From: "Niklas Söderlund" <niklas.soderlund@ragnatech.se>
To: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>,
Linus Walleij <linus.walleij@linaro.org>,
linux-renesas-soc@vger.kernel.org, linux-gpio@vger.kernel.org
Subject: Re: [PATCHv2 4/6] pinctrl: sh-pfc: r8a7795: Use lookup function for bias data
Date: Sat, 12 Nov 2016 14:44:41 +0100 [thread overview]
Message-ID: <20161112134441.GD3834@bigcity.dyn.berto.se> (raw)
In-Reply-To: <2290994.VU9FGZyxlz@avalon>
Hi Laurent,
Thanks for your feedback!
On 2016-11-12 03:47:50 +0200, Laurent Pinchart wrote:
> Hi Niklas,
>
> Thank you for the patch.
>
> On Friday 11 Nov 2016 21:30:19 Niklas Söderlund wrote:
> > From: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
> >
> > There is a bug in the r8a7795 bias code where a WARN() is trigged
> > anytime a pin from PUEN0/PUD0is accessed.
> >
> > # cat /sys/kernel/debug/pinctrl/e6060000.pfc/pinconf-pins
> >
> > WARNING: CPU: 2 PID: 2391 at drivers/pinctrl/sh-pfc/pfc-r8a7795.c:5364
> > r8a7795_pinmux_get_bias+0xbc/0xc8 [..]
> > Call trace:
> > [<ffff0000083c442c>] r8a7795_pinmux_get_bias+0xbc/0xc8
> > [<ffff0000083c37f4>] sh_pfc_pinconf_get+0x194/0x270
> > [<ffff0000083b0768>] pin_config_get_for_pin+0x20/0x30
> > [<ffff0000083b11e8>] pinconf_generic_dump_one+0x168/0x188
> > [<ffff0000083b144c>] pinconf_generic_dump_pins+0x5c/0x98
> > [<ffff0000083b0628>] pinconf_pins_show+0xc8/0x128
> > [<ffff0000081fe3bc>] seq_read+0x16c/0x420
> > [<ffff00000831a110>] full_proxy_read+0x58/0x88
> > [<ffff0000081d7ad4>] __vfs_read+0x1c/0xf8
> > [<ffff0000081d8874>] vfs_read+0x84/0x148
> > [<ffff0000081d9d64>] SyS_read+0x44/0xa0
> > [<ffff000008082f4c>] __sys_trace_return+0x0/0x4
> >
> > This is due to the WARN() check if the reg field of the pullups struct
> > is zero, and this should be 0 for pins controlled by the PUEN0/PUD0
> > registers since PU0 is defined as 0. Change the data structure and use
> > the generic sh_pfc_pin_to_bias_info() function to get the register
> > offset and bit information.
> >
> > Fixes: 560655247b627ac7 ("pinctrl: sh-pfc: r8a7795: Add bias pinconf
> > support")
> > Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
> > ---
> > drivers/pinctrl/sh-pfc/pfc-r8a7795.c | 341 ++++++++++++++------------------
> > 1 file changed, 170 insertions(+), 171 deletions(-)
> >
> > diff --git a/drivers/pinctrl/sh-pfc/pfc-r8a7795.c
> > b/drivers/pinctrl/sh-pfc/pfc-r8a7795.c index 6c58563..01ca592 100644
> > --- a/drivers/pinctrl/sh-pfc/pfc-r8a7795.c
> > +++ b/drivers/pinctrl/sh-pfc/pfc-r8a7795.c
> > @@ -5188,171 +5188,168 @@ static int r8a7795_pin_to_pocctrl(struct sh_pfc
> > *pfc, unsigned int pin, u32 *poc #define PU5 0x14
> > #define PU6 0x18
> >
> > -static const struct {
> > - u16 reg : 11;
> > - u16 bit : 5;
> > -} pullups[] = {
> > - [RCAR_GP_PIN(2, 11)] = { PU0, 31 }, /* AVB_PHY_INT */
> > - [RCAR_GP_PIN(2, 10)] = { PU0, 30 }, /* AVB_MAGIC */
> > - [RCAR_GP_PIN(2, 9)] = { PU0, 29 }, /* AVB_MDC */
> > -
> > - [RCAR_GP_PIN(1, 19)] = { PU1, 31 }, /* A19 */
> > - [RCAR_GP_PIN(1, 18)] = { PU1, 30 }, /* A18 */
> > - [RCAR_GP_PIN(1, 17)] = { PU1, 29 }, /* A17 */
> > - [RCAR_GP_PIN(1, 16)] = { PU1, 28 }, /* A16 */
> > - [RCAR_GP_PIN(1, 15)] = { PU1, 27 }, /* A15 */
> > - [RCAR_GP_PIN(1, 14)] = { PU1, 26 }, /* A14 */
> > - [RCAR_GP_PIN(1, 13)] = { PU1, 25 }, /* A13 */
> > - [RCAR_GP_PIN(1, 12)] = { PU1, 24 }, /* A12 */
> > - [RCAR_GP_PIN(1, 11)] = { PU1, 23 }, /* A11 */
> > - [RCAR_GP_PIN(1, 10)] = { PU1, 22 }, /* A10 */
> > - [RCAR_GP_PIN(1, 9)] = { PU1, 21 }, /* A9 */
> > - [RCAR_GP_PIN(1, 8)] = { PU1, 20 }, /* A8 */
> > - [RCAR_GP_PIN(1, 7)] = { PU1, 19 }, /* A7 */
> > - [RCAR_GP_PIN(1, 6)] = { PU1, 18 }, /* A6 */
> > - [RCAR_GP_PIN(1, 5)] = { PU1, 17 }, /* A5 */
> > - [RCAR_GP_PIN(1, 4)] = { PU1, 16 }, /* A4 */
> > - [RCAR_GP_PIN(1, 3)] = { PU1, 15 }, /* A3 */
> > - [RCAR_GP_PIN(1, 2)] = { PU1, 14 }, /* A2 */
> > - [RCAR_GP_PIN(1, 1)] = { PU1, 13 }, /* A1 */
> > - [RCAR_GP_PIN(1, 0)] = { PU1, 12 }, /* A0 */
> > - [RCAR_GP_PIN(2, 8)] = { PU1, 11 }, /* PWM2_A */
> > - [RCAR_GP_PIN(2, 7)] = { PU1, 10 }, /* PWM1_A */
> > - [RCAR_GP_PIN(2, 6)] = { PU1, 9 }, /* PWM0 */
> > - [RCAR_GP_PIN(2, 5)] = { PU1, 8 }, /* IRQ5 */
> > - [RCAR_GP_PIN(2, 4)] = { PU1, 7 }, /* IRQ4 */
> > - [RCAR_GP_PIN(2, 3)] = { PU1, 6 }, /* IRQ3 */
> > - [RCAR_GP_PIN(2, 2)] = { PU1, 5 }, /* IRQ2 */
> > - [RCAR_GP_PIN(2, 1)] = { PU1, 4 }, /* IRQ1 */
> > - [RCAR_GP_PIN(2, 0)] = { PU1, 3 }, /* IRQ0 */
> > - [RCAR_GP_PIN(2, 14)] = { PU1, 2 }, /* AVB_AVTP_CAPTURE_A */
> > - [RCAR_GP_PIN(2, 13)] = { PU1, 1 }, /* AVB_AVTP_MATCH_A */
> > - [RCAR_GP_PIN(2, 12)] = { PU1, 0 }, /* AVB_LINK */
> > -
> > - [RCAR_GP_PIN(7, 3)] = { PU2, 29 }, /* HDMI1_CEC */
> > - [RCAR_GP_PIN(7, 2)] = { PU2, 28 }, /* HDMI0_CEC */
> > - [RCAR_GP_PIN(7, 1)] = { PU2, 27 }, /* AVS2 */
> > - [RCAR_GP_PIN(7, 0)] = { PU2, 26 }, /* AVS1 */
> > - [RCAR_GP_PIN(0, 15)] = { PU2, 25 }, /* D15 */
> > - [RCAR_GP_PIN(0, 14)] = { PU2, 24 }, /* D14 */
> > - [RCAR_GP_PIN(0, 13)] = { PU2, 23 }, /* D13 */
> > - [RCAR_GP_PIN(0, 12)] = { PU2, 22 }, /* D12 */
> > - [RCAR_GP_PIN(0, 11)] = { PU2, 21 }, /* D11 */
> > - [RCAR_GP_PIN(0, 10)] = { PU2, 20 }, /* D10 */
> > - [RCAR_GP_PIN(0, 9)] = { PU2, 19 }, /* D9 */
> > - [RCAR_GP_PIN(0, 8)] = { PU2, 18 }, /* D8 */
> > - [RCAR_GP_PIN(0, 7)] = { PU2, 17 }, /* D7 */
> > - [RCAR_GP_PIN(0, 6)] = { PU2, 16 }, /* D6 */
> > - [RCAR_GP_PIN(0, 5)] = { PU2, 15 }, /* D5 */
> > - [RCAR_GP_PIN(0, 4)] = { PU2, 14 }, /* D4 */
> > - [RCAR_GP_PIN(0, 3)] = { PU2, 13 }, /* D3 */
> > - [RCAR_GP_PIN(0, 2)] = { PU2, 12 }, /* D2 */
> > - [RCAR_GP_PIN(0, 1)] = { PU2, 11 }, /* D1 */
> > - [RCAR_GP_PIN(0, 0)] = { PU2, 10 }, /* D0 */
> > - [RCAR_GP_PIN(1, 27)] = { PU2, 8 }, /* EX_WAIT0_A */
> > - [RCAR_GP_PIN(1, 26)] = { PU2, 7 }, /* WE1_N */
> > - [RCAR_GP_PIN(1, 25)] = { PU2, 6 }, /* WE0_N */
> > - [RCAR_GP_PIN(1, 24)] = { PU2, 5 }, /* RD_WR_N */
> > - [RCAR_GP_PIN(1, 23)] = { PU2, 4 }, /* RD_N */
> > - [RCAR_GP_PIN(1, 22)] = { PU2, 3 }, /* BS_N */
> > - [RCAR_GP_PIN(1, 21)] = { PU2, 2 }, /* CS1_N_A26 */
> > - [RCAR_GP_PIN(1, 20)] = { PU2, 1 }, /* CS0_N */
> > -
> > - [RCAR_GP_PIN(4, 9)] = { PU3, 31 }, /* SD3_DAT0 */
> > - [RCAR_GP_PIN(4, 8)] = { PU3, 30 }, /* SD3_CMD */
> > - [RCAR_GP_PIN(4, 7)] = { PU3, 29 }, /* SD3_CLK */
> > - [RCAR_GP_PIN(4, 6)] = { PU3, 28 }, /* SD2_DS */
> > - [RCAR_GP_PIN(4, 5)] = { PU3, 27 }, /* SD2_DAT3 */
> > - [RCAR_GP_PIN(4, 4)] = { PU3, 26 }, /* SD2_DAT2 */
> > - [RCAR_GP_PIN(4, 3)] = { PU3, 25 }, /* SD2_DAT1 */
> > - [RCAR_GP_PIN(4, 2)] = { PU3, 24 }, /* SD2_DAT0 */
> > - [RCAR_GP_PIN(4, 1)] = { PU3, 23 }, /* SD2_CMD */
> > - [RCAR_GP_PIN(4, 0)] = { PU3, 22 }, /* SD2_CLK */
> > - [RCAR_GP_PIN(3, 11)] = { PU3, 21 }, /* SD1_DAT3 */
> > - [RCAR_GP_PIN(3, 10)] = { PU3, 20 }, /* SD1_DAT2 */
> > - [RCAR_GP_PIN(3, 9)] = { PU3, 19 }, /* SD1_DAT1 */
> > - [RCAR_GP_PIN(3, 8)] = { PU3, 18 }, /* SD1_DAT0 */
> > - [RCAR_GP_PIN(3, 7)] = { PU3, 17 }, /* SD1_CMD */
> > - [RCAR_GP_PIN(3, 6)] = { PU3, 16 }, /* SD1_CLK */
> > - [RCAR_GP_PIN(3, 5)] = { PU3, 15 }, /* SD0_DAT3 */
> > - [RCAR_GP_PIN(3, 4)] = { PU3, 14 }, /* SD0_DAT2 */
> > - [RCAR_GP_PIN(3, 3)] = { PU3, 13 }, /* SD0_DAT1 */
> > - [RCAR_GP_PIN(3, 2)] = { PU3, 12 }, /* SD0_DAT0 */
> > - [RCAR_GP_PIN(3, 1)] = { PU3, 11 }, /* SD0_CMD */
> > - [RCAR_GP_PIN(3, 0)] = { PU3, 10 }, /* SD0_CLK */
> > -
> > - [RCAR_GP_PIN(5, 19)] = { PU4, 31 }, /* MSIOF0_SS1 */
> > - [RCAR_GP_PIN(5, 18)] = { PU4, 30 }, /* MSIOF0_SYNC */
> > - [RCAR_GP_PIN(5, 17)] = { PU4, 29 }, /* MSIOF0_SCK */
> > - [RCAR_GP_PIN(5, 16)] = { PU4, 28 }, /* HRTS0_N */
> > - [RCAR_GP_PIN(5, 15)] = { PU4, 27 }, /* HCTS0_N */
> > - [RCAR_GP_PIN(5, 14)] = { PU4, 26 }, /* HTX0 */
> > - [RCAR_GP_PIN(5, 13)] = { PU4, 25 }, /* HRX0 */
> > - [RCAR_GP_PIN(5, 12)] = { PU4, 24 }, /* HSCK0 */
> > - [RCAR_GP_PIN(5, 11)] = { PU4, 23 }, /* RX2_A */
> > - [RCAR_GP_PIN(5, 10)] = { PU4, 22 }, /* TX2_A */
> > - [RCAR_GP_PIN(5, 9)] = { PU4, 21 }, /* SCK2 */
> > - [RCAR_GP_PIN(5, 8)] = { PU4, 20 }, /* RTS1_N_TANS */
> > - [RCAR_GP_PIN(5, 7)] = { PU4, 19 }, /* CTS1_N */
> > - [RCAR_GP_PIN(5, 6)] = { PU4, 18 }, /* TX1_A */
> > - [RCAR_GP_PIN(5, 5)] = { PU4, 17 }, /* RX1_A */
> > - [RCAR_GP_PIN(5, 4)] = { PU4, 16 }, /* RTS0_N_TANS */
> > - [RCAR_GP_PIN(5, 3)] = { PU4, 15 }, /* CTS0_N */
> > - [RCAR_GP_PIN(5, 2)] = { PU4, 14 }, /* TX0 */
> > - [RCAR_GP_PIN(5, 1)] = { PU4, 13 }, /* RX0 */
> > - [RCAR_GP_PIN(5, 0)] = { PU4, 12 }, /* SCK0 */
> > - [RCAR_GP_PIN(3, 15)] = { PU4, 11 }, /* SD1_WP */
> > - [RCAR_GP_PIN(3, 14)] = { PU4, 10 }, /* SD1_CD */
> > - [RCAR_GP_PIN(3, 13)] = { PU4, 9 }, /* SD0_WP */
> > - [RCAR_GP_PIN(3, 12)] = { PU4, 8 }, /* SD0_CD */
> > - [RCAR_GP_PIN(4, 17)] = { PU4, 7 }, /* SD3_DS */
> > - [RCAR_GP_PIN(4, 16)] = { PU4, 6 }, /* SD3_DAT7 */
> > - [RCAR_GP_PIN(4, 15)] = { PU4, 5 }, /* SD3_DAT6 */
> > - [RCAR_GP_PIN(4, 14)] = { PU4, 4 }, /* SD3_DAT5 */
> > - [RCAR_GP_PIN(4, 13)] = { PU4, 3 }, /* SD3_DAT4 */
> > - [RCAR_GP_PIN(4, 12)] = { PU4, 2 }, /* SD3_DAT3 */
> > - [RCAR_GP_PIN(4, 11)] = { PU4, 1 }, /* SD3_DAT2 */
> > - [RCAR_GP_PIN(4, 10)] = { PU4, 0 }, /* SD3_DAT1 */
> > -
> > - [RCAR_GP_PIN(6, 24)] = { PU5, 31 }, /* USB0_PWEN */
> > - [RCAR_GP_PIN(6, 23)] = { PU5, 30 }, /* AUDIO_CLKB_B */
> > - [RCAR_GP_PIN(6, 22)] = { PU5, 29 }, /* AUDIO_CLKA_A */
> > - [RCAR_GP_PIN(6, 21)] = { PU5, 28 }, /* SSI_SDATA9_A */
> > - [RCAR_GP_PIN(6, 20)] = { PU5, 27 }, /* SSI_SDATA8 */
> > - [RCAR_GP_PIN(6, 19)] = { PU5, 26 }, /* SSI_SDATA7 */
> > - [RCAR_GP_PIN(6, 18)] = { PU5, 25 }, /* SSI_WS78 */
> > - [RCAR_GP_PIN(6, 17)] = { PU5, 24 }, /* SSI_SCK78 */
> > - [RCAR_GP_PIN(6, 16)] = { PU5, 23 }, /* SSI_SDATA6 */
> > - [RCAR_GP_PIN(6, 15)] = { PU5, 22 }, /* SSI_WS6 */
> > - [RCAR_GP_PIN(6, 14)] = { PU5, 21 }, /* SSI_SCK6 */
> > - [RCAR_GP_PIN(6, 13)] = { PU5, 20 }, /* SSI_SDATA5 */
> > - [RCAR_GP_PIN(6, 12)] = { PU5, 19 }, /* SSI_WS5 */
> > - [RCAR_GP_PIN(6, 11)] = { PU5, 18 }, /* SSI_SCK5 */
> > - [RCAR_GP_PIN(6, 10)] = { PU5, 17 }, /* SSI_SDATA4 */
> > - [RCAR_GP_PIN(6, 9)] = { PU5, 16 }, /* SSI_WS4 */
> > - [RCAR_GP_PIN(6, 8)] = { PU5, 15 }, /* SSI_SCK4 */
> > - [RCAR_GP_PIN(6, 7)] = { PU5, 14 }, /* SSI_SDATA3 */
> > - [RCAR_GP_PIN(6, 6)] = { PU5, 13 }, /* SSI_WS34 */
> > - [RCAR_GP_PIN(6, 5)] = { PU5, 12 }, /* SSI_SCK34 */
> > - [RCAR_GP_PIN(6, 4)] = { PU5, 11 }, /* SSI_SDATA2_A */
> > - [RCAR_GP_PIN(6, 3)] = { PU5, 10 }, /* SSI_SDATA1_A */
> > - [RCAR_GP_PIN(6, 2)] = { PU5, 9 }, /* SSI_SDATA0 */
> > - [RCAR_GP_PIN(6, 1)] = { PU5, 8 }, /* SSI_WS01239 */
> > - [RCAR_GP_PIN(6, 0)] = { PU5, 7 }, /* SSI_SCK01239 */
> > - [RCAR_GP_PIN(5, 25)] = { PU5, 5 }, /* MLB_DAT */
> > - [RCAR_GP_PIN(5, 24)] = { PU5, 4 }, /* MLB_SIG */
> > - [RCAR_GP_PIN(5, 23)] = { PU5, 3 }, /* MLB_CLK */
> > - [RCAR_GP_PIN(5, 22)] = { PU5, 2 }, /* MSIOF0_RXD */
> > - [RCAR_GP_PIN(5, 21)] = { PU5, 1 }, /* MSIOF0_SS2 */
> > - [RCAR_GP_PIN(5, 20)] = { PU5, 0 }, /* MSIOF0_TXD */
> > -
> > - [RCAR_GP_PIN(6, 31)] = { PU6, 6 }, /* USB31_OVC */
> > - [RCAR_GP_PIN(6, 30)] = { PU6, 5 }, /* USB31_PWEN */
> > - [RCAR_GP_PIN(6, 29)] = { PU6, 4 }, /* USB30_OVC */
> > - [RCAR_GP_PIN(6, 28)] = { PU6, 3 }, /* USB30_PWEN */
> > - [RCAR_GP_PIN(6, 27)] = { PU6, 2 }, /* USB1_OVC */
> > - [RCAR_GP_PIN(6, 26)] = { PU6, 1 }, /* USB1_PWEN */
> > - [RCAR_GP_PIN(6, 25)] = { PU6, 0 }, /* USB0_OVC */
> > +static const struct sh_pfc_bias_info pullups[] = {
>
> I haven't reviewed this table, I trust your regexp skills.
Geert showed me a nice way to review changes like this:
git diff --color-words
>
> > + { RCAR_GP_PIN(2, 11), PU0, 31 }, /* AVB_PHY_INT */
> > + { RCAR_GP_PIN(2, 10), PU0, 30 }, /* AVB_MAGIC */
> > + { RCAR_GP_PIN(2, 9), PU0, 29 }, /* AVB_MDC */
> > +
> > + { RCAR_GP_PIN(1, 19), PU1, 31 }, /* A19 */
> > + { RCAR_GP_PIN(1, 18), PU1, 30 }, /* A18 */
> > + { RCAR_GP_PIN(1, 17), PU1, 29 }, /* A17 */
> > + { RCAR_GP_PIN(1, 16), PU1, 28 }, /* A16 */
> > + { RCAR_GP_PIN(1, 15), PU1, 27 }, /* A15 */
> > + { RCAR_GP_PIN(1, 14), PU1, 26 }, /* A14 */
> > + { RCAR_GP_PIN(1, 13), PU1, 25 }, /* A13 */
> > + { RCAR_GP_PIN(1, 12), PU1, 24 }, /* A12 */
> > + { RCAR_GP_PIN(1, 11), PU1, 23 }, /* A11 */
> > + { RCAR_GP_PIN(1, 10), PU1, 22 }, /* A10 */
> > + { RCAR_GP_PIN(1, 9), PU1, 21 }, /* A9 */
> > + { RCAR_GP_PIN(1, 8), PU1, 20 }, /* A8 */
> > + { RCAR_GP_PIN(1, 7), PU1, 19 }, /* A7 */
> > + { RCAR_GP_PIN(1, 6), PU1, 18 }, /* A6 */
> > + { RCAR_GP_PIN(1, 5), PU1, 17 }, /* A5 */
> > + { RCAR_GP_PIN(1, 4), PU1, 16 }, /* A4 */
> > + { RCAR_GP_PIN(1, 3), PU1, 15 }, /* A3 */
> > + { RCAR_GP_PIN(1, 2), PU1, 14 }, /* A2 */
> > + { RCAR_GP_PIN(1, 1), PU1, 13 }, /* A1 */
> > + { RCAR_GP_PIN(1, 0), PU1, 12 }, /* A0 */
> > + { RCAR_GP_PIN(2, 8), PU1, 11 }, /* PWM2_A */
> > + { RCAR_GP_PIN(2, 7), PU1, 10 }, /* PWM1_A */
> > + { RCAR_GP_PIN(2, 6), PU1, 9 }, /* PWM0 */
> > + { RCAR_GP_PIN(2, 5), PU1, 8 }, /* IRQ5 */
> > + { RCAR_GP_PIN(2, 4), PU1, 7 }, /* IRQ4 */
> > + { RCAR_GP_PIN(2, 3), PU1, 6 }, /* IRQ3 */
> > + { RCAR_GP_PIN(2, 2), PU1, 5 }, /* IRQ2 */
> > + { RCAR_GP_PIN(2, 1), PU1, 4 }, /* IRQ1 */
> > + { RCAR_GP_PIN(2, 0), PU1, 3 }, /* IRQ0 */
> > + { RCAR_GP_PIN(2, 14), PU1, 2 }, /* AVB_AVTP_CAPTURE_A */
> > + { RCAR_GP_PIN(2, 13), PU1, 1 }, /* AVB_AVTP_MATCH_A */
> > + { RCAR_GP_PIN(2, 12), PU1, 0 }, /* AVB_LINK */
> > +
> > + { RCAR_GP_PIN(7, 3), PU2, 29 }, /* HDMI1_CEC */
> > + { RCAR_GP_PIN(7, 2), PU2, 28 }, /* HDMI0_CEC */
> > + { RCAR_GP_PIN(7, 1), PU2, 27 }, /* AVS2 */
> > + { RCAR_GP_PIN(7, 0), PU2, 26 }, /* AVS1 */
> > + { RCAR_GP_PIN(0, 15), PU2, 25 }, /* D15 */
> > + { RCAR_GP_PIN(0, 14), PU2, 24 }, /* D14 */
> > + { RCAR_GP_PIN(0, 13), PU2, 23 }, /* D13 */
> > + { RCAR_GP_PIN(0, 12), PU2, 22 }, /* D12 */
> > + { RCAR_GP_PIN(0, 11), PU2, 21 }, /* D11 */
> > + { RCAR_GP_PIN(0, 10), PU2, 20 }, /* D10 */
> > + { RCAR_GP_PIN(0, 9), PU2, 19 }, /* D9 */
> > + { RCAR_GP_PIN(0, 8), PU2, 18 }, /* D8 */
> > + { RCAR_GP_PIN(0, 7), PU2, 17 }, /* D7 */
> > + { RCAR_GP_PIN(0, 6), PU2, 16 }, /* D6 */
> > + { RCAR_GP_PIN(0, 5), PU2, 15 }, /* D5 */
> > + { RCAR_GP_PIN(0, 4), PU2, 14 }, /* D4 */
> > + { RCAR_GP_PIN(0, 3), PU2, 13 }, /* D3 */
> > + { RCAR_GP_PIN(0, 2), PU2, 12 }, /* D2 */
> > + { RCAR_GP_PIN(0, 1), PU2, 11 }, /* D1 */
> > + { RCAR_GP_PIN(0, 0), PU2, 10 }, /* D0 */
> > + { RCAR_GP_PIN(1, 27), PU2, 8 }, /* EX_WAIT0_A */
> > + { RCAR_GP_PIN(1, 26), PU2, 7 }, /* WE1_N */
> > + { RCAR_GP_PIN(1, 25), PU2, 6 }, /* WE0_N */
> > + { RCAR_GP_PIN(1, 24), PU2, 5 }, /* RD_WR_N */
> > + { RCAR_GP_PIN(1, 23), PU2, 4 }, /* RD_N */
> > + { RCAR_GP_PIN(1, 22), PU2, 3 }, /* BS_N */
> > + { RCAR_GP_PIN(1, 21), PU2, 2 }, /* CS1_N_A26 */
> > + { RCAR_GP_PIN(1, 20), PU2, 1 }, /* CS0_N */
> > +
> > + { RCAR_GP_PIN(4, 9), PU3, 31 }, /* SD3_DAT0 */
> > + { RCAR_GP_PIN(4, 8), PU3, 30 }, /* SD3_CMD */
> > + { RCAR_GP_PIN(4, 7), PU3, 29 }, /* SD3_CLK */
> > + { RCAR_GP_PIN(4, 6), PU3, 28 }, /* SD2_DS */
> > + { RCAR_GP_PIN(4, 5), PU3, 27 }, /* SD2_DAT3 */
> > + { RCAR_GP_PIN(4, 4), PU3, 26 }, /* SD2_DAT2 */
> > + { RCAR_GP_PIN(4, 3), PU3, 25 }, /* SD2_DAT1 */
> > + { RCAR_GP_PIN(4, 2), PU3, 24 }, /* SD2_DAT0 */
> > + { RCAR_GP_PIN(4, 1), PU3, 23 }, /* SD2_CMD */
> > + { RCAR_GP_PIN(4, 0), PU3, 22 }, /* SD2_CLK */
> > + { RCAR_GP_PIN(3, 11), PU3, 21 }, /* SD1_DAT3 */
> > + { RCAR_GP_PIN(3, 10), PU3, 20 }, /* SD1_DAT2 */
> > + { RCAR_GP_PIN(3, 9), PU3, 19 }, /* SD1_DAT1 */
> > + { RCAR_GP_PIN(3, 8), PU3, 18 }, /* SD1_DAT0 */
> > + { RCAR_GP_PIN(3, 7), PU3, 17 }, /* SD1_CMD */
> > + { RCAR_GP_PIN(3, 6), PU3, 16 }, /* SD1_CLK */
> > + { RCAR_GP_PIN(3, 5), PU3, 15 }, /* SD0_DAT3 */
> > + { RCAR_GP_PIN(3, 4), PU3, 14 }, /* SD0_DAT2 */
> > + { RCAR_GP_PIN(3, 3), PU3, 13 }, /* SD0_DAT1 */
> > + { RCAR_GP_PIN(3, 2), PU3, 12 }, /* SD0_DAT0 */
> > + { RCAR_GP_PIN(3, 1), PU3, 11 }, /* SD0_CMD */
> > + { RCAR_GP_PIN(3, 0), PU3, 10 }, /* SD0_CLK */
> > +
> > + { RCAR_GP_PIN(5, 19), PU4, 31 }, /* MSIOF0_SS1 */
> > + { RCAR_GP_PIN(5, 18), PU4, 30 }, /* MSIOF0_SYNC */
> > + { RCAR_GP_PIN(5, 17), PU4, 29 }, /* MSIOF0_SCK */
> > + { RCAR_GP_PIN(5, 16), PU4, 28 }, /* HRTS0_N */
> > + { RCAR_GP_PIN(5, 15), PU4, 27 }, /* HCTS0_N */
> > + { RCAR_GP_PIN(5, 14), PU4, 26 }, /* HTX0 */
> > + { RCAR_GP_PIN(5, 13), PU4, 25 }, /* HRX0 */
> > + { RCAR_GP_PIN(5, 12), PU4, 24 }, /* HSCK0 */
> > + { RCAR_GP_PIN(5, 11), PU4, 23 }, /* RX2_A */
> > + { RCAR_GP_PIN(5, 10), PU4, 22 }, /* TX2_A */
> > + { RCAR_GP_PIN(5, 9), PU4, 21 }, /* SCK2 */
> > + { RCAR_GP_PIN(5, 8), PU4, 20 }, /* RTS1_N_TANS */
> > + { RCAR_GP_PIN(5, 7), PU4, 19 }, /* CTS1_N */
> > + { RCAR_GP_PIN(5, 6), PU4, 18 }, /* TX1_A */
> > + { RCAR_GP_PIN(5, 5), PU4, 17 }, /* RX1_A */
> > + { RCAR_GP_PIN(5, 4), PU4, 16 }, /* RTS0_N_TANS */
> > + { RCAR_GP_PIN(5, 3), PU4, 15 }, /* CTS0_N */
> > + { RCAR_GP_PIN(5, 2), PU4, 14 }, /* TX0 */
> > + { RCAR_GP_PIN(5, 1), PU4, 13 }, /* RX0 */
> > + { RCAR_GP_PIN(5, 0), PU4, 12 }, /* SCK0 */
> > + { RCAR_GP_PIN(3, 15), PU4, 11 }, /* SD1_WP */
> > + { RCAR_GP_PIN(3, 14), PU4, 10 }, /* SD1_CD */
> > + { RCAR_GP_PIN(3, 13), PU4, 9 }, /* SD0_WP */
> > + { RCAR_GP_PIN(3, 12), PU4, 8 }, /* SD0_CD */
> > + { RCAR_GP_PIN(4, 17), PU4, 7 }, /* SD3_DS */
> > + { RCAR_GP_PIN(4, 16), PU4, 6 }, /* SD3_DAT7 */
> > + { RCAR_GP_PIN(4, 15), PU4, 5 }, /* SD3_DAT6 */
> > + { RCAR_GP_PIN(4, 14), PU4, 4 }, /* SD3_DAT5 */
> > + { RCAR_GP_PIN(4, 13), PU4, 3 }, /* SD3_DAT4 */
> > + { RCAR_GP_PIN(4, 12), PU4, 2 }, /* SD3_DAT3 */
> > + { RCAR_GP_PIN(4, 11), PU4, 1 }, /* SD3_DAT2 */
> > + { RCAR_GP_PIN(4, 10), PU4, 0 }, /* SD3_DAT1 */
> > +
> > + { RCAR_GP_PIN(6, 24), PU5, 31 }, /* USB0_PWEN */
> > + { RCAR_GP_PIN(6, 23), PU5, 30 }, /* AUDIO_CLKB_B */
> > + { RCAR_GP_PIN(6, 22), PU5, 29 }, /* AUDIO_CLKA_A */
> > + { RCAR_GP_PIN(6, 21), PU5, 28 }, /* SSI_SDATA9_A */
> > + { RCAR_GP_PIN(6, 20), PU5, 27 }, /* SSI_SDATA8 */
> > + { RCAR_GP_PIN(6, 19), PU5, 26 }, /* SSI_SDATA7 */
> > + { RCAR_GP_PIN(6, 18), PU5, 25 }, /* SSI_WS78 */
> > + { RCAR_GP_PIN(6, 17), PU5, 24 }, /* SSI_SCK78 */
> > + { RCAR_GP_PIN(6, 16), PU5, 23 }, /* SSI_SDATA6 */
> > + { RCAR_GP_PIN(6, 15), PU5, 22 }, /* SSI_WS6 */
> > + { RCAR_GP_PIN(6, 14), PU5, 21 }, /* SSI_SCK6 */
> > + { RCAR_GP_PIN(6, 13), PU5, 20 }, /* SSI_SDATA5 */
> > + { RCAR_GP_PIN(6, 12), PU5, 19 }, /* SSI_WS5 */
> > + { RCAR_GP_PIN(6, 11), PU5, 18 }, /* SSI_SCK5 */
> > + { RCAR_GP_PIN(6, 10), PU5, 17 }, /* SSI_SDATA4 */
> > + { RCAR_GP_PIN(6, 9), PU5, 16 }, /* SSI_WS4 */
> > + { RCAR_GP_PIN(6, 8), PU5, 15 }, /* SSI_SCK4 */
> > + { RCAR_GP_PIN(6, 7), PU5, 14 }, /* SSI_SDATA3 */
> > + { RCAR_GP_PIN(6, 6), PU5, 13 }, /* SSI_WS34 */
> > + { RCAR_GP_PIN(6, 5), PU5, 12 }, /* SSI_SCK34 */
> > + { RCAR_GP_PIN(6, 4), PU5, 11 }, /* SSI_SDATA2_A */
> > + { RCAR_GP_PIN(6, 3), PU5, 10 }, /* SSI_SDATA1_A */
> > + { RCAR_GP_PIN(6, 2), PU5, 9 }, /* SSI_SDATA0 */
> > + { RCAR_GP_PIN(6, 1), PU5, 8 }, /* SSI_WS01239 */
> > + { RCAR_GP_PIN(6, 0), PU5, 7 }, /* SSI_SCK01239 */
> > + { RCAR_GP_PIN(5, 25), PU5, 5 }, /* MLB_DAT */
> > + { RCAR_GP_PIN(5, 24), PU5, 4 }, /* MLB_SIG */
> > + { RCAR_GP_PIN(5, 23), PU5, 3 }, /* MLB_CLK */
> > + { RCAR_GP_PIN(5, 22), PU5, 2 }, /* MSIOF0_RXD */
> > + { RCAR_GP_PIN(5, 21), PU5, 1 }, /* MSIOF0_SS2 */
> > + { RCAR_GP_PIN(5, 20), PU5, 0 }, /* MSIOF0_TXD */
> > +
> > + { RCAR_GP_PIN(6, 31), PU6, 6 }, /* USB31_OVC */
> > + { RCAR_GP_PIN(6, 30), PU6, 5 }, /* USB31_PWEN */
> > + { RCAR_GP_PIN(6, 29), PU6, 4 }, /* USB30_OVC */
> > + { RCAR_GP_PIN(6, 28), PU6, 3 }, /* USB30_PWEN */
> > + { RCAR_GP_PIN(6, 27), PU6, 2 }, /* USB1_OVC */
> > + { RCAR_GP_PIN(6, 26), PU6, 1 }, /* USB1_PWEN */
> > + { RCAR_GP_PIN(6, 25), PU6, 0 }, /* USB0_OVC */
> > };
> >
> > static unsigned int r8a7795_pinmux_get_bias(struct sh_pfc *pfc,
> > @@ -5360,12 +5357,13 @@ static unsigned int r8a7795_pinmux_get_bias(struct
> > sh_pfc *pfc, {
> > u32 reg;
> > u32 bit;
> > + struct sh_pfc_bias_info info;
>
> Nitpicking, why am I the only one to find the code more readable when
> long variable declarations come before short ones ? :-)
I too find it more readable when longer variables come before short
ones, but in situations like this one where reg and bit are of the same
type but declared on two consecutive lines I get side tracked starring
at that trying to figure out why, also reg and bit are not declared in
alphabetical order... :-)
I will settle on the middle ground here and sort my line length as done
in 5/6 since a new iteration of this series are needed anyhow.
>
> >
> > - if (WARN_ON_ONCE(!pullups[pin].reg))
> > + if (sh_pfc_pin_to_bias_info(pullups, ARRAY_SIZE(pullups), pin, &info))
> > return PIN_CONFIG_BIAS_DISABLE;
>
> The implementation will change slightly if you follow my advice regarding
> patch 2/6.
>
> The same comments apply to the set_bias function below too, and to patch 5/6
> in this series (except for the variable declaration ordering that you got
> right there :-)).
>
> Apart from that, for 4/6 and 5/6,
>
> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Thank you, I will follow your advice in 2/6.
>
> >
> > - reg = pullups[pin].reg;
> > - bit = BIT(pullups[pin].bit);
> > + reg = info.reg;
> > + bit = BIT(info.bit);
> >
> > if (!(sh_pfc_read_reg(pfc, PUEN + reg, 32) & bit))
> > return PIN_CONFIG_BIAS_DISABLE;
> > @@ -5381,12 +5379,13 @@ static void r8a7795_pinmux_set_bias(struct sh_pfc
> > *pfc, unsigned int pin, u32 enable, updown;
> > u32 reg;
> > u32 bit;
> > + struct sh_pfc_bias_info info;
> >
> > - if (WARN_ON_ONCE(!pullups[pin].reg))
> > + if (sh_pfc_pin_to_bias_info(pullups, ARRAY_SIZE(pullups), pin, &info))
> > return;
> >
> > - reg = pullups[pin].reg;
> > - bit = BIT(pullups[pin].bit);
> > + reg = info.reg;
> > + bit = BIT(info.bit);
> >
> > enable = sh_pfc_read_reg(pfc, PUEN + reg, 32) & ~bit;
> > if (bias != PIN_CONFIG_BIAS_DISABLE)
--
Regards,
Niklas Söderlund
next prev parent reply other threads:[~2016-11-12 13:44 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-11-11 20:30 [PATCHv2 0/6] pinctrl: sh-pfc: Fixups for bias handling and preparation for none GPIO pins Niklas Söderlund
2016-11-11 20:30 ` [PATCHv2 1/6] pinctrl: sh-pfc: Do not unconditionally support PIN_CONFIG_BIAS_DISABLE Niklas Söderlund
2016-11-11 20:30 ` [PATCHv2 2/6] pinctrl: sh-pfc: Add helper to handle bias lookup table Niklas Söderlund
2016-11-12 1:46 ` Laurent Pinchart
2016-11-12 13:41 ` Niklas Söderlund
2016-11-11 20:30 ` [PATCHv2 3/6] pinctrl: sh-pfc: r8a7795: Simplify get bias logic Niklas Söderlund
2016-11-11 22:42 ` Laurent Pinchart
2016-11-11 20:30 ` [PATCHv2 4/6] pinctrl: sh-pfc: r8a7795: Use lookup function for bias data Niklas Söderlund
2016-11-12 1:47 ` Laurent Pinchart
2016-11-12 13:44 ` Niklas Söderlund [this message]
2016-11-11 20:30 ` [PATCHv2 5/6] pinctrl: sh-pfc: r8a7778: " Niklas Söderlund
2016-11-11 20:30 ` [PATCHv2 6/6] pinctrl: sh-pfc: Support named pins with custom configuration Niklas Söderlund
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20161112134441.GD3834@bigcity.dyn.berto.se \
--to=niklas.soderlund@ragnatech.se \
--cc=geert+renesas@glider.be \
--cc=laurent.pinchart@ideasonboard.com \
--cc=linus.walleij@linaro.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-renesas-soc@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).