* [PATCH 0/4] Add GPIO support for RDA8810PL SoC
@ 2019-10-13 11:40 Manivannan Sadhasivam
2019-10-13 11:40 ` [PATCH 1/4] dt-bindings: gpio: Add devicetree binding for RDA Micro GPIO controller Manivannan Sadhasivam
` (3 more replies)
0 siblings, 4 replies; 7+ messages in thread
From: Manivannan Sadhasivam @ 2019-10-13 11:40 UTC (permalink / raw)
To: linus.walleij, bgolaszewski
Cc: linux-arm-kernel, linux-unisoc, linux-gpio, linux-kernel,
orsonzhai, Manivannan Sadhasivam
Hello,
This patchset adds GPIO controller support for RDA Micro RDA8810PL
SoC. This SoC has 4 GPIO controllers and each handles 32 GPIOs. Except
GPIOC, all controllers are capable of generating edge/level interrupts
from first 8 GPIO lines. The pinctrl part for this SoC will be added
later.
This driver has been validated on 96Boards OrangePi i96 board from
Shenzhen Xunlong Software Co.,Limited with libgpiod.
Thanks,
Mani
Manivannan Sadhasivam (4):
dt-bindings: gpio: Add devicetree binding for RDA Micro GPIO
controller
gpio: Add RDA Micro GPIO controller support
ARM: dts: Add RDA8810PL GPIO controllers
MAINTAINERS: Add entry for RDA Micro GPIO driver and binding
.../devicetree/bindings/gpio/gpio-rda.yaml | 50 +++
MAINTAINERS | 2 +
arch/arm/boot/dts/rda8810pl.dtsi | 48 +++
drivers/gpio/Kconfig | 8 +
drivers/gpio/Makefile | 1 +
drivers/gpio/gpio-rda.c | 334 ++++++++++++++++++
6 files changed, 443 insertions(+)
create mode 100644 Documentation/devicetree/bindings/gpio/gpio-rda.yaml
create mode 100644 drivers/gpio/gpio-rda.c
--
2.17.1
^ permalink raw reply [flat|nested] 7+ messages in thread* [PATCH 1/4] dt-bindings: gpio: Add devicetree binding for RDA Micro GPIO controller 2019-10-13 11:40 [PATCH 0/4] Add GPIO support for RDA8810PL SoC Manivannan Sadhasivam @ 2019-10-13 11:40 ` Manivannan Sadhasivam 2019-10-13 11:40 ` [PATCH 2/4] gpio: Add RDA Micro GPIO controller support Manivannan Sadhasivam ` (2 subsequent siblings) 3 siblings, 0 replies; 7+ messages in thread From: Manivannan Sadhasivam @ 2019-10-13 11:40 UTC (permalink / raw) To: linus.walleij, bgolaszewski Cc: linux-arm-kernel, linux-unisoc, linux-gpio, linux-kernel, orsonzhai, Manivannan Sadhasivam Add YAML devicetree binding for RDA Micro GPIO controller. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> --- .../devicetree/bindings/gpio/gpio-rda.yaml | 50 +++++++++++++++++++ 1 file changed, 50 insertions(+) create mode 100644 Documentation/devicetree/bindings/gpio/gpio-rda.yaml diff --git a/Documentation/devicetree/bindings/gpio/gpio-rda.yaml b/Documentation/devicetree/bindings/gpio/gpio-rda.yaml new file mode 100644 index 000000000000..6ece555f074f --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-rda.yaml @@ -0,0 +1,50 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/gpio-rda.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: RDA Micro GPIO controller + +maintainers: + - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> + +properties: + compatible: + const: rda,8810pl-gpio + + reg: + maxItems: 1 + + gpio-controller: true + + "#gpio-cells": + const: 2 + + ngpios: + description: + Number of available gpios in a bank. + minimum: 1 + maximum: 32 + + interrupt-controller: true + + "#interrupt-cells": + const: 2 + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + - gpio-controller + - "#gpio-cells" + - ngpios + - interrupt-controller + - "#interrupt-cells" + - interrupts + +additionalProperties: false + +... -- 2.17.1 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH 2/4] gpio: Add RDA Micro GPIO controller support 2019-10-13 11:40 [PATCH 0/4] Add GPIO support for RDA8810PL SoC Manivannan Sadhasivam 2019-10-13 11:40 ` [PATCH 1/4] dt-bindings: gpio: Add devicetree binding for RDA Micro GPIO controller Manivannan Sadhasivam @ 2019-10-13 11:40 ` Manivannan Sadhasivam 2019-10-14 14:25 ` Bartosz Golaszewski 2019-10-13 11:40 ` [PATCH 3/4] ARM: dts: Add RDA8810PL GPIO controllers Manivannan Sadhasivam 2019-10-13 11:40 ` [PATCH 4/4] MAINTAINERS: Add entry for RDA Micro GPIO driver and binding Manivannan Sadhasivam 3 siblings, 1 reply; 7+ messages in thread From: Manivannan Sadhasivam @ 2019-10-13 11:40 UTC (permalink / raw) To: linus.walleij, bgolaszewski Cc: linux-arm-kernel, linux-unisoc, linux-gpio, linux-kernel, orsonzhai, Manivannan Sadhasivam Add support for GPIO controller from RDA Micro. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> --- drivers/gpio/Kconfig | 8 + drivers/gpio/Makefile | 1 + drivers/gpio/gpio-rda.c | 334 ++++++++++++++++++++++++++++++++++++++++ 3 files changed, 343 insertions(+) create mode 100644 drivers/gpio/gpio-rda.c diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig index 38e096e6925f..71826e61fdb3 100644 --- a/drivers/gpio/Kconfig +++ b/drivers/gpio/Kconfig @@ -435,6 +435,14 @@ config GPIO_RCAR help Say yes here to support GPIO on Renesas R-Car SoCs. +config GPIO_RDA + bool "RDA Micro GPIO controller support" + depends on ARCH_RDA || COMPILE_TEST + depends on OF_GPIO + select GPIOLIB_IRQCHIP + help + Say Y here to support RDA Micro GPIO controller. + config GPIO_REG bool help diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile index d2fd19c15bae..5c68c9a48fa3 100644 --- a/drivers/gpio/Makefile +++ b/drivers/gpio/Makefile @@ -115,6 +115,7 @@ obj-$(CONFIG_GPIO_PXA) += gpio-pxa.o obj-$(CONFIG_GPIO_RASPBERRYPI_EXP) += gpio-raspberrypi-exp.o obj-$(CONFIG_GPIO_RC5T583) += gpio-rc5t583.o obj-$(CONFIG_GPIO_RCAR) += gpio-rcar.o +obj-$(CONFIG_GPIO_RDA) += gpio-rda.o obj-$(CONFIG_GPIO_RDC321X) += gpio-rdc321x.o obj-$(CONFIG_GPIO_REG) += gpio-reg.o obj-$(CONFIG_ARCH_SA1100) += gpio-sa1100.o diff --git a/drivers/gpio/gpio-rda.c b/drivers/gpio/gpio-rda.c new file mode 100644 index 000000000000..5a4adeb25f72 --- /dev/null +++ b/drivers/gpio/gpio-rda.c @@ -0,0 +1,334 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * RDA Micro GPIO driver + * + * Copyright (C) 2012 RDA Micro Inc. + * Copyright (C) 2019 Manivannan Sadhasivam + */ + +#include <linux/bitops.h> +#include <linux/gpio/driver.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/of_device.h> +#include <linux/platform_device.h> +#include <linux/spinlock.h> + +#define RDA_GPIO_OEN_VAL 0x00 +#define RDA_GPIO_OEN_SET_OUT 0x04 +#define RDA_GPIO_OEN_SET_IN 0x08 +#define RDA_GPIO_VAL 0x0c +#define RDA_GPIO_SET 0x10 +#define RDA_GPIO_CLR 0x14 +#define RDA_GPIO_INT_CTRL_SET 0x18 +#define RDA_GPIO_INT_CTRL_CLR 0x1c +#define RDA_GPIO_INT_CLR 0x20 +#define RDA_GPIO_INT_STATUS 0x24 + +#define RDA_GPIO_IRQ_RISE_SHIFT 0 +#define RDA_GPIO_IRQ_FALL_SHIFT 8 +#define RDA_GPIO_DEBOUCE_SHIFT 16 +#define RDA_GPIO_LEVEL_SHIFT 24 + +#define RDA_GPIO_IRQ_MASK 0xff + +/* Each bank consists of 32 GPIOs */ +#define RDA_GPIO_BANK_NR 32 + +struct rda_gpio { + struct gpio_chip chip; + void __iomem *base; + spinlock_t lock; + struct irq_chip irq_chip; + int irq; +}; + +static void rda_gpio_update(struct gpio_chip *chip, unsigned int offset, + u16 reg, int val) +{ + struct rda_gpio *rda_gpio = gpiochip_get_data(chip); + void __iomem *base = rda_gpio->base; + unsigned long flags; + u32 tmp; + + spin_lock_irqsave(&rda_gpio->lock, flags); + tmp = readl_relaxed(base + reg); + + if (val) + tmp |= BIT(offset); + else + tmp &= ~BIT(offset); + + writel_relaxed(tmp, base + reg); + spin_unlock_irqrestore(&rda_gpio->lock, flags); +} + +static int rda_gpio_request(struct gpio_chip *chip, unsigned int offset) +{ + /* Not supported currently */ + return 0; +} + +static void rda_gpio_free(struct gpio_chip *chip, unsigned int offset) +{ + /* Not supported currently */ +} + +static int rda_gpio_direction_input(struct gpio_chip *chip, unsigned int offset) +{ + rda_gpio_update(chip, offset, RDA_GPIO_OEN_SET_IN, 1); + + return 0; +} + +static int rda_gpio_direction_output(struct gpio_chip *chip, + unsigned int offset, int value) +{ + rda_gpio_update(chip, offset, RDA_GPIO_OEN_SET_OUT, 1); + + return 0; +} + +static int rda_gpio_get(struct gpio_chip *chip, unsigned int offset) +{ + struct rda_gpio *rda_gpio = gpiochip_get_data(chip); + void __iomem *base = rda_gpio->base; + + if (readl_relaxed(base + RDA_GPIO_OEN_VAL) & BIT(offset)) + return !!(readl_relaxed(base + RDA_GPIO_VAL) & BIT(offset)); + else + return !!(readl_relaxed(base + RDA_GPIO_SET) & BIT(offset)); +} + +static void rda_gpio_set(struct gpio_chip *chip, unsigned int offset, int value) +{ + if (value) + rda_gpio_update(chip, offset, RDA_GPIO_SET, 1); + else + rda_gpio_update(chip, offset, RDA_GPIO_CLR, 1); +} + +static void rda_gpio_irq_mask(struct irq_data *data) +{ + struct gpio_chip *chip = irq_data_get_irq_chip_data(data); + struct rda_gpio *rda_gpio = gpiochip_get_data(chip); + void __iomem *base = rda_gpio->base; + u32 offset = irqd_to_hwirq(data); + u32 value; + + value = BIT(offset) << RDA_GPIO_IRQ_RISE_SHIFT; + value |= BIT(offset) << RDA_GPIO_IRQ_FALL_SHIFT; + + writel_relaxed(value, base + RDA_GPIO_INT_CTRL_CLR); +} + +static void rda_gpio_irq_ack(struct irq_data *data) +{ + struct gpio_chip *chip = irq_data_get_irq_chip_data(data); + u32 offset = irqd_to_hwirq(data); + + rda_gpio_update(chip, offset, RDA_GPIO_INT_CLR, 1); +} + +static int rda_gpio_set_irq(struct gpio_chip *chip, u32 offset, + unsigned int flow_type) +{ + struct rda_gpio *rda_gpio = gpiochip_get_data(chip); + void __iomem *base = rda_gpio->base; + u32 value; + + switch (flow_type) { + case IRQ_TYPE_EDGE_RISING: + /* Set rising edge trigger */ + value = BIT(offset) << RDA_GPIO_IRQ_RISE_SHIFT; + writel_relaxed(value, base + RDA_GPIO_INT_CTRL_SET); + + /* Switch to edge trigger interrupt */ + value = BIT(offset) << RDA_GPIO_LEVEL_SHIFT; + writel_relaxed(value, base + RDA_GPIO_INT_CTRL_CLR); + break; + + case IRQ_TYPE_EDGE_FALLING: + /* Set falling edge trigger */ + value = BIT(offset) << RDA_GPIO_IRQ_FALL_SHIFT; + writel_relaxed(value, base + RDA_GPIO_INT_CTRL_SET); + + /* Switch to edge trigger interrupt */ + value = BIT(offset) << RDA_GPIO_LEVEL_SHIFT; + writel_relaxed(value, base + RDA_GPIO_INT_CTRL_CLR); + break; + + case IRQ_TYPE_EDGE_BOTH: + /* Set both edge trigger */ + value = BIT(offset) << RDA_GPIO_IRQ_RISE_SHIFT; + value |= BIT(offset) << RDA_GPIO_IRQ_FALL_SHIFT; + writel_relaxed(value, base + RDA_GPIO_INT_CTRL_SET); + + /* Switch to edge trigger interrupt */ + value = BIT(offset) << RDA_GPIO_LEVEL_SHIFT; + writel_relaxed(value, base + RDA_GPIO_INT_CTRL_CLR); + break; + + case IRQ_TYPE_LEVEL_HIGH: + /* Set high level trigger */ + value = BIT(offset) << RDA_GPIO_IRQ_RISE_SHIFT; + + /* Switch to level trigger interrupt */ + value |= BIT(offset) << RDA_GPIO_LEVEL_SHIFT; + writel_relaxed(value, base + RDA_GPIO_INT_CTRL_SET); + break; + + case IRQ_TYPE_LEVEL_LOW: + /* Set low level trigger */ + value = BIT(offset) << RDA_GPIO_IRQ_FALL_SHIFT; + + /* Switch to level trigger interrupt */ + value |= BIT(offset) << RDA_GPIO_LEVEL_SHIFT; + writel_relaxed(value, base + RDA_GPIO_INT_CTRL_SET); + break; + + default: + return -EINVAL; + } + + return 0; +} + +static void rda_gpio_irq_unmask(struct irq_data *data) +{ + struct gpio_chip *chip = irq_data_get_irq_chip_data(data); + u32 offset = irqd_to_hwirq(data); + u32 trigger = irqd_get_trigger_type(data); + + rda_gpio_set_irq(chip, offset, trigger); +} + +static int rda_gpio_irq_set_type(struct irq_data *data, unsigned int flow_type) +{ + struct gpio_chip *chip = irq_data_get_irq_chip_data(data); + u32 offset = irqd_to_hwirq(data); + int ret; + + ret = rda_gpio_set_irq(chip, offset, flow_type); + if (ret) + return ret; + + if (flow_type & (IRQ_TYPE_LEVEL_LOW | IRQ_TYPE_LEVEL_HIGH)) + irq_set_handler_locked(data, handle_level_irq); + else if (flow_type & (IRQ_TYPE_EDGE_FALLING | IRQ_TYPE_EDGE_RISING)) + irq_set_handler_locked(data, handle_edge_irq); + + return 0; +} + +static void rda_gpio_irq_handler(struct irq_desc *desc) +{ + struct gpio_chip *chip = irq_desc_get_handler_data(desc); + struct irq_chip *ic = irq_desc_get_chip(desc); + struct rda_gpio *rda_gpio = gpiochip_get_data(chip); + unsigned long status; + u32 n, girq; + + chained_irq_enter(ic, desc); + + status = readl_relaxed(rda_gpio->base + RDA_GPIO_INT_STATUS); + /* Only lower 8 bits are capable of generating interrupts */ + status &= RDA_GPIO_IRQ_MASK; + + for_each_set_bit(n, &status, RDA_GPIO_BANK_NR) { + girq = irq_find_mapping(chip->irq.domain, n); + generic_handle_irq(girq); + } + + chained_irq_exit(ic, desc); +} + +static int rda_gpio_probe(struct platform_device *pdev) +{ + struct device_node *np = pdev->dev.of_node; + struct gpio_irq_chip *irq; + struct rda_gpio *rda_gpio; + u32 ngpios; + int ret; + + rda_gpio = devm_kzalloc(&pdev->dev, sizeof(*rda_gpio), GFP_KERNEL); + if (!rda_gpio) + return -ENOMEM; + + ret = of_property_read_u32(np, "ngpios", &ngpios); + if (ret < 0) + return ret; + + /* + * Not all ports have interrupt capability. For instance, on + * RDA8810PL, GPIOC doesn't support interrupt. So we must handle + * those also. + */ + rda_gpio->irq = platform_get_irq(pdev, 0); + + rda_gpio->base = devm_platform_ioremap_resource(pdev, 0); + if (IS_ERR(rda_gpio->base)) + return PTR_ERR(rda_gpio->base); + + spin_lock_init(&rda_gpio->lock); + + rda_gpio->chip.label = dev_name(&pdev->dev); + rda_gpio->chip.ngpio = ngpios; + rda_gpio->chip.base = -1; + rda_gpio->chip.parent = &pdev->dev; + rda_gpio->chip.of_node = np; + rda_gpio->chip.request = rda_gpio_request; + rda_gpio->chip.free = rda_gpio_free; + rda_gpio->chip.get = rda_gpio_get; + rda_gpio->chip.set = rda_gpio_set; + rda_gpio->chip.direction_input = rda_gpio_direction_input; + rda_gpio->chip.direction_output = rda_gpio_direction_output; + + if (rda_gpio->irq >= 0) { + rda_gpio->irq_chip.name = "rda-gpio", + rda_gpio->irq_chip.irq_ack = rda_gpio_irq_ack, + rda_gpio->irq_chip.irq_mask = rda_gpio_irq_mask, + rda_gpio->irq_chip.irq_unmask = rda_gpio_irq_unmask, + rda_gpio->irq_chip.irq_set_type = rda_gpio_irq_set_type, + rda_gpio->irq_chip.flags = IRQCHIP_SKIP_SET_WAKE, + + irq = &rda_gpio->chip.irq; + irq->chip = &rda_gpio->irq_chip; + irq->handler = handle_bad_irq; + irq->default_type = IRQ_TYPE_NONE; + irq->parent_handler = rda_gpio_irq_handler; + irq->parent_handler_data = rda_gpio; + irq->num_parents = 1; + irq->parents = &rda_gpio->irq; + } + + ret = devm_gpiochip_add_data(&pdev->dev, &rda_gpio->chip, rda_gpio); + if (ret < 0) { + dev_err(&pdev->dev, "Could not register gpiochip %d\n", ret); + return ret; + } + + platform_set_drvdata(pdev, rda_gpio); + + return 0; +} + +static const struct of_device_id rda_gpio_of_match[] = { + { .compatible = "rda,8810pl-gpio", }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, rda_gpio_of_match); + +static struct platform_driver rda_gpio_driver = { + .probe = rda_gpio_probe, + .driver = { + .name = "rda-gpio", + .of_match_table = rda_gpio_of_match, + }, +}; + +module_platform_driver_probe(rda_gpio_driver, rda_gpio_probe); + +MODULE_DESCRIPTION("RDA Micro GPIO driver"); +MODULE_AUTHOR("Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>"); +MODULE_LICENSE("GPL v2"); -- 2.17.1 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH 2/4] gpio: Add RDA Micro GPIO controller support 2019-10-13 11:40 ` [PATCH 2/4] gpio: Add RDA Micro GPIO controller support Manivannan Sadhasivam @ 2019-10-14 14:25 ` Bartosz Golaszewski 2019-10-15 16:51 ` Manivannan Sadhasivam 0 siblings, 1 reply; 7+ messages in thread From: Bartosz Golaszewski @ 2019-10-14 14:25 UTC (permalink / raw) To: Manivannan Sadhasivam Cc: Linus Walleij, arm-soc, linux-unisoc, linux-gpio, LKML, Orson Zhai niedz., 13 paź 2019 o 13:40 Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> napisał(a): > > Add support for GPIO controller from RDA Micro. Looks nice and clean, just a couple nits. > > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > --- > drivers/gpio/Kconfig | 8 + > drivers/gpio/Makefile | 1 + > drivers/gpio/gpio-rda.c | 334 ++++++++++++++++++++++++++++++++++++++++ > 3 files changed, 343 insertions(+) > create mode 100644 drivers/gpio/gpio-rda.c > > diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig > index 38e096e6925f..71826e61fdb3 100644 > --- a/drivers/gpio/Kconfig > +++ b/drivers/gpio/Kconfig > @@ -435,6 +435,14 @@ config GPIO_RCAR > help > Say yes here to support GPIO on Renesas R-Car SoCs. > > +config GPIO_RDA > + bool "RDA Micro GPIO controller support" > + depends on ARCH_RDA || COMPILE_TEST > + depends on OF_GPIO > + select GPIOLIB_IRQCHIP > + help > + Say Y here to support RDA Micro GPIO controller. > + > config GPIO_REG > bool > help > diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile > index d2fd19c15bae..5c68c9a48fa3 100644 > --- a/drivers/gpio/Makefile > +++ b/drivers/gpio/Makefile > @@ -115,6 +115,7 @@ obj-$(CONFIG_GPIO_PXA) += gpio-pxa.o > obj-$(CONFIG_GPIO_RASPBERRYPI_EXP) += gpio-raspberrypi-exp.o > obj-$(CONFIG_GPIO_RC5T583) += gpio-rc5t583.o > obj-$(CONFIG_GPIO_RCAR) += gpio-rcar.o > +obj-$(CONFIG_GPIO_RDA) += gpio-rda.o > obj-$(CONFIG_GPIO_RDC321X) += gpio-rdc321x.o > obj-$(CONFIG_GPIO_REG) += gpio-reg.o > obj-$(CONFIG_ARCH_SA1100) += gpio-sa1100.o > diff --git a/drivers/gpio/gpio-rda.c b/drivers/gpio/gpio-rda.c > new file mode 100644 > index 000000000000..5a4adeb25f72 > --- /dev/null > +++ b/drivers/gpio/gpio-rda.c > @@ -0,0 +1,334 @@ > +// SPDX-License-Identifier: GPL-2.0-only > +/* > + * RDA Micro GPIO driver > + * > + * Copyright (C) 2012 RDA Micro Inc. > + * Copyright (C) 2019 Manivannan Sadhasivam > + */ > + > +#include <linux/bitops.h> > +#include <linux/gpio/driver.h> > +#include <linux/kernel.h> > +#include <linux/module.h> > +#include <linux/of_device.h> > +#include <linux/platform_device.h> > +#include <linux/spinlock.h> > + > +#define RDA_GPIO_OEN_VAL 0x00 > +#define RDA_GPIO_OEN_SET_OUT 0x04 > +#define RDA_GPIO_OEN_SET_IN 0x08 > +#define RDA_GPIO_VAL 0x0c > +#define RDA_GPIO_SET 0x10 > +#define RDA_GPIO_CLR 0x14 > +#define RDA_GPIO_INT_CTRL_SET 0x18 > +#define RDA_GPIO_INT_CTRL_CLR 0x1c > +#define RDA_GPIO_INT_CLR 0x20 > +#define RDA_GPIO_INT_STATUS 0x24 > + > +#define RDA_GPIO_IRQ_RISE_SHIFT 0 > +#define RDA_GPIO_IRQ_FALL_SHIFT 8 > +#define RDA_GPIO_DEBOUCE_SHIFT 16 > +#define RDA_GPIO_LEVEL_SHIFT 24 > + > +#define RDA_GPIO_IRQ_MASK 0xff > + > +/* Each bank consists of 32 GPIOs */ > +#define RDA_GPIO_BANK_NR 32 > + > +struct rda_gpio { > + struct gpio_chip chip; > + void __iomem *base; > + spinlock_t lock; > + struct irq_chip irq_chip; > + int irq; > +}; > + > +static void rda_gpio_update(struct gpio_chip *chip, unsigned int offset, > + u16 reg, int val) > +{ > + struct rda_gpio *rda_gpio = gpiochip_get_data(chip); > + void __iomem *base = rda_gpio->base; > + unsigned long flags; > + u32 tmp; > + > + spin_lock_irqsave(&rda_gpio->lock, flags); > + tmp = readl_relaxed(base + reg); > + > + if (val) > + tmp |= BIT(offset); > + else > + tmp &= ~BIT(offset); > + > + writel_relaxed(tmp, base + reg); > + spin_unlock_irqrestore(&rda_gpio->lock, flags); > +} If you used the mmio regmap, you could save all this code and reuse regmap's update helpers. This is just a suggestion, not a requirement though. > + > +static int rda_gpio_request(struct gpio_chip *chip, unsigned int offset) > +{ > + /* Not supported currently */ > + return 0; > +} > + > +static void rda_gpio_free(struct gpio_chip *chip, unsigned int offset) > +{ > + /* Not supported currently */ > +} Just don't implement these callbacks if they're doing nothing. > + > +static int rda_gpio_direction_input(struct gpio_chip *chip, unsigned int offset) > +{ > + rda_gpio_update(chip, offset, RDA_GPIO_OEN_SET_IN, 1); > + > + return 0; > +} > + > +static int rda_gpio_direction_output(struct gpio_chip *chip, > + unsigned int offset, int value) > +{ > + rda_gpio_update(chip, offset, RDA_GPIO_OEN_SET_OUT, 1); > + > + return 0; > +} > + > +static int rda_gpio_get(struct gpio_chip *chip, unsigned int offset) > +{ > + struct rda_gpio *rda_gpio = gpiochip_get_data(chip); > + void __iomem *base = rda_gpio->base; > + > + if (readl_relaxed(base + RDA_GPIO_OEN_VAL) & BIT(offset)) > + return !!(readl_relaxed(base + RDA_GPIO_VAL) & BIT(offset)); > + else > + return !!(readl_relaxed(base + RDA_GPIO_SET) & BIT(offset)); > +} > + > +static void rda_gpio_set(struct gpio_chip *chip, unsigned int offset, int value) > +{ > + if (value) > + rda_gpio_update(chip, offset, RDA_GPIO_SET, 1); > + else > + rda_gpio_update(chip, offset, RDA_GPIO_CLR, 1); > +} > + > +static void rda_gpio_irq_mask(struct irq_data *data) > +{ > + struct gpio_chip *chip = irq_data_get_irq_chip_data(data); > + struct rda_gpio *rda_gpio = gpiochip_get_data(chip); > + void __iomem *base = rda_gpio->base; > + u32 offset = irqd_to_hwirq(data); > + u32 value; > + > + value = BIT(offset) << RDA_GPIO_IRQ_RISE_SHIFT; > + value |= BIT(offset) << RDA_GPIO_IRQ_FALL_SHIFT; > + > + writel_relaxed(value, base + RDA_GPIO_INT_CTRL_CLR); > +} > + > +static void rda_gpio_irq_ack(struct irq_data *data) > +{ > + struct gpio_chip *chip = irq_data_get_irq_chip_data(data); > + u32 offset = irqd_to_hwirq(data); > + > + rda_gpio_update(chip, offset, RDA_GPIO_INT_CLR, 1); > +} > + > +static int rda_gpio_set_irq(struct gpio_chip *chip, u32 offset, > + unsigned int flow_type) > +{ > + struct rda_gpio *rda_gpio = gpiochip_get_data(chip); > + void __iomem *base = rda_gpio->base; > + u32 value; > + > + switch (flow_type) { > + case IRQ_TYPE_EDGE_RISING: > + /* Set rising edge trigger */ > + value = BIT(offset) << RDA_GPIO_IRQ_RISE_SHIFT; > + writel_relaxed(value, base + RDA_GPIO_INT_CTRL_SET); > + > + /* Switch to edge trigger interrupt */ > + value = BIT(offset) << RDA_GPIO_LEVEL_SHIFT; > + writel_relaxed(value, base + RDA_GPIO_INT_CTRL_CLR); > + break; > + > + case IRQ_TYPE_EDGE_FALLING: > + /* Set falling edge trigger */ > + value = BIT(offset) << RDA_GPIO_IRQ_FALL_SHIFT; > + writel_relaxed(value, base + RDA_GPIO_INT_CTRL_SET); > + > + /* Switch to edge trigger interrupt */ > + value = BIT(offset) << RDA_GPIO_LEVEL_SHIFT; > + writel_relaxed(value, base + RDA_GPIO_INT_CTRL_CLR); > + break; > + > + case IRQ_TYPE_EDGE_BOTH: > + /* Set both edge trigger */ > + value = BIT(offset) << RDA_GPIO_IRQ_RISE_SHIFT; > + value |= BIT(offset) << RDA_GPIO_IRQ_FALL_SHIFT; > + writel_relaxed(value, base + RDA_GPIO_INT_CTRL_SET); > + > + /* Switch to edge trigger interrupt */ > + value = BIT(offset) << RDA_GPIO_LEVEL_SHIFT; > + writel_relaxed(value, base + RDA_GPIO_INT_CTRL_CLR); > + break; > + > + case IRQ_TYPE_LEVEL_HIGH: > + /* Set high level trigger */ > + value = BIT(offset) << RDA_GPIO_IRQ_RISE_SHIFT; > + > + /* Switch to level trigger interrupt */ > + value |= BIT(offset) << RDA_GPIO_LEVEL_SHIFT; > + writel_relaxed(value, base + RDA_GPIO_INT_CTRL_SET); > + break; > + > + case IRQ_TYPE_LEVEL_LOW: > + /* Set low level trigger */ > + value = BIT(offset) << RDA_GPIO_IRQ_FALL_SHIFT; > + > + /* Switch to level trigger interrupt */ > + value |= BIT(offset) << RDA_GPIO_LEVEL_SHIFT; > + writel_relaxed(value, base + RDA_GPIO_INT_CTRL_SET); > + break; > + > + default: > + return -EINVAL; > + } > + > + return 0; > +} > + > +static void rda_gpio_irq_unmask(struct irq_data *data) > +{ > + struct gpio_chip *chip = irq_data_get_irq_chip_data(data); > + u32 offset = irqd_to_hwirq(data); > + u32 trigger = irqd_get_trigger_type(data); > + > + rda_gpio_set_irq(chip, offset, trigger); > +} > + > +static int rda_gpio_irq_set_type(struct irq_data *data, unsigned int flow_type) > +{ > + struct gpio_chip *chip = irq_data_get_irq_chip_data(data); > + u32 offset = irqd_to_hwirq(data); > + int ret; > + > + ret = rda_gpio_set_irq(chip, offset, flow_type); > + if (ret) > + return ret; > + > + if (flow_type & (IRQ_TYPE_LEVEL_LOW | IRQ_TYPE_LEVEL_HIGH)) > + irq_set_handler_locked(data, handle_level_irq); > + else if (flow_type & (IRQ_TYPE_EDGE_FALLING | IRQ_TYPE_EDGE_RISING)) > + irq_set_handler_locked(data, handle_edge_irq); > + > + return 0; > +} > + > +static void rda_gpio_irq_handler(struct irq_desc *desc) > +{ > + struct gpio_chip *chip = irq_desc_get_handler_data(desc); > + struct irq_chip *ic = irq_desc_get_chip(desc); > + struct rda_gpio *rda_gpio = gpiochip_get_data(chip); > + unsigned long status; > + u32 n, girq; > + > + chained_irq_enter(ic, desc); > + > + status = readl_relaxed(rda_gpio->base + RDA_GPIO_INT_STATUS); > + /* Only lower 8 bits are capable of generating interrupts */ > + status &= RDA_GPIO_IRQ_MASK; > + > + for_each_set_bit(n, &status, RDA_GPIO_BANK_NR) { > + girq = irq_find_mapping(chip->irq.domain, n); > + generic_handle_irq(girq); > + } > + > + chained_irq_exit(ic, desc); > +} > + > +static int rda_gpio_probe(struct platform_device *pdev) > +{ > + struct device_node *np = pdev->dev.of_node; > + struct gpio_irq_chip *irq; Can you call this variable irq_chip? Visually it interferes with rda_gpio->irq too much. > + struct rda_gpio *rda_gpio; > + u32 ngpios; > + int ret; > + > + rda_gpio = devm_kzalloc(&pdev->dev, sizeof(*rda_gpio), GFP_KERNEL); > + if (!rda_gpio) > + return -ENOMEM; > + > + ret = of_property_read_u32(np, "ngpios", &ngpios); > + if (ret < 0) > + return ret; > + Please use the generic device property helpers unless it's really necessary to use of_ variants. Also: remove the of_device.h include. > + /* > + * Not all ports have interrupt capability. For instance, on > + * RDA8810PL, GPIOC doesn't support interrupt. So we must handle > + * those also. > + */ > + rda_gpio->irq = platform_get_irq(pdev, 0); > + > + rda_gpio->base = devm_platform_ioremap_resource(pdev, 0); > + if (IS_ERR(rda_gpio->base)) > + return PTR_ERR(rda_gpio->base); > + > + spin_lock_init(&rda_gpio->lock); > + > + rda_gpio->chip.label = dev_name(&pdev->dev); > + rda_gpio->chip.ngpio = ngpios; > + rda_gpio->chip.base = -1; > + rda_gpio->chip.parent = &pdev->dev; > + rda_gpio->chip.of_node = np; > + rda_gpio->chip.request = rda_gpio_request; > + rda_gpio->chip.free = rda_gpio_free; > + rda_gpio->chip.get = rda_gpio_get; > + rda_gpio->chip.set = rda_gpio_set; > + rda_gpio->chip.direction_input = rda_gpio_direction_input; > + rda_gpio->chip.direction_output = rda_gpio_direction_output; > + > + if (rda_gpio->irq >= 0) { > + rda_gpio->irq_chip.name = "rda-gpio", > + rda_gpio->irq_chip.irq_ack = rda_gpio_irq_ack, > + rda_gpio->irq_chip.irq_mask = rda_gpio_irq_mask, > + rda_gpio->irq_chip.irq_unmask = rda_gpio_irq_unmask, > + rda_gpio->irq_chip.irq_set_type = rda_gpio_irq_set_type, > + rda_gpio->irq_chip.flags = IRQCHIP_SKIP_SET_WAKE, > + > + irq = &rda_gpio->chip.irq; > + irq->chip = &rda_gpio->irq_chip; > + irq->handler = handle_bad_irq; > + irq->default_type = IRQ_TYPE_NONE; > + irq->parent_handler = rda_gpio_irq_handler; > + irq->parent_handler_data = rda_gpio; > + irq->num_parents = 1; > + irq->parents = &rda_gpio->irq; > + } > + > + ret = devm_gpiochip_add_data(&pdev->dev, &rda_gpio->chip, rda_gpio); I'd simply do 'return devm_gpiochip_add_data()' here, not much else can fail in this driver's probe. Bart > + if (ret < 0) { > + dev_err(&pdev->dev, "Could not register gpiochip %d\n", ret); > + return ret; > + } > + > + platform_set_drvdata(pdev, rda_gpio); > + > + return 0; > +} > + > +static const struct of_device_id rda_gpio_of_match[] = { > + { .compatible = "rda,8810pl-gpio", }, > + { /* sentinel */ } > +}; > +MODULE_DEVICE_TABLE(of, rda_gpio_of_match); > + > +static struct platform_driver rda_gpio_driver = { > + .probe = rda_gpio_probe, > + .driver = { > + .name = "rda-gpio", > + .of_match_table = rda_gpio_of_match, > + }, > +}; > + > +module_platform_driver_probe(rda_gpio_driver, rda_gpio_probe); > + > +MODULE_DESCRIPTION("RDA Micro GPIO driver"); > +MODULE_AUTHOR("Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>"); > +MODULE_LICENSE("GPL v2"); > -- > 2.17.1 > ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH 2/4] gpio: Add RDA Micro GPIO controller support 2019-10-14 14:25 ` Bartosz Golaszewski @ 2019-10-15 16:51 ` Manivannan Sadhasivam 0 siblings, 0 replies; 7+ messages in thread From: Manivannan Sadhasivam @ 2019-10-15 16:51 UTC (permalink / raw) To: Bartosz Golaszewski Cc: Linus Walleij, arm-soc, linux-unisoc, linux-gpio, LKML, Orson Zhai Hi Bartosz, Thanks for the quick review! Please find the reply inline. On Mon, Oct 14, 2019 at 04:25:29PM +0200, Bartosz Golaszewski wrote: > niedz., 13 paź 2019 o 13:40 Manivannan Sadhasivam > <manivannan.sadhasivam@linaro.org> napisał(a): > > > > Add support for GPIO controller from RDA Micro. > > Looks nice and clean, just a couple nits. > > > > > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > > --- > > drivers/gpio/Kconfig | 8 + > > drivers/gpio/Makefile | 1 + > > drivers/gpio/gpio-rda.c | 334 ++++++++++++++++++++++++++++++++++++++++ > > 3 files changed, 343 insertions(+) > > create mode 100644 drivers/gpio/gpio-rda.c > > > > diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig > > index 38e096e6925f..71826e61fdb3 100644 > > --- a/drivers/gpio/Kconfig > > +++ b/drivers/gpio/Kconfig > > @@ -435,6 +435,14 @@ config GPIO_RCAR > > help > > Say yes here to support GPIO on Renesas R-Car SoCs. > > > > +config GPIO_RDA > > + bool "RDA Micro GPIO controller support" > > + depends on ARCH_RDA || COMPILE_TEST > > + depends on OF_GPIO > > + select GPIOLIB_IRQCHIP > > + help > > + Say Y here to support RDA Micro GPIO controller. > > + > > config GPIO_REG > > bool > > help > > diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile > > index d2fd19c15bae..5c68c9a48fa3 100644 > > --- a/drivers/gpio/Makefile > > +++ b/drivers/gpio/Makefile > > @@ -115,6 +115,7 @@ obj-$(CONFIG_GPIO_PXA) += gpio-pxa.o > > obj-$(CONFIG_GPIO_RASPBERRYPI_EXP) += gpio-raspberrypi-exp.o > > obj-$(CONFIG_GPIO_RC5T583) += gpio-rc5t583.o > > obj-$(CONFIG_GPIO_RCAR) += gpio-rcar.o > > +obj-$(CONFIG_GPIO_RDA) += gpio-rda.o > > obj-$(CONFIG_GPIO_RDC321X) += gpio-rdc321x.o > > obj-$(CONFIG_GPIO_REG) += gpio-reg.o > > obj-$(CONFIG_ARCH_SA1100) += gpio-sa1100.o > > diff --git a/drivers/gpio/gpio-rda.c b/drivers/gpio/gpio-rda.c > > new file mode 100644 > > index 000000000000..5a4adeb25f72 > > --- /dev/null > > +++ b/drivers/gpio/gpio-rda.c > > @@ -0,0 +1,334 @@ > > +// SPDX-License-Identifier: GPL-2.0-only > > +/* > > + * RDA Micro GPIO driver > > + * > > + * Copyright (C) 2012 RDA Micro Inc. > > + * Copyright (C) 2019 Manivannan Sadhasivam > > + */ > > + > > +#include <linux/bitops.h> > > +#include <linux/gpio/driver.h> > > +#include <linux/kernel.h> > > +#include <linux/module.h> > > +#include <linux/of_device.h> > > +#include <linux/platform_device.h> > > +#include <linux/spinlock.h> > > + > > +#define RDA_GPIO_OEN_VAL 0x00 > > +#define RDA_GPIO_OEN_SET_OUT 0x04 > > +#define RDA_GPIO_OEN_SET_IN 0x08 > > +#define RDA_GPIO_VAL 0x0c > > +#define RDA_GPIO_SET 0x10 > > +#define RDA_GPIO_CLR 0x14 > > +#define RDA_GPIO_INT_CTRL_SET 0x18 > > +#define RDA_GPIO_INT_CTRL_CLR 0x1c > > +#define RDA_GPIO_INT_CLR 0x20 > > +#define RDA_GPIO_INT_STATUS 0x24 > > + > > +#define RDA_GPIO_IRQ_RISE_SHIFT 0 > > +#define RDA_GPIO_IRQ_FALL_SHIFT 8 > > +#define RDA_GPIO_DEBOUCE_SHIFT 16 > > +#define RDA_GPIO_LEVEL_SHIFT 24 > > + > > +#define RDA_GPIO_IRQ_MASK 0xff > > + > > +/* Each bank consists of 32 GPIOs */ > > +#define RDA_GPIO_BANK_NR 32 > > + > > +struct rda_gpio { > > + struct gpio_chip chip; > > + void __iomem *base; > > + spinlock_t lock; > > + struct irq_chip irq_chip; > > + int irq; > > +}; > > + > > +static void rda_gpio_update(struct gpio_chip *chip, unsigned int offset, > > + u16 reg, int val) > > +{ > > + struct rda_gpio *rda_gpio = gpiochip_get_data(chip); > > + void __iomem *base = rda_gpio->base; > > + unsigned long flags; > > + u32 tmp; > > + > > + spin_lock_irqsave(&rda_gpio->lock, flags); > > + tmp = readl_relaxed(base + reg); > > + > > + if (val) > > + tmp |= BIT(offset); > > + else > > + tmp &= ~BIT(offset); > > + > > + writel_relaxed(tmp, base + reg); > > + spin_unlock_irqrestore(&rda_gpio->lock, flags); > > +} > > If you used the mmio regmap, you could save all this code and reuse > regmap's update helpers. This is just a suggestion, not a requirement > though. > Agree. I'll post a patch later once this driver gets in. > > + > > +static int rda_gpio_request(struct gpio_chip *chip, unsigned int offset) > > +{ > > + /* Not supported currently */ > > + return 0; > > +} > > + > > +static void rda_gpio_free(struct gpio_chip *chip, unsigned int offset) > > +{ > > + /* Not supported currently */ > > +} > > Just don't implement these callbacks if they're doing nothing. > Hmm. Since these are some critical callbacks, I thought the drivers should explicitly expose even not implemented. But I can remove them. > > + > > +static int rda_gpio_direction_input(struct gpio_chip *chip, unsigned int offset) > > +{ > > + rda_gpio_update(chip, offset, RDA_GPIO_OEN_SET_IN, 1); > > + > > + return 0; > > +} > > + > > +static int rda_gpio_direction_output(struct gpio_chip *chip, > > + unsigned int offset, int value) > > +{ > > + rda_gpio_update(chip, offset, RDA_GPIO_OEN_SET_OUT, 1); > > + > > + return 0; > > +} > > + > > +static int rda_gpio_get(struct gpio_chip *chip, unsigned int offset) > > +{ > > + struct rda_gpio *rda_gpio = gpiochip_get_data(chip); > > + void __iomem *base = rda_gpio->base; > > + > > + if (readl_relaxed(base + RDA_GPIO_OEN_VAL) & BIT(offset)) > > + return !!(readl_relaxed(base + RDA_GPIO_VAL) & BIT(offset)); > > + else > > + return !!(readl_relaxed(base + RDA_GPIO_SET) & BIT(offset)); > > +} > > + > > +static void rda_gpio_set(struct gpio_chip *chip, unsigned int offset, int value) > > +{ > > + if (value) > > + rda_gpio_update(chip, offset, RDA_GPIO_SET, 1); > > + else > > + rda_gpio_update(chip, offset, RDA_GPIO_CLR, 1); > > +} > > + > > +static void rda_gpio_irq_mask(struct irq_data *data) > > +{ > > + struct gpio_chip *chip = irq_data_get_irq_chip_data(data); > > + struct rda_gpio *rda_gpio = gpiochip_get_data(chip); > > + void __iomem *base = rda_gpio->base; > > + u32 offset = irqd_to_hwirq(data); > > + u32 value; > > + > > + value = BIT(offset) << RDA_GPIO_IRQ_RISE_SHIFT; > > + value |= BIT(offset) << RDA_GPIO_IRQ_FALL_SHIFT; > > + > > + writel_relaxed(value, base + RDA_GPIO_INT_CTRL_CLR); > > +} > > + > > +static void rda_gpio_irq_ack(struct irq_data *data) > > +{ > > + struct gpio_chip *chip = irq_data_get_irq_chip_data(data); > > + u32 offset = irqd_to_hwirq(data); > > + > > + rda_gpio_update(chip, offset, RDA_GPIO_INT_CLR, 1); > > +} > > + > > +static int rda_gpio_set_irq(struct gpio_chip *chip, u32 offset, > > + unsigned int flow_type) > > +{ > > + struct rda_gpio *rda_gpio = gpiochip_get_data(chip); > > + void __iomem *base = rda_gpio->base; > > + u32 value; > > + > > + switch (flow_type) { > > + case IRQ_TYPE_EDGE_RISING: > > + /* Set rising edge trigger */ > > + value = BIT(offset) << RDA_GPIO_IRQ_RISE_SHIFT; > > + writel_relaxed(value, base + RDA_GPIO_INT_CTRL_SET); > > + > > + /* Switch to edge trigger interrupt */ > > + value = BIT(offset) << RDA_GPIO_LEVEL_SHIFT; > > + writel_relaxed(value, base + RDA_GPIO_INT_CTRL_CLR); > > + break; > > + > > + case IRQ_TYPE_EDGE_FALLING: > > + /* Set falling edge trigger */ > > + value = BIT(offset) << RDA_GPIO_IRQ_FALL_SHIFT; > > + writel_relaxed(value, base + RDA_GPIO_INT_CTRL_SET); > > + > > + /* Switch to edge trigger interrupt */ > > + value = BIT(offset) << RDA_GPIO_LEVEL_SHIFT; > > + writel_relaxed(value, base + RDA_GPIO_INT_CTRL_CLR); > > + break; > > + > > + case IRQ_TYPE_EDGE_BOTH: > > + /* Set both edge trigger */ > > + value = BIT(offset) << RDA_GPIO_IRQ_RISE_SHIFT; > > + value |= BIT(offset) << RDA_GPIO_IRQ_FALL_SHIFT; > > + writel_relaxed(value, base + RDA_GPIO_INT_CTRL_SET); > > + > > + /* Switch to edge trigger interrupt */ > > + value = BIT(offset) << RDA_GPIO_LEVEL_SHIFT; > > + writel_relaxed(value, base + RDA_GPIO_INT_CTRL_CLR); > > + break; > > + > > + case IRQ_TYPE_LEVEL_HIGH: > > + /* Set high level trigger */ > > + value = BIT(offset) << RDA_GPIO_IRQ_RISE_SHIFT; > > + > > + /* Switch to level trigger interrupt */ > > + value |= BIT(offset) << RDA_GPIO_LEVEL_SHIFT; > > + writel_relaxed(value, base + RDA_GPIO_INT_CTRL_SET); > > + break; > > + > > + case IRQ_TYPE_LEVEL_LOW: > > + /* Set low level trigger */ > > + value = BIT(offset) << RDA_GPIO_IRQ_FALL_SHIFT; > > + > > + /* Switch to level trigger interrupt */ > > + value |= BIT(offset) << RDA_GPIO_LEVEL_SHIFT; > > + writel_relaxed(value, base + RDA_GPIO_INT_CTRL_SET); > > + break; > > + > > + default: > > + return -EINVAL; > > + } > > + > > + return 0; > > +} > > + > > +static void rda_gpio_irq_unmask(struct irq_data *data) > > +{ > > + struct gpio_chip *chip = irq_data_get_irq_chip_data(data); > > + u32 offset = irqd_to_hwirq(data); > > + u32 trigger = irqd_get_trigger_type(data); > > + > > + rda_gpio_set_irq(chip, offset, trigger); > > +} > > + > > +static int rda_gpio_irq_set_type(struct irq_data *data, unsigned int flow_type) > > +{ > > + struct gpio_chip *chip = irq_data_get_irq_chip_data(data); > > + u32 offset = irqd_to_hwirq(data); > > + int ret; > > + > > + ret = rda_gpio_set_irq(chip, offset, flow_type); > > + if (ret) > > + return ret; > > + > > + if (flow_type & (IRQ_TYPE_LEVEL_LOW | IRQ_TYPE_LEVEL_HIGH)) > > + irq_set_handler_locked(data, handle_level_irq); > > + else if (flow_type & (IRQ_TYPE_EDGE_FALLING | IRQ_TYPE_EDGE_RISING)) > > + irq_set_handler_locked(data, handle_edge_irq); > > + > > + return 0; > > +} > > + > > +static void rda_gpio_irq_handler(struct irq_desc *desc) > > +{ > > + struct gpio_chip *chip = irq_desc_get_handler_data(desc); > > + struct irq_chip *ic = irq_desc_get_chip(desc); > > + struct rda_gpio *rda_gpio = gpiochip_get_data(chip); > > + unsigned long status; > > + u32 n, girq; > > + > > + chained_irq_enter(ic, desc); > > + > > + status = readl_relaxed(rda_gpio->base + RDA_GPIO_INT_STATUS); > > + /* Only lower 8 bits are capable of generating interrupts */ > > + status &= RDA_GPIO_IRQ_MASK; > > + > > + for_each_set_bit(n, &status, RDA_GPIO_BANK_NR) { > > + girq = irq_find_mapping(chip->irq.domain, n); > > + generic_handle_irq(girq); > > + } > > + > > + chained_irq_exit(ic, desc); > > +} > > + > > +static int rda_gpio_probe(struct platform_device *pdev) > > +{ > > + struct device_node *np = pdev->dev.of_node; > > + struct gpio_irq_chip *irq; > > Can you call this variable irq_chip? Visually it interferes with > rda_gpio->irq too much. > okay. > > + struct rda_gpio *rda_gpio; > > + u32 ngpios; > > + int ret; > > + > > + rda_gpio = devm_kzalloc(&pdev->dev, sizeof(*rda_gpio), GFP_KERNEL); > > + if (!rda_gpio) > > + return -ENOMEM; > > + > > + ret = of_property_read_u32(np, "ngpios", &ngpios); > > + if (ret < 0) > > + return ret; > > + > > Please use the generic device property helpers unless it's really > necessary to use of_ variants. Also: remove the of_device.h include. > okay. > > + /* > > + * Not all ports have interrupt capability. For instance, on > > + * RDA8810PL, GPIOC doesn't support interrupt. So we must handle > > + * those also. > > + */ > > + rda_gpio->irq = platform_get_irq(pdev, 0); > > + > > + rda_gpio->base = devm_platform_ioremap_resource(pdev, 0); > > + if (IS_ERR(rda_gpio->base)) > > + return PTR_ERR(rda_gpio->base); > > + > > + spin_lock_init(&rda_gpio->lock); > > + > > + rda_gpio->chip.label = dev_name(&pdev->dev); > > + rda_gpio->chip.ngpio = ngpios; > > + rda_gpio->chip.base = -1; > > + rda_gpio->chip.parent = &pdev->dev; > > + rda_gpio->chip.of_node = np; > > + rda_gpio->chip.request = rda_gpio_request; > > + rda_gpio->chip.free = rda_gpio_free; > > + rda_gpio->chip.get = rda_gpio_get; > > + rda_gpio->chip.set = rda_gpio_set; > > + rda_gpio->chip.direction_input = rda_gpio_direction_input; > > + rda_gpio->chip.direction_output = rda_gpio_direction_output; > > + > > + if (rda_gpio->irq >= 0) { > > + rda_gpio->irq_chip.name = "rda-gpio", > > + rda_gpio->irq_chip.irq_ack = rda_gpio_irq_ack, > > + rda_gpio->irq_chip.irq_mask = rda_gpio_irq_mask, > > + rda_gpio->irq_chip.irq_unmask = rda_gpio_irq_unmask, > > + rda_gpio->irq_chip.irq_set_type = rda_gpio_irq_set_type, > > + rda_gpio->irq_chip.flags = IRQCHIP_SKIP_SET_WAKE, > > + > > + irq = &rda_gpio->chip.irq; > > + irq->chip = &rda_gpio->irq_chip; > > + irq->handler = handle_bad_irq; > > + irq->default_type = IRQ_TYPE_NONE; > > + irq->parent_handler = rda_gpio_irq_handler; > > + irq->parent_handler_data = rda_gpio; > > + irq->num_parents = 1; > > + irq->parents = &rda_gpio->irq; > > + } > > + > > + ret = devm_gpiochip_add_data(&pdev->dev, &rda_gpio->chip, rda_gpio); > > I'd simply do 'return devm_gpiochip_add_data()' here, not much else > can fail in this driver's probe. > okay. I'll just move the platform_set_drvdata() call up and return directly. Thanks, Mani > Bart > > > + if (ret < 0) { > > + dev_err(&pdev->dev, "Could not register gpiochip %d\n", ret); > > + return ret; > > + } > > + > > + platform_set_drvdata(pdev, rda_gpio); > > + > > + return 0; > > +} > > + > > +static const struct of_device_id rda_gpio_of_match[] = { > > + { .compatible = "rda,8810pl-gpio", }, > > + { /* sentinel */ } > > +}; > > +MODULE_DEVICE_TABLE(of, rda_gpio_of_match); > > + > > +static struct platform_driver rda_gpio_driver = { > > + .probe = rda_gpio_probe, > > + .driver = { > > + .name = "rda-gpio", > > + .of_match_table = rda_gpio_of_match, > > + }, > > +}; > > + > > +module_platform_driver_probe(rda_gpio_driver, rda_gpio_probe); > > + > > +MODULE_DESCRIPTION("RDA Micro GPIO driver"); > > +MODULE_AUTHOR("Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>"); > > +MODULE_LICENSE("GPL v2"); > > -- > > 2.17.1 > > ^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH 3/4] ARM: dts: Add RDA8810PL GPIO controllers 2019-10-13 11:40 [PATCH 0/4] Add GPIO support for RDA8810PL SoC Manivannan Sadhasivam 2019-10-13 11:40 ` [PATCH 1/4] dt-bindings: gpio: Add devicetree binding for RDA Micro GPIO controller Manivannan Sadhasivam 2019-10-13 11:40 ` [PATCH 2/4] gpio: Add RDA Micro GPIO controller support Manivannan Sadhasivam @ 2019-10-13 11:40 ` Manivannan Sadhasivam 2019-10-13 11:40 ` [PATCH 4/4] MAINTAINERS: Add entry for RDA Micro GPIO driver and binding Manivannan Sadhasivam 3 siblings, 0 replies; 7+ messages in thread From: Manivannan Sadhasivam @ 2019-10-13 11:40 UTC (permalink / raw) To: linus.walleij, bgolaszewski Cc: linux-arm-kernel, linux-unisoc, linux-gpio, linux-kernel, orsonzhai, Manivannan Sadhasivam Add GPIO controllers for RDA8810PL SoC. There are 4 GPIO controllers in this SoC with maximum of 32 gpios. Except GPIOC, all controllers are capable of generating edge/level interrupts from first 8 lines. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> --- arch/arm/boot/dts/rda8810pl.dtsi | 48 ++++++++++++++++++++++++++++++++ 1 file changed, 48 insertions(+) diff --git a/arch/arm/boot/dts/rda8810pl.dtsi b/arch/arm/boot/dts/rda8810pl.dtsi index 19cde895bf65..f30d6ece49fb 100644 --- a/arch/arm/boot/dts/rda8810pl.dtsi +++ b/arch/arm/boot/dts/rda8810pl.dtsi @@ -33,6 +33,21 @@ ranges; }; + modem@10000000 { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x10000000 0xfffffff>; + + gpioc@1a08000 { + compatible = "rda,8810pl-gpio"; + reg = <0x1a08000 0x1000>; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + }; + }; + apb@20800000 { compatible = "simple-bus"; #address-cells = <1>; @@ -60,6 +75,39 @@ <17 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "hwtimer", "ostimer"; }; + + gpioa@30000 { + compatible = "rda,8810pl-gpio"; + reg = <0x30000 0x1000>; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <12 IRQ_TYPE_LEVEL_HIGH>; + }; + + gpiob@31000 { + compatible = "rda,8810pl-gpio"; + reg = <0x31000 0x1000>; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <13 IRQ_TYPE_LEVEL_HIGH>; + }; + + gpiod@32000 { + compatible = "rda,8810pl-gpio"; + reg = <0x32000 0x1000>; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <14 IRQ_TYPE_LEVEL_HIGH>; + }; }; apb@20a00000 { -- 2.17.1 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH 4/4] MAINTAINERS: Add entry for RDA Micro GPIO driver and binding 2019-10-13 11:40 [PATCH 0/4] Add GPIO support for RDA8810PL SoC Manivannan Sadhasivam ` (2 preceding siblings ...) 2019-10-13 11:40 ` [PATCH 3/4] ARM: dts: Add RDA8810PL GPIO controllers Manivannan Sadhasivam @ 2019-10-13 11:40 ` Manivannan Sadhasivam 3 siblings, 0 replies; 7+ messages in thread From: Manivannan Sadhasivam @ 2019-10-13 11:40 UTC (permalink / raw) To: linus.walleij, bgolaszewski Cc: linux-arm-kernel, linux-unisoc, linux-gpio, linux-kernel, orsonzhai, Manivannan Sadhasivam Add MAINTAINERS entry for RDA Micro GPIO driver and devicetree binding. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> --- MAINTAINERS | 2 ++ 1 file changed, 2 insertions(+) diff --git a/MAINTAINERS b/MAINTAINERS index a69e6db80c79..0303502cd146 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -2150,9 +2150,11 @@ L: linux-unisoc@lists.infradead.org (moderated for non-subscribers) S: Maintained F: arch/arm/boot/dts/rda8810pl-* F: drivers/clocksource/timer-rda.c +F: drivers/gpio/gpio-rda.c F: drivers/irqchip/irq-rda-intc.c F: drivers/tty/serial/rda-uart.c F: Documentation/devicetree/bindings/arm/rda.yaml +F: Documentation/devicetree/bindings/gpio/gpio-rda.yaml F: Documentation/devicetree/bindings/interrupt-controller/rda,8810pl-intc.txt F: Documentation/devicetree/bindings/serial/rda,8810pl-uart.txt F: Documentation/devicetree/bindings/timer/rda,8810pl-timer.txt -- 2.17.1 ^ permalink raw reply related [flat|nested] 7+ messages in thread
end of thread, other threads:[~2019-10-15 16:51 UTC | newest] Thread overview: 7+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2019-10-13 11:40 [PATCH 0/4] Add GPIO support for RDA8810PL SoC Manivannan Sadhasivam 2019-10-13 11:40 ` [PATCH 1/4] dt-bindings: gpio: Add devicetree binding for RDA Micro GPIO controller Manivannan Sadhasivam 2019-10-13 11:40 ` [PATCH 2/4] gpio: Add RDA Micro GPIO controller support Manivannan Sadhasivam 2019-10-14 14:25 ` Bartosz Golaszewski 2019-10-15 16:51 ` Manivannan Sadhasivam 2019-10-13 11:40 ` [PATCH 3/4] ARM: dts: Add RDA8810PL GPIO controllers Manivannan Sadhasivam 2019-10-13 11:40 ` [PATCH 4/4] MAINTAINERS: Add entry for RDA Micro GPIO driver and binding Manivannan Sadhasivam
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).