* [PATCH v8 1/4] mfd: add support for Diolan DLN-2 devices
2014-10-15 14:48 [PATCH v8 0/4] mfd: add support for Diolan DLN-2 Octavian Purdila
@ 2014-10-15 14:48 ` Octavian Purdila
2014-10-23 15:16 ` Johan Hovold
2014-10-15 14:48 ` [PATCH v8 2/4] i2c: add support for Diolan DLN-2 USB-I2C adapter Octavian Purdila
` (2 subsequent siblings)
3 siblings, 1 reply; 14+ messages in thread
From: Octavian Purdila @ 2014-10-15 14:48 UTC (permalink / raw)
To: gregkh, linus.walleij, gnurou, wsa, sameo, lee.jones
Cc: arnd, johan, daniel.baluta, laurentiu.palcu, linux-usb,
linux-kernel, linux-gpio, linux-i2c, Octavian Purdila
This patch implements the USB part of the Diolan USB-I2C/SPI/GPIO
Master Adapter DLN-2. Details about the device can be found here:
https://www.diolan.com/i2c/i2c_interface.html.
Information about the USB protocol can be found in the Programmer's
Reference Manual [1], see section 1.7.
Because the hardware has a single transmit endpoint and a single
receive endpoint the communication between the various DLN2 drivers
and the hardware will be muxed/demuxed by this driver.
Each DLN2 module will be identified by the handle field within the DLN2
message header. If a DLN2 module issues multiple commands in parallel
they will be identified by the echo counter field in the message header.
The DLN2 modules can use the dln2_transfer() function to issue a
command and wait for its response. They can also register a callback
that is going to be called when a specific event id is generated by
the device (e.g. GPIO interrupts). The device uses handle 0 for
sending events.
[1] https://www.diolan.com/downloads/dln-api-manual.pdf
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
---
drivers/mfd/Kconfig | 11 +
drivers/mfd/Makefile | 1 +
drivers/mfd/dln2.c | 756 +++++++++++++++++++++++++++++++++++++++++++++++
include/linux/mfd/dln2.h | 69 +++++
4 files changed, 837 insertions(+)
create mode 100644 drivers/mfd/dln2.c
create mode 100644 include/linux/mfd/dln2.h
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index c9200d3..4538815a 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -189,6 +189,17 @@ config MFD_DA9063
Additional drivers must be enabled in order to use the functionality
of the device.
+config MFD_DLN2
+ tristate "Diolan DLN2 support"
+ select MFD_CORE
+ depends on USB
+ help
+
+ This adds support for Diolan USB-I2C/SPI/GPIO Master Adapter
+ DLN-2. Additional drivers such as I2C_DLN2, GPIO_DLN2,
+ etc. must be enabled in order to use the functionality of
+ the device.
+
config MFD_MC13XXX
tristate
depends on (SPI_MASTER || I2C)
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 61f8dbf..2cd7e74 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -175,6 +175,7 @@ obj-$(CONFIG_MFD_STW481X) += stw481x.o
obj-$(CONFIG_MFD_IPAQ_MICRO) += ipaq-micro.o
obj-$(CONFIG_MFD_MENF21BMC) += menf21bmc.o
obj-$(CONFIG_MFD_HI6421_PMIC) += hi6421-pmic-core.o
+obj-$(CONFIG_MFD_DLN2) += dln2.o
intel-soc-pmic-objs := intel_soc_pmic_core.o intel_soc_pmic_crc.o
obj-$(CONFIG_INTEL_SOC_PMIC) += intel-soc-pmic.o
diff --git a/drivers/mfd/dln2.c b/drivers/mfd/dln2.c
new file mode 100644
index 0000000..124b262
--- /dev/null
+++ b/drivers/mfd/dln2.c
@@ -0,0 +1,756 @@
+/*
+ * Driver for the Diolan DLN-2 USB adapter
+ *
+ * Copyright (c) 2014 Intel Corporation
+ *
+ * Derived from:
+ * i2c-diolan-u2c.c
+ * Copyright (c) 2010-2011 Ericsson AB
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation, version 2.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/slab.h>
+#include <linux/usb.h>
+#include <linux/i2c.h>
+#include <linux/mutex.h>
+#include <linux/platform_device.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/dln2.h>
+#include <linux/rculist.h>
+
+struct dln2_header {
+ __le16 size;
+ __le16 id;
+ __le16 echo;
+ __le16 handle;
+} __packed;
+
+struct dln2_response {
+ struct dln2_header hdr;
+ __le16 result;
+} __packed;
+
+#define DLN2_GENERIC_MODULE_ID 0x00
+#define DLN2_GENERIC_CMD(cmd) DLN2_CMD(cmd, DLN2_GENERIC_MODULE_ID)
+#define CMD_GET_DEVICE_VER DLN2_GENERIC_CMD(0x30)
+#define CMD_GET_DEVICE_SN DLN2_GENERIC_CMD(0x31)
+
+#define DLN2_HW_ID 0x200
+#define DLN2_USB_TIMEOUT 200 /* in ms */
+#define DLN2_MAX_RX_SLOTS 16
+#define DLN2_MAX_URBS 16
+#define DLN2_RX_BUF_SIZE 512
+
+enum dln2_handle {
+ DLN2_HANDLE_EVENT = 0, /* don't change, hardware defined */
+ DLN2_HANDLE_CTRL,
+ DLN2_HANDLE_GPIO,
+ DLN2_HANDLE_I2C,
+ DLN2_HANDLES
+};
+
+/*
+ * Receive context used between the receive demultiplexer and the
+ * transfer routine. While sending a request the transfer routine
+ * will look for a free receive context and use it to wait for a
+ * response and to receive the URB and thus the response data.
+ */
+struct dln2_rx_context {
+ /* completion used to wait for a response */
+ struct completion done;
+
+ /* if non-NULL the URB contains the response */
+ struct urb *urb;
+
+ /* if true then this context is used to wait for a response */
+ bool in_use;
+};
+
+/*
+ * Receive contexts for a particular DLN2 module (i2c, gpio, etc.). We
+ * use the handle header field to identify the module in
+ * dln2_dev.mod_rx_slots and then the echo header field to index the
+ * slots field and find the receive context for a particular request.
+ */
+struct dln2_mod_rx_slots {
+ /* RX slots bitmap */
+ DECLARE_BITMAP(bmap, DLN2_MAX_RX_SLOTS);
+
+ /* used to wait for a free RX slot */
+ wait_queue_head_t wq;
+
+ /* used to wait for an RX operation to complete */
+ struct dln2_rx_context slots[DLN2_MAX_RX_SLOTS];
+
+ /* avoid races between alloc/free_rx_slot and dln2_rx_transfer */
+ spinlock_t lock;
+};
+
+struct dln2_dev {
+ struct usb_device *usb_dev;
+ struct usb_interface *interface;
+ u8 ep_in;
+ u8 ep_out;
+
+ struct urb *rx_urb[DLN2_MAX_URBS];
+ void *rx_buf[DLN2_MAX_URBS];
+
+ struct dln2_mod_rx_slots mod_rx_slots[DLN2_HANDLES];
+
+ struct list_head event_cb_list;
+ spinlock_t event_cb_lock;
+
+ bool disconnect;
+ int active_transfers;
+ wait_queue_head_t disconnect_wq;
+ spinlock_t disconnect_lock;
+};
+
+struct dln2_event_cb_entry {
+ struct list_head list;
+ u16 id;
+ struct platform_device *pdev;
+ dln2_event_cb_t callback;
+};
+
+int dln2_register_event_cb(struct platform_device *pdev, u16 id,
+ dln2_event_cb_t rx_cb)
+{
+ struct dln2_dev *dln2 = dev_get_drvdata(pdev->dev.parent);
+ struct dln2_event_cb_entry *i, *new_cb;
+ unsigned long flags;
+ int ret = 0;
+
+ new_cb = kmalloc(sizeof(*new_cb), GFP_KERNEL);
+ if (!new_cb)
+ return -ENOMEM;
+
+ new_cb->id = id;
+ new_cb->callback = rx_cb;
+ new_cb->pdev = pdev;
+
+ spin_lock_irqsave(&dln2->event_cb_lock, flags);
+
+ list_for_each_entry(i, &dln2->event_cb_list, list) {
+ if (i->id == id) {
+ ret = -EBUSY;
+ break;
+ }
+ }
+
+ if (!ret)
+ list_add_rcu(&new_cb->list, &dln2->event_cb_list);
+
+ spin_unlock_irqrestore(&dln2->event_cb_lock, flags);
+
+ if (ret)
+ kfree(new_cb);
+
+ return ret;
+}
+EXPORT_SYMBOL(dln2_register_event_cb);
+
+void dln2_unregister_event_cb(struct platform_device *pdev, u16 id)
+{
+ struct dln2_dev *dln2 = dev_get_drvdata(pdev->dev.parent);
+ struct dln2_event_cb_entry *i;
+ unsigned long flags;
+ bool found = false;
+
+ spin_lock_irqsave(&dln2->event_cb_lock, flags);
+
+ list_for_each_entry(i, &dln2->event_cb_list, list) {
+ if (i->id == id) {
+ list_del_rcu(&i->list);
+ found = true;
+ break;
+ }
+ }
+
+ spin_unlock_irqrestore(&dln2->event_cb_lock, flags);
+
+ if (found) {
+ synchronize_rcu();
+ kfree(i);
+ }
+}
+EXPORT_SYMBOL(dln2_unregister_event_cb);
+
+static bool dln2_rx_transfer(struct dln2_dev *dln2, struct urb *urb,
+ u16 handle, u16 rx_slot)
+{
+ struct dln2_mod_rx_slots *rxs = &dln2->mod_rx_slots[handle];
+ struct dln2_rx_context *rxc;
+ bool ret = false;
+
+ rxc = &rxs->slots[rx_slot];
+
+ /*
+ * No need to disable interrupts as this lock is not taken in
+ * interrupt context elsewhere in this driver and this
+ * function (or its callers) are not exported to other
+ * modules.
+ */
+ spin_lock(&rxs->lock);
+ if (rxc->in_use && !rxc->urb) {
+ rxc->urb = urb;
+ complete(&rxc->done);
+ ret = true;
+ }
+ spin_unlock(&rxs->lock);
+
+ return ret;
+}
+
+static void dln2_run_event_callbacks(struct dln2_dev *dln2, u16 id, u16 echo,
+ void *data, int len)
+{
+ struct dln2_event_cb_entry *i;
+
+ rcu_read_lock();
+
+ list_for_each_entry_rcu(i, &dln2->event_cb_list, list)
+ if (i->id == id)
+ i->callback(i->pdev, echo, data, len);
+
+ rcu_read_unlock();
+}
+
+static void dln2_rx(struct urb *urb)
+{
+ struct dln2_dev *dln2 = urb->context;
+ struct dln2_header *hdr = urb->transfer_buffer;
+ struct device *dev = &dln2->interface->dev;
+ u16 id, echo, handle, size;
+ u8 *data;
+ int len;
+ int err;
+
+ switch (urb->status) {
+ case 0:
+ /* success */
+ break;
+ case -ECONNRESET:
+ case -ENOENT:
+ case -ESHUTDOWN:
+ case -EPIPE:
+ /* this urb is terminated, clean up */
+ dev_dbg(dev, "urb shutting down with status %d\n", urb->status);
+ return;
+ default:
+ dev_dbg(dev, "nonzero urb status received %d\n", urb->status);
+ goto out;
+ }
+
+ if (urb->actual_length < sizeof(struct dln2_header)) {
+ dev_err(dev, "short response: %d\n", urb->actual_length);
+ goto out;
+ }
+
+ handle = le16_to_cpu(hdr->handle);
+ id = le16_to_cpu(hdr->id);
+ echo = le16_to_cpu(hdr->echo);
+ size = le16_to_cpu(hdr->size);
+
+ if (size != urb->actual_length) {
+ dev_err(dev, "size mismatch: handle %x cmd %x echo %x size %d actual %d\n",
+ handle, id, echo, size, urb->actual_length);
+ goto out;
+ }
+
+ if (handle >= DLN2_HANDLES) {
+ dev_warn(dev, "RX: invalid handle %d\n", handle);
+ goto out;
+ }
+
+ data = urb->transfer_buffer + sizeof(struct dln2_header);
+ len = urb->actual_length - sizeof(struct dln2_header);
+
+ if (handle == DLN2_HANDLE_EVENT) {
+ dln2_run_event_callbacks(dln2, id, echo, data, len);
+ } else {
+ /* URB will be re-submitted in free_rx_slot */
+ if (dln2_rx_transfer(dln2, urb, handle, echo))
+ return;
+ dev_warn(dev, "bad/late response %d/%d\n", handle, echo);
+ }
+
+out:
+ err = usb_submit_urb(urb, GFP_ATOMIC);
+ if (err < 0)
+ dev_err(dev, "failed to resubmit RX URB: %d\n", err);
+}
+
+static void *dln2_prep_buf(u16 handle, u16 cmd, u16 echo, const void *obuf,
+ int *obuf_len, gfp_t gfp)
+{
+ int len;
+ void *buf;
+ struct dln2_header *hdr;
+
+ len = *obuf_len + sizeof(*hdr);
+ buf = kmalloc(len, gfp);
+ if (!buf)
+ return NULL;
+
+ hdr = (struct dln2_header *)buf;
+ hdr->id = cpu_to_le16(cmd);
+ hdr->size = cpu_to_le16(len);
+ hdr->echo = cpu_to_le16(echo);
+ hdr->handle = cpu_to_le16(handle);
+
+ memcpy(buf + sizeof(*hdr), obuf, *obuf_len);
+
+ *obuf_len = len;
+
+ return buf;
+}
+
+static int dln2_send_wait(struct dln2_dev *dln2, u16 handle, u16 cmd, u16 echo,
+ const void *obuf, int obuf_len)
+{
+ int ret = 0;
+ int len = obuf_len;
+ void *buf;
+ int actual;
+
+ buf = dln2_prep_buf(handle, cmd, echo, obuf, &len, GFP_KERNEL);
+ if (!buf)
+ return -ENOMEM;
+
+ ret = usb_bulk_msg(dln2->usb_dev,
+ usb_sndbulkpipe(dln2->usb_dev, dln2->ep_out),
+ buf, len, &actual, DLN2_USB_TIMEOUT);
+
+ kfree(buf);
+
+ return ret;
+}
+
+static bool find_free_slot(struct dln2_dev *dln2, u16 handle, int *slot)
+{
+ struct dln2_mod_rx_slots *rxs;
+ unsigned long flags;
+
+ if (dln2->disconnect) {
+ *slot = -ENODEV;
+ return true;
+ }
+
+ rxs = &dln2->mod_rx_slots[handle];
+
+ spin_lock_irqsave(&rxs->lock, flags);
+
+ *slot = find_first_zero_bit(rxs->bmap, DLN2_MAX_RX_SLOTS);
+
+ if (*slot < DLN2_MAX_RX_SLOTS) {
+ struct dln2_rx_context *rxc = &rxs->slots[*slot];
+
+ set_bit(*slot, rxs->bmap);
+ rxc->in_use = true;
+ }
+
+ spin_unlock_irqrestore(&rxs->lock, flags);
+
+ return *slot < DLN2_MAX_RX_SLOTS;
+}
+
+static int alloc_rx_slot(struct dln2_dev *dln2, u16 handle)
+{
+ int ret;
+ int slot;
+
+ /*
+ * No need to timeout here, the wait is bounded by the timeout
+ * in _dln2_transfer.
+ */
+ ret = wait_event_interruptible(dln2->mod_rx_slots[handle].wq,
+ find_free_slot(dln2, handle, &slot));
+ if (ret < 0)
+ return ret;
+
+ return slot;
+}
+
+static void free_rx_slot(struct dln2_dev *dln2, u16 handle, int slot)
+{
+ struct dln2_mod_rx_slots *rxs;
+ struct urb *urb = NULL;
+ unsigned long flags;
+ struct dln2_rx_context *rxc;
+
+ rxs = &dln2->mod_rx_slots[handle];
+
+ spin_lock_irqsave(&rxs->lock, flags);
+
+ clear_bit(slot, rxs->bmap);
+
+ rxc = &rxs->slots[slot];
+ rxc->in_use = false;
+ urb = rxc->urb;
+ rxc->urb = NULL;
+ reinit_completion(&rxc->done);
+
+ spin_unlock_irqrestore(&rxs->lock, flags);
+
+ if (urb) {
+ int err;
+ struct device *dev = &dln2->interface->dev;
+
+ err = usb_submit_urb(urb, GFP_KERNEL);
+ if (err < 0)
+ dev_err(dev, "failed to resubmit RX URB: %d\n", err);
+ }
+
+ wake_up_interruptible(&rxs->wq);
+}
+
+static int _dln2_transfer(struct dln2_dev *dln2, u16 handle, u16 cmd,
+ const void *obuf, unsigned obuf_len,
+ void *ibuf, unsigned *ibuf_len, u16 *result)
+{
+ int ret = 0;
+ int rx_slot;
+ struct dln2_response *rsp;
+ struct dln2_rx_context *rxc;
+ struct device *dev = &dln2->interface->dev;
+ const int timeout = DLN2_USB_TIMEOUT * HZ / 1000;
+ struct dln2_mod_rx_slots *rxs = &dln2->mod_rx_slots[handle];
+
+ spin_lock(&dln2->disconnect_lock);
+ if (!dln2->disconnect)
+ dln2->active_transfers++;
+ else
+ ret = -ENODEV;
+ spin_unlock(&dln2->disconnect_lock);
+
+ if (ret)
+ return ret;
+
+ rx_slot = alloc_rx_slot(dln2, handle);
+ if (rx_slot < 0) {
+ ret = rx_slot;
+ goto out_decr;
+ }
+
+ ret = dln2_send_wait(dln2, handle, cmd, rx_slot, obuf, obuf_len);
+ if (ret < 0) {
+ dev_err(dev, "USB write failed: %d\n", ret);
+ goto out_free_rx_slot;
+ }
+
+ rxc = &rxs->slots[rx_slot];
+
+ ret = wait_for_completion_interruptible_timeout(&rxc->done, timeout);
+ if (ret <= 0) {
+ if (!ret)
+ ret = -ETIMEDOUT;
+ goto out_free_rx_slot;
+ }
+
+ if (dln2->disconnect) {
+ ret = -ENODEV;
+ goto out_free_rx_slot;
+ }
+
+ /* if we got here we know that the response header has been checked */
+ rsp = rxc->urb->transfer_buffer;
+
+ if (rsp->hdr.size < sizeof(*rsp)) {
+ ret = -EPROTO;
+ goto out_free_rx_slot;
+ }
+
+ if (result)
+ *result = le16_to_cpu(rsp->result);
+ if (le16_to_cpu(rsp->result) > 0x80) {
+ dev_dbg(dev, "%d received response with error %d\n",
+ handle, le16_to_cpu(rsp->result));
+ ret = -EREMOTEIO;
+ goto out_free_rx_slot;
+ }
+
+ if (!ibuf) {
+ ret = 0;
+ goto out_free_rx_slot;
+ }
+
+ if (*ibuf_len > rsp->hdr.size - sizeof(*rsp))
+ *ibuf_len = rsp->hdr.size - sizeof(*rsp);
+
+ memcpy(ibuf, rsp + 1, *ibuf_len);
+
+out_free_rx_slot:
+ free_rx_slot(dln2, handle, rx_slot);
+out_decr:
+ spin_lock(&dln2->disconnect_lock);
+ dln2->active_transfers--;
+ spin_unlock(&dln2->disconnect_lock);
+ if (dln2->disconnect)
+ wake_up(&dln2->disconnect_wq);
+
+ return ret;
+}
+
+int dln2_transfer(struct platform_device *pdev, u16 cmd,
+ const void *obuf, unsigned obuf_len,
+ void *ibuf, unsigned *ibuf_len, u16 *result)
+{
+ struct dln2_platform_data *dln2_pdata;
+ struct dln2_dev *dln2;
+ u16 handle;
+
+ dln2 = dev_get_drvdata(pdev->dev.parent);
+ dln2_pdata = dev_get_platdata(&pdev->dev);
+ handle = dln2_pdata->handle;
+
+ return _dln2_transfer(dln2, handle, cmd, obuf, obuf_len, ibuf, ibuf_len,
+ result);
+}
+EXPORT_SYMBOL(dln2_transfer);
+
+static int dln2_check_hw(struct dln2_dev *dln2)
+{
+ int ret;
+ __le32 hw_type;
+ int len = sizeof(hw_type);
+
+ ret = _dln2_transfer(dln2, DLN2_HANDLE_CTRL, CMD_GET_DEVICE_VER,
+ NULL, 0, &hw_type, &len, NULL);
+ if (ret < 0)
+ return ret;
+ if (len < sizeof(hw_type))
+ return -EREMOTEIO;
+
+ if (le32_to_cpu(hw_type) != DLN2_HW_ID) {
+ dev_err(&dln2->interface->dev, "Device ID 0x%x not supported\n",
+ le32_to_cpu(hw_type));
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static int dln2_print_serialno(struct dln2_dev *dln2)
+{
+ int ret;
+ __le32 serial_no;
+ int len = sizeof(serial_no);
+ struct device *dev = &dln2->interface->dev;
+
+ ret = _dln2_transfer(dln2, DLN2_HANDLE_CTRL, CMD_GET_DEVICE_SN, NULL, 0,
+ &serial_no, &len, NULL);
+ if (ret < 0)
+ return ret;
+ if (len < sizeof(serial_no))
+ return -EREMOTEIO;
+
+ dev_info(dev, "Diolan DLN2 serial 0x%x\n", le32_to_cpu(serial_no));
+
+ return 0;
+}
+
+static int dln2_hw_init(struct dln2_dev *dln2)
+{
+ int ret;
+
+ ret = dln2_check_hw(dln2);
+ if (ret < 0)
+ return ret;
+
+ return dln2_print_serialno(dln2);
+}
+
+static void dln2_free_rx_urbs(struct dln2_dev *dln2)
+{
+ int i;
+
+ for (i = 0; i < DLN2_MAX_URBS; i++) {
+ usb_kill_urb(dln2->rx_urb[i]);
+ usb_free_urb(dln2->rx_urb[i]);
+ kfree(dln2->rx_buf[i]);
+ }
+}
+
+static void dln2_free(struct dln2_dev *dln2)
+{
+ dln2_free_rx_urbs(dln2);
+ usb_put_dev(dln2->usb_dev);
+ kfree(dln2);
+}
+
+static int dln2_setup_rx_urbs(struct dln2_dev *dln2,
+ struct usb_host_interface *hostif)
+{
+ int i;
+ const int rx_max_size = DLN2_RX_BUF_SIZE;
+
+ for (i = 0; i < DLN2_MAX_URBS; i++) {
+ int ret;
+ struct device *dev = &dln2->interface->dev;
+
+ dln2->rx_buf[i] = kmalloc(rx_max_size, GFP_KERNEL);
+ if (!dln2->rx_buf[i])
+ return -ENOMEM;
+
+ dln2->rx_urb[i] = usb_alloc_urb(0, GFP_KERNEL);
+ if (!dln2->rx_urb[i])
+ return -ENOMEM;
+
+ usb_fill_bulk_urb(dln2->rx_urb[i], dln2->usb_dev,
+ usb_rcvbulkpipe(dln2->usb_dev, dln2->ep_in),
+ dln2->rx_buf[i], rx_max_size, dln2_rx, dln2);
+
+ ret = usb_submit_urb(dln2->rx_urb[i], GFP_KERNEL);
+ if (ret < 0) {
+ dev_err(dev, "failed to submit RX URB: %d\n", ret);
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+static struct dln2_platform_data dln2_pdata_gpio = {
+ .handle = DLN2_HANDLE_GPIO,
+};
+
+/* Only one I2C port seems to be supported on current hardware */
+static struct dln2_platform_data dln2_pdata_i2c = {
+ .handle = DLN2_HANDLE_I2C,
+ .port = 0,
+};
+
+static const struct mfd_cell dln2_devs[] = {
+ {
+ .name = "dln2-gpio",
+ .platform_data = &dln2_pdata_gpio,
+ .pdata_size = sizeof(struct dln2_platform_data),
+ },
+ {
+ .name = "dln2-i2c",
+ .platform_data = &dln2_pdata_i2c,
+ .pdata_size = sizeof(struct dln2_platform_data),
+ },
+};
+
+static void dln2_disconnect(struct usb_interface *interface)
+{
+ struct dln2_dev *dln2 = usb_get_intfdata(interface);
+ int i, j;
+
+ /* don't allow starting new transfers */
+ spin_lock(&dln2->disconnect_lock);
+ dln2->disconnect = true;
+ spin_unlock(&dln2->disconnect_lock);
+
+ /* cancel in progress transfers */
+ for (i = 0; i < DLN2_HANDLES; i++) {
+ struct dln2_mod_rx_slots *rxs = &dln2->mod_rx_slots[i];
+ unsigned long flags;
+
+ spin_lock_irqsave(&rxs->lock, flags);
+
+ /* cancel all response waiters */
+ for (j = 0; j < DLN2_MAX_RX_SLOTS; j++) {
+ struct dln2_rx_context *rxc = &rxs->slots[j];
+
+ if (rxc->in_use)
+ complete(&rxc->done);
+ }
+
+ spin_unlock_irqrestore(&rxs->lock, flags);
+ }
+
+ /* wait for transfers to end */
+ wait_event(dln2->disconnect_wq, !dln2->active_transfers);
+
+ mfd_remove_devices(&interface->dev);
+
+ dln2_free(dln2);
+}
+
+static int dln2_probe(struct usb_interface *interface,
+ const struct usb_device_id *usb_id)
+{
+ struct usb_host_interface *hostif = interface->cur_altsetting;
+ struct device *dev = &interface->dev;
+ struct dln2_dev *dln2;
+ int ret;
+ int i, j;
+
+ if (hostif->desc.bInterfaceNumber != 0 ||
+ hostif->desc.bNumEndpoints < 2)
+ return -ENODEV;
+
+ dln2 = kzalloc(sizeof(*dln2), GFP_KERNEL);
+ if (!dln2)
+ return -ENOMEM;
+
+ dln2->ep_out = hostif->endpoint[0].desc.bEndpointAddress;
+ dln2->ep_in = hostif->endpoint[1].desc.bEndpointAddress;
+ dln2->usb_dev = usb_get_dev(interface_to_usbdev(interface));
+ dln2->interface = interface;
+ usb_set_intfdata(interface, dln2);
+ init_waitqueue_head(&dln2->disconnect_wq);
+
+ for (i = 0; i < DLN2_HANDLES; i++) {
+ init_waitqueue_head(&dln2->mod_rx_slots[i].wq);
+ spin_lock_init(&dln2->mod_rx_slots[i].lock);
+ for (j = 0; j < DLN2_MAX_RX_SLOTS; j++)
+ init_completion(&dln2->mod_rx_slots[i].slots[j].done);
+ }
+
+ spin_lock_init(&dln2->event_cb_lock);
+ spin_lock_init(&dln2->disconnect_lock);
+ INIT_LIST_HEAD(&dln2->event_cb_list);
+
+ ret = dln2_setup_rx_urbs(dln2, hostif);
+ if (ret)
+ goto out_cleanup;
+
+ ret = dln2_hw_init(dln2);
+ if (ret < 0) {
+ dev_err(dev, "failed to initialize hardware\n");
+ goto out_cleanup;
+ }
+
+ ret = mfd_add_hotplug_devices(dev, dln2_devs, ARRAY_SIZE(dln2_devs));
+ if (ret != 0) {
+ dev_err(dev, "failed to add mfd devices to core\n");
+ goto out_cleanup;
+ }
+
+ return 0;
+
+out_cleanup:
+ dln2_free(dln2);
+
+ return ret;
+}
+
+static const struct usb_device_id dln2_table[] = {
+ { USB_DEVICE(0xa257, 0x2013) },
+ { }
+};
+
+MODULE_DEVICE_TABLE(usb, dln2_table);
+
+static struct usb_driver dln2_driver = {
+ .name = "dln2",
+ .probe = dln2_probe,
+ .disconnect = dln2_disconnect,
+ .id_table = dln2_table,
+};
+
+module_usb_driver(dln2_driver);
+
+MODULE_AUTHOR("Octavian Purdila <octavian.purdila@intel.com>");
+MODULE_DESCRIPTION("Core driver for the Diolan DLN2 interface adapter");
+MODULE_LICENSE("GPL v2");
diff --git a/include/linux/mfd/dln2.h b/include/linux/mfd/dln2.h
new file mode 100644
index 0000000..57ddc58
--- /dev/null
+++ b/include/linux/mfd/dln2.h
@@ -0,0 +1,69 @@
+#ifndef __LINUX_USB_DLN2_H
+#define __LINUX_USB_DLN2_H
+
+#define DLN2_CMD(cmd, id) ((cmd) | ((id) << 8))
+
+struct dln2_platform_data {
+ u16 handle; /* sub-driver handle (internally used only) */
+ u8 port; /* I2C/SPI port */
+};
+
+/**
+ * dln2_event_cb_t - event callback function signature
+ *
+ * @pdev - the sub-device that registered this callback
+ * @echo - the echo header field received in the message
+ * @data - the data payload
+ * @len - the data payload length
+ *
+ * The callback function is called in interrupt context and the data
+ * payload is only valid during the call. If the user needs later
+ * access of the data, it must copy it.
+ */
+
+typedef void (*dln2_event_cb_t)(struct platform_device *pdev, u16 echo,
+ const void *data, int len);
+
+/**
+ * dl2n_register_event_cb - register a callback function for an event
+ *
+ * @pdev - the sub-device that registers the callback
+ * @event - the event for which to register a callback
+ * @event_cb - the callback function
+ *
+ * @return 0 in case of success, negative value in case of error
+ */
+int dln2_register_event_cb(struct platform_device *pdev, u16 event,
+ dln2_event_cb_t event_cb);
+
+/**
+ * dln2_unregister_event_cb - unregister the callback function for an event
+ *
+ * @pdev - the sub-device that registered the callback
+ * @event - the event for which to register a callback
+ */
+void dln2_unregister_event_cb(struct platform_device *pdev, u16 event);
+
+/**
+ * dln2_transfer - issue a DLN2 command and wait for a response and
+ * the associated data
+ *
+ * @pdev - the sub-device which is issuing this transfer
+ * @cmd - the command to be sent to the device
+ * @obuf - the buffer to be sent to the device; it can be NULL if the
+ * user doesn't need to transmit data with this command
+ * @obuf_len - the size of the buffer to be sent to the device
+ * @ibuf - any data associated with the response will be copied here;
+ * it can be NULL if the user doesn't need the response data
+ * @ibuf_len - must be initialized to the input buffer size; it will
+ * be modified to indicate the actual data transfered;
+ * @result - pointer to store the result code received from hardware;
+ * it can be NULL if the user doesn't need the result code
+ *
+ * @return 0 for success, negative value for errors
+ */
+int dln2_transfer(struct platform_device *pdev, u16 cmd,
+ const void *obuf, unsigned obuf_len,
+ void *ibuf, unsigned *ibuf_len, u16 *result);
+
+#endif
--
1.9.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* Re: [PATCH v8 1/4] mfd: add support for Diolan DLN-2 devices
2014-10-15 14:48 ` [PATCH v8 1/4] mfd: add support for Diolan DLN-2 devices Octavian Purdila
@ 2014-10-23 15:16 ` Johan Hovold
2014-10-27 13:21 ` Octavian Purdila
0 siblings, 1 reply; 14+ messages in thread
From: Johan Hovold @ 2014-10-23 15:16 UTC (permalink / raw)
To: Octavian Purdila
Cc: gregkh, linus.walleij, gnurou, wsa, sameo, lee.jones, arnd, johan,
daniel.baluta, laurentiu.palcu, linux-usb, linux-kernel,
linux-gpio, linux-i2c
On Wed, Oct 15, 2014 at 05:48:08PM +0300, Octavian Purdila wrote:
Here's some late feedback due to travels. You managed to get two updates
in there so commenting on the diff from v6.
> +struct dln2_event_cb_entry {
> + struct list_head list;
> + u16 id;
> + struct platform_device *pdev;
> + dln2_event_cb_t callback;
> +};
> +
> +int dln2_register_event_cb(struct platform_device *pdev, u16 id,
> + dln2_event_cb_t rx_cb)
> +{
> + struct dln2_dev *dln2 = dev_get_drvdata(pdev->dev.parent);
> + struct dln2_event_cb_entry *i, *new_cb;
Can you use a name which does not have the same suffix as the actual
callback function (i.e. "_cb"). Just call it "entry" or something.
> + unsigned long flags;
> + int ret = 0;
> +
> + new_cb = kmalloc(sizeof(*new_cb), GFP_KERNEL);
Use kzalloc here.
> + if (!new_cb)
> + return -ENOMEM;
> +
> + new_cb->id = id;
> + new_cb->callback = rx_cb;
> + new_cb->pdev = pdev;
> +
> + spin_lock_irqsave(&dln2->event_cb_lock, flags);
> +
> + list_for_each_entry(i, &dln2->event_cb_list, list) {
> + if (i->id == id) {
> + ret = -EBUSY;
> + break;
> + }
> + }
> +
> + if (!ret)
> + list_add_rcu(&new_cb->list, &dln2->event_cb_list);
> +
> + spin_unlock_irqrestore(&dln2->event_cb_lock, flags);
> +
> + if (ret)
> + kfree(new_cb);
> +
> + return ret;
> +}
> +EXPORT_SYMBOL(dln2_register_event_cb);
> +
> +void dln2_unregister_event_cb(struct platform_device *pdev, u16 id)
> +{
> + struct dln2_dev *dln2 = dev_get_drvdata(pdev->dev.parent);
> + struct dln2_event_cb_entry *i;
> + unsigned long flags;
> + bool found = false;
> +
> + spin_lock_irqsave(&dln2->event_cb_lock, flags);
> +
> + list_for_each_entry(i, &dln2->event_cb_list, list) {
> + if (i->id == id) {
> + list_del_rcu(&i->list);
> + found = true;
> + break;
> + }
> + }
> +
> + spin_unlock_irqrestore(&dln2->event_cb_lock, flags);
> +
> + if (found) {
> + synchronize_rcu();
> + kfree(i);
> + }
> +}
> +EXPORT_SYMBOL(dln2_unregister_event_cb);
> +
Please add a comment describing the return value (i.e. when the urb had
been saved and shouldn't be resubmitted).
Also could rename this helper so it doesn't appear to be a variant of
dln2_transfer (e.g. something with "complete" in the name).
> +static bool dln2_rx_transfer(struct dln2_dev *dln2, struct urb *urb,
> + u16 handle, u16 rx_slot)
> +{
> + struct dln2_mod_rx_slots *rxs = &dln2->mod_rx_slots[handle];
> + struct dln2_rx_context *rxc;
> + bool ret = false;
> +
> + rxc = &rxs->slots[rx_slot];
> +
> + /*
> + * No need to disable interrupts as this lock is not taken in
> + * interrupt context elsewhere in this driver and this
> + * function (or its callers) are not exported to other
> + * modules.
Why do you break comment lines already at 70 chars?
> + */
> + spin_lock(&rxs->lock);
> + if (rxc->in_use && !rxc->urb) {
> + rxc->urb = urb;
> + complete(&rxc->done);
> + ret = true;
> + }
> + spin_unlock(&rxs->lock);
> +
> + return ret;
> +}
> +
> +static void dln2_run_event_callbacks(struct dln2_dev *dln2, u16 id, u16 echo,
> + void *data, int len)
> +{
> + struct dln2_event_cb_entry *i;
> +
> + rcu_read_lock();
> +
> + list_for_each_entry_rcu(i, &dln2->event_cb_list, list)
> + if (i->id == id)
> + i->callback(i->pdev, echo, data, len);
> +
> + rcu_read_unlock();
> +}
> +
> +static void dln2_rx(struct urb *urb)
> +{
> + struct dln2_dev *dln2 = urb->context;
> + struct dln2_header *hdr = urb->transfer_buffer;
> + struct device *dev = &dln2->interface->dev;
> + u16 id, echo, handle, size;
> + u8 *data;
> + int len;
> + int err;
> +
> + switch (urb->status) {
> + case 0:
> + /* success */
> + break;
> + case -ECONNRESET:
> + case -ENOENT:
> + case -ESHUTDOWN:
> + case -EPIPE:
> + /* this urb is terminated, clean up */
> + dev_dbg(dev, "urb shutting down with status %d\n", urb->status);
> + return;
> + default:
> + dev_dbg(dev, "nonzero urb status received %d\n", urb->status);
> + goto out;
> + }
> +
> + if (urb->actual_length < sizeof(struct dln2_header)) {
> + dev_err(dev, "short response: %d\n", urb->actual_length);
> + goto out;
> + }
> +
> + handle = le16_to_cpu(hdr->handle);
> + id = le16_to_cpu(hdr->id);
> + echo = le16_to_cpu(hdr->echo);
> + size = le16_to_cpu(hdr->size);
> +
> + if (size != urb->actual_length) {
> + dev_err(dev, "size mismatch: handle %x cmd %x echo %x size %d actual %d\n",
> + handle, id, echo, size, urb->actual_length);
> + goto out;
> + }
> +
> + if (handle >= DLN2_HANDLES) {
> + dev_warn(dev, "RX: invalid handle %d\n", handle);
> + goto out;
> + }
> +
> + data = urb->transfer_buffer + sizeof(struct dln2_header);
> + len = urb->actual_length - sizeof(struct dln2_header);
> +
> + if (handle == DLN2_HANDLE_EVENT) {
> + dln2_run_event_callbacks(dln2, id, echo, data, len);
> + } else {
> + /* URB will be re-submitted in free_rx_slot */
Refer to _dln2_transfer (the only place where free_rx_slot is used) as
well.
> + if (dln2_rx_transfer(dln2, urb, handle, echo))
> + return;
> + dev_warn(dev, "bad/late response %d/%d\n", handle, echo);
Move this message back to the helper.
> + }
> +
> +out:
> + err = usb_submit_urb(urb, GFP_ATOMIC);
> + if (err < 0)
> + dev_err(dev, "failed to resubmit RX URB: %d\n", err);
> +}
> +
[...]
> +static int dln2_setup_rx_urbs(struct dln2_dev *dln2,
> + struct usb_host_interface *hostif)
> +{
> + int i;
> + const int rx_max_size = DLN2_RX_BUF_SIZE;
> +
> + for (i = 0; i < DLN2_MAX_URBS; i++) {
> + int ret;
> + struct device *dev = &dln2->interface->dev;
Move these out of the loop.
> +
> + dln2->rx_buf[i] = kmalloc(rx_max_size, GFP_KERNEL);
> + if (!dln2->rx_buf[i])
> + return -ENOMEM;
> +
> + dln2->rx_urb[i] = usb_alloc_urb(0, GFP_KERNEL);
> + if (!dln2->rx_urb[i])
> + return -ENOMEM;
> +
> + usb_fill_bulk_urb(dln2->rx_urb[i], dln2->usb_dev,
> + usb_rcvbulkpipe(dln2->usb_dev, dln2->ep_in),
> + dln2->rx_buf[i], rx_max_size, dln2_rx, dln2);
> +
> + ret = usb_submit_urb(dln2->rx_urb[i], GFP_KERNEL);
> + if (ret < 0) {
> + dev_err(dev, "failed to submit RX URB: %d\n", ret);
> + return ret;
> + }
> + }
> +
> + return 0;
> +}
> +
> +static struct dln2_platform_data dln2_pdata_gpio = {
> + .handle = DLN2_HANDLE_GPIO,
> +};
> +
> +/* Only one I2C port seems to be supported on current hardware */
> +static struct dln2_platform_data dln2_pdata_i2c = {
> + .handle = DLN2_HANDLE_I2C,
> + .port = 0,
> +};
> +
> +static const struct mfd_cell dln2_devs[] = {
> + {
> + .name = "dln2-gpio",
> + .platform_data = &dln2_pdata_gpio,
> + .pdata_size = sizeof(struct dln2_platform_data),
> + },
> + {
> + .name = "dln2-i2c",
> + .platform_data = &dln2_pdata_i2c,
> + .pdata_size = sizeof(struct dln2_platform_data),
> + },
> +};
> +
> +static void dln2_disconnect(struct usb_interface *interface)
> +{
> + struct dln2_dev *dln2 = usb_get_intfdata(interface);
> + int i, j;
> +
> + /* don't allow starting new transfers */
> + spin_lock(&dln2->disconnect_lock);
> + dln2->disconnect = true;
> + spin_unlock(&dln2->disconnect_lock);
> +
> + /* cancel in progress transfers */
> + for (i = 0; i < DLN2_HANDLES; i++) {
> + struct dln2_mod_rx_slots *rxs = &dln2->mod_rx_slots[i];
> + unsigned long flags;
> +
> + spin_lock_irqsave(&rxs->lock, flags);
> +
> + /* cancel all response waiters */
> + for (j = 0; j < DLN2_MAX_RX_SLOTS; j++) {
> + struct dln2_rx_context *rxc = &rxs->slots[j];
> +
> + if (rxc->in_use)
> + complete(&rxc->done);
> + }
> +
> + spin_unlock_irqrestore(&rxs->lock, flags);
> + }
> +
> + /* wait for transfers to end */
> + wait_event(dln2->disconnect_wq, !dln2->active_transfers);
> +
> + mfd_remove_devices(&interface->dev);
> +
> + dln2_free(dln2);
> +}
> +
> +static int dln2_probe(struct usb_interface *interface,
> + const struct usb_device_id *usb_id)
> +{
> + struct usb_host_interface *hostif = interface->cur_altsetting;
> + struct device *dev = &interface->dev;
> + struct dln2_dev *dln2;
> + int ret;
> + int i, j;
> +
> + if (hostif->desc.bInterfaceNumber != 0 ||
> + hostif->desc.bNumEndpoints < 2)
> + return -ENODEV;
> +
> + dln2 = kzalloc(sizeof(*dln2), GFP_KERNEL);
> + if (!dln2)
> + return -ENOMEM;
> +
> + dln2->ep_out = hostif->endpoint[0].desc.bEndpointAddress;
> + dln2->ep_in = hostif->endpoint[1].desc.bEndpointAddress;
> + dln2->usb_dev = usb_get_dev(interface_to_usbdev(interface));
> + dln2->interface = interface;
> + usb_set_intfdata(interface, dln2);
> + init_waitqueue_head(&dln2->disconnect_wq);
> +
> + for (i = 0; i < DLN2_HANDLES; i++) {
> + init_waitqueue_head(&dln2->mod_rx_slots[i].wq);
> + spin_lock_init(&dln2->mod_rx_slots[i].lock);
> + for (j = 0; j < DLN2_MAX_RX_SLOTS; j++)
> + init_completion(&dln2->mod_rx_slots[i].slots[j].done);
> + }
> +
> + spin_lock_init(&dln2->event_cb_lock);
> + spin_lock_init(&dln2->disconnect_lock);
> + INIT_LIST_HEAD(&dln2->event_cb_list);
> +
> + ret = dln2_setup_rx_urbs(dln2, hostif);
> + if (ret)
> + goto out_cleanup;
> +
> + ret = dln2_hw_init(dln2);
> + if (ret < 0) {
> + dev_err(dev, "failed to initialize hardware\n");
> + goto out_cleanup;
> + }
> +
> + ret = mfd_add_hotplug_devices(dev, dln2_devs, ARRAY_SIZE(dln2_devs));
So this now depends on 15bb4d6e8534 ("mfd: core: Add helper function to
register hotplug devices") in the MFD tree.
Please mention what tree the patch is against in your cover letter (I
noticed you had rebased when it no longer applied to 3.17).
You should drop the gpiolib patch now that v3.18-rc1 is out as well.
> + if (ret != 0) {
> + dev_err(dev, "failed to add mfd devices to core\n");
> + goto out_cleanup;
> + }
> +
> + return 0;
> +
> +out_cleanup:
> + dln2_free(dln2);
> +
> + return ret;
> +}
> +
> +static const struct usb_device_id dln2_table[] = {
> + { USB_DEVICE(0xa257, 0x2013) },
> + { }
> +};
> +
> +MODULE_DEVICE_TABLE(usb, dln2_table);
> +
> +static struct usb_driver dln2_driver = {
> + .name = "dln2",
> + .probe = dln2_probe,
> + .disconnect = dln2_disconnect,
> + .id_table = dln2_table,
> +};
> +
> +module_usb_driver(dln2_driver);
> +
> +MODULE_AUTHOR("Octavian Purdila <octavian.purdila@intel.com>");
> +MODULE_DESCRIPTION("Core driver for the Diolan DLN2 interface adapter");
> +MODULE_LICENSE("GPL v2");
> diff --git a/include/linux/mfd/dln2.h b/include/linux/mfd/dln2.h
> new file mode 100644
> index 0000000..57ddc58
> --- /dev/null
> +++ b/include/linux/mfd/dln2.h
> @@ -0,0 +1,69 @@
> +#ifndef __LINUX_USB_DLN2_H
> +#define __LINUX_USB_DLN2_H
> +
> +#define DLN2_CMD(cmd, id) ((cmd) | ((id) << 8))
> +
> +struct dln2_platform_data {
> + u16 handle; /* sub-driver handle (internally used only) */
> + u8 port; /* I2C/SPI port */
> +};
> +
> +/**
> + * dln2_event_cb_t - event callback function signature
> + *
> + * @pdev - the sub-device that registered this callback
> + * @echo - the echo header field received in the message
> + * @data - the data payload
> + * @len - the data payload length
> + *
> + * The callback function is called in interrupt context and the data
> + * payload is only valid during the call. If the user needs later
> + * access of the data, it must copy it.
> + */
> +
> +typedef void (*dln2_event_cb_t)(struct platform_device *pdev, u16 echo,
> + const void *data, int len);
> +
> +/**
> + * dl2n_register_event_cb - register a callback function for an event
> + *
> + * @pdev - the sub-device that registers the callback
> + * @event - the event for which to register a callback
> + * @event_cb - the callback function
> + *
> + * @return 0 in case of success, negative value in case of error
> + */
> +int dln2_register_event_cb(struct platform_device *pdev, u16 event,
> + dln2_event_cb_t event_cb);
> +
> +/**
> + * dln2_unregister_event_cb - unregister the callback function for an event
> + *
> + * @pdev - the sub-device that registered the callback
> + * @event - the event for which to register a callback
> + */
> +void dln2_unregister_event_cb(struct platform_device *pdev, u16 event);
> +
> +/**
> + * dln2_transfer - issue a DLN2 command and wait for a response and
> + * the associated data
> + *
> + * @pdev - the sub-device which is issuing this transfer
> + * @cmd - the command to be sent to the device
> + * @obuf - the buffer to be sent to the device; it can be NULL if the
> + * user doesn't need to transmit data with this command
> + * @obuf_len - the size of the buffer to be sent to the device
> + * @ibuf - any data associated with the response will be copied here;
> + * it can be NULL if the user doesn't need the response data
> + * @ibuf_len - must be initialized to the input buffer size; it will
> + * be modified to indicate the actual data transfered;
> + * @result - pointer to store the result code received from hardware;
> + * it can be NULL if the user doesn't need the result code
> + *
> + * @return 0 for success, negative value for errors
> + */
> +int dln2_transfer(struct platform_device *pdev, u16 cmd,
> + const void *obuf, unsigned obuf_len,
> + void *ibuf, unsigned *ibuf_len, u16 *result);
Why add yet another parameter for the result and then never even use it?
Please remove it. You can add a new function for it (and a wrapper)
later if it's ever needed.
You should also consider adding a convenience function for when you
don't care about any returned data (e.g. dln2_transfer_tx) so you don't
have to pass all those NULLs (most calls currently have three NULL
params).
> +
> +#endif
Johan
^ permalink raw reply [flat|nested] 14+ messages in thread* Re: [PATCH v8 1/4] mfd: add support for Diolan DLN-2 devices
2014-10-23 15:16 ` Johan Hovold
@ 2014-10-27 13:21 ` Octavian Purdila
2014-10-27 14:36 ` Johan Hovold
0 siblings, 1 reply; 14+ messages in thread
From: Octavian Purdila @ 2014-10-27 13:21 UTC (permalink / raw)
To: Johan Hovold
Cc: Greg Kroah-Hartman, Linus Walleij, Alexandre Courbot,
Wolfram Sang, Samuel Ortiz, Lee Jones, Arnd Bergmann,
Daniel Baluta, Laurentiu Palcu,
linux-usb-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, lkml,
linux-gpio-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, linux-i2c
On Thu, Oct 23, 2014 at 6:16 PM, Johan Hovold <johan-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org> wrote:
>
> On Wed, Oct 15, 2014 at 05:48:08PM +0300, Octavian Purdila wrote:
>
> Here's some late feedback due to travels. You managed to get two updates
> in there so commenting on the diff from v6.
>
Thanks for the review :)
> > +struct dln2_event_cb_entry {
> > + struct list_head list;
> > + u16 id;
> > + struct platform_device *pdev;
> > + dln2_event_cb_t callback;
> > +};
> > +
> > +int dln2_register_event_cb(struct platform_device *pdev, u16 id,
> > + dln2_event_cb_t rx_cb)
> > +{
> > + struct dln2_dev *dln2 = dev_get_drvdata(pdev->dev.parent);
> > + struct dln2_event_cb_entry *i, *new_cb;
>
> Can you use a name which does not have the same suffix as the actual
> callback function (i.e. "_cb"). Just call it "entry" or something.
>
OK.
> > + unsigned long flags;
> > + int ret = 0;
> > +
> > + new_cb = kmalloc(sizeof(*new_cb), GFP_KERNEL);
>
> Use kzalloc here.
Why kzalloc? All of the fields are initialized below.
>
> > + if (!new_cb)
> > + return -ENOMEM;
> > +
> > + new_cb->id = id;
> > + new_cb->callback = rx_cb;
> > + new_cb->pdev = pdev;
> > +
> > + spin_lock_irqsave(&dln2->event_cb_lock, flags);
> > +
> > + list_for_each_entry(i, &dln2->event_cb_list, list) {
> > + if (i->id == id) {
> > + ret = -EBUSY;
> > + break;
> > + }
> > + }
> > +
> > + if (!ret)
> > + list_add_rcu(&new_cb->list, &dln2->event_cb_list);
> > +
> > + spin_unlock_irqrestore(&dln2->event_cb_lock, flags);
> > +
> > + if (ret)
> > + kfree(new_cb);
> > +
> > + return ret;
> > +}
> > +EXPORT_SYMBOL(dln2_register_event_cb);
> > +
> > +void dln2_unregister_event_cb(struct platform_device *pdev, u16 id)
> > +{
> > + struct dln2_dev *dln2 = dev_get_drvdata(pdev->dev.parent);
> > + struct dln2_event_cb_entry *i;
> > + unsigned long flags;
> > + bool found = false;
> > +
> > + spin_lock_irqsave(&dln2->event_cb_lock, flags);
> > +
> > + list_for_each_entry(i, &dln2->event_cb_list, list) {
> > + if (i->id == id) {
> > + list_del_rcu(&i->list);
> > + found = true;
> > + break;
> > + }
> > + }
> > +
> > + spin_unlock_irqrestore(&dln2->event_cb_lock, flags);
> > +
> > + if (found) {
> > + synchronize_rcu();
> > + kfree(i);
> > + }
> > +}
> > +EXPORT_SYMBOL(dln2_unregister_event_cb);
> > +
>
> Please add a comment describing the return value (i.e. when the urb had
> been saved and shouldn't be resubmitted).
>
> Also could rename this helper so it doesn't appear to be a variant of
> dln2_transfer (e.g. something with "complete" in the name).
>
Ok, I will use dln2_transfer_complete.
> > +static bool dln2_rx_transfer(struct dln2_dev *dln2, struct urb *urb,
> > + u16 handle, u16 rx_slot)
> > +{
> > + struct dln2_mod_rx_slots *rxs = &dln2->mod_rx_slots[handle];
> > + struct dln2_rx_context *rxc;
> > + bool ret = false;
> > +
> > + rxc = &rxs->slots[rx_slot];
> > +
> > + /*
> > + * No need to disable interrupts as this lock is not taken in
> > + * interrupt context elsewhere in this driver and this
> > + * function (or its callers) are not exported to other
> > + * modules.
>
> Why do you break comment lines already at 70 chars?
>
Oops, relic in my .emacs, will fix all comments in v9.
> > + */
> > + spin_lock(&rxs->lock);
> > + if (rxc->in_use && !rxc->urb) {
> > + rxc->urb = urb;
> > + complete(&rxc->done);
> > + ret = true;
> > + }
> > + spin_unlock(&rxs->lock);
> > +
> > + return ret;
> > +}
> > +
> > +static void dln2_run_event_callbacks(struct dln2_dev *dln2, u16 id, u16 echo,
> > + void *data, int len)
> > +{
> > + struct dln2_event_cb_entry *i;
> > +
> > + rcu_read_lock();
> > +
> > + list_for_each_entry_rcu(i, &dln2->event_cb_list, list)
> > + if (i->id == id)
> > + i->callback(i->pdev, echo, data, len);
> > +
> > + rcu_read_unlock();
> > +}
> > +
> > +static void dln2_rx(struct urb *urb)
> > +{
> > + struct dln2_dev *dln2 = urb->context;
> > + struct dln2_header *hdr = urb->transfer_buffer;
> > + struct device *dev = &dln2->interface->dev;
> > + u16 id, echo, handle, size;
> > + u8 *data;
> > + int len;
> > + int err;
> > +
> > + switch (urb->status) {
> > + case 0:
> > + /* success */
> > + break;
> > + case -ECONNRESET:
> > + case -ENOENT:
> > + case -ESHUTDOWN:
> > + case -EPIPE:
> > + /* this urb is terminated, clean up */
> > + dev_dbg(dev, "urb shutting down with status %d\n", urb->status);
> > + return;
> > + default:
> > + dev_dbg(dev, "nonzero urb status received %d\n", urb->status);
> > + goto out;
> > + }
> > +
> > + if (urb->actual_length < sizeof(struct dln2_header)) {
> > + dev_err(dev, "short response: %d\n", urb->actual_length);
> > + goto out;
> > + }
> > +
> > + handle = le16_to_cpu(hdr->handle);
> > + id = le16_to_cpu(hdr->id);
> > + echo = le16_to_cpu(hdr->echo);
> > + size = le16_to_cpu(hdr->size);
> > +
> > + if (size != urb->actual_length) {
> > + dev_err(dev, "size mismatch: handle %x cmd %x echo %x size %d actual %d\n",
> > + handle, id, echo, size, urb->actual_length);
> > + goto out;
> > + }
> > +
> > + if (handle >= DLN2_HANDLES) {
> > + dev_warn(dev, "RX: invalid handle %d\n", handle);
> > + goto out;
> > + }
> > +
> > + data = urb->transfer_buffer + sizeof(struct dln2_header);
> > + len = urb->actual_length - sizeof(struct dln2_header);
> > +
> > + if (handle == DLN2_HANDLE_EVENT) {
> > + dln2_run_event_callbacks(dln2, id, echo, data, len);
> > + } else {
> > + /* URB will be re-submitted in free_rx_slot */
>
> Refer to _dln2_transfer (the only place where free_rx_slot is used) as
> well.
>
OK.
> > + if (dln2_rx_transfer(dln2, urb, handle, echo))
> > + return;
> > + dev_warn(dev, "bad/late response %d/%d\n", handle, echo);
>
> Move this message back to the helper.
>
OK.
> > + }
> > +
> > +out:
> > + err = usb_submit_urb(urb, GFP_ATOMIC);
> > + if (err < 0)
> > + dev_err(dev, "failed to resubmit RX URB: %d\n", err);
> > +}
> > +
>
> [...]
>
> > +static int dln2_setup_rx_urbs(struct dln2_dev *dln2,
> > + struct usb_host_interface *hostif)
> > +{
> > + int i;
> > + const int rx_max_size = DLN2_RX_BUF_SIZE;
> > +
> > + for (i = 0; i < DLN2_MAX_URBS; i++) {
> > + int ret;
> > + struct device *dev = &dln2->interface->dev;
>
> Move these out of the loop.
>
> > +
> > + dln2->rx_buf[i] = kmalloc(rx_max_size, GFP_KERNEL);
> > + if (!dln2->rx_buf[i])
> > + return -ENOMEM;
> > +
> > + dln2->rx_urb[i] = usb_alloc_urb(0, GFP_KERNEL);
> > + if (!dln2->rx_urb[i])
> > + return -ENOMEM;
> > +
> > + usb_fill_bulk_urb(dln2->rx_urb[i], dln2->usb_dev,
> > + usb_rcvbulkpipe(dln2->usb_dev, dln2->ep_in),
> > + dln2->rx_buf[i], rx_max_size, dln2_rx, dln2);
> > +
> > + ret = usb_submit_urb(dln2->rx_urb[i], GFP_KERNEL);
> > + if (ret < 0) {
> > + dev_err(dev, "failed to submit RX URB: %d\n", ret);
> > + return ret;
> > + }
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static struct dln2_platform_data dln2_pdata_gpio = {
> > + .handle = DLN2_HANDLE_GPIO,
> > +};
> > +
> > +/* Only one I2C port seems to be supported on current hardware */
> > +static struct dln2_platform_data dln2_pdata_i2c = {
> > + .handle = DLN2_HANDLE_I2C,
> > + .port = 0,
> > +};
> > +
> > +static const struct mfd_cell dln2_devs[] = {
> > + {
> > + .name = "dln2-gpio",
> > + .platform_data = &dln2_pdata_gpio,
> > + .pdata_size = sizeof(struct dln2_platform_data),
> > + },
> > + {
> > + .name = "dln2-i2c",
> > + .platform_data = &dln2_pdata_i2c,
> > + .pdata_size = sizeof(struct dln2_platform_data),
> > + },
> > +};
> > +
> > +static void dln2_disconnect(struct usb_interface *interface)
> > +{
> > + struct dln2_dev *dln2 = usb_get_intfdata(interface);
> > + int i, j;
> > +
> > + /* don't allow starting new transfers */
> > + spin_lock(&dln2->disconnect_lock);
> > + dln2->disconnect = true;
> > + spin_unlock(&dln2->disconnect_lock);
> > +
> > + /* cancel in progress transfers */
> > + for (i = 0; i < DLN2_HANDLES; i++) {
> > + struct dln2_mod_rx_slots *rxs = &dln2->mod_rx_slots[i];
> > + unsigned long flags;
> > +
> > + spin_lock_irqsave(&rxs->lock, flags);
> > +
> > + /* cancel all response waiters */
> > + for (j = 0; j < DLN2_MAX_RX_SLOTS; j++) {
> > + struct dln2_rx_context *rxc = &rxs->slots[j];
> > +
> > + if (rxc->in_use)
> > + complete(&rxc->done);
> > + }
> > +
> > + spin_unlock_irqrestore(&rxs->lock, flags);
> > + }
> > +
> > + /* wait for transfers to end */
> > + wait_event(dln2->disconnect_wq, !dln2->active_transfers);
> > +
> > + mfd_remove_devices(&interface->dev);
> > +
> > + dln2_free(dln2);
> > +}
> > +
> > +static int dln2_probe(struct usb_interface *interface,
> > + const struct usb_device_id *usb_id)
> > +{
> > + struct usb_host_interface *hostif = interface->cur_altsetting;
> > + struct device *dev = &interface->dev;
> > + struct dln2_dev *dln2;
> > + int ret;
> > + int i, j;
> > +
> > + if (hostif->desc.bInterfaceNumber != 0 ||
> > + hostif->desc.bNumEndpoints < 2)
> > + return -ENODEV;
> > +
> > + dln2 = kzalloc(sizeof(*dln2), GFP_KERNEL);
> > + if (!dln2)
> > + return -ENOMEM;
> > +
> > + dln2->ep_out = hostif->endpoint[0].desc.bEndpointAddress;
> > + dln2->ep_in = hostif->endpoint[1].desc.bEndpointAddress;
> > + dln2->usb_dev = usb_get_dev(interface_to_usbdev(interface));
> > + dln2->interface = interface;
> > + usb_set_intfdata(interface, dln2);
> > + init_waitqueue_head(&dln2->disconnect_wq);
> > +
> > + for (i = 0; i < DLN2_HANDLES; i++) {
> > + init_waitqueue_head(&dln2->mod_rx_slots[i].wq);
> > + spin_lock_init(&dln2->mod_rx_slots[i].lock);
> > + for (j = 0; j < DLN2_MAX_RX_SLOTS; j++)
> > + init_completion(&dln2->mod_rx_slots[i].slots[j].done);
> > + }
> > +
> > + spin_lock_init(&dln2->event_cb_lock);
> > + spin_lock_init(&dln2->disconnect_lock);
> > + INIT_LIST_HEAD(&dln2->event_cb_list);
> > +
> > + ret = dln2_setup_rx_urbs(dln2, hostif);
> > + if (ret)
> > + goto out_cleanup;
> > +
> > + ret = dln2_hw_init(dln2);
> > + if (ret < 0) {
> > + dev_err(dev, "failed to initialize hardware\n");
> > + goto out_cleanup;
> > + }
> > +
> > + ret = mfd_add_hotplug_devices(dev, dln2_devs, ARRAY_SIZE(dln2_devs));
>
> So this now depends on 15bb4d6e8534 ("mfd: core: Add helper function to
> register hotplug devices") in the MFD tree.
>
> Please mention what tree the patch is against in your cover letter (I
> noticed you had rebased when it no longer applied to 3.17).
>
> You should drop the gpiolib patch now that v3.18-rc1 is out as well.
This series is based against the Lee's for-mfd-next-v3.19 tree that
does not yet contain the gpiolib patch.
>
> > + if (ret != 0) {
> > + dev_err(dev, "failed to add mfd devices to core\n");
> > + goto out_cleanup;
> > + }
> > +
> > + return 0;
> > +
> > +out_cleanup:
> > + dln2_free(dln2);
> > +
> > + return ret;
> > +}
> > +
> > +static const struct usb_device_id dln2_table[] = {
> > + { USB_DEVICE(0xa257, 0x2013) },
> > + { }
> > +};
> > +
> > +MODULE_DEVICE_TABLE(usb, dln2_table);
> > +
> > +static struct usb_driver dln2_driver = {
> > + .name = "dln2",
> > + .probe = dln2_probe,
> > + .disconnect = dln2_disconnect,
> > + .id_table = dln2_table,
> > +};
> > +
> > +module_usb_driver(dln2_driver);
> > +
> > +MODULE_AUTHOR("Octavian Purdila <octavian.purdila-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>");
> > +MODULE_DESCRIPTION("Core driver for the Diolan DLN2 interface adapter");
> > +MODULE_LICENSE("GPL v2");
> > diff --git a/include/linux/mfd/dln2.h b/include/linux/mfd/dln2.h
> > new file mode 100644
> > index 0000000..57ddc58
> > --- /dev/null
> > +++ b/include/linux/mfd/dln2.h
> > @@ -0,0 +1,69 @@
> > +#ifndef __LINUX_USB_DLN2_H
> > +#define __LINUX_USB_DLN2_H
> > +
> > +#define DLN2_CMD(cmd, id) ((cmd) | ((id) << 8))
> > +
> > +struct dln2_platform_data {
> > + u16 handle; /* sub-driver handle (internally used only) */
> > + u8 port; /* I2C/SPI port */
> > +};
> > +
> > +/**
> > + * dln2_event_cb_t - event callback function signature
> > + *
> > + * @pdev - the sub-device that registered this callback
> > + * @echo - the echo header field received in the message
> > + * @data - the data payload
> > + * @len - the data payload length
> > + *
> > + * The callback function is called in interrupt context and the data
> > + * payload is only valid during the call. If the user needs later
> > + * access of the data, it must copy it.
> > + */
> > +
> > +typedef void (*dln2_event_cb_t)(struct platform_device *pdev, u16 echo,
> > + const void *data, int len);
> > +
> > +/**
> > + * dl2n_register_event_cb - register a callback function for an event
> > + *
> > + * @pdev - the sub-device that registers the callback
> > + * @event - the event for which to register a callback
> > + * @event_cb - the callback function
> > + *
> > + * @return 0 in case of success, negative value in case of error
> > + */
> > +int dln2_register_event_cb(struct platform_device *pdev, u16 event,
> > + dln2_event_cb_t event_cb);
> > +
> > +/**
> > + * dln2_unregister_event_cb - unregister the callback function for an event
> > + *
> > + * @pdev - the sub-device that registered the callback
> > + * @event - the event for which to register a callback
> > + */
> > +void dln2_unregister_event_cb(struct platform_device *pdev, u16 event);
> > +
> > +/**
> > + * dln2_transfer - issue a DLN2 command and wait for a response and
> > + * the associated data
> > + *
> > + * @pdev - the sub-device which is issuing this transfer
> > + * @cmd - the command to be sent to the device
> > + * @obuf - the buffer to be sent to the device; it can be NULL if the
> > + * user doesn't need to transmit data with this command
> > + * @obuf_len - the size of the buffer to be sent to the device
> > + * @ibuf - any data associated with the response will be copied here;
> > + * it can be NULL if the user doesn't need the response data
> > + * @ibuf_len - must be initialized to the input buffer size; it will
> > + * be modified to indicate the actual data transfered;
> > + * @result - pointer to store the result code received from hardware;
> > + * it can be NULL if the user doesn't need the result code
> > + *
> > + * @return 0 for success, negative value for errors
> > + */
> > +int dln2_transfer(struct platform_device *pdev, u16 cmd,
> > + const void *obuf, unsigned obuf_len,
> > + void *ibuf, unsigned *ibuf_len, u16 *result);
>
> Why add yet another parameter for the result and then never even use it?
> Please remove it. You can add a new function for it (and a wrapper)
> later if it's ever needed.
>
It is needed for setting the frequency, but you are right I should add
it with that patch set.
> You should also consider adding a convenience function for when you
> don't care about any returned data (e.g. dln2_transfer_tx) so you don't
> have to pass all those NULLs (most calls currently have three NULL
> params).
>
OK, will do it in v9.
^ permalink raw reply [flat|nested] 14+ messages in thread* Re: [PATCH v8 1/4] mfd: add support for Diolan DLN-2 devices
2014-10-27 13:21 ` Octavian Purdila
@ 2014-10-27 14:36 ` Johan Hovold
0 siblings, 0 replies; 14+ messages in thread
From: Johan Hovold @ 2014-10-27 14:36 UTC (permalink / raw)
To: Octavian Purdila
Cc: Johan Hovold, Greg Kroah-Hartman, Linus Walleij,
Alexandre Courbot, Wolfram Sang, Samuel Ortiz, Lee Jones,
Arnd Bergmann, Daniel Baluta, Laurentiu Palcu,
linux-usb@vger.kernel.org, lkml, linux-gpio@vger.kernel.org,
linux-i2c
On Mon, Oct 27, 2014 at 03:21:10PM +0200, Octavian Purdila wrote:
> On Thu, Oct 23, 2014 at 6:16 PM, Johan Hovold <johan@kernel.org> wrote:
> > On Wed, Oct 15, 2014 at 05:48:08PM +0300, Octavian Purdila wrote:
> > > +struct dln2_event_cb_entry {
> > > + struct list_head list;
> > > + u16 id;
> > > + struct platform_device *pdev;
> > > + dln2_event_cb_t callback;
> > > +};
> > > +
> > > +int dln2_register_event_cb(struct platform_device *pdev, u16 id,
> > > + dln2_event_cb_t rx_cb)
> > > +{
> > > + struct dln2_dev *dln2 = dev_get_drvdata(pdev->dev.parent);
> > > + struct dln2_event_cb_entry *i, *new_cb;
> >
> > Can you use a name which does not have the same suffix as the actual
> > callback function (i.e. "_cb"). Just call it "entry" or something.
> >
>
> OK.
>
> > > + unsigned long flags;
> > > + int ret = 0;
> > > +
> > > + new_cb = kmalloc(sizeof(*new_cb), GFP_KERNEL);
> >
> > Use kzalloc here.
>
> Why kzalloc? All of the fields are initialized below.
It's good practise to clear any data structure at allocation. The cost
is negligible.
> > > + if (!new_cb)
> > > + return -ENOMEM;
> > > +
> > > + new_cb->id = id;
> > > + new_cb->callback = rx_cb;
> > > + new_cb->pdev = pdev;
> > > +
> > > + spin_lock_irqsave(&dln2->event_cb_lock, flags);
> > > +
> > > + list_for_each_entry(i, &dln2->event_cb_list, list) {
> > > + if (i->id == id) {
> > > + ret = -EBUSY;
> > > + break;
> > > + }
> > > + }
> > > +
> > > + if (!ret)
> > > + list_add_rcu(&new_cb->list, &dln2->event_cb_list);
> > > +
> > > + spin_unlock_irqrestore(&dln2->event_cb_lock, flags);
> > > +
> > > + if (ret)
> > > + kfree(new_cb);
> > > +
> > > + return ret;
> > > +}
> > > +EXPORT_SYMBOL(dln2_register_event_cb);
> > > + ret = mfd_add_hotplug_devices(dev, dln2_devs, ARRAY_SIZE(dln2_devs));
> >
> > So this now depends on 15bb4d6e8534 ("mfd: core: Add helper function to
> > register hotplug devices") in the MFD tree.
> >
> > Please mention what tree the patch is against in your cover letter (I
> > noticed you had rebased when it no longer applied to 3.17).
> >
> > You should drop the gpiolib patch now that v3.18-rc1 is out as well.
>
> This series is based against the Lee's for-mfd-next-v3.19 tree that
> does not yet contain the gpiolib patch.
Ok, but make sure to include that information in the cover letter.
Johan
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v8 2/4] i2c: add support for Diolan DLN-2 USB-I2C adapter
2014-10-15 14:48 [PATCH v8 0/4] mfd: add support for Diolan DLN-2 Octavian Purdila
2014-10-15 14:48 ` [PATCH v8 1/4] mfd: add support for Diolan DLN-2 devices Octavian Purdila
@ 2014-10-15 14:48 ` Octavian Purdila
[not found] ` <1413384491-23703-3-git-send-email-octavian.purdila-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
2014-10-15 14:48 ` [PATCH v8 3/4] gpiolib: add irq_not_threaded flag to gpio_chip Octavian Purdila
2014-10-15 14:48 ` [PATCH v8 4/4] gpio: add support for the Diolan DLN-2 USB GPIO driver Octavian Purdila
3 siblings, 1 reply; 14+ messages in thread
From: Octavian Purdila @ 2014-10-15 14:48 UTC (permalink / raw)
To: gregkh, linus.walleij, gnurou, wsa, sameo, lee.jones
Cc: arnd, johan, daniel.baluta, laurentiu.palcu, linux-usb,
linux-kernel, linux-gpio, linux-i2c, Octavian Purdila
From: Laurentiu Palcu <laurentiu.palcu@intel.com>
This patch adds support for the Diolan DLN-2 I2C master module. Due
to hardware limitations it does not support SMBUS quick commands.
Information about the USB protocol interface can be found in the
Programmer's Reference Manual [1], see section 6.2.2 for the I2C
master module commands and responses.
[1] https://www.diolan.com/downloads/dln-api-manual.pdf
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
---
drivers/i2c/busses/Kconfig | 10 ++
drivers/i2c/busses/Makefile | 1 +
drivers/i2c/busses/i2c-dln2.c | 270 ++++++++++++++++++++++++++++++++++++++++++
3 files changed, 281 insertions(+)
create mode 100644 drivers/i2c/busses/i2c-dln2.c
diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index 2ac87fa..2f3f371 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -858,6 +858,16 @@ config I2C_DIOLAN_U2C
This driver can also be built as a module. If so, the module
will be called i2c-diolan-u2c.
+config I2C_DLN2
+ tristate "Diolan DLN-2 USB I2C adapter"
+ depends on MFD_DLN2
+ help
+ If you say yes to this option, support will be included for Diolan
+ DLN2, a USB to I2C interface.
+
+ This driver can also be built as a module. If so, the module
+ will be called i2c-dln2.
+
config I2C_PARPORT
tristate "Parallel port adapter"
depends on PARPORT
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index 49bf07e..4755f79 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -85,6 +85,7 @@ obj-$(CONFIG_I2C_RCAR) += i2c-rcar.o
# External I2C/SMBus adapter drivers
obj-$(CONFIG_I2C_DIOLAN_U2C) += i2c-diolan-u2c.o
+obj-$(CONFIG_I2C_DLN2) += i2c-dln2.o
obj-$(CONFIG_I2C_PARPORT) += i2c-parport.o
obj-$(CONFIG_I2C_PARPORT_LIGHT) += i2c-parport-light.o
obj-$(CONFIG_I2C_ROBOTFUZZ_OSIF) += i2c-robotfuzz-osif.o
diff --git a/drivers/i2c/busses/i2c-dln2.c b/drivers/i2c/busses/i2c-dln2.c
new file mode 100644
index 0000000..62c38cd
--- /dev/null
+++ b/drivers/i2c/busses/i2c-dln2.c
@@ -0,0 +1,270 @@
+/*
+ * Driver for the Diolan DLN-2 USB-I2C adapter
+ *
+ * Copyright (c) 2014 Intel Corporation
+ *
+ * Derived from:
+ * i2c-diolan-u2c.c
+ * Copyright (c) 2010-2011 Ericsson AB
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation, version 2.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/slab.h>
+#include <linux/i2c.h>
+#include <linux/platform_device.h>
+#include <linux/mfd/dln2.h>
+
+#define DLN2_I2C_MODULE_ID 0x03
+#define DLN2_I2C_CMD(cmd) DLN2_CMD(cmd, DLN2_I2C_MODULE_ID)
+
+/* I2C commands */
+#define DLN2_I2C_GET_PORT_COUNT DLN2_I2C_CMD(0x00)
+#define DLN2_I2C_ENABLE DLN2_I2C_CMD(0x01)
+#define DLN2_I2C_DISABLE DLN2_I2C_CMD(0x02)
+#define DLN2_I2C_IS_ENABLED DLN2_I2C_CMD(0x03)
+#define DLN2_I2C_WRITE DLN2_I2C_CMD(0x06)
+#define DLN2_I2C_READ DLN2_I2C_CMD(0x07)
+#define DLN2_I2C_SCAN_DEVICES DLN2_I2C_CMD(0x08)
+#define DLN2_I2C_PULLUP_ENABLE DLN2_I2C_CMD(0x09)
+#define DLN2_I2C_PULLUP_DISABLE DLN2_I2C_CMD(0x0A)
+#define DLN2_I2C_PULLUP_IS_ENABLED DLN2_I2C_CMD(0x0B)
+#define DLN2_I2C_TRANSFER DLN2_I2C_CMD(0x0C)
+#define DLN2_I2C_SET_MAX_REPLY_COUNT DLN2_I2C_CMD(0x0D)
+#define DLN2_I2C_GET_MAX_REPLY_COUNT DLN2_I2C_CMD(0x0E)
+
+#define DLN2_I2C_MAX_XFER_SIZE 256
+#define DLN2_I2C_BUF_SIZE (DLN2_I2C_MAX_XFER_SIZE + 16)
+
+struct dln2_i2c {
+ struct platform_device *pdev;
+ struct i2c_adapter adapter;
+ u8 port;
+ /*
+ * Buffer to hold the packet for read or write transfers. One
+ * is enough since we can't have multiple transfers in
+ * parallel on the i2c adapter.
+ */
+ void *buf;
+};
+
+static int dln2_i2c_enable(struct dln2_i2c *dln2, bool enable)
+{
+ int ret;
+ u16 cmd;
+ struct {
+ u8 port;
+ } tx;
+
+ tx.port = dln2->port;
+
+ if (enable)
+ cmd = DLN2_I2C_ENABLE;
+ else
+ cmd = DLN2_I2C_DISABLE;
+
+ ret = dln2_transfer(dln2->pdev, cmd, &tx, sizeof(tx),
+ NULL, NULL, NULL);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+
+static int dln2_i2c_write(struct dln2_i2c *dln2, u8 addr,
+ u8 *data, u16 data_len)
+{
+ int ret;
+ struct {
+ u8 port;
+ u8 addr;
+ u8 mem_addr_len;
+ __le32 mem_addr;
+ __le16 buf_len;
+ u8 buf[DLN2_I2C_MAX_XFER_SIZE];
+ } __packed *tx = dln2->buf;
+ unsigned len;
+
+ BUILD_BUG_ON(sizeof(*tx) > DLN2_I2C_BUF_SIZE);
+
+ tx->port = dln2->port;
+ tx->addr = addr;
+ tx->mem_addr_len = 0;
+ tx->mem_addr = 0;
+ tx->buf_len = cpu_to_le16(data_len);
+ memcpy(tx->buf, data, data_len);
+
+ len = sizeof(*tx) + data_len - DLN2_I2C_MAX_XFER_SIZE;
+ ret = dln2_transfer(dln2->pdev, DLN2_I2C_WRITE, tx, len,
+ NULL, NULL, NULL);
+ if (ret < 0)
+ return ret;
+
+ return data_len;
+}
+
+static int dln2_i2c_read(struct dln2_i2c *dln2, u16 addr, u8 *data,
+ u16 data_len)
+{
+ int ret;
+ struct {
+ u8 port;
+ u8 addr;
+ u8 mem_addr_len;
+ __le32 mem_addr;
+ __le16 buf_len;
+ } __packed tx;
+ struct {
+ __le16 buf_len;
+ u8 buf[DLN2_I2C_MAX_XFER_SIZE];
+ } __packed *rx = dln2->buf;
+ unsigned rx_len = sizeof(*rx);
+
+ BUILD_BUG_ON(sizeof(*rx) > DLN2_I2C_BUF_SIZE);
+
+ tx.port = dln2->port;
+ tx.addr = addr;
+ tx.mem_addr_len = 0;
+ tx.mem_addr = 0;
+ tx.buf_len = cpu_to_le16(data_len);
+
+ ret = dln2_transfer(dln2->pdev, DLN2_I2C_READ, &tx, sizeof(tx),
+ rx, &rx_len, NULL);
+ if (ret < 0)
+ return ret;
+ if (rx_len < sizeof(rx->buf_len) + data_len)
+ return -EPROTO;
+ if (le16_to_cpu(rx->buf_len) != data_len)
+ return -EPROTO;
+
+ memcpy(data, rx->buf, data_len);
+
+ return data_len;
+}
+
+static int dln2_i2c_xfer(struct i2c_adapter *adapter,
+ struct i2c_msg *msgs, int num)
+{
+ struct dln2_i2c *dln2 = i2c_get_adapdata(adapter);
+ struct i2c_msg *pmsg;
+ struct device *dev = &dln2->pdev->dev;
+ int i;
+
+ for (i = 0; i < num; i++) {
+ int ret;
+
+ pmsg = &msgs[i];
+
+ if (pmsg->len > DLN2_I2C_MAX_XFER_SIZE) {
+ dev_warn(dev, "maximum transfer size exceeded\n");
+ return -EOPNOTSUPP;
+ }
+
+ if (pmsg->flags & I2C_M_RD) {
+ ret = dln2_i2c_read(dln2, pmsg->addr, pmsg->buf,
+ pmsg->len);
+ if (ret < 0)
+ return ret;
+
+ pmsg->len = ret;
+ } else {
+ ret = dln2_i2c_write(dln2, pmsg->addr, pmsg->buf,
+ pmsg->len);
+ if (ret != pmsg->len)
+ return -EPROTO;
+ }
+ }
+
+ return num;
+}
+
+static u32 dln2_i2c_func(struct i2c_adapter *a)
+{
+ return I2C_FUNC_I2C | I2C_FUNC_SMBUS_BYTE | I2C_FUNC_SMBUS_BYTE_DATA |
+ I2C_FUNC_SMBUS_WORD_DATA | I2C_FUNC_SMBUS_BLOCK_PROC_CALL |
+ I2C_FUNC_SMBUS_I2C_BLOCK;
+}
+
+static const struct i2c_algorithm dln2_i2c_usb_algorithm = {
+ .master_xfer = dln2_i2c_xfer,
+ .functionality = dln2_i2c_func,
+};
+
+static int dln2_i2c_probe(struct platform_device *pdev)
+{
+ int ret;
+ struct dln2_i2c *dln2;
+ struct device *dev = &pdev->dev;
+ struct dln2_platform_data *pdata = dev_get_platdata(&pdev->dev);
+
+ dln2 = devm_kzalloc(dev, sizeof(*dln2), GFP_KERNEL);
+ if (!dln2)
+ return -ENOMEM;
+
+ dln2->buf = devm_kmalloc(dev, DLN2_I2C_BUF_SIZE, GFP_KERNEL);
+ if (!dln2->buf)
+ return -ENOMEM;
+
+ dln2->pdev = pdev;
+ dln2->port = pdata->port;
+
+ /* setup i2c adapter description */
+ dln2->adapter.owner = THIS_MODULE;
+ dln2->adapter.class = I2C_CLASS_HWMON;
+ dln2->adapter.algo = &dln2_i2c_usb_algorithm;
+ dln2->adapter.dev.parent = dev;
+ i2c_set_adapdata(&dln2->adapter, dln2);
+ snprintf(dln2->adapter.name, sizeof(dln2->adapter.name), "%s-%s-%d",
+ "dln2-i2c", dev_name(pdev->dev.parent), dln2->port);
+
+ platform_set_drvdata(pdev, dln2);
+
+ /* initialize the i2c interface */
+ ret = dln2_i2c_enable(dln2, true);
+ if (ret < 0) {
+ dev_err(dev, "failed to initialize adapter: %d\n", ret);
+ return ret;
+ }
+
+ /* and finally attach to i2c layer */
+ ret = i2c_add_adapter(&dln2->adapter);
+ if (ret < 0) {
+ dev_err(dev, "failed to add I2C adapter: %d\n", ret);
+ goto out_disable;
+ }
+
+ return 0;
+
+out_disable:
+ dln2_i2c_enable(dln2, false);
+
+ return ret;
+}
+
+static int dln2_i2c_remove(struct platform_device *pdev)
+{
+ struct dln2_i2c *dln2 = platform_get_drvdata(pdev);
+
+ i2c_del_adapter(&dln2->adapter);
+ dln2_i2c_enable(dln2, false);
+
+ return 0;
+}
+
+static struct platform_driver dln2_i2c_driver = {
+ .driver.name = "dln2-i2c",
+ .probe = dln2_i2c_probe,
+ .remove = dln2_i2c_remove,
+};
+
+module_platform_driver(dln2_i2c_driver);
+
+MODULE_AUTHOR("Laurentiu Palcu <laurentiu.palcu@intel.com>");
+MODULE_DESCRIPTION("Driver for the Diolan DLN2 I2C master interface");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:dln2-i2c");
--
1.9.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v8 3/4] gpiolib: add irq_not_threaded flag to gpio_chip
2014-10-15 14:48 [PATCH v8 0/4] mfd: add support for Diolan DLN-2 Octavian Purdila
2014-10-15 14:48 ` [PATCH v8 1/4] mfd: add support for Diolan DLN-2 devices Octavian Purdila
2014-10-15 14:48 ` [PATCH v8 2/4] i2c: add support for Diolan DLN-2 USB-I2C adapter Octavian Purdila
@ 2014-10-15 14:48 ` Octavian Purdila
2014-10-20 5:08 ` Alexandre Courbot
2014-10-15 14:48 ` [PATCH v8 4/4] gpio: add support for the Diolan DLN-2 USB GPIO driver Octavian Purdila
3 siblings, 1 reply; 14+ messages in thread
From: Octavian Purdila @ 2014-10-15 14:48 UTC (permalink / raw)
To: gregkh, linus.walleij, gnurou, wsa, sameo, lee.jones
Cc: arnd, johan, daniel.baluta, laurentiu.palcu, linux-usb,
linux-kernel, linux-gpio, linux-i2c, Octavian Purdila
Some GPIO chips (e.g. the DLN2 USB adapter) have blocking get/set
operation but do not need a threaded irq handler.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
---
drivers/gpio/gpiolib.c | 2 +-
include/linux/gpio/driver.h | 3 +++
2 files changed, 4 insertions(+), 1 deletion(-)
diff --git a/drivers/gpio/gpiolib.c b/drivers/gpio/gpiolib.c
index 15cc0bb..3fa7e73 100644
--- a/drivers/gpio/gpiolib.c
+++ b/drivers/gpio/gpiolib.c
@@ -447,7 +447,7 @@ static int gpiochip_irq_map(struct irq_domain *d, unsigned int irq,
irq_set_lockdep_class(irq, &gpiochip_irq_lock_class);
irq_set_chip_and_handler(irq, chip->irqchip, chip->irq_handler);
/* Chips that can sleep need nested thread handlers */
- if (chip->can_sleep)
+ if (chip->can_sleep && !chip->irq_not_threaded)
irq_set_nested_thread(irq, 1);
#ifdef CONFIG_ARM
set_irq_flags(irq, IRQF_VALID);
diff --git a/include/linux/gpio/driver.h b/include/linux/gpio/driver.h
index e78a237..44161ac 100644
--- a/include/linux/gpio/driver.h
+++ b/include/linux/gpio/driver.h
@@ -56,6 +56,8 @@ struct seq_file;
* as the chip access may sleep when e.g. reading out the IRQ status
* registers.
* @exported: flags if the gpiochip is exported for use from sysfs. Private.
+ * @irq_not_threaded: flag must be set if @can_sleep is set but the
+ * IRQs don't need to be threaded
*
* A gpio_chip can help platforms abstract various sources of GPIOs so
* they can all be accessed through a common programing interface.
@@ -101,6 +103,7 @@ struct gpio_chip {
struct gpio_desc *desc;
const char *const *names;
bool can_sleep;
+ bool irq_not_threaded;
bool exported;
#ifdef CONFIG_GPIOLIB_IRQCHIP
--
1.9.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* Re: [PATCH v8 3/4] gpiolib: add irq_not_threaded flag to gpio_chip
2014-10-15 14:48 ` [PATCH v8 3/4] gpiolib: add irq_not_threaded flag to gpio_chip Octavian Purdila
@ 2014-10-20 5:08 ` Alexandre Courbot
[not found] ` <CAAVeFuJ4B37YgvTBctXqmtWJtg3b19PDt1EEZF5Rc6KVXZzUtw-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
0 siblings, 1 reply; 14+ messages in thread
From: Alexandre Courbot @ 2014-10-20 5:08 UTC (permalink / raw)
To: Octavian Purdila
Cc: Greg Kroah-Hartman, Linus Walleij, Wolfram Sang, Samuel Ortiz,
Lee Jones, Arnd Bergmann, Johan Hovold, daniel.baluta,
laurentiu.palcu, linux-usb@vger.kernel.org,
Linux Kernel Mailing List, linux-gpio@vger.kernel.org,
linux-i2c@vger.kernel.org
On Wed, Oct 15, 2014 at 11:48 PM, Octavian Purdila
<octavian.purdila@intel.com> wrote:
> Some GPIO chips (e.g. the DLN2 USB adapter) have blocking get/set
> operation but do not need a threaded irq handler.
Sorry if you already explained this (I have been a little bit late
with the GPIO reviews recently), but does this optimization bring a
significant benefit that justifies adding another field in struct
gpio_chip? If so it would be nice to have it in the commit message. If
not, do we need this at all?
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v8 4/4] gpio: add support for the Diolan DLN-2 USB GPIO driver
2014-10-15 14:48 [PATCH v8 0/4] mfd: add support for Diolan DLN-2 Octavian Purdila
` (2 preceding siblings ...)
2014-10-15 14:48 ` [PATCH v8 3/4] gpiolib: add irq_not_threaded flag to gpio_chip Octavian Purdila
@ 2014-10-15 14:48 ` Octavian Purdila
3 siblings, 0 replies; 14+ messages in thread
From: Octavian Purdila @ 2014-10-15 14:48 UTC (permalink / raw)
To: gregkh, linus.walleij, gnurou, wsa, sameo, lee.jones
Cc: arnd, johan, daniel.baluta, laurentiu.palcu, linux-usb,
linux-kernel, linux-gpio, linux-i2c, Octavian Purdila
From: Daniel Baluta <daniel.baluta@intel.com>
This patch adds GPIO and IRQ support for the Diolan DLN-2 GPIO module.
Information about the USB protocol interface can be found in the
Programmer's Reference Manual [1], see section 2.9 for the GPIO
module commands and responses.
[1] https://www.diolan.com/downloads/dln-api-manual.pdf
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
---
drivers/gpio/Kconfig | 12 +
drivers/gpio/Makefile | 1 +
drivers/gpio/gpio-dln2.c | 557 +++++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 570 insertions(+)
create mode 100644 drivers/gpio/gpio-dln2.c
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 9de1515..44ec206 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -897,4 +897,16 @@ config GPIO_VIPERBOARD
River Tech's viperboard.h for detailed meaning
of the module parameters.
+config GPIO_DLN2
+ tristate "Diolan DLN2 GPIO support"
+ depends on MFD_DLN2
+ select GPIOLIB_IRQCHIP
+
+ help
+ Select this option to enable GPIO driver for the Diolan DLN2
+ board.
+
+ This driver can also be built as a module. If so, the module
+ will be called gpio-dln2.
+
endif
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index 5d024e3..eaa97a0 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -26,6 +26,7 @@ obj-$(CONFIG_GPIO_CRYSTAL_COVE) += gpio-crystalcove.o
obj-$(CONFIG_GPIO_DA9052) += gpio-da9052.o
obj-$(CONFIG_GPIO_DA9055) += gpio-da9055.o
obj-$(CONFIG_GPIO_DAVINCI) += gpio-davinci.o
+obj-$(CONFIG_GPIO_DLN2) += gpio-dln2.o
obj-$(CONFIG_GPIO_DWAPB) += gpio-dwapb.o
obj-$(CONFIG_GPIO_EM) += gpio-em.o
obj-$(CONFIG_GPIO_EP93XX) += gpio-ep93xx.o
diff --git a/drivers/gpio/gpio-dln2.c b/drivers/gpio/gpio-dln2.c
new file mode 100644
index 0000000..70c25af
--- /dev/null
+++ b/drivers/gpio/gpio-dln2.c
@@ -0,0 +1,557 @@
+/*
+ * Driver for the Diolan DLN-2 USB-GPIO adapter
+ *
+ * Copyright (c) 2014 Intel Corporation
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation, version 2.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+#include <linux/irqdomain.h>
+#include <linux/irq.h>
+#include <linux/irqchip/chained_irq.h>
+#include <linux/gpio.h>
+#include <linux/gpio/driver.h>
+#include <linux/platform_device.h>
+#include <linux/mfd/dln2.h>
+
+#define DLN2_GPIO_ID 0x01
+
+#define DLN2_GPIO_GET_PIN_COUNT DLN2_CMD(0x01, DLN2_GPIO_ID)
+#define DLN2_GPIO_SET_DEBOUNCE DLN2_CMD(0x04, DLN2_GPIO_ID)
+#define DLN2_GPIO_GET_DEBOUNCE DLN2_CMD(0x05, DLN2_GPIO_ID)
+#define DLN2_GPIO_PORT_GET_VAL DLN2_CMD(0x06, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_GET_VAL DLN2_CMD(0x0B, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_SET_OUT_VAL DLN2_CMD(0x0C, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_GET_OUT_VAL DLN2_CMD(0x0D, DLN2_GPIO_ID)
+#define DLN2_GPIO_CONDITION_MET_EV DLN2_CMD(0x0F, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_ENABLE DLN2_CMD(0x10, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_DISABLE DLN2_CMD(0x11, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_SET_DIRECTION DLN2_CMD(0x13, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_GET_DIRECTION DLN2_CMD(0x14, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_SET_EVENT_CFG DLN2_CMD(0x1E, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_GET_EVENT_CFG DLN2_CMD(0x1F, DLN2_GPIO_ID)
+
+#define DLN2_GPIO_EVENT_NONE 0
+#define DLN2_GPIO_EVENT_CHANGE 1
+#define DLN2_GPIO_EVENT_LVL_HIGH 2
+#define DLN2_GPIO_EVENT_LVL_LOW 3
+#define DLN2_GPIO_EVENT_CHANGE_RISING 0x11
+#define DLN2_GPIO_EVENT_CHANGE_FALLING 0x21
+#define DLN2_GPIO_EVENT_MASK 0x0F
+
+#define DLN2_GPIO_MAX_PINS 32
+
+struct dln2_irq_work {
+ struct work_struct work;
+ struct dln2_gpio *dln2;
+ int pin;
+ int type;
+};
+
+struct dln2_gpio {
+ struct platform_device *pdev;
+ struct gpio_chip gpio;
+
+ /*
+ * Cache pin direction to save us one transfer, since the
+ * hardware has separate commands to read the in and out
+ * values.
+ */
+ DECLARE_BITMAP(output_enabled, DLN2_GPIO_MAX_PINS);
+
+ DECLARE_BITMAP(irqs_masked, DLN2_GPIO_MAX_PINS);
+ DECLARE_BITMAP(irqs_enabled, DLN2_GPIO_MAX_PINS);
+ DECLARE_BITMAP(irqs_pending, DLN2_GPIO_MAX_PINS);
+ struct dln2_irq_work *irq_work;
+};
+
+struct dln2_gpio_pin {
+ __le16 pin;
+};
+
+struct dln2_gpio_pin_val {
+ __le16 pin __packed;
+ u8 value;
+};
+
+static int dln2_gpio_get_pin_count(struct platform_device *pdev)
+{
+ int ret;
+ __le16 count;
+ int len = sizeof(count);
+
+ ret = dln2_transfer(pdev, DLN2_GPIO_GET_PIN_COUNT, NULL, 0, &count,
+ &len, NULL);
+ if (ret < 0)
+ return ret;
+ if (len < sizeof(count))
+ return -EPROTO;
+
+ return le16_to_cpu(count);
+}
+
+static int dln2_gpio_pin_cmd(struct dln2_gpio *dln2, int cmd, unsigned pin)
+{
+ struct dln2_gpio_pin req = {
+ .pin = cpu_to_le16(pin),
+ };
+
+ return dln2_transfer(dln2->pdev, cmd, &req, sizeof(req), NULL, NULL,
+ NULL);
+}
+
+static int dln2_gpio_pin_val(struct dln2_gpio *dln2, int cmd, unsigned int pin)
+{
+ int ret;
+ struct dln2_gpio_pin req = {
+ .pin = cpu_to_le16(pin),
+ };
+ struct dln2_gpio_pin_val rsp;
+ int len = sizeof(rsp);
+
+ ret = dln2_transfer(dln2->pdev, cmd, &req, sizeof(req), &rsp, &len,
+ NULL);
+ if (ret < 0)
+ return ret;
+ if (len < sizeof(rsp) || req.pin != rsp.pin)
+ return -EPROTO;
+
+ return rsp.value;
+}
+
+static int dln2_gpio_pin_get_in_val(struct dln2_gpio *dln2, unsigned int pin)
+{
+ int ret;
+
+ ret = dln2_gpio_pin_val(dln2, DLN2_GPIO_PIN_GET_VAL, pin);
+ if (ret < 0)
+ return ret;
+ return !!ret;
+}
+
+static int dln2_gpio_pin_get_out_val(struct dln2_gpio *dln2, unsigned int pin)
+{
+ int ret;
+
+ ret = dln2_gpio_pin_val(dln2, DLN2_GPIO_PIN_GET_OUT_VAL, pin);
+ if (ret < 0)
+ return ret;
+ return !!ret;
+}
+
+static void dln2_gpio_pin_set_out_val(struct dln2_gpio *dln2,
+ unsigned int pin, int value)
+{
+ struct dln2_gpio_pin_val req = {
+ .pin = cpu_to_le16(pin),
+ .value = cpu_to_le16(value),
+ };
+
+ dln2_transfer(dln2->pdev, DLN2_GPIO_PIN_SET_OUT_VAL, &req, sizeof(req),
+ NULL, NULL, NULL);
+}
+
+#define DLN2_GPIO_DIRECTION_IN 0
+#define DLN2_GPIO_DIRECTION_OUT 1
+
+static int dln2_gpio_request(struct gpio_chip *chip, unsigned offset)
+{
+ struct dln2_gpio *dln2 = container_of(chip, struct dln2_gpio, gpio);
+ struct dln2_gpio_pin req = {
+ .pin = cpu_to_le16(offset),
+ };
+ struct dln2_gpio_pin_val rsp;
+ int len = sizeof(rsp);
+ int ret;
+
+ ret = dln2_gpio_pin_cmd(dln2, DLN2_GPIO_PIN_ENABLE, offset);
+ if (ret < 0)
+ return ret;
+
+ /* cache the pin direction */
+ ret = dln2_transfer(dln2->pdev, DLN2_GPIO_PIN_GET_DIRECTION,
+ &req, sizeof(req), &rsp, &len, NULL);
+ if (ret < 0)
+ return ret;
+ if (len < sizeof(rsp) || req.pin != rsp.pin) {
+ ret = -EPROTO;
+ goto out_disable;
+ }
+
+ switch (rsp.value) {
+ case DLN2_GPIO_DIRECTION_IN:
+ clear_bit(offset, dln2->output_enabled);
+ return 0;
+ case DLN2_GPIO_DIRECTION_OUT:
+ set_bit(offset, dln2->output_enabled);
+ return 0;
+ default:
+ ret = -EPROTO;
+ goto out_disable;
+ }
+
+out_disable:
+ dln2_gpio_pin_cmd(dln2, DLN2_GPIO_PIN_DISABLE, offset);
+ return ret;
+}
+
+static void dln2_gpio_free(struct gpio_chip *chip, unsigned offset)
+{
+ struct dln2_gpio *dln2 = container_of(chip, struct dln2_gpio, gpio);
+
+ dln2_gpio_pin_cmd(dln2, DLN2_GPIO_PIN_DISABLE, offset);
+}
+
+static int dln2_gpio_get_direction(struct gpio_chip *chip, unsigned offset)
+{
+ struct dln2_gpio *dln2 = container_of(chip, struct dln2_gpio, gpio);
+
+ if (test_bit(offset, dln2->output_enabled))
+ return GPIOF_DIR_OUT;
+
+ return GPIOF_DIR_IN;
+}
+
+static int dln2_gpio_get(struct gpio_chip *chip, unsigned int offset)
+{
+ struct dln2_gpio *dln2 = container_of(chip, struct dln2_gpio, gpio);
+ int dir;
+
+ dir = dln2_gpio_get_direction(chip, offset);
+ if (dir < 0)
+ return dir;
+
+ if (dir == GPIOF_DIR_IN)
+ return dln2_gpio_pin_get_in_val(dln2, offset);
+
+ return dln2_gpio_pin_get_out_val(dln2, offset);
+}
+
+static void dln2_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
+{
+ struct dln2_gpio *dln2 = container_of(chip, struct dln2_gpio, gpio);
+
+ dln2_gpio_pin_set_out_val(dln2, offset, value);
+}
+
+static int dln2_gpio_set_direction(struct gpio_chip *chip, unsigned offset,
+ unsigned dir)
+{
+ struct dln2_gpio *dln2 = container_of(chip, struct dln2_gpio, gpio);
+ struct dln2_gpio_pin_val req = {
+ .pin = cpu_to_le16(offset),
+ .value = cpu_to_le16(dir),
+ };
+ int ret;
+
+ ret = dln2_transfer(dln2->pdev, DLN2_GPIO_PIN_SET_DIRECTION,
+ &req, sizeof(req), NULL, NULL, NULL);
+ if (ret < 0)
+ return ret;
+
+ if (dir == DLN2_GPIO_DIRECTION_OUT)
+ set_bit(offset, dln2->output_enabled);
+ else
+ clear_bit(offset, dln2->output_enabled);
+
+ return ret;
+}
+
+static int dln2_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
+{
+ return dln2_gpio_set_direction(chip, offset, DLN2_GPIO_DIRECTION_IN);
+}
+
+static int dln2_gpio_direction_output(struct gpio_chip *chip, unsigned offset,
+ int value)
+{
+ return dln2_gpio_set_direction(chip, offset, DLN2_GPIO_DIRECTION_OUT);
+}
+
+static int dln2_gpio_set_debounce(struct gpio_chip *chip, unsigned offset,
+ unsigned debounce)
+{
+ struct dln2_gpio *dln2 = container_of(chip, struct dln2_gpio, gpio);
+ __le32 duration = cpu_to_le32(debounce);
+
+ return dln2_transfer(dln2->pdev, DLN2_GPIO_SET_DEBOUNCE,
+ &duration, sizeof(duration), NULL, NULL, NULL);
+}
+
+static int dln2_gpio_set_event_cfg(struct dln2_gpio *dln2, unsigned pin,
+ unsigned type, unsigned period)
+{
+ struct {
+ __le16 pin;
+ u8 type;
+ __le16 period;
+ } __packed req = {
+ .pin = cpu_to_le16(pin),
+ .type = type,
+ .period = cpu_to_le16(period),
+ };
+
+ return dln2_transfer(dln2->pdev, DLN2_GPIO_PIN_SET_EVENT_CFG,
+ &req, sizeof(req), NULL, NULL, NULL);
+}
+
+static void dln2_irq_work(struct work_struct *w)
+{
+ struct dln2_irq_work *iw = container_of(w, struct dln2_irq_work, work);
+ struct dln2_gpio *dln2 = iw->dln2;
+ u8 type = iw->type & DLN2_GPIO_EVENT_MASK;
+
+ if (test_bit(iw->pin, dln2->irqs_enabled))
+ dln2_gpio_set_event_cfg(dln2, iw->pin, type, 0);
+ else
+ dln2_gpio_set_event_cfg(dln2, iw->pin, DLN2_GPIO_EVENT_NONE, 0);
+}
+
+static void dln2_irq_enable(struct irq_data *irqd)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+ struct dln2_gpio *dln2 = container_of(gc, struct dln2_gpio, gpio);
+ int pin = irqd_to_hwirq(irqd);
+
+ set_bit(pin, dln2->irqs_enabled);
+ schedule_work(&dln2->irq_work[pin].work);
+}
+
+static void dln2_irq_disable(struct irq_data *irqd)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+ struct dln2_gpio *dln2 = container_of(gc, struct dln2_gpio, gpio);
+ int pin = irqd_to_hwirq(irqd);
+
+ clear_bit(pin, dln2->irqs_enabled);
+ schedule_work(&dln2->irq_work[pin].work);
+}
+
+static void dln2_irq_mask(struct irq_data *irqd)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+ struct dln2_gpio *dln2 = container_of(gc, struct dln2_gpio, gpio);
+ int pin = irqd_to_hwirq(irqd);
+
+ set_bit(pin, dln2->irqs_masked);
+}
+
+static void dln2_irq_unmask(struct irq_data *irqd)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+ struct dln2_gpio *dln2 = container_of(gc, struct dln2_gpio, gpio);
+ struct device *dev = dln2->gpio.dev;
+ int pin = irqd_to_hwirq(irqd);
+
+ if (test_and_clear_bit(pin, dln2->irqs_pending)) {
+ int irq;
+
+ irq = irq_find_mapping(dln2->gpio.irqdomain, pin);
+ if (!irq) {
+ dev_err(dev, "pin %d not mapped to IRQ\n", pin);
+ return;
+ }
+
+ generic_handle_irq(irq);
+ }
+}
+
+static int dln2_irq_set_type(struct irq_data *irqd, unsigned type)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+ struct dln2_gpio *dln2 = container_of(gc, struct dln2_gpio, gpio);
+ int pin = irqd_to_hwirq(irqd);
+
+ switch (type) {
+ case IRQ_TYPE_LEVEL_HIGH:
+ dln2->irq_work[pin].type = DLN2_GPIO_EVENT_LVL_HIGH;
+ break;
+ case IRQ_TYPE_LEVEL_LOW:
+ dln2->irq_work[pin].type = DLN2_GPIO_EVENT_LVL_LOW;
+ break;
+ case IRQ_TYPE_EDGE_BOTH:
+ dln2->irq_work[pin].type = DLN2_GPIO_EVENT_CHANGE;
+ break;
+ case IRQ_TYPE_EDGE_RISING:
+ dln2->irq_work[pin].type = DLN2_GPIO_EVENT_CHANGE_RISING;
+ break;
+ case IRQ_TYPE_EDGE_FALLING:
+ dln2->irq_work[pin].type = DLN2_GPIO_EVENT_CHANGE_FALLING;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static struct irq_chip dln2_gpio_irqchip = {
+ .name = "dln2-irq",
+ .irq_enable = dln2_irq_enable,
+ .irq_disable = dln2_irq_disable,
+ .irq_mask = dln2_irq_mask,
+ .irq_unmask = dln2_irq_unmask,
+ .irq_set_type = dln2_irq_set_type,
+};
+
+static void dln2_gpio_event(struct platform_device *pdev, u16 echo,
+ const void *data, int len)
+{
+ int pin, irq;
+ const struct {
+ __le16 count;
+ __u8 type;
+ __le16 pin;
+ __u8 value;
+ } __packed *event = data;
+ struct dln2_gpio *dln2 = platform_get_drvdata(pdev);
+
+ if (len < sizeof(*event)) {
+ dev_err(dln2->gpio.dev, "short event message\n");
+ return;
+ }
+
+ pin = le16_to_cpu(event->pin);
+ if (pin >= dln2->gpio.ngpio) {
+ dev_err(dln2->gpio.dev, "out of bounds pin %d\n", pin);
+ return;
+ }
+
+ irq = irq_find_mapping(dln2->gpio.irqdomain, pin);
+ if (!irq) {
+ dev_err(dln2->gpio.dev, "pin %d not mapped to IRQ\n", pin);
+ return;
+ }
+
+ if (!test_bit(pin, dln2->irqs_enabled))
+ return;
+ if (test_bit(pin, dln2->irqs_masked)) {
+ set_bit(pin, dln2->irqs_pending);
+ return;
+ }
+
+ switch (dln2->irq_work[pin].type) {
+ case DLN2_GPIO_EVENT_CHANGE_RISING:
+ if (event->value)
+ generic_handle_irq(irq);
+ break;
+ case DLN2_GPIO_EVENT_CHANGE_FALLING:
+ if (!event->value)
+ generic_handle_irq(irq);
+ break;
+ default:
+ generic_handle_irq(irq);
+ }
+}
+
+static int dln2_gpio_probe(struct platform_device *pdev)
+{
+ struct dln2_gpio *dln2;
+ struct device *dev = &pdev->dev;
+ int pins;
+ int i, ret;
+
+ pins = dln2_gpio_get_pin_count(pdev);
+ if (pins < 0) {
+ dev_err(dev, "failed to get pin count: %d\n", pins);
+ return pins;
+ }
+ if (pins > DLN2_GPIO_MAX_PINS) {
+ pins = DLN2_GPIO_MAX_PINS;
+ dev_warn(dev, "clamping pins to %d\n", DLN2_GPIO_MAX_PINS);
+ }
+
+ dln2 = devm_kzalloc(&pdev->dev, sizeof(*dln2), GFP_KERNEL);
+ if (!dln2)
+ return -ENOMEM;
+
+ dln2->irq_work = devm_kcalloc(&pdev->dev, pins,
+ sizeof(struct dln2_irq_work), GFP_KERNEL);
+ if (!dln2->irq_work)
+ return -ENOMEM;
+ for (i = 0; i < pins; i++) {
+ INIT_WORK(&dln2->irq_work[i].work, dln2_irq_work);
+ dln2->irq_work[i].pin = i;
+ dln2->irq_work[i].dln2 = dln2;
+ }
+
+ dln2->pdev = pdev;
+
+ dln2->gpio.label = "dln2";
+ dln2->gpio.dev = dev;
+ dln2->gpio.owner = THIS_MODULE;
+ dln2->gpio.base = -1;
+ dln2->gpio.ngpio = pins;
+ dln2->gpio.exported = true;
+ dln2->gpio.can_sleep = true;
+ dln2->gpio.irq_not_threaded = true;
+ dln2->gpio.set = dln2_gpio_set;
+ dln2->gpio.get = dln2_gpio_get;
+ dln2->gpio.request = dln2_gpio_request;
+ dln2->gpio.free = dln2_gpio_free;
+ dln2->gpio.get_direction = dln2_gpio_get_direction;
+ dln2->gpio.direction_input = dln2_gpio_direction_input;
+ dln2->gpio.direction_output = dln2_gpio_direction_output;
+ dln2->gpio.set_debounce = dln2_gpio_set_debounce;
+
+ platform_set_drvdata(pdev, dln2);
+
+ ret = gpiochip_add(&dln2->gpio);
+ if (ret < 0) {
+ dev_err(dev, "failed to add gpio chip: %d\n", ret);
+ goto out;
+ }
+
+ ret = gpiochip_irqchip_add(&dln2->gpio, &dln2_gpio_irqchip, 0,
+ handle_simple_irq, IRQ_TYPE_NONE);
+ if (ret < 0) {
+ dev_err(dev, "failed to add irq chip: %d\n", ret);
+ goto out_gpiochip_remove;
+ }
+
+ ret = dln2_register_event_cb(pdev, DLN2_GPIO_CONDITION_MET_EV,
+ dln2_gpio_event);
+ if (ret) {
+ dev_err(dev, "failed to register event cb: %d\n", ret);
+ goto out_gpiochip_remove;
+ }
+
+ return 0;
+
+out_gpiochip_remove:
+ gpiochip_remove(&dln2->gpio);
+out:
+ return ret;
+}
+
+static int dln2_gpio_remove(struct platform_device *pdev)
+{
+ struct dln2_gpio *dln2 = platform_get_drvdata(pdev);
+ int i;
+
+ dln2_unregister_event_cb(pdev, DLN2_GPIO_CONDITION_MET_EV);
+ for (i = 0; i < dln2->gpio.ngpio; i++)
+ flush_work(&dln2->irq_work[i].work);
+ gpiochip_remove(&dln2->gpio);
+
+ return 0;
+}
+
+static struct platform_driver dln2_gpio_driver = {
+ .driver.name = "dln2-gpio",
+ .probe = dln2_gpio_probe,
+ .remove = dln2_gpio_remove,
+};
+
+module_platform_driver(dln2_gpio_driver);
+
+MODULE_AUTHOR("Daniel Baluta <daniel.baluta@intel.com");
+MODULE_DESCRIPTION("Driver for the Diolan DLN2 GPIO interface");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:dln2-gpio");
--
1.9.1
^ permalink raw reply related [flat|nested] 14+ messages in thread