From: Kent Gibson <warthog618@gmail.com>
To: linux-gpio@vger.kernel.org, brgl@bgdev.pl,
linus.walleij@linaro.org, bamv2005@gmail.com
Cc: drew@pdp7.com, Kent Gibson <warthog618@gmail.com>
Subject: [PATCH 5/5] gpiolib: allow pull up/down on outputs
Date: Fri, 11 Oct 2019 23:46:50 +0800 [thread overview]
Message-ID: <20191011154650.1749-6-warthog618@gmail.com> (raw)
In-Reply-To: <20191011154650.1749-1-warthog618@gmail.com>
This patch allows pull up/down bias to be set on outputs.
Use case is for open source or open drain applications where
internal pull up/down may conflict with external biasing.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
---
drivers/gpio/gpiolib.c | 35 +++++++++++++++++++++++------------
1 file changed, 23 insertions(+), 12 deletions(-)
diff --git a/drivers/gpio/gpiolib.c b/drivers/gpio/gpiolib.c
index f0665ea396cd..38ead7a87d44 100644
--- a/drivers/gpio/gpiolib.c
+++ b/drivers/gpio/gpiolib.c
@@ -554,8 +554,9 @@ static int linehandle_create(struct gpio_device *gdev, void __user *ip)
(lflags & GPIOHANDLE_REQUEST_OPEN_SOURCE)))
return -EINVAL;
- /* PULL_UP and PULL_DOWN flags only make sense for input mode. */
- if (!(lflags & GPIOHANDLE_REQUEST_INPUT) &&
+ /* PULL_UP and PULL_DOWN flags only allowed for input or output mode. */
+ if (!((lflags & GPIOHANDLE_REQUEST_INPUT) ||
+ (lflags & GPIOHANDLE_REQUEST_OUTPUT)) &&
((lflags & GPIOHANDLE_REQUEST_PULL_UP) ||
(lflags & GPIOHANDLE_REQUEST_PULL_DOWN)))
return -EINVAL;
@@ -2932,6 +2933,24 @@ static int gpio_set_config(struct gpio_chip *gc, unsigned offset,
return gc->set_config ? gc->set_config(gc, offset, config) : -ENOTSUPP;
}
+static int gpio_set_bias(struct gpio_chip *chip, struct gpio_desc *desc)
+{
+ int bias = 0;
+
+ if (test_bit(FLAG_PULL_UP, &desc->flags) &&
+ test_bit(FLAG_PULL_DOWN, &desc->flags))
+ bias = PIN_CONFIG_BIAS_DISABLE;
+ else if (test_bit(FLAG_PULL_UP, &desc->flags))
+ bias = PIN_CONFIG_BIAS_PULL_UP;
+ else if (test_bit(FLAG_PULL_DOWN, &desc->flags))
+ bias = PIN_CONFIG_BIAS_PULL_DOWN;
+
+ if (bias)
+ return gpio_set_config(chip, gpio_chip_hwgpio(desc), bias);
+
+ return 0;
+}
+
/**
* gpiod_direction_input - set the GPIO direction to input
* @desc: GPIO to set to input
@@ -2979,16 +2998,7 @@ int gpiod_direction_input(struct gpio_desc *desc)
if (ret == 0)
clear_bit(FLAG_IS_OUT, &desc->flags);
- if (test_bit(FLAG_PULL_UP, &desc->flags) &&
- test_bit(FLAG_PULL_DOWN, &desc->flags))
- gpio_set_config(chip, gpio_chip_hwgpio(desc),
- PIN_CONFIG_BIAS_DISABLE);
- else if (test_bit(FLAG_PULL_UP, &desc->flags))
- gpio_set_config(chip, gpio_chip_hwgpio(desc),
- PIN_CONFIG_BIAS_PULL_UP);
- else if (test_bit(FLAG_PULL_DOWN, &desc->flags))
- gpio_set_config(chip, gpio_chip_hwgpio(desc),
- PIN_CONFIG_BIAS_PULL_DOWN);
+ gpio_set_bias(chip, desc);
trace_gpio_direction(desc_to_gpio(desc), 1, ret);
@@ -3114,6 +3124,7 @@ int gpiod_direction_output(struct gpio_desc *desc, int value)
}
set_output_value:
+ gpio_set_bias(gc, desc);
return gpiod_direction_output_raw_commit(desc, value);
}
EXPORT_SYMBOL_GPL(gpiod_direction_output);
--
2.23.0
next prev parent reply other threads:[~2019-10-11 15:48 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-10-11 15:46 [PATCH 0/5] gpio: expose pull-up/pull-down line flags to userspace Kent Gibson
2019-10-11 15:46 ` [PATCH 1/5] gpiolib: add support for pull up/down to lineevent_create Kent Gibson
2019-10-11 15:46 ` [PATCH 2/5] gpio: mockup: add set_config to support pull up/down Kent Gibson
2019-10-11 15:46 ` [PATCH 3/5] gpiolib: pull requires explicit input mode Kent Gibson
2019-10-11 15:46 ` [PATCH 4/5] gpiolib: disable bias on inputs when pull up/down are both set Kent Gibson
2019-10-11 15:46 ` Kent Gibson [this message]
2019-10-11 17:51 ` [PATCH 0/5] gpio: expose pull-up/pull-down line flags to userspace Bartosz Golaszewski
2019-10-12 0:53 ` Kent Gibson
2019-10-12 5:52 ` Bartosz Golaszewski
2019-10-16 11:52 ` Linus Walleij
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20191011154650.1749-6-warthog618@gmail.com \
--to=warthog618@gmail.com \
--cc=bamv2005@gmail.com \
--cc=brgl@bgdev.pl \
--cc=drew@pdp7.com \
--cc=linus.walleij@linaro.org \
--cc=linux-gpio@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).