document the QFPROM block found on MSM8917.
> 
> Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
> ---
>  Documentation/devicetree/bindings/nvmem/qcom,qfprom.yaml | 1 +
>  1 file changed, 1 insertion(+)
> 

My bot found errors running 'make dt_binding_check' on your patch:

yamllint warnings/errors:

dtschema/dtc warnings/errors:


doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20241019-msm8917-v1-11-f1f3ca1d88e5@mainlining.org

The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.

Re: [PATCH RFC 13/14] dt-bindings: arm: qcom: Add Xiaomi Redmi 5A

[Rob Herring (Arm)]

On Sat, 19 Oct 2024 13:50:50 +0200, Barnabás Czémán wrote:
> Document Xiaomi Remi 5A (riva).
> 
> Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
> ---
>  Documentation/devicetree/bindings/arm/qcom.yaml | 7 +++++++
>  1 file changed, 7 insertions(+)
> 

My bot found errors running 'make dt_binding_check' on your patch:

yamllint warnings/errors:

dtschema/dtc warnings/errors:


doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20241019-msm8917-v1-13-f1f3ca1d88e5@mainlining.org

The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.

Re: [PATCH RFC 12/14] arm64: dts: qcom: Add initial support for MSM8917

[Dmitry Baryshkov]

On Sat, Oct 19, 2024 at 01:50:49PM +0200, Barnabás Czémán wrote:
> From: Otto Pflüger <otto.pflueger@abscue.de>
> 
> Add initial support for MSM8917 SoC.
> 
> Signed-off-by: Otto Pflüger <otto.pflueger@abscue.de>
> [reword commit, rebase, fix schema errors]
> Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
> ---
>  arch/arm64/boot/dts/qcom/msm8917-pins.dtsi |  344 ++++++
>  arch/arm64/boot/dts/qcom/msm8917.dtsi      | 1557 ++++++++++++++++++++++++++++
>  arch/arm64/boot/dts/qcom/pm8916.dtsi       |    9 +-
>  3 files changed, 1909 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/msm8917-pins.dtsi b/arch/arm64/boot/dts/qcom/msm8917-pins.dtsi
> new file mode 100644
> index 0000000000000000000000000000000000000000..f283ffd59b8aca8e510ef95d5526af9592a1c036
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/msm8917-pins.dtsi

Please merge into msm8917.dtsi (for generic parts) and
msm8917-boatd.dtsi (for board-specific parts).

> @@ -0,0 +1,344 @@
> +// SPDX-License-Identifier: GPL-2.0

If possible, GPL-2.0 OR MIT, or GPL-2.0 OR BSD-2/3-Clause

> +&tlmm {
> +	blsp1_uart1_default: blsp1-uart1-default-state {
> +		pins = "gpio0", "gpio1", "gpio2", "gpio3";
> +		function = "blsp_uart1";
> +
> +		drive-strength = <16>;
> +		bias-disable;
> +	};
> +
> +	blsp1_uart1_sleep: blsp1-uart1-sleep-state {
> +		pins = "gpio0", "gpio1", "gpio2", "gpio3";
> +		function = "gpio";
> +
> +		drive-strength = <2>;
> +		bias-pull-down;
> +	};

Please sort all the pin states by the node name.

> +
> +	wcnss_pin_a: wcnss-active-state {
> +		wcss-wlan2-pins {
> +			pins = "gpio76";
> +			function = "wcss_wlan2";
> +			drive-strength = <6>;
> +			bias-pull-up;
> +
> +		};
> +
> +		wcss-wlan1-pins {

and subnodes too.

> +			pins = "gpio77";
> +			function = "wcss_wlan1";
> +			drive-strength = <6>;
> +			bias-pull-up;
> +
> +		};
> +
> +		wcss-wlan0-pins {
> +			pins = "gpio78";
> +			function = "wcss_wlan0";
> +			drive-strength = <6>;
> +			bias-pull-up;
> +
> +		};
> +
> +		wcss-wlan-pins {
> +			pins = "gpio79", "gpio80";
> +			function = "wcss_wlan";
> +			drive-strength = <6>;
> +			bias-pull-up;
> +
> +		};
> +	};
> +
> +	cci0_default: cci0-default-state {
> +		pins = "gpio29", "gpio30";
> +		function = "cci_i2c";
> +
> +
> +		drive-strength = <2>;
> +		bias-disable;
> +	};
> +
> +	cci1_default: cci1-default-state {
> +		pins = "gpio31", "gpio32";
> +		function = "cci_i2c";
> +
> +
> +		drive-strength = <2>;
> +		bias-disable;
> +	};
> +
> +	cdc_pdm_lines_act: pdm-lines-on-state {
> +		pins = "gpio69", "gpio70", "gpio71", "gpio72",
> +		       "gpio73", "gpio74";
> +		function = "cdc_pdm0";
> +
> +		drive-strength = <8>;
> +		bias-disable;
> +	};
> +
> +	cdc_pdm_lines_sus: pdm-lines-off-state {
> +		pins = "gpio69", "gpio70", "gpio71", "gpio72",
> +		       "gpio73", "gpio74";
> +		function = "cdc_pdm0";
> +
> +		drive-strength = <2>;
> +		bias-disable;
> +	};
> +};
> diff --git a/arch/arm64/boot/dts/qcom/msm8917.dtsi b/arch/arm64/boot/dts/qcom/msm8917.dtsi
> new file mode 100644
> index 0000000000000000000000000000000000000000..e5f580c6ec28ad6442b31a0e1ee256c376c5438d
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/msm8917.dtsi
> @@ -0,0 +1,1557 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +
> +#include <dt-bindings/clock/qcom,gcc-msm8917.h>
> +#include <dt-bindings/clock/qcom,rpmcc.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/power/qcom-rpmpd.h>
> +#include <dt-bindings/soc/qcom,apr.h>
> +#include <dt-bindings/sound/qcom,q6dsp-lpass-ports.h>
> +#include <dt-bindings/thermal/thermal.h>
> +
> +/ {
> +	interrupt-parent = <&intc>;
> +
> +	#address-cells = <2>;
> +	#size-cells = <2>;
> +
> +	aliases {
> +		mmc0 = &sdhc_1; /* SDC1 eMMC slot */
> +		mmc1 = &sdhc_2; /* SDC2 SD card slot */
> +	};
> +
> +	chosen { };
> +
> +	memory@80000000 {
> +		device_type = "memory";
> +		/* We expect the bootloader to fill in the reg */
> +		reg = <0 0x80000000 0 0>;
> +	};
> +
> +	reserved-memory {
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		ranges;
> +
> +		reserved@85b00000 {
> +			reg = <0x0 0x85b00000 0x0 0x800000>;
> +			no-map;
> +		};
> +
> +		smem@86300000 {
> +			compatible = "qcom,smem";
> +			reg = <0x0 0x86300000 0x0 0x100000>;
> +			no-map;
> +
> +			hwlocks = <&tcsr_mutex 3>;
> +			qcom,rpm-msg-ram = <&rpm_msg_ram>;
> +		};
> +
> +		reserved@86400000 {
> +			reg = <0x0 0x86400000 0x0 0x400000>;
> +			no-map;
> +		};
> +
> +		mpss_mem: mpss@86800000 {
> +			/*
> +			 * The memory region for the mpss firmware is generally
> +			 * relocatable and could be allocated dynamically.
> +			 * However, many firmware versions tend to fail when
> +			 * loaded to some special addresses, so it is hard to
> +			 * define reliable alloc-ranges.
> +			 *
> +			 * alignment = <0x0 0x400000>;
> +			 * alloc-ranges = <0x0 0x86800000 0x0 0x8000000>;
> +			 */
> +			reg = <0x0 0x86800000 0x0 0>; /* size is device-specific */
> +			no-map;
> +			status = "disabled";
> +		};
> +
> +		adsp_mem: adsp {
> +			size = <0x0 0x1100000>;
> +			alignment = <0x0 0x100000>;
> +			alloc-ranges = <0x0 0x86800000 0x0 0x8000000>;
> +			no-map;
> +			status = "disabled";
> +		};
> +
> +		wcnss_mem: wcnss {
> +			size = <0x0 0x700000>;
> +			alignment = <0x0 0x100000>;
> +			alloc-ranges = <0x0 0x86800000 0x0 0x8000000>;
> +			no-map;
> +			status = "disabled";
> +		};
> +
> +		venus_mem: venus {
> +			size = <0x0 0x400000>;
> +			alignment = <0x0 0x100000>;
> +			alloc-ranges = <0x0 0x86800000 0x0 0x8000000>;
> +			no-map;
> +			status = "disabled";
> +		};
> +
> +		mba_mem: mba {

Please sort these nodes too.

> +			size = <0x0 0x100000>;
> +			alignment = <0x0 0x100000>;
> +			alloc-ranges = <0x0 0x86800000 0x0 0x8000000>;
> +			no-map;
> +			status = "disabled";
> +		};
> +
> +		rmtfs@92100000 {

This one should be after mpss_mem, just before adsp.

> +			compatible = "qcom,rmtfs-mem";
> +			reg = <0x0 0x92100000 0x0 0x180000>;
> +			no-map;
> +
> +			qcom,client-id = <1>;
> +		};
> +	};
> +
> +	cpus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		CPU0: cpu@0 {

lowercase all labels.

> +			device_type = "cpu";
> +			compatible = "arm,cortex-a53";
> +			reg = <0x100>;
> +			next-level-cache = <&L2_0>;
> +			enable-method = "psci";
> +			clocks = <&apcs>;
> +			operating-points-v2 = <&cpu_opp_table>;
> +			#cooling-cells = <2>;
> +			power-domains = <&CPU_PD0>;
> +			power-domain-names = "psci";
> +		};
> +
> +		CPU1: cpu@1 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a53";
> +			reg = <0x101>;
> +			next-level-cache = <&L2_0>;
> +			enable-method = "psci";
> +			clocks = <&apcs>;
> +			operating-points-v2 = <&cpu_opp_table>;
> +			#cooling-cells = <2>;
> +			power-domains = <&CPU_PD1>;
> +			power-domain-names = "psci";
> +		};
> +
> +		CPU2: cpu@2 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a53";
> +			reg = <0x102>;
> +			next-level-cache = <&L2_0>;
> +			enable-method = "psci";
> +			clocks = <&apcs>;
> +			operating-points-v2 = <&cpu_opp_table>;
> +			#cooling-cells = <2>;
> +			power-domains = <&CPU_PD2>;
> +			power-domain-names = "psci";
> +		};
> +
> +		CPU3: cpu@3 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a53";
> +			reg = <0x103>;
> +			next-level-cache = <&L2_0>;
> +			enable-method = "psci";
> +			clocks = <&apcs>;
> +			operating-points-v2 = <&cpu_opp_table>;
> +			#cooling-cells = <2>;
> +			power-domains = <&CPU_PD3>;
> +			power-domain-names = "psci";
> +		};
> +
> +		L2_0: l2-cache {
> +			compatible = "cache";
> +			cache-level = <2>;
> +			cache-unified;
> +		};
> +
> +		cpu-map {
> +			cluster0 {
> +				core0 {
> +					cpu = <&CPU0>;
> +				};
> +
> +				core1 {
> +					cpu = <&CPU1>;
> +				};
> +
> +				core2 {
> +					cpu = <&CPU2>;
> +				};
> +
> +				core3 {
> +					cpu = <&CPU3>;
> +				};
> +			};
> +		};
> +
> +		idle-states {
> +			entry-method = "psci";
> +
> +			CPU_SLEEP_0: cpu-sleep-0 {
> +				compatible = "arm,idle-state";
> +				idle-state-name = "standalone-power-collapse";
> +				arm,psci-suspend-param = <0x40000003>;
> +				entry-latency-us = <125>;
> +				exit-latency-us = <180>;
> +				min-residency-us = <595>;
> +				local-timer-stop;
> +			};
> +		};
> +
> +		domain-idle-states {
> +			CLUSTER_PWRDN: cluster-gdhs {
> +				compatible = "domain-idle-state";
> +				arm,psci-suspend-param = <0x41000043>;
> +				entry-latency-us = <240>;
> +				exit-latency-us = <280>;
> +				min-residency-us = <806>;
> +			};
> +
> +			CLUSTER_RET: cluster-retention {
> +				compatible = "domain-idle-state";
> +				arm,psci-suspend-param = <0x41000023>;
> +				entry-latency-us = <700>;
> +				exit-latency-us = <650>;
> +				min-residency-us = <1972>;
> +			};
> +
> +			CLUSTER_PC: cluster-power-collapse {
> +				compatible = "domain-idle-state";
> +				arm,psci-suspend-param = <0x41000053>;
> +				entry-latency-us = <700>;
> +				exit-latency-us = <1000>;
> +				min-residency-us = <6500>;
> +			};
> +		};
> +	};
> +
> +	cpu_opp_table: opp-table-cpu {
> +		compatible = "operating-points-v2";
> +		opp-shared;
> +
> +		opp-960000000 {
> +			opp-hz = /bits/ 64 <960000000>;
> +		};
> +
> +		opp-1094400000 {
> +			opp-hz = /bits/ 64 <1094400000>;
> +		};
> +
> +		opp-1248000000 {
> +			opp-hz = /bits/ 64 <1248000000>;
> +		};
> +
> +		opp-1401600000 {
> +			opp-hz = /bits/ 64 <1401600000>;
> +		};
> +	};
> +
> +	timer {

Again, please sort the nodes.

> +		compatible = "arm,armv8-timer";
> +		interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> +			     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> +			     <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> +			     <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
> +		clock-frequency = <19200000>;
> +	};
> +
> +	clocks {
> +		xo_board: xo-board {
> +			compatible = "fixed-clock";
> +			#clock-cells = <0>;
> +			clock-frequency = <19200000>;
> +			clock-output-names = "xo";

Freq goes to the board dts.
Please drop clock-output-names.

> +		};
> +
> +		sleep_clk: sleep-clk {
> +			compatible = "fixed-clock";
> +			#clock-cells = <0>;
> +			clock-frequency = <32768>;
> +			clock-output-names = "sleep_clk";
> +		};
> +	};
> +
> +	firmware {
> +		scm: scm {
> +			compatible = "qcom,scm-msm8916", "qcom,scm";
> +			clocks = <&gcc GCC_CRYPTO_CLK>,
> +				 <&gcc GCC_CRYPTO_AXI_CLK>,
> +				 <&gcc GCC_CRYPTO_AHB_CLK>;
> +			clock-names = "core", "bus", "iface";
> +			#reset-cells = <1>;
> +
> +			qcom,dload-mode = <&tcsr 0x6100>;
> +		};
> +	};
> +
> +	pmu {
> +		compatible = "arm,cortex-a53-pmu";
> +		interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
> +	};
> +
> +	psci {
> +		compatible = "arm,psci-1.0";
> +		method = "smc";
> +
> +		CPU_PD0: power-domain-cpu0 {
> +			#power-domain-cells = <0>;
> +			power-domains = <&CLUSTER_PD>;
> +			domain-idle-states = <&CPU_SLEEP_0>;
> +		};
> +
> +		CPU_PD1: power-domain-cpu1 {
> +			#power-domain-cells = <0>;
> +			power-domains = <&CLUSTER_PD>;
> +			domain-idle-states = <&CPU_SLEEP_0>;
> +		};
> +
> +		CPU_PD2: power-domain-cpu2 {
> +			#power-domain-cells = <0>;
> +			power-domains = <&CLUSTER_PD>;
> +			domain-idle-states = <&CPU_SLEEP_0>;
> +		};
> +
> +		CPU_PD3: power-domain-cpu3 {
> +			#power-domain-cells = <0>;
> +			power-domains = <&CLUSTER_PD>;
> +			domain-idle-states = <&CPU_SLEEP_0>;
> +		};
> +
> +		CLUSTER_PD: power-domain-cluster {
> +			#power-domain-cells = <0>;
> +			domain-idle-states = <&CLUSTER_PWRDN>, <&CLUSTER_RET>, <&CLUSTER_PC>;
> +		};
> +	};
> +
> +	rpm: remoteproc {
> +		compatible = "qcom,msm8917-rpm-proc", "qcom,rpm-proc";
> +
> +		smd-edge {
> +			interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
> +			qcom,ipc = <&apcs 8 0>;
> +			qcom,smd-edge = <15>;
> +
> +			rpm_requests: rpm-requests {
> +				compatible = "qcom,rpm-msm8917", "qcom,smd-rpm";
> +				qcom,smd-channels = "rpm_requests";
> +
> +				rpmcc: clock-controller {
> +					compatible = "qcom,rpmcc-msm8917", "qcom,rpmcc";
> +					#clock-cells = <1>;
> +					clocks = <&xo_board>;
> +					clock-names = "xo";
> +				};
> +
> +				rpmpd: power-controller {
> +					compatible = "qcom,msm8917-rpmpd";
> +					#power-domain-cells = <1>;
> +					operating-points-v2 = <&rpmpd_opp_table>;
> +
> +					rpmpd_opp_table: opp-table {
> +						compatible = "operating-points-v2";
> +
> +						rpmpd_opp_ret: opp1 {
> +							opp-level = <RPM_SMD_LEVEL_RETENTION>;
> +						};
> +
> +						rpmpd_opp_ret_plus: opp2 {
> +							opp-level = <RPM_SMD_LEVEL_RETENTION_PLUS>;
> +						};
> +
> +						rpmpd_opp_min_svs: opp3 {
> +							opp-level = <RPM_SMD_LEVEL_MIN_SVS>;
> +						};
> +
> +						rpmpd_opp_low_svs: opp4 {
> +							opp-level = <RPM_SMD_LEVEL_LOW_SVS>;
> +						};
> +
> +						rpmpd_opp_svs: opp5 {
> +							opp-level = <RPM_SMD_LEVEL_SVS>;
> +						};
> +
> +						rpmpd_opp_svs_plus: opp6 {
> +							opp-level = <RPM_SMD_LEVEL_SVS_PLUS>;
> +						};
> +
> +						rpmpd_opp_nom: opp7 {
> +							opp-level = <RPM_SMD_LEVEL_NOM>;
> +						};
> +
> +						rpmpd_opp_nom_plus: opp8 {
> +							opp-level = <RPM_SMD_LEVEL_NOM_PLUS>;
> +						};
> +
> +						rpmpd_opp_turbo: opp9 {
> +							opp-level = <RPM_SMD_LEVEL_TURBO>;
> +						};
> +					};
> +				};
> +			};
> +		};
> +	};
> +
> +	smp2p-adsp {
> +		compatible = "qcom,smp2p";
> +		qcom,smem = <443>, <429>;
> +
> +		interrupts = <GIC_SPI 291 IRQ_TYPE_EDGE_RISING>;
> +
> +		mboxes = <&apcs 10>;
> +
> +		qcom,local-pid = <0>;
> +		qcom,remote-pid = <2>;
> +
> +		adsp_smp2p_out: master-kernel {
> +			qcom,entry-name = "master-kernel";
> +
> +			#qcom,smem-state-cells = <1>;
> +		};
> +
> +		adsp_smp2p_in: slave-kernel {
> +			qcom,entry-name = "slave-kernel";
> +
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +	};
> +
> +	smp2p-modem {
> +		compatible = "qcom,smp2p";
> +		qcom,smem = <435>, <428>;
> +
> +		interrupts = <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>;
> +
> +		qcom,ipc = <&apcs 8 14>;
> +
> +		qcom,local-pid = <0>;
> +		qcom,remote-pid = <1>;
> +
> +		modem_smp2p_out: master-kernel {
> +			qcom,entry-name = "master-kernel";
> +
> +			#qcom,smem-state-cells = <1>;
> +		};
> +
> +		modem_smp2p_in: slave-kernel {
> +			qcom,entry-name = "slave-kernel";
> +
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +	};
> +
> +	smp2p-wcnss {
> +		compatible = "qcom,smp2p";
> +		qcom,smem = <451>, <431>;
> +
> +		interrupts = <GIC_SPI 143 IRQ_TYPE_EDGE_RISING>;
> +
> +		qcom,ipc = <&apcs 8 18>;
> +
> +		qcom,local-pid = <0>;
> +		qcom,remote-pid = <4>;
> +
> +		wcnss_smp2p_out: master-kernel {
> +			qcom,entry-name = "master-kernel";
> +
> +			#qcom,smem-state-cells = <1>;
> +		};
> +
> +		wcnss_smp2p_in: slave-kernel {
> +			qcom,entry-name = "slave-kernel";
> +
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +	};
> +
> +	smsm {
> +		compatible = "qcom,smsm";
> +
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		qcom,ipc-1 = <&apcs 8 13>;
> +		qcom,ipc-3 = <&apcs 8 19>;

Please use mboxes instead

> +
> +		apps_smsm: apps@0 {
> +			reg = <0>;
> +
> +			#qcom,smem-state-cells = <1>;
> +		};
> +
> +		hexagon_smsm: hexagon@1 {
> +			reg = <1>;
> +			interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
> +
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +
> +		wcnss_smsm: wcnss@6 {
> +			reg = <6>;
> +			interrupts = <GIC_SPI 144 IRQ_TYPE_EDGE_RISING>;
> +
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +	};
> +
> +	soc: soc@0 {
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges = <0 0 0 0xffffffff>;
> +		compatible = "simple-bus";
> +
> +		rng@22000 {
> +			compatible = "qcom,prng";
> +			reg = <0xe3000 0x1000>;
> +			clocks = <&gcc GCC_PRNG_AHB_CLK>;
> +			clock-names = "core";
> +		};
> +
> +		restart@4ab000 {
> +			compatible = "qcom,pshold";
> +			reg = <0x004ab000 0x4>;
> +		};
> +
> +		qfprom: qfprom@a4000 {
> +			compatible = "qcom,msm8917-qfprom", "qcom,qfprom";
> +			reg = <0x000a4000 0x1000>;
> +			#address-cells = <1>;
> +			#size-cells = <1>;

empty line

> +			tsens_caldata: caldata@d0 {
> +				reg = <0x01d8 0x14>;
> +			};

No, individual bit definitions for each of tsens fuse values.

> +		};
> +
> +		rpm_msg_ram: sram@60000 {
> +			compatible = "qcom,rpm-msg-ram";
> +			reg = <0x00060000 0x8000>;
> +		};
> +
> +		tsens: thermal-sensor@4a9000 {
> +			compatible = "qcom,msm8917-tsens", "qcom,tsens-v1";
> +			reg = <0x004a9000 0x1000>,
> +			      <0x004a8000 0x1000>;
> +			nvmem-cells = <&tsens_caldata>;
> +			nvmem-cell-names = "calib";

And here too, individual bits instead of a single blob.

> +			#qcom,sensors = <10>;
> +			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "uplow";
> +			#thermal-sensor-cells = <1>;
> +		};
> +
> +		tlmm: pinctrl@1000000 {
> +			compatible = "qcom,msm8917-pinctrl";
> +			reg = <0x01000000 0x300000>;
> +			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
> +			gpio-controller;
> +			gpio-ranges = <&tlmm 0 0 134>;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +
> +		gcc: clock-controller@1800000 {
> +			compatible = "qcom,gcc-msm8917";
> +			#clock-cells = <1>;
> +			#reset-cells = <1>;
> +			#power-domain-cells = <1>;
> +			reg = <0x01800000 0x80000>;
> +			clocks = <&xo_board>,
> +				 <&sleep_clk>,
> +				 <&mdss_dsi0_phy 1>,
> +				 <&mdss_dsi0_phy 0>;
> +			clock-names = "xo",
> +				      "sleep_clk",
> +				      "dsi0pll",
> +				      "dsi0pllbyte";
> +		};
> +
> +		tcsr_mutex: hwlock@1905000 {
> +			compatible = "qcom,tcsr-mutex";
> +			reg = <0x01905000 0x20000>;
> +			#hwlock-cells = <1>;
> +		};
> +
> +		tcsr: syscon@1937000 {
> +			compatible = "qcom,tcsr-msm8917", "syscon";
> +			reg = <0x01937000 0x30000>;
> +		};
> +
> +		apps_iommu: iommu@1e00000 {
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			#iommu-cells = <1>;
> +			compatible = "qcom,msm8917-iommu", "qcom,msm-iommu-v1";
> +			ranges = <0 0x01e20000 0x20000>;
> +
> +			clocks = <&gcc GCC_SMMU_CFG_CLK>,
> +				 <&gcc GCC_APSS_TCU_CLK>;
> +			clock-names = "iface", "bus";
> +
> +			qcom,iommu-secure-id = <17>;
> +
> +			/* VFE */
> +			iommu-ctx@14000 {
> +				compatible = "qcom,msm-iommu-v1-ns";
> +				reg = <0x00014000 0x1000>;
> +				interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
> +			};
> +
> +			/* MDP_0 */
> +			iommu-ctx@15000 {
> +				compatible = "qcom,msm-iommu-v1-ns";
> +				reg = <0x00015000 0x1000>;
> +				interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
> +			};
> +
> +			/* VENUS_NS */
> +			iommu-ctx@16000 {
> +				compatible = "qcom,msm-iommu-v1-ns";
> +				reg = <0x00016000 0x1000>;
> +				interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
> +			};
> +		};
> +
> +		gpu_iommu: iommu@1f00000 {
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			#iommu-cells = <1>;
> +
> +			compatible = "qcom,msm8917-iommu", "qcom,msm-iommu-v1";
> +
> +			ranges = <0 0x01f08000 0x10000>;
> +			clocks = <&gcc GCC_SMMU_CFG_CLK>,
> +				 <&gcc GCC_GFX_TCU_CLK>;
> +			clock-names = "iface", "bus";
> +			qcom,iommu-secure-id = <18>;
> +
> +			iommu-ctx@0 {
> +				compatible = "qcom,msm-iommu-v2-ns";
> +				reg = <0x0000 0x1000>;
> +				interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>;
> +			};
> +		};
> +
> +		mdss: display-subsystem@1a00000 {

Please keep the nodes sorted by the address.

> +			compatible = "qcom,mdss";
> +			reg = <0x01a00000 0x1000>,
> +			      <0x01ab0000 0x1040>;
> +			reg-names = "mdss_phys", "vbif_phys";
> +
> +			power-domains = <&gcc MDSS_GDSC>;
> +
> +			clocks = <&gcc GCC_MDSS_AHB_CLK>,
> +				 <&gcc GCC_MDSS_AXI_CLK>,
> +				 <&gcc GCC_MDSS_VSYNC_CLK>;
> +			clock-names = "iface",
> +				      "bus",
> +				      "vsync";
> +
> +			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
> +
> +			interrupt-controller;
> +			#interrupt-cells = <1>;
> +
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges;
> +
> +			status = "disabled";
> +
> +			mdp: display-controller@1a01000 {
> +				compatible = "qcom,msm8917-mdp5", "qcom,mdp5";
> +				reg = <0x01a01000 0x89000>;
> +				reg-names = "mdp_phys";
> +
> +				interrupt-parent = <&mdss>;
> +				interrupts = <0>;
> +
> +				power-domains = <&gcc MDSS_GDSC>;
> +
> +				clocks = <&gcc GCC_MDSS_AHB_CLK>,
> +					 <&gcc GCC_MDSS_AXI_CLK>,
> +					 <&gcc GCC_MDSS_MDP_CLK>,
> +					 <&gcc GCC_MDSS_VSYNC_CLK>;
> +				clock-names = "iface",
> +					      "bus",
> +					      "core",
> +					      "vsync";
> +
> +				iommus = <&apps_iommu 0x15>;
> +
> +				ports {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +
> +					port@0 {
> +						reg = <0>;

Please add missing empty lines between properties and subnodes.

> +						mdp5_intf1_out: endpoint {

mdss_mdp_intf1_out:

> +							remote-endpoint = <&mdss_dsi0_in>;
> +						};
> +					};
> +				};
> +			};
> +
> +			mdss_dsi0: dsi@1a94000 {
> +				compatible = "qcom,mdss-dsi-ctrl";
> +				reg = <0x01a94000 0x300>;
> +				reg-names = "dsi_ctrl";
> +
> +				interrupt-parent = <&mdss>;
> +				interrupts = <4>;
> +
> +				assigned-clocks = <&gcc BYTE0_CLK_SRC>,
> +						  <&gcc PCLK0_CLK_SRC>;
> +				assigned-clock-parents = <&mdss_dsi0_phy 0>,
> +							 <&mdss_dsi0_phy 1>;
> +
> +				clocks = <&gcc GCC_MDSS_MDP_CLK>,
> +					 <&gcc GCC_MDSS_AHB_CLK>,
> +					 <&gcc GCC_MDSS_AXI_CLK>,
> +					 <&gcc GCC_MDSS_BYTE0_CLK>,
> +					 <&gcc GCC_MDSS_PCLK0_CLK>,
> +					 <&gcc GCC_MDSS_ESC0_CLK>;
> +				clock-names = "mdp_core",
> +					      "iface",
> +					      "bus",
> +					      "byte",
> +					      "pixel",
> +					      "core";
> +				phys = <&mdss_dsi0_phy>;
> +
> +				operating-points-v2 = <&mdss_dsi0_opp_table>;
> +				power-domains = <&rpmpd MSM8917_VDDCX>;
> +
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				ports {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +
> +					port@0 {
> +						reg = <0>;
> +						mdss_dsi0_in: endpoint {
> +							remote-endpoint = <&mdp5_intf1_out>;
> +						};
> +					};
> +
> +					port@1 {
> +						reg = <1>;
> +						mdss_dsi0_out: endpoint {
> +						};
> +					};
> +				};
> +
> +				mdss_dsi0_opp_table: opp-table {
> +					compatible = "operating-points-v2";
> +
> +					opp-125000000 {
> +						opp-hz = /bits/ 64 <125000000>;
> +						required-opps = <&rpmpd_opp_svs>;
> +					};
> +
> +					opp-187500000 {
> +						opp-hz = /bits/ 64 <187500000>;
> +						required-opps = <&rpmpd_opp_nom>;
> +					};
> +				};
> +			};
> +
> +			mdss_dsi0_phy: phy@1a94400 {
> +				compatible = "qcom,dsi-phy-28nm-8937";
> +				reg = <0x01a94a00 0xd4>,
> +				      <0x01a94400 0x280>,
> +				      <0x01a94b80 0x30>;
> +				reg-names = "dsi_pll",
> +					    "dsi_phy",
> +					    "dsi_phy_regulator";
> +
> +				#clock-cells = <1>;
> +				#phy-cells = <0>;
> +
> +				clocks = <&gcc GCC_MDSS_AHB_CLK>,
> +					 <&xo_board>;
> +				clock-names = "iface", "ref";
> +			};
> +		};
> +
> +		a53pll: clock@b016000 {
> +			compatible = "qcom,msm8939-a53pll";
> +			reg = <0x0b016000 0x40>;
> +			clocks = <&xo_board>;
> +			clock-names = "xo";
> +			#clock-cells = <0>;
> +			operating-points-v2 = <&pll_opp_table>;
> +
> +			pll_opp_table: opp-table {
> +				compatible = "operating-points-v2";
> +
> +				opp-960000000 {
> +					opp-hz = /bits/ 64 <960000000>;
> +				};
> +
> +				opp-1094400000 {
> +					opp-hz = /bits/ 64 <1094400000>;
> +				};
> +
> +				opp-1248000000 {
> +					opp-hz = /bits/ 64 <1248000000>;
> +				};
> +
> +				opp-1401600000 {
> +				      opp-hz = /bits/ 64 <1401600000>;
> +				};
> +			};
> +		};
> +
> +		gpu: gpu@1c00000 {
> +			compatible = "qcom,adreno-306.32", "qcom,adreno";

Is it really .32 ?

> +			reg = <0x01c00000 0x20000>;
> +			reg-names = "kgsl_3d0_reg_memory";
> +			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "kgsl_3d0_irq";
> +			clock-names = "core",
> +				      "iface",
> +				      "mem_iface",
> +				      "alt_mem_iface",
> +				      "gfx3d";
> +			clocks = <&gcc GCC_OXILI_GFX3D_CLK>,
> +				 <&gcc GCC_OXILI_AHB_CLK>,
> +				 <&gcc GCC_BIMC_GFX_CLK>,
> +				 <&gcc GCC_BIMC_GPU_CLK>,
> +				 <&gcc GFX3D_CLK_SRC>;
> +			power-domains = <&gcc OXILI_GX_GDSC>;
> +			operating-points-v2 = <&gpu_opp_table>;
> +			#cooling-cells = <2>;
> +
> +			iommus = <&gpu_iommu 0>;
> +
> +			status = "disabled";
> +
> +			gpu_opp_table: opp-table {
> +				compatible = "operating-points-v2";
> +
> +				opp-598000000 {
> +					opp-hz = /bits/ 64 <598000000>;
> +				};
> +
> +				opp-523200000 {
> +					opp-hz = /bits/ 64 <523200000>;
> +				};
> +
> +				opp-484800000 {
> +					opp-hz = /bits/ 64 <484800000>;
> +				};
> +
> +				opp-400000000 {
> +					opp-hz = /bits/ 64 <400000000>;
> +				};
> +
> +				opp-270000000 {
> +					opp-hz = /bits/ 64 <270000000>;
> +				};
> +
> +				opp-19200000 {
> +					opp-hz = /bits/ 64 <19200000>;
> +				};
> +			};
> +		};
> +
> +		spmi_bus: spmi@200f000 {
> +			compatible = "qcom,spmi-pmic-arb";
> +			reg = <0x0200f000 0x001000>,
> +			      <0x02400000 0x800000>,
> +			      <0x02c00000 0x800000>,
> +			      <0x03800000 0x200000>,
> +			      <0x0200a000 0x002100>;
> +			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
> +			interrupt-names = "periph_irq";
> +			interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
> +			qcom,ee = <0>;
> +			qcom,channel = <0>;
> +			#address-cells = <2>;
> +			#size-cells = <0>;
> +			interrupt-controller;
> +			#interrupt-cells = <4>;
> +		};
> +
> +		bam_dmux_dma: dma-controller@4044000 {
> +			compatible = "qcom,bam-v1.7.0";
> +			reg = <0x04044000 0x19000>;
> +			interrupts = <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>;
> +			#dma-cells = <1>;
> +			qcom,ee = <0>;
> +
> +			num-channels = <6>;
> +			qcom,num-ees = <1>;
> +			qcom,powered-remotely;
> +
> +			status = "disabled";
> +		};
> +
> +		apcs: mailbox@b011000 {
> +			compatible = "qcom,msm8939-apcs-kpss-global", "syscon";
> +			reg = <0x0b011000 0x1000>;
> +			#mbox-cells = <1>;
> +			clocks = <&a53pll>, <&gcc GPLL0_EARLY>, <&rpmcc RPM_SMD_XO_CLK_SRC>;
> +			clock-names = "pll", "aux", "ref";
> +			#clock-cells = <0>;
> +		};
> +
> +		sdhc_1: mmc@7824900 {
> +			compatible = "qcom,sdhci-msm-v4";
> +			reg = <0x07824900 0x500>, <0x07824000 0x800>;
> +			reg-names = "hc", "core";
> +
> +			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "hc_irq", "pwr_irq";
> +			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
> +				 <&gcc GCC_SDCC1_APPS_CLK>,
> +				 <&xo_board>;
> +			clock-names = "iface", "core", "xo";
> +			power-domains = <&rpmpd MSM8917_VDDCX>;
> +			mmc-hs200-1_8v;
> +			mmc-hs400-1_8v;
> +			mmc-ddr-1_8v;
> +			bus-width = <8>;
> +			non-removable;
> +			status = "disabled";
> +		};
> +
> +		sdhc_2: mmc@7864900 {
> +			compatible = "qcom,sdhci-msm-v4";
> +			reg = <0x07864900 0x500>, <0x07864000 0x800>;
> +			reg-names = "hc", "core";
> +
> +			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "hc_irq", "pwr_irq";
> +			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
> +				 <&gcc GCC_SDCC2_APPS_CLK>,
> +				 <&xo_board>;
> +			clock-names = "iface", "core", "xo";
> +			power-domains = <&rpmpd MSM8917_VDDCX>;
> +			bus-width = <4>;
> +			status = "disabled";
> +		};
> +
> +		blsp1_dma: dma-controller@7884000 {
> +			compatible = "qcom,bam-v1.7.0";
> +			reg = <0x07884000 0x1f000>;
> +			interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP1_AHB_CLK>;
> +			clock-names = "bam_clk";
> +			qcom,controlled-remotely;
> +			#dma-cells = <1>;
> +			num-channels = <12>;
> +			qcom,num-ees = <4>;
> +			qcom,ee = <0>;
> +		};
> +
> +		blsp2_dma: dma-controller@7ac4000 {
> +			compatible = "qcom,bam-v1.7.0";
> +			reg = <0x07ac4000 0x1d000>;
> +			interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP2_AHB_CLK>;
> +			clock-names = "bam_clk";
> +			qcom,controlled-remotely;
> +			#dma-cells = <1>;
> +			num-channels = <10>;
> +			qcom,num-ees = <4>;
> +			qcom,ee = <0>;
> +		};
> +
> +		blsp1_uart1: serial@78af000 {
> +			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
> +			reg = <0x078af000 0x200>;
> +			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>,
> +				 <&gcc GCC_BLSP1_AHB_CLK>;
> +			clock-names = "core", "iface";
> +			dmas = <&blsp1_dma 0>, <&blsp1_dma 1>;
> +			dma-names = "tx", "rx";
> +			pinctrl-names = "default", "sleep";
> +			pinctrl-0 = <&blsp1_uart1_default>;
> +			pinctrl-1 = <&blsp1_uart1_sleep>;
> +			status = "disabled";
> +		};
> +
> +		blsp1_uart2: serial@78b0000 {
> +			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
> +			reg = <0x078b0000 0x200>;
> +			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>,
> +				 <&gcc GCC_BLSP1_AHB_CLK>;
> +			clock-names = "core", "iface";
> +			dmas = <&blsp1_dma 2>, <&blsp1_dma 3>;
> +			dma-names = "tx", "rx";
> +			pinctrl-names = "default", "sleep";
> +			pinctrl-0 = <&blsp1_uart2_default>;
> +			pinctrl-1 = <&blsp1_uart2_sleep>;
> +			status = "disabled";
> +		};
> +
> +		blsp_i2c2: i2c@78b6000 {
> +			compatible = "qcom,i2c-qup-v2.2.1";
> +			reg = <0x078b6000 0x600>;
> +			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
> +				 <&gcc GCC_BLSP1_AHB_CLK>;
> +			clock-names = "core", "iface";
> +			dmas = <&blsp1_dma 6>, <&blsp1_dma 7>;
> +			dma-names = "tx", "rx";
> +			pinctrl-names = "default", "sleep";
> +			pinctrl-0 = <&i2c2_default>;
> +			pinctrl-1 = <&i2c2_sleep>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +
> +		blsp_i2c3: i2c@78b7000 {
> +			compatible = "qcom,i2c-qup-v2.2.1";
> +			reg = <0x078b7000 0x600>;
> +			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
> +				 <&gcc GCC_BLSP1_AHB_CLK>;
> +			clock-names = "core", "iface";
> +			dmas = <&blsp1_dma 8>, <&blsp1_dma 9>;
> +			dma-names = "tx", "rx";
> +			pinctrl-names = "default", "sleep";
> +			pinctrl-0 = <&i2c3_default>;
> +			pinctrl-1 = <&i2c3_sleep>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +
> +		blsp_spi3: spi@78b7000 {
> +			compatible = "qcom,spi-qup-v2.2.1";
> +			reg = <0x078b7000 0x600>;
> +			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP1_QUP3_SPI_APPS_CLK>,
> +				 <&gcc GCC_BLSP1_AHB_CLK>;
> +			clock-names = "core", "iface";
> +			dmas = <&blsp1_dma 8>, <&blsp1_dma 9>;
> +			dma-names = "tx", "rx";
> +			pinctrl-names = "default", "sleep";
> +			pinctrl-0 = <&spi3_default>;
> +			pinctrl-1 = <&spi3_sleep>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +
> +		blsp_i2c4: i2c@78b8000 {
> +			compatible = "qcom,i2c-qup-v2.2.1";
> +			reg = <0x078b8000 0x500>;
> +			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>,
> +				 <&gcc GCC_BLSP1_AHB_CLK>;
> +			clock-names = "core", "iface";
> +			dmas = <&blsp1_dma 10>, <&blsp1_dma 11>;
> +			dma-names = "tx", "rx";
> +			pinctrl-names = "default", "sleep";
> +			pinctrl-0 = <&i2c4_default>;
> +			pinctrl-1 = <&i2c4_sleep>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +
> +		blsp_i2c5: i2c@7af5000 {
> +			compatible = "qcom,i2c-qup-v2.2.1";
> +			reg = <0x07af5000 0x600>;
> +			interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>,
> +				 <&gcc GCC_BLSP2_AHB_CLK>;
> +			clock-names = "core", "iface";
> +			dmas = <&blsp2_dma 4>, <&blsp2_dma 5>;
> +			dma-names = "tx", "rx";
> +			pinctrl-names = "default", "sleep";
> +			pinctrl-0 = <&i2c5_default>;
> +			pinctrl-1 = <&i2c5_sleep>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +
> +		blsp_spi6: spi@7af6000 {
> +			compatible = "qcom,spi-qup-v2.2.1";
> +			reg = <0x07af6000 0x600>;
> +			interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP2_QUP2_SPI_APPS_CLK>,
> +				 <&gcc GCC_BLSP2_AHB_CLK>;
> +			clock-names = "core", "iface";
> +			dmas = <&blsp2_dma 6>, <&blsp2_dma 7>;
> +			dma-names = "tx", "rx";
> +			pinctrl-names = "default", "sleep";
> +			pinctrl-0 = <&spi6_default>;
> +			pinctrl-1 = <&spi6_sleep>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +
> +		usb_hs_phy: phy@6c000 {
> +			compatible = "qcom,usb-hs-28nm-femtophy";
> +			reg = <0x6c000 0x200>;
> +			#phy-cells = <0>;
> +			clocks = <&xo_board>,
> +				 <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>,
> +				 <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
> +			clock-names = "ref", "ahb", "sleep";
> +			resets = <&gcc GCC_QUSB2_PHY_BCR>,
> +				 <&gcc GCC_USB2_HS_PHY_ONLY_BCR>;
> +			reset-names = "phy", "por";
> +			status = "disabled";
> +		};
> +
> +		usb: usb@78db000 {
> +			compatible = "qcom,ci-hdrc";
> +			reg = <0x078db000 0x200>,
> +			      <0x078db200 0x200>;
> +			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_USB_HS_AHB_CLK>,
> +				 <&gcc GCC_USB_HS_SYSTEM_CLK>;
> +			clock-names = "iface", "core";
> +			assigned-clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>;
> +			assigned-clock-rates = <80000000>;
> +			resets = <&gcc GCC_USB_HS_BCR>;
> +			reset-names = "core";
> +			phy_type = "ulpi";
> +			dr_mode = "otg";
> +			hnp-disable;
> +			srp-disable;
> +			adp-disable;
> +			ahb-burst-config = <0>;
> +			phy-names = "usb-phy";
> +			phys = <&usb_hs_phy>;
> +			status = "disabled";
> +			#reset-cells = <1>;
> +		};
> +
> +		pronto: wcnss: remoteproc@a21b000 {

One label should be enough.

> +			compatible = "qcom,pronto-v3-pil", "qcom,pronto";
> +			reg = <0x0a204000 0x2000>, <0x0a202000 0x1000>, <0x0a21b000 0x3000>;
> +			reg-names = "ccu", "dxe", "pmu";
> +
> +			memory-region = <&wcnss_mem>;
> +
> +			interrupts-extended = <&intc GIC_SPI 149 IRQ_TYPE_EDGE_RISING>,
> +					      <&wcnss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
> +					      <&wcnss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
> +					      <&wcnss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
> +					      <&wcnss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
> +			interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";
> +
> +			power-domains = <&rpmpd MSM8917_VDDCX>,
> +					<&rpmpd MSM8917_VDDMX>;
> +			power-domain-names = "cx", "mx";
> +
> +			qcom,smem-states = <&wcnss_smp2p_out 0>;
> +			qcom,smem-state-names = "stop";
> +
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&wcnss_pin_a>;
> +
> +			status = "disabled";
> +
> +			wcnss_iris: iris {
> +				clocks = <&rpmcc RPM_SMD_RF_CLK2>;
> +				clock-names = "xo";
> +			};
> +
> +			smd-edge {
> +				interrupts = <GIC_SPI 142 IRQ_TYPE_EDGE_RISING>;
> +
> +				qcom,ipc = <&apcs 8 17>;

mboxes

> +				qcom,smd-edge = <6>;
> +				qcom,remote-pid = <4>;
> +
> +				label = "pronto";
> +
> +				wcnss_ctrl: wcnss {
> +					compatible = "qcom,wcnss";
> +					qcom,smd-channels = "WCNSS_CTRL";
> +
> +					qcom,mmio = <&pronto>;
> +
> +					wcnss_bt: bluetooth {
> +						compatible = "qcom,wcnss-bt";
> +					};
> +
> +					wcnss_wifi: wifi {
> +						compatible = "qcom,wcnss-wlan";
> +
> +						interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
> +							     <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
> +						interrupt-names = "tx", "rx";
> +
> +						qcom,smem-states = <&apps_smsm 10>, <&apps_smsm 9>;
> +						qcom,smem-state-names = "tx-enable",
> +									"tx-rings-empty";
> +					};
> +				};
> +			};
> +		};
> +
> +		intc: interrupt-controller@b000000 {
> +			compatible = "qcom,msm-qgic2";
> +			interrupt-controller;
> +			#interrupt-cells = <3>;
> +			reg = <0x0b000000 0x1000>,
> +			      <0x0b002000 0x1000>;
> +		};
> +
> +		watchdog@b017000 {
> +			compatible = "qcom,apss-wdt-qcs404", "qcom,kpss-wdt";
> +			reg = <0x0b017000 0x1000>;
> +			clocks = <&sleep_clk>;
> +		};
> +
> +		timer@b120000 {
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges;
> +			compatible = "arm,armv7-timer-mem";
> +			reg = <0x0b120000 0x1000>;
> +			clock-frequency = <19200000>;
> +
> +			frame@b121000 {
> +				frame-number = <0>;
> +				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
> +					     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
> +				reg = <0x0b121000 0x1000>,
> +				      <0x0b122000 0x1000>;
> +			};
> +
> +			frame@b123000 {
> +				frame-number = <1>;
> +				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
> +				reg = <0x0b123000 0x1000>;
> +				status = "disabled";
> +			};
> +
> +			frame@b124000 {
> +				frame-number = <2>;
> +				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
> +				reg = <0x0b124000 0x1000>;
> +				status = "disabled";
> +			};
> +
> +			frame@b125000 {
> +				frame-number = <3>;
> +				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
> +				reg = <0x0b125000 0x1000>;
> +				status = "disabled";
> +			};
> +
> +			frame@b126000 {
> +				frame-number = <4>;
> +				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
> +				reg = <0x0b126000 0x1000>;
> +				status = "disabled";
> +			};
> +
> +			frame@b127000 {
> +				frame-number = <5>;
> +				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
> +				reg = <0x0b127000 0x1000>;
> +				status = "disabled";
> +			};
> +
> +			frame@b128000 {
> +				frame-number = <6>;
> +				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
> +				reg = <0x0b128000 0x1000>;
> +				status = "disabled";
> +			};
> +		};
> +	};
> +
> +	thermal_zones: thermal-zones {
> +		aoss-thermal {
> +			polling-delay-passive = <250>;
> +			polling-delay = <1000>;
> +
> +			thermal-sensors = <&tsens 0>;
> +
> +			trips {
> +				aoss_alert0: trip-point0 {
> +					temperature = <85000>;
> +					hysteresis = <2000>;
> +					type = "hot";
> +				};
> +			};
> +		};
> +
> +		mdm-core-thermal {
> +			polling-delay-passive = <250>;
> +			polling-delay = <1000>;
> +
> +			thermal-sensors = <&tsens 1>;
> +
> +			trips {
> +				mdm_core_alert0: trip-point0 {
> +					temperature = <85000>;
> +					hysteresis = <2000>;
> +					type = "hot";
> +				};
> +			};
> +		};
> +
> +		q6-thermal {
> +			polling-delay-passive = <250>;
> +			polling-delay = <1000>;
> +
> +			thermal-sensors = <&tsens 2>;
> +
> +			trips {
> +				q6_alert0: trip-point0 {
> +					temperature = <85000>;
> +					hysteresis = <2000>;
> +					type = "hot";
> +				};
> +			};
> +		};
> +
> +		camera-thermal {
> +			polling-delay-passive = <250>;
> +			polling-delay = <1000>;
> +
> +			thermal-sensors = <&tsens 3>;
> +
> +			trips {
> +				camera_alert0: trip-point0 {
> +					temperature = <85000>;
> +					hysteresis = <2000>;
> +					type = "hot";
> +				};
> +			};
> +		};
> +
> +		cpuss1-thermal {
> +			polling-delay-passive = <250>;
> +			polling-delay = <1000>;
> +
> +			thermal-sensors = <&tsens 4>;
> +
> +			trips {
> +				cpuss1_alert0: trip-point0 {
> +					temperature = <75000>;
> +					hysteresis = <2000>;
> +					type = "passive";
> +				};
> +
> +				cpuss1_alert1: trip-point1 {
> +					temperature = <85000>;
> +					hysteresis = <2000>;
> +					type = "hot";
> +				};
> +
> +				cpuss1_crit: cpuss1-crit {
> +					temperature = <100000>;
> +					hysteresis = <2000>;
> +					type = "critical";
> +				};
> +			};
> +			cooling-maps {
> +				map0 {
> +					trip = <&cpuss1_alert0>;
> +					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +				};
> +			};
> +		};
> +
> +		cpu0-thermal {
> +			polling-delay-passive = <250>;
> +			polling-delay = <1000>;
> +
> +			thermal-sensors = <&tsens 5>;
> +
> +			trips {
> +				cpu0_alert0: trip-point0 {
> +					temperature = <75000>;
> +					hysteresis = <2000>;
> +					type = "passive";
> +				};
> +
> +				cpu0_alert1: trip-point1 {
> +					temperature = <85000>;
> +					hysteresis = <2000>;
> +					type = "hot";
> +				};
> +
> +				cpu0_crit: cpu-crit {
> +					temperature = <100000>;
> +					hysteresis = <2000>;
> +					type = "critical";
> +				};
> +			};
> +			cooling-maps {
> +				map0 {
> +					trip = <&cpu0_alert1>;
> +					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +				};
> +			};
> +		};
> +
> +		cpu1-thermal {
> +			polling-delay-passive = <250>;
> +			polling-delay = <1000>;
> +
> +			thermal-sensors = <&tsens 6>;
> +
> +			trips {
> +				cpu1_alert0: trip-point0 {
> +					temperature = <75000>;
> +					hysteresis = <2000>;
> +					type = "hot";
> +				};
> +
> +				cpu1_alert1: trip-point1 {
> +					temperature = <85000>;
> +					hysteresis = <2000>;
> +					type = "passive";
> +				};
> +
> +				cpu1_crit: cpu-crit {
> +					temperature = <100000>;
> +					hysteresis = <2000>;
> +					type = "critical";
> +				};
> +			};
> +			cooling-maps {
> +				map0 {
> +					trip = <&cpu1_alert1>;
> +					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +				};
> +			};
> +		};
> +
> +		cpu2-thermal {
> +			polling-delay-passive = <250>;
> +			polling-delay = <1000>;
> +
> +			thermal-sensors = <&tsens 7>;
> +
> +			trips {
> +				cpu2_alert0: trip-point0 {
> +					temperature = <75000>;
> +					hysteresis = <2000>;
> +					type = "hot";
> +				};
> +
> +				cpu2_alert1: trip-point1 {
> +					temperature = <85000>;
> +					hysteresis = <2000>;
> +					type = "passive";
> +				};
> +
> +				cpu2_crit: cpu-crit {
> +					temperature = <100000>;
> +					hysteresis = <2000>;
> +					type = "critical";
> +				};
> +			};
> +			cooling-maps {
> +				map0 {
> +					trip = <&cpu2_alert1>;
> +					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +				};
> +			};
> +		};
> +
> +		cpu3-thermal {
> +			polling-delay-passive = <250>;
> +			polling-delay = <1000>;
> +
> +			thermal-sensors = <&tsens 8>;
> +
> +			trips {
> +				cpu3_alert0: trip-point0 {
> +					temperature = <75000>;
> +					hysteresis = <2000>;
> +					type = "hot";
> +				};
> +
> +				cpu3_alert1: trip-point1 {
> +					temperature = <85000>;
> +					hysteresis = <2000>;
> +					type = "passive";
> +				};
> +
> +				cpu3_crit: cpu-crit {
> +					temperature = <100000>;
> +					hysteresis = <2000>;
> +					type = "critical";
> +				};
> +			};
> +			cooling-maps {
> +				map0 {
> +					trip = <&cpu3_alert1>;
> +					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +				};
> +			};
> +		};
> +
> +		gpu-thermal {
> +			polling-delay-passive = <250>;
> +			polling-delay = <1000>;
> +
> +			thermal-sensors = <&tsens 9>;
> +
> +			trips {
> +				gpu_alert: trip-point0 {
> +					temperature = <70000>;
> +					hysteresis = <2000>;
> +					type = "passive";
> +				};
> +
> +				gpu_crit: gpu-crit {
> +					temperature = <90000>;
> +					hysteresis = <2000>;
> +					type = "critical";
> +				};
> +			};
> +
> +			cooling-maps {
> +				map0 {
> +					trip = <&gpu_alert>;
> +					cooling-device = <&gpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +#include "msm8917-pins.dtsi"
> diff --git a/arch/arm64/boot/dts/qcom/pm8916.dtsi b/arch/arm64/boot/dts/qcom/pm8916.dtsi
> index f8e4829ff7f7de1f1f4f5da0f41020875d6c7e17..df0f679250ccb6c49a76288fad12f67b01fa6b61 100644
> --- a/arch/arm64/boot/dts/qcom/pm8916.dtsi
> +++ b/arch/arm64/boot/dts/qcom/pm8916.dtsi

Separate commit, please. Or move this to the board file submission.

> @@ -47,7 +47,7 @@ pon@800 {
>  			mode-bootloader = <0x2>;
>  			mode-recovery = <0x1>;
>  
> -			pwrkey {
> +			pm8916_pwrkey: pwrkey {
>  				compatible = "qcom,pm8941-pwrkey";
>  				interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
>  				debounce = <15625>;
> @@ -210,6 +210,10 @@ pm8916_pwm: pwm {
>  			status = "disabled";
>  		};
>  
> +		pm8916_spmi_regulators: regulators {
> +			compatible = "qcom,pm8916-regulators";
> +		};
> +
>  		pm8916_vib: vibrator@c000 {
>  			compatible = "qcom,pm8916-vib";
>  			reg = <0xc000>;
> @@ -219,6 +223,9 @@ pm8916_vib: vibrator@c000 {
>  		pm8916_codec: audio-codec@f000 {
>  			compatible = "qcom,pm8916-wcd-analog-codec";
>  			reg = <0xf000>;
> +			reg-names = "pmic-codec-core";
> +			clocks = <&xo_board>;
> +			clock-names = "mclk";

Why? Is this compatible with other boards?

>  			interrupt-parent = <&spmi_bus>;
>  			interrupts = <0x1 0xf0 0x0 IRQ_TYPE_NONE>,
>  				     <0x1 0xf0 0x1 IRQ_TYPE_NONE>,
> 
> -- 
> 2.47.0
> 

-- 
With best wishes
Dmitry

Re: [PATCH RFC 14/14] arm64: dts: qcom: Add Xiaomi Redmi 5A

[Dmitry Baryshkov]

On Sat, Oct 19, 2024 at 01:50:51PM +0200, Barnabás Czémán wrote:
> Add initial support for Xiaomi Redmi 5A (riva).
> 
> Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
> ---
>  arch/arm64/boot/dts/qcom/Makefile                |   1 +
>  arch/arm64/boot/dts/qcom/msm8917-xiaomi-riva.dts | 295 +++++++++++++++++++++++
>  2 files changed, 296 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 065bb19481c16db2affd291826d420c83a89c52a..79add0e07d8a5f3362d70b0aaaaa9b8c48e31239 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -59,6 +59,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-wingtech-wt86518.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-wingtech-wt86528.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-wingtech-wt88047.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-yiming-uz801v3.dtb
> +dtb-$(CONFIG_ARCH_QCOM)	+= msm8917-xiaomi-riva.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= msm8929-wingtech-wt82918hd.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= msm8939-huawei-kiwi.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= msm8939-longcheer-l9100.dtb
> diff --git a/arch/arm64/boot/dts/qcom/msm8917-xiaomi-riva.dts b/arch/arm64/boot/dts/qcom/msm8917-xiaomi-riva.dts
> new file mode 100644
> index 0000000000000000000000000000000000000000..7553f73603fc87797b0d424a2af6f2da65c90f5f
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/msm8917-xiaomi-riva.dts
> @@ -0,0 +1,295 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2023, Barnabas Czeman
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/arm/qcom,ids.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/leds/common.h>
> +#include "msm8917.dtsi"
> +#include "pm8937.dtsi"
> +
> +/ {
> +	model = "Xiaomi Redmi 5A (riva)";
> +	compatible = "xiaomi,riva", "qcom,msm8917";
> +	chassis-type = "handset";
> +
> +	qcom,msm-id = <QCOM_ID_MSM8917 0>;
> +	qcom,board-id = <0x1000b 2>, <0x2000b 2>;

Is this required to boot?

> +
> +	battery: battery {
> +		compatible = "simple-battery";
> +		charge-full-design-microamp-hours = <3000000>;
> +		energy-full-design-microwatt-hours = <11500000>;
> +		constant-charge-current-max-microamp = <1000000>;
> +		constant-charge-voltage-max-microvolt = <4400000>;
> +		precharge-current-microamp = <256000>;
> +		charge-term-current-microamp = <60000>;
> +		voltage-min-design-microvolt = <3400000>;
> +	};
> +
> +	chosen {
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		ranges;
> +
> +		stdout-path = "framebuffer0";
> +
> +		framebuffer0: framebuffer@90001000 {
> +			compatible = "simple-framebuffer";
> +			reg = <0x0 0x90001000 0x0 (720 * 1280 * 3)>;
> +			width = <720>;
> +			height = <1280>;
> +			stride = <(720 * 3)>;
> +			format = "r8g8b8";
> +
> +			clocks = <&gcc GCC_MDSS_AHB_CLK>,
> +				 <&gcc GCC_MDSS_AXI_CLK>,
> +				 <&gcc GCC_MDSS_VSYNC_CLK>,
> +				 <&gcc GCC_MDSS_MDP_CLK>,
> +				 <&gcc GCC_MDSS_BYTE0_CLK>,
> +				 <&gcc GCC_MDSS_PCLK0_CLK>,
> +				 <&gcc GCC_MDSS_ESC0_CLK>;
> +			power-domains = <&gcc MDSS_GDSC>;
> +		};
> +	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +
> +		key-volup {
> +			label = "Volume Up";
> +			linux,code = <KEY_VOLUMEUP>;
> +			gpios = <&tlmm 91 GPIO_ACTIVE_LOW>;
> +			debounce-interval = <15>;
> +		};
> +	};
> +
> +	reserved-memory {
> +		/delete-node/ reserved@85b00000;
> +		qseecom_mem: reserved@84a00000 {
> +			reg = <0x0 0x84a00000 0x0 0x1900000>;
> +			no-map;
> +		};
> +
> +		framebuffer_mem: memory@90001000 {
> +			reg = <0x0 0x90001000 0x0 (720 * 1280 * 3)>;
> +			no-map;
> +		};
> +	};
> +
> +	vph_pwr: vph-pwr-regulator {

regulator-vph-pwr, please

> +		compatible = "regulator-fixed";
> +		regulator-name = "vph_pwr";
> +		regulator-min-microvolt = <3700000>;
> +		regulator-max-microvolt = <3700000>;
> +		regulator-always-on;
> +		regulator-boot-on;
> +	};
> +};
> +
> +&blsp_i2c3 {
> +	status = "okay";
> +
> +	touchscreen@38 {
> +		compatible = "edt,edt-ft5306";
> +		reg = <0x38>;
> +		interrupt-parent = <&tlmm>;
> +		interrupts = <65 0x2008>;
> +		reset-gpios = <&tlmm 64 GPIO_ACTIVE_LOW>;
> +		vcc-supply = <&pm8937_l10>;
> +		iovcc-supply = <&pm8937_l5>;
> +
> +		touchscreen-size-x = <720>;
> +		touchscreen-size-y = <1280>;
> +	};
> +};
> +
> +&blsp_i2c5 {
> +	status = "okay";
> +
> +	bq27426@55 {
> +		compatible = "ti,bq27426";
> +		reg = <0x55>;
> +		monitored-battery = <&battery>;
> +	};
> +
> +	bq25601@6b{
> +		compatible = "ti,bq25601";
> +		reg = <0x6b>;
> +		monitored-battery = <&battery>;
> +
> +		interrupt-parent = <&tlmm>;
> +		interrupts = <61 IRQ_TYPE_EDGE_FALLING>;
> +
> +		input-voltage-limit-microvolt = <4400000>;
> +		input-current-limit-microamp = <1000000>;
> +	};
> +};
> +
> +&pm8937_resin {
> +	linux,code = <KEY_VOLUMEDOWN>;
> +	status = "okay";
> +};
> +
> +&pm8937_spmi_regulators {
> +	pm8937_s5: s5 {

Which regulator is this?

> +		regulator-min-microvolt = <1050000>;
> +		regulator-max-microvolt = <1350000>;
> +		regulator-always-on;
> +		regulator-boot-on;
> +	};
> +};
> +

[..]

> +
> +&wcnss {
> +	vddpx-supply = <&pm8937_l5>;
> +	status = "okay";
> +

rogue empty line

> +};
> +
> +&wcnss_iris {
> +	compatible = "qcom,wcn3620";
> +	vddxo-supply = <&pm8937_l7>;
> +	vddrfa-supply = <&pm8937_l19>;
> +	vddpa-supply = <&pm8937_l9>;
> +	vdddig-supply = <&pm8937_l5>;
> +};
> +
> +&wcnss_mem {
> +	status = "okay";
> +};
> 
> -- 
> 2.47.0
> 

-- 
With best wishes
Dmitry

Re: [PATCH RFC 14/14] arm64: dts: qcom: Add Xiaomi Redmi 5A

[barnabas.czeman]

On 2024-10-19 15:48, Dmitry Baryshkov wrote:
> On Sat, Oct 19, 2024 at 01:50:51PM +0200, Barnabás Czémán wrote:
>> Add initial support for Xiaomi Redmi 5A (riva).
>> 
>> Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
>> ---
>>  arch/arm64/boot/dts/qcom/Makefile                |   1 +
>>  arch/arm64/boot/dts/qcom/msm8917-xiaomi-riva.dts | 295 
>> +++++++++++++++++++++++
>>  2 files changed, 296 insertions(+)
>> 
>> diff --git a/arch/arm64/boot/dts/qcom/Makefile 
>> b/arch/arm64/boot/dts/qcom/Makefile
>> index 
>> 065bb19481c16db2affd291826d420c83a89c52a..79add0e07d8a5f3362d70b0aaaaa9b8c48e31239 
>> 100644
>> --- a/arch/arm64/boot/dts/qcom/Makefile
>> +++ b/arch/arm64/boot/dts/qcom/Makefile
>> @@ -59,6 +59,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= 
>> msm8916-wingtech-wt86518.dtb
>>  dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-wingtech-wt86528.dtb
>>  dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-wingtech-wt88047.dtb
>>  dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-yiming-uz801v3.dtb
>> +dtb-$(CONFIG_ARCH_QCOM)	+= msm8917-xiaomi-riva.dtb
>>  dtb-$(CONFIG_ARCH_QCOM)	+= msm8929-wingtech-wt82918hd.dtb
>>  dtb-$(CONFIG_ARCH_QCOM)	+= msm8939-huawei-kiwi.dtb
>>  dtb-$(CONFIG_ARCH_QCOM)	+= msm8939-longcheer-l9100.dtb
>> diff --git a/arch/arm64/boot/dts/qcom/msm8917-xiaomi-riva.dts 
>> b/arch/arm64/boot/dts/qcom/msm8917-xiaomi-riva.dts
>> new file mode 100644
>> index 
>> 0000000000000000000000000000000000000000..7553f73603fc87797b0d424a2af6f2da65c90f5f
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/qcom/msm8917-xiaomi-riva.dts
>> @@ -0,0 +1,295 @@
>> +// SPDX-License-Identifier: BSD-3-Clause
>> +/*
>> + * Copyright (c) 2023, Barnabas Czeman
>> + */
>> +
>> +/dts-v1/;
>> +
>> +#include <dt-bindings/arm/qcom,ids.h>
>> +#include <dt-bindings/gpio/gpio.h>
>> +#include <dt-bindings/input/linux-event-codes.h>
>> +#include <dt-bindings/leds/common.h>
>> +#include "msm8917.dtsi"
>> +#include "pm8937.dtsi"
>> +
>> +/ {
>> +	model = "Xiaomi Redmi 5A (riva)";
>> +	compatible = "xiaomi,riva", "qcom,msm8917";
>> +	chassis-type = "handset";
>> +
>> +	qcom,msm-id = <QCOM_ID_MSM8917 0>;
>> +	qcom,board-id = <0x1000b 2>, <0x2000b 2>;
> 
> Is this required to boot?
Yes
> 
>> +
>> +	battery: battery {
>> +		compatible = "simple-battery";
>> +		charge-full-design-microamp-hours = <3000000>;
>> +		energy-full-design-microwatt-hours = <11500000>;
>> +		constant-charge-current-max-microamp = <1000000>;
>> +		constant-charge-voltage-max-microvolt = <4400000>;
>> +		precharge-current-microamp = <256000>;
>> +		charge-term-current-microamp = <60000>;
>> +		voltage-min-design-microvolt = <3400000>;
>> +	};
>> +
>> +	chosen {
>> +		#address-cells = <2>;
>> +		#size-cells = <2>;
>> +		ranges;
>> +
>> +		stdout-path = "framebuffer0";
>> +
>> +		framebuffer0: framebuffer@90001000 {
>> +			compatible = "simple-framebuffer";
>> +			reg = <0x0 0x90001000 0x0 (720 * 1280 * 3)>;
>> +			width = <720>;
>> +			height = <1280>;
>> +			stride = <(720 * 3)>;
>> +			format = "r8g8b8";
>> +
>> +			clocks = <&gcc GCC_MDSS_AHB_CLK>,
>> +				 <&gcc GCC_MDSS_AXI_CLK>,
>> +				 <&gcc GCC_MDSS_VSYNC_CLK>,
>> +				 <&gcc GCC_MDSS_MDP_CLK>,
>> +				 <&gcc GCC_MDSS_BYTE0_CLK>,
>> +				 <&gcc GCC_MDSS_PCLK0_CLK>,
>> +				 <&gcc GCC_MDSS_ESC0_CLK>;
>> +			power-domains = <&gcc MDSS_GDSC>;
>> +		};
>> +	};
>> +
>> +	gpio-keys {
>> +		compatible = "gpio-keys";
>> +
>> +		key-volup {
>> +			label = "Volume Up";
>> +			linux,code = <KEY_VOLUMEUP>;
>> +			gpios = <&tlmm 91 GPIO_ACTIVE_LOW>;
>> +			debounce-interval = <15>;
>> +		};
>> +	};
>> +
>> +	reserved-memory {
>> +		/delete-node/ reserved@85b00000;
>> +		qseecom_mem: reserved@84a00000 {
>> +			reg = <0x0 0x84a00000 0x0 0x1900000>;
>> +			no-map;
>> +		};
>> +
>> +		framebuffer_mem: memory@90001000 {
>> +			reg = <0x0 0x90001000 0x0 (720 * 1280 * 3)>;
>> +			no-map;
>> +		};
>> +	};
>> +
>> +	vph_pwr: vph-pwr-regulator {
> 
> regulator-vph-pwr, please
> 
>> +		compatible = "regulator-fixed";
>> +		regulator-name = "vph_pwr";
>> +		regulator-min-microvolt = <3700000>;
>> +		regulator-max-microvolt = <3700000>;
>> +		regulator-always-on;
>> +		regulator-boot-on;
>> +	};
>> +};
>> +
>> +&blsp_i2c3 {
>> +	status = "okay";
>> +
>> +	touchscreen@38 {
>> +		compatible = "edt,edt-ft5306";
>> +		reg = <0x38>;
>> +		interrupt-parent = <&tlmm>;
>> +		interrupts = <65 0x2008>;
>> +		reset-gpios = <&tlmm 64 GPIO_ACTIVE_LOW>;
>> +		vcc-supply = <&pm8937_l10>;
>> +		iovcc-supply = <&pm8937_l5>;
>> +
>> +		touchscreen-size-x = <720>;
>> +		touchscreen-size-y = <1280>;
>> +	};
>> +};
>> +
>> +&blsp_i2c5 {
>> +	status = "okay";
>> +
>> +	bq27426@55 {
>> +		compatible = "ti,bq27426";
>> +		reg = <0x55>;
>> +		monitored-battery = <&battery>;
>> +	};
>> +
>> +	bq25601@6b{
>> +		compatible = "ti,bq25601";
>> +		reg = <0x6b>;
>> +		monitored-battery = <&battery>;
>> +
>> +		interrupt-parent = <&tlmm>;
>> +		interrupts = <61 IRQ_TYPE_EDGE_FALLING>;
>> +
>> +		input-voltage-limit-microvolt = <4400000>;
>> +		input-current-limit-microamp = <1000000>;
>> +	};
>> +};
>> +
>> +&pm8937_resin {
>> +	linux,code = <KEY_VOLUMEDOWN>;
>> +	status = "okay";
>> +};
>> +
>> +&pm8937_spmi_regulators {
>> +	pm8937_s5: s5 {
> 
> Which regulator is this?
> 
>> +		regulator-min-microvolt = <1050000>;
>> +		regulator-max-microvolt = <1350000>;
>> +		regulator-always-on;
>> +		regulator-boot-on;
>> +	};
>> +};
>> +
> 
> [..]
> 
>> +
>> +&wcnss {
>> +	vddpx-supply = <&pm8937_l5>;
>> +	status = "okay";
>> +
> 
> rogue empty line
> 
>> +};
>> +
>> +&wcnss_iris {
>> +	compatible = "qcom,wcn3620";
>> +	vddxo-supply = <&pm8937_l7>;
>> +	vddrfa-supply = <&pm8937_l19>;
>> +	vddpa-supply = <&pm8937_l9>;
>> +	vdddig-supply = <&pm8937_l5>;
>> +};
>> +
>> +&wcnss_mem {
>> +	status = "okay";
>> +};
>> 
>> --
>> 2.47.0
>> 

Re: [PATCH RFC 12/14] arm64: dts: qcom: Add initial support for MSM8917

[barnabas.czeman]

On 2024-10-19 15:43, Dmitry Baryshkov wrote:
> On Sat, Oct 19, 2024 at 01:50:49PM +0200, Barnabás Czémán wrote:
>> From: Otto Pflüger <otto.pflueger@abscue.de>
>> 
>> Add initial support for MSM8917 SoC.
>> 
>> Signed-off-by: Otto Pflüger <otto.pflueger@abscue.de>
>> [reword commit, rebase, fix schema errors]
>> Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
>> ---
>>  arch/arm64/boot/dts/qcom/msm8917-pins.dtsi |  344 ++++++
>>  arch/arm64/boot/dts/qcom/msm8917.dtsi      | 1557 
>> ++++++++++++++++++++++++++++
>>  arch/arm64/boot/dts/qcom/pm8916.dtsi       |    9 +-
>>  3 files changed, 1909 insertions(+), 1 deletion(-)
>> 
>> diff --git a/arch/arm64/boot/dts/qcom/msm8917-pins.dtsi 
>> b/arch/arm64/boot/dts/qcom/msm8917-pins.dtsi
>> new file mode 100644
>> index 
>> 0000000000000000000000000000000000000000..f283ffd59b8aca8e510ef95d5526af9592a1c036
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/qcom/msm8917-pins.dtsi
> 
> Please merge into msm8917.dtsi (for generic parts) and
> msm8917-boatd.dtsi (for board-specific parts).
> 
>> @@ -0,0 +1,344 @@
>> +// SPDX-License-Identifier: GPL-2.0
> 
> If possible, GPL-2.0 OR MIT, or GPL-2.0 OR BSD-2/3-Clause
> 
>> +&tlmm {
>> +	blsp1_uart1_default: blsp1-uart1-default-state {
>> +		pins = "gpio0", "gpio1", "gpio2", "gpio3";
>> +		function = "blsp_uart1";
>> +
>> +		drive-strength = <16>;
>> +		bias-disable;
>> +	};
>> +
>> +	blsp1_uart1_sleep: blsp1-uart1-sleep-state {
>> +		pins = "gpio0", "gpio1", "gpio2", "gpio3";
>> +		function = "gpio";
>> +
>> +		drive-strength = <2>;
>> +		bias-pull-down;
>> +	};
> 
> Please sort all the pin states by the node name.
> 
>> +
>> +	wcnss_pin_a: wcnss-active-state {
>> +		wcss-wlan2-pins {
>> +			pins = "gpio76";
>> +			function = "wcss_wlan2";
>> +			drive-strength = <6>;
>> +			bias-pull-up;
>> +
>> +		};
>> +
>> +		wcss-wlan1-pins {
> 
> and subnodes too.
> 
>> +			pins = "gpio77";
>> +			function = "wcss_wlan1";
>> +			drive-strength = <6>;
>> +			bias-pull-up;
>> +
>> +		};
>> +
>> +		wcss-wlan0-pins {
>> +			pins = "gpio78";
>> +			function = "wcss_wlan0";
>> +			drive-strength = <6>;
>> +			bias-pull-up;
>> +
>> +		};
>> +
>> +		wcss-wlan-pins {
>> +			pins = "gpio79", "gpio80";
>> +			function = "wcss_wlan";
>> +			drive-strength = <6>;
>> +			bias-pull-up;
>> +
>> +		};
>> +	};
>> +
>> +	cci0_default: cci0-default-state {
>> +		pins = "gpio29", "gpio30";
>> +		function = "cci_i2c";
>> +
>> +
>> +		drive-strength = <2>;
>> +		bias-disable;
>> +	};
>> +
>> +	cci1_default: cci1-default-state {
>> +		pins = "gpio31", "gpio32";
>> +		function = "cci_i2c";
>> +
>> +
>> +		drive-strength = <2>;
>> +		bias-disable;
>> +	};
>> +
>> +	cdc_pdm_lines_act: pdm-lines-on-state {
>> +		pins = "gpio69", "gpio70", "gpio71", "gpio72",
>> +		       "gpio73", "gpio74";
>> +		function = "cdc_pdm0";
>> +
>> +		drive-strength = <8>;
>> +		bias-disable;
>> +	};
>> +
>> +	cdc_pdm_lines_sus: pdm-lines-off-state {
>> +		pins = "gpio69", "gpio70", "gpio71", "gpio72",
>> +		       "gpio73", "gpio74";
>> +		function = "cdc_pdm0";
>> +
>> +		drive-strength = <2>;
>> +		bias-disable;
>> +	};
>> +};
>> diff --git a/arch/arm64/boot/dts/qcom/msm8917.dtsi 
>> b/arch/arm64/boot/dts/qcom/msm8917.dtsi
>> new file mode 100644
>> index 
>> 0000000000000000000000000000000000000000..e5f580c6ec28ad6442b31a0e1ee256c376c5438d
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/qcom/msm8917.dtsi
>> @@ -0,0 +1,1557 @@
>> +// SPDX-License-Identifier: GPL-2.0-only
>> +
>> +#include <dt-bindings/clock/qcom,gcc-msm8917.h>
>> +#include <dt-bindings/clock/qcom,rpmcc.h>
>> +#include <dt-bindings/interrupt-controller/arm-gic.h>
>> +#include <dt-bindings/power/qcom-rpmpd.h>
>> +#include <dt-bindings/soc/qcom,apr.h>
>> +#include <dt-bindings/sound/qcom,q6dsp-lpass-ports.h>
>> +#include <dt-bindings/thermal/thermal.h>
>> +
>> +/ {
>> +	interrupt-parent = <&intc>;
>> +
>> +	#address-cells = <2>;
>> +	#size-cells = <2>;
>> +
>> +	aliases {
>> +		mmc0 = &sdhc_1; /* SDC1 eMMC slot */
>> +		mmc1 = &sdhc_2; /* SDC2 SD card slot */
>> +	};
>> +
>> +	chosen { };
>> +
>> +	memory@80000000 {
>> +		device_type = "memory";
>> +		/* We expect the bootloader to fill in the reg */
>> +		reg = <0 0x80000000 0 0>;
>> +	};
>> +
>> +	reserved-memory {
>> +		#address-cells = <2>;
>> +		#size-cells = <2>;
>> +		ranges;
>> +
>> +		reserved@85b00000 {
>> +			reg = <0x0 0x85b00000 0x0 0x800000>;
>> +			no-map;
>> +		};
>> +
>> +		smem@86300000 {
>> +			compatible = "qcom,smem";
>> +			reg = <0x0 0x86300000 0x0 0x100000>;
>> +			no-map;
>> +
>> +			hwlocks = <&tcsr_mutex 3>;
>> +			qcom,rpm-msg-ram = <&rpm_msg_ram>;
>> +		};
>> +
>> +		reserved@86400000 {
>> +			reg = <0x0 0x86400000 0x0 0x400000>;
>> +			no-map;
>> +		};
>> +
>> +		mpss_mem: mpss@86800000 {
>> +			/*
>> +			 * The memory region for the mpss firmware is generally
>> +			 * relocatable and could be allocated dynamically.
>> +			 * However, many firmware versions tend to fail when
>> +			 * loaded to some special addresses, so it is hard to
>> +			 * define reliable alloc-ranges.
>> +			 *
>> +			 * alignment = <0x0 0x400000>;
>> +			 * alloc-ranges = <0x0 0x86800000 0x0 0x8000000>;
>> +			 */
>> +			reg = <0x0 0x86800000 0x0 0>; /* size is device-specific */
>> +			no-map;
>> +			status = "disabled";
>> +		};
>> +
>> +		adsp_mem: adsp {
>> +			size = <0x0 0x1100000>;
>> +			alignment = <0x0 0x100000>;
>> +			alloc-ranges = <0x0 0x86800000 0x0 0x8000000>;
>> +			no-map;
>> +			status = "disabled";
>> +		};
>> +
>> +		wcnss_mem: wcnss {
>> +			size = <0x0 0x700000>;
>> +			alignment = <0x0 0x100000>;
>> +			alloc-ranges = <0x0 0x86800000 0x0 0x8000000>;
>> +			no-map;
>> +			status = "disabled";
>> +		};
>> +
>> +		venus_mem: venus {
>> +			size = <0x0 0x400000>;
>> +			alignment = <0x0 0x100000>;
>> +			alloc-ranges = <0x0 0x86800000 0x0 0x8000000>;
>> +			no-map;
>> +			status = "disabled";
>> +		};
>> +
>> +		mba_mem: mba {
> 
> Please sort these nodes too.
> 
>> +			size = <0x0 0x100000>;
>> +			alignment = <0x0 0x100000>;
>> +			alloc-ranges = <0x0 0x86800000 0x0 0x8000000>;
>> +			no-map;
>> +			status = "disabled";
>> +		};
>> +
>> +		rmtfs@92100000 {
> 
> This one should be after mpss_mem, just before adsp.
> 
>> +			compatible = "qcom,rmtfs-mem";
>> +			reg = <0x0 0x92100000 0x0 0x180000>;
>> +			no-map;
>> +
>> +			qcom,client-id = <1>;
>> +		};
>> +	};
>> +
>> +	cpus {
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +
>> +		CPU0: cpu@0 {
> 
> lowercase all labels.
> 
>> +			device_type = "cpu";
>> +			compatible = "arm,cortex-a53";
>> +			reg = <0x100>;
>> +			next-level-cache = <&L2_0>;
>> +			enable-method = "psci";
>> +			clocks = <&apcs>;
>> +			operating-points-v2 = <&cpu_opp_table>;
>> +			#cooling-cells = <2>;
>> +			power-domains = <&CPU_PD0>;
>> +			power-domain-names = "psci";
>> +		};
>> +
>> +		CPU1: cpu@1 {
>> +			device_type = "cpu";
>> +			compatible = "arm,cortex-a53";
>> +			reg = <0x101>;
>> +			next-level-cache = <&L2_0>;
>> +			enable-method = "psci";
>> +			clocks = <&apcs>;
>> +			operating-points-v2 = <&cpu_opp_table>;
>> +			#cooling-cells = <2>;
>> +			power-domains = <&CPU_PD1>;
>> +			power-domain-names = "psci";
>> +		};
>> +
>> +		CPU2: cpu@2 {
>> +			device_type = "cpu";
>> +			compatible = "arm,cortex-a53";
>> +			reg = <0x102>;
>> +			next-level-cache = <&L2_0>;
>> +			enable-method = "psci";
>> +			clocks = <&apcs>;
>> +			operating-points-v2 = <&cpu_opp_table>;
>> +			#cooling-cells = <2>;
>> +			power-domains = <&CPU_PD2>;
>> +			power-domain-names = "psci";
>> +		};
>> +
>> +		CPU3: cpu@3 {
>> +			device_type = "cpu";
>> +			compatible = "arm,cortex-a53";
>> +			reg = <0x103>;
>> +			next-level-cache = <&L2_0>;
>> +			enable-method = "psci";
>> +			clocks = <&apcs>;
>> +			operating-points-v2 = <&cpu_opp_table>;
>> +			#cooling-cells = <2>;
>> +			power-domains = <&CPU_PD3>;
>> +			power-domain-names = "psci";
>> +		};
>> +
>> +		L2_0: l2-cache {
>> +			compatible = "cache";
>> +			cache-level = <2>;
>> +			cache-unified;
>> +		};
>> +
>> +		cpu-map {
>> +			cluster0 {
>> +				core0 {
>> +					cpu = <&CPU0>;
>> +				};
>> +
>> +				core1 {
>> +					cpu = <&CPU1>;
>> +				};
>> +
>> +				core2 {
>> +					cpu = <&CPU2>;
>> +				};
>> +
>> +				core3 {
>> +					cpu = <&CPU3>;
>> +				};
>> +			};
>> +		};
>> +
>> +		idle-states {
>> +			entry-method = "psci";
>> +
>> +			CPU_SLEEP_0: cpu-sleep-0 {
>> +				compatible = "arm,idle-state";
>> +				idle-state-name = "standalone-power-collapse";
>> +				arm,psci-suspend-param = <0x40000003>;
>> +				entry-latency-us = <125>;
>> +				exit-latency-us = <180>;
>> +				min-residency-us = <595>;
>> +				local-timer-stop;
>> +			};
>> +		};
>> +
>> +		domain-idle-states {
>> +			CLUSTER_PWRDN: cluster-gdhs {
>> +				compatible = "domain-idle-state";
>> +				arm,psci-suspend-param = <0x41000043>;
>> +				entry-latency-us = <240>;
>> +				exit-latency-us = <280>;
>> +				min-residency-us = <806>;
>> +			};
>> +
>> +			CLUSTER_RET: cluster-retention {
>> +				compatible = "domain-idle-state";
>> +				arm,psci-suspend-param = <0x41000023>;
>> +				entry-latency-us = <700>;
>> +				exit-latency-us = <650>;
>> +				min-residency-us = <1972>;
>> +			};
>> +
>> +			CLUSTER_PC: cluster-power-collapse {
>> +				compatible = "domain-idle-state";
>> +				arm,psci-suspend-param = <0x41000053>;
>> +				entry-latency-us = <700>;
>> +				exit-latency-us = <1000>;
>> +				min-residency-us = <6500>;
>> +			};
>> +		};
>> +	};
>> +
>> +	cpu_opp_table: opp-table-cpu {
>> +		compatible = "operating-points-v2";
>> +		opp-shared;
>> +
>> +		opp-960000000 {
>> +			opp-hz = /bits/ 64 <960000000>;
>> +		};
>> +
>> +		opp-1094400000 {
>> +			opp-hz = /bits/ 64 <1094400000>;
>> +		};
>> +
>> +		opp-1248000000 {
>> +			opp-hz = /bits/ 64 <1248000000>;
>> +		};
>> +
>> +		opp-1401600000 {
>> +			opp-hz = /bits/ 64 <1401600000>;
>> +		};
>> +	};
>> +
>> +	timer {
> 
> Again, please sort the nodes.
> 
>> +		compatible = "arm,armv8-timer";
>> +		interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | 
>> IRQ_TYPE_LEVEL_LOW)>,
>> +			     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
>> +			     <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
>> +			     <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
>> +		clock-frequency = <19200000>;
>> +	};
>> +
>> +	clocks {
>> +		xo_board: xo-board {
>> +			compatible = "fixed-clock";
>> +			#clock-cells = <0>;
>> +			clock-frequency = <19200000>;
>> +			clock-output-names = "xo";
> 
> Freq goes to the board dts.
> Please drop clock-output-names.
> 
>> +		};
>> +
>> +		sleep_clk: sleep-clk {
>> +			compatible = "fixed-clock";
>> +			#clock-cells = <0>;
>> +			clock-frequency = <32768>;
>> +			clock-output-names = "sleep_clk";
>> +		};
>> +	};
>> +
>> +	firmware {
>> +		scm: scm {
>> +			compatible = "qcom,scm-msm8916", "qcom,scm";
>> +			clocks = <&gcc GCC_CRYPTO_CLK>,
>> +				 <&gcc GCC_CRYPTO_AXI_CLK>,
>> +				 <&gcc GCC_CRYPTO_AHB_CLK>;
>> +			clock-names = "core", "bus", "iface";
>> +			#reset-cells = <1>;
>> +
>> +			qcom,dload-mode = <&tcsr 0x6100>;
>> +		};
>> +	};
>> +
>> +	pmu {
>> +		compatible = "arm,cortex-a53-pmu";
>> +		interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | 
>> IRQ_TYPE_LEVEL_HIGH)>;
>> +	};
>> +
>> +	psci {
>> +		compatible = "arm,psci-1.0";
>> +		method = "smc";
>> +
>> +		CPU_PD0: power-domain-cpu0 {
>> +			#power-domain-cells = <0>;
>> +			power-domains = <&CLUSTER_PD>;
>> +			domain-idle-states = <&CPU_SLEEP_0>;
>> +		};
>> +
>> +		CPU_PD1: power-domain-cpu1 {
>> +			#power-domain-cells = <0>;
>> +			power-domains = <&CLUSTER_PD>;
>> +			domain-idle-states = <&CPU_SLEEP_0>;
>> +		};
>> +
>> +		CPU_PD2: power-domain-cpu2 {
>> +			#power-domain-cells = <0>;
>> +			power-domains = <&CLUSTER_PD>;
>> +			domain-idle-states = <&CPU_SLEEP_0>;
>> +		};
>> +
>> +		CPU_PD3: power-domain-cpu3 {
>> +			#power-domain-cells = <0>;
>> +			power-domains = <&CLUSTER_PD>;
>> +			domain-idle-states = <&CPU_SLEEP_0>;
>> +		};
>> +
>> +		CLUSTER_PD: power-domain-cluster {
>> +			#power-domain-cells = <0>;
>> +			domain-idle-states = <&CLUSTER_PWRDN>, <&CLUSTER_RET>, 
>> <&CLUSTER_PC>;
>> +		};
>> +	};
>> +
>> +	rpm: remoteproc {
>> +		compatible = "qcom,msm8917-rpm-proc", "qcom,rpm-proc";
>> +
>> +		smd-edge {
>> +			interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
>> +			qcom,ipc = <&apcs 8 0>;
>> +			qcom,smd-edge = <15>;
>> +
>> +			rpm_requests: rpm-requests {
>> +				compatible = "qcom,rpm-msm8917", "qcom,smd-rpm";
>> +				qcom,smd-channels = "rpm_requests";
>> +
>> +				rpmcc: clock-controller {
>> +					compatible = "qcom,rpmcc-msm8917", "qcom,rpmcc";
>> +					#clock-cells = <1>;
>> +					clocks = <&xo_board>;
>> +					clock-names = "xo";
>> +				};
>> +
>> +				rpmpd: power-controller {
>> +					compatible = "qcom,msm8917-rpmpd";
>> +					#power-domain-cells = <1>;
>> +					operating-points-v2 = <&rpmpd_opp_table>;
>> +
>> +					rpmpd_opp_table: opp-table {
>> +						compatible = "operating-points-v2";
>> +
>> +						rpmpd_opp_ret: opp1 {
>> +							opp-level = <RPM_SMD_LEVEL_RETENTION>;
>> +						};
>> +
>> +						rpmpd_opp_ret_plus: opp2 {
>> +							opp-level = <RPM_SMD_LEVEL_RETENTION_PLUS>;
>> +						};
>> +
>> +						rpmpd_opp_min_svs: opp3 {
>> +							opp-level = <RPM_SMD_LEVEL_MIN_SVS>;
>> +						};
>> +
>> +						rpmpd_opp_low_svs: opp4 {
>> +							opp-level = <RPM_SMD_LEVEL_LOW_SVS>;
>> +						};
>> +
>> +						rpmpd_opp_svs: opp5 {
>> +							opp-level = <RPM_SMD_LEVEL_SVS>;
>> +						};
>> +
>> +						rpmpd_opp_svs_plus: opp6 {
>> +							opp-level = <RPM_SMD_LEVEL_SVS_PLUS>;
>> +						};
>> +
>> +						rpmpd_opp_nom: opp7 {
>> +							opp-level = <RPM_SMD_LEVEL_NOM>;
>> +						};
>> +
>> +						rpmpd_opp_nom_plus: opp8 {
>> +							opp-level = <RPM_SMD_LEVEL_NOM_PLUS>;
>> +						};
>> +
>> +						rpmpd_opp_turbo: opp9 {
>> +							opp-level = <RPM_SMD_LEVEL_TURBO>;
>> +						};
>> +					};
>> +				};
>> +			};
>> +		};
>> +	};
>> +
>> +	smp2p-adsp {
>> +		compatible = "qcom,smp2p";
>> +		qcom,smem = <443>, <429>;
>> +
>> +		interrupts = <GIC_SPI 291 IRQ_TYPE_EDGE_RISING>;
>> +
>> +		mboxes = <&apcs 10>;
>> +
>> +		qcom,local-pid = <0>;
>> +		qcom,remote-pid = <2>;
>> +
>> +		adsp_smp2p_out: master-kernel {
>> +			qcom,entry-name = "master-kernel";
>> +
>> +			#qcom,smem-state-cells = <1>;
>> +		};
>> +
>> +		adsp_smp2p_in: slave-kernel {
>> +			qcom,entry-name = "slave-kernel";
>> +
>> +			interrupt-controller;
>> +			#interrupt-cells = <2>;
>> +		};
>> +	};
>> +
>> +	smp2p-modem {
>> +		compatible = "qcom,smp2p";
>> +		qcom,smem = <435>, <428>;
>> +
>> +		interrupts = <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>;
>> +
>> +		qcom,ipc = <&apcs 8 14>;
>> +
>> +		qcom,local-pid = <0>;
>> +		qcom,remote-pid = <1>;
>> +
>> +		modem_smp2p_out: master-kernel {
>> +			qcom,entry-name = "master-kernel";
>> +
>> +			#qcom,smem-state-cells = <1>;
>> +		};
>> +
>> +		modem_smp2p_in: slave-kernel {
>> +			qcom,entry-name = "slave-kernel";
>> +
>> +			interrupt-controller;
>> +			#interrupt-cells = <2>;
>> +		};
>> +	};
>> +
>> +	smp2p-wcnss {
>> +		compatible = "qcom,smp2p";
>> +		qcom,smem = <451>, <431>;
>> +
>> +		interrupts = <GIC_SPI 143 IRQ_TYPE_EDGE_RISING>;
>> +
>> +		qcom,ipc = <&apcs 8 18>;
>> +
>> +		qcom,local-pid = <0>;
>> +		qcom,remote-pid = <4>;
>> +
>> +		wcnss_smp2p_out: master-kernel {
>> +			qcom,entry-name = "master-kernel";
>> +
>> +			#qcom,smem-state-cells = <1>;
>> +		};
>> +
>> +		wcnss_smp2p_in: slave-kernel {
>> +			qcom,entry-name = "slave-kernel";
>> +
>> +			interrupt-controller;
>> +			#interrupt-cells = <2>;
>> +		};
>> +	};
>> +
>> +	smsm {
>> +		compatible = "qcom,smsm";
>> +
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +
>> +		qcom,ipc-1 = <&apcs 8 13>;
>> +		qcom,ipc-3 = <&apcs 8 19>;
> 
> Please use mboxes instead
> 
>> +
>> +		apps_smsm: apps@0 {
>> +			reg = <0>;
>> +
>> +			#qcom,smem-state-cells = <1>;
>> +		};
>> +
>> +		hexagon_smsm: hexagon@1 {
>> +			reg = <1>;
>> +			interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
>> +
>> +			interrupt-controller;
>> +			#interrupt-cells = <2>;
>> +		};
>> +
>> +		wcnss_smsm: wcnss@6 {
>> +			reg = <6>;
>> +			interrupts = <GIC_SPI 144 IRQ_TYPE_EDGE_RISING>;
>> +
>> +			interrupt-controller;
>> +			#interrupt-cells = <2>;
>> +		};
>> +	};
>> +
>> +	soc: soc@0 {
>> +		#address-cells = <1>;
>> +		#size-cells = <1>;
>> +		ranges = <0 0 0 0xffffffff>;
>> +		compatible = "simple-bus";
>> +
>> +		rng@22000 {
>> +			compatible = "qcom,prng";
>> +			reg = <0xe3000 0x1000>;
>> +			clocks = <&gcc GCC_PRNG_AHB_CLK>;
>> +			clock-names = "core";
>> +		};
>> +
>> +		restart@4ab000 {
>> +			compatible = "qcom,pshold";
>> +			reg = <0x004ab000 0x4>;
>> +		};
>> +
>> +		qfprom: qfprom@a4000 {
>> +			compatible = "qcom,msm8917-qfprom", "qcom,qfprom";
>> +			reg = <0x000a4000 0x1000>;
>> +			#address-cells = <1>;
>> +			#size-cells = <1>;
> 
> empty line
> 
>> +			tsens_caldata: caldata@d0 {
>> +				reg = <0x01d8 0x14>;
>> +			};
> 
> No, individual bit definitions for each of tsens fuse values.
> 
>> +		};
>> +
>> +		rpm_msg_ram: sram@60000 {
>> +			compatible = "qcom,rpm-msg-ram";
>> +			reg = <0x00060000 0x8000>;
>> +		};
>> +
>> +		tsens: thermal-sensor@4a9000 {
>> +			compatible = "qcom,msm8917-tsens", "qcom,tsens-v1";
>> +			reg = <0x004a9000 0x1000>,
>> +			      <0x004a8000 0x1000>;
>> +			nvmem-cells = <&tsens_caldata>;
>> +			nvmem-cell-names = "calib";
> 
> And here too, individual bits instead of a single blob.
> 
>> +			#qcom,sensors = <10>;
>> +			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
>> +			interrupt-names = "uplow";
>> +			#thermal-sensor-cells = <1>;
>> +		};
>> +
>> +		tlmm: pinctrl@1000000 {
>> +			compatible = "qcom,msm8917-pinctrl";
>> +			reg = <0x01000000 0x300000>;
>> +			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
>> +			gpio-controller;
>> +			gpio-ranges = <&tlmm 0 0 134>;
>> +			#gpio-cells = <2>;
>> +			interrupt-controller;
>> +			#interrupt-cells = <2>;
>> +		};
>> +
>> +		gcc: clock-controller@1800000 {
>> +			compatible = "qcom,gcc-msm8917";
>> +			#clock-cells = <1>;
>> +			#reset-cells = <1>;
>> +			#power-domain-cells = <1>;
>> +			reg = <0x01800000 0x80000>;
>> +			clocks = <&xo_board>,
>> +				 <&sleep_clk>,
>> +				 <&mdss_dsi0_phy 1>,
>> +				 <&mdss_dsi0_phy 0>;
>> +			clock-names = "xo",
>> +				      "sleep_clk",
>> +				      "dsi0pll",
>> +				      "dsi0pllbyte";
>> +		};
>> +
>> +		tcsr_mutex: hwlock@1905000 {
>> +			compatible = "qcom,tcsr-mutex";
>> +			reg = <0x01905000 0x20000>;
>> +			#hwlock-cells = <1>;
>> +		};
>> +
>> +		tcsr: syscon@1937000 {
>> +			compatible = "qcom,tcsr-msm8917", "syscon";
>> +			reg = <0x01937000 0x30000>;
>> +		};
>> +
>> +		apps_iommu: iommu@1e00000 {
>> +			#address-cells = <1>;
>> +			#size-cells = <1>;
>> +			#iommu-cells = <1>;
>> +			compatible = "qcom,msm8917-iommu", "qcom,msm-iommu-v1";
>> +			ranges = <0 0x01e20000 0x20000>;
>> +
>> +			clocks = <&gcc GCC_SMMU_CFG_CLK>,
>> +				 <&gcc GCC_APSS_TCU_CLK>;
>> +			clock-names = "iface", "bus";
>> +
>> +			qcom,iommu-secure-id = <17>;
>> +
>> +			/* VFE */
>> +			iommu-ctx@14000 {
>> +				compatible = "qcom,msm-iommu-v1-ns";
>> +				reg = <0x00014000 0x1000>;
>> +				interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
>> +			};
>> +
>> +			/* MDP_0 */
>> +			iommu-ctx@15000 {
>> +				compatible = "qcom,msm-iommu-v1-ns";
>> +				reg = <0x00015000 0x1000>;
>> +				interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
>> +			};
>> +
>> +			/* VENUS_NS */
>> +			iommu-ctx@16000 {
>> +				compatible = "qcom,msm-iommu-v1-ns";
>> +				reg = <0x00016000 0x1000>;
>> +				interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
>> +			};
>> +		};
>> +
>> +		gpu_iommu: iommu@1f00000 {
>> +			#address-cells = <1>;
>> +			#size-cells = <1>;
>> +			#iommu-cells = <1>;
>> +
>> +			compatible = "qcom,msm8917-iommu", "qcom,msm-iommu-v1";
>> +
>> +			ranges = <0 0x01f08000 0x10000>;
>> +			clocks = <&gcc GCC_SMMU_CFG_CLK>,
>> +				 <&gcc GCC_GFX_TCU_CLK>;
>> +			clock-names = "iface", "bus";
>> +			qcom,iommu-secure-id = <18>;
>> +
>> +			iommu-ctx@0 {
>> +				compatible = "qcom,msm-iommu-v2-ns";
>> +				reg = <0x0000 0x1000>;
>> +				interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>;
>> +			};
>> +		};
>> +
>> +		mdss: display-subsystem@1a00000 {
> 
> Please keep the nodes sorted by the address.
> 
>> +			compatible = "qcom,mdss";
>> +			reg = <0x01a00000 0x1000>,
>> +			      <0x01ab0000 0x1040>;
>> +			reg-names = "mdss_phys", "vbif_phys";
>> +
>> +			power-domains = <&gcc MDSS_GDSC>;
>> +
>> +			clocks = <&gcc GCC_MDSS_AHB_CLK>,
>> +				 <&gcc GCC_MDSS_AXI_CLK>,
>> +				 <&gcc GCC_MDSS_VSYNC_CLK>;
>> +			clock-names = "iface",
>> +				      "bus",
>> +				      "vsync";
>> +
>> +			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
>> +
>> +			interrupt-controller;
>> +			#interrupt-cells = <1>;
>> +
>> +			#address-cells = <1>;
>> +			#size-cells = <1>;
>> +			ranges;
>> +
>> +			status = "disabled";
>> +
>> +			mdp: display-controller@1a01000 {
>> +				compatible = "qcom,msm8917-mdp5", "qcom,mdp5";
>> +				reg = <0x01a01000 0x89000>;
>> +				reg-names = "mdp_phys";
>> +
>> +				interrupt-parent = <&mdss>;
>> +				interrupts = <0>;
>> +
>> +				power-domains = <&gcc MDSS_GDSC>;
>> +
>> +				clocks = <&gcc GCC_MDSS_AHB_CLK>,
>> +					 <&gcc GCC_MDSS_AXI_CLK>,
>> +					 <&gcc GCC_MDSS_MDP_CLK>,
>> +					 <&gcc GCC_MDSS_VSYNC_CLK>;
>> +				clock-names = "iface",
>> +					      "bus",
>> +					      "core",
>> +					      "vsync";
>> +
>> +				iommus = <&apps_iommu 0x15>;
>> +
>> +				ports {
>> +					#address-cells = <1>;
>> +					#size-cells = <0>;
>> +
>> +					port@0 {
>> +						reg = <0>;
> 
> Please add missing empty lines between properties and subnodes.
> 
>> +						mdp5_intf1_out: endpoint {
> 
> mdss_mdp_intf1_out:
> 
>> +							remote-endpoint = <&mdss_dsi0_in>;
>> +						};
>> +					};
>> +				};
>> +			};
>> +
>> +			mdss_dsi0: dsi@1a94000 {
>> +				compatible = "qcom,mdss-dsi-ctrl";
>> +				reg = <0x01a94000 0x300>;
>> +				reg-names = "dsi_ctrl";
>> +
>> +				interrupt-parent = <&mdss>;
>> +				interrupts = <4>;
>> +
>> +				assigned-clocks = <&gcc BYTE0_CLK_SRC>,
>> +						  <&gcc PCLK0_CLK_SRC>;
>> +				assigned-clock-parents = <&mdss_dsi0_phy 0>,
>> +							 <&mdss_dsi0_phy 1>;
>> +
>> +				clocks = <&gcc GCC_MDSS_MDP_CLK>,
>> +					 <&gcc GCC_MDSS_AHB_CLK>,
>> +					 <&gcc GCC_MDSS_AXI_CLK>,
>> +					 <&gcc GCC_MDSS_BYTE0_CLK>,
>> +					 <&gcc GCC_MDSS_PCLK0_CLK>,
>> +					 <&gcc GCC_MDSS_ESC0_CLK>;
>> +				clock-names = "mdp_core",
>> +					      "iface",
>> +					      "bus",
>> +					      "byte",
>> +					      "pixel",
>> +					      "core";
>> +				phys = <&mdss_dsi0_phy>;
>> +
>> +				operating-points-v2 = <&mdss_dsi0_opp_table>;
>> +				power-domains = <&rpmpd MSM8917_VDDCX>;
>> +
>> +				#address-cells = <1>;
>> +				#size-cells = <0>;
>> +
>> +				ports {
>> +					#address-cells = <1>;
>> +					#size-cells = <0>;
>> +
>> +					port@0 {
>> +						reg = <0>;
>> +						mdss_dsi0_in: endpoint {
>> +							remote-endpoint = <&mdp5_intf1_out>;
>> +						};
>> +					};
>> +
>> +					port@1 {
>> +						reg = <1>;
>> +						mdss_dsi0_out: endpoint {
>> +						};
>> +					};
>> +				};
>> +
>> +				mdss_dsi0_opp_table: opp-table {
>> +					compatible = "operating-points-v2";
>> +
>> +					opp-125000000 {
>> +						opp-hz = /bits/ 64 <125000000>;
>> +						required-opps = <&rpmpd_opp_svs>;
>> +					};
>> +
>> +					opp-187500000 {
>> +						opp-hz = /bits/ 64 <187500000>;
>> +						required-opps = <&rpmpd_opp_nom>;
>> +					};
>> +				};
>> +			};
>> +
>> +			mdss_dsi0_phy: phy@1a94400 {
>> +				compatible = "qcom,dsi-phy-28nm-8937";
>> +				reg = <0x01a94a00 0xd4>,
>> +				      <0x01a94400 0x280>,
>> +				      <0x01a94b80 0x30>;
>> +				reg-names = "dsi_pll",
>> +					    "dsi_phy",
>> +					    "dsi_phy_regulator";
>> +
>> +				#clock-cells = <1>;
>> +				#phy-cells = <0>;
>> +
>> +				clocks = <&gcc GCC_MDSS_AHB_CLK>,
>> +					 <&xo_board>;
>> +				clock-names = "iface", "ref";
>> +			};
>> +		};
>> +
>> +		a53pll: clock@b016000 {
>> +			compatible = "qcom,msm8939-a53pll";
>> +			reg = <0x0b016000 0x40>;
>> +			clocks = <&xo_board>;
>> +			clock-names = "xo";
>> +			#clock-cells = <0>;
>> +			operating-points-v2 = <&pll_opp_table>;
>> +
>> +			pll_opp_table: opp-table {
>> +				compatible = "operating-points-v2";
>> +
>> +				opp-960000000 {
>> +					opp-hz = /bits/ 64 <960000000>;
>> +				};
>> +
>> +				opp-1094400000 {
>> +					opp-hz = /bits/ 64 <1094400000>;
>> +				};
>> +
>> +				opp-1248000000 {
>> +					opp-hz = /bits/ 64 <1248000000>;
>> +				};
>> +
>> +				opp-1401600000 {
>> +				      opp-hz = /bits/ 64 <1401600000>;
>> +				};
>> +			};
>> +		};
>> +
>> +		gpu: gpu@1c00000 {
>> +			compatible = "qcom,adreno-306.32", "qcom,adreno";
> 
> Is it really .32 ?
> 
>> +			reg = <0x01c00000 0x20000>;
>> +			reg-names = "kgsl_3d0_reg_memory";
>> +			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
>> +			interrupt-names = "kgsl_3d0_irq";
>> +			clock-names = "core",
>> +				      "iface",
>> +				      "mem_iface",
>> +				      "alt_mem_iface",
>> +				      "gfx3d";
>> +			clocks = <&gcc GCC_OXILI_GFX3D_CLK>,
>> +				 <&gcc GCC_OXILI_AHB_CLK>,
>> +				 <&gcc GCC_BIMC_GFX_CLK>,
>> +				 <&gcc GCC_BIMC_GPU_CLK>,
>> +				 <&gcc GFX3D_CLK_SRC>;
>> +			power-domains = <&gcc OXILI_GX_GDSC>;
>> +			operating-points-v2 = <&gpu_opp_table>;
>> +			#cooling-cells = <2>;
>> +
>> +			iommus = <&gpu_iommu 0>;
>> +
>> +			status = "disabled";
>> +
>> +			gpu_opp_table: opp-table {
>> +				compatible = "operating-points-v2";
>> +
>> +				opp-598000000 {
>> +					opp-hz = /bits/ 64 <598000000>;
>> +				};
>> +
>> +				opp-523200000 {
>> +					opp-hz = /bits/ 64 <523200000>;
>> +				};
>> +
>> +				opp-484800000 {
>> +					opp-hz = /bits/ 64 <484800000>;
>> +				};
>> +
>> +				opp-400000000 {
>> +					opp-hz = /bits/ 64 <400000000>;
>> +				};
>> +
>> +				opp-270000000 {
>> +					opp-hz = /bits/ 64 <270000000>;
>> +				};
>> +
>> +				opp-19200000 {
>> +					opp-hz = /bits/ 64 <19200000>;
>> +				};
>> +			};
>> +		};
>> +
>> +		spmi_bus: spmi@200f000 {
>> +			compatible = "qcom,spmi-pmic-arb";
>> +			reg = <0x0200f000 0x001000>,
>> +			      <0x02400000 0x800000>,
>> +			      <0x02c00000 0x800000>,
>> +			      <0x03800000 0x200000>,
>> +			      <0x0200a000 0x002100>;
>> +			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
>> +			interrupt-names = "periph_irq";
>> +			interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
>> +			qcom,ee = <0>;
>> +			qcom,channel = <0>;
>> +			#address-cells = <2>;
>> +			#size-cells = <0>;
>> +			interrupt-controller;
>> +			#interrupt-cells = <4>;
>> +		};
>> +
>> +		bam_dmux_dma: dma-controller@4044000 {
>> +			compatible = "qcom,bam-v1.7.0";
>> +			reg = <0x04044000 0x19000>;
>> +			interrupts = <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>;
>> +			#dma-cells = <1>;
>> +			qcom,ee = <0>;
>> +
>> +			num-channels = <6>;
>> +			qcom,num-ees = <1>;
>> +			qcom,powered-remotely;
>> +
>> +			status = "disabled";
>> +		};
>> +
>> +		apcs: mailbox@b011000 {
>> +			compatible = "qcom,msm8939-apcs-kpss-global", "syscon";
>> +			reg = <0x0b011000 0x1000>;
>> +			#mbox-cells = <1>;
>> +			clocks = <&a53pll>, <&gcc GPLL0_EARLY>, <&rpmcc 
>> RPM_SMD_XO_CLK_SRC>;
>> +			clock-names = "pll", "aux", "ref";
>> +			#clock-cells = <0>;
>> +		};
>> +
>> +		sdhc_1: mmc@7824900 {
>> +			compatible = "qcom,sdhci-msm-v4";
>> +			reg = <0x07824900 0x500>, <0x07824000 0x800>;
>> +			reg-names = "hc", "core";
>> +
>> +			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
>> +				     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
>> +			interrupt-names = "hc_irq", "pwr_irq";
>> +			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
>> +				 <&gcc GCC_SDCC1_APPS_CLK>,
>> +				 <&xo_board>;
>> +			clock-names = "iface", "core", "xo";
>> +			power-domains = <&rpmpd MSM8917_VDDCX>;
>> +			mmc-hs200-1_8v;
>> +			mmc-hs400-1_8v;
>> +			mmc-ddr-1_8v;
>> +			bus-width = <8>;
>> +			non-removable;
>> +			status = "disabled";
>> +		};
>> +
>> +		sdhc_2: mmc@7864900 {
>> +			compatible = "qcom,sdhci-msm-v4";
>> +			reg = <0x07864900 0x500>, <0x07864000 0x800>;
>> +			reg-names = "hc", "core";
>> +
>> +			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
>> +				     <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
>> +			interrupt-names = "hc_irq", "pwr_irq";
>> +			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
>> +				 <&gcc GCC_SDCC2_APPS_CLK>,
>> +				 <&xo_board>;
>> +			clock-names = "iface", "core", "xo";
>> +			power-domains = <&rpmpd MSM8917_VDDCX>;
>> +			bus-width = <4>;
>> +			status = "disabled";
>> +		};
>> +
>> +		blsp1_dma: dma-controller@7884000 {
>> +			compatible = "qcom,bam-v1.7.0";
>> +			reg = <0x07884000 0x1f000>;
>> +			interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&gcc GCC_BLSP1_AHB_CLK>;
>> +			clock-names = "bam_clk";
>> +			qcom,controlled-remotely;
>> +			#dma-cells = <1>;
>> +			num-channels = <12>;
>> +			qcom,num-ees = <4>;
>> +			qcom,ee = <0>;
>> +		};
>> +
>> +		blsp2_dma: dma-controller@7ac4000 {
>> +			compatible = "qcom,bam-v1.7.0";
>> +			reg = <0x07ac4000 0x1d000>;
>> +			interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&gcc GCC_BLSP2_AHB_CLK>;
>> +			clock-names = "bam_clk";
>> +			qcom,controlled-remotely;
>> +			#dma-cells = <1>;
>> +			num-channels = <10>;
>> +			qcom,num-ees = <4>;
>> +			qcom,ee = <0>;
>> +		};
>> +
>> +		blsp1_uart1: serial@78af000 {
>> +			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
>> +			reg = <0x078af000 0x200>;
>> +			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>,
>> +				 <&gcc GCC_BLSP1_AHB_CLK>;
>> +			clock-names = "core", "iface";
>> +			dmas = <&blsp1_dma 0>, <&blsp1_dma 1>;
>> +			dma-names = "tx", "rx";
>> +			pinctrl-names = "default", "sleep";
>> +			pinctrl-0 = <&blsp1_uart1_default>;
>> +			pinctrl-1 = <&blsp1_uart1_sleep>;
>> +			status = "disabled";
>> +		};
>> +
>> +		blsp1_uart2: serial@78b0000 {
>> +			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
>> +			reg = <0x078b0000 0x200>;
>> +			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>,
>> +				 <&gcc GCC_BLSP1_AHB_CLK>;
>> +			clock-names = "core", "iface";
>> +			dmas = <&blsp1_dma 2>, <&blsp1_dma 3>;
>> +			dma-names = "tx", "rx";
>> +			pinctrl-names = "default", "sleep";
>> +			pinctrl-0 = <&blsp1_uart2_default>;
>> +			pinctrl-1 = <&blsp1_uart2_sleep>;
>> +			status = "disabled";
>> +		};
>> +
>> +		blsp_i2c2: i2c@78b6000 {
>> +			compatible = "qcom,i2c-qup-v2.2.1";
>> +			reg = <0x078b6000 0x600>;
>> +			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
>> +				 <&gcc GCC_BLSP1_AHB_CLK>;
>> +			clock-names = "core", "iface";
>> +			dmas = <&blsp1_dma 6>, <&blsp1_dma 7>;
>> +			dma-names = "tx", "rx";
>> +			pinctrl-names = "default", "sleep";
>> +			pinctrl-0 = <&i2c2_default>;
>> +			pinctrl-1 = <&i2c2_sleep>;
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			status = "disabled";
>> +		};
>> +
>> +		blsp_i2c3: i2c@78b7000 {
>> +			compatible = "qcom,i2c-qup-v2.2.1";
>> +			reg = <0x078b7000 0x600>;
>> +			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
>> +				 <&gcc GCC_BLSP1_AHB_CLK>;
>> +			clock-names = "core", "iface";
>> +			dmas = <&blsp1_dma 8>, <&blsp1_dma 9>;
>> +			dma-names = "tx", "rx";
>> +			pinctrl-names = "default", "sleep";
>> +			pinctrl-0 = <&i2c3_default>;
>> +			pinctrl-1 = <&i2c3_sleep>;
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			status = "disabled";
>> +		};
>> +
>> +		blsp_spi3: spi@78b7000 {
>> +			compatible = "qcom,spi-qup-v2.2.1";
>> +			reg = <0x078b7000 0x600>;
>> +			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&gcc GCC_BLSP1_QUP3_SPI_APPS_CLK>,
>> +				 <&gcc GCC_BLSP1_AHB_CLK>;
>> +			clock-names = "core", "iface";
>> +			dmas = <&blsp1_dma 8>, <&blsp1_dma 9>;
>> +			dma-names = "tx", "rx";
>> +			pinctrl-names = "default", "sleep";
>> +			pinctrl-0 = <&spi3_default>;
>> +			pinctrl-1 = <&spi3_sleep>;
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			status = "disabled";
>> +		};
>> +
>> +		blsp_i2c4: i2c@78b8000 {
>> +			compatible = "qcom,i2c-qup-v2.2.1";
>> +			reg = <0x078b8000 0x500>;
>> +			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>,
>> +				 <&gcc GCC_BLSP1_AHB_CLK>;
>> +			clock-names = "core", "iface";
>> +			dmas = <&blsp1_dma 10>, <&blsp1_dma 11>;
>> +			dma-names = "tx", "rx";
>> +			pinctrl-names = "default", "sleep";
>> +			pinctrl-0 = <&i2c4_default>;
>> +			pinctrl-1 = <&i2c4_sleep>;
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			status = "disabled";
>> +		};
>> +
>> +		blsp_i2c5: i2c@7af5000 {
>> +			compatible = "qcom,i2c-qup-v2.2.1";
>> +			reg = <0x07af5000 0x600>;
>> +			interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>,
>> +				 <&gcc GCC_BLSP2_AHB_CLK>;
>> +			clock-names = "core", "iface";
>> +			dmas = <&blsp2_dma 4>, <&blsp2_dma 5>;
>> +			dma-names = "tx", "rx";
>> +			pinctrl-names = "default", "sleep";
>> +			pinctrl-0 = <&i2c5_default>;
>> +			pinctrl-1 = <&i2c5_sleep>;
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			status = "disabled";
>> +		};
>> +
>> +		blsp_spi6: spi@7af6000 {
>> +			compatible = "qcom,spi-qup-v2.2.1";
>> +			reg = <0x07af6000 0x600>;
>> +			interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&gcc GCC_BLSP2_QUP2_SPI_APPS_CLK>,
>> +				 <&gcc GCC_BLSP2_AHB_CLK>;
>> +			clock-names = "core", "iface";
>> +			dmas = <&blsp2_dma 6>, <&blsp2_dma 7>;
>> +			dma-names = "tx", "rx";
>> +			pinctrl-names = "default", "sleep";
>> +			pinctrl-0 = <&spi6_default>;
>> +			pinctrl-1 = <&spi6_sleep>;
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			status = "disabled";
>> +		};
>> +
>> +		usb_hs_phy: phy@6c000 {
>> +			compatible = "qcom,usb-hs-28nm-femtophy";
>> +			reg = <0x6c000 0x200>;
>> +			#phy-cells = <0>;
>> +			clocks = <&xo_board>,
>> +				 <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>,
>> +				 <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
>> +			clock-names = "ref", "ahb", "sleep";
>> +			resets = <&gcc GCC_QUSB2_PHY_BCR>,
>> +				 <&gcc GCC_USB2_HS_PHY_ONLY_BCR>;
>> +			reset-names = "phy", "por";
>> +			status = "disabled";
>> +		};
>> +
>> +		usb: usb@78db000 {
>> +			compatible = "qcom,ci-hdrc";
>> +			reg = <0x078db000 0x200>,
>> +			      <0x078db200 0x200>;
>> +			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
>> +				     <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&gcc GCC_USB_HS_AHB_CLK>,
>> +				 <&gcc GCC_USB_HS_SYSTEM_CLK>;
>> +			clock-names = "iface", "core";
>> +			assigned-clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>;
>> +			assigned-clock-rates = <80000000>;
>> +			resets = <&gcc GCC_USB_HS_BCR>;
>> +			reset-names = "core";
>> +			phy_type = "ulpi";
>> +			dr_mode = "otg";
>> +			hnp-disable;
>> +			srp-disable;
>> +			adp-disable;
>> +			ahb-burst-config = <0>;
>> +			phy-names = "usb-phy";
>> +			phys = <&usb_hs_phy>;
>> +			status = "disabled";
>> +			#reset-cells = <1>;
>> +		};
>> +
>> +		pronto: wcnss: remoteproc@a21b000 {
> 
> One label should be enough.
> 
>> +			compatible = "qcom,pronto-v3-pil", "qcom,pronto";
>> +			reg = <0x0a204000 0x2000>, <0x0a202000 0x1000>, <0x0a21b000 
>> 0x3000>;
>> +			reg-names = "ccu", "dxe", "pmu";
>> +
>> +			memory-region = <&wcnss_mem>;
>> +
>> +			interrupts-extended = <&intc GIC_SPI 149 IRQ_TYPE_EDGE_RISING>,
>> +					      <&wcnss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
>> +					      <&wcnss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
>> +					      <&wcnss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
>> +					      <&wcnss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
>> +			interrupt-names = "wdog", "fatal", "ready", "handover", 
>> "stop-ack";
>> +
>> +			power-domains = <&rpmpd MSM8917_VDDCX>,
>> +					<&rpmpd MSM8917_VDDMX>;
>> +			power-domain-names = "cx", "mx";
>> +
>> +			qcom,smem-states = <&wcnss_smp2p_out 0>;
>> +			qcom,smem-state-names = "stop";
>> +
>> +			pinctrl-names = "default";
>> +			pinctrl-0 = <&wcnss_pin_a>;
>> +
>> +			status = "disabled";
>> +
>> +			wcnss_iris: iris {
>> +				clocks = <&rpmcc RPM_SMD_RF_CLK2>;
>> +				clock-names = "xo";
>> +			};
>> +
>> +			smd-edge {
>> +				interrupts = <GIC_SPI 142 IRQ_TYPE_EDGE_RISING>;
>> +
>> +				qcom,ipc = <&apcs 8 17>;
> 
> mboxes
> 
>> +				qcom,smd-edge = <6>;
>> +				qcom,remote-pid = <4>;
>> +
>> +				label = "pronto";
>> +
>> +				wcnss_ctrl: wcnss {
>> +					compatible = "qcom,wcnss";
>> +					qcom,smd-channels = "WCNSS_CTRL";
>> +
>> +					qcom,mmio = <&pronto>;
>> +
>> +					wcnss_bt: bluetooth {
>> +						compatible = "qcom,wcnss-bt";
>> +					};
>> +
>> +					wcnss_wifi: wifi {
>> +						compatible = "qcom,wcnss-wlan";
>> +
>> +						interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
>> +							     <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
>> +						interrupt-names = "tx", "rx";
>> +
>> +						qcom,smem-states = <&apps_smsm 10>, <&apps_smsm 9>;
>> +						qcom,smem-state-names = "tx-enable",
>> +									"tx-rings-empty";
>> +					};
>> +				};
>> +			};
>> +		};
>> +
>> +		intc: interrupt-controller@b000000 {
>> +			compatible = "qcom,msm-qgic2";
>> +			interrupt-controller;
>> +			#interrupt-cells = <3>;
>> +			reg = <0x0b000000 0x1000>,
>> +			      <0x0b002000 0x1000>;
>> +		};
>> +
>> +		watchdog@b017000 {
>> +			compatible = "qcom,apss-wdt-qcs404", "qcom,kpss-wdt";
>> +			reg = <0x0b017000 0x1000>;
>> +			clocks = <&sleep_clk>;
>> +		};
>> +
>> +		timer@b120000 {
>> +			#address-cells = <1>;
>> +			#size-cells = <1>;
>> +			ranges;
>> +			compatible = "arm,armv7-timer-mem";
>> +			reg = <0x0b120000 0x1000>;
>> +			clock-frequency = <19200000>;
>> +
>> +			frame@b121000 {
>> +				frame-number = <0>;
>> +				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
>> +					     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
>> +				reg = <0x0b121000 0x1000>,
>> +				      <0x0b122000 0x1000>;
>> +			};
>> +
>> +			frame@b123000 {
>> +				frame-number = <1>;
>> +				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
>> +				reg = <0x0b123000 0x1000>;
>> +				status = "disabled";
>> +			};
>> +
>> +			frame@b124000 {
>> +				frame-number = <2>;
>> +				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
>> +				reg = <0x0b124000 0x1000>;
>> +				status = "disabled";
>> +			};
>> +
>> +			frame@b125000 {
>> +				frame-number = <3>;
>> +				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
>> +				reg = <0x0b125000 0x1000>;
>> +				status = "disabled";
>> +			};
>> +
>> +			frame@b126000 {
>> +				frame-number = <4>;
>> +				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
>> +				reg = <0x0b126000 0x1000>;
>> +				status = "disabled";
>> +			};
>> +
>> +			frame@b127000 {
>> +				frame-number = <5>;
>> +				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
>> +				reg = <0x0b127000 0x1000>;
>> +				status = "disabled";
>> +			};
>> +
>> +			frame@b128000 {
>> +				frame-number = <6>;
>> +				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
>> +				reg = <0x0b128000 0x1000>;
>> +				status = "disabled";
>> +			};
>> +		};
>> +	};
>> +
>> +	thermal_zones: thermal-zones {
>> +		aoss-thermal {
>> +			polling-delay-passive = <250>;
>> +			polling-delay = <1000>;
>> +
>> +			thermal-sensors = <&tsens 0>;
>> +
>> +			trips {
>> +				aoss_alert0: trip-point0 {
>> +					temperature = <85000>;
>> +					hysteresis = <2000>;
>> +					type = "hot";
>> +				};
>> +			};
>> +		};
>> +
>> +		mdm-core-thermal {
>> +			polling-delay-passive = <250>;
>> +			polling-delay = <1000>;
>> +
>> +			thermal-sensors = <&tsens 1>;
>> +
>> +			trips {
>> +				mdm_core_alert0: trip-point0 {
>> +					temperature = <85000>;
>> +					hysteresis = <2000>;
>> +					type = "hot";
>> +				};
>> +			};
>> +		};
>> +
>> +		q6-thermal {
>> +			polling-delay-passive = <250>;
>> +			polling-delay = <1000>;
>> +
>> +			thermal-sensors = <&tsens 2>;
>> +
>> +			trips {
>> +				q6_alert0: trip-point0 {
>> +					temperature = <85000>;
>> +					hysteresis = <2000>;
>> +					type = "hot";
>> +				};
>> +			};
>> +		};
>> +
>> +		camera-thermal {
>> +			polling-delay-passive = <250>;
>> +			polling-delay = <1000>;
>> +
>> +			thermal-sensors = <&tsens 3>;
>> +
>> +			trips {
>> +				camera_alert0: trip-point0 {
>> +					temperature = <85000>;
>> +					hysteresis = <2000>;
>> +					type = "hot";
>> +				};
>> +			};
>> +		};
>> +
>> +		cpuss1-thermal {
>> +			polling-delay-passive = <250>;
>> +			polling-delay = <1000>;
>> +
>> +			thermal-sensors = <&tsens 4>;
>> +
>> +			trips {
>> +				cpuss1_alert0: trip-point0 {
>> +					temperature = <75000>;
>> +					hysteresis = <2000>;
>> +					type = "passive";
>> +				};
>> +
>> +				cpuss1_alert1: trip-point1 {
>> +					temperature = <85000>;
>> +					hysteresis = <2000>;
>> +					type = "hot";
>> +				};
>> +
>> +				cpuss1_crit: cpuss1-crit {
>> +					temperature = <100000>;
>> +					hysteresis = <2000>;
>> +					type = "critical";
>> +				};
>> +			};
>> +			cooling-maps {
>> +				map0 {
>> +					trip = <&cpuss1_alert0>;
>> +					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>> +							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>> +							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>> +							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>> +				};
>> +			};
>> +		};
>> +
>> +		cpu0-thermal {
>> +			polling-delay-passive = <250>;
>> +			polling-delay = <1000>;
>> +
>> +			thermal-sensors = <&tsens 5>;
>> +
>> +			trips {
>> +				cpu0_alert0: trip-point0 {
>> +					temperature = <75000>;
>> +					hysteresis = <2000>;
>> +					type = "passive";
>> +				};
>> +
>> +				cpu0_alert1: trip-point1 {
>> +					temperature = <85000>;
>> +					hysteresis = <2000>;
>> +					type = "hot";
>> +				};
>> +
>> +				cpu0_crit: cpu-crit {
>> +					temperature = <100000>;
>> +					hysteresis = <2000>;
>> +					type = "critical";
>> +				};
>> +			};
>> +			cooling-maps {
>> +				map0 {
>> +					trip = <&cpu0_alert1>;
>> +					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>> +							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>> +							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>> +							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>> +				};
>> +			};
>> +		};
>> +
>> +		cpu1-thermal {
>> +			polling-delay-passive = <250>;
>> +			polling-delay = <1000>;
>> +
>> +			thermal-sensors = <&tsens 6>;
>> +
>> +			trips {
>> +				cpu1_alert0: trip-point0 {
>> +					temperature = <75000>;
>> +					hysteresis = <2000>;
>> +					type = "hot";
>> +				};
>> +
>> +				cpu1_alert1: trip-point1 {
>> +					temperature = <85000>;
>> +					hysteresis = <2000>;
>> +					type = "passive";
>> +				};
>> +
>> +				cpu1_crit: cpu-crit {
>> +					temperature = <100000>;
>> +					hysteresis = <2000>;
>> +					type = "critical";
>> +				};
>> +			};
>> +			cooling-maps {
>> +				map0 {
>> +					trip = <&cpu1_alert1>;
>> +					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>> +							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>> +							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>> +							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>> +				};
>> +			};
>> +		};
>> +
>> +		cpu2-thermal {
>> +			polling-delay-passive = <250>;
>> +			polling-delay = <1000>;
>> +
>> +			thermal-sensors = <&tsens 7>;
>> +
>> +			trips {
>> +				cpu2_alert0: trip-point0 {
>> +					temperature = <75000>;
>> +					hysteresis = <2000>;
>> +					type = "hot";
>> +				};
>> +
>> +				cpu2_alert1: trip-point1 {
>> +					temperature = <85000>;
>> +					hysteresis = <2000>;
>> +					type = "passive";
>> +				};
>> +
>> +				cpu2_crit: cpu-crit {
>> +					temperature = <100000>;
>> +					hysteresis = <2000>;
>> +					type = "critical";
>> +				};
>> +			};
>> +			cooling-maps {
>> +				map0 {
>> +					trip = <&cpu2_alert1>;
>> +					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>> +							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>> +							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>> +							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>> +				};
>> +			};
>> +		};
>> +
>> +		cpu3-thermal {
>> +			polling-delay-passive = <250>;
>> +			polling-delay = <1000>;
>> +
>> +			thermal-sensors = <&tsens 8>;
>> +
>> +			trips {
>> +				cpu3_alert0: trip-point0 {
>> +					temperature = <75000>;
>> +					hysteresis = <2000>;
>> +					type = "hot";
>> +				};
>> +
>> +				cpu3_alert1: trip-point1 {
>> +					temperature = <85000>;
>> +					hysteresis = <2000>;
>> +					type = "passive";
>> +				};
>> +
>> +				cpu3_crit: cpu-crit {
>> +					temperature = <100000>;
>> +					hysteresis = <2000>;
>> +					type = "critical";
>> +				};
>> +			};
>> +			cooling-maps {
>> +				map0 {
>> +					trip = <&cpu3_alert1>;
>> +					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>> +							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>> +							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>> +							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>> +				};
>> +			};
>> +		};
>> +
>> +		gpu-thermal {
>> +			polling-delay-passive = <250>;
>> +			polling-delay = <1000>;
>> +
>> +			thermal-sensors = <&tsens 9>;
>> +
>> +			trips {
>> +				gpu_alert: trip-point0 {
>> +					temperature = <70000>;
>> +					hysteresis = <2000>;
>> +					type = "passive";
>> +				};
>> +
>> +				gpu_crit: gpu-crit {
>> +					temperature = <90000>;
>> +					hysteresis = <2000>;
>> +					type = "critical";
>> +				};
>> +			};
>> +
>> +			cooling-maps {
>> +				map0 {
>> +					trip = <&gpu_alert>;
>> +					cooling-device = <&gpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>> +				};
>> +			};
>> +		};
>> +	};
>> +};
>> +
>> +#include "msm8917-pins.dtsi"
>> diff --git a/arch/arm64/boot/dts/qcom/pm8916.dtsi 
>> b/arch/arm64/boot/dts/qcom/pm8916.dtsi
>> index 
>> f8e4829ff7f7de1f1f4f5da0f41020875d6c7e17..df0f679250ccb6c49a76288fad12f67b01fa6b61 
>> 100644
>> --- a/arch/arm64/boot/dts/qcom/pm8916.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/pm8916.dtsi
> 
> Separate commit, please. Or move this to the board file submission.
It is a lefover what i have not notice, i will remove it from the 
commit.
> 
>> @@ -47,7 +47,7 @@ pon@800 {
>>  			mode-bootloader = <0x2>;
>>  			mode-recovery = <0x1>;
>> 
>> -			pwrkey {
>> +			pm8916_pwrkey: pwrkey {
>>  				compatible = "qcom,pm8941-pwrkey";
>>  				interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
>>  				debounce = <15625>;
>> @@ -210,6 +210,10 @@ pm8916_pwm: pwm {
>>  			status = "disabled";
>>  		};
>> 
>> +		pm8916_spmi_regulators: regulators {
>> +			compatible = "qcom,pm8916-regulators";
>> +		};
>> +
>>  		pm8916_vib: vibrator@c000 {
>>  			compatible = "qcom,pm8916-vib";
>>  			reg = <0xc000>;
>> @@ -219,6 +223,9 @@ pm8916_vib: vibrator@c000 {
>>  		pm8916_codec: audio-codec@f000 {
>>  			compatible = "qcom,pm8916-wcd-analog-codec";
>>  			reg = <0xf000>;
>> +			reg-names = "pmic-codec-core";
>> +			clocks = <&xo_board>;
>> +			clock-names = "mclk";
> 
> Why? Is this compatible with other boards?
> 
>>  			interrupt-parent = <&spmi_bus>;
>>  			interrupts = <0x1 0xf0 0x0 IRQ_TYPE_NONE>,
>>  				     <0x1 0xf0 0x1 IRQ_TYPE_NONE>,
>> 
>> --
>> 2.47.0
>> 

Re: [PATCH RFC 14/14] arm64: dts: qcom: Add Xiaomi Redmi 5A

[Dmitry Baryshkov]

On Sat, Oct 19, 2024 at 03:57:54PM +0200, barnabas.czeman@mainlining.org wrote:
> On 2024-10-19 15:48, Dmitry Baryshkov wrote:
> > On Sat, Oct 19, 2024 at 01:50:51PM +0200, Barnabás Czémán wrote:
> > > Add initial support for Xiaomi Redmi 5A (riva).
> > > 
> > > Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
> > > ---
> > >  arch/arm64/boot/dts/qcom/Makefile                |   1 +
> > >  arch/arm64/boot/dts/qcom/msm8917-xiaomi-riva.dts | 295
> > > +++++++++++++++++++++++
> > >  2 files changed, 296 insertions(+)
> > > 
> > > diff --git a/arch/arm64/boot/dts/qcom/Makefile
> > > b/arch/arm64/boot/dts/qcom/Makefile
> > > index 065bb19481c16db2affd291826d420c83a89c52a..79add0e07d8a5f3362d70b0aaaaa9b8c48e31239
> > > 100644
> > > --- a/arch/arm64/boot/dts/qcom/Makefile
> > > +++ b/arch/arm64/boot/dts/qcom/Makefile
> > > @@ -59,6 +59,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+=
> > > msm8916-wingtech-wt86518.dtb
> > >  dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-wingtech-wt86528.dtb
> > >  dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-wingtech-wt88047.dtb
> > >  dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-yiming-uz801v3.dtb
> > > +dtb-$(CONFIG_ARCH_QCOM)	+= msm8917-xiaomi-riva.dtb
> > >  dtb-$(CONFIG_ARCH_QCOM)	+= msm8929-wingtech-wt82918hd.dtb
> > >  dtb-$(CONFIG_ARCH_QCOM)	+= msm8939-huawei-kiwi.dtb
> > >  dtb-$(CONFIG_ARCH_QCOM)	+= msm8939-longcheer-l9100.dtb
> > > diff --git a/arch/arm64/boot/dts/qcom/msm8917-xiaomi-riva.dts
> > > b/arch/arm64/boot/dts/qcom/msm8917-xiaomi-riva.dts
> > > new file mode 100644
> > > index 0000000000000000000000000000000000000000..7553f73603fc87797b0d424a2af6f2da65c90f5f
> > > --- /dev/null
> > > +++ b/arch/arm64/boot/dts/qcom/msm8917-xiaomi-riva.dts
> > > @@ -0,0 +1,295 @@
> > > +// SPDX-License-Identifier: BSD-3-Clause
> > > +/*
> > > + * Copyright (c) 2023, Barnabas Czeman
> > > + */
> > > +
> > > +/dts-v1/;
> > > +
> > > +#include <dt-bindings/arm/qcom,ids.h>
> > > +#include <dt-bindings/gpio/gpio.h>
> > > +#include <dt-bindings/input/linux-event-codes.h>
> > > +#include <dt-bindings/leds/common.h>
> > > +#include "msm8917.dtsi"
> > > +#include "pm8937.dtsi"
> > > +
> > > +/ {
> > > +	model = "Xiaomi Redmi 5A (riva)";
> > > +	compatible = "xiaomi,riva", "qcom,msm8917";
> > > +	chassis-type = "handset";
> > > +
> > > +	qcom,msm-id = <QCOM_ID_MSM8917 0>;
> > > +	qcom,board-id = <0x1000b 2>, <0x2000b 2>;
> > 
> > Is this required to boot?
> Yes

Hmm, did you verify the dts against DT bindings? I think you need to fix
them.


-- 
With best wishes
Dmitry

Re: [PATCH RFC 14/14] arm64: dts: qcom: Add Xiaomi Redmi 5A

[Dmitry Baryshkov]

On Sat, 19 Oct 2024 at 17:38, Dmitry Baryshkov
<dmitry.baryshkov@linaro.org> wrote:
>
> On Sat, Oct 19, 2024 at 03:57:54PM +0200, barnabas.czeman@mainlining.org wrote:
> > On 2024-10-19 15:48, Dmitry Baryshkov wrote:
> > > On Sat, Oct 19, 2024 at 01:50:51PM +0200, Barnabás Czémán wrote:
> > > > Add initial support for Xiaomi Redmi 5A (riva).
> > > >
> > > > Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
> > > > ---
> > > >  arch/arm64/boot/dts/qcom/Makefile                |   1 +
> > > >  arch/arm64/boot/dts/qcom/msm8917-xiaomi-riva.dts | 295
> > > > +++++++++++++++++++++++
> > > >  2 files changed, 296 insertions(+)
> > > >
> > > > diff --git a/arch/arm64/boot/dts/qcom/Makefile
> > > > b/arch/arm64/boot/dts/qcom/Makefile
> > > > index 065bb19481c16db2affd291826d420c83a89c52a..79add0e07d8a5f3362d70b0aaaaa9b8c48e31239
> > > > 100644
> > > > --- a/arch/arm64/boot/dts/qcom/Makefile
> > > > +++ b/arch/arm64/boot/dts/qcom/Makefile
> > > > @@ -59,6 +59,7 @@ dtb-$(CONFIG_ARCH_QCOM) +=
> > > > msm8916-wingtech-wt86518.dtb
> > > >  dtb-$(CONFIG_ARCH_QCOM)  += msm8916-wingtech-wt86528.dtb
> > > >  dtb-$(CONFIG_ARCH_QCOM)  += msm8916-wingtech-wt88047.dtb
> > > >  dtb-$(CONFIG_ARCH_QCOM)  += msm8916-yiming-uz801v3.dtb
> > > > +dtb-$(CONFIG_ARCH_QCOM)  += msm8917-xiaomi-riva.dtb
> > > >  dtb-$(CONFIG_ARCH_QCOM)  += msm8929-wingtech-wt82918hd.dtb
> > > >  dtb-$(CONFIG_ARCH_QCOM)  += msm8939-huawei-kiwi.dtb
> > > >  dtb-$(CONFIG_ARCH_QCOM)  += msm8939-longcheer-l9100.dtb
> > > > diff --git a/arch/arm64/boot/dts/qcom/msm8917-xiaomi-riva.dts
> > > > b/arch/arm64/boot/dts/qcom/msm8917-xiaomi-riva.dts
> > > > new file mode 100644
> > > > index 0000000000000000000000000000000000000000..7553f73603fc87797b0d424a2af6f2da65c90f5f
> > > > --- /dev/null
> > > > +++ b/arch/arm64/boot/dts/qcom/msm8917-xiaomi-riva.dts
> > > > @@ -0,0 +1,295 @@
> > > > +// SPDX-License-Identifier: BSD-3-Clause
> > > > +/*
> > > > + * Copyright (c) 2023, Barnabas Czeman
> > > > + */
> > > > +
> > > > +/dts-v1/;
> > > > +
> > > > +#include <dt-bindings/arm/qcom,ids.h>
> > > > +#include <dt-bindings/gpio/gpio.h>
> > > > +#include <dt-bindings/input/linux-event-codes.h>
> > > > +#include <dt-bindings/leds/common.h>
> > > > +#include "msm8917.dtsi"
> > > > +#include "pm8937.dtsi"
> > > > +
> > > > +/ {
> > > > + model = "Xiaomi Redmi 5A (riva)";
> > > > + compatible = "xiaomi,riva", "qcom,msm8917";
> > > > + chassis-type = "handset";
> > > > +
> > > > + qcom,msm-id = <QCOM_ID_MSM8917 0>;
> > > > + qcom,board-id = <0x1000b 2>, <0x2000b 2>;
> > >
> > > Is this required to boot?
> > Yes
>
> Hmm, did you verify the dts against DT bindings? I think you need to fix
> them.

Hmm, ignore this. You added qcom,msm8917 to the allow list in the
previous patch. Please expand the commit message there, describing
that you are enabling msm-id / board-id for this SoC, which doesn't
work otherwise.

-- 
With best wishes
Dmitry

Re: [PATCH RFC 14/14] arm64: dts: qcom: Add Xiaomi Redmi 5A

[barnabas.czeman]

On 2024-10-19 16:38, Dmitry Baryshkov wrote:
> On Sat, Oct 19, 2024 at 03:57:54PM +0200, 
> barnabas.czeman@mainlining.org wrote:
>> On 2024-10-19 15:48, Dmitry Baryshkov wrote:
>> > On Sat, Oct 19, 2024 at 01:50:51PM +0200, Barnabás Czémán wrote:
>> > > Add initial support for Xiaomi Redmi 5A (riva).
>> > >
>> > > Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
>> > > ---
>> > >  arch/arm64/boot/dts/qcom/Makefile                |   1 +
>> > >  arch/arm64/boot/dts/qcom/msm8917-xiaomi-riva.dts | 295
>> > > +++++++++++++++++++++++
>> > >  2 files changed, 296 insertions(+)
>> > >
>> > > diff --git a/arch/arm64/boot/dts/qcom/Makefile
>> > > b/arch/arm64/boot/dts/qcom/Makefile
>> > > index 065bb19481c16db2affd291826d420c83a89c52a..79add0e07d8a5f3362d70b0aaaaa9b8c48e31239
>> > > 100644
>> > > --- a/arch/arm64/boot/dts/qcom/Makefile
>> > > +++ b/arch/arm64/boot/dts/qcom/Makefile
>> > > @@ -59,6 +59,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+=
>> > > msm8916-wingtech-wt86518.dtb
>> > >  dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-wingtech-wt86528.dtb
>> > >  dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-wingtech-wt88047.dtb
>> > >  dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-yiming-uz801v3.dtb
>> > > +dtb-$(CONFIG_ARCH_QCOM)	+= msm8917-xiaomi-riva.dtb
>> > >  dtb-$(CONFIG_ARCH_QCOM)	+= msm8929-wingtech-wt82918hd.dtb
>> > >  dtb-$(CONFIG_ARCH_QCOM)	+= msm8939-huawei-kiwi.dtb
>> > >  dtb-$(CONFIG_ARCH_QCOM)	+= msm8939-longcheer-l9100.dtb
>> > > diff --git a/arch/arm64/boot/dts/qcom/msm8917-xiaomi-riva.dts
>> > > b/arch/arm64/boot/dts/qcom/msm8917-xiaomi-riva.dts
>> > > new file mode 100644
>> > > index 0000000000000000000000000000000000000000..7553f73603fc87797b0d424a2af6f2da65c90f5f
>> > > --- /dev/null
>> > > +++ b/arch/arm64/boot/dts/qcom/msm8917-xiaomi-riva.dts
>> > > @@ -0,0 +1,295 @@
>> > > +// SPDX-License-Identifier: BSD-3-Clause
>> > > +/*
>> > > + * Copyright (c) 2023, Barnabas Czeman
>> > > + */
>> > > +
>> > > +/dts-v1/;
>> > > +
>> > > +#include <dt-bindings/arm/qcom,ids.h>
>> > > +#include <dt-bindings/gpio/gpio.h>
>> > > +#include <dt-bindings/input/linux-event-codes.h>
>> > > +#include <dt-bindings/leds/common.h>
>> > > +#include "msm8917.dtsi"
>> > > +#include "pm8937.dtsi"
>> > > +
>> > > +/ {
>> > > +	model = "Xiaomi Redmi 5A (riva)";
>> > > +	compatible = "xiaomi,riva", "qcom,msm8917";
>> > > +	chassis-type = "handset";
>> > > +
>> > > +	qcom,msm-id = <QCOM_ID_MSM8917 0>;
>> > > +	qcom,board-id = <0x1000b 2>, <0x2000b 2>;
>> >
>> > Is this required to boot?
>> Yes
> 
> Hmm, did you verify the dts against DT bindings? I think you need to 
> fix
> them.
I have checked with this `make CHECK_DTBS=1 
qcom/msm8917-xiaomi-riva.dtb`

Re: [PATCH RFC 00/14] Add MSM8917/PM8937/Redmi 5A

[Krzysztof Kozlowski]

On Sat, Oct 19, 2024 at 01:50:37PM +0200, Barnabás Czémán wrote:
> This patch series add support for MSM8917 soc with PM8937 and
> Xiaomi Redmi 5A (riva).

Please always give some hint why this is not suitable for merging (you
tagged this as RFC). Every patch is for "comments", so if you mark it as
RFC means it is not ready.

Some maintainers ignore RFC patches because of that. There is a lot of
stuff here, so it's also easier for me to skip it, if this is not ready.

Best regards,
Krzysztof

Re: [PATCH RFC 12/14] arm64: dts: qcom: Add initial support for MSM8917

[barnabas.czeman]

On 2024-10-19 15:43, Dmitry Baryshkov wrote:
> On Sat, Oct 19, 2024 at 01:50:49PM +0200, Barnabás Czémán wrote:
>> From: Otto Pflüger <otto.pflueger@abscue.de>
>> 
>> Add initial support for MSM8917 SoC.
>> 
>> Signed-off-by: Otto Pflüger <otto.pflueger@abscue.de>
>> [reword commit, rebase, fix schema errors]
>> Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
>> ---
>>  arch/arm64/boot/dts/qcom/msm8917-pins.dtsi |  344 ++++++
>>  arch/arm64/boot/dts/qcom/msm8917.dtsi      | 1557 
>> ++++++++++++++++++++++++++++
>>  arch/arm64/boot/dts/qcom/pm8916.dtsi       |    9 +-
>>  3 files changed, 1909 insertions(+), 1 deletion(-)
>> 
>> diff --git a/arch/arm64/boot/dts/qcom/msm8917-pins.dtsi 
>> b/arch/arm64/boot/dts/qcom/msm8917-pins.dtsi
>> new file mode 100644
>> index 
>> 0000000000000000000000000000000000000000..f283ffd59b8aca8e510ef95d5526af9592a1c036
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/qcom/msm8917-pins.dtsi
> 
> Please merge into msm8917.dtsi (for generic parts) and
> msm8917-boatd.dtsi (for board-specific parts).
> 
>> @@ -0,0 +1,344 @@
>> +// SPDX-License-Identifier: GPL-2.0
> 
> If possible, GPL-2.0 OR MIT, or GPL-2.0 OR BSD-2/3-Clause
Unfortunatelly i cannot change the license i do not own the original 
code.
> 
>> +&tlmm {
>> +	blsp1_uart1_default: blsp1-uart1-default-state {
>> +		pins = "gpio0", "gpio1", "gpio2", "gpio3";
>> +		function = "blsp_uart1";
>> +
>> +		drive-strength = <16>;
>> +		bias-disable;
>> +	};
>> +
>> +	blsp1_uart1_sleep: blsp1-uart1-sleep-state {
>> +		pins = "gpio0", "gpio1", "gpio2", "gpio3";
>> +		function = "gpio";
>> +
>> +		drive-strength = <2>;
>> +		bias-pull-down;
>> +	};
> 
> Please sort all the pin states by the node name.
> 
>> +
>> +	wcnss_pin_a: wcnss-active-state {
>> +		wcss-wlan2-pins {
>> +			pins = "gpio76";
>> +			function = "wcss_wlan2";
>> +			drive-strength = <6>;
>> +			bias-pull-up;
>> +
>> +		};
>> +
>> +		wcss-wlan1-pins {
> 
> and subnodes too.
> 
>> +			pins = "gpio77";
>> +			function = "wcss_wlan1";
>> +			drive-strength = <6>;
>> +			bias-pull-up;
>> +
>> +		};
>> +
>> +		wcss-wlan0-pins {
>> +			pins = "gpio78";
>> +			function = "wcss_wlan0";
>> +			drive-strength = <6>;
>> +			bias-pull-up;
>> +
>> +		};
>> +
>> +		wcss-wlan-pins {
>> +			pins = "gpio79", "gpio80";
>> +			function = "wcss_wlan";
>> +			drive-strength = <6>;
>> +			bias-pull-up;
>> +
>> +		};
>> +	};
>> +
>> +	cci0_default: cci0-default-state {
>> +		pins = "gpio29", "gpio30";
>> +		function = "cci_i2c";
>> +
>> +
>> +		drive-strength = <2>;
>> +		bias-disable;
>> +	};
>> +
>> +	cci1_default: cci1-default-state {
>> +		pins = "gpio31", "gpio32";
>> +		function = "cci_i2c";
>> +
>> +
>> +		drive-strength = <2>;
>> +		bias-disable;
>> +	};
>> +
>> +	cdc_pdm_lines_act: pdm-lines-on-state {
>> +		pins = "gpio69", "gpio70", "gpio71", "gpio72",
>> +		       "gpio73", "gpio74";
>> +		function = "cdc_pdm0";
>> +
>> +		drive-strength = <8>;
>> +		bias-disable;
>> +	};
>> +
>> +	cdc_pdm_lines_sus: pdm-lines-off-state {
>> +		pins = "gpio69", "gpio70", "gpio71", "gpio72",
>> +		       "gpio73", "gpio74";
>> +		function = "cdc_pdm0";
>> +
>> +		drive-strength = <2>;
>> +		bias-disable;
>> +	};
>> +};
>> diff --git a/arch/arm64/boot/dts/qcom/msm8917.dtsi 
>> b/arch/arm64/boot/dts/qcom/msm8917.dtsi
>> new file mode 100644
>> index 
>> 0000000000000000000000000000000000000000..e5f580c6ec28ad6442b31a0e1ee256c376c5438d
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/qcom/msm8917.dtsi
>> @@ -0,0 +1,1557 @@
>> +// SPDX-License-Identifier: GPL-2.0-only
>> +
>> +#include <dt-bindings/clock/qcom,gcc-msm8917.h>
>> +#include <dt-bindings/clock/qcom,rpmcc.h>
>> +#include <dt-bindings/interrupt-controller/arm-gic.h>
>> +#include <dt-bindings/power/qcom-rpmpd.h>
>> +#include <dt-bindings/soc/qcom,apr.h>
>> +#include <dt-bindings/sound/qcom,q6dsp-lpass-ports.h>
>> +#include <dt-bindings/thermal/thermal.h>
>> +
>> +/ {
>> +	interrupt-parent = <&intc>;
>> +
>> +	#address-cells = <2>;
>> +	#size-cells = <2>;
>> +
>> +	aliases {
>> +		mmc0 = &sdhc_1; /* SDC1 eMMC slot */
>> +		mmc1 = &sdhc_2; /* SDC2 SD card slot */
>> +	};
>> +
>> +	chosen { };
>> +
>> +	memory@80000000 {
>> +		device_type = "memory";
>> +		/* We expect the bootloader to fill in the reg */
>> +		reg = <0 0x80000000 0 0>;
>> +	};
>> +
>> +	reserved-memory {
>> +		#address-cells = <2>;
>> +		#size-cells = <2>;
>> +		ranges;
>> +
>> +		reserved@85b00000 {
>> +			reg = <0x0 0x85b00000 0x0 0x800000>;
>> +			no-map;
>> +		};
>> +
>> +		smem@86300000 {
>> +			compatible = "qcom,smem";
>> +			reg = <0x0 0x86300000 0x0 0x100000>;
>> +			no-map;
>> +
>> +			hwlocks = <&tcsr_mutex 3>;
>> +			qcom,rpm-msg-ram = <&rpm_msg_ram>;
>> +		};
>> +
>> +		reserved@86400000 {
>> +			reg = <0x0 0x86400000 0x0 0x400000>;
>> +			no-map;
>> +		};
>> +
>> +		mpss_mem: mpss@86800000 {
>> +			/*
>> +			 * The memory region for the mpss firmware is generally
>> +			 * relocatable and could be allocated dynamically.
>> +			 * However, many firmware versions tend to fail when
>> +			 * loaded to some special addresses, so it is hard to
>> +			 * define reliable alloc-ranges.
>> +			 *
>> +			 * alignment = <0x0 0x400000>;
>> +			 * alloc-ranges = <0x0 0x86800000 0x0 0x8000000>;
>> +			 */
>> +			reg = <0x0 0x86800000 0x0 0>; /* size is device-specific */
>> +			no-map;
>> +			status = "disabled";
>> +		};
>> +
>> +		adsp_mem: adsp {
>> +			size = <0x0 0x1100000>;
>> +			alignment = <0x0 0x100000>;
>> +			alloc-ranges = <0x0 0x86800000 0x0 0x8000000>;
>> +			no-map;
>> +			status = "disabled";
>> +		};
>> +
>> +		wcnss_mem: wcnss {
>> +			size = <0x0 0x700000>;
>> +			alignment = <0x0 0x100000>;
>> +			alloc-ranges = <0x0 0x86800000 0x0 0x8000000>;
>> +			no-map;
>> +			status = "disabled";
>> +		};
>> +
>> +		venus_mem: venus {
>> +			size = <0x0 0x400000>;
>> +			alignment = <0x0 0x100000>;
>> +			alloc-ranges = <0x0 0x86800000 0x0 0x8000000>;
>> +			no-map;
>> +			status = "disabled";
>> +		};
>> +
>> +		mba_mem: mba {
> 
> Please sort these nodes too.
> 
>> +			size = <0x0 0x100000>;
>> +			alignment = <0x0 0x100000>;
>> +			alloc-ranges = <0x0 0x86800000 0x0 0x8000000>;
>> +			no-map;
>> +			status = "disabled";
>> +		};
>> +
>> +		rmtfs@92100000 {
> 
> This one should be after mpss_mem, just before adsp.
> 
>> +			compatible = "qcom,rmtfs-mem";
>> +			reg = <0x0 0x92100000 0x0 0x180000>;
>> +			no-map;
>> +
>> +			qcom,client-id = <1>;
>> +		};
>> +	};
>> +
>> +	cpus {
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +
>> +		CPU0: cpu@0 {
> 
> lowercase all labels.
> 
>> +			device_type = "cpu";
>> +			compatible = "arm,cortex-a53";
>> +			reg = <0x100>;
>> +			next-level-cache = <&L2_0>;
>> +			enable-method = "psci";
>> +			clocks = <&apcs>;
>> +			operating-points-v2 = <&cpu_opp_table>;
>> +			#cooling-cells = <2>;
>> +			power-domains = <&CPU_PD0>;
>> +			power-domain-names = "psci";
>> +		};
>> +
>> +		CPU1: cpu@1 {
>> +			device_type = "cpu";
>> +			compatible = "arm,cortex-a53";
>> +			reg = <0x101>;
>> +			next-level-cache = <&L2_0>;
>> +			enable-method = "psci";
>> +			clocks = <&apcs>;
>> +			operating-points-v2 = <&cpu_opp_table>;
>> +			#cooling-cells = <2>;
>> +			power-domains = <&CPU_PD1>;
>> +			power-domain-names = "psci";
>> +		};
>> +
>> +		CPU2: cpu@2 {
>> +			device_type = "cpu";
>> +			compatible = "arm,cortex-a53";
>> +			reg = <0x102>;
>> +			next-level-cache = <&L2_0>;
>> +			enable-method = "psci";
>> +			clocks = <&apcs>;
>> +			operating-points-v2 = <&cpu_opp_table>;
>> +			#cooling-cells = <2>;
>> +			power-domains = <&CPU_PD2>;
>> +			power-domain-names = "psci";
>> +		};
>> +
>> +		CPU3: cpu@3 {
>> +			device_type = "cpu";
>> +			compatible = "arm,cortex-a53";
>> +			reg = <0x103>;
>> +			next-level-cache = <&L2_0>;
>> +			enable-method = "psci";
>> +			clocks = <&apcs>;
>> +			operating-points-v2 = <&cpu_opp_table>;
>> +			#cooling-cells = <2>;
>> +			power-domains = <&CPU_PD3>;
>> +			power-domain-names = "psci";
>> +		};
>> +
>> +		L2_0: l2-cache {
>> +			compatible = "cache";
>> +			cache-level = <2>;
>> +			cache-unified;
>> +		};
>> +
>> +		cpu-map {
>> +			cluster0 {
>> +				core0 {
>> +					cpu = <&CPU0>;
>> +				};
>> +
>> +				core1 {
>> +					cpu = <&CPU1>;
>> +				};
>> +
>> +				core2 {
>> +					cpu = <&CPU2>;
>> +				};
>> +
>> +				core3 {
>> +					cpu = <&CPU3>;
>> +				};
>> +			};
>> +		};
>> +
>> +		idle-states {
>> +			entry-method = "psci";
>> +
>> +			CPU_SLEEP_0: cpu-sleep-0 {
>> +				compatible = "arm,idle-state";
>> +				idle-state-name = "standalone-power-collapse";
>> +				arm,psci-suspend-param = <0x40000003>;
>> +				entry-latency-us = <125>;
>> +				exit-latency-us = <180>;
>> +				min-residency-us = <595>;
>> +				local-timer-stop;
>> +			};
>> +		};
>> +
>> +		domain-idle-states {
>> +			CLUSTER_PWRDN: cluster-gdhs {
>> +				compatible = "domain-idle-state";
>> +				arm,psci-suspend-param = <0x41000043>;
>> +				entry-latency-us = <240>;
>> +				exit-latency-us = <280>;
>> +				min-residency-us = <806>;
>> +			};
>> +
>> +			CLUSTER_RET: cluster-retention {
>> +				compatible = "domain-idle-state";
>> +				arm,psci-suspend-param = <0x41000023>;
>> +				entry-latency-us = <700>;
>> +				exit-latency-us = <650>;
>> +				min-residency-us = <1972>;
>> +			};
>> +
>> +			CLUSTER_PC: cluster-power-collapse {
>> +				compatible = "domain-idle-state";
>> +				arm,psci-suspend-param = <0x41000053>;
>> +				entry-latency-us = <700>;
>> +				exit-latency-us = <1000>;
>> +				min-residency-us = <6500>;
>> +			};
>> +		};
>> +	};
>> +
>> +	cpu_opp_table: opp-table-cpu {
>> +		compatible = "operating-points-v2";
>> +		opp-shared;
>> +
>> +		opp-960000000 {
>> +			opp-hz = /bits/ 64 <960000000>;
>> +		};
>> +
>> +		opp-1094400000 {
>> +			opp-hz = /bits/ 64 <1094400000>;
>> +		};
>> +
>> +		opp-1248000000 {
>> +			opp-hz = /bits/ 64 <1248000000>;
>> +		};
>> +
>> +		opp-1401600000 {
>> +			opp-hz = /bits/ 64 <1401600000>;
>> +		};
>> +	};
>> +
>> +	timer {
> 
> Again, please sort the nodes.
> 
>> +		compatible = "arm,armv8-timer";
>> +		interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | 
>> IRQ_TYPE_LEVEL_LOW)>,
>> +			     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
>> +			     <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
>> +			     <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
>> +		clock-frequency = <19200000>;
>> +	};
>> +
>> +	clocks {
>> +		xo_board: xo-board {
>> +			compatible = "fixed-clock";
>> +			#clock-cells = <0>;
>> +			clock-frequency = <19200000>;
>> +			clock-output-names = "xo";
> 
> Freq goes to the board dts.
> Please drop clock-output-names.
> 
>> +		};
>> +
>> +		sleep_clk: sleep-clk {
>> +			compatible = "fixed-clock";
>> +			#clock-cells = <0>;
>> +			clock-frequency = <32768>;
>> +			clock-output-names = "sleep_clk";
>> +		};
>> +	};
>> +
>> +	firmware {
>> +		scm: scm {
>> +			compatible = "qcom,scm-msm8916", "qcom,scm";
>> +			clocks = <&gcc GCC_CRYPTO_CLK>,
>> +				 <&gcc GCC_CRYPTO_AXI_CLK>,
>> +				 <&gcc GCC_CRYPTO_AHB_CLK>;
>> +			clock-names = "core", "bus", "iface";
>> +			#reset-cells = <1>;
>> +
>> +			qcom,dload-mode = <&tcsr 0x6100>;
>> +		};
>> +	};
>> +
>> +	pmu {
>> +		compatible = "arm,cortex-a53-pmu";
>> +		interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | 
>> IRQ_TYPE_LEVEL_HIGH)>;
>> +	};
>> +
>> +	psci {
>> +		compatible = "arm,psci-1.0";
>> +		method = "smc";
>> +
>> +		CPU_PD0: power-domain-cpu0 {
>> +			#power-domain-cells = <0>;
>> +			power-domains = <&CLUSTER_PD>;
>> +			domain-idle-states = <&CPU_SLEEP_0>;
>> +		};
>> +
>> +		CPU_PD1: power-domain-cpu1 {
>> +			#power-domain-cells = <0>;
>> +			power-domains = <&CLUSTER_PD>;
>> +			domain-idle-states = <&CPU_SLEEP_0>;
>> +		};
>> +
>> +		CPU_PD2: power-domain-cpu2 {
>> +			#power-domain-cells = <0>;
>> +			power-domains = <&CLUSTER_PD>;
>> +			domain-idle-states = <&CPU_SLEEP_0>;
>> +		};
>> +
>> +		CPU_PD3: power-domain-cpu3 {
>> +			#power-domain-cells = <0>;
>> +			power-domains = <&CLUSTER_PD>;
>> +			domain-idle-states = <&CPU_SLEEP_0>;
>> +		};
>> +
>> +		CLUSTER_PD: power-domain-cluster {
>> +			#power-domain-cells = <0>;
>> +			domain-idle-states = <&CLUSTER_PWRDN>, <&CLUSTER_RET>, 
>> <&CLUSTER_PC>;
>> +		};
>> +	};
>> +
>> +	rpm: remoteproc {
>> +		compatible = "qcom,msm8917-rpm-proc", "qcom,rpm-proc";
>> +
>> +		smd-edge {
>> +			interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
>> +			qcom,ipc = <&apcs 8 0>;
>> +			qcom,smd-edge = <15>;
>> +
>> +			rpm_requests: rpm-requests {
>> +				compatible = "qcom,rpm-msm8917", "qcom,smd-rpm";
>> +				qcom,smd-channels = "rpm_requests";
>> +
>> +				rpmcc: clock-controller {
>> +					compatible = "qcom,rpmcc-msm8917", "qcom,rpmcc";
>> +					#clock-cells = <1>;
>> +					clocks = <&xo_board>;
>> +					clock-names = "xo";
>> +				};
>> +
>> +				rpmpd: power-controller {
>> +					compatible = "qcom,msm8917-rpmpd";
>> +					#power-domain-cells = <1>;
>> +					operating-points-v2 = <&rpmpd_opp_table>;
>> +
>> +					rpmpd_opp_table: opp-table {
>> +						compatible = "operating-points-v2";
>> +
>> +						rpmpd_opp_ret: opp1 {
>> +							opp-level = <RPM_SMD_LEVEL_RETENTION>;
>> +						};
>> +
>> +						rpmpd_opp_ret_plus: opp2 {
>> +							opp-level = <RPM_SMD_LEVEL_RETENTION_PLUS>;
>> +						};
>> +
>> +						rpmpd_opp_min_svs: opp3 {
>> +							opp-level = <RPM_SMD_LEVEL_MIN_SVS>;
>> +						};
>> +
>> +						rpmpd_opp_low_svs: opp4 {
>> +							opp-level = <RPM_SMD_LEVEL_LOW_SVS>;
>> +						};
>> +
>> +						rpmpd_opp_svs: opp5 {
>> +							opp-level = <RPM_SMD_LEVEL_SVS>;
>> +						};
>> +
>> +						rpmpd_opp_svs_plus: opp6 {
>> +							opp-level = <RPM_SMD_LEVEL_SVS_PLUS>;
>> +						};
>> +
>> +						rpmpd_opp_nom: opp7 {
>> +							opp-level = <RPM_SMD_LEVEL_NOM>;
>> +						};
>> +
>> +						rpmpd_opp_nom_plus: opp8 {
>> +							opp-level = <RPM_SMD_LEVEL_NOM_PLUS>;
>> +						};
>> +
>> +						rpmpd_opp_turbo: opp9 {
>> +							opp-level = <RPM_SMD_LEVEL_TURBO>;
>> +						};
>> +					};
>> +				};
>> +			};
>> +		};
>> +	};
>> +
>> +	smp2p-adsp {
>> +		compatible = "qcom,smp2p";
>> +		qcom,smem = <443>, <429>;
>> +
>> +		interrupts = <GIC_SPI 291 IRQ_TYPE_EDGE_RISING>;
>> +
>> +		mboxes = <&apcs 10>;
>> +
>> +		qcom,local-pid = <0>;
>> +		qcom,remote-pid = <2>;
>> +
>> +		adsp_smp2p_out: master-kernel {
>> +			qcom,entry-name = "master-kernel";
>> +
>> +			#qcom,smem-state-cells = <1>;
>> +		};
>> +
>> +		adsp_smp2p_in: slave-kernel {
>> +			qcom,entry-name = "slave-kernel";
>> +
>> +			interrupt-controller;
>> +			#interrupt-cells = <2>;
>> +		};
>> +	};
>> +
>> +	smp2p-modem {
>> +		compatible = "qcom,smp2p";
>> +		qcom,smem = <435>, <428>;
>> +
>> +		interrupts = <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>;
>> +
>> +		qcom,ipc = <&apcs 8 14>;
>> +
>> +		qcom,local-pid = <0>;
>> +		qcom,remote-pid = <1>;
>> +
>> +		modem_smp2p_out: master-kernel {
>> +			qcom,entry-name = "master-kernel";
>> +
>> +			#qcom,smem-state-cells = <1>;
>> +		};
>> +
>> +		modem_smp2p_in: slave-kernel {
>> +			qcom,entry-name = "slave-kernel";
>> +
>> +			interrupt-controller;
>> +			#interrupt-cells = <2>;
>> +		};
>> +	};
>> +
>> +	smp2p-wcnss {
>> +		compatible = "qcom,smp2p";
>> +		qcom,smem = <451>, <431>;
>> +
>> +		interrupts = <GIC_SPI 143 IRQ_TYPE_EDGE_RISING>;
>> +
>> +		qcom,ipc = <&apcs 8 18>;
>> +
>> +		qcom,local-pid = <0>;
>> +		qcom,remote-pid = <4>;
>> +
>> +		wcnss_smp2p_out: master-kernel {
>> +			qcom,entry-name = "master-kernel";
>> +
>> +			#qcom,smem-state-cells = <1>;
>> +		};
>> +
>> +		wcnss_smp2p_in: slave-kernel {
>> +			qcom,entry-name = "slave-kernel";
>> +
>> +			interrupt-controller;
>> +			#interrupt-cells = <2>;
>> +		};
>> +	};
>> +
>> +	smsm {
>> +		compatible = "qcom,smsm";
>> +
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +
>> +		qcom,ipc-1 = <&apcs 8 13>;
>> +		qcom,ipc-3 = <&apcs 8 19>;
> 
> Please use mboxes instead
> 
>> +
>> +		apps_smsm: apps@0 {
>> +			reg = <0>;
>> +
>> +			#qcom,smem-state-cells = <1>;
>> +		};
>> +
>> +		hexagon_smsm: hexagon@1 {
>> +			reg = <1>;
>> +			interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
>> +
>> +			interrupt-controller;
>> +			#interrupt-cells = <2>;
>> +		};
>> +
>> +		wcnss_smsm: wcnss@6 {
>> +			reg = <6>;
>> +			interrupts = <GIC_SPI 144 IRQ_TYPE_EDGE_RISING>;
>> +
>> +			interrupt-controller;
>> +			#interrupt-cells = <2>;
>> +		};
>> +	};
>> +
>> +	soc: soc@0 {
>> +		#address-cells = <1>;
>> +		#size-cells = <1>;
>> +		ranges = <0 0 0 0xffffffff>;
>> +		compatible = "simple-bus";
>> +
>> +		rng@22000 {
>> +			compatible = "qcom,prng";
>> +			reg = <0xe3000 0x1000>;
>> +			clocks = <&gcc GCC_PRNG_AHB_CLK>;
>> +			clock-names = "core";
>> +		};
>> +
>> +		restart@4ab000 {
>> +			compatible = "qcom,pshold";
>> +			reg = <0x004ab000 0x4>;
>> +		};
>> +
>> +		qfprom: qfprom@a4000 {
>> +			compatible = "qcom,msm8917-qfprom", "qcom,qfprom";
>> +			reg = <0x000a4000 0x1000>;
>> +			#address-cells = <1>;
>> +			#size-cells = <1>;
> 
> empty line
> 
>> +			tsens_caldata: caldata@d0 {
>> +				reg = <0x01d8 0x14>;
>> +			};
> 
> No, individual bit definitions for each of tsens fuse values.
> 
>> +		};
>> +
>> +		rpm_msg_ram: sram@60000 {
>> +			compatible = "qcom,rpm-msg-ram";
>> +			reg = <0x00060000 0x8000>;
>> +		};
>> +
>> +		tsens: thermal-sensor@4a9000 {
>> +			compatible = "qcom,msm8917-tsens", "qcom,tsens-v1";
>> +			reg = <0x004a9000 0x1000>,
>> +			      <0x004a8000 0x1000>;
>> +			nvmem-cells = <&tsens_caldata>;
>> +			nvmem-cell-names = "calib";
> 
> And here too, individual bits instead of a single blob.
I do not know how to do that i have only find some parts at downstream 
driver to be able to separate
the cells but i do not have every information for it.
> 
>> +			#qcom,sensors = <10>;
>> +			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
>> +			interrupt-names = "uplow";
>> +			#thermal-sensor-cells = <1>;
>> +		};
>> +
>> +		tlmm: pinctrl@1000000 {
>> +			compatible = "qcom,msm8917-pinctrl";
>> +			reg = <0x01000000 0x300000>;
>> +			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
>> +			gpio-controller;
>> +			gpio-ranges = <&tlmm 0 0 134>;
>> +			#gpio-cells = <2>;
>> +			interrupt-controller;
>> +			#interrupt-cells = <2>;
>> +		};
>> +
>> +		gcc: clock-controller@1800000 {
>> +			compatible = "qcom,gcc-msm8917";
>> +			#clock-cells = <1>;
>> +			#reset-cells = <1>;
>> +			#power-domain-cells = <1>;
>> +			reg = <0x01800000 0x80000>;
>> +			clocks = <&xo_board>,
>> +				 <&sleep_clk>,
>> +				 <&mdss_dsi0_phy 1>,
>> +				 <&mdss_dsi0_phy 0>;
>> +			clock-names = "xo",
>> +				      "sleep_clk",
>> +				      "dsi0pll",
>> +				      "dsi0pllbyte";
>> +		};
>> +
>> +		tcsr_mutex: hwlock@1905000 {
>> +			compatible = "qcom,tcsr-mutex";
>> +			reg = <0x01905000 0x20000>;
>> +			#hwlock-cells = <1>;
>> +		};
>> +
>> +		tcsr: syscon@1937000 {
>> +			compatible = "qcom,tcsr-msm8917", "syscon";
>> +			reg = <0x01937000 0x30000>;
>> +		};
>> +
>> +		apps_iommu: iommu@1e00000 {
>> +			#address-cells = <1>;
>> +			#size-cells = <1>;
>> +			#iommu-cells = <1>;
>> +			compatible = "qcom,msm8917-iommu", "qcom,msm-iommu-v1";
>> +			ranges = <0 0x01e20000 0x20000>;
>> +
>> +			clocks = <&gcc GCC_SMMU_CFG_CLK>,
>> +				 <&gcc GCC_APSS_TCU_CLK>;
>> +			clock-names = "iface", "bus";
>> +
>> +			qcom,iommu-secure-id = <17>;
>> +
>> +			/* VFE */
>> +			iommu-ctx@14000 {
>> +				compatible = "qcom,msm-iommu-v1-ns";
>> +				reg = <0x00014000 0x1000>;
>> +				interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
>> +			};
>> +
>> +			/* MDP_0 */
>> +			iommu-ctx@15000 {
>> +				compatible = "qcom,msm-iommu-v1-ns";
>> +				reg = <0x00015000 0x1000>;
>> +				interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
>> +			};
>> +
>> +			/* VENUS_NS */
>> +			iommu-ctx@16000 {
>> +				compatible = "qcom,msm-iommu-v1-ns";
>> +				reg = <0x00016000 0x1000>;
>> +				interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
>> +			};
>> +		};
>> +
>> +		gpu_iommu: iommu@1f00000 {
>> +			#address-cells = <1>;
>> +			#size-cells = <1>;
>> +			#iommu-cells = <1>;
>> +
>> +			compatible = "qcom,msm8917-iommu", "qcom,msm-iommu-v1";
>> +
>> +			ranges = <0 0x01f08000 0x10000>;
>> +			clocks = <&gcc GCC_SMMU_CFG_CLK>,
>> +				 <&gcc GCC_GFX_TCU_CLK>;
>> +			clock-names = "iface", "bus";
>> +			qcom,iommu-secure-id = <18>;
>> +
>> +			iommu-ctx@0 {
>> +				compatible = "qcom,msm-iommu-v2-ns";
>> +				reg = <0x0000 0x1000>;
>> +				interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>;
>> +			};
>> +		};
>> +
>> +		mdss: display-subsystem@1a00000 {
> 
> Please keep the nodes sorted by the address.
> 
>> +			compatible = "qcom,mdss";
>> +			reg = <0x01a00000 0x1000>,
>> +			      <0x01ab0000 0x1040>;
>> +			reg-names = "mdss_phys", "vbif_phys";
>> +
>> +			power-domains = <&gcc MDSS_GDSC>;
>> +
>> +			clocks = <&gcc GCC_MDSS_AHB_CLK>,
>> +				 <&gcc GCC_MDSS_AXI_CLK>,
>> +				 <&gcc GCC_MDSS_VSYNC_CLK>;
>> +			clock-names = "iface",
>> +				      "bus",
>> +				      "vsync";
>> +
>> +			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
>> +
>> +			interrupt-controller;
>> +			#interrupt-cells = <1>;
>> +
>> +			#address-cells = <1>;
>> +			#size-cells = <1>;
>> +			ranges;
>> +
>> +			status = "disabled";
>> +
>> +			mdp: display-controller@1a01000 {
>> +				compatible = "qcom,msm8917-mdp5", "qcom,mdp5";
>> +				reg = <0x01a01000 0x89000>;
>> +				reg-names = "mdp_phys";
>> +
>> +				interrupt-parent = <&mdss>;
>> +				interrupts = <0>;
>> +
>> +				power-domains = <&gcc MDSS_GDSC>;
>> +
>> +				clocks = <&gcc GCC_MDSS_AHB_CLK>,
>> +					 <&gcc GCC_MDSS_AXI_CLK>,
>> +					 <&gcc GCC_MDSS_MDP_CLK>,
>> +					 <&gcc GCC_MDSS_VSYNC_CLK>;
>> +				clock-names = "iface",
>> +					      "bus",
>> +					      "core",
>> +					      "vsync";
>> +
>> +				iommus = <&apps_iommu 0x15>;
>> +
>> +				ports {
>> +					#address-cells = <1>;
>> +					#size-cells = <0>;
>> +
>> +					port@0 {
>> +						reg = <0>;
> 
> Please add missing empty lines between properties and subnodes.
> 
>> +						mdp5_intf1_out: endpoint {
> 
> mdss_mdp_intf1_out:
> 
>> +							remote-endpoint = <&mdss_dsi0_in>;
>> +						};
>> +					};
>> +				};
>> +			};
>> +
>> +			mdss_dsi0: dsi@1a94000 {
>> +				compatible = "qcom,mdss-dsi-ctrl";
>> +				reg = <0x01a94000 0x300>;
>> +				reg-names = "dsi_ctrl";
>> +
>> +				interrupt-parent = <&mdss>;
>> +				interrupts = <4>;
>> +
>> +				assigned-clocks = <&gcc BYTE0_CLK_SRC>,
>> +						  <&gcc PCLK0_CLK_SRC>;
>> +				assigned-clock-parents = <&mdss_dsi0_phy 0>,
>> +							 <&mdss_dsi0_phy 1>;
>> +
>> +				clocks = <&gcc GCC_MDSS_MDP_CLK>,
>> +					 <&gcc GCC_MDSS_AHB_CLK>,
>> +					 <&gcc GCC_MDSS_AXI_CLK>,
>> +					 <&gcc GCC_MDSS_BYTE0_CLK>,
>> +					 <&gcc GCC_MDSS_PCLK0_CLK>,
>> +					 <&gcc GCC_MDSS_ESC0_CLK>;
>> +				clock-names = "mdp_core",
>> +					      "iface",
>> +					      "bus",
>> +					      "byte",
>> +					      "pixel",
>> +					      "core";
>> +				phys = <&mdss_dsi0_phy>;
>> +
>> +				operating-points-v2 = <&mdss_dsi0_opp_table>;
>> +				power-domains = <&rpmpd MSM8917_VDDCX>;
>> +
>> +				#address-cells = <1>;
>> +				#size-cells = <0>;
>> +
>> +				ports {
>> +					#address-cells = <1>;
>> +					#size-cells = <0>;
>> +
>> +					port@0 {
>> +						reg = <0>;
>> +						mdss_dsi0_in: endpoint {
>> +							remote-endpoint = <&mdp5_intf1_out>;
>> +						};
>> +					};
>> +
>> +					port@1 {
>> +						reg = <1>;
>> +						mdss_dsi0_out: endpoint {
>> +						};
>> +					};
>> +				};
>> +
>> +				mdss_dsi0_opp_table: opp-table {
>> +					compatible = "operating-points-v2";
>> +
>> +					opp-125000000 {
>> +						opp-hz = /bits/ 64 <125000000>;
>> +						required-opps = <&rpmpd_opp_svs>;
>> +					};
>> +
>> +					opp-187500000 {
>> +						opp-hz = /bits/ 64 <187500000>;
>> +						required-opps = <&rpmpd_opp_nom>;
>> +					};
>> +				};
>> +			};
>> +
>> +			mdss_dsi0_phy: phy@1a94400 {
>> +				compatible = "qcom,dsi-phy-28nm-8937";
>> +				reg = <0x01a94a00 0xd4>,
>> +				      <0x01a94400 0x280>,
>> +				      <0x01a94b80 0x30>;
>> +				reg-names = "dsi_pll",
>> +					    "dsi_phy",
>> +					    "dsi_phy_regulator";
>> +
>> +				#clock-cells = <1>;
>> +				#phy-cells = <0>;
>> +
>> +				clocks = <&gcc GCC_MDSS_AHB_CLK>,
>> +					 <&xo_board>;
>> +				clock-names = "iface", "ref";
>> +			};
>> +		};
>> +
>> +		a53pll: clock@b016000 {
>> +			compatible = "qcom,msm8939-a53pll";
>> +			reg = <0x0b016000 0x40>;
>> +			clocks = <&xo_board>;
>> +			clock-names = "xo";
>> +			#clock-cells = <0>;
>> +			operating-points-v2 = <&pll_opp_table>;
>> +
>> +			pll_opp_table: opp-table {
>> +				compatible = "operating-points-v2";
>> +
>> +				opp-960000000 {
>> +					opp-hz = /bits/ 64 <960000000>;
>> +				};
>> +
>> +				opp-1094400000 {
>> +					opp-hz = /bits/ 64 <1094400000>;
>> +				};
>> +
>> +				opp-1248000000 {
>> +					opp-hz = /bits/ 64 <1248000000>;
>> +				};
>> +
>> +				opp-1401600000 {
>> +				      opp-hz = /bits/ 64 <1401600000>;
>> +				};
>> +			};
>> +		};
>> +
>> +		gpu: gpu@1c00000 {
>> +			compatible = "qcom,adreno-306.32", "qcom,adreno";
> 
> Is it really .32 ?
Yes it is A306A (Adreno 308)
> 
>> +			reg = <0x01c00000 0x20000>;
>> +			reg-names = "kgsl_3d0_reg_memory";
>> +			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
>> +			interrupt-names = "kgsl_3d0_irq";
>> +			clock-names = "core",
>> +				      "iface",
>> +				      "mem_iface",
>> +				      "alt_mem_iface",
>> +				      "gfx3d";
>> +			clocks = <&gcc GCC_OXILI_GFX3D_CLK>,
>> +				 <&gcc GCC_OXILI_AHB_CLK>,
>> +				 <&gcc GCC_BIMC_GFX_CLK>,
>> +				 <&gcc GCC_BIMC_GPU_CLK>,
>> +				 <&gcc GFX3D_CLK_SRC>;
>> +			power-domains = <&gcc OXILI_GX_GDSC>;
>> +			operating-points-v2 = <&gpu_opp_table>;
>> +			#cooling-cells = <2>;
>> +
>> +			iommus = <&gpu_iommu 0>;
>> +
>> +			status = "disabled";
>> +
>> +			gpu_opp_table: opp-table {
>> +				compatible = "operating-points-v2";
>> +
>> +				opp-598000000 {
>> +					opp-hz = /bits/ 64 <598000000>;
>> +				};
>> +
>> +				opp-523200000 {
>> +					opp-hz = /bits/ 64 <523200000>;
>> +				};
>> +
>> +				opp-484800000 {
>> +					opp-hz = /bits/ 64 <484800000>;
>> +				};
>> +
>> +				opp-400000000 {
>> +					opp-hz = /bits/ 64 <400000000>;
>> +				};
>> +
>> +				opp-270000000 {
>> +					opp-hz = /bits/ 64 <270000000>;
>> +				};
>> +
>> +				opp-19200000 {
>> +					opp-hz = /bits/ 64 <19200000>;
>> +				};
>> +			};
>> +		};
>> +
>> +		spmi_bus: spmi@200f000 {
>> +			compatible = "qcom,spmi-pmic-arb";
>> +			reg = <0x0200f000 0x001000>,
>> +			      <0x02400000 0x800000>,
>> +			      <0x02c00000 0x800000>,
>> +			      <0x03800000 0x200000>,
>> +			      <0x0200a000 0x002100>;
>> +			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
>> +			interrupt-names = "periph_irq";
>> +			interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
>> +			qcom,ee = <0>;
>> +			qcom,channel = <0>;
>> +			#address-cells = <2>;
>> +			#size-cells = <0>;
>> +			interrupt-controller;
>> +			#interrupt-cells = <4>;
>> +		};
>> +
>> +		bam_dmux_dma: dma-controller@4044000 {
>> +			compatible = "qcom,bam-v1.7.0";
>> +			reg = <0x04044000 0x19000>;
>> +			interrupts = <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>;
>> +			#dma-cells = <1>;
>> +			qcom,ee = <0>;
>> +
>> +			num-channels = <6>;
>> +			qcom,num-ees = <1>;
>> +			qcom,powered-remotely;
>> +
>> +			status = "disabled";
>> +		};
>> +
>> +		apcs: mailbox@b011000 {
>> +			compatible = "qcom,msm8939-apcs-kpss-global", "syscon";
>> +			reg = <0x0b011000 0x1000>;
>> +			#mbox-cells = <1>;
>> +			clocks = <&a53pll>, <&gcc GPLL0_EARLY>, <&rpmcc 
>> RPM_SMD_XO_CLK_SRC>;
>> +			clock-names = "pll", "aux", "ref";
>> +			#clock-cells = <0>;
>> +		};
>> +
>> +		sdhc_1: mmc@7824900 {
>> +			compatible = "qcom,sdhci-msm-v4";
>> +			reg = <0x07824900 0x500>, <0x07824000 0x800>;
>> +			reg-names = "hc", "core";
>> +
>> +			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
>> +				     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
>> +			interrupt-names = "hc_irq", "pwr_irq";
>> +			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
>> +				 <&gcc GCC_SDCC1_APPS_CLK>,
>> +				 <&xo_board>;
>> +			clock-names = "iface", "core", "xo";
>> +			power-domains = <&rpmpd MSM8917_VDDCX>;
>> +			mmc-hs200-1_8v;
>> +			mmc-hs400-1_8v;
>> +			mmc-ddr-1_8v;
>> +			bus-width = <8>;
>> +			non-removable;
>> +			status = "disabled";
>> +		};
>> +
>> +		sdhc_2: mmc@7864900 {
>> +			compatible = "qcom,sdhci-msm-v4";
>> +			reg = <0x07864900 0x500>, <0x07864000 0x800>;
>> +			reg-names = "hc", "core";
>> +
>> +			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
>> +				     <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
>> +			interrupt-names = "hc_irq", "pwr_irq";
>> +			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
>> +				 <&gcc GCC_SDCC2_APPS_CLK>,
>> +				 <&xo_board>;
>> +			clock-names = "iface", "core", "xo";
>> +			power-domains = <&rpmpd MSM8917_VDDCX>;
>> +			bus-width = <4>;
>> +			status = "disabled";
>> +		};
>> +
>> +		blsp1_dma: dma-controller@7884000 {
>> +			compatible = "qcom,bam-v1.7.0";
>> +			reg = <0x07884000 0x1f000>;
>> +			interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&gcc GCC_BLSP1_AHB_CLK>;
>> +			clock-names = "bam_clk";
>> +			qcom,controlled-remotely;
>> +			#dma-cells = <1>;
>> +			num-channels = <12>;
>> +			qcom,num-ees = <4>;
>> +			qcom,ee = <0>;
>> +		};
>> +
>> +		blsp2_dma: dma-controller@7ac4000 {
>> +			compatible = "qcom,bam-v1.7.0";
>> +			reg = <0x07ac4000 0x1d000>;
>> +			interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&gcc GCC_BLSP2_AHB_CLK>;
>> +			clock-names = "bam_clk";
>> +			qcom,controlled-remotely;
>> +			#dma-cells = <1>;
>> +			num-channels = <10>;
>> +			qcom,num-ees = <4>;
>> +			qcom,ee = <0>;
>> +		};
>> +
>> +		blsp1_uart1: serial@78af000 {
>> +			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
>> +			reg = <0x078af000 0x200>;
>> +			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>,
>> +				 <&gcc GCC_BLSP1_AHB_CLK>;
>> +			clock-names = "core", "iface";
>> +			dmas = <&blsp1_dma 0>, <&blsp1_dma 1>;
>> +			dma-names = "tx", "rx";
>> +			pinctrl-names = "default", "sleep";
>> +			pinctrl-0 = <&blsp1_uart1_default>;
>> +			pinctrl-1 = <&blsp1_uart1_sleep>;
>> +			status = "disabled";
>> +		};
>> +
>> +		blsp1_uart2: serial@78b0000 {
>> +			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
>> +			reg = <0x078b0000 0x200>;
>> +			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>,
>> +				 <&gcc GCC_BLSP1_AHB_CLK>;
>> +			clock-names = "core", "iface";
>> +			dmas = <&blsp1_dma 2>, <&blsp1_dma 3>;
>> +			dma-names = "tx", "rx";
>> +			pinctrl-names = "default", "sleep";
>> +			pinctrl-0 = <&blsp1_uart2_default>;
>> +			pinctrl-1 = <&blsp1_uart2_sleep>;
>> +			status = "disabled";
>> +		};
>> +
>> +		blsp_i2c2: i2c@78b6000 {
>> +			compatible = "qcom,i2c-qup-v2.2.1";
>> +			reg = <0x078b6000 0x600>;
>> +			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
>> +				 <&gcc GCC_BLSP1_AHB_CLK>;
>> +			clock-names = "core", "iface";
>> +			dmas = <&blsp1_dma 6>, <&blsp1_dma 7>;
>> +			dma-names = "tx", "rx";
>> +			pinctrl-names = "default", "sleep";
>> +			pinctrl-0 = <&i2c2_default>;
>> +			pinctrl-1 = <&i2c2_sleep>;
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			status = "disabled";
>> +		};
>> +
>> +		blsp_i2c3: i2c@78b7000 {
>> +			compatible = "qcom,i2c-qup-v2.2.1";
>> +			reg = <0x078b7000 0x600>;
>> +			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
>> +				 <&gcc GCC_BLSP1_AHB_CLK>;
>> +			clock-names = "core", "iface";
>> +			dmas = <&blsp1_dma 8>, <&blsp1_dma 9>;
>> +			dma-names = "tx", "rx";
>> +			pinctrl-names = "default", "sleep";
>> +			pinctrl-0 = <&i2c3_default>;
>> +			pinctrl-1 = <&i2c3_sleep>;
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			status = "disabled";
>> +		};
>> +
>> +		blsp_spi3: spi@78b7000 {
>> +			compatible = "qcom,spi-qup-v2.2.1";
>> +			reg = <0x078b7000 0x600>;
>> +			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&gcc GCC_BLSP1_QUP3_SPI_APPS_CLK>,
>> +				 <&gcc GCC_BLSP1_AHB_CLK>;
>> +			clock-names = "core", "iface";
>> +			dmas = <&blsp1_dma 8>, <&blsp1_dma 9>;
>> +			dma-names = "tx", "rx";
>> +			pinctrl-names = "default", "sleep";
>> +			pinctrl-0 = <&spi3_default>;
>> +			pinctrl-1 = <&spi3_sleep>;
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			status = "disabled";
>> +		};
>> +
>> +		blsp_i2c4: i2c@78b8000 {
>> +			compatible = "qcom,i2c-qup-v2.2.1";
>> +			reg = <0x078b8000 0x500>;
>> +			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>,
>> +				 <&gcc GCC_BLSP1_AHB_CLK>;
>> +			clock-names = "core", "iface";
>> +			dmas = <&blsp1_dma 10>, <&blsp1_dma 11>;
>> +			dma-names = "tx", "rx";
>> +			pinctrl-names = "default", "sleep";
>> +			pinctrl-0 = <&i2c4_default>;
>> +			pinctrl-1 = <&i2c4_sleep>;
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			status = "disabled";
>> +		};
>> +
>> +		blsp_i2c5: i2c@7af5000 {
>> +			compatible = "qcom,i2c-qup-v2.2.1";
>> +			reg = <0x07af5000 0x600>;
>> +			interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>,
>> +				 <&gcc GCC_BLSP2_AHB_CLK>;
>> +			clock-names = "core", "iface";
>> +			dmas = <&blsp2_dma 4>, <&blsp2_dma 5>;
>> +			dma-names = "tx", "rx";
>> +			pinctrl-names = "default", "sleep";
>> +			pinctrl-0 = <&i2c5_default>;
>> +			pinctrl-1 = <&i2c5_sleep>;
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			status = "disabled";
>> +		};
>> +
>> +		blsp_spi6: spi@7af6000 {
>> +			compatible = "qcom,spi-qup-v2.2.1";
>> +			reg = <0x07af6000 0x600>;
>> +			interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&gcc GCC_BLSP2_QUP2_SPI_APPS_CLK>,
>> +				 <&gcc GCC_BLSP2_AHB_CLK>;
>> +			clock-names = "core", "iface";
>> +			dmas = <&blsp2_dma 6>, <&blsp2_dma 7>;
>> +			dma-names = "tx", "rx";
>> +			pinctrl-names = "default", "sleep";
>> +			pinctrl-0 = <&spi6_default>;
>> +			pinctrl-1 = <&spi6_sleep>;
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			status = "disabled";
>> +		};
>> +
>> +		usb_hs_phy: phy@6c000 {
>> +			compatible = "qcom,usb-hs-28nm-femtophy";
>> +			reg = <0x6c000 0x200>;
>> +			#phy-cells = <0>;
>> +			clocks = <&xo_board>,
>> +				 <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>,
>> +				 <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
>> +			clock-names = "ref", "ahb", "sleep";
>> +			resets = <&gcc GCC_QUSB2_PHY_BCR>,
>> +				 <&gcc GCC_USB2_HS_PHY_ONLY_BCR>;
>> +			reset-names = "phy", "por";
>> +			status = "disabled";
>> +		};
>> +
>> +		usb: usb@78db000 {
>> +			compatible = "qcom,ci-hdrc";
>> +			reg = <0x078db000 0x200>,
>> +			      <0x078db200 0x200>;
>> +			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
>> +				     <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&gcc GCC_USB_HS_AHB_CLK>,
>> +				 <&gcc GCC_USB_HS_SYSTEM_CLK>;
>> +			clock-names = "iface", "core";
>> +			assigned-clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>;
>> +			assigned-clock-rates = <80000000>;
>> +			resets = <&gcc GCC_USB_HS_BCR>;
>> +			reset-names = "core";
>> +			phy_type = "ulpi";
>> +			dr_mode = "otg";
>> +			hnp-disable;
>> +			srp-disable;
>> +			adp-disable;
>> +			ahb-burst-config = <0>;
>> +			phy-names = "usb-phy";
>> +			phys = <&usb_hs_phy>;
>> +			status = "disabled";
>> +			#reset-cells = <1>;
>> +		};
>> +
>> +		pronto: wcnss: remoteproc@a21b000 {
> 
> One label should be enough.
> 
>> +			compatible = "qcom,pronto-v3-pil", "qcom,pronto";
>> +			reg = <0x0a204000 0x2000>, <0x0a202000 0x1000>, <0x0a21b000 
>> 0x3000>;
>> +			reg-names = "ccu", "dxe", "pmu";
>> +
>> +			memory-region = <&wcnss_mem>;
>> +
>> +			interrupts-extended = <&intc GIC_SPI 149 IRQ_TYPE_EDGE_RISING>,
>> +					      <&wcnss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
>> +					      <&wcnss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
>> +					      <&wcnss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
>> +					      <&wcnss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
>> +			interrupt-names = "wdog", "fatal", "ready", "handover", 
>> "stop-ack";
>> +
>> +			power-domains = <&rpmpd MSM8917_VDDCX>,
>> +					<&rpmpd MSM8917_VDDMX>;
>> +			power-domain-names = "cx", "mx";
>> +
>> +			qcom,smem-states = <&wcnss_smp2p_out 0>;
>> +			qcom,smem-state-names = "stop";
>> +
>> +			pinctrl-names = "default";
>> +			pinctrl-0 = <&wcnss_pin_a>;
>> +
>> +			status = "disabled";
>> +
>> +			wcnss_iris: iris {
>> +				clocks = <&rpmcc RPM_SMD_RF_CLK2>;
>> +				clock-names = "xo";
>> +			};
>> +
>> +			smd-edge {
>> +				interrupts = <GIC_SPI 142 IRQ_TYPE_EDGE_RISING>;
>> +
>> +				qcom,ipc = <&apcs 8 17>;
> 
> mboxes
> 
>> +				qcom,smd-edge = <6>;
>> +				qcom,remote-pid = <4>;
>> +
>> +				label = "pronto";
>> +
>> +				wcnss_ctrl: wcnss {
>> +					compatible = "qcom,wcnss";
>> +					qcom,smd-channels = "WCNSS_CTRL";
>> +
>> +					qcom,mmio = <&pronto>;
>> +
>> +					wcnss_bt: bluetooth {
>> +						compatible = "qcom,wcnss-bt";
>> +					};
>> +
>> +					wcnss_wifi: wifi {
>> +						compatible = "qcom,wcnss-wlan";
>> +
>> +						interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
>> +							     <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
>> +						interrupt-names = "tx", "rx";
>> +
>> +						qcom,smem-states = <&apps_smsm 10>, <&apps_smsm 9>;
>> +						qcom,smem-state-names = "tx-enable",
>> +									"tx-rings-empty";
>> +					};
>> +				};
>> +			};
>> +		};
>> +
>> +		intc: interrupt-controller@b000000 {
>> +			compatible = "qcom,msm-qgic2";
>> +			interrupt-controller;
>> +			#interrupt-cells = <3>;
>> +			reg = <0x0b000000 0x1000>,
>> +			      <0x0b002000 0x1000>;
>> +		};
>> +
>> +		watchdog@b017000 {
>> +			compatible = "qcom,apss-wdt-qcs404", "qcom,kpss-wdt";
>> +			reg = <0x0b017000 0x1000>;
>> +			clocks = <&sleep_clk>;
>> +		};
>> +
>> +		timer@b120000 {
>> +			#address-cells = <1>;
>> +			#size-cells = <1>;
>> +			ranges;
>> +			compatible = "arm,armv7-timer-mem";
>> +			reg = <0x0b120000 0x1000>;
>> +			clock-frequency = <19200000>;
>> +
>> +			frame@b121000 {
>> +				frame-number = <0>;
>> +				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
>> +					     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
>> +				reg = <0x0b121000 0x1000>,
>> +				      <0x0b122000 0x1000>;
>> +			};
>> +
>> +			frame@b123000 {
>> +				frame-number = <1>;
>> +				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
>> +				reg = <0x0b123000 0x1000>;
>> +				status = "disabled";
>> +			};
>> +
>> +			frame@b124000 {
>> +				frame-number = <2>;
>> +				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
>> +				reg = <0x0b124000 0x1000>;
>> +				status = "disabled";
>> +			};
>> +
>> +			frame@b125000 {
>> +				frame-number = <3>;
>> +				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
>> +				reg = <0x0b125000 0x1000>;
>> +				status = "disabled";
>> +			};
>> +
>> +			frame@b126000 {
>> +				frame-number = <4>;
>> +				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
>> +				reg = <0x0b126000 0x1000>;
>> +				status = "disabled";
>> +			};
>> +
>> +			frame@b127000 {
>> +				frame-number = <5>;
>> +				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
>> +				reg = <0x0b127000 0x1000>;
>> +				status = "disabled";
>> +			};
>> +
>> +			frame@b128000 {
>> +				frame-number = <6>;
>> +				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
>> +				reg = <0x0b128000 0x1000>;
>> +				status = "disabled";
>> +			};
>> +		};
>> +	};
>> +
>> +	thermal_zones: thermal-zones {
>> +		aoss-thermal {
>> +			polling-delay-passive = <250>;
>> +			polling-delay = <1000>;
>> +
>> +			thermal-sensors = <&tsens 0>;
>> +
>> +			trips {
>> +				aoss_alert0: trip-point0 {
>> +					temperature = <85000>;
>> +					hysteresis = <2000>;
>> +					type = "hot";
>> +				};
>> +			};
>> +		};
>> +
>> +		mdm-core-thermal {
>> +			polling-delay-passive = <250>;
>> +			polling-delay = <1000>;
>> +
>> +			thermal-sensors = <&tsens 1>;
>> +
>> +			trips {
>> +				mdm_core_alert0: trip-point0 {
>> +					temperature = <85000>;
>> +					hysteresis = <2000>;
>> +					type = "hot";
>> +				};
>> +			};
>> +		};
>> +
>> +		q6-thermal {
>> +			polling-delay-passive = <250>;
>> +			polling-delay = <1000>;
>> +
>> +			thermal-sensors = <&tsens 2>;
>> +
>> +			trips {
>> +				q6_alert0: trip-point0 {
>> +					temperature = <85000>;
>> +					hysteresis = <2000>;
>> +					type = "hot";
>> +				};
>> +			};
>> +		};
>> +
>> +		camera-thermal {
>> +			polling-delay-passive = <250>;
>> +			polling-delay = <1000>;
>> +
>> +			thermal-sensors = <&tsens 3>;
>> +
>> +			trips {
>> +				camera_alert0: trip-point0 {
>> +					temperature = <85000>;
>> +					hysteresis = <2000>;
>> +					type = "hot";
>> +				};
>> +			};
>> +		};
>> +
>> +		cpuss1-thermal {
>> +			polling-delay-passive = <250>;
>> +			polling-delay = <1000>;
>> +
>> +			thermal-sensors = <&tsens 4>;
>> +
>> +			trips {
>> +				cpuss1_alert0: trip-point0 {
>> +					temperature = <75000>;
>> +					hysteresis = <2000>;
>> +					type = "passive";
>> +				};
>> +
>> +				cpuss1_alert1: trip-point1 {
>> +					temperature = <85000>;
>> +					hysteresis = <2000>;
>> +					type = "hot";
>> +				};
>> +
>> +				cpuss1_crit: cpuss1-crit {
>> +					temperature = <100000>;
>> +					hysteresis = <2000>;
>> +					type = "critical";
>> +				};
>> +			};
>> +			cooling-maps {
>> +				map0 {
>> +					trip = <&cpuss1_alert0>;
>> +					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>> +							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>> +							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>> +							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>> +				};
>> +			};
>> +		};
>> +
>> +		cpu0-thermal {
>> +			polling-delay-passive = <250>;
>> +			polling-delay = <1000>;
>> +
>> +			thermal-sensors = <&tsens 5>;
>> +
>> +			trips {
>> +				cpu0_alert0: trip-point0 {
>> +					temperature = <75000>;
>> +					hysteresis = <2000>;
>> +					type = "passive";
>> +				};
>> +
>> +				cpu0_alert1: trip-point1 {
>> +					temperature = <85000>;
>> +					hysteresis = <2000>;
>> +					type = "hot";
>> +				};
>> +
>> +				cpu0_crit: cpu-crit {
>> +					temperature = <100000>;
>> +					hysteresis = <2000>;
>> +					type = "critical";
>> +				};
>> +			};
>> +			cooling-maps {
>> +				map0 {
>> +					trip = <&cpu0_alert1>;
>> +					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>> +							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>> +							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>> +							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>> +				};
>> +			};
>> +		};
>> +
>> +		cpu1-thermal {
>> +			polling-delay-passive = <250>;
>> +			polling-delay = <1000>;
>> +
>> +			thermal-sensors = <&tsens 6>;
>> +
>> +			trips {
>> +				cpu1_alert0: trip-point0 {
>> +					temperature = <75000>;
>> +					hysteresis = <2000>;
>> +					type = "hot";
>> +				};
>> +
>> +				cpu1_alert1: trip-point1 {
>> +					temperature = <85000>;
>> +					hysteresis = <2000>;
>> +					type = "passive";
>> +				};
>> +
>> +				cpu1_crit: cpu-crit {
>> +					temperature = <100000>;
>> +					hysteresis = <2000>;
>> +					type = "critical";
>> +				};
>> +			};
>> +			cooling-maps {
>> +				map0 {
>> +					trip = <&cpu1_alert1>;
>> +					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>> +							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>> +							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>> +							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>> +				};
>> +			};
>> +		};
>> +
>> +		cpu2-thermal {
>> +			polling-delay-passive = <250>;
>> +			polling-delay = <1000>;
>> +
>> +			thermal-sensors = <&tsens 7>;
>> +
>> +			trips {
>> +				cpu2_alert0: trip-point0 {
>> +					temperature = <75000>;
>> +					hysteresis = <2000>;
>> +					type = "hot";
>> +				};
>> +
>> +				cpu2_alert1: trip-point1 {
>> +					temperature = <85000>;
>> +					hysteresis = <2000>;
>> +					type = "passive";
>> +				};
>> +
>> +				cpu2_crit: cpu-crit {
>> +					temperature = <100000>;
>> +					hysteresis = <2000>;
>> +					type = "critical";
>> +				};
>> +			};
>> +			cooling-maps {
>> +				map0 {
>> +					trip = <&cpu2_alert1>;
>> +					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>> +							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>> +							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>> +							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>> +				};
>> +			};
>> +		};
>> +
>> +		cpu3-thermal {
>> +			polling-delay-passive = <250>;
>> +			polling-delay = <1000>;
>> +
>> +			thermal-sensors = <&tsens 8>;
>> +
>> +			trips {
>> +				cpu3_alert0: trip-point0 {
>> +					temperature = <75000>;
>> +					hysteresis = <2000>;
>> +					type = "hot";
>> +				};
>> +
>> +				cpu3_alert1: trip-point1 {
>> +					temperature = <85000>;
>> +					hysteresis = <2000>;
>> +					type = "passive";
>> +				};
>> +
>> +				cpu3_crit: cpu-crit {
>> +					temperature = <100000>;
>> +					hysteresis = <2000>;
>> +					type = "critical";
>> +				};
>> +			};
>> +			cooling-maps {
>> +				map0 {
>> +					trip = <&cpu3_alert1>;
>> +					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>> +							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>> +							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>> +							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>> +				};
>> +			};
>> +		};
>> +
>> +		gpu-thermal {
>> +			polling-delay-passive = <250>;
>> +			polling-delay = <1000>;
>> +
>> +			thermal-sensors = <&tsens 9>;
>> +
>> +			trips {
>> +				gpu_alert: trip-point0 {
>> +					temperature = <70000>;
>> +					hysteresis = <2000>;
>> +					type = "passive";
>> +				};
>> +
>> +				gpu_crit: gpu-crit {
>> +					temperature = <90000>;
>> +					hysteresis = <2000>;
>> +					type = "critical";
>> +				};
>> +			};
>> +
>> +			cooling-maps {
>> +				map0 {
>> +					trip = <&gpu_alert>;
>> +					cooling-device = <&gpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>> +				};
>> +			};
>> +		};
>> +	};
>> +};
>> +
>> +#include "msm8917-pins.dtsi"
>> diff --git a/arch/arm64/boot/dts/qcom/pm8916.dtsi 
>> b/arch/arm64/boot/dts/qcom/pm8916.dtsi
>> index 
>> f8e4829ff7f7de1f1f4f5da0f41020875d6c7e17..df0f679250ccb6c49a76288fad12f67b01fa6b61 
>> 100644
>> --- a/arch/arm64/boot/dts/qcom/pm8916.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/pm8916.dtsi
> 
> Separate commit, please. Or move this to the board file submission.
> 
>> @@ -47,7 +47,7 @@ pon@800 {
>>  			mode-bootloader = <0x2>;
>>  			mode-recovery = <0x1>;
>> 
>> -			pwrkey {
>> +			pm8916_pwrkey: pwrkey {
>>  				compatible = "qcom,pm8941-pwrkey";
>>  				interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
>>  				debounce = <15625>;
>> @@ -210,6 +210,10 @@ pm8916_pwm: pwm {
>>  			status = "disabled";
>>  		};
>> 
>> +		pm8916_spmi_regulators: regulators {
>> +			compatible = "qcom,pm8916-regulators";
>> +		};
>> +
>>  		pm8916_vib: vibrator@c000 {
>>  			compatible = "qcom,pm8916-vib";
>>  			reg = <0xc000>;
>> @@ -219,6 +223,9 @@ pm8916_vib: vibrator@c000 {
>>  		pm8916_codec: audio-codec@f000 {
>>  			compatible = "qcom,pm8916-wcd-analog-codec";
>>  			reg = <0xf000>;
>> +			reg-names = "pmic-codec-core";
>> +			clocks = <&xo_board>;
>> +			clock-names = "mclk";
> 
> Why? Is this compatible with other boards?
> 
>>  			interrupt-parent = <&spmi_bus>;
>>  			interrupts = <0x1 0xf0 0x0 IRQ_TYPE_NONE>,
>>  				     <0x1 0xf0 0x1 IRQ_TYPE_NONE>,
>> 
>> --
>> 2.47.0
>> 

Re: [PATCH RFC 10/14] dt-bindings: iommu: qcom,iommu: Add MSM8917 IOMMU to SMMUv1 compatibles

[Will Deacon]

On Sat, Oct 19, 2024 at 08:21:16AM -0500, Rob Herring (Arm) wrote:
> 
> On Sat, 19 Oct 2024 13:50:47 +0200, Barnabás Czémán wrote:
> > Add MSM8917 compatible string with "qcom,msm-iommu-v1" as fallback
> > for the MSM8917 IOMMU which is compatible with Qualcomm's secure
> > fw "SMMU v1" implementation.
> > 
> > Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
> > ---
> >  Documentation/devicetree/bindings/iommu/qcom,iommu.yaml | 1 +
> >  1 file changed, 1 insertion(+)
> > 
> 
> My bot found errors running 'make dt_binding_check' on your patch:
> 
> yamllint warnings/errors:
> 
> dtschema/dtc warnings/errors:
> 
> 
> doc reference errors (make refcheckdocs):
> 
> See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20241019-msm8917-v1-10-f1f3ca1d88e5@mainlining.org

I don't see any errors in the logs...

Will

Re: [PATCH RFC 12/14] arm64: dts: qcom: Add initial support for MSM8917

[Dmitry Baryshkov]

On Mon, Oct 21, 2024 at 11:14:55PM +0200, barnabas.czeman@mainlining.org wrote:
> On 2024-10-19 15:43, Dmitry Baryshkov wrote:
> > On Sat, Oct 19, 2024 at 01:50:49PM +0200, Barnabás Czémán wrote:
> > > From: Otto Pflüger <otto.pflueger@abscue.de>
> > > 
> > > Add initial support for MSM8917 SoC.
> > > 
> > > Signed-off-by: Otto Pflüger <otto.pflueger@abscue.de>
> > > [reword commit, rebase, fix schema errors]
> > > Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
> > > ---
> > >  arch/arm64/boot/dts/qcom/msm8917-pins.dtsi |  344 ++++++
> > >  arch/arm64/boot/dts/qcom/msm8917.dtsi      | 1557
> > > ++++++++++++++++++++++++++++
> > >  arch/arm64/boot/dts/qcom/pm8916.dtsi       |    9 +-
> > >  3 files changed, 1909 insertions(+), 1 deletion(-)
> > > 
> > > diff --git a/arch/arm64/boot/dts/qcom/msm8917-pins.dtsi
> > > b/arch/arm64/boot/dts/qcom/msm8917-pins.dtsi
> > > new file mode 100644
> > > index 0000000000000000000000000000000000000000..f283ffd59b8aca8e510ef95d5526af9592a1c036
> > > --- /dev/null
> > > +++ b/arch/arm64/boot/dts/qcom/msm8917-pins.dtsi
> > 
> > Please merge into msm8917.dtsi (for generic parts) and
> > msm8917-boatd.dtsi (for board-specific parts).
> > 
> > > @@ -0,0 +1,344 @@
> > > +// SPDX-License-Identifier: GPL-2.0
> > 
> > If possible, GPL-2.0 OR MIT, or GPL-2.0 OR BSD-2/3-Clause
> Unfortunatelly i cannot change the license i do not own the original code.

Ack

> > 
> > > +			tsens_caldata: caldata@d0 {
> > > +				reg = <0x01d8 0x14>;
> > > +			};
> > 
> > No, individual bit definitions for each of tsens fuse values.
> > 
> > > +		};
> > > +
> > > +		rpm_msg_ram: sram@60000 {
> > > +			compatible = "qcom,rpm-msg-ram";
> > > +			reg = <0x00060000 0x8000>;
> > > +		};
> > > +
> > > +		tsens: thermal-sensor@4a9000 {
> > > +			compatible = "qcom,msm8917-tsens", "qcom,tsens-v1";
> > > +			reg = <0x004a9000 0x1000>,
> > > +			      <0x004a8000 0x1000>;
> > > +			nvmem-cells = <&tsens_caldata>;
> > > +			nvmem-cell-names = "calib";
> > 
> > And here too, individual bits instead of a single blob.
> I do not know how to do that i have only find some parts at downstream
> driver to be able to separate
> the cells but i do not have every information for it.

Well, you don't have to describe every information. I'm simply asking
you to replace single tsens_caldata entry with per-sensor and per-point
data, see e.g. msm8976.dtsi and data_8976 / ops_8976.

> > 
> > > +			#qcom,sensors = <10>;
> > > +			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
> > > +			interrupt-names = "uplow";
> > > +			#thermal-sensor-cells = <1>;
> > > +		};
> > > +
> > > +

[...]

> > > +		gpu: gpu@1c00000 {
> > > +			compatible = "qcom,adreno-306.32", "qcom,adreno";
> > 
> > Is it really .32 ?
> Yes it is A306A (Adreno 308)

Ack

-- 
With best wishes
Dmitry