Re: [PATCH v7 2/7] dt-bindings: pinctrl: add bindings for MediaTek MT6779 SoC

[Rob Herring <robh@kernel.org>]

On Thu, Jul 02, 2020 at 08:57:05PM +0800, Hanks Chen wrote:
> From: Andy Teng <andy.teng@mediatek.com>
> 
> Add devicetree bindings for MediaTek MT6779 pinctrl driver.
> 
> Signed-off-by: Andy Teng <andy.teng@mediatek.com>
> ---
>  .../bindings/pinctrl/mediatek,mt6779-pinctrl.yaml  |  210 ++++++++++++++++++++
>  1 file changed, 210 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/pinctrl/mediatek,mt6779-pinctrl.yaml
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt6779-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt6779-pinctrl.yaml
> new file mode 100644
> index 0000000..3a9fc4d
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt6779-pinctrl.yaml
> @@ -0,0 +1,210 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pinctrl/mediatek,mt6779-pinctrl.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Mediatek MT6779 Pin Controller Device Tree Bindings
> +
> +maintainers:
> +  - Andy Teng <andy.teng@mediatek.com>
> +
> +description: |+
> +  The pin controller node should be the child of a syscon node with the
> +  required property:
> +  - compatible: "syscon"
> +
> +properties:
> +  compatible:
> +    const: mediatek,mt6779-pinctrl
> +
> +  reg:
> +    minItems: 9
> +    maxItems: 9
> +    description: |
> +      physical address base for gpio-related control registers.

Need to describe what each entry is.

items:
  - description: ...
  - description: ...
  - description: ...

> +
> +  reg-names:
> +    description: |
> +      GPIO base register names. The names are "gpio", "iocfg_rm",
> +      "iocfg_br", "iocfg_lm", "iocfg_lb", "iocfg_rt", "iocfg_lt",
> +      "iocfg_tl", "eint";

The names should be a schema.

> +
> +  gpio-controller: true
> +
> +  "#gpio-cells":
> +    const: 2
> +    description: |
> +      Number of cells in GPIO specifier. Since the generic GPIO
> +      binding is used, the amount of cells must be specified as 2. See the below
> +      mentioned gpio binding representation for description of particular cells.
> +
> +  gpio-ranges:
> +    minItems: 1
> +    maxItems: 5
> +    description: |
> +      GPIO valid number range.
> +
> +  interrupt-controller: true
> +
> +  interrupts:
> +    maxItems: 1
> +    description: |
> +      Specifies the summary IRQ.
> +
> +  "#interrupt-cells":
> +    const: 2
> +
> +required:
> +  - compatible
> +  - reg
> +  - reg-names
> +  - gpio-controller
> +  - "#gpio-cells"
> +  - gpio-ranges
> +  - interrupt-controller
> +  - interrupts
> +  - "#interrupt-cells"
> +
> +patternProperties:
> +  '-[0-9]*$':
> +    type: object
> +    patternProperties:
> +      '-pins*$':
> +        type: object
> +        description: |
> +          A pinctrl node should contain at least one subnodes representing the
> +          pinctrl groups available on the machine. Each subnode will list the
> +          pins it needs, and how they should be configured, with regard to muxer
> +          configuration, pullups, drive strength, input enable/disable and input schmitt.

Need to include the pinconf schema here.

> +
> +        properties:
> +          pinmux:
> +            description:
> +              integer array, represents gpio pin number and mux setting.
> +              Supported pin number and mux varies for different SoCs, and are defined
> +              as macros in boot/dts/<soc>-pinfunc.h directly.
> +
> +          bias-disable:
> +            type: boolean

Don't redefine the type. Just indicate what common properties are used:

bias-disable: true

> +
> +          bias-pull-up:
> +            type: boolean
> +
> +          bias-pull-down:
> +            type: boolean
> +
> +          input-enable:
> +            type: boolean
> +
> +          input-disable:
> +            type: boolean
> +
> +          output-low:
> +            type: boolean
> +
> +          output-high:
> +            type: boolean
> +
> +          input-schmitt-enable:
> +            type: boolean
> +
> +          input-schmitt-disable:
> +            type: boolean
> +
> +          mediatek,pull-up-adv:
> +            description: |
> +              Pull up setings for 2 pull resistors, R0 and R1. User can
> +              configure those special pins. Valid arguments are described as below:
> +              0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
> +              1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
> +              2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
> +              3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
> +            allOf:

You can drop the allOf now.

> +              - $ref: /schemas/types.yaml#/definitions/uint32
> +              - enum: [0, 1, 2, 3]
> +
> +          mediatek,pull-down-adv:
> +            description: |
> +              Pull down settings for 2 pull resistors, R0 and R1. User can
> +              configure those special pins. Valid arguments are described as below:
> +              0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
> +              1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
> +              2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
> +              3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
> +            allOf:
> +              - $ref: /schemas/types.yaml#/definitions/uint32
> +              - enum: [0, 1, 2, 3]
> +
> +          drive-strength:
> +            description: |
> +              Selects the drive strength for the specified pins in mA.
> +            allOf:
> +              - $ref: /schemas/types.yaml#/definitions/uint32
> +              - enum: [2, 4, 6, 8, 10, 12, 14, 16]
> +
> +        required:
> +          - pinmux
> +
> +        additionalProperties: false
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +    #include <dt-bindings/pinctrl/mt6779-pinfunc.h>
> +
> +    pio: pinctrl@10005000 {
> +        compatible = "mediatek,mt6779-pinctrl";
> +        reg = <0 0x10005000 0 0x1000>,
> +            <0 0x11c20000 0 0x1000>,
> +            <0 0x11d10000 0 0x1000>,
> +            <0 0x11e20000 0 0x1000>,
> +            <0 0x11e70000 0 0x1000>,
> +            <0 0x11ea0000 0 0x1000>,
> +            <0 0x11f20000 0 0x1000>,
> +            <0 0x11f30000 0 0x1000>,
> +            <0 0x1000b000 0 0x1000>;
> +        reg-names = "gpio", "iocfg_rm",
> +          "iocfg_br", "iocfg_lm",
> +          "iocfg_lb", "iocfg_rt",
> +          "iocfg_lt", "iocfg_tl",
> +          "eint";
> +        gpio-controller;
> +        #gpio-cells = <2>;
> +        gpio-ranges = <&pio 0 0 210>;
> +        interrupt-controller;
> +        #interrupt-cells = <2>;
> +        interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>;
> +
> +        mmc0_pins_default: mmc0-0 {
> +            cmd-dat-pins {
> +                pinmux = <PINMUX_GPIO168__FUNC_MSDC0_DAT0>,
> +                    <PINMUX_GPIO172__FUNC_MSDC0_DAT1>,
> +                    <PINMUX_GPIO169__FUNC_MSDC0_DAT2>,
> +                    <PINMUX_GPIO177__FUNC_MSDC0_DAT3>,
> +                    <PINMUX_GPIO170__FUNC_MSDC0_DAT4>,
> +                    <PINMUX_GPIO173__FUNC_MSDC0_DAT5>,
> +                    <PINMUX_GPIO171__FUNC_MSDC0_DAT6>,
> +                    <PINMUX_GPIO174__FUNC_MSDC0_DAT7>,
> +                    <PINMUX_GPIO167__FUNC_MSDC0_CMD>;
> +                input-enable;
> +                mediatek,pull-up-adv = <1>;
> +            };
> +            clk-pins {
> +                pinmux = <PINMUX_GPIO176__FUNC_MSDC0_CLK>;
> +                mediatek,pull-down-adv = <2>;
> +            };
> +            rst-pins {
> +                pinmux = <PINMUX_GPIO178__FUNC_MSDC0_RSTB>;
> +                mediatek,pull-up-adv = <0>;
> +            };
> +        };
> +    };
> +
> +    mmc0 {
> +       pinctrl-0 = <&mmc0_pins_default>;
> +       pinctrl-names = "default";
> +    };
> -- 
> 1.7.9.5