[PATCH AUTOSEL 5.2 18/70] pinctrl: stmfx: update pinconf settings

[PATCH AUTOSEL 5.2 18/70] pinctrl: stmfx: update pinconf settings

[Sasha Levin]

From: Alexandre Torgue <alexandre.torgue@st.com>

[ Upstream commit a502b343ebd0eab38f3cb33fbb84011847cf5aac ]

According to the following tab (coming from STMFX datasheet), updates
have to done in stmfx_pinconf_set function:

-"type" has to be set when "bias" is configured as "pull-up or pull-down"
-PIN_CONFIG_DRIVE_PUSH_PULL should only be used when gpio is configured as
 output. There is so no need to check direction.

DIR | TYPE | PUPD | MFX GPIO configuration
----|------|------|---------------------------------------------------
1   | 1    | 1    | OUTPUT open drain with internal pull-up resistor
----|------|------|---------------------------------------------------
1   | 1    | 0    | OUTPUT open drain with internal pull-down resistor
----|------|------|---------------------------------------------------
1   | 0    | 0/1  | OUTPUT push pull no pull
----|------|------|---------------------------------------------------
0   | 1    | 1    | INPUT with internal pull-up resistor
----|------|------|---------------------------------------------------
0   | 1    | 0    | INPUT with internal pull-down resistor
----|------|------|---------------------------------------------------
0   | 0    | 1    | INPUT floating
----|------|------|---------------------------------------------------
0   | 0    | 0    | analog (GPIO not used, default setting)

Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/1564053416-32192-1-git-send-email-amelie.delaunay@st.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pinctrl/pinctrl-stmfx.c | 24 ++++++++++++------------
 1 file changed, 12 insertions(+), 12 deletions(-)

diff --git a/drivers/pinctrl/pinctrl-stmfx.c b/drivers/pinctrl/pinctrl-stmfx.c
index eba872ce4a7cb..c82ad4b629e3e 100644
--- a/drivers/pinctrl/pinctrl-stmfx.c
+++ b/drivers/pinctrl/pinctrl-stmfx.c
@@ -296,29 +296,29 @@ static int stmfx_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
 		switch (param) {
 		case PIN_CONFIG_BIAS_PULL_PIN_DEFAULT:
 		case PIN_CONFIG_BIAS_DISABLE:
+		case PIN_CONFIG_DRIVE_PUSH_PULL:
+			ret = stmfx_pinconf_set_type(pctl, pin, 0);
+			if (ret)
+				return ret;
+			break;
 		case PIN_CONFIG_BIAS_PULL_DOWN:
+			ret = stmfx_pinconf_set_type(pctl, pin, 1);
+			if (ret)
+				return ret;
 			ret = stmfx_pinconf_set_pupd(pctl, pin, 0);
 			if (ret)
 				return ret;
 			break;
 		case PIN_CONFIG_BIAS_PULL_UP:
-			ret = stmfx_pinconf_set_pupd(pctl, pin, 1);
+			ret = stmfx_pinconf_set_type(pctl, pin, 1);
 			if (ret)
 				return ret;
-			break;
-		case PIN_CONFIG_DRIVE_OPEN_DRAIN:
-			if (!dir)
-				ret = stmfx_pinconf_set_type(pctl, pin, 1);
-			else
-				ret = stmfx_pinconf_set_type(pctl, pin, 0);
+			ret = stmfx_pinconf_set_pupd(pctl, pin, 1);
 			if (ret)
 				return ret;
 			break;
-		case PIN_CONFIG_DRIVE_PUSH_PULL:
-			if (!dir)
-				ret = stmfx_pinconf_set_type(pctl, pin, 0);
-			else
-				ret = stmfx_pinconf_set_type(pctl, pin, 1);
+		case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+			ret = stmfx_pinconf_set_type(pctl, pin, 1);
 			if (ret)
 				return ret;
 			break;
-- 
2.20.1

[PATCH AUTOSEL 5.2 39/70] pinctrl: tegra: Fix write barrier placement in pmx_writel

[Sasha Levin]

From: Sowjanya Komatineni <skomatineni@nvidia.com>

[ Upstream commit c2cf351eba2ff6002ce8eb178452219d2521e38e ]

pmx_writel uses writel which inserts write barrier before the
register write.

This patch has fix to replace writel with writel_relaxed followed
by a readback and memory barrier to ensure write operation is
completed for successful pinctrl change.

Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1565984527-5272-2-git-send-email-skomatineni@nvidia.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pinctrl/tegra/pinctrl-tegra.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/pinctrl/tegra/pinctrl-tegra.c b/drivers/pinctrl/tegra/pinctrl-tegra.c
index abcfbad94f00e..849c3b34e887c 100644
--- a/drivers/pinctrl/tegra/pinctrl-tegra.c
+++ b/drivers/pinctrl/tegra/pinctrl-tegra.c
@@ -32,7 +32,9 @@ static inline u32 pmx_readl(struct tegra_pmx *pmx, u32 bank, u32 reg)
 
 static inline void pmx_writel(struct tegra_pmx *pmx, u32 val, u32 bank, u32 reg)
 {
-	writel(val, pmx->regs[bank] + reg);
+	writel_relaxed(val, pmx->regs[bank] + reg);
+	/* make sure pinmux register write completed */
+	pmx_readl(pmx, bank, reg);
 }
 
 static int tegra_pinctrl_get_groups_count(struct pinctrl_dev *pctldev)
-- 
2.20.1

[PATCH AUTOSEL 5.2 44/70] pinctrl: amd: disable spurious-firing GPIO IRQs

[Sasha Levin]

From: Daniel Drake <drake@endlessm.com>

[ Upstream commit d21b8adbd475dba19ac2086d3306327b4a297418 ]

When cold-booting Asus X434DA, GPIO 7 is found to be already configured
as an interrupt, and the GPIO level is found to be in a state that
causes the interrupt to fire.

As soon as pinctrl-amd probes, this interrupt fires and invokes
amd_gpio_irq_handler(). The IRQ is acked, but no GPIO-IRQ handler was
invoked, so the GPIO level being unchanged just causes another interrupt
to fire again immediately after.

This results in an interrupt storm causing this platform to hang
during boot, right after pinctrl-amd is probed.

Detect this situation and disable the GPIO interrupt when this happens.
This enables the affected platform to boot as normal. GPIO 7 actually is
the I2C touchpad interrupt line, and later on, i2c-multitouch loads and
re-enables this interrupt when it is ready to handle it.

Instead of this approach, I considered disabling all GPIO interrupts at
probe time, however that seems a little risky, and I also confirmed that
Windows does not seem to have this behaviour: the same 41 GPIO IRQs are
enabled under both Linux and Windows, which is a far larger collection
than the GPIOs referenced by the DSDT on this platform.

Signed-off-by: Daniel Drake <drake@endlessm.com>
Link: https://lore.kernel.org/r/20190814090540.7152-1-drake@endlessm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pinctrl/pinctrl-amd.c | 12 +++++++++++-
 1 file changed, 11 insertions(+), 1 deletion(-)

diff --git a/drivers/pinctrl/pinctrl-amd.c b/drivers/pinctrl/pinctrl-amd.c
index 9b9c61e3f0652..977792654e017 100644
--- a/drivers/pinctrl/pinctrl-amd.c
+++ b/drivers/pinctrl/pinctrl-amd.c
@@ -565,15 +565,25 @@ static irqreturn_t amd_gpio_irq_handler(int irq, void *dev_id)
 			    !(regval & BIT(INTERRUPT_MASK_OFF)))
 				continue;
 			irq = irq_find_mapping(gc->irq.domain, irqnr + i);
-			generic_handle_irq(irq);
+			if (irq != 0)
+				generic_handle_irq(irq);
 
 			/* Clear interrupt.
 			 * We must read the pin register again, in case the
 			 * value was changed while executing
 			 * generic_handle_irq() above.
+			 * If we didn't find a mapping for the interrupt,
+			 * disable it in order to avoid a system hang caused
+			 * by an interrupt storm.
 			 */
 			raw_spin_lock_irqsave(&gpio_dev->lock, flags);
 			regval = readl(regs + i);
+			if (irq == 0) {
+				regval &= ~BIT(INTERRUPT_ENABLE_OFF);
+				dev_dbg(&gpio_dev->pdev->dev,
+					"Disabling spurious GPIO IRQ %d\n",
+					irqnr + i);
+			}
 			writel(regval, regs + i);
 			raw_spin_unlock_irqrestore(&gpio_dev->lock, flags);
 			ret = IRQ_HANDLED;
-- 
2.20.1

[PATCH AUTOSEL 5.2 56/70] pinctrl: meson-gxbb: Fix wrong pinning definition for uart_c

[Sasha Levin]

From: Otto Meier <gf435@gmx.net>

[ Upstream commit cb0438e4436085d89706b5ccfce4d5da531253de ]

Hi i tried to use the uart_C of the the odroid-c2.

I enabled it in the dts file. During boot it crashed when the
the sdcard slot is addressed.

After long search in the net i found this:

https://forum.odroid.com/viewtopic.php?f=139&t=25371&p=194370&hilit=uart_C#p177856

After changing the pin definitions accordingly erverything works.
Uart_c is functioning and sdcard ist working.

Fixes: 6db0f3a8a04e46 ("pinctrl: amlogic: gxbb: add more UART pins")
Signed-off-by: Otto Meier <gf435@gmx.net>
Link: https://lore.kernel.org/r/1cc32a18-464d-5531-7a1c-084390e2ecb1@gmx.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pinctrl/meson/pinctrl-meson-gxbb.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/drivers/pinctrl/meson/pinctrl-meson-gxbb.c b/drivers/pinctrl/meson/pinctrl-meson-gxbb.c
index 6c640837073ef..5bfa56f3847ef 100644
--- a/drivers/pinctrl/meson/pinctrl-meson-gxbb.c
+++ b/drivers/pinctrl/meson/pinctrl-meson-gxbb.c
@@ -192,8 +192,8 @@ static const unsigned int uart_rts_b_pins[]	= { GPIODV_27 };
 
 static const unsigned int uart_tx_c_pins[]	= { GPIOY_13 };
 static const unsigned int uart_rx_c_pins[]	= { GPIOY_14 };
-static const unsigned int uart_cts_c_pins[]	= { GPIOX_11 };
-static const unsigned int uart_rts_c_pins[]	= { GPIOX_12 };
+static const unsigned int uart_cts_c_pins[]	= { GPIOY_11 };
+static const unsigned int uart_rts_c_pins[]	= { GPIOY_12 };
 
 static const unsigned int i2c_sck_a_pins[]	= { GPIODV_25 };
 static const unsigned int i2c_sda_a_pins[]	= { GPIODV_24 };
@@ -439,10 +439,10 @@ static struct meson_pmx_group meson_gxbb_periphs_groups[] = {
 	GROUP(pwm_f_x,		3,	18),
 
 	/* Bank Y */
-	GROUP(uart_cts_c,	1,	19),
-	GROUP(uart_rts_c,	1,	18),
-	GROUP(uart_tx_c,	1,	17),
-	GROUP(uart_rx_c,	1,	16),
+	GROUP(uart_cts_c,	1,	17),
+	GROUP(uart_rts_c,	1,	16),
+	GROUP(uart_tx_c,	1,	19),
+	GROUP(uart_rx_c,	1,	18),
 	GROUP(pwm_a_y,		1,	21),
 	GROUP(pwm_f_y,		1,	20),
 	GROUP(i2s_out_ch23_y,	1,	5),
-- 
2.20.1