[PATCH AUTOSEL 4.19 013/252] pinctrl: sh-pfc: sh7264: Fix CAN function GPIOs

[PATCH AUTOSEL 4.19 013/252] pinctrl: sh-pfc: sh7264: Fix CAN function GPIOs

[Sasha Levin]

From: Geert Uytterhoeven <geert+renesas@glider.be>

[ Upstream commit 55b1cb1f03ad5eea39897d0c74035e02deddcff2 ]

pinmux_func_gpios[] contains a hole due to the missing function GPIO
definition for the "CTX0&CTX1" signal, which is the logical "AND" of the
two CAN outputs.

Fix this by:
  - Renaming CRX0_CRX1_MARK to CTX0_CTX1_MARK, as PJ2MD[2:0]=010
    configures the combined "CTX0&CTX1" output signal,
  - Renaming CRX0X1_MARK to CRX0_CRX1_MARK, as PJ3MD[1:0]=10 configures
    the shared "CRX0/CRX1" input signal, which is fed to both CAN
    inputs,
  - Adding the missing function GPIO definition for "CTX0&CTX1" to
    pinmux_func_gpios[],
  - Moving all CAN enums next to each other.

See SH7262 Group, SH7264 Group User's Manual: Hardware, Rev. 4.00:
  [1] Figure 1.2 (3) (Pin Assignment for the SH7264 Group (1-Mbyte
      Version),
  [2] Figure 1.2 (4) Pin Assignment for the SH7264 Group (640-Kbyte
      Version,
  [3] Table 1.4 List of Pins,
  [4] Figure 20.29 Connection Example when Using This Module as 1-Channel
      Module (64 Mailboxes x 1 Channel),
  [5] Table 32.10 Multiplexed Pins (Port J),
  [6] Section 32.2.30 (3) Port J Control Register 0 (PJCR0).

Note that the last 2 disagree about PJ2MD[2:0], which is probably the
root cause of this bug.  But considering [4], "CTx0&CTx1" in [5] must
be correct, and "CRx0&CRx1" in [6] must be wrong.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191218194812.12741-4-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pinctrl/sh-pfc/pfc-sh7264.c | 9 ++++-----
 1 file changed, 4 insertions(+), 5 deletions(-)

diff --git a/drivers/pinctrl/sh-pfc/pfc-sh7264.c b/drivers/pinctrl/sh-pfc/pfc-sh7264.c
index e1c34e19222ee..3ddb9565ed804 100644
--- a/drivers/pinctrl/sh-pfc/pfc-sh7264.c
+++ b/drivers/pinctrl/sh-pfc/pfc-sh7264.c
@@ -500,17 +500,15 @@ enum {
 	SD_WP_MARK, SD_CLK_MARK, SD_CMD_MARK,
 	CRX0_MARK, CRX1_MARK,
 	CTX0_MARK, CTX1_MARK,
+	CRX0_CRX1_MARK, CTX0_CTX1_MARK,
 
 	PWM1A_MARK, PWM1B_MARK, PWM1C_MARK, PWM1D_MARK,
 	PWM1E_MARK, PWM1F_MARK, PWM1G_MARK, PWM1H_MARK,
 	PWM2A_MARK, PWM2B_MARK, PWM2C_MARK, PWM2D_MARK,
 	PWM2E_MARK, PWM2F_MARK, PWM2G_MARK, PWM2H_MARK,
 	IERXD_MARK, IETXD_MARK,
-	CRX0_CRX1_MARK,
 	WDTOVF_MARK,
 
-	CRX0X1_MARK,
-
 	/* DMAC */
 	TEND0_MARK, DACK0_MARK, DREQ0_MARK,
 	TEND1_MARK, DACK1_MARK, DREQ1_MARK,
@@ -998,12 +996,12 @@ static const u16 pinmux_data[] = {
 
 	PINMUX_DATA(PJ3_DATA, PJ3MD_00),
 	PINMUX_DATA(CRX1_MARK, PJ3MD_01),
-	PINMUX_DATA(CRX0X1_MARK, PJ3MD_10),
+	PINMUX_DATA(CRX0_CRX1_MARK, PJ3MD_10),
 	PINMUX_DATA(IRQ1_PJ_MARK, PJ3MD_11),
 
 	PINMUX_DATA(PJ2_DATA, PJ2MD_000),
 	PINMUX_DATA(CTX1_MARK, PJ2MD_001),
-	PINMUX_DATA(CRX0_CRX1_MARK, PJ2MD_010),
+	PINMUX_DATA(CTX0_CTX1_MARK, PJ2MD_010),
 	PINMUX_DATA(CS2_MARK, PJ2MD_011),
 	PINMUX_DATA(SCK0_MARK, PJ2MD_100),
 	PINMUX_DATA(LCD_M_DISP_MARK, PJ2MD_101),
@@ -1248,6 +1246,7 @@ static const struct pinmux_func pinmux_func_gpios[] = {
 	GPIO_FN(CTX1),
 	GPIO_FN(CRX1),
 	GPIO_FN(CTX0),
+	GPIO_FN(CTX0_CTX1),
 	GPIO_FN(CRX0),
 	GPIO_FN(CRX0_CRX1),
 
-- 
2.20.1

[PATCH AUTOSEL 4.19 018/252] gpio: gpio-grgpio: fix possible sleep-in-atomic-context bugs in grgpio_irq_map/unmap()

[Sasha Levin]

From: Jia-Ju Bai <baijiaju1990@gmail.com>

[ Upstream commit e36eaf94be8f7bc4e686246eed3cf92d845e2ef8 ]

The driver may sleep while holding a spinlock.
The function call path (from bottom to top) in Linux 4.19 is:

drivers/gpio/gpio-grgpio.c, 261:
	request_irq in grgpio_irq_map
drivers/gpio/gpio-grgpio.c, 255:
	_raw_spin_lock_irqsave in grgpio_irq_map

drivers/gpio/gpio-grgpio.c, 318:
	free_irq in grgpio_irq_unmap
drivers/gpio/gpio-grgpio.c, 299:
	_raw_spin_lock_irqsave in grgpio_irq_unmap

request_irq() and free_irq() can sleep at runtime.

To fix these bugs, request_irq() and free_irq() are called without
holding the spinlock.

These bugs are found by a static analysis tool STCheck written by myself.

Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Link: https://lore.kernel.org/r/20191218132605.10594-1-baijiaju1990@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/gpio/gpio-grgpio.c | 10 ++++++----
 1 file changed, 6 insertions(+), 4 deletions(-)

diff --git a/drivers/gpio/gpio-grgpio.c b/drivers/gpio/gpio-grgpio.c
index 60a1556c570a4..c1be299e5567b 100644
--- a/drivers/gpio/gpio-grgpio.c
+++ b/drivers/gpio/gpio-grgpio.c
@@ -258,17 +258,16 @@ static int grgpio_irq_map(struct irq_domain *d, unsigned int irq,
 	lirq->irq = irq;
 	uirq = &priv->uirqs[lirq->index];
 	if (uirq->refcnt == 0) {
+		spin_unlock_irqrestore(&priv->gc.bgpio_lock, flags);
 		ret = request_irq(uirq->uirq, grgpio_irq_handler, 0,
 				  dev_name(priv->dev), priv);
 		if (ret) {
 			dev_err(priv->dev,
 				"Could not request underlying irq %d\n",
 				uirq->uirq);
-
-			spin_unlock_irqrestore(&priv->gc.bgpio_lock, flags);
-
 			return ret;
 		}
+		spin_lock_irqsave(&priv->gc.bgpio_lock, flags);
 	}
 	uirq->refcnt++;
 
@@ -314,8 +313,11 @@ static void grgpio_irq_unmap(struct irq_domain *d, unsigned int irq)
 	if (index >= 0) {
 		uirq = &priv->uirqs[lirq->index];
 		uirq->refcnt--;
-		if (uirq->refcnt == 0)
+		if (uirq->refcnt == 0) {
+			spin_unlock_irqrestore(&priv->gc.bgpio_lock, flags);
 			free_irq(uirq->uirq, priv);
+			return;
+		}
 	}
 
 	spin_unlock_irqrestore(&priv->gc.bgpio_lock, flags);
-- 
2.20.1

[PATCH AUTOSEL 4.19 023/252] pinctrl: baytrail: Do not clear IRQ flags on direct-irq enabled pins

[Sasha Levin]

From: Hans de Goede <hdegoede@redhat.com>

[ Upstream commit a23680594da7a9e2696dbcf4f023e9273e2fa40b ]

Suspending Goodix touchscreens requires changing the interrupt pin to
output before sending them a power-down command. Followed by wiggling
the interrupt pin to wake the device up, after which it is put back
in input mode.

On Bay Trail devices with a Goodix touchscreen direct-irq mode is used
in combination with listing the pin as a normal GpioIo resource.

This works fine, until the goodix driver gets rmmod-ed and then insmod-ed
again. In this case byt_gpio_disable_free() calls
byt_gpio_clear_triggering() which clears the IRQ flags and after that the
(direct) IRQ no longer triggers.

This commit fixes this by adding a check for the BYT_DIRECT_IRQ_EN flag
to byt_gpio_clear_triggering().

Note that byt_gpio_clear_triggering() only gets called from
byt_gpio_disable_free() for direct-irq enabled pins, as these are excluded
from the irq_valid mask by byt_init_irq_valid_mask().

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pinctrl/intel/pinctrl-baytrail.c | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)

diff --git a/drivers/pinctrl/intel/pinctrl-baytrail.c b/drivers/pinctrl/intel/pinctrl-baytrail.c
index 021e28ff1194e..a760d8bda0af7 100644
--- a/drivers/pinctrl/intel/pinctrl-baytrail.c
+++ b/drivers/pinctrl/intel/pinctrl-baytrail.c
@@ -950,7 +950,13 @@ static void byt_gpio_clear_triggering(struct byt_gpio *vg, unsigned int offset)
 
 	raw_spin_lock_irqsave(&byt_lock, flags);
 	value = readl(reg);
-	value &= ~(BYT_TRIG_POS | BYT_TRIG_NEG | BYT_TRIG_LVL);
+
+	/* Do not clear direct-irq enabled IRQs (from gpio_disable_free) */
+	if (value & BYT_DIRECT_IRQ_EN)
+		/* nothing to do */ ;
+	else
+		value &= ~(BYT_TRIG_POS | BYT_TRIG_NEG | BYT_TRIG_LVL);
+
 	writel(value, reg);
 	raw_spin_unlock_irqrestore(&byt_lock, flags);
 }
-- 
2.20.1

[PATCH AUTOSEL 4.19 123/252] pinctrl: sh-pfc: r8a7778: Fix duplicate SDSELF_B and SD1_CLK_B

[Sasha Levin]

From: Geert Uytterhoeven <geert+renesas@glider.be>

[ Upstream commit 805f635703b2562b5ddd822c62fc9124087e5dd5 ]

The FN_SDSELF_B and FN_SD1_CLK_B enum IDs are used twice, which means
one set of users must be wrong.  Replace them by the correct enum IDs.

Fixes: 87f8c988636db0d4 ("sh-pfc: Add r8a7778 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191218194812.12741-2-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pinctrl/sh-pfc/pfc-r8a7778.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/pinctrl/sh-pfc/pfc-r8a7778.c b/drivers/pinctrl/sh-pfc/pfc-r8a7778.c
index 00d61d1752496..c60fce1225b02 100644
--- a/drivers/pinctrl/sh-pfc/pfc-r8a7778.c
+++ b/drivers/pinctrl/sh-pfc/pfc-r8a7778.c
@@ -2325,7 +2325,7 @@ static const struct pinmux_cfg_reg pinmux_config_regs[] = {
 		FN_ATAG0_A,	0,		FN_REMOCON_B,	0,
 		/* IP0_11_8 [4] */
 		FN_SD1_DAT2_A,	FN_MMC_D2,	0,		FN_BS,
-		FN_ATADIR0_A,	0,		FN_SDSELF_B,	0,
+		FN_ATADIR0_A,	0,		FN_SDSELF_A,	0,
 		FN_PWM4_B,	0,		0,		0,
 		0,		0,		0,		0,
 		/* IP0_7_5 [3] */
@@ -2367,7 +2367,7 @@ static const struct pinmux_cfg_reg pinmux_config_regs[] = {
 		FN_TS_SDAT0_A,	0,		0,		0,
 		0,		0,		0,		0,
 		/* IP1_10_8 [3] */
-		FN_SD1_CLK_B,	FN_MMC_D6,	0,		FN_A24,
+		FN_SD1_CD_A,	FN_MMC_D6,	0,		FN_A24,
 		FN_DREQ1_A,	0,		FN_HRX0_B,	FN_TS_SPSYNC0_A,
 		/* IP1_7_5 [3] */
 		FN_A23,		FN_HTX0_B,	FN_TX2_B,	FN_DACK2_A,
-- 
2.20.1

[PATCH AUTOSEL 4.19 124/252] pinctrl: sh-pfc: sh7269: Fix CAN function GPIOs

[Sasha Levin]

From: Geert Uytterhoeven <geert+renesas@glider.be>

[ Upstream commit 02aeb2f21530c98fc3ca51028eda742a3fafbd9f ]

pinmux_func_gpios[] contains a hole due to the missing function GPIO
definition for the "CTX0&CTX1" signal, which is the logical "AND" of the
first two CAN outputs.

A closer look reveals other issues:
  - Some functionality is available on alternative pins, but the
    PINMUX_DATA() entries is using the wrong marks,
  - Several configurations are missing.

Fix this by:
  - Renaming CTX0CTX1CTX2_MARK, CRX0CRX1_PJ22_MARK, and
    CRX0CRX1CRX2_PJ20_MARK to CTX0_CTX1_CTX2_MARK, CRX0_CRX1_PJ22_MARK,
    resp. CRX0_CRX1_CRX2_PJ20_MARK for consistency with the
    corresponding enum IDs,
  - Adding all missing enum IDs and marks,
  - Use the right (*_PJ2x) variants for alternative pins,
  - Adding all missing configurations to pinmux_data[],
  - Adding all missing function GPIO definitions to pinmux_func_gpios[].

See SH7268 Group, SH7269 Group User’s Manual: Hardware, Rev. 2.00:
  [1] Table 1.4 List of Pins
  [2] Figure 23.29 Connection Example when Using Channels 0 and 1 as One
      Channel (64 Mailboxes × 1 Channel) and Channel 2 as One Channel
      (32 Mailboxes × 1 Channel),
  [3] Figure 23.30 Connection Example when Using Channels 0, 1, and 2 as
      One Channel (96 Mailboxes × 1 Channel),
  [4] Table 48.3 Multiplexed Pins (Port B),
  [5] Table 48.4 Multiplexed Pins (Port C),
  [6] Table 48.10 Multiplexed Pins (Port J),
  [7] Section 48.2.4 Port B Control Registers 0 to 5 (PBCR0 to PBCR5).

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191218194812.12741-5-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/sh/include/cpu-sh2a/cpu/sh7269.h | 11 ++++++--
 drivers/pinctrl/sh-pfc/pfc-sh7269.c   | 39 ++++++++++++++++++---------
 2 files changed, 36 insertions(+), 14 deletions(-)

diff --git a/arch/sh/include/cpu-sh2a/cpu/sh7269.h b/arch/sh/include/cpu-sh2a/cpu/sh7269.h
index d516e5d488180..b887cc402b712 100644
--- a/arch/sh/include/cpu-sh2a/cpu/sh7269.h
+++ b/arch/sh/include/cpu-sh2a/cpu/sh7269.h
@@ -78,8 +78,15 @@ enum {
 	GPIO_FN_WDTOVF,
 
 	/* CAN */
-	GPIO_FN_CTX1, GPIO_FN_CRX1, GPIO_FN_CTX0, GPIO_FN_CTX0_CTX1,
-	GPIO_FN_CRX0, GPIO_FN_CRX0_CRX1, GPIO_FN_CRX0_CRX1_CRX2,
+	GPIO_FN_CTX2, GPIO_FN_CRX2,
+	GPIO_FN_CTX1, GPIO_FN_CRX1,
+	GPIO_FN_CTX0, GPIO_FN_CRX0,
+	GPIO_FN_CTX0_CTX1, GPIO_FN_CRX0_CRX1,
+	GPIO_FN_CTX0_CTX1_CTX2, GPIO_FN_CRX0_CRX1_CRX2,
+	GPIO_FN_CTX2_PJ21, GPIO_FN_CRX2_PJ20,
+	GPIO_FN_CTX1_PJ23, GPIO_FN_CRX1_PJ22,
+	GPIO_FN_CTX0_CTX1_PJ23, GPIO_FN_CRX0_CRX1_PJ22,
+	GPIO_FN_CTX0_CTX1_CTX2_PJ21, GPIO_FN_CRX0_CRX1_CRX2_PJ20,
 
 	/* DMAC */
 	GPIO_FN_TEND0, GPIO_FN_DACK0, GPIO_FN_DREQ0,
diff --git a/drivers/pinctrl/sh-pfc/pfc-sh7269.c b/drivers/pinctrl/sh-pfc/pfc-sh7269.c
index cfdb4fc177c3e..3df0c0d139d08 100644
--- a/drivers/pinctrl/sh-pfc/pfc-sh7269.c
+++ b/drivers/pinctrl/sh-pfc/pfc-sh7269.c
@@ -740,13 +740,12 @@ enum {
 	CRX0_MARK, CTX0_MARK,
 	CRX1_MARK, CTX1_MARK,
 	CRX2_MARK, CTX2_MARK,
-	CRX0_CRX1_MARK,
-	CRX0_CRX1_CRX2_MARK,
-	CTX0CTX1CTX2_MARK,
+	CRX0_CRX1_MARK, CTX0_CTX1_MARK,
+	CRX0_CRX1_CRX2_MARK, CTX0_CTX1_CTX2_MARK,
 	CRX1_PJ22_MARK, CTX1_PJ23_MARK,
 	CRX2_PJ20_MARK, CTX2_PJ21_MARK,
-	CRX0CRX1_PJ22_MARK,
-	CRX0CRX1CRX2_PJ20_MARK,
+	CRX0_CRX1_PJ22_MARK, CTX0_CTX1_PJ23_MARK,
+	CRX0_CRX1_CRX2_PJ20_MARK, CTX0_CTX1_CTX2_PJ21_MARK,
 
 	/* VDC */
 	DV_CLK_MARK,
@@ -824,6 +823,7 @@ static const u16 pinmux_data[] = {
 	PINMUX_DATA(CS3_MARK, PC8MD_001),
 	PINMUX_DATA(TXD7_MARK, PC8MD_010),
 	PINMUX_DATA(CTX1_MARK, PC8MD_011),
+	PINMUX_DATA(CTX0_CTX1_MARK, PC8MD_100),
 
 	PINMUX_DATA(PC7_DATA, PC7MD_000),
 	PINMUX_DATA(CKE_MARK, PC7MD_001),
@@ -836,11 +836,12 @@ static const u16 pinmux_data[] = {
 	PINMUX_DATA(CAS_MARK, PC6MD_001),
 	PINMUX_DATA(SCK7_MARK, PC6MD_010),
 	PINMUX_DATA(CTX0_MARK, PC6MD_011),
+	PINMUX_DATA(CTX0_CTX1_CTX2_MARK, PC6MD_100),
 
 	PINMUX_DATA(PC5_DATA, PC5MD_000),
 	PINMUX_DATA(RAS_MARK, PC5MD_001),
 	PINMUX_DATA(CRX0_MARK, PC5MD_011),
-	PINMUX_DATA(CTX0CTX1CTX2_MARK, PC5MD_100),
+	PINMUX_DATA(CTX0_CTX1_CTX2_MARK, PC5MD_100),
 	PINMUX_DATA(IRQ0_PC_MARK, PC5MD_101),
 
 	PINMUX_DATA(PC4_DATA, PC4MD_00),
@@ -1292,30 +1293,32 @@ static const u16 pinmux_data[] = {
 	PINMUX_DATA(LCD_DATA23_PJ23_MARK, PJ23MD_010),
 	PINMUX_DATA(LCD_TCON6_MARK, PJ23MD_011),
 	PINMUX_DATA(IRQ3_PJ_MARK, PJ23MD_100),
-	PINMUX_DATA(CTX1_MARK, PJ23MD_101),
+	PINMUX_DATA(CTX1_PJ23_MARK, PJ23MD_101),
+	PINMUX_DATA(CTX0_CTX1_PJ23_MARK, PJ23MD_110),
 
 	PINMUX_DATA(PJ22_DATA, PJ22MD_000),
 	PINMUX_DATA(DV_DATA22_MARK, PJ22MD_001),
 	PINMUX_DATA(LCD_DATA22_PJ22_MARK, PJ22MD_010),
 	PINMUX_DATA(LCD_TCON5_MARK, PJ22MD_011),
 	PINMUX_DATA(IRQ2_PJ_MARK, PJ22MD_100),
-	PINMUX_DATA(CRX1_MARK, PJ22MD_101),
-	PINMUX_DATA(CRX0_CRX1_MARK, PJ22MD_110),
+	PINMUX_DATA(CRX1_PJ22_MARK, PJ22MD_101),
+	PINMUX_DATA(CRX0_CRX1_PJ22_MARK, PJ22MD_110),
 
 	PINMUX_DATA(PJ21_DATA, PJ21MD_000),
 	PINMUX_DATA(DV_DATA21_MARK, PJ21MD_001),
 	PINMUX_DATA(LCD_DATA21_PJ21_MARK, PJ21MD_010),
 	PINMUX_DATA(LCD_TCON4_MARK, PJ21MD_011),
 	PINMUX_DATA(IRQ1_PJ_MARK, PJ21MD_100),
-	PINMUX_DATA(CTX2_MARK, PJ21MD_101),
+	PINMUX_DATA(CTX2_PJ21_MARK, PJ21MD_101),
+	PINMUX_DATA(CTX0_CTX1_CTX2_PJ21_MARK, PJ21MD_110),
 
 	PINMUX_DATA(PJ20_DATA, PJ20MD_000),
 	PINMUX_DATA(DV_DATA20_MARK, PJ20MD_001),
 	PINMUX_DATA(LCD_DATA20_PJ20_MARK, PJ20MD_010),
 	PINMUX_DATA(LCD_TCON3_MARK, PJ20MD_011),
 	PINMUX_DATA(IRQ0_PJ_MARK, PJ20MD_100),
-	PINMUX_DATA(CRX2_MARK, PJ20MD_101),
-	PINMUX_DATA(CRX0CRX1CRX2_PJ20_MARK, PJ20MD_110),
+	PINMUX_DATA(CRX2_PJ20_MARK, PJ20MD_101),
+	PINMUX_DATA(CRX0_CRX1_CRX2_PJ20_MARK, PJ20MD_110),
 
 	PINMUX_DATA(PJ19_DATA, PJ19MD_000),
 	PINMUX_DATA(DV_DATA19_MARK, PJ19MD_001),
@@ -1666,12 +1669,24 @@ static const struct pinmux_func pinmux_func_gpios[] = {
 	GPIO_FN(WDTOVF),
 
 	/* CAN */
+	GPIO_FN(CTX2),
+	GPIO_FN(CRX2),
 	GPIO_FN(CTX1),
 	GPIO_FN(CRX1),
 	GPIO_FN(CTX0),
 	GPIO_FN(CRX0),
+	GPIO_FN(CTX0_CTX1),
 	GPIO_FN(CRX0_CRX1),
+	GPIO_FN(CTX0_CTX1_CTX2),
 	GPIO_FN(CRX0_CRX1_CRX2),
+	GPIO_FN(CTX2_PJ21),
+	GPIO_FN(CRX2_PJ20),
+	GPIO_FN(CTX1_PJ23),
+	GPIO_FN(CRX1_PJ22),
+	GPIO_FN(CTX0_CTX1_PJ23),
+	GPIO_FN(CRX0_CRX1_PJ22),
+	GPIO_FN(CTX0_CTX1_CTX2_PJ21),
+	GPIO_FN(CRX0_CRX1_CRX2_PJ20),
 
 	/* DMAC */
 	GPIO_FN(TEND0),
-- 
2.20.1