[PATCH v11 0/3] add support for Diolan DLN-2

[PATCH v11 0/3] add support for Diolan DLN-2

[Octavian Purdila]

This patch series adds support for Diolan USB-I2C/GPIO Master Adapter
DLN-2. Details about device can be found here:

https://www.diolan.com/i2c/i2c_interface.html.

This patch series has been rebased against the for-mfd-next branch of
the MFD tree.

Changes since v10:

 * MFD: fix a couple of typos

Changes since v9:

 * MFD: use decimal serial no, break the run callback loop (there can
   be only one entry per id), move up the declaration of a couple of
   variables, remove a couple of redundant __packed attributes, fix a
   typo and cleanup an error message, use unsigned long instead of int
   for timeout

 * I2C: none

 * GPIO: drop a couple of cpu_to_le16() due to receiving data type
   being u8



Daniel Baluta (1):
  gpio: add support for the Diolan DLN-2 USB GPIO driver

Laurentiu Palcu (1):
  i2c: add support for Diolan DLN-2 USB-I2C adapter

Octavian Purdila (1):
  mfd: add support for Diolan DLN-2 devices

 drivers/gpio/Kconfig          |  12 +
 drivers/gpio/Makefile         |   1 +
 drivers/gpio/gpio-dln2.c      | 553 ++++++++++++++++++++++++++++++
 drivers/i2c/busses/Kconfig    |  10 +
 drivers/i2c/busses/Makefile   |   1 +
 drivers/i2c/busses/i2c-dln2.c | 267 +++++++++++++++
 drivers/mfd/Kconfig           |  11 +
 drivers/mfd/Makefile          |   1 +
 drivers/mfd/dln2.c            | 763 ++++++++++++++++++++++++++++++++++++++++++
 include/linux/mfd/dln2.h      | 103 ++++++
 10 files changed, 1722 insertions(+)
 create mode 100644 drivers/gpio/gpio-dln2.c
 create mode 100644 drivers/i2c/busses/i2c-dln2.c
 create mode 100644 drivers/mfd/dln2.c
 create mode 100644 include/linux/mfd/dln2.h

-- 
1.9.1

[PATCH v11 1/3] mfd: add support for Diolan DLN-2 devices

[Octavian Purdila]

This patch implements the USB part of the Diolan USB-I2C/SPI/GPIO
Master Adapter DLN-2. Details about the device can be found here:

https://www.diolan.com/i2c/i2c_interface.html.

Information about the USB protocol can be found in the Programmer's
Reference Manual [1], see section 1.7.

Because the hardware has a single transmit endpoint and a single
receive endpoint the communication between the various DLN2 drivers
and the hardware will be muxed/demuxed by this driver.

Each DLN2 module will be identified by the handle field within the DLN2
message header. If a DLN2 module issues multiple commands in parallel
they will be identified by the echo counter field in the message header.

The DLN2 modules can use the dln2_transfer() function to issue a
command and wait for its response. They can also register a callback
that is going to be called when a specific event id is generated by
the device (e.g. GPIO interrupts). The device uses handle 0 for
sending events.

[1] https://www.diolan.com/downloads/dln-api-manual.pdf

Signed-off-by: Octavian Purdila <octavian.purdila-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
Reviewed-by: Johan Hovold <johan-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
---
 drivers/mfd/Kconfig      |  11 +
 drivers/mfd/Makefile     |   1 +
 drivers/mfd/dln2.c       | 763 +++++++++++++++++++++++++++++++++++++++++++++++
 include/linux/mfd/dln2.h | 103 +++++++
 4 files changed, 878 insertions(+)
 create mode 100644 drivers/mfd/dln2.c
 create mode 100644 include/linux/mfd/dln2.h

diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index cbdb109..32d7cab 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -189,6 +189,17 @@ config MFD_DA9063
 	  Additional drivers must be enabled in order to use the functionality
 	  of the device.
 
+config MFD_DLN2
+	tristate "Diolan DLN2 support"
+	select MFD_CORE
+	depends on USB
+	help
+
+	  This adds support for Diolan USB-I2C/SPI/GPIO Master Adapter
+	  DLN-2. Additional drivers such as I2C_DLN2, GPIO_DLN2,
+	  etc. must be enabled in order to use the functionality of
+	  the device.
+
 config MFD_MC13XXX
 	tristate
 	depends on (SPI_MASTER || I2C)
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 8e679d6..53467e2 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -175,6 +175,7 @@ obj-$(CONFIG_MFD_STW481X)	+= stw481x.o
 obj-$(CONFIG_MFD_IPAQ_MICRO)	+= ipaq-micro.o
 obj-$(CONFIG_MFD_MENF21BMC)	+= menf21bmc.o
 obj-$(CONFIG_MFD_HI6421_PMIC)	+= hi6421-pmic-core.o
+obj-$(CONFIG_MFD_DLN2)		+= dln2.o
 
 intel-soc-pmic-objs		:= intel_soc_pmic_core.o intel_soc_pmic_crc.o
 obj-$(CONFIG_INTEL_SOC_PMIC)	+= intel-soc-pmic.o
diff --git a/drivers/mfd/dln2.c b/drivers/mfd/dln2.c
new file mode 100644
index 0000000..9765a17
--- /dev/null
+++ b/drivers/mfd/dln2.c
@@ -0,0 +1,763 @@
+/*
+ * Driver for the Diolan DLN-2 USB adapter
+ *
+ * Copyright (c) 2014 Intel Corporation
+ *
+ * Derived from:
+ *  i2c-diolan-u2c.c
+ *  Copyright (c) 2010-2011 Ericsson AB
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation, version 2.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/slab.h>
+#include <linux/usb.h>
+#include <linux/i2c.h>
+#include <linux/mutex.h>
+#include <linux/platform_device.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/dln2.h>
+#include <linux/rculist.h>
+
+struct dln2_header {
+	__le16 size;
+	__le16 id;
+	__le16 echo;
+	__le16 handle;
+};
+
+struct dln2_response {
+	struct dln2_header hdr;
+	__le16 result;
+};
+
+#define DLN2_GENERIC_MODULE_ID		0x00
+#define DLN2_GENERIC_CMD(cmd)		DLN2_CMD(cmd, DLN2_GENERIC_MODULE_ID)
+#define CMD_GET_DEVICE_VER		DLN2_GENERIC_CMD(0x30)
+#define CMD_GET_DEVICE_SN		DLN2_GENERIC_CMD(0x31)
+
+#define DLN2_HW_ID			0x200
+#define DLN2_USB_TIMEOUT		200	/* in ms */
+#define DLN2_MAX_RX_SLOTS		16
+#define DLN2_MAX_URBS			16
+#define DLN2_RX_BUF_SIZE		512
+
+enum dln2_handle {
+	DLN2_HANDLE_EVENT = 0,		/* don't change, hardware defined */
+	DLN2_HANDLE_CTRL,
+	DLN2_HANDLE_GPIO,
+	DLN2_HANDLE_I2C,
+	DLN2_HANDLES
+};
+
+/*
+ * Receive context used between the receive demultiplexer and the transfer
+ * routine. While sending a request the transfer routine will look for a free
+ * receive context and use it to wait for a response and to receive the URB and
+ * thus the response data.
+ */
+struct dln2_rx_context {
+	/* completion used to wait for a response */
+	struct completion done;
+
+	/* if non-NULL the URB contains the response */
+	struct urb *urb;
+
+	/* if true then this context is used to wait for a response */
+	bool in_use;
+};
+
+/*
+ * Receive contexts for a particular DLN2 module (i2c, gpio, etc.). We use the
+ * handle header field to identify the module in dln2_dev.mod_rx_slots and then
+ * the echo header field to index the slots field and find the receive context
+ * for a particular request.
+ */
+struct dln2_mod_rx_slots {
+	/* RX slots bitmap */
+	DECLARE_BITMAP(bmap, DLN2_MAX_RX_SLOTS);
+
+	/* used to wait for a free RX slot */
+	wait_queue_head_t wq;
+
+	/* used to wait for an RX operation to complete */
+	struct dln2_rx_context slots[DLN2_MAX_RX_SLOTS];
+
+	/* avoid races between alloc/free_rx_slot and dln2_rx_transfer */
+	spinlock_t lock;
+};
+
+struct dln2_dev {
+	struct usb_device *usb_dev;
+	struct usb_interface *interface;
+	u8 ep_in;
+	u8 ep_out;
+
+	struct urb *rx_urb[DLN2_MAX_URBS];
+	void *rx_buf[DLN2_MAX_URBS];
+
+	struct dln2_mod_rx_slots mod_rx_slots[DLN2_HANDLES];
+
+	struct list_head event_cb_list;
+	spinlock_t event_cb_lock;
+
+	bool disconnect;
+	int active_transfers;
+	wait_queue_head_t disconnect_wq;
+	spinlock_t disconnect_lock;
+};
+
+struct dln2_event_cb_entry {
+	struct list_head list;
+	u16 id;
+	struct platform_device *pdev;
+	dln2_event_cb_t callback;
+};
+
+int dln2_register_event_cb(struct platform_device *pdev, u16 id,
+			   dln2_event_cb_t event_cb)
+{
+	struct dln2_dev *dln2 = dev_get_drvdata(pdev->dev.parent);
+	struct dln2_event_cb_entry *i, *entry;
+	unsigned long flags;
+	int ret = 0;
+
+	entry = kzalloc(sizeof(*entry), GFP_KERNEL);
+	if (!entry)
+		return -ENOMEM;
+
+	entry->id = id;
+	entry->callback = event_cb;
+	entry->pdev = pdev;
+
+	spin_lock_irqsave(&dln2->event_cb_lock, flags);
+
+	list_for_each_entry(i, &dln2->event_cb_list, list) {
+		if (i->id == id) {
+			ret = -EBUSY;
+			break;
+		}
+	}
+
+	if (!ret)
+		list_add_rcu(&entry->list, &dln2->event_cb_list);
+
+	spin_unlock_irqrestore(&dln2->event_cb_lock, flags);
+
+	if (ret)
+		kfree(entry);
+
+	return ret;
+}
+EXPORT_SYMBOL(dln2_register_event_cb);
+
+void dln2_unregister_event_cb(struct platform_device *pdev, u16 id)
+{
+	struct dln2_dev *dln2 = dev_get_drvdata(pdev->dev.parent);
+	struct dln2_event_cb_entry *i;
+	unsigned long flags;
+	bool found = false;
+
+	spin_lock_irqsave(&dln2->event_cb_lock, flags);
+
+	list_for_each_entry(i, &dln2->event_cb_list, list) {
+		if (i->id == id) {
+			list_del_rcu(&i->list);
+			found = true;
+			break;
+		}
+	}
+
+	spin_unlock_irqrestore(&dln2->event_cb_lock, flags);
+
+	if (found) {
+		synchronize_rcu();
+		kfree(i);
+	}
+}
+EXPORT_SYMBOL(dln2_unregister_event_cb);
+
+/*
+ * Returns true if a valid transfer slot is found. In this case the URB must not
+ * be resubmitted immediately in dln2_rx as we need the data when dln2_transfer
+ * is woke up. It will be resubmitted there.
+ */
+static bool dln2_transfer_complete(struct dln2_dev *dln2, struct urb *urb,
+				   u16 handle, u16 rx_slot)
+{
+	struct device *dev = &dln2->interface->dev;
+	struct dln2_mod_rx_slots *rxs = &dln2->mod_rx_slots[handle];
+	struct dln2_rx_context *rxc;
+	bool valid_slot = false;
+
+	rxc = &rxs->slots[rx_slot];
+
+	/*
+	 * No need to disable interrupts as this lock is not taken in interrupt
+	 * context elsewhere in this driver. This function (or its callers) are
+	 * also not exported to other modules.
+	 */
+	spin_lock(&rxs->lock);
+	if (rxc->in_use && !rxc->urb) {
+		rxc->urb = urb;
+		complete(&rxc->done);
+		valid_slot = true;
+	}
+	spin_unlock(&rxs->lock);
+
+	if (!valid_slot)
+		dev_warn(dev, "bad/late response %d/%d\n", handle, rx_slot);
+
+	return valid_slot;
+}
+
+static void dln2_run_event_callbacks(struct dln2_dev *dln2, u16 id, u16 echo,
+				     void *data, int len)
+{
+	struct dln2_event_cb_entry *i;
+
+	rcu_read_lock();
+
+	list_for_each_entry_rcu(i, &dln2->event_cb_list, list) {
+		if (i->id == id) {
+			i->callback(i->pdev, echo, data, len);
+			break;
+		}
+	}
+
+	rcu_read_unlock();
+}
+
+static void dln2_rx(struct urb *urb)
+{
+	struct dln2_dev *dln2 = urb->context;
+	struct dln2_header *hdr = urb->transfer_buffer;
+	struct device *dev = &dln2->interface->dev;
+	u16 id, echo, handle, size;
+	u8 *data;
+	int len;
+	int err;
+
+	switch (urb->status) {
+	case 0:
+		/* success */
+		break;
+	case -ECONNRESET:
+	case -ENOENT:
+	case -ESHUTDOWN:
+	case -EPIPE:
+		/* this urb is terminated, clean up */
+		dev_dbg(dev, "urb shutting down with status %d\n", urb->status);
+		return;
+	default:
+		dev_dbg(dev, "nonzero urb status received %d\n", urb->status);
+		goto out;
+	}
+
+	if (urb->actual_length < sizeof(struct dln2_header)) {
+		dev_err(dev, "short response: %d\n", urb->actual_length);
+		goto out;
+	}
+
+	handle = le16_to_cpu(hdr->handle);
+	id = le16_to_cpu(hdr->id);
+	echo = le16_to_cpu(hdr->echo);
+	size = le16_to_cpu(hdr->size);
+
+	if (size != urb->actual_length) {
+		dev_err(dev, "size mismatch: handle %x cmd %x echo %x size %d actual %d\n",
+			handle, id, echo, size, urb->actual_length);
+		goto out;
+	}
+
+	if (handle >= DLN2_HANDLES) {
+		dev_warn(dev, "invalid handle %d\n", handle);
+		goto out;
+	}
+
+	data = urb->transfer_buffer + sizeof(struct dln2_header);
+	len = urb->actual_length - sizeof(struct dln2_header);
+
+	if (handle == DLN2_HANDLE_EVENT) {
+		dln2_run_event_callbacks(dln2, id, echo, data, len);
+	} else {
+		/* URB will be re-submitted in _dln2_transfer (free_rx_slot) */
+		if (dln2_transfer_complete(dln2, urb, handle, echo))
+			return;
+	}
+
+out:
+	err = usb_submit_urb(urb, GFP_ATOMIC);
+	if (err < 0)
+		dev_err(dev, "failed to resubmit RX URB: %d\n", err);
+}
+
+static void *dln2_prep_buf(u16 handle, u16 cmd, u16 echo, const void *obuf,
+			   int *obuf_len, gfp_t gfp)
+{
+	int len;
+	void *buf;
+	struct dln2_header *hdr;
+
+	len = *obuf_len + sizeof(*hdr);
+	buf = kmalloc(len, gfp);
+	if (!buf)
+		return NULL;
+
+	hdr = (struct dln2_header *)buf;
+	hdr->id = cpu_to_le16(cmd);
+	hdr->size = cpu_to_le16(len);
+	hdr->echo = cpu_to_le16(echo);
+	hdr->handle = cpu_to_le16(handle);
+
+	memcpy(buf + sizeof(*hdr), obuf, *obuf_len);
+
+	*obuf_len = len;
+
+	return buf;
+}
+
+static int dln2_send_wait(struct dln2_dev *dln2, u16 handle, u16 cmd, u16 echo,
+			  const void *obuf, int obuf_len)
+{
+	int ret = 0;
+	int len = obuf_len;
+	void *buf;
+	int actual;
+
+	buf = dln2_prep_buf(handle, cmd, echo, obuf, &len, GFP_KERNEL);
+	if (!buf)
+		return -ENOMEM;
+
+	ret = usb_bulk_msg(dln2->usb_dev,
+			   usb_sndbulkpipe(dln2->usb_dev, dln2->ep_out),
+			   buf, len, &actual, DLN2_USB_TIMEOUT);
+
+	kfree(buf);
+
+	return ret;
+}
+
+static bool find_free_slot(struct dln2_dev *dln2, u16 handle, int *slot)
+{
+	struct dln2_mod_rx_slots *rxs;
+	unsigned long flags;
+
+	if (dln2->disconnect) {
+		*slot = -ENODEV;
+		return true;
+	}
+
+	rxs = &dln2->mod_rx_slots[handle];
+
+	spin_lock_irqsave(&rxs->lock, flags);
+
+	*slot = find_first_zero_bit(rxs->bmap, DLN2_MAX_RX_SLOTS);
+
+	if (*slot < DLN2_MAX_RX_SLOTS) {
+		struct dln2_rx_context *rxc = &rxs->slots[*slot];
+
+		set_bit(*slot, rxs->bmap);
+		rxc->in_use = true;
+	}
+
+	spin_unlock_irqrestore(&rxs->lock, flags);
+
+	return *slot < DLN2_MAX_RX_SLOTS;
+}
+
+static int alloc_rx_slot(struct dln2_dev *dln2, u16 handle)
+{
+	int ret;
+	int slot;
+
+	/*
+	 * No need to timeout here, the wait is bounded by the timeout in
+	 * _dln2_transfer.
+	 */
+	ret = wait_event_interruptible(dln2->mod_rx_slots[handle].wq,
+				       find_free_slot(dln2, handle, &slot));
+	if (ret < 0)
+		return ret;
+
+	return slot;
+}
+
+static void free_rx_slot(struct dln2_dev *dln2, u16 handle, int slot)
+{
+	struct dln2_mod_rx_slots *rxs;
+	struct urb *urb = NULL;
+	unsigned long flags;
+	struct dln2_rx_context *rxc;
+
+	rxs = &dln2->mod_rx_slots[handle];
+
+	spin_lock_irqsave(&rxs->lock, flags);
+
+	clear_bit(slot, rxs->bmap);
+
+	rxc = &rxs->slots[slot];
+	rxc->in_use = false;
+	urb = rxc->urb;
+	rxc->urb = NULL;
+	reinit_completion(&rxc->done);
+
+	spin_unlock_irqrestore(&rxs->lock, flags);
+
+	if (urb) {
+		int err;
+		struct device *dev = &dln2->interface->dev;
+
+		err = usb_submit_urb(urb, GFP_KERNEL);
+		if (err < 0)
+			dev_err(dev, "failed to resubmit RX URB: %d\n", err);
+	}
+
+	wake_up_interruptible(&rxs->wq);
+}
+
+static int _dln2_transfer(struct dln2_dev *dln2, u16 handle, u16 cmd,
+			  const void *obuf, unsigned obuf_len,
+			  void *ibuf, unsigned *ibuf_len)
+{
+	int ret = 0;
+	int rx_slot;
+	struct dln2_response *rsp;
+	struct dln2_rx_context *rxc;
+	struct device *dev = &dln2->interface->dev;
+	const unsigned long timeout = DLN2_USB_TIMEOUT * HZ / 1000;
+	struct dln2_mod_rx_slots *rxs = &dln2->mod_rx_slots[handle];
+
+	spin_lock(&dln2->disconnect_lock);
+	if (!dln2->disconnect)
+		dln2->active_transfers++;
+	else
+		ret = -ENODEV;
+	spin_unlock(&dln2->disconnect_lock);
+
+	if (ret)
+		return ret;
+
+	rx_slot = alloc_rx_slot(dln2, handle);
+	if (rx_slot < 0) {
+		ret = rx_slot;
+		goto out_decr;
+	}
+
+	ret = dln2_send_wait(dln2, handle, cmd, rx_slot, obuf, obuf_len);
+	if (ret < 0) {
+		dev_err(dev, "USB write failed: %d\n", ret);
+		goto out_free_rx_slot;
+	}
+
+	rxc = &rxs->slots[rx_slot];
+
+	ret = wait_for_completion_interruptible_timeout(&rxc->done, timeout);
+	if (ret <= 0) {
+		if (!ret)
+			ret = -ETIMEDOUT;
+		goto out_free_rx_slot;
+	}
+
+	if (dln2->disconnect) {
+		ret = -ENODEV;
+		goto out_free_rx_slot;
+	}
+
+	/* if we got here we know that the response header has been checked */
+	rsp = rxc->urb->transfer_buffer;
+
+	if (rsp->hdr.size < sizeof(*rsp)) {
+		ret = -EPROTO;
+		goto out_free_rx_slot;
+	}
+
+	if (le16_to_cpu(rsp->result) > 0x80) {
+		dev_dbg(dev, "%d received response with error %d\n",
+			handle, le16_to_cpu(rsp->result));
+		ret = -EREMOTEIO;
+		goto out_free_rx_slot;
+	}
+
+	if (!ibuf) {
+		ret = 0;
+		goto out_free_rx_slot;
+	}
+
+	if (*ibuf_len > rsp->hdr.size - sizeof(*rsp))
+		*ibuf_len = rsp->hdr.size - sizeof(*rsp);
+
+	memcpy(ibuf, rsp + 1, *ibuf_len);
+
+out_free_rx_slot:
+	free_rx_slot(dln2, handle, rx_slot);
+out_decr:
+	spin_lock(&dln2->disconnect_lock);
+	dln2->active_transfers--;
+	spin_unlock(&dln2->disconnect_lock);
+	if (dln2->disconnect)
+		wake_up(&dln2->disconnect_wq);
+
+	return ret;
+}
+
+int dln2_transfer(struct platform_device *pdev, u16 cmd,
+		  const void *obuf, unsigned obuf_len,
+		  void *ibuf, unsigned *ibuf_len)
+{
+	struct dln2_platform_data *dln2_pdata;
+	struct dln2_dev *dln2;
+	u16 handle;
+
+	dln2 = dev_get_drvdata(pdev->dev.parent);
+	dln2_pdata = dev_get_platdata(&pdev->dev);
+	handle = dln2_pdata->handle;
+
+	return _dln2_transfer(dln2, handle, cmd, obuf, obuf_len, ibuf,
+			      ibuf_len);
+}
+EXPORT_SYMBOL(dln2_transfer);
+
+static int dln2_check_hw(struct dln2_dev *dln2)
+{
+	int ret;
+	__le32 hw_type;
+	int len = sizeof(hw_type);
+
+	ret = _dln2_transfer(dln2, DLN2_HANDLE_CTRL, CMD_GET_DEVICE_VER,
+			     NULL, 0, &hw_type, &len);
+	if (ret < 0)
+		return ret;
+	if (len < sizeof(hw_type))
+		return -EREMOTEIO;
+
+	if (le32_to_cpu(hw_type) != DLN2_HW_ID) {
+		dev_err(&dln2->interface->dev, "Device ID 0x%x not supported\n",
+			le32_to_cpu(hw_type));
+		return -ENODEV;
+	}
+
+	return 0;
+}
+
+static int dln2_print_serialno(struct dln2_dev *dln2)
+{
+	int ret;
+	__le32 serial_no;
+	int len = sizeof(serial_no);
+	struct device *dev = &dln2->interface->dev;
+
+	ret = _dln2_transfer(dln2, DLN2_HANDLE_CTRL, CMD_GET_DEVICE_SN, NULL, 0,
+			     &serial_no, &len);
+	if (ret < 0)
+		return ret;
+	if (len < sizeof(serial_no))
+		return -EREMOTEIO;
+
+	dev_info(dev, "Diolan DLN2 serial %u\n", le32_to_cpu(serial_no));
+
+	return 0;
+}
+
+static int dln2_hw_init(struct dln2_dev *dln2)
+{
+	int ret;
+
+	ret = dln2_check_hw(dln2);
+	if (ret < 0)
+		return ret;
+
+	return dln2_print_serialno(dln2);
+}
+
+static void dln2_free_rx_urbs(struct dln2_dev *dln2)
+{
+	int i;
+
+	for (i = 0; i < DLN2_MAX_URBS; i++) {
+		usb_kill_urb(dln2->rx_urb[i]);
+		usb_free_urb(dln2->rx_urb[i]);
+		kfree(dln2->rx_buf[i]);
+	}
+}
+
+static void dln2_free(struct dln2_dev *dln2)
+{
+	dln2_free_rx_urbs(dln2);
+	usb_put_dev(dln2->usb_dev);
+	kfree(dln2);
+}
+
+static int dln2_setup_rx_urbs(struct dln2_dev *dln2,
+			      struct usb_host_interface *hostif)
+{
+	int i;
+	int ret;
+	const int rx_max_size = DLN2_RX_BUF_SIZE;
+	struct device *dev = &dln2->interface->dev;
+
+	for (i = 0; i < DLN2_MAX_URBS; i++) {
+		dln2->rx_buf[i] = kmalloc(rx_max_size, GFP_KERNEL);
+		if (!dln2->rx_buf[i])
+			return -ENOMEM;
+
+		dln2->rx_urb[i] = usb_alloc_urb(0, GFP_KERNEL);
+		if (!dln2->rx_urb[i])
+			return -ENOMEM;
+
+		usb_fill_bulk_urb(dln2->rx_urb[i], dln2->usb_dev,
+				  usb_rcvbulkpipe(dln2->usb_dev, dln2->ep_in),
+				  dln2->rx_buf[i], rx_max_size, dln2_rx, dln2);
+
+		ret = usb_submit_urb(dln2->rx_urb[i], GFP_KERNEL);
+		if (ret < 0) {
+			dev_err(dev, "failed to submit RX URB: %d\n", ret);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+static struct dln2_platform_data dln2_pdata_gpio = {
+	.handle = DLN2_HANDLE_GPIO,
+};
+
+/* Only one I2C port seems to be supported on current hardware */
+static struct dln2_platform_data dln2_pdata_i2c = {
+	.handle = DLN2_HANDLE_I2C,
+	.port = 0,
+};
+
+static const struct mfd_cell dln2_devs[] = {
+	{
+		.name = "dln2-gpio",
+		.platform_data = &dln2_pdata_gpio,
+		.pdata_size = sizeof(struct dln2_platform_data),
+	},
+	{
+		.name = "dln2-i2c",
+		.platform_data = &dln2_pdata_i2c,
+		.pdata_size = sizeof(struct dln2_platform_data),
+	},
+};
+
+static void dln2_disconnect(struct usb_interface *interface)
+{
+	struct dln2_dev *dln2 = usb_get_intfdata(interface);
+	int i, j;
+
+	/* don't allow starting new transfers */
+	spin_lock(&dln2->disconnect_lock);
+	dln2->disconnect = true;
+	spin_unlock(&dln2->disconnect_lock);
+
+	/* cancel in progress transfers */
+	for (i = 0; i < DLN2_HANDLES; i++) {
+		struct dln2_mod_rx_slots *rxs = &dln2->mod_rx_slots[i];
+		unsigned long flags;
+
+		spin_lock_irqsave(&rxs->lock, flags);
+
+		/* cancel all response waiters */
+		for (j = 0; j < DLN2_MAX_RX_SLOTS; j++) {
+			struct dln2_rx_context *rxc = &rxs->slots[j];
+
+			if (rxc->in_use)
+				complete(&rxc->done);
+		}
+
+		spin_unlock_irqrestore(&rxs->lock, flags);
+	}
+
+	/* wait for transfers to end */
+	wait_event(dln2->disconnect_wq, !dln2->active_transfers);
+
+	mfd_remove_devices(&interface->dev);
+
+	dln2_free(dln2);
+}
+
+static int dln2_probe(struct usb_interface *interface,
+		      const struct usb_device_id *usb_id)
+{
+	struct usb_host_interface *hostif = interface->cur_altsetting;
+	struct device *dev = &interface->dev;
+	struct dln2_dev *dln2;
+	int ret;
+	int i, j;
+
+	if (hostif->desc.bInterfaceNumber != 0 ||
+	    hostif->desc.bNumEndpoints < 2)
+		return -ENODEV;
+
+	dln2 = kzalloc(sizeof(*dln2), GFP_KERNEL);
+	if (!dln2)
+		return -ENOMEM;
+
+	dln2->ep_out = hostif->endpoint[0].desc.bEndpointAddress;
+	dln2->ep_in = hostif->endpoint[1].desc.bEndpointAddress;
+	dln2->usb_dev = usb_get_dev(interface_to_usbdev(interface));
+	dln2->interface = interface;
+	usb_set_intfdata(interface, dln2);
+	init_waitqueue_head(&dln2->disconnect_wq);
+
+	for (i = 0; i < DLN2_HANDLES; i++) {
+		init_waitqueue_head(&dln2->mod_rx_slots[i].wq);
+		spin_lock_init(&dln2->mod_rx_slots[i].lock);
+		for (j = 0; j < DLN2_MAX_RX_SLOTS; j++)
+			init_completion(&dln2->mod_rx_slots[i].slots[j].done);
+	}
+
+	spin_lock_init(&dln2->event_cb_lock);
+	spin_lock_init(&dln2->disconnect_lock);
+	INIT_LIST_HEAD(&dln2->event_cb_list);
+
+	ret = dln2_setup_rx_urbs(dln2, hostif);
+	if (ret)
+		goto out_cleanup;
+
+	ret = dln2_hw_init(dln2);
+	if (ret < 0) {
+		dev_err(dev, "failed to initialize hardware\n");
+		goto out_cleanup;
+	}
+
+	ret = mfd_add_hotplug_devices(dev, dln2_devs, ARRAY_SIZE(dln2_devs));
+	if (ret != 0) {
+		dev_err(dev, "failed to add mfd devices to core\n");
+		goto out_cleanup;
+	}
+
+	return 0;
+
+out_cleanup:
+	dln2_free(dln2);
+
+	return ret;
+}
+
+static const struct usb_device_id dln2_table[] = {
+	{ USB_DEVICE(0xa257, 0x2013) },
+	{ }
+};
+
+MODULE_DEVICE_TABLE(usb, dln2_table);
+
+static struct usb_driver dln2_driver = {
+	.name = "dln2",
+	.probe = dln2_probe,
+	.disconnect = dln2_disconnect,
+	.id_table = dln2_table,
+};
+
+module_usb_driver(dln2_driver);
+
+MODULE_AUTHOR("Octavian Purdila <octavian.purdila-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>");
+MODULE_DESCRIPTION("Core driver for the Diolan DLN2 interface adapter");
+MODULE_LICENSE("GPL v2");
diff --git a/include/linux/mfd/dln2.h b/include/linux/mfd/dln2.h
new file mode 100644
index 0000000..004b245
--- /dev/null
+++ b/include/linux/mfd/dln2.h
@@ -0,0 +1,103 @@
+#ifndef __LINUX_USB_DLN2_H
+#define __LINUX_USB_DLN2_H
+
+#define DLN2_CMD(cmd, id)		((cmd) | ((id) << 8))
+
+struct dln2_platform_data {
+	u16 handle;		/* sub-driver handle (internally used only) */
+	u8 port;		/* I2C/SPI port */
+};
+
+/**
+ * dln2_event_cb_t - event callback function signature
+ *
+ * @pdev - the sub-device that registered this callback
+ * @echo - the echo header field received in the message
+ * @data - the data payload
+ * @len  - the data payload length
+ *
+ * The callback function is called in interrupt context and the data payload is
+ * only valid during the call. If the user needs later access of the data, it
+ * must copy it.
+ */
+
+typedef void (*dln2_event_cb_t)(struct platform_device *pdev, u16 echo,
+				const void *data, int len);
+
+/**
+ * dl2n_register_event_cb - register a callback function for an event
+ *
+ * @pdev - the sub-device that registers the callback
+ * @event - the event for which to register a callback
+ * @event_cb - the callback function
+ *
+ * @return 0 in case of success, negative value in case of error
+ */
+int dln2_register_event_cb(struct platform_device *pdev, u16 event,
+			   dln2_event_cb_t event_cb);
+
+/**
+ * dln2_unregister_event_cb - unregister the callback function for an event
+ *
+ * @pdev - the sub-device that registered the callback
+ * @event - the event for which to register a callback
+ */
+void dln2_unregister_event_cb(struct platform_device *pdev, u16 event);
+
+/**
+ * dln2_transfer - issue a DLN2 command and wait for a response and the
+ * associated data
+ *
+ * @pdev - the sub-device which is issuing this transfer
+ * @cmd - the command to be sent to the device
+ * @obuf - the buffer to be sent to the device; it can be NULL if the user
+ *	doesn't need to transmit data with this command
+ * @obuf_len - the size of the buffer to be sent to the device
+ * @ibuf - any data associated with the response will be copied here; it can be
+ *	NULL if the user doesn't need the response data
+ * @ibuf_len - must be initialized to the input buffer size; it will be modified
+ *	to indicate the actual data transferred;
+ *
+ * @return 0 for success, negative value for errors
+ */
+int dln2_transfer(struct platform_device *pdev, u16 cmd,
+		  const void *obuf, unsigned obuf_len,
+		  void *ibuf, unsigned *ibuf_len);
+
+/**
+ * dln2_transfer_rx - variant of @dln2_transfer() where TX buffer is not needed
+ *
+ * @pdev - the sub-device which is issuing this transfer
+ * @cmd - the command to be sent to the device
+ * @ibuf - any data associated with the response will be copied here; it can be
+ *	NULL if the user doesn't need the response data
+ * @ibuf_len - must be initialized to the input buffer size; it will be modified
+ *	to indicate the actual data transferred;
+ *
+ * @return 0 for success, negative value for errors
+ */
+
+static inline int dln2_transfer_rx(struct platform_device *pdev, u16 cmd,
+				   void *ibuf, unsigned *ibuf_len)
+{
+	return dln2_transfer(pdev, cmd, NULL, 0, ibuf, ibuf_len);
+}
+
+/**
+ * dln2_transfer_tx - variant of @dln2_transfer() where RX buffer is not needed
+ *
+ * @pdev - the sub-device which is issuing this transfer
+ * @cmd - the command to be sent to the device
+ * @obuf - the buffer to be sent to the device; it can be NULL if the
+ *	user doesn't need to transmit data with this command
+ * @obuf_len - the size of the buffer to be sent to the device
+ *
+ * @return 0 for success, negative value for errors
+ */
+static inline int dln2_transfer_tx(struct platform_device *pdev, u16 cmd,
+				   const void *obuf, unsigned obuf_len)
+{
+	return dln2_transfer(pdev, cmd, obuf, obuf_len, NULL, NULL);
+}
+
+#endif
-- 
1.9.1

Re: [PATCH v11 1/3] mfd: add support for Diolan DLN-2 devices

[Lee Jones]

On Thu, 06 Nov 2014, Octavian Purdila wrote:

> This patch implements the USB part of the Diolan USB-I2C/SPI/GPIO
> Master Adapter DLN-2. Details about the device can be found here:
> 
> https://www.diolan.com/i2c/i2c_interface.html.
> 
> Information about the USB protocol can be found in the Programmer's
> Reference Manual [1], see section 1.7.
> 
> Because the hardware has a single transmit endpoint and a single
> receive endpoint the communication between the various DLN2 drivers
> and the hardware will be muxed/demuxed by this driver.
> 
> Each DLN2 module will be identified by the handle field within the DLN2
> message header. If a DLN2 module issues multiple commands in parallel
> they will be identified by the echo counter field in the message header.
> 
> The DLN2 modules can use the dln2_transfer() function to issue a
> command and wait for its response. They can also register a callback
> that is going to be called when a specific event id is generated by
> the device (e.g. GPIO interrupts). The device uses handle 0 for
> sending events.
> 
> [1] https://www.diolan.com/downloads/dln-api-manual.pdf
> 
> Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
> Reviewed-by: Johan Hovold <johan@kernel.org>

Great!  Thanks Johan.

> ---
>  drivers/mfd/Kconfig      |  11 +
>  drivers/mfd/Makefile     |   1 +
>  drivers/mfd/dln2.c       | 763 +++++++++++++++++++++++++++++++++++++++++++++++
>  include/linux/mfd/dln2.h | 103 +++++++
>  4 files changed, 878 insertions(+)
>  create mode 100644 drivers/mfd/dln2.c
>  create mode 100644 include/linux/mfd/dln2.h
> 
> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
> index cbdb109..32d7cab 100644
> --- a/drivers/mfd/Kconfig
> +++ b/drivers/mfd/Kconfig
> @@ -189,6 +189,17 @@ config MFD_DA9063
>  	  Additional drivers must be enabled in order to use the functionality
>  	  of the device.
>  
> +config MFD_DLN2
> +	tristate "Diolan DLN2 support"
> +	select MFD_CORE
> +	depends on USB
> +	help
> +

I've removed this line and applied the set.

I will send out a pull-request to the other Maintainers shortly.

[...]

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v11 2/3] i2c: add support for Diolan DLN-2 USB-I2C adapter

[Octavian Purdila]

From: Laurentiu Palcu <laurentiu.palcu-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>

This patch adds support for the Diolan DLN-2 I2C master module. Due
to hardware limitations it does not support SMBUS quick commands.

Information about the USB protocol interface can be found in the
Programmer's Reference Manual [1], see section 6.2.2 for the I2C
master module commands and responses.

[1] https://www.diolan.com/downloads/dln-api-manual.pdf

Signed-off-by: Laurentiu Palcu <laurentiu.palcu-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
Signed-off-by: Octavian Purdila <octavian.purdila-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
Acked-by: Wolfram Sang <wsa-z923LK4zBo2bacvFa/9K2g@public.gmane.org>
Reviewed-by: Johan Hovold <johan-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
---
 drivers/i2c/busses/Kconfig    |  10 ++
 drivers/i2c/busses/Makefile   |   1 +
 drivers/i2c/busses/i2c-dln2.c | 267 ++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 278 insertions(+)
 create mode 100644 drivers/i2c/busses/i2c-dln2.c

diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index 917c358..059e846 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -881,6 +881,16 @@ config I2C_DIOLAN_U2C
 	  This driver can also be built as a module.  If so, the module
 	  will be called i2c-diolan-u2c.
 
+config I2C_DLN2
+       tristate "Diolan DLN-2 USB I2C adapter"
+       depends on MFD_DLN2
+       help
+         If you say yes to this option, support will be included for Diolan
+         DLN2, a USB to I2C interface.
+
+         This driver can also be built as a module.  If so, the module
+         will be called i2c-dln2.
+
 config I2C_PARPORT
 	tristate "Parallel port adapter"
 	depends on PARPORT
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index 78d56c5..cdac7f1 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -87,6 +87,7 @@ obj-$(CONFIG_I2C_RCAR)		+= i2c-rcar.o
 
 # External I2C/SMBus adapter drivers
 obj-$(CONFIG_I2C_DIOLAN_U2C)	+= i2c-diolan-u2c.o
+obj-$(CONFIG_I2C_DLN2)		+= i2c-dln2.o
 obj-$(CONFIG_I2C_PARPORT)	+= i2c-parport.o
 obj-$(CONFIG_I2C_PARPORT_LIGHT)	+= i2c-parport-light.o
 obj-$(CONFIG_I2C_ROBOTFUZZ_OSIF)	+= i2c-robotfuzz-osif.o
diff --git a/drivers/i2c/busses/i2c-dln2.c b/drivers/i2c/busses/i2c-dln2.c
new file mode 100644
index 0000000..010a5fa
--- /dev/null
+++ b/drivers/i2c/busses/i2c-dln2.c
@@ -0,0 +1,267 @@
+/*
+ * Driver for the Diolan DLN-2 USB-I2C adapter
+ *
+ * Copyright (c) 2014 Intel Corporation
+ *
+ * Derived from:
+ *  i2c-diolan-u2c.c
+ *  Copyright (c) 2010-2011 Ericsson AB
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation, version 2.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/slab.h>
+#include <linux/i2c.h>
+#include <linux/platform_device.h>
+#include <linux/mfd/dln2.h>
+
+#define DLN2_I2C_MODULE_ID		0x03
+#define DLN2_I2C_CMD(cmd)		DLN2_CMD(cmd, DLN2_I2C_MODULE_ID)
+
+/* I2C commands */
+#define DLN2_I2C_GET_PORT_COUNT		DLN2_I2C_CMD(0x00)
+#define DLN2_I2C_ENABLE			DLN2_I2C_CMD(0x01)
+#define DLN2_I2C_DISABLE		DLN2_I2C_CMD(0x02)
+#define DLN2_I2C_IS_ENABLED		DLN2_I2C_CMD(0x03)
+#define DLN2_I2C_WRITE			DLN2_I2C_CMD(0x06)
+#define DLN2_I2C_READ			DLN2_I2C_CMD(0x07)
+#define DLN2_I2C_SCAN_DEVICES		DLN2_I2C_CMD(0x08)
+#define DLN2_I2C_PULLUP_ENABLE		DLN2_I2C_CMD(0x09)
+#define DLN2_I2C_PULLUP_DISABLE		DLN2_I2C_CMD(0x0A)
+#define DLN2_I2C_PULLUP_IS_ENABLED	DLN2_I2C_CMD(0x0B)
+#define DLN2_I2C_TRANSFER		DLN2_I2C_CMD(0x0C)
+#define DLN2_I2C_SET_MAX_REPLY_COUNT	DLN2_I2C_CMD(0x0D)
+#define DLN2_I2C_GET_MAX_REPLY_COUNT	DLN2_I2C_CMD(0x0E)
+
+#define DLN2_I2C_MAX_XFER_SIZE		256
+#define DLN2_I2C_BUF_SIZE		(DLN2_I2C_MAX_XFER_SIZE + 16)
+
+struct dln2_i2c {
+	struct platform_device *pdev;
+	struct i2c_adapter adapter;
+	u8 port;
+	/*
+	 * Buffer to hold the packet for read or write transfers. One is enough
+	 * since we can't have multiple transfers in parallel on the i2c bus.
+	 */
+	void *buf;
+};
+
+static int dln2_i2c_enable(struct dln2_i2c *dln2, bool enable)
+{
+	int ret;
+	u16 cmd;
+	struct {
+		u8 port;
+	} tx;
+
+	tx.port = dln2->port;
+
+	if (enable)
+		cmd = DLN2_I2C_ENABLE;
+	else
+		cmd = DLN2_I2C_DISABLE;
+
+	ret = dln2_transfer_tx(dln2->pdev, cmd, &tx, sizeof(tx));
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+
+static int dln2_i2c_write(struct dln2_i2c *dln2, u8 addr,
+			  u8 *data, u16 data_len)
+{
+	int ret;
+	struct {
+		u8 port;
+		u8 addr;
+		u8 mem_addr_len;
+		__le32 mem_addr;
+		__le16 buf_len;
+		u8 buf[DLN2_I2C_MAX_XFER_SIZE];
+	} __packed *tx = dln2->buf;
+	unsigned len;
+
+	BUILD_BUG_ON(sizeof(*tx) > DLN2_I2C_BUF_SIZE);
+
+	tx->port = dln2->port;
+	tx->addr = addr;
+	tx->mem_addr_len = 0;
+	tx->mem_addr = 0;
+	tx->buf_len = cpu_to_le16(data_len);
+	memcpy(tx->buf, data, data_len);
+
+	len = sizeof(*tx) + data_len - DLN2_I2C_MAX_XFER_SIZE;
+	ret = dln2_transfer_tx(dln2->pdev, DLN2_I2C_WRITE, tx, len);
+	if (ret < 0)
+		return ret;
+
+	return data_len;
+}
+
+static int dln2_i2c_read(struct dln2_i2c *dln2, u16 addr, u8 *data,
+			 u16 data_len)
+{
+	int ret;
+	struct {
+		u8 port;
+		u8 addr;
+		u8 mem_addr_len;
+		__le32 mem_addr;
+		__le16 buf_len;
+	} __packed tx;
+	struct {
+		__le16 buf_len;
+		u8 buf[DLN2_I2C_MAX_XFER_SIZE];
+	} __packed *rx = dln2->buf;
+	unsigned rx_len = sizeof(*rx);
+
+	BUILD_BUG_ON(sizeof(*rx) > DLN2_I2C_BUF_SIZE);
+
+	tx.port = dln2->port;
+	tx.addr = addr;
+	tx.mem_addr_len = 0;
+	tx.mem_addr = 0;
+	tx.buf_len = cpu_to_le16(data_len);
+
+	ret = dln2_transfer(dln2->pdev, DLN2_I2C_READ, &tx, sizeof(tx),
+			    rx, &rx_len);
+	if (ret < 0)
+		return ret;
+	if (rx_len < sizeof(rx->buf_len) + data_len)
+		return -EPROTO;
+	if (le16_to_cpu(rx->buf_len) != data_len)
+		return -EPROTO;
+
+	memcpy(data, rx->buf, data_len);
+
+	return data_len;
+}
+
+static int dln2_i2c_xfer(struct i2c_adapter *adapter,
+			 struct i2c_msg *msgs, int num)
+{
+	struct dln2_i2c *dln2 = i2c_get_adapdata(adapter);
+	struct i2c_msg *pmsg;
+	struct device *dev = &dln2->adapter.dev;
+	int i;
+
+	for (i = 0; i < num; i++) {
+		int ret;
+
+		pmsg = &msgs[i];
+
+		if (pmsg->len > DLN2_I2C_MAX_XFER_SIZE) {
+			dev_warn(dev, "maximum transfer size exceeded\n");
+			return -EOPNOTSUPP;
+		}
+
+		if (pmsg->flags & I2C_M_RD) {
+			ret = dln2_i2c_read(dln2, pmsg->addr, pmsg->buf,
+					    pmsg->len);
+			if (ret < 0)
+				return ret;
+
+			pmsg->len = ret;
+		} else {
+			ret = dln2_i2c_write(dln2, pmsg->addr, pmsg->buf,
+					     pmsg->len);
+			if (ret != pmsg->len)
+				return -EPROTO;
+		}
+	}
+
+	return num;
+}
+
+static u32 dln2_i2c_func(struct i2c_adapter *a)
+{
+	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_BYTE | I2C_FUNC_SMBUS_BYTE_DATA |
+		I2C_FUNC_SMBUS_WORD_DATA | I2C_FUNC_SMBUS_BLOCK_PROC_CALL |
+		I2C_FUNC_SMBUS_I2C_BLOCK;
+}
+
+static const struct i2c_algorithm dln2_i2c_usb_algorithm = {
+	.master_xfer = dln2_i2c_xfer,
+	.functionality = dln2_i2c_func,
+};
+
+static int dln2_i2c_probe(struct platform_device *pdev)
+{
+	int ret;
+	struct dln2_i2c *dln2;
+	struct device *dev = &pdev->dev;
+	struct dln2_platform_data *pdata = dev_get_platdata(&pdev->dev);
+
+	dln2 = devm_kzalloc(dev, sizeof(*dln2), GFP_KERNEL);
+	if (!dln2)
+		return -ENOMEM;
+
+	dln2->buf = devm_kmalloc(dev, DLN2_I2C_BUF_SIZE, GFP_KERNEL);
+	if (!dln2->buf)
+		return -ENOMEM;
+
+	dln2->pdev = pdev;
+	dln2->port = pdata->port;
+
+	/* setup i2c adapter description */
+	dln2->adapter.owner = THIS_MODULE;
+	dln2->adapter.class = I2C_CLASS_HWMON;
+	dln2->adapter.algo = &dln2_i2c_usb_algorithm;
+	dln2->adapter.dev.parent = dev;
+	i2c_set_adapdata(&dln2->adapter, dln2);
+	snprintf(dln2->adapter.name, sizeof(dln2->adapter.name), "%s-%s-%d",
+		 "dln2-i2c", dev_name(pdev->dev.parent), dln2->port);
+
+	platform_set_drvdata(pdev, dln2);
+
+	/* initialize the i2c interface */
+	ret = dln2_i2c_enable(dln2, true);
+	if (ret < 0) {
+		dev_err(dev, "failed to initialize adapter: %d\n", ret);
+		return ret;
+	}
+
+	/* and finally attach to i2c layer */
+	ret = i2c_add_adapter(&dln2->adapter);
+	if (ret < 0) {
+		dev_err(dev, "failed to add I2C adapter: %d\n", ret);
+		goto out_disable;
+	}
+
+	return 0;
+
+out_disable:
+	dln2_i2c_enable(dln2, false);
+
+	return ret;
+}
+
+static int dln2_i2c_remove(struct platform_device *pdev)
+{
+	struct dln2_i2c *dln2 = platform_get_drvdata(pdev);
+
+	i2c_del_adapter(&dln2->adapter);
+	dln2_i2c_enable(dln2, false);
+
+	return 0;
+}
+
+static struct platform_driver dln2_i2c_driver = {
+	.driver.name	= "dln2-i2c",
+	.probe		= dln2_i2c_probe,
+	.remove		= dln2_i2c_remove,
+};
+
+module_platform_driver(dln2_i2c_driver);
+
+MODULE_AUTHOR("Laurentiu Palcu <laurentiu.palcu-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>");
+MODULE_DESCRIPTION("Driver for the Diolan DLN2 I2C master interface");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:dln2-i2c");
-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v11 3/3] gpio: add support for the Diolan DLN-2 USB GPIO driver

[Octavian Purdila]

From: Daniel Baluta <daniel.baluta@intel.com>

This patch adds GPIO and IRQ support for the Diolan DLN-2 GPIO module.

Information about the USB protocol interface can be found in the
Programmer's Reference Manual [1], see section 2.9 for the GPIO
module commands and responses.

[1] https://www.diolan.com/downloads/dln-api-manual.pdf

Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
---
 drivers/gpio/Kconfig     |  12 +
 drivers/gpio/Makefile    |   1 +
 drivers/gpio/gpio-dln2.c | 553 +++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 566 insertions(+)
 create mode 100644 drivers/gpio/gpio-dln2.c

diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 0959ca9..23dfd5f 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -905,4 +905,16 @@ config GPIO_VIPERBOARD
           River Tech's viperboard.h for detailed meaning
           of the module parameters.
 
+config GPIO_DLN2
+	tristate "Diolan DLN2 GPIO support"
+	depends on MFD_DLN2
+	select GPIOLIB_IRQCHIP
+
+	help
+	  Select this option to enable GPIO driver for the Diolan DLN2
+	  board.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called gpio-dln2.
+
 endif
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index e5d346c..e60677b 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -26,6 +26,7 @@ obj-$(CONFIG_GPIO_CRYSTAL_COVE)	+= gpio-crystalcove.o
 obj-$(CONFIG_GPIO_DA9052)	+= gpio-da9052.o
 obj-$(CONFIG_GPIO_DA9055)	+= gpio-da9055.o
 obj-$(CONFIG_GPIO_DAVINCI)	+= gpio-davinci.o
+obj-$(CONFIG_GPIO_DLN2)		+= gpio-dln2.o
 obj-$(CONFIG_GPIO_DWAPB)	+= gpio-dwapb.o
 obj-$(CONFIG_GPIO_EM)		+= gpio-em.o
 obj-$(CONFIG_GPIO_EP93XX)	+= gpio-ep93xx.o
diff --git a/drivers/gpio/gpio-dln2.c b/drivers/gpio/gpio-dln2.c
new file mode 100644
index 0000000..978b51e
--- /dev/null
+++ b/drivers/gpio/gpio-dln2.c
@@ -0,0 +1,553 @@
+/*
+ * Driver for the Diolan DLN-2 USB-GPIO adapter
+ *
+ * Copyright (c) 2014 Intel Corporation
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation, version 2.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+#include <linux/irqdomain.h>
+#include <linux/irq.h>
+#include <linux/irqchip/chained_irq.h>
+#include <linux/gpio.h>
+#include <linux/gpio/driver.h>
+#include <linux/platform_device.h>
+#include <linux/mfd/dln2.h>
+
+#define DLN2_GPIO_ID			0x01
+
+#define DLN2_GPIO_GET_PIN_COUNT		DLN2_CMD(0x01, DLN2_GPIO_ID)
+#define DLN2_GPIO_SET_DEBOUNCE		DLN2_CMD(0x04, DLN2_GPIO_ID)
+#define DLN2_GPIO_GET_DEBOUNCE		DLN2_CMD(0x05, DLN2_GPIO_ID)
+#define DLN2_GPIO_PORT_GET_VAL		DLN2_CMD(0x06, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_GET_VAL		DLN2_CMD(0x0B, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_SET_OUT_VAL	DLN2_CMD(0x0C, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_GET_OUT_VAL	DLN2_CMD(0x0D, DLN2_GPIO_ID)
+#define DLN2_GPIO_CONDITION_MET_EV	DLN2_CMD(0x0F, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_ENABLE		DLN2_CMD(0x10, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_DISABLE		DLN2_CMD(0x11, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_SET_DIRECTION	DLN2_CMD(0x13, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_GET_DIRECTION	DLN2_CMD(0x14, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_SET_EVENT_CFG	DLN2_CMD(0x1E, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_GET_EVENT_CFG	DLN2_CMD(0x1F, DLN2_GPIO_ID)
+
+#define DLN2_GPIO_EVENT_NONE		0
+#define DLN2_GPIO_EVENT_CHANGE		1
+#define DLN2_GPIO_EVENT_LVL_HIGH	2
+#define DLN2_GPIO_EVENT_LVL_LOW		3
+#define DLN2_GPIO_EVENT_CHANGE_RISING	0x11
+#define DLN2_GPIO_EVENT_CHANGE_FALLING  0x21
+#define DLN2_GPIO_EVENT_MASK		0x0F
+
+#define DLN2_GPIO_MAX_PINS 32
+
+struct dln2_irq_work {
+	struct work_struct work;
+	struct dln2_gpio *dln2;
+	int pin;
+	int type;
+};
+
+struct dln2_gpio {
+	struct platform_device *pdev;
+	struct gpio_chip gpio;
+
+	/*
+	 * Cache pin direction to save us one transfer, since the hardware has
+	 * separate commands to read the in and out values.
+	 */
+	DECLARE_BITMAP(output_enabled, DLN2_GPIO_MAX_PINS);
+
+	DECLARE_BITMAP(irqs_masked, DLN2_GPIO_MAX_PINS);
+	DECLARE_BITMAP(irqs_enabled, DLN2_GPIO_MAX_PINS);
+	DECLARE_BITMAP(irqs_pending, DLN2_GPIO_MAX_PINS);
+	struct dln2_irq_work *irq_work;
+};
+
+struct dln2_gpio_pin {
+	__le16 pin;
+};
+
+struct dln2_gpio_pin_val {
+	__le16 pin __packed;
+	u8 value;
+};
+
+static int dln2_gpio_get_pin_count(struct platform_device *pdev)
+{
+	int ret;
+	__le16 count;
+	int len = sizeof(count);
+
+	ret = dln2_transfer_rx(pdev, DLN2_GPIO_GET_PIN_COUNT, &count, &len);
+	if (ret < 0)
+		return ret;
+	if (len < sizeof(count))
+		return -EPROTO;
+
+	return le16_to_cpu(count);
+}
+
+static int dln2_gpio_pin_cmd(struct dln2_gpio *dln2, int cmd, unsigned pin)
+{
+	struct dln2_gpio_pin req = {
+		.pin = cpu_to_le16(pin),
+	};
+
+	return dln2_transfer_tx(dln2->pdev, cmd, &req, sizeof(req));
+}
+
+static int dln2_gpio_pin_val(struct dln2_gpio *dln2, int cmd, unsigned int pin)
+{
+	int ret;
+	struct dln2_gpio_pin req = {
+		.pin = cpu_to_le16(pin),
+	};
+	struct dln2_gpio_pin_val rsp;
+	int len = sizeof(rsp);
+
+	ret = dln2_transfer(dln2->pdev, cmd, &req, sizeof(req), &rsp, &len);
+	if (ret < 0)
+		return ret;
+	if (len < sizeof(rsp) || req.pin != rsp.pin)
+		return -EPROTO;
+
+	return rsp.value;
+}
+
+static int dln2_gpio_pin_get_in_val(struct dln2_gpio *dln2, unsigned int pin)
+{
+	int ret;
+
+	ret = dln2_gpio_pin_val(dln2, DLN2_GPIO_PIN_GET_VAL, pin);
+	if (ret < 0)
+		return ret;
+	return !!ret;
+}
+
+static int dln2_gpio_pin_get_out_val(struct dln2_gpio *dln2, unsigned int pin)
+{
+	int ret;
+
+	ret = dln2_gpio_pin_val(dln2, DLN2_GPIO_PIN_GET_OUT_VAL, pin);
+	if (ret < 0)
+		return ret;
+	return !!ret;
+}
+
+static void dln2_gpio_pin_set_out_val(struct dln2_gpio *dln2,
+				      unsigned int pin, int value)
+{
+	struct dln2_gpio_pin_val req = {
+		.pin = cpu_to_le16(pin),
+		.value = value,
+	};
+
+	dln2_transfer_tx(dln2->pdev, DLN2_GPIO_PIN_SET_OUT_VAL, &req,
+			 sizeof(req));
+}
+
+#define DLN2_GPIO_DIRECTION_IN		0
+#define DLN2_GPIO_DIRECTION_OUT		1
+
+static int dln2_gpio_request(struct gpio_chip *chip, unsigned offset)
+{
+	struct dln2_gpio *dln2 = container_of(chip, struct dln2_gpio, gpio);
+	struct dln2_gpio_pin req = {
+		.pin = cpu_to_le16(offset),
+	};
+	struct dln2_gpio_pin_val rsp;
+	int len = sizeof(rsp);
+	int ret;
+
+	ret = dln2_gpio_pin_cmd(dln2, DLN2_GPIO_PIN_ENABLE, offset);
+	if (ret < 0)
+		return ret;
+
+	/* cache the pin direction */
+	ret = dln2_transfer(dln2->pdev, DLN2_GPIO_PIN_GET_DIRECTION,
+			    &req, sizeof(req), &rsp, &len);
+	if (ret < 0)
+		return ret;
+	if (len < sizeof(rsp) || req.pin != rsp.pin) {
+		ret = -EPROTO;
+		goto out_disable;
+	}
+
+	switch (rsp.value) {
+	case DLN2_GPIO_DIRECTION_IN:
+		clear_bit(offset, dln2->output_enabled);
+		return 0;
+	case DLN2_GPIO_DIRECTION_OUT:
+		set_bit(offset, dln2->output_enabled);
+		return 0;
+	default:
+		ret = -EPROTO;
+		goto out_disable;
+	}
+
+out_disable:
+	dln2_gpio_pin_cmd(dln2, DLN2_GPIO_PIN_DISABLE, offset);
+	return ret;
+}
+
+static void dln2_gpio_free(struct gpio_chip *chip, unsigned offset)
+{
+	struct dln2_gpio *dln2 = container_of(chip, struct dln2_gpio, gpio);
+
+	dln2_gpio_pin_cmd(dln2, DLN2_GPIO_PIN_DISABLE, offset);
+}
+
+static int dln2_gpio_get_direction(struct gpio_chip *chip, unsigned offset)
+{
+	struct dln2_gpio *dln2 = container_of(chip, struct dln2_gpio, gpio);
+
+	if (test_bit(offset, dln2->output_enabled))
+		return GPIOF_DIR_OUT;
+
+	return GPIOF_DIR_IN;
+}
+
+static int dln2_gpio_get(struct gpio_chip *chip, unsigned int offset)
+{
+	struct dln2_gpio *dln2 = container_of(chip, struct dln2_gpio, gpio);
+	int dir;
+
+	dir = dln2_gpio_get_direction(chip, offset);
+	if (dir < 0)
+		return dir;
+
+	if (dir == GPIOF_DIR_IN)
+		return dln2_gpio_pin_get_in_val(dln2, offset);
+
+	return dln2_gpio_pin_get_out_val(dln2, offset);
+}
+
+static void dln2_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
+{
+	struct dln2_gpio *dln2 = container_of(chip, struct dln2_gpio, gpio);
+
+	dln2_gpio_pin_set_out_val(dln2, offset, value);
+}
+
+static int dln2_gpio_set_direction(struct gpio_chip *chip, unsigned offset,
+				   unsigned dir)
+{
+	struct dln2_gpio *dln2 = container_of(chip, struct dln2_gpio, gpio);
+	struct dln2_gpio_pin_val req = {
+		.pin = cpu_to_le16(offset),
+		.value = dir,
+	};
+	int ret;
+
+	ret = dln2_transfer_tx(dln2->pdev, DLN2_GPIO_PIN_SET_DIRECTION,
+			       &req, sizeof(req));
+	if (ret < 0)
+		return ret;
+
+	if (dir == DLN2_GPIO_DIRECTION_OUT)
+		set_bit(offset, dln2->output_enabled);
+	else
+		clear_bit(offset, dln2->output_enabled);
+
+	return ret;
+}
+
+static int dln2_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
+{
+	return dln2_gpio_set_direction(chip, offset, DLN2_GPIO_DIRECTION_IN);
+}
+
+static int dln2_gpio_direction_output(struct gpio_chip *chip, unsigned offset,
+				      int value)
+{
+	return dln2_gpio_set_direction(chip, offset, DLN2_GPIO_DIRECTION_OUT);
+}
+
+static int dln2_gpio_set_debounce(struct gpio_chip *chip, unsigned offset,
+				  unsigned debounce)
+{
+	struct dln2_gpio *dln2 = container_of(chip, struct dln2_gpio, gpio);
+	__le32 duration = cpu_to_le32(debounce);
+
+	return dln2_transfer_tx(dln2->pdev, DLN2_GPIO_SET_DEBOUNCE,
+				&duration, sizeof(duration));
+}
+
+static int dln2_gpio_set_event_cfg(struct dln2_gpio *dln2, unsigned pin,
+				   unsigned type, unsigned period)
+{
+	struct {
+		__le16 pin;
+		u8 type;
+		__le16 period;
+	} __packed req = {
+		.pin = cpu_to_le16(pin),
+		.type = type,
+		.period = cpu_to_le16(period),
+	};
+
+	return dln2_transfer_tx(dln2->pdev, DLN2_GPIO_PIN_SET_EVENT_CFG,
+				&req, sizeof(req));
+}
+
+static void dln2_irq_work(struct work_struct *w)
+{
+	struct dln2_irq_work *iw = container_of(w, struct dln2_irq_work, work);
+	struct dln2_gpio *dln2 = iw->dln2;
+	u8 type = iw->type & DLN2_GPIO_EVENT_MASK;
+
+	if (test_bit(iw->pin, dln2->irqs_enabled))
+		dln2_gpio_set_event_cfg(dln2, iw->pin, type, 0);
+	else
+		dln2_gpio_set_event_cfg(dln2, iw->pin, DLN2_GPIO_EVENT_NONE, 0);
+}
+
+static void dln2_irq_enable(struct irq_data *irqd)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+	struct dln2_gpio *dln2 = container_of(gc, struct dln2_gpio, gpio);
+	int pin = irqd_to_hwirq(irqd);
+
+	set_bit(pin, dln2->irqs_enabled);
+	schedule_work(&dln2->irq_work[pin].work);
+}
+
+static void dln2_irq_disable(struct irq_data *irqd)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+	struct dln2_gpio *dln2 = container_of(gc, struct dln2_gpio, gpio);
+	int pin = irqd_to_hwirq(irqd);
+
+	clear_bit(pin, dln2->irqs_enabled);
+	schedule_work(&dln2->irq_work[pin].work);
+}
+
+static void dln2_irq_mask(struct irq_data *irqd)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+	struct dln2_gpio *dln2 = container_of(gc, struct dln2_gpio, gpio);
+	int pin = irqd_to_hwirq(irqd);
+
+	set_bit(pin, dln2->irqs_masked);
+}
+
+static void dln2_irq_unmask(struct irq_data *irqd)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+	struct dln2_gpio *dln2 = container_of(gc, struct dln2_gpio, gpio);
+	struct device *dev = dln2->gpio.dev;
+	int pin = irqd_to_hwirq(irqd);
+
+	if (test_and_clear_bit(pin, dln2->irqs_pending)) {
+		int irq;
+
+		irq = irq_find_mapping(dln2->gpio.irqdomain, pin);
+		if (!irq) {
+			dev_err(dev, "pin %d not mapped to IRQ\n", pin);
+			return;
+		}
+
+		generic_handle_irq(irq);
+	}
+}
+
+static int dln2_irq_set_type(struct irq_data *irqd, unsigned type)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+	struct dln2_gpio *dln2 = container_of(gc, struct dln2_gpio, gpio);
+	int pin = irqd_to_hwirq(irqd);
+
+	switch (type) {
+	case IRQ_TYPE_LEVEL_HIGH:
+		dln2->irq_work[pin].type = DLN2_GPIO_EVENT_LVL_HIGH;
+		break;
+	case IRQ_TYPE_LEVEL_LOW:
+		dln2->irq_work[pin].type = DLN2_GPIO_EVENT_LVL_LOW;
+		break;
+	case IRQ_TYPE_EDGE_BOTH:
+		dln2->irq_work[pin].type = DLN2_GPIO_EVENT_CHANGE;
+		break;
+	case IRQ_TYPE_EDGE_RISING:
+		dln2->irq_work[pin].type = DLN2_GPIO_EVENT_CHANGE_RISING;
+		break;
+	case IRQ_TYPE_EDGE_FALLING:
+		dln2->irq_work[pin].type = DLN2_GPIO_EVENT_CHANGE_FALLING;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static struct irq_chip dln2_gpio_irqchip = {
+	.name = "dln2-irq",
+	.irq_enable = dln2_irq_enable,
+	.irq_disable = dln2_irq_disable,
+	.irq_mask = dln2_irq_mask,
+	.irq_unmask = dln2_irq_unmask,
+	.irq_set_type = dln2_irq_set_type,
+};
+
+static void dln2_gpio_event(struct platform_device *pdev, u16 echo,
+			    const void *data, int len)
+{
+	int pin, irq;
+	const struct {
+		__le16 count;
+		__u8 type;
+		__le16 pin;
+		__u8 value;
+	} __packed *event = data;
+	struct dln2_gpio *dln2 = platform_get_drvdata(pdev);
+
+	if (len < sizeof(*event)) {
+		dev_err(dln2->gpio.dev, "short event message\n");
+		return;
+	}
+
+	pin = le16_to_cpu(event->pin);
+	if (pin >= dln2->gpio.ngpio) {
+		dev_err(dln2->gpio.dev, "out of bounds pin %d\n", pin);
+		return;
+	}
+
+	irq = irq_find_mapping(dln2->gpio.irqdomain, pin);
+	if (!irq) {
+		dev_err(dln2->gpio.dev, "pin %d not mapped to IRQ\n", pin);
+		return;
+	}
+
+	if (!test_bit(pin, dln2->irqs_enabled))
+		return;
+	if (test_bit(pin, dln2->irqs_masked)) {
+		set_bit(pin, dln2->irqs_pending);
+		return;
+	}
+
+	switch (dln2->irq_work[pin].type) {
+	case DLN2_GPIO_EVENT_CHANGE_RISING:
+		if (event->value)
+			generic_handle_irq(irq);
+		break;
+	case DLN2_GPIO_EVENT_CHANGE_FALLING:
+		if (!event->value)
+			generic_handle_irq(irq);
+		break;
+	default:
+		generic_handle_irq(irq);
+	}
+}
+
+static int dln2_gpio_probe(struct platform_device *pdev)
+{
+	struct dln2_gpio *dln2;
+	struct device *dev = &pdev->dev;
+	int pins;
+	int i, ret;
+
+	pins = dln2_gpio_get_pin_count(pdev);
+	if (pins < 0) {
+		dev_err(dev, "failed to get pin count: %d\n", pins);
+		return pins;
+	}
+	if (pins > DLN2_GPIO_MAX_PINS) {
+		pins = DLN2_GPIO_MAX_PINS;
+		dev_warn(dev, "clamping pins to %d\n", DLN2_GPIO_MAX_PINS);
+	}
+
+	dln2 = devm_kzalloc(&pdev->dev, sizeof(*dln2), GFP_KERNEL);
+	if (!dln2)
+		return -ENOMEM;
+
+	dln2->irq_work = devm_kcalloc(&pdev->dev, pins,
+				      sizeof(struct dln2_irq_work), GFP_KERNEL);
+	if (!dln2->irq_work)
+		return -ENOMEM;
+	for (i = 0; i < pins; i++) {
+		INIT_WORK(&dln2->irq_work[i].work, dln2_irq_work);
+		dln2->irq_work[i].pin = i;
+		dln2->irq_work[i].dln2 = dln2;
+	}
+
+	dln2->pdev = pdev;
+
+	dln2->gpio.label = "dln2";
+	dln2->gpio.dev = dev;
+	dln2->gpio.owner = THIS_MODULE;
+	dln2->gpio.base = -1;
+	dln2->gpio.ngpio = pins;
+	dln2->gpio.exported = true;
+	dln2->gpio.can_sleep = true;
+	dln2->gpio.irq_not_threaded = true;
+	dln2->gpio.set = dln2_gpio_set;
+	dln2->gpio.get = dln2_gpio_get;
+	dln2->gpio.request = dln2_gpio_request;
+	dln2->gpio.free = dln2_gpio_free;
+	dln2->gpio.get_direction = dln2_gpio_get_direction;
+	dln2->gpio.direction_input = dln2_gpio_direction_input;
+	dln2->gpio.direction_output = dln2_gpio_direction_output;
+	dln2->gpio.set_debounce = dln2_gpio_set_debounce;
+
+	platform_set_drvdata(pdev, dln2);
+
+	ret = gpiochip_add(&dln2->gpio);
+	if (ret < 0) {
+		dev_err(dev, "failed to add gpio chip: %d\n", ret);
+		goto out;
+	}
+
+	ret = gpiochip_irqchip_add(&dln2->gpio, &dln2_gpio_irqchip, 0,
+				   handle_simple_irq, IRQ_TYPE_NONE);
+	if (ret < 0) {
+		dev_err(dev, "failed to add irq chip: %d\n", ret);
+		goto out_gpiochip_remove;
+	}
+
+	ret = dln2_register_event_cb(pdev, DLN2_GPIO_CONDITION_MET_EV,
+				     dln2_gpio_event);
+	if (ret) {
+		dev_err(dev, "failed to register event cb: %d\n", ret);
+		goto out_gpiochip_remove;
+	}
+
+	return 0;
+
+out_gpiochip_remove:
+	gpiochip_remove(&dln2->gpio);
+out:
+	return ret;
+}
+
+static int dln2_gpio_remove(struct platform_device *pdev)
+{
+	struct dln2_gpio *dln2 = platform_get_drvdata(pdev);
+	int i;
+
+	dln2_unregister_event_cb(pdev, DLN2_GPIO_CONDITION_MET_EV);
+	for (i = 0; i < dln2->gpio.ngpio; i++)
+		flush_work(&dln2->irq_work[i].work);
+	gpiochip_remove(&dln2->gpio);
+
+	return 0;
+}
+
+static struct platform_driver dln2_gpio_driver = {
+	.driver.name	= "dln2-gpio",
+	.probe		= dln2_gpio_probe,
+	.remove		= dln2_gpio_remove,
+};
+
+module_platform_driver(dln2_gpio_driver);
+
+MODULE_AUTHOR("Daniel Baluta <daniel.baluta@intel.com");
+MODULE_DESCRIPTION("Driver for the Diolan DLN2 GPIO interface");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:dln2-gpio");
-- 
1.9.1

Re: [PATCH v11 0/3] add support for Diolan DLN-2

[Lee Jones]

Linus, Wolfram,

Enjoy!

The following changes since commit f114040e3ea6e07372334ade75d1ee0775c355e1:

  Linux 3.18-rc1 (2014-10-19 18:08:38 -0700)

are available in the git repository at:

  git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd.git tags/ib-mfd-gpio-i2c-v3.19

for you to fetch changes up to e7d146b11a8a33b6033220b0f4fc4de2ab29218a:

  gpio: add support for the Diolan DLN-2 USB GPIO driver (2014-11-10 15:05:49 +0000)

----------------------------------------------------------------
Immutable branch between MFD, GPIO and I2C

----------------------------------------------------------------
Daniel Baluta (1):
      gpio: add support for the Diolan DLN-2 USB GPIO driver

Laurentiu Palcu (1):
      i2c: add support for Diolan DLN-2 USB-I2C adapter

Octavian Purdila (1):
      mfd: Add support for Diolan DLN-2 devices

 drivers/gpio/Kconfig          |  12 +
 drivers/gpio/Makefile         |   1 +
 drivers/gpio/gpio-dln2.c      | 553 ++++++++++++++++++++++++++++++
 drivers/i2c/busses/Kconfig    |  10 +
 drivers/i2c/busses/Makefile   |   1 +
 drivers/i2c/busses/i2c-dln2.c | 267 +++++++++++++++
 drivers/mfd/Kconfig           |  10 +
 drivers/mfd/Makefile          |   1 +
 drivers/mfd/dln2.c            | 763 ++++++++++++++++++++++++++++++++++++++++++
 include/linux/mfd/dln2.h      | 103 ++++++
 10 files changed, 1721 insertions(+)
 create mode 100644 drivers/gpio/gpio-dln2.c
 create mode 100644 drivers/i2c/busses/i2c-dln2.c
 create mode 100644 drivers/mfd/dln2.c
 create mode 100644 include/linux/mfd/dln2.h

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH v11 0/3] add support for Diolan DLN-2

[Octavian Purdila]

On Mon, Nov 10, 2014 at 5:10 PM, Lee Jones <lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org> wrote:
> Linus, Wolfram,
>
> Enjoy!
>
> The following changes since commit f114040e3ea6e07372334ade75d1ee0775c355e1:
>
>   Linux 3.18-rc1 (2014-10-19 18:08:38 -0700)
>
> are available in the git repository at:
>
>   git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd.git tags/ib-mfd-gpio-i2c-v3.19

Hi Lee,

Not sure if this matter, but this tree seems to miss the
mfd_add_hotplug_devices patches from Johan, which are needed by the
patches below.

>
> for you to fetch changes up to e7d146b11a8a33b6033220b0f4fc4de2ab29218a:
>
>   gpio: add support for the Diolan DLN-2 USB GPIO driver (2014-11-10 15:05:49 +0000)
>
> ----------------------------------------------------------------
> Immutable branch between MFD, GPIO and I2C
>
> ----------------------------------------------------------------
> Daniel Baluta (1):
>       gpio: add support for the Diolan DLN-2 USB GPIO driver
>
> Laurentiu Palcu (1):
>       i2c: add support for Diolan DLN-2 USB-I2C adapter
>
> Octavian Purdila (1):
>       mfd: Add support for Diolan DLN-2 devices
>
>  drivers/gpio/Kconfig          |  12 +
>  drivers/gpio/Makefile         |   1 +
>  drivers/gpio/gpio-dln2.c      | 553 ++++++++++++++++++++++++++++++
>  drivers/i2c/busses/Kconfig    |  10 +
>  drivers/i2c/busses/Makefile   |   1 +
>  drivers/i2c/busses/i2c-dln2.c | 267 +++++++++++++++
>  drivers/mfd/Kconfig           |  10 +
>  drivers/mfd/Makefile          |   1 +
>  drivers/mfd/dln2.c            | 763 ++++++++++++++++++++++++++++++++++++++++++
>  include/linux/mfd/dln2.h      | 103 ++++++
>  10 files changed, 1721 insertions(+)
>  create mode 100644 drivers/gpio/gpio-dln2.c
>  create mode 100644 drivers/i2c/busses/i2c-dln2.c
>  create mode 100644 drivers/mfd/dln2.c
>  create mode 100644 include/linux/mfd/dln2.h
>
> --
> Lee Jones
> Linaro STMicroelectronics Landing Team Lead
> Linaro.org │ Open source software for ARM SoCs
> Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH v11 0/3] add support for Diolan DLN-2

[Lee Jones]

On Mon, 10 Nov 2014, Octavian Purdila wrote:

> On Mon, Nov 10, 2014 at 5:10 PM, Lee Jones <lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org> wrote:
> > Linus, Wolfram,
> >
> > Enjoy!
> >
> > The following changes since commit f114040e3ea6e07372334ade75d1ee0775c355e1:
> >
> >   Linux 3.18-rc1 (2014-10-19 18:08:38 -0700)
> >
> > are available in the git repository at:
> >
> >   git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd.git tags/ib-mfd-gpio-i2c-v3.19
> 
> Hi Lee,
> 
> Not sure if this matter, but this tree seems to miss the
> mfd_add_hotplug_devices patches from Johan, which are needed by the
> patches below.

Yes, that will definitely matter.

> > for you to fetch changes up to e7d146b11a8a33b6033220b0f4fc4de2ab29218a:
> >
> >   gpio: add support for the Diolan DLN-2 USB GPIO driver (2014-11-10 15:05:49 +0000)
> >
> > ----------------------------------------------------------------
> > Immutable branch between MFD, GPIO and I2C
> >
> > ----------------------------------------------------------------
> > Daniel Baluta (1):
> >       gpio: add support for the Diolan DLN-2 USB GPIO driver
> >
> > Laurentiu Palcu (1):
> >       i2c: add support for Diolan DLN-2 USB-I2C adapter
> >
> > Octavian Purdila (1):
> >       mfd: Add support for Diolan DLN-2 devices
> >
> >  drivers/gpio/Kconfig          |  12 +
> >  drivers/gpio/Makefile         |   1 +
> >  drivers/gpio/gpio-dln2.c      | 553 ++++++++++++++++++++++++++++++
> >  drivers/i2c/busses/Kconfig    |  10 +
> >  drivers/i2c/busses/Makefile   |   1 +
> >  drivers/i2c/busses/i2c-dln2.c | 267 +++++++++++++++
> >  drivers/mfd/Kconfig           |  10 +
> >  drivers/mfd/Makefile          |   1 +
> >  drivers/mfd/dln2.c            | 763 ++++++++++++++++++++++++++++++++++++++++++
> >  include/linux/mfd/dln2.h      | 103 ++++++
> >  10 files changed, 1721 insertions(+)
> >  create mode 100644 drivers/gpio/gpio-dln2.c
> >  create mode 100644 drivers/i2c/busses/i2c-dln2.c
> >  create mode 100644 drivers/mfd/dln2.c
> >  create mode 100644 include/linux/mfd/dln2.h
> >

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

[GIT PULL] Immutable branch between MFD, GPIO and I2C

[Lee Jones]

[Subject change -- in case you miss it]

Linus, Wolfram,

Enjoy!

The following changes since commit f114040e3ea6e07372334ade75d1ee0775c355e1:

  Linux 3.18-rc1 (2014-10-19 18:08:38 -0700)

are available in the git repository at:

  git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd.git tags/ib-mfd-gpio-i2c-v3.19

for you to fetch changes up to e7d146b11a8a33b6033220b0f4fc4de2ab29218a:

  gpio: add support for the Diolan DLN-2 USB GPIO driver (2014-11-10 15:05:49 +0000)

----------------------------------------------------------------
Immutable branch between MFD, GPIO and I2C

----------------------------------------------------------------
Daniel Baluta (1):
      gpio: add support for the Diolan DLN-2 USB GPIO driver

Laurentiu Palcu (1):
      i2c: add support for Diolan DLN-2 USB-I2C adapter

Octavian Purdila (1):
      mfd: Add support for Diolan DLN-2 devices

 drivers/gpio/Kconfig          |  12 +
 drivers/gpio/Makefile         |   1 +
 drivers/gpio/gpio-dln2.c      | 553 ++++++++++++++++++++++++++++++
 drivers/i2c/busses/Kconfig    |  10 +
 drivers/i2c/busses/Makefile   |   1 +
 drivers/i2c/busses/i2c-dln2.c | 267 +++++++++++++++
 drivers/mfd/Kconfig           |  10 +
 drivers/mfd/Makefile          |   1 +
 drivers/mfd/dln2.c            | 763 ++++++++++++++++++++++++++++++++++++++++++
 include/linux/mfd/dln2.h      | 103 ++++++
 10 files changed, 1721 insertions(+)
 create mode 100644 drivers/gpio/gpio-dln2.c
 create mode 100644 drivers/i2c/busses/i2c-dln2.c
 create mode 100644 drivers/mfd/dln2.c
 create mode 100644 include/linux/mfd/dln2.h

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [GIT PULL] Immutable branch between MFD, GPIO and I2C

[Lee Jones]

Please don't pull this -- it is missing a patch.

Will fix.

> [Subject change -- in case you miss it]
> 
> Linus, Wolfram,
> 
> Enjoy!
> 
> The following changes since commit f114040e3ea6e07372334ade75d1ee0775c355e1:
> 
>   Linux 3.18-rc1 (2014-10-19 18:08:38 -0700)
> 
> are available in the git repository at:
> 
>   git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd.git tags/ib-mfd-gpio-i2c-v3.19
> 
> for you to fetch changes up to e7d146b11a8a33b6033220b0f4fc4de2ab29218a:
> 
>   gpio: add support for the Diolan DLN-2 USB GPIO driver (2014-11-10 15:05:49 +0000)
> 
> ----------------------------------------------------------------
> Immutable branch between MFD, GPIO and I2C
> 
> ----------------------------------------------------------------
> Daniel Baluta (1):
>       gpio: add support for the Diolan DLN-2 USB GPIO driver
> 
> Laurentiu Palcu (1):
>       i2c: add support for Diolan DLN-2 USB-I2C adapter
> 
> Octavian Purdila (1):
>       mfd: Add support for Diolan DLN-2 devices
> 
>  drivers/gpio/Kconfig          |  12 +
>  drivers/gpio/Makefile         |   1 +
>  drivers/gpio/gpio-dln2.c      | 553 ++++++++++++++++++++++++++++++
>  drivers/i2c/busses/Kconfig    |  10 +
>  drivers/i2c/busses/Makefile   |   1 +
>  drivers/i2c/busses/i2c-dln2.c | 267 +++++++++++++++
>  drivers/mfd/Kconfig           |  10 +
>  drivers/mfd/Makefile          |   1 +
>  drivers/mfd/dln2.c            | 763 ++++++++++++++++++++++++++++++++++++++++++
>  include/linux/mfd/dln2.h      | 103 ++++++
>  10 files changed, 1721 insertions(+)
>  create mode 100644 drivers/gpio/gpio-dln2.c
>  create mode 100644 drivers/i2c/busses/i2c-dln2.c
>  create mode 100644 drivers/mfd/dln2.c
>  create mode 100644 include/linux/mfd/dln2.h
> 

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [GIT PULL] Immutable branch between MFD, GPIO and I2C

[Lee Jones]

> Please don't pull this -- it is missing a patch.
> 
> Will fix.

Okay, dependency fixed.  Sorry for the fuss.  Pull when ready.

> > [Subject change -- in case you miss it]
> > 
> > Linus, Wolfram,
> > 
> > Enjoy!
> > 
> > The following changes since commit f114040e3ea6e07372334ade75d1ee0775c355e1:
> > 
> >   Linux 3.18-rc1 (2014-10-19 18:08:38 -0700)
> > 
> > are available in the git repository at:
> > 
> >   git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd.git tags/ib-mfd-gpio-i2c-v3.19
> > 
> > for you to fetch changes up to e7d146b11a8a33b6033220b0f4fc4de2ab29218a:
> > 
> >   gpio: add support for the Diolan DLN-2 USB GPIO driver (2014-11-10 15:05:49 +0000)
> > 
> > ----------------------------------------------------------------
> > Immutable branch between MFD, GPIO and I2C
> > 
> > ----------------------------------------------------------------
> > Daniel Baluta (1):
> >       gpio: add support for the Diolan DLN-2 USB GPIO driver
> > 
> > Laurentiu Palcu (1):
> >       i2c: add support for Diolan DLN-2 USB-I2C adapter
> > 
> > Octavian Purdila (1):
> >       mfd: Add support for Diolan DLN-2 devices
> > 
> >  drivers/gpio/Kconfig          |  12 +
> >  drivers/gpio/Makefile         |   1 +
> >  drivers/gpio/gpio-dln2.c      | 553 ++++++++++++++++++++++++++++++
> >  drivers/i2c/busses/Kconfig    |  10 +
> >  drivers/i2c/busses/Makefile   |   1 +
> >  drivers/i2c/busses/i2c-dln2.c | 267 +++++++++++++++
> >  drivers/mfd/Kconfig           |  10 +
> >  drivers/mfd/Makefile          |   1 +
> >  drivers/mfd/dln2.c            | 763 ++++++++++++++++++++++++++++++++++++++++++
> >  include/linux/mfd/dln2.h      | 103 ++++++
> >  10 files changed, 1721 insertions(+)
> >  create mode 100644 drivers/gpio/gpio-dln2.c
> >  create mode 100644 drivers/i2c/busses/i2c-dln2.c
> >  create mode 100644 drivers/mfd/dln2.c
> >  create mode 100644 include/linux/mfd/dln2.h
> > 
> 

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [GIT PULL] Immutable branch between MFD, GPIO and I2C

[Linus Walleij]

On Mon, Nov 10, 2014 at 6:43 PM, Lee Jones <lee.jones@linaro.org> wrote:
>> Please don't pull this -- it is missing a patch.
>>
>> Will fix.
>
> Okay, dependency fixed.  Sorry for the fuss.  Pull when ready.

Letting it just sit around unless there are conflicts coming up...
Seems like this can go through MFD alone from the GPIO side
of things.

Yours,
Linus Walleij