Re: [PATCH v4 3/9] dt-bindings: pinctrl: Add RZ/A1 bindings doc

[jmondi <jacopo-AW8dsiIh9cEdnm+yROfE0A@public.gmane.org>]

Hi Rob,

On Mon, Apr 10, 2017 at 01:12:15PM -0500, Rob Herring wrote:
> On Wed, Apr 05, 2017 at 04:07:21PM +0200, Jacopo Mondi wrote:
> > Add device tree bindings documentation for Renesas RZ/A1 gpio and pin
> > controller.
> >
> > Signed-off-by: Jacopo Mondi <jacopo+renesas-AW8dsiIh9cEdnm+yROfE0A@public.gmane.org>
> > ---
> >  .../bindings/pinctrl/renesas,rza1-pinctrl.txt      | 218 +++++++++++++++++++++
> >  1 file changed, 218 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/pinctrl/renesas,rza1-pinctrl.txt
> >
> > diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,rza1-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,rza1-pinctrl.txt
> > new file mode 100644
> > index 0000000..46584ef
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/pinctrl/renesas,rza1-pinctrl.txt
> > @@ -0,0 +1,218 @@
> > +Renesas RZ/A1 combined Pin and GPIO controller
> > +
> > +The Renesas SoCs of RZ/A1 family feature a combined Pin and GPIO controller,
> > +named "Ports" in the hardware reference manual.
> > +Pin multiplexing and GPIO configuration is performed on a per-pin basis
> > +writing configuration values to per-port register sets.
> > +Each "port" features up to 16 pins, each of them configurable for GPIO
> > +function (port mode) or in alternate function mode.
> > +Up to 8 different alternate function modes exist for each single pin.
> > +
> > +Pin controller node
> > +-------------------
> > +
> > +Required properties:
> > +  - compatible
> > +    this shall be "renesas,r7s72100-ports".
> > +
> > +  - reg
> > +    address base and length of the memory area where pin controller
> > +    hardware is mapped to.
> > +
> > +Example:
> > +Pin controller node for RZ/A1H SoC (r7s72100)
> > +
> > +pinctrl: pin-controller@fcfe3000 {
> > +	compatible = "renesas,r7s72100-ports";
> > +
> > +	reg = <0xfcfe3000 0x4230>;
> > +};
> > +
> > +Sub-nodes
> > +---------
> > +
> > +The child nodes of the pin controller node describe a pin multiplexing
> > +function or a gpio controller alternatively.
> > +
> > +- Pin multiplexing sub-nodes:
> > +  A pin multiplexing sub-node describes how to configure a set of
> > +  (or a single) pin in some desired alternate function mode.
> > +  A single sub-node may define several pin configurations.
> > +  Some alternate functions require special pin configuration flags to be
> > +  supplied along with the alternate function configuration number.
> > +  When hardware reference manual specifies a pin function to be either
> > +  "bi-directional" or "software IO driven", use the generic properties from
> > +  <include/linux/pinctrl/pinconf_generic.h> header file to instruct the
> > +  pin controller to perform the desired pin configuration operations.
> > +  Please refer to pinctrl-bindings.txt to get to know more on generic
> > +  pin properties usage.
> > +
> > +  The allowed generic formats for a pin multiplexing sub-node are the
> > +  following ones:
> > +
> > +  node-1 {
> > +      pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ;
> > +      GENERIC_PINCONFIG;
>
> What's GENERIC_PINCONFIG? I see this in some other binding docs, but not
> used anywhere. If this is a boolean property then get rid of the all
> caps. If this is a define, then don't use complex defines that expand to
> dts source.

GENERIC_PINCONF is a wildcard that identifies "generic" pin
configuration properties the pin controller framework defines.

Have a look at "enum pin_config_param" in
<include/linux/pinctrl/pinconf-generic.h>

Thanks
  j
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html